SPECIAL REPAIRS FOR REPLACEMENT OF WINTER APPLIANCES GEYSER AGAINST BER AND OTHER SANCTIONED WORKS IN ARMY AREA UNDER GE ARMY NO 1 JODHPUR

Amount

Surface excavation not exceeding 30cm and averaging 15 cm deep and getting out in any type of soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in any type of soil complete all as specified and as directed .

Returning filling in excavated soil, including spreading, leveling, watering and well ramming in layer n. exc 25 cm complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50 mtr and depositing where directed at a level not exc.1.50 mtr above the starting point, complete all as specified and directed.

M&L for sand filling under floor or in foundations including watering and consolidation complete all as specified and as directed.

M&L for hard core broken stone of gauge n. exc. 63mm, deposited, spread and levelled in layers n. exc. 15cm thick, water and rammed to a true surface, complete all as specified and as directed.

M&L for cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in foundations filling, sub base and mass concrete filling, etc, complete all as specified and as directed.

M&L for plain cement concrete 1:2:4, type B1 (using 20mm graded crushed stone aggregate), as in floor finish topping layer, complete all as specified & directed.

M&L for squared rubble walling, Jodhpur type, regular coursed, well bonded ,bedded and solidly hearted built in cement mortar 1:6, complete all as specified and directed.

Extra over stone walling for hammer dressing to face stone & dressing of face beds & joints as specified of squared rubble walling Jodhpur type brought upto courses with maximum depression of face from straight edge held against the dressed surface n exc 20mm and dressing face beds and joints, complete all as specified and directed.

M&L for keyed pointing in cement mortar (1:3) to squared rubble masonry regular coursed or un coursed complete all as specified & directed.

M&L for 15 mm thick Rendering in CM 1:4 on stone masonry or other than fair faces of brick work & finishing the surfaces even & fair w/o using extra cement, including mixing with water proofing compound ( WPC) as per manufacturer instructions complete all as specified and directed. Note :- WPC will be measured and paid separately as supply only.

M&L for 15 mm thick rendering in CM 1:6 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing finished fair and even without using extra cement, complete all as specified and as directed.

M&L for 5 mm thick Rendering in CM 1:3 on fair faces of brick work or conc surfaces as in ceilings & finished even & smooth w/o using extra cement, complete all as specified and as directed.

M&L 40mm thick, PCC (1:2:4) type B-0 using 12.5 mm graded crushed stone aggregate as in damp proof course to horizontal or vertical surfaces including mixing with WPC and necessary form work complete all as specified and as directed. NOTE :- WPC shall be measured and paid separately under respective item.

M&L for Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash on ceiling surfaces complete all as specified and as directed.

M&L for preparation of new plastered or un-plastered surfaces of walls and applying two coats of cement base paint over & including M&L a coat of white wash to match with the existing surface complete all as specified and as directed.

M&L for preparing new plastered or unplastered surfaces and applying 2 mm thick wall care putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper on walls, complete all as specified and directed. Note -i)- Rate are deemed to be included for scaffolding, trestles, ladders, cradles, etc. necessary for execution of work and protective measures. ii)- OBD shall be in one or more colours/ shades all as approved by GE.

M&L precast cement concrete block masonry using PCC 1:2:4, type B-1 solid blocks, 10 cm thick and setting in cement mortar 1:4, straight or curved on plan exceeding 6 m mean radius complete all as specified and directed.

M&L 50 mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate laid in alternative bays as in plinth protection including finishing the surface even & fair & filling the joints with mastic filling i.e one part of bitumen 85/25 and 3 parts of sand by weight in 2 mtr interval, complete all as specified and directed.

M&L Machine cut kota stone slab 20-25 mm thick as in floor laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including M&L 20mm thick screed bed in CM 1:6, complete all as specified and as directed.

M&L Machine cut kota stone slab 20-25 mm thick as in riser of steps, skirting, dado & pillar laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including M&L 10mm thick screed bed in CM 1:4, complete all as specified and as directed.

M&L of 20-25 mm thick machine cut KOTA stone slab as in shelves (Single piece) fixed in walls machine cut, laid over cement and jointed with grey cement slurry with pigment to match the shade of the slab, including rubbing and Mirror polishing, complete all as specified and as directed.

S&F factory made box type windows (steel) (BWM) with side hung shutter including cooler opening as shown in Drg No CEJZ/TD/20 sheet1/3 to 3/3 complete with glazing bars, dovetailed or welded, complete all as specified and as directed by Engr-in-Charge. Note : Both shutter (wherever applicable) will be jointed internally with flat iron of size 40 x 4mm and quoted rate deemed to include the cost component of the same.

All as per item No. 24.00 here-in-above, but without glazing bars, complete all as specified and directed.

S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and directed.

M&L for rolled mild steel sections like angle, channel, flat, square etc as in framed work such as grills, gratings, etc, with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars ,barred iron doors; ladders ;framed balusters walk ways railings framed work of water tanks and similar work confirming to Fe-290Gde E-165 complete all as specified and as directed.

S&F glavanised steel wire cloth, 0.56mm nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tack or galvanised wire stapples complete all as specified and as directed.

M&L for framed brackets for cooler stand as shown in Drg No CEJZ/TD/72/2015 sheet1/1 of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel') complete all as specified and as directed.

M&L factory Made flush shutters, 40 mm thick solid core with particle board core construction both face is covered with decorative face veneer with lipping/frame to match as per IS 2202(part-I, 1999) . The stiles & rails shall be with out any joint and made with non- coniferous timber hard wood (Hillock/ Mirantee/ Bosum/ Benteak) with moisture content not less than 12% as per IS. The face panel comprising of ply wood or cross band and face veneers shall be glued by hot pressed process. The over all finished thickness of face panel shall not be less than 40mm while the thickness face veneer shall not be less than 0.6 mm complete all as specified and directed.

M&L for 35mm thick factory made 2nd class hard wood glazed and skelton shutter and open rebated and prepared to receive glass, gauge etc (without sash bars), edges or framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part-I Section 8 Clause 8.24 (a) complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-1 by using 20 mm graded stone aggregate as in bed block for fixing of hold fast complete all as specified and as directed.

M&L for mild steel work as in hold fasts, clamps, bands, straps or stays, wall ties, hooks etc confirming to Fe - 290, Grade E-165 including prepartion of surfaces and treated with coal tar and sanded with clean sharp sand complete all as specified and directed.

S&F 150mm long aluminium anodised handle extruded section, complete all as specified and as directed by Engr-in-Charge.

S&F of stainless steel butt hinges 100mm size, include screws or bolts, nuts and washers to match the butt hinge, complete all as specified and as directed.

S&F of aluminium alloy anodised sliding door bolt with hasp and staple bolt type and fixings clips of sheet cast or extruded sections and fixings bolts and sliding bolts of extruded sections and fixed 16mm dia and 200mm long, complete all as specified and directed.

S & F floor door stopper of size 140 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed.

S&F 200mm size aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

Preparation of new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over & including M&L a coat of pink primer complete all as specified and as directed .

Preparation of new or previously untreated steel surface of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over & including M&L a coat of red- oxide, zinc chrome primer complete all as specified and directed.

S&F decorative type curtain rod stainless steel finish of pipe 22 to 25 mm dia with best quality knob metal with double fitting type including stainless steel brackets fixed to walls complete with two nos decorative stainless steel knobs at each end (as approved by GE).

S&F stainless steel plate rack of size 750mm X 1200mm X 200mm of approved pattern made out of stainless steel sheet 0.50 mm thick suitable for stacking more than 15 Nos Plates with round 8mm dia rods complete all as sample kept on GE office.

S&F of water GI tubing medium grade, galvanized, with all fittings fixed to wall, ceilings or laid n floors, complete all as specified and directed. (a) 25 mm bore,

All as per item No. 43.00 here-in-above, but size 20 mm bore

All as per item No. 43.00 here-in-above but 15 mm bore including cutting chases, pinning in & making good to disturbed portion to match the existing surface etc., complete all as specified and directed.

S&F rotational moulded polythene water storage tanks of 1000 ltrs capacity, white three layered (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I with PTMT ball valve heigh pressure with epoxy coated aluminium rod and high density plastic ball suitable for 20mm bore pipe weight not less than 210gms, complete all as specified and directed.

Supply and fixing gun metal globe or gate valve with iron wheel head, screwed both ends for jointing 20 mm bore iron pipe, non rising forged brass spindle class I complete all as specified and directed by Engineer -in-Charge.

All as per item No. 47.00 here-in-above, but suitable for 25 mm bore pipe

S&F stainless steel sink with drainage board, for kitchen or laboratory, made of stainless steel 1 mm thick, with plugs, washers and waste pipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to waste pipe, over all size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm, including brass waste coupling,complete all as specified and as directed.

S&F bib cock with flange 15mm dia, chromium plated, long body, cast copper alloy, fancy type, screwed for iron pipe or for brass ferrule, complete all as specified and directed.

S & F vitreous china ware wash hand basin, white, flat back of size 550 mm X 400 mm including 32 mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe, PVC connection15mm size with PTMT nuts of length 450mm long including pillar tap, cast copper alloy, chromium plated, 15 mm dia, with capstan head, screwed down high pressure with or with out lettered "Hot" or "Cold" with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and as directed.

S&F Angular stop cock with wall flange, choromium plated long thread, screwed both ends for 15 mm bore iron pipe or for unions complete all as specified and as directed

S & F sand cast, cast iron, soil / waste / vent pipes, 75mm bore, in any length with or without ears, jointed with cement sand mortar, laid in trenches or in floors complete all as specified and as directed.

M & L for PCC 1:2:4, type B-1 [using 20 mm graded granite stone aggregate] in surface channels or benching and drains including forming fair finished drain or channel using extra cement including forms, moulds, mitred / stooped ends complete all as specified and as directed.

Supply, laying, testing & commissioning of 150 mm bore reinforced cement concrete pipes, one end socketed, class NP2, laid in trenches and jointed complete all as specified and as directed .

Supply, laying, testing & commissioning of 200 mm bore reinforced cement concrete pipes, one end socketed, class NP2, laid in trenches and jointed complete all as specified and as directed .

M&L for cement concrete 1:3:6 type C2 by using 40mm graded crushed stone aggregates for foundation of poles / struts / stays etc complete all as specified and as directed .

M & L for PCC 1:2:4, type B-1, using 20 mm graded stone aggregate as in roof kerb, coping to parapet wall, manhole & other similar work and the like including weathering, slightly rounded or chamfered angles and throating and necessary form work, complete all as specified and as directed.

Removing excavated soil to a distance exceeding 250 mtr & not exceeding 500 mtr and depositing where directed at a level not exc.1.50 mtr above the starting point, complete all as specified and directed.

S&F cast iron foot steps not exceeding 5 KG each in manholes, complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel [½ round or ¾ section] in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required for 150 mm bore of pipe complete all as specified and as directed.

All as per item No. 62.00 here-in-above, but suitable for 200 mm bore pipe

Supply and laying machine pressed / factory made chamfered edge cement concrete rubberised interlocking paver block, 60mm thick with 6 mm thick top layers of anti abrasive material of M-35 grade with any colour, design & pattern, & size/ shape, as approved by GE as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness made by table vibratory method using PU mould, laid in required colour & pattern over and including M&L 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

Supply and laying machine / factory made kerb stone of M-25 grade,at or near ground level, cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required, complete all as specified and directed.

S&F mild steel TMT bar 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam, slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clip, complete all as specified and as directed.

S&F mild steel TMT bar 5 mm dia and over upto and including 10mm dia as in stirrups cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam etc., hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clip, complete all as specified and as directed.

M&L for reinforced cement concrete (design mix) M-25 as in as in beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and as directed.

M&L for reinforced cement concrete (design mix) M-25 as in slabs supproted on walls,beams and column in floors, roofs, landings etc., complete all as specified and as directed.

M&L for use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits [if any] of foundation and plinth beams and similar work, vertical or to batter for rough finished surfaces complete all as specified and as directed.

M&L for use and waste form work to sides and soffits of floor or roof beams, lintel, cantilevers, shelves etc. including support of fair finished surfaces, complete all as specified and as directed.

M&L for use and waste of formwork to soffits of slabs not exc. 200mm thick and similar works fair finished surfaces of concrete, complete all as specified and as directed.

M&L for use and waste of form work to edge of concrete flats, treads, breaks in floors, window cills, concrete railing, opening in concrete walls, floor and roofs not exc 20cm wide and side of RCC/PCC bands in walls horizontal or sloping and similar work exc 10cm but not exc 20cm wide with fair finished surfaces, complete all as specified and as directed.

M&L for neat cement slurry @ 3.00 kg/Sqm and screeding / bedding layer of 10 mm thick in CM 1:3 mixed with water proofing compound as per manufacturer instructions over the RCC roof slab for laying of water proofing treatment including providing the following as roof treatment complete all as specified and as directed : - (a) FIRST COURSE: Applying a coat of bituminous primer @ 0.4 litre / Sqm manufactured by the same agency that of APP with a density 0.87 to 0.89 Kg/litre at 25 degree celsius on prepared plastered surfaces. (b) SECOND COURSE: Applying one coat of bonding material using blown type bitumen conforming to IS-702 grade 85/25 @ 1.20 Kg/Sqm (c) THIRD COURSE : Provide a layer of APP modified polymeric membrane centre core of 100mm micron HMHDPE, outer film 20 micron each, thickness 3.00mm having weight not less than 3.00 Kg/Sqm using torch application method with minimum 10cm side lap and 15cm end lap complete . (d) FOURTH COURSE : Applying one coat of bonding material using blown type bitumen conforming to IS- 702 grade 85/25 @ 1.20 Kg/Sqm. (e) FIFTH COURSE : 40 mm thick plain cement concrete 1:2:4 (using 20 mm stone crushed aggregate) as in roof padding, including WPC as per manufacturer instruction.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance out side MD land complete all as specified and as directed.

M&L for Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash on ceiling surfaces complete all as specified and as directed.

M&L for preparation of newly plastered surface of walls and applying two or more coats of 100% premium acrylic emulsion weather proof paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and directed. Note -i)- Rate are deemed to be included for scaffolding, trestles, ladders, cradles, etc. necessary for execution of work and protective measures. ii)- Paint shall be in one or more colours/ shades all as approved by GE.

M&L for 25 mm thick plain cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in sub base of flooring, including finishing the surface even & rough to receive tiling etc., complete all as specified and directed.

M&L for glazed colour ceramic tiles (premium quality) of size 300X450X6-7 mm, as in vertical surface such as i.e. dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over & including M&L 10mm thick backing coat in CM (1:4) complete all as specified and directed.

M&L for non skid ceramic coloured tiles (premium quality) of size 7 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including M&L 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

S& F PVC connections 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

S&F brass chrome plated soap dish holder fancy type complete all as specified & directed by Engineer in charge.

S & F over head shower rose 150X150mm square shape single flow, ABS body and face plate brass with CP, arm 300mm long joiting to 15 mm bore pipe complete all as specified and as directed.

S&F health faucet 80 mm dia and 1.2mtr long with wall hook and flexible tube, complete all as specified and as directed. Make : Jaquar Cat No. ALD-573 or equivalent in Kohler/ Cera as approved by GE.

S & F CP two way angle bib cock with wall flange, screwed down high pressure,screwed both ends for 15 mm bore iron pipe or for unions complete all as specified and as directed. Make: Model No.KUP-35041PM of JAQUAR make or equivalent model in Kohler/ Cera as approved by GE

S&F 10 ltrs capacity PVC valve less, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of 32 mm dia and PVC connection 15mm size, 450 mm long with PTMT nuts complete all as specified and as directed.

S&F toilet paper holder viterous china toilet paper holder, complete all as specified and as directed.

S&F MS chromium plated peg set of five fixing with wall, complete all as specified and as directed.

S&F swivel shower of PTMT any colour with shower rose of 100 mm dia suitable for 15 mm bore pipe, shower arm 195mm long with bend of 45 degree with flange of PTMT any colour (minimum weight 40 gms) all as specified & directed.

M&L for writing letters or figures with (Block roman italic or Indian) exc 30cm high of suitable width as required at site with two coats of flourescent paint, complete all as specified and directed.

S & F in replacement white vitreous china squatting pan "Orissa pattern" of size 580 mm X 440 mm with integral foot rests and PVC 'P' or 'S' trap including provision of cement concrete bedding 1:5:10 type E2 complete all as specified and as directed.

S&F tubular towel rail 20 mm dia chormium plated brass 'D' type 600mm long with bracket fixed with chormium plated brass screws, complete all as specified and as directed.

S & F sand cast, cast iron, soil / waste / vent pipes, 100mm bore, in any length with or without ears, jointed with cement sand mortar, laid in trenches or in floors complete all as specified and as directed.

S & F sand cast, cast iron, soil / waste / vent pipes, 100mm bore, in any length with or without ears, jointed with cement sand mortar, fixed to wall, complete all as specified and as directed.

S&F CI bends any radius suitable for 100mm bore pipe with oval acess door, complete all as specified and as directed.

S&F CI connector of length 30 cm suitable for 100mm bore pipe with oval acess door, complete all as specified and as directed.

S& F 100 mm bore CI branch piece, single (single Y) equal or unequal complete all as specified and directed.

S& F 100 mm bore CI branch piece, double (double Y) equal or unequal complete all as specified and directed.

S&F CI bends any radius suitable for 75mm bore pipe with oval acess door, complete all as specified and as directed.

S& F 75 mm bore CI branch piece, single (single Y) equal or unequal complete all as specified and directed.

S& F 75 mm bore CI branch piece, double (double Y) equal or unequal complete all as specified and directed.

S&F 100mm dia CI floor trap plain grating including jointing with solvent cement, complete all as specified and as directed.

S&F Cast iron nahani trap with CP grating out let diameter 75mm including jointing to waste pipe fixed in cement mortar 1:1, complete all as specified and as directed.

S&F of box type steel ventilator with top hung shutter including shop coat zinc chromate & hinges with steel handle, and steel peg stay, complete without glazing bars, complete all as specified and directed.

S&F of box type steel ventilator with top hung shutter including shop coat zinc chromate & hinges with steel handle, and steel peg stay, complete with glazing bars, complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm wood grain printed PVC Sheet on back face, Panelling of wood grain printed PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.complete all as specified and directed.

S&F 150mm size aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

M&L PCC 1:3:6 type C-2 (using 40 mm graded crused stone aggregate) as in bed to150 mm bore NP-2 drain pipe including packing under and haunching against the side of pipe after they are laid and tested complete all as specified and directed by Engineer in charge.

Supply only integral water proofing compound ISI Marked all as specified.

S&F rolled mild steel framed work as in chowkats of doors or gates of angle or other section confirming to Fe 410-W (Gde E-250 quality-A) with gusset plates, rails braces, etc., complete, drilled for fixing of steel sheeting or other covering door etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door, fittings and hanging, also fastering and fixing complete all as specified and as directed.

M&L precast cement concrete (1:3:6) type C-1by using 20mm graded stone aggregate as in solid block masonry exceeding 10cm width and setting in cement mortar 1:6 complete all as specified and as directed.

Rendering 10mm thick on PCC block / concrete surface of walls in CM 1:4, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for Preparation of new plastered or unplastered surfaces of wall and applying three coats of white wash on wall surfaces complete all as specified and as directed.

Demolition of stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as directed.

All as per item No. 9.00 here-in-before, but except stone complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and removing rubbish to out side MD land complete all as specified and directed.

M&L for GI frame work for seamless ceiling comprising of GI perimeter chanel 0.55mm thick with two unequal flanges of 20 & 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm c/c intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm c/c with GI cleat and steel expansion fasteners with and including ceiling section (not exceeding 1.2M length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to intermediate channel at 457mm c/c and hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and including M&L for applying 02 mm thick plaster of paris over and including S&F Perforated particle board/ tiles for insula-tion and accoustic purposes, 60x60 cm in size, fixed with nails to timber frameworkorwith staples on snap grid including ismantling of existing false ceiling of any thickness with cover fillets complete all as specified and as directed.

M&L in replacement of prepainted galvalume aluminium zinc coating GI based corrugated steel sheeting 0.50 mm thick any colour having tensile strenght 550Mpa in roof coverings fixed with self tapping screws, including dismantling old u/s plain or corrugated steel sheeting, any gauge, any thickness complete all as specified and directed.

S&F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc., complete all as specified and directed.

S&F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. including M&L for anodised aluminium hard ware as indicated, glazing clips, rubber packing, anodised aluminium snap on beading for fixing glass panes in frames, fixing of shutters with fittings shall be as per manufacturers instructions complete all as specified and directed. Note:- Glass and other filling material in panels shall be measured and paid for separately.

S&F Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws including M&L for anodised aluminium hard ware as indicated, glazing clips, rubber packing, anodised aluminium snap on beading for fixing glass panes in frames, fixing of shutters with fittings shall be as per manufacturers instructions complete all as specified and directed. Note:- Glass and other filling material in panels shall be measured and paid for separately.

S&F of 5 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane, complete all as specified and directed.

S&F Aluminium grill medium grade size 50x50 mm, fixed at outer edge of door/window, complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in surface channel or benching and drains including finishing the top of benching even and smooth using extra cement (Forming fair finished channel shall be measured separately), complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms , moulds , mitred/stopped ends etc., complete all as specified and as directed.

S&F stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aparture 1.00mm and fixed with tinned tack or galvanised wire stapples complete all as specified and as directed.

E/M items Supply, laying, jointing, testing and commissioning 1100 volt grade heavy duty XLPE insulated LT under ground cable, sheathed, as per IS- 7098 (Part I) 1988, galvanized steel strip armoured heavy duty multi stranded aluminum conductor laid in trenches / passed through pipe/duct road crossing, fixed on poles/ wall with clamps made out of mild steel flat iron including fixing accessories like brass cable glands double compression type, lugs, nuts, bolts, washers etc of size 2 core 10 sqmm, complete all as specified and directed Note: - (i) Excavation and earthwork, sand cushioning, PCC cable cover, shall be measured and paid separately in relevant item here in after .

M&L for dry clean fine river sand as in sand cushioning to underground cable including punning down of sand layer, complete all as specified and as directed. Note :- Punned thickness shall only be measured and paid.

Supplying and laying un-reinforced precast concrete cable cover, class HVP, type 2, flat, size 300mm x 180mm x 40mm, complete all as specified and directed.

M&L for galvanised steel tubing, medium grade, for protection of cable, laid in trenches/road crossing/floor or fixed to pole/wall with all fittings, of size 40 mm bore, complete all as specified and directed.

M&L for road cutting (width not exceeding 3.50 mtr)and excvation upto 60 cm below ground level and laying 40 mm bore protection pipe size of 5 RM length and make good disturbed surface as per existing, complete all as specified and directed.

M&L point wiring using approved colour coding (Red , Black and Green for single phase circuits) as per IS code -694 with valid CML No., with multi stranded copper conductor 1.5 sq mm nominal cross-sectional area, single core, PVC insulated and sheathed FRLSH cable 1100 Volts grade, ISI marked, in and including heavy duty PVC casing N capping of 25/32mm size with accessories surface mounted in wall/roof/floor etc, ISI marked with PVC surface mounted gang box(with earth dolly), with cover plate(ISI Marked) cover for fixing of switches, sockets and fan regulators etc, inciuding PVC insulated & sheathed multistranded copper conductor 1.5 sq mm nominal cross sectional area single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly for One light/fan/bell point controlled by one, one way switch, complete all as specified and directed.

All as per serial Item No. 133.00 above but for one 3 pin socket outlet 5/6 Amps on the same board with other switches complete all as specified and directed.

All as per serial Item No. 133.00 above but for one 3 pin socket outlet 5/6 Amps on the independent board, complete all as specified and directed.

All as per serial Item No.133.00 above but for 16 Amps 3 pin socket point on independent board with 4.00 Sqmm PVC insulated FRLSH multi-stranded copper conductor with 4.00 Sqmm PVC insulated & FRLSH multi-stranded copper conductor as earth wire complete all as specified and directed .

S&F piano type switch, one way, 6 Amps, 1 module, complete all as specified and directed.

S&F piano type switch, one way, 16 Amps, 1 module, complete all as specified and directed.

S&F socket outlet, 2/3 Pin, combined 2 module, 6 Amps, complete all as specified and directed.

S&F socket outlet, 6 Pin, combined 2 module, 6/16 Amps, complete all as specified and directed.

M&L ceiling rose, 3 phase / PVC / Polycarbonate, isolated body, ISI Marked, complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 20/22W, 4 feet, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed.

S&F bldg security LED Light Luminaire of 35 Watts having IP 65/66 protection fiting made out of pressure die cast Aluminium housing, operating Voltage 140-270 Volts with in built surge protectore, toughened glass with and including GI pipe 32mm dia bracket of 1.5 m in length including drilling holes, nuts & bolts 2 coats of red oxide primer on GI pipe and fixing with wall security light on building wall connecting cable, complete all as specified and directed.

S&F and testing factory made sheet metal enclosure for MCB DB SPN 8 way 240 volt with double door, IP - 43 protection duly fixed/concealed in wall complete and making good disturbed surfaces of wall, floor etc including necessary connection lugging with copper lugs pin/ring type, complete all as specified and as directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

Supply, fixing, testing and commissioning SP 6 to 32 Amps 240V 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection, complete all as specified and as directed.

S&F ceiling fans with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep, min air delivery 210 CFM with service value 6.00 BEE, 5 star rated with brushless direct current motor (BLDC) connecting up with and including three core flexible PVC insulated multi stranded copper condutor of size 1.0 sqmm from ceiling rose/ conector to fan (earth wire to connected to fan hook), ISI marked, complete all as per directed and specifed

Earthing complete with galvanised steel earth plate electrode 60 x60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in elevtrical plate no. 3 connected to Earthing test point all as specified or indicated including testing on completion Note : (i) Rates are deemed to be included for necessry earth work ,PCC pit , RCC cover etc complete. (ii) Earth lead shall be up to 7.5 Mtr and rates are deemed to be included for GI pipe 15mm Light grade upto 7.5 mtrs for protection of earth wire 4.0 mm dia, complete all as specified and as directed.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.complete all as specified and as directed

S&F exhaust fan, heavy duty steel body, AC single phase 300 mm sweep complete with louvers including cutting / making holes in wall fixing/grouting of frame & connecting with & including 3 core PVC insulated copper conductor flexible cable of size 23/0.0076 (or eq. Size in mm) from ceiling rose to fan, complete all as specified and as directed.

S&F sub main wiring with two runs of PVC insulated but unsheathed multi stranded copper conductor FRLSH cable 1100 volt grade of size 2.50 Sqmm and one run of 2.50 Sqmm single core PVC insulated but unsheathed multi stranded copper conductor FRLSH cable (Phase-Red, Neutral-Black, Earth-Green) 1100 volt grade as earth lead drawn through in and including non metallic PVC conduit of size 25 mm dia (external) with wall thickness not less than 1.8 mm, (ISI marked) concealed in wall including accessories like bends, tees junction boxes, etc fixed in wall or ceiling etc., complete all as specified and as directed. NOTE: Two runs of 2.50 Sqmm cable with one run of 2.50 Sqmm earth wire and PVC conduit shall be measured & paid for as one length.

All as per item No. 151.00 here-in-above, but cable size 4.00 Sqmm

Supply, fixing, testing & commissioning of advanced ESE lightening protection system including OPR lightning conductor, lightning stroke counter, surge protective device, protecting flat, test point, stainless steel clips, coupling accessories, hooks, duck foot connector, equipotential box, protecting flat, extension mast, conductor supporting stud etc for building, as per site requirement and directed by Engr In Charge

S&F copper strip 25mm x 3.15 mm with saddles and fixing screws etc on roof and down conductor above ground level complete all as specified and as directed.

S&F copper strip 32x6 mm buried in ground 150 mm below ground including all necessary excavation and earth work, connecting at ends, jointing etc complete all as specified and as directed.

S&F single pointed copper rod 12 mm dia and 300 mm long fixed with the roof in and including all fittings, fixtures and PCC 1:2:4 type B-1 block of size 100mmx100mm x100mm complete all as specified and as directed.

M&L test point terminal block made of gun metal or phosphorous bronze 75x75x25 mm of 6mm thickness or copper strip of 32 X6 mm 100 mm long drilled and screwed including 4 Nos 8mm dia 25mm long hexagonal head brass screws including box of size 90x90x90mm made of 1.6mm plain sheet painted with two coats of synthetic enamel paint over a coat of red oxide primer , and screwed to wall for protection of test point, complete all as specified and as directed.

M&L for chemical earthing complete with copper plate electrode of size 90cm x 60cm x 5 mm thick burried directly in ground vertically at a depth not less than 2.25 metre deep below normal ground level with top edge of the plate not less than 1.5 metre below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal dust d filling the environment friendly earth enhancing BACKFILL compound (conductolite) 25 kg bag and common salt, filling in alternate layer and electrode connections by using 32 X 6 MM size of copper strip by means of bolts, nuts, check nuts and washers made of copper and protected by light grade 40 mm dia GI pipe connected to main switch board or main control board, and GI pipe light grade 20 mm bore for watering and including funnel, wire mesh, RCC pit cover with handle and PCC chamber pit with PCC 1: 3:6 type C1 and earth pit angle iron 25x25x3mm including excavation and earth work, disposal of surplus soil to a distance not exc. 50 mtr all as specified and as shown on Plate No 3 of SSR Part I (2009)and Part II (2020) complete all as specified and directed by Engr-in-Charge.

Taking down carefully aluminium/copper point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendent, regulators, sockets, bell push, bell, light fittings etc. removing serviceable materials to store for keeping in safe custody for reuse at site or for taking credit (Credit shall be made as per Schedule of credit), removing rubbish from the site and making good all disturbed surfaces of walls, floors etc. to match to the existing surfaces, complete all as directed.

M&L point wiring (concealed) using approved colour coding (Red , Black and Green for single phase circuits) as per IS code -694 with valid CML No., with multi stranded copper conductor 1.5 sq mm nominal cross-sectional area, single core, PVC insulated and sheathed FRLSH cable 1100 Volts grade, ISI marked, in and including stove enamelled steel conduit of dia not less than 20 mm, with accessories concealed in wall/roof/floor etc, ISI marked with fire proof prestressed steel sunken / concealed box suitable for flame proof switch rotary type with terminal box in LM6, 16A, single pole 250 V, (with earth dolly) duly painted two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally and two coats of black bituminous paint over a coat of red oxide primer externally, with 1 module cover plate(ISI Marked) cover for fixing of switches, sockets and fan regulators etc, inciuding PVC insulated & sheathed multistranded copper conductor 1.5 sq mm nominal cross sectional area single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly for One flame proof light point controlled by one, one way flame proof switch, complete all as specified and directed.

S&F switch flame proof rotary type with termination box in LM6, 16A, single pole 250V, complete all as specified & directed.

Supply and fixing LED light fitting 1x16 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size, complete all as specified & directed.

S&F and testing factory made sheet metal enclosure for MCB DB SPN 4 way 240 volt with double door, IP - 43 protection duly fixed/concealed in wall complete and making good disturbed surfaces of wall, floor etc including necessary connection lugging with copper lugs pin/ring type, complete all as specified and as directed.

Supply, fixing, testing and commissioning SPN 10 Amps 240V 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection, complete all as specified and as directed.

Supply, fixing, testing and commissioning SPN 40 Amps 240V 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection, complete all as specified and as directed.

Supply,fixing, testing and commissioning of addressable smoke (white colour) detector with mounting base, with inbuilt test button and with power operated / ultra alkaline battery, wireless signal output, max area coverage 49 Sqm with 13 f eet height, including wireless optical smoke sensor, analogue system through radio waves compatibility, plugs into surface base mounting, red LED indication, photo electric light scatter detection principle, 12 V power connection / 9 volts DC battery operating voltage, unique address embedded in detector addressing method, indoor type, moulded ABS, Dimensions: 106mm (Dia) x 36mm (H), complete all as specifeied and directed by Engr - in - Charge. Make GE/Honeywell/Bluestar as approved by GE

Supply, install and testing Intelligent hooter (Red color) with flasher light wireless type in heavy abc engineering plastic box all mounting accessories, complete as required. Inclding transmitter to transmit signal of manual call point / smoke detector, wireless hooter cum flasher with module, analogue smoke sensors through radio waves compatibility, plug into surface base mounting, hooter cum flash light indication, 105 db sound, reads different zones of smoke sensors principle function and push the signals so as to collect and read by wireless panel, 12 volts DC operating voltage, 2 pin 5 Amp socket is required to be connected and charging, 10 Nos 1.2 V (AAA size) battery, 6 Hours power backup, unique address embedded in detector, indoor type, made out ABS Plastic body, complete all as specifeied and directed by Engr - in - Charge. Make GE/Honeywell/Bluestar as approved by GE

Supply,fixing, testing and commissioning of intelligent wireless manual call station (red colour), modern push type emergency button with set & reset button with safety cover, with Lock / un-lock facility optional, radio transmitter through radio waves, fix into moulded box, unique address embedded, indoor type, moulded ABS, complete all as specifeied and directed by Engr - in - Charge. Make GE/Honeywell/Bluestar as approved by GE

Supply,fixing, testing and commissioning of microprocessor based Intelligent wireless digital addressable fire alarm centralised panel, digital type alarm control panel with capacity 100 devices, event historical logging, input AC power supply, automatic battery charger, 12 volts sealed maintenance free lead acid batteries complete with Compatibility - radio emitter through radio waves,Indication, Alarm 105 db, displays different zones of smoke sensors transmitted by Hooter cum flasher, 12 volts DC ( Rechargeable batteries) Operating voltage, two pin 5 Amp socket is required to be connected for charging, 7 to 8 Hours Power Backup, digital nos. display on screen with display manual chart,Indoor type, mild steel body, 12V DC, 1.2 AH Battery, complete all as specifeied and directed. Make GE/Honeywell/Bluestar as approved by GE

Supply,testing and installation of electric storage geyser of capacity 25 Ltrs, BEE 5 star rating, 230Volts, AC, 50Hz, comprising of heating element 2000 watt, anitcorrosive inner tank, magnesium anode protection, puff insulation,both power indicating LED lamp and heating indicating LED lamp neccasry suitable 3 core copper cable, complete with all accessories such as safety valve, thermostat, NRV, suitable plug top, inlcluding supply and fixing of inlet and out let connection to geyser with steel grip, chromium plated, hose braided PVC connection of 600mm in length - 02 Nos suitable for GI pipe 15mm dia (out let PVC connection should be capable to withstand the designed temparature of Geyser) and geyser shall be fixed on wall surface with wall mount bracket and 10 cm anchor bolts as required inclduing all necessary plumbling works and civil works complete all as directed and as specified. Note:- Minimum warranty 2 years on product, 3 years on heating element & 7 years on inner tank.

All as per item No. 170.00 here-in-above, but geyser of capacity 50 Ltrs, BEE 4 star rating,

M&L single pole and neutral enclosure with two pin earth industrial plug and socket with one MCB SP 20 Amps complete all as specified and as directed.

S&F stop valves, 15 mm dia, cast copper alloy with capstan head, chromium plated, fancy type, screwed down high pressure with crutch or butterfly handle with long shank and cup [concealed type] for iron pipe etc complete all as specified and as directed.

M&L cutting into existing GI pipeline, inserting Tee of required size suitable for connecting 15 mm bore pipe, complete all as specified and as directed.

Disconnection & taking down carefully geyser any capaity any make, from existing location / position and deposite to AGE E/M-I store yard for safe custody and making good disturbed surface as per existing, complete all as specified and as directed.

Note for item No. 74.00: - (i)- A Information Tablet will be put up in the front side wall of the buildings where this work will be done. All building/structure shall be provided with plaque (tablet) furnishing the information as per PS clause, in plaster engraving in and painted as directed by GE (ii)- WPC shall be measured and paid separately under respective item..

Note for item No. 158.00: - Make: ASHLOK / M/S McML Protection Technologies Pvt Ltd. / M/S JMV Earthing Equipment Pvt Ltd / M/S JEF Techno Solutions (P) Ltd. Note :-(i) The carbon based compound shall have a resistance value of less than 01 ohm. The compound shall be filled up to required level ie (3 .0 mtr ) of earth pit. (ii) The necessary excavation & earth work is required to be included in the rate quoted.

Note for all items:- (i) All items in BOQ are for "Materials and labour / Supply and fix" and to be executed in "Repairs/Replacement unless otherwise specifically mentioned as "Supply only" or Fixing only" in BOQ Bidders are required to quote their rates accordingly. (ii) The contract sum shall be arrived at after duducting amount of schedule of "Credit" from the Total quoted amount (iii) Makes of materials will be approved by GE in writing before commencement of work. (iv)- Quantities are clubbed in BOQ for different Jobs. For which ref. Annexure-I on Sl. page. No. 44 (R) to 47 (R) of tender document.

Nikhat nirman

M/s Bajrang Electricals

LOKESH ELECTRICAL WORKS CONTRACTOR