REPAIRS AND PAINTING TO STEEL FURNITURES OF VARIOUS UNTIS OTM AND MD ACCNS UNDER GE NW KOCHI

Amount

Dismantling/removing the U/S or serviceable ply top from GI pipe charpoy and dismantle the frame completely, replace the broken/unserviceable parts with new ones, reassembling the charpoy frame completely in all respects by inserting/screwing in the existing/replaced long/short rails and legs inside the 3 way elbow 32 mm duly tightened with check nuts and re fixing the serviceable ply wood removed from the existing charoy and keep the frame ready complete all as specified and directed. Notes :- (i) New parts required shall be measured and paid separately as supply only. (ii) Quoted rate is inclusive of labour element for providing new parts.

Supply only new long rail, 1880mm long, 32mm dia, medium grade GI, Class 'B' conforming to IS-1239 (pt1) of 1979 having threaded portions 22mm long, on each end complete all as specified and directed.

Fabrication/making of short rail, 800mm long, threaded 22mm for both ends made out of long rail obtained from item No 2 above complete all as specified and directed.

Fabrication/making of leg, 375mm long, duly threaded on top end up to 22mm made out of short/long rail obtained from item No.3. above including provn of FI clamps for fixing hard wooden block plugs at bottom as required complete all as specified and directed.

Removal of one serviceable leg from GI pipe charpoy with ply top without disturbing the charpoy frame and removing the existing wooden block along with screw levelling/plaining by cutting/scraping the bottom of leg to make charpoy symmetrically horizontal and refix the removed wooden block after providing 34mm dia and 3mm thick mild steel sheet by spot welding at three places to form leg base and refix the leg to charpoy properly complete all as specified and directed.

S&F 32mm dia 3 way elbow class B as per IS 1239 (Pt II) 1982 complete all as specified and directed.

Supply & Re-fix the plywood 12 mm thick commercial as per the size of Charpoy GI/Charpy with ply top as complete all as specified and directed.

S&F in repair check nut 32 mm dia hexagonal shaped class B quality as per IS 1239 (Pt II) 1982 complete all as specified and directed.

S&F CP steel handle 125mm long made to shape and fixing the same to make the 3 way locking system fully operational including removing the unserviceable handle for almirah steel of any size and type complete all as specified and directed..

S&F three way locking device including plane rod MS rod to match with originalto making the system fully operational for Almirah large steel. including removing the unserviceable locking system complete all as specified and directed (Drg No.FD-109/114 (m)/351/67 (m)/1031/1033/TP).

S&F three way locking device including plane rod MS rod to match with original to making the system fully operational for Almirah small/medium steel. including removing the unserviceable locking system complete all as specified and directed. (Drg No.FD-67(m)/114 (m) / 350 / 1032/1034 )

M&L for straightening and denting to shutters/body of almirah steel of different size including replacing worn out/broken hinges with suitable hinges, greasing etc all shown on Drg complete all as specified and directed.{Drg No FD-243,67(m),1031/1032/1033/1034/TP}

S&F new key hole with brass lock of 50mm six lever, duly fixed inside face of front shutter with stainless steel keys in duplicate for almirah steel of any size and type complete all as specified and directed..(Drg No.FD-109/114 (m)/ 115(m) /350/351 /67(m)/1031/ 1032/1033/ 1034/TP)

S&F by welding or jointing to the bottom of steel almirah channel base/leg of length 440mm/484mm as per drg, each consisting of 1mm thick two MS sheet channel base 70mm wide 100mm high with the open end bent out wards up to 15mm, the ends of the channel shall be covered with 70 mm x 100mm MS sheet of 1mm thick incluidng two coats of synthetic enamel paint olive green colour over a coat of zinc chrome primer for Almirah small/medium steel including removing the unserviceable channel base/leg complete all as specified and directed. .(Drg No.FD-67(m)/114 (m)/350/1032 1034 )

S&F by welding or jointing to the bottom of steel almirah channel base/leg of length 440mm/484mm as per drg, each consisting of 1mm thick two MS sheet channel base 70mm wide 100mm high with the open end bent out wards up to 15mm, the ends of the channel shall be covered with 70 mm x 100mm MS sheet of 1mm thick incluidng two coats of synthetic enamel paint olive green colour over a coat of zinc chrome primer for Almirah large steel including removing the unserviceable channel base/leg complete all as specified and directed. (Drg No.FD-109/114 (m)/ 115(m)/351 /67(m)/1031/ /1033/ TP )

S&F by welding or jointing to the bottom of steel almirah channel base/leg of length 440mm/484mm as per drg, each consisting of 1mm thick two MS sheet channel base 70mm wide 100mm high with the open end bent out wards up to 15mm, the ends of the channel shall be covered with 70 mm x 100mm MS sheet of 1mm thick incluidng two coats of synthetic enamel paint olive green colour over a coat of zinc chrome primer for Locker steel including removing the unserviceable channel base/leg all as directed by the Engineer-in-Charge.(Drg No.FD 257 / 1029 )

S&F 1mm thick mild steel single shelf fixed to three sides (inside) the steel almirah as shown in drawing bent to 25mm on sides, back and in front and further bent upwords to 10mm in front and sides of shelves, duly painted with two coat of synthetic enamel paint olive green colour over a coat of zinc chrome primer for Almirah small/medium steel complete all as specified and directed. Drg No.FD-67(m)/114 (m)/350/1032 1034)

S&F 1mm thick mild steel single shelf fixed to three sides (inside) the steel almirah as shown in drawing bent to 25mm on sides, back and in front and further bent upwords to 10mm in front and sides of shelves, duly painted with two coat of synthetic enamel paint olive green colour over a coat of zinc chrome primer for Almirah Large steel complete all as specified and directed. (Drg No.FD-109/114(m)/115(m)/351/67(m)/1031/1033/TP)

S&F 1mm thick mild steel single shelf fixed to three sides (inside) the steel almirah as shown in drawing bent to 25mm on sides, back and in front and further bent upwords to 10mm in front and sides of shelves, duly painted with two coat of synthetic enamel paint olive green colour over a coat of zinc chrome primer for Locker steel complete all as specified and directed. (Drg No.FD-257/1029)

S&F 20mm dia CP steel conduit pipe, with 1.6 mm wall thickness, with sockets at both ends 380mm long for Locker steel fixed in repairs complete all as specified and directed. (Drg No.FD-257/1029/1034)

S&F safty type, CP brass hasp and staple 75mmx40mm x3mm fixed on the shutter of locker steel in repairs complete all as specified and directed. (Drg No.FD-257/1029)

S&F 50mm long tower bolt, chromium plaled steel, single lower or upper, duly welded to the shutter fixed in repairs complete all as specified and directed. (Drg No.FD-257)

S&F single 125mm CP steel bow handle on the left or right shutter fixed in repairs complete all as specified and directed. (Drg No.FD-257/1029)

S&F rear leg for chair CBB steel 19mm dia ERW conduit, 16G , 56 cm long made to shape, top of the leg welded to lower part of the back of the chair including two coats of synthetic enamel paint olive green colour over a coat of zinc chrome primer and provn of PVC shoe at bottom and PVC cap at top fixed in repairs complete all as specified and directed. (Drg No.FD-75(m))

S&F 19/25mm dia ERW conduit 16G 1.29 Mtr long made to shape, side vertical back, front leg portion and horizontal seat portion, duly welded to rear leg of chair CBB steel including 2 coats of synthetic enamel paint olive green over a coat of red oxide primer with provn of PVC cap on top and PVC shoe at bottom fixed in repairs complete all as specified and directed. [Drg No.FD-75(m)]

M&L for one seat or back frame made out of second class hard wood (chir or venteak or thampakam) 40mm wide & 25 mm thick, made to shape, duly given 2 coats of black synthetic enamel paint over a coat of wood primer, duly caned as per Godrej pattern with new white plastic, cane and fixed on the seat/back of chair CBB steel with 65 mm long machine screws with washers, 2 each on each side fixed in repair complete all as specified and directed. (Drg No.FD-75(m))

M&L for new 19/25mm dia, 1.6mm thick MS conduit made to shape for chair CBA steel forming both the handle portions, vertical leg portions and the horizontal base portion complete, with the handle ends duly welded to the middle portions of the back rest and front legs, refixing the existing arm rests to the handles and providing 4 Nos hard rubber toes to the base including 2 coats of synthetic enamel paint olive green over a coat of zinc chrome primer to steel conduit frame fixed in repairs complete all as specified and directed. (Drg No.FD-75(m)

M&L for providing 19/25mm dia, 1.6mm thick MS conduit to the lateral (one side) seat and back portion of chair CBA steel duly welded to the front legs and handle portion and applying 2 coats of synthetic enamel paint olive green over a coat of size chrome primer to the entire steel conduit frame of the chair and fixing the existing seat and back caned frame to the chair complete fixed in repairs complete all as specified and directed. (Drg No.FD-75(m)

M&L for new teak wood handle, made to shape, 400mm long, 50mm wide and 25mm thick, front end duly curved suitable for chair CBA steel duly painted with 2 coats of black synthetic enamel paint over a coat of wood primer and fixing the handles to the arm rest portion of chair with screws from bottom complete fixed in repairs complete all as specified and directed. (Drg No.FD-75(m)

M&L for providing one seat or back frame made out of IInd class hard wood (venteak/ Thampakam/chir), 40mm wide and 25mm thick on all four sides, made to shape and painted with 2 coats of synthetic enamel paint black over a coat of wood primer, duly caned with 2mm wide plastic cane as per Godrej pattern, including fixing the seat/ back frame to the chair CBA steel with 65 mm machine screws with nuts and washers fixed in repairscomplete all as specified and directed. (Drg No.FD-75(m))

S&F 04 Nos MS strip of size 60mmx30mmx4mm thick by welding to the existing frame below the seat of chair with out/with arm including provision one hole for fixing the seat by screwing and two coats of synthetic enamel paint olive green over a coat of red oxide primer as complete all as specified and directed. (Drg No.FD-75(M)

S&F new table top for table office clerk/general/typist steel of 18mm thick pre laminated teak veneered particle board, with 4mm thick teak wood beading all side duly polished, fixing the top to the table top frame with screws from bottom complete fixed in repairs complete all as specified and directed. (Drg No.FD-84(m)/FD-1004)

All as per item No. 33 but for table office officer steel top of size 1370mmx760mm x18mm thick. complete all as specified and directed. .(Drg No.FD-84(m)/FD-1003)

All as per item No 33 above but top of 900x900mm (18mm thick) for table 900x900x760mm steel.complete all as specified and directed. (Drg No.FD-1009)

S&F new lock, 4 lever aluminum body, locking bolt lever of cast brass with stainless steel keys in duplicate, suitable for table office clerk/general/typist fixed to the shutter or top drawer and providing automatic locking system to the other three drawers complete fixed in repairs complete all as specified and directed. (Drg No.FD 84 (m)/1002 /1003/1004/1005/1008)

S&F bucket for receptacle (large) with 1mm thick GI sheet 210mm dia at bottom and 340 mm dia at top and internally 335mm high, bottom of bucket shall have 25mmx3mm flat iron welded to circular sheet of GI bucket, top of bucket shall have 50mm x 65mm and 3mm thick FI MS sheet welded to bucket for holding 10mm dia MS round bar handle of bucket as shown on drg and complete all as specified and directed. (Drg No.FD-43(m)/FD-368/FD-1044)

S&F bin for receptacle small cylindrical, closed at bottom and of 290mm dia and 315mm high made of 1mm thick GI sheet, two brackets of 50mmx65mmx3mm thick FI mild steel sheet welded to bin for holding 10mm dia MS bar handle, 40mmx 3mm MS flat iron ring shall be provided at bottom of the bin,all as shown on drawing and complete all as specified and directed. (Drg No.FD-1045/FD-226(m))

M&L for preparation of old painted surfaces by rubbing down with and paper, without any scratching or damaging the existing coat, clean throughly to remove all dust/oily spot etc and applying one coat of synthetic enamel paint as color approved by GE to all in side and out side surfaces of the item painted complete all as specified and directed. for Shoe rack steel {Drg No FD/E6/MAP/02 (R) }

M&L for preparation of old painted surfaces by rubbing down with and paper, without any scratching or damaging the existing coat, clean throughly to remove all dust/oily spot etc and applying one coat of synthetic enamel paint as color approved by GE to all in side and out side surfaces of the item painted complete all as specified and directed. for Bed Hard MAP {Drg No FD/E6/MAP/08 (R)}

M&L for preparation of old painted surfaces by rubbing down with and paper, without any scratching or damaging the existing coat, clean throughly to remove all dust/oily spot etc and applying one coat of synthetic enamel paint as color approved by GE to all in side and out side surfaces of the item painted complete all as specified and directed. for Charpoy IP Hard Top {Drg No FD/MAP-II/01}

PRIYADARSHINI CONSTRUCTIONS

SHANMUGA TRADERS

M/s T.P SHAJI

Mahesh Traders

Albert Rebello and Company