PSFS at Bilaspur District Bilaspur HP SH Construction of 12 Nos Cat III flats with parking floor including internal external WS and SI Co 10000 liters capacity rain water harvesting tank and development of site i e Co boundary wall interlocking pave

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth any lead and lift as directed by Engineer-in-charge.All kinds of soil.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil all lead and lifts as directed by the Engineer-in- charge. All kinds of soil

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge. All kinds of soil.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete including carriage of material in all leads and lifts.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand) : 8 graded stone aggregate 40 mm nominal size) including carriage of material in all leads and lifts.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:5:10 (1 Cement : 5 coarse sand) : 10 graded stone aggregate 40 mm nominal size) including carriage of material in all leads and lifts.

Providing and laying cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 40 mm nominal size) excluding the cost of centering and shuttering in : Foundatin and plinth including carriage of material in all leads and lifts.

Providing and laying in position cement concrete of specified grade 1:2:4 (1 Cement : 2 coarse sand) : 4 graded stone aggregate 20 mm nominal size) excluding the cost of centering and shuttering - All work up to plinth leve including carriage of material in all leads and lifts.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing 1:5:10 (1 cement : 5coarse sand : 10 graded stone aggregate 40 mm nominal size) including carriage of material in all leads and lifts.

Providing weepholes in brick masonry / stone masonry /plain reinforced concrete abutment, wing wall, return wall with 100 mm dia PVC pipe extending through the full with of the structures with slop of 1(v):20(H) towards drawing face complete as per drawing and technical specification including carriage of material in all leads and lifts.

Stone filling behind retaining walls including carriage of material in all leads and lifts.

Centering and shuttering including strutting, propping etc. and removal of form for : including carriage of material in all leads and lifts.

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick

Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral staircases

Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards.

Edges of slabs and breaks in floors and walls Under 20 cm wide

Cornices and mouldings.

Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. Add for using extra cement in the items of design mix over and above the specified cement content therein. Note:- Excess/less cement over the specified cement content used is payable /recoverable separately. Extra for providing richer mixes at all floor levels. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately) including carriage of material in all leads and lifts.

All works upto plinth level

All works above plinth level upto floor V level

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more including carriage of material in all leads and lifts.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more including carriage of material in all leads and lifts.

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections including carriage of material in all leds and lifts.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:4(1 cement : 4 coarse sand) including carriage of material in all leads and lifts.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in cement mortar 1:6 (1 cement : 6 coarse sand) including carriage of material in all leads and lifts.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) including carriage of material in all leads and lifts.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in cement mortar 1:4 (1 cement: 4 sand) including carriage of material in all leads and lifts.

Half brick masonry with comman burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in cement mortar 1:4 (1 cement: 4 sand) including carriage of material in all leads and lifts

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with Cement mortar 1:6 (1 cement : 6 coarse sand) including carriage of material in all leads and lifts.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.including carriage of material in all leads and lifts

Granite of any colour and shade (i) Area of slab over 0.50 sqm.

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.including carriage of material in all leads and lifts. (a) Granite work.

Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete including carriage of material in all leads and lifts. (a) Fastener with threaded dia 12 mm.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position Sal wood with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). including carriage of material within all leads & lifts.

Providing and fixing flush door shutters decorative type core of block board construction with frames of first class hard wood and well matched first class indian teak plyveneering with vertical grains or cross bends and face vencering on both faces of shutter including carriage of material in all leads and lifts. (a) 40mm thick including black enamelled M.S. butt hinges.

Providing and fixing 40mm thick single/double leaf glazed window shutter made of Ivory coast teak wood having style and top rail and bottom rail 75mm width and chamferred edged moulding 20X12mm for glass panes complete including bright finished balck enamelled iron hinges with necessary screws including carriage of material in all leads and lifts.

Providing and fixing Ivory coast teak wood 40 mm thick wire gauge shutters using galvanised MS wire gauge of IS gauge designation 85G. with wire of dia 0.56 mm for doors windows and providing and fixing Ivory coast teak wood chamfered edged beading of 20 x 12 mm including bright finished black enemelled iron hinges with necessary screws complete as per drawing and specification & as per instruction of Engineer-in-Charge. including carriage of material in all leads and lifts.

Providing & fixing glass panes with putty and nails in doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes including carriage of material in all leads and lifts.

Providing and fixing 1st class indian teak wood plain square edged cover fillets(beading) 40mmx12mm section with wood screws in ceiling and lining including mitring at junctions. including carriage of material in all leads and lifts.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete fixed to steel /wood windows by welding including carriage of material in all leads and lifts.

Fixing stainless steel power coated sliding door bolts of required color and shade with bolts and nuts, screws etc complete (Labour Rate)

Fixing stainless steel power coated tower bolts (barrel type) of required shade and colour with screws, etc. complete (Labour Rate)

Fixing stainless steel power coated handles to required colour and shade with necessary screws, etc. complete (Labour Rate)

Fixing bright finished brass 100mm. Mortice latch and lock and a pair of levers, handles with necessary screws etc. complete (indian make of approved quality) (Labour Rate)

Providing and fixing stainless steel powder coated hooks and eyes:- 150mm including carriage of material in all leads and lifts

Providing and fixing hydraulic door closer of Everest make and manufacture complete including carriage of material in all leads and lifts.

Providing and fixng 100mm bright finished stainless steel power coated floor door stopper with rubber cushion screws etc. to suit shutter thickness complete including carriage of material in all leads and lifts.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) including carriage of material in all leads & lifts.

Providing and laying Vitrified tiles in floor with 600x600 mm size (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately) including carriage of material in all leads and lifts.

Providing and laying Vitrified tiles in 600x600 mm sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately) including carriage of material in all leads and lifts.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge including carriage of material in all leads & lifts. (a) Size of Tile 600x600 mm.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles any size/colour manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of material in all leads & lifts.

Digital tiles in skirting risers of steps and dado in any size/colour 12 mm thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry including carriage of material in all leads and lifts

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete including carriage of material in all leads and lifts.(a) 40 mm thick with 20 mm nominal size stone aggregate.

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete including carriage of material in all leads and lifts.

50 mm thick cement concrete flooring 1:2:4(1 cement:2sand:4gradedstone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement,including carriage of material in all leads and lifts.

Cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing completeincluding carriage of material in all leads and lifts.

Extra for making chequers of approved pattern on cement concrete floors, steps, landing, pavements etc. including carriage of material in all leads and lifts.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in- Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. including carriage of material in all leads and lifts.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required including carriage of material in all leads & lifts.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 1518 microns using self drilling/ self tapping screws complete including carriage of material in all leads & lifts.

Ridges plain (500 - 600mm)

Flashings/ Aprons.( Upto 600 mm)

Gutter (600 mm over all girth)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including carriage of material in all leads and lifts.

Steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of red lead paint including carriage of material in all leads and lifts.a) In beams joists channels, angles, tees, flats with connection plates or angle cleats as in main and cross beams ,hip and jack rafters, purlins connected to common rafters and the like.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required including carriage of material in all leads and lifts.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves board / facia / soffits / ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in charge, (Base members of steel work shall be measured and paid separately) including carriage of material in all leads and lifts.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes including carriage of material in all leads and lifts 110 mm diameter

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.including carriage of material in all leads and lifts:-110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion including carriage of material in all leads and lifts

Coupler 110 mm

Bend 87.5° 110 mm bend

Shoe (Plain) 110 mm Shoe

Applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works including carriage of material in all leads and lifts

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications (a) Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture including carriage of material in all leads and lifts.

Applying priming coat with ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) including carriage of material in all leads and lifts

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications (a) Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture including carriage of material in all leads and lifts.

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) including carriage of material in all leads and lifts

CEMENT PLASTER (IN FINE SAND) 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand) including carriage of material in all leads and lifts

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix 1:3 (1 cement: 3 fine sand) including carriage of material in all leads and lifts.

CEMENT PLASTER (IN FINE SAND) 20 mm cement plaster of mix including carriage of material in all leads and lifts

Cement mortar 1 : 4 (1 cement : 4 fine sand)

Cement mortar 1 : 6 (1 cement : 6 fine sand)

20 mm Cement plaster 1:4 (1 cement: 4 coarse sand) finished with a floating coat of neat cement including carriage of material in all leads and lifts

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade new work (two or more coats) over and including water thinnable priming coat with cement primer including carriage of material in all leads and lifts.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of material in all leads and lifts.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen including carriage of material in all leads and lifts (i) first coat of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including ounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including carriage of material in all leads and lifts.

Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand) including carriage of material in all leads and lifts.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall.15x22 cm in cement mortar 1:6 (1 Cement : 6 Sand) and inside plastring with cement plaster 1:3 (1 Cement:3 Sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1 Cement : 5 Sand : 10 graded stone aggregate) of 40 mm nominal size) and 7.5 cm cement concrete 1:2:4 (1 Cement : 2 Sand : 4 Graded stone aggregate of 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design.) including carriage of material in all leads and lifts.

Providing and fixing 40 mm nominal bore garvanised M.S. tube (light grade) cut let in cement mortar 1:3 (1 Cement : 3 Sand)including carriage of material in all leads and lifts.

Polishing two coats with french polish on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt,dust,and sand papered smooth and including a coat of wood filler including carriage of material in all leads and lifts.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm including carriage of material in all leads and lifts

Making chases up to 7.5x7.5 cm in walls for G.I. pipe and filling the same with cement concrete 1:3:6 ( 1 cement: 3 Sand: 6 graded stone aggregate 20 mm down gauge )and finishing with matching surface after housing G.I. pipe etc. including carriage of material in all leads and lifts.

Extra for addition of synthetic Polyester triangular fibre of length 12mm, effective diameter 10-40 microns and specific gravity of 1.34 to 1.40 in cement concrete / RCC / Flooring / water retaining structures by using 125gms of synthetic Polyester triangular fibre for 50 Kg cement used as per directions of Engineer-in-Charge. including carriage of material in all leads and lifts.

Supplying and fixing expended metal to wood or steel members in partitions etc. including carriage of material in all leads and lifts. (a) Weight exceeding 3kg and not exceeding 5kg per Sqm.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work Exposed on wall including carriage of material in all leads and lifts.

15mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work including carriage of material in all leads and lifts.

20mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete including carriage of material in all leads and lifts:-25 to 40 mm nominal bore

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge. INTERNAL WORK - EXPOSED ON WALL including carriage of material in all leads and lifts.

1216 (16mm O.D.) pipe.

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level including carriage of material in all leads and lifts:-1000 litres net capacity tank.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

75 mm dia.

110 mm dia.

Providing and fixing PVC single equal branch with ovel access door, ISI marked insertion rubber washer 3mm thick bolts and nutscomplete including fixing with approved adhsive etc. complete including carriage of material in all leads and lifts.

110 mm dia

75 mm dia

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

110 mm dia.

75 mm dia.

Providing and fixing PVC single equal branch plain including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

110 mm dia.

Providing and fixing PVC collers ISI marked of approved design fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

110 mm dia

75 mm dia

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

110 mm dia

75 mm dia

Providing and fixing PVC Cowl ISI marked of approved design fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

110 mm dia

75 mm dia

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of material in all leads and lifts.

110 mm dia

75 mm dia

Fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting.(i) 610mmx510mm with bowl depth 200 mm (confirming to BIS Specifications) including carriage of material in all leads and lifts. (Labour Rate)

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including carriage of material in all leads and lifts:-110 mm X 75 mm.

Providing and fixing 100 mm dia cromium plated stainless steel grating confirming to BIS specifcation including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

Fixing vitreous china wash down water closet (European type WC pan) with intergal "P" or "S" trap including jointing the trap with soil pipe in cement mortar 1:1 ( 1 cement :1 sand)Plastic seat and cover to be measured and paid for seperately including carriage of material in all leads and lifts confirming to BIS specification. (Labour Rate)

Ordinary closet

Anglo Indian (Universal closet)

Providing and fixing plastic seat (solid / Holow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers. (i) Solid type: (a) White plastic seat and cover (confirming to BIS Specifications). including carriage of material in all leads and lifts.

Fixing vitreous china wash basin with single/double hole for pillar tap with C.I. Or M.S brackets painted white including cutting holes and making good the same including white cement whereever required.(ESS-ESS/CZAR/NOVA) (Labour Rate)

Flat back (ii) 550mmx400mm

560mm X 400 mm (Oval type under counter)

Fixing C.P. brass waste for wash basin or sink (ESS-ESS/CZAR/NOVA) (a) 32mm dia. (Labour Rate)

Providing and fixing of G.I. Union for wash basin or sink 32 mm dia. confirming to BIS specifcation including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P brass screws and washers complete. confirming to BIS specifcation including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA).

Fixing 600mmx20mm size C.P Brass towel rail complete with C.P Brass brackets fixed to wooden plugs with C.P brass screws confirming to BIS specifcation(ESS-ESS/CZAR/NOVA). (Labour Rate)

Fixing 600mmx120mm glass shelf with C.P brass brackets and guard rail complet fixed to wooden plugs with C.P Brass screws confirming to BIS specifcation (ESS-ESS/CZAR/NOVA).(Labour Rate)

Providing and fixing toilet paper holder confirming to BIS specifcation including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

Fixing C.P. brass soap dish with C.P.brass brackets fixed to wooden plugs with C.P. brass screws, and confirming to BIS specifications,. (Labour Rate)

Fixing 15mm dia C.P. brass bib tap with capstan head including carriage of material in all leads & lifts. (Confirming to BIS Specifications) (Labour Rate)

Fixing one hole basin maxing faucet including carriage of material in all leads & lifts. (Confirming to BIS Specifications) (Labour Rate)

Fixing C.P. bottle trap for wash basin and sink (Confirming to BIS Specifications) (a) 32mm dia (Labour Rate)

Fixing vitreous china padestal for wash basin complete recessed at the back for the reception of pipes and fittings .(ESS-ESS/CZAR/NOVA) (Labour Rate)

Fixing brass angle valve 15mm without nuts and pipe (ESS-ESS/CZAR/NOVA) (Labour Rate)

Fixing Mixer for kitchen sink with casted swinging spout at top confirming to BIS specifications, (ESS-ESS/CZAR/NOVA) (Labour Rate)

Fixing wall mixing faucet for shower and bath with ovrhead pipe (1210cm) and bath shower confirming to BIS specifications.(ESS-ESS/CZAR/NOVA) (Labour Rate)

Fixing C.P. Brass shower rose with 15mm or 20mm inlet 150 mm dia .(ESS-ESS/ CZAR/NOV (Labour Rate)

Providing and fixing P.V.C connection pipe with bras unions. (a) 30cm length / 45 cm length (I) 15mm Nominal size bore (confirming to BIS Specifications) including carriage of material in all leads & lifts. (ESS-ESS/CZAR/NOVA)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete including carriage of material in all leads and lifts:-. 32mm dia

Fixing brass full way value with wheel (confirming to BIS Specifications) including carriage of material in all leads & lifts. (ESS-ESS/CZAR/NOVA) (Labour Rate)

15mm nominal bore.

20 mm nominal bore.

Providing and fixing G.I./M.I. Union of following sizes (where not included in the item) (confirming to BIS Specifications) including carriage of material in all leads & lifts. (ESS-ESS/CZAR/NOVA)

Providing and fixing PTMT Coloured / white high density polythelene / poly propylene 10 litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float,with push button,couplings for connections with inlet, outlet and ovrflow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow) pipe to be measured and paid for separately including carriage of material in all leads and lifts.

Providing and fixing stone ware gully trap grade 'A' complete with C.I. Grating, brick masonary chamber in cement mortar 1:5 and water tight C.I. Cover with frame of 300mmx300mm size (inside)the weight of cover to be not less than 4.53 kg and frame tobe not less than 2.72 kg. including carriage of material in all lead and lifts. (I) 1 square mouth traps (i) 100mmx100mm (P-Type).

Cutting holes through existing brick/stone work including making good the same in cement mortar 1:6( 1cement:6 sand) per cms. Depth of cutting including carriage of material in all leads and lifts(i) Holes up to and including 400 sqcm in area.

Fixing 15mm dia C.P. brass concealed stop cock .(confirming to BIS Specifications) i (ESS-ESS/CZAR/NOVA). (Labour Rate)

Providing and fixing PVC 'P' or 'S' trap for water closet (squatting pan) including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete. including carriage of material in all leads and lifts confirming to BIS specification Ist quality:-(a) 110 mm dia.

Providing chases 75mm wide 50mm deep (average size) in walls for conduit pipes and filling the same with cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregate 20 mm and down gauge after the conduit pipe is laid (excluding the cost of conduit pipe). including carriage of material in all leads and lifts.

Providing and fixing PTMT jet spray of approved quality with 1.5 mtr. tube. (confirming to BIS Specifications). including carriage of material in all leads and lifts.

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete, including carriage of material in all leads and lifts. (a) 1200 dia R.C.C. pipe.

Providing 200 mm wide cast iron Rungs with chequered or ribbed non slip surface including fixing in manholes with 200 mm x 200 mm x 100 mm cement concrete 1:3:6 (1Cement:3Sand:6graded stone aggregate 20 mm nominal size) including carriage of material in all leads and lifts.

Supplying and fixing cast iron cover with frame for manhole of 500mm internal diameter C.I. cover (medium duty) the weight of cover to be not less than 58 kg including carriage of material in all leads and lifts.

Constructing manhole with RCC top slab in 1:2:4 mixure (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 ( 1 cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1 cement : 3 sand finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete including curing and testing. including carriage of material in all leads and lifts.

Inside size 800x800mm and 500mm deep including SFRC Cover with frame (medium duty) total weight of cover and frame to be not less than 173 kg (weight of cover 103kg on and weight of frame 70 kg With 230 mm walls of brick masonary using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3 sand)

Inside size 800x800 mm and 1000 mm deep deep including SFRC Cover with frame (medium duty) total weight of cover and frame to be not less than 173 kg (weight of cover 103 kg on and weight of frame 70 kg With 230 mm walls of brick masonary using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3 sand).

Inside size 1200x900 mm and 1000 mm deep deep including SFRC Cover with frame (medium duty) total weight of cover and frame to be not less than 173 kg (weight of cover 103 kg on and weight of frame 70 kg With 230 mm walls of brick masonary using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3 sand).

Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 :150 mm dia Ductile Iron Class K-7 pipes including carriage of material in all leads and lifts.

Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and the cost of rubber gasket including carriage of material in all leads and lifts.

Constructing soak pit 2.5 metre diametre 3.00 metre deep with45x45cm dry brick honey comb shaft with bricks of class designation 75 and soil waste drain pipe 100mm diameter 1.80 metre long as per standard design with F.P.S. including carriage of material in all leads and lifts.

RAKESH GOEL

Suket Construction Co. Pvt. Ltd.

SHIV RAM