Provn of drainage in CSD depot, LPG and Oxygen cylinder store room in MH and bath rooms at OTM accn of 2/9 GR under GE Dehradun

Amount

Surface dressing in soft/loose soil n exc 15 cm deep trimming of natural ground (removing vegetation/shurbs/ brushwood. Undergrowth and carring away rubbish to a distance of 50 metre complete all as specified and directed.

Excavation in trenches n exc 1.5 mtr wide and n exc 1.5 mtr in depth for foundation etc, or for shafts, wells, cesspits manholes, pier holes etc. n exc 10 Sqm on plan and n exc. 1.5 mtr in depth and getting out in any type of soil complete all as specified.

M&L for PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation filling / mass concrete complete all as specified and directed by Engr-in-Charge.

M&L for PCC (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) as in coping, bed plates and chamfered angles and throating etc complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for RCC type A-1, 1:1.5:3 (using 20mm graded stone aggregate) as in foundation, including rafts footing, fountdation beams, plinth beams, base for columns etc and mass concrete work complete all as specified and directed.

M&L for RCC(1:1½:3) type A-1 (using 20mm graded crushed stone aggregate) for columns, pillars,piears, posts & struts etc complete all as specified and directed.

M&L for RCC(1:1½:3) type A-1 (using 20mm graded crushed stone aggregate) for Beams, cantilevers, bresummers, lintel over 1.5m span etc complete all as specified and directed.

M&L for RCC (1:1½:3) type A-1 (using 20mm graded crushed stone aggregate) as in chajja etc complete all as specified and directed.

M&L for cement concrete(1:2:4) type D-2 (using 20mm graded crushed stone aggregate) as in surface channels and drains complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) (1:1½:3) type A1 (using 20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. (Note :- Reinforcement & formwork shall be measured and paid for separately)

M & L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for steel formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for fair finished surface complete all as specified

M & L for steel formwork to sides of pillars, posts, struts, piers, columns and stanchions square rectangular or ploygonal for fair finished surface of concrete complete all as specified and directed.

M&L for steel formwork for fair finished surface to sides of concrete walls, retaining walls, abutments, parapets and staircase railling and similar work including attached pillasters, but tresses etc vertical or to batter complete all as specified and directed.

M&L steel form work to sides and soffits of flat floors or roof beams, beam haunchings, girderrs, bressum-mers, lintels cantilevers, shelves including supports, overhangs, etc also splays between floors and beams, etc for fair finished surface, complete all as specified & directed

M&L for steel formwork to chajjas, through and similar items including edges for fair finished surface, complete all as specified and directed.

M&L for steel form work to soffits of suspended slab such as roof slabs, floors slabs, landing & similar work not exceeding 200 mm thick (Horizontal or sloping) etc for fair finished flat surfaces complete all as specified & all as directed

M&L steel form work to edges of concrete flats, treads, breaks in floors, window cills, concrete raillings, opening in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide for finished surface complete all as specified.

Material and labour for TMT bar 8 mm dia and over cut to length bent to shape required including cranking bending for hooping and binding with and including mild steel wire not less than (0.9 mm) dia complete all as specified.

M&L for reinforced cement concrete in Type A-1 (1:1.5:3) (using 20mm graded crushed stone aggregate) for walls retaining walls, basement walls, ballast walls and the line andy thickness above top of footings including attached pilasters and buttresses and complete all as specified and directed.

M&L for brick work with subclass 'B' bricks, , straight or curved on plan exc 6 m mean radius built in cement mortar (1:6) complete all as specified. (using old size bricks)

Returning filling in, including spreading, leveling and watering, well ramming n.exc 25cm thick layer in soil complete all as specified and directed.

Removing excavated material (Soils) to a distance not exceeding 50 mtr and depositing where directed at a level n.exc. 1.5 mtr above the starting point complete all as specified and directed.

M&L, Moorum/red bajri filling in floors or paving, laid in layers n exc 15 cm thick, spread, levelled and rammed including watering etc complete all as specified and directed by Engineer- in- Charge

M&L, Sand filling under floors or in foundation incvluding watering and consolidation etc complete all as specified and directed by engineer- in- charge

M&L for hard core of broken stone or boulder of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc. 15cm thick, watered and well rammed to a true surface complete all as specified and directed.

M&L for providing 100mm thick cement concrete (1:4:8) Nominal Mix (using 40mm grade stone aggregate) as in sub floor, sub base of floor complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 type B-1 using 20mm graded aggregate as in flooring, finished even and smooth using extra cement, laid in alternate bays nexc 4sqm and divided in to glass dividing strips, complete all as specified.(Glass dividing strip shall be measured and paid separately)

M&L for rendering 15mm thick in cement mortar 1:4 in two layers (10-12 & 5-3 mm thick)on walls (fair / unfair finished faces of brick/concrete), finished even and smooth without using extra cement complete all as specified. (Water proofing compound where ever required , will be measured and paid separately under respective item of BOQ)

M&L for rendering 10mm thick in cement mortar 1:4 as on ceiling (fair finished concrete faces) finished even & smooth without using extra cement complete all as specified.

Supply only integral water proofing compound complete all as specified and directed.

M &L 15 mm thick rendering in cement mortar (1:6) in two layers (10-12 & 5-3 mm thick) on fair faces of brick work and finished even and smooth without using extra cement complete all as specified and directed.

M&L for forming fair finished drain or channel 45cm inner girth in cement concrete, using extra cement including forms, moulds, mitered/ stopped ends etc complete all as specified and directed.

M&L for mild steel framed work such as grills, gratings , iron chowkhats etc., framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work mild steel conforming to Fe - 290, Gde- E 165 complete all as specified and directed.

S&F steel windows with side hung shutters including box type hinges with MS handles and tower bolts, peg stay etc complete with glazing bars dovetailed or welded with one shop coat of primer complete all as specified and directed.

S&F steel windows with side hung shutters including box type hinges with MS handles and tower bolts, peg stey etc complete without glazing bars, as fly proof shutters with one shop coat of primer complete all as specified and directed.

S&F steel ventilator with top hung shutters including box type hinges with MS handles and tower bolts, peg stey etc or suitable fittings, complete with/without glazing bars, with one shop coat of primer complete all as specified and directed with guard bars/ grills.

S&F steel windows or ventilatrs, fixed type without glazing bars complete all as specified and directed.

S&F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with m s screws, or galvanised wire staples complete all as specified and directed.

M&L for sheet glass ordinary quality 4mm thick and glazing with oil putty in squares n.exc. 0.5 sqm each pane complete all as specified and directed.

M&L for 25 mm thick cement concrete (1:2:4) type B-1 (using 12.5 mm graded stone aggregate) as in sub base/ floor for laying floors, tiles etc, finishing the surface fair and even complete all as specified and directed .

M&L for 20-25 mm thick machine cut kota stone slab of as in flooring edge cut, one colour, over & including 20mm thick screed/bedding layer in CM (1:6), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed.

M& L for 15-18mm thick Kota stone tiles (Pre-mirror polished), in riser of steps, skirting, etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles including rounding the edges of kota stone over and including 10mm thick backing coat in cement mortar (1:3), surfaces finished even and rough to receive tiles, complete all as specified and directed.

M&L, applying three coats white washing on walls with preparing new plastered surfaces complete all as specified & as directed

M&L, applying three coats white washing on ceilling surface including preparing new plastered surfaces complete all as specified & as directed

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint of approved shade on walls over a coat of suitable primer complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of new untreated steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L 40 mm thick in cement concrete type B- 0 (1:2:4) using 12.5 mm graded stone aggregates in Damp proof course to horizontal or vertical surfaces including necessary form work complete all as specified.

S&F 200 mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F mild steel butt hinges cold rolled medium weight 100mm size complete alla specified and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) complete all as specified and directed.

S&F 300 mm, MS ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

S&F 150 mm long, extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed.

S&F 100 mm long stainless steel butt hinges, including taking down old one complete all as specified and directed.

Supply, fixing, laying & testing 15 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Supply, fixing, laying & testing 25 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Supply, fixing, laying & testing 20 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M&L for water proofing treatment on roof slab including picking, sweeping clean and washing down with water to remove dust & providing water proofing treatment described as under:- (a) Surface preparation and treating of construction joints, filling of honey combs with polymer modified mortar (Cement: Sand : smart care multipurpose polymer of Asian Paints or equivalent product of Thermax/ Berger ) (b) Providing PCC (1:2:4) type B-0, 25 mm thick levelling/padding layer over roof surface .

Item No 59.00 contd-. (c) Cleaning the surface and applying (Resin & Hardner) smart care Epoxy Primer 2k of Make Asian paints or equivalent product of Thermax/ Berger ) on the cleaned surface for bonding of PU magnum with the existing concrete surface. (d) Supplying, providing and applying waterproofing treatment to Terrace area with Asian Paints Smart care PU magnum, single component highly elastomeric seamless cold applied modified PU coating or equivalent product of Thermax/ Berger) including all necessary surface preparation, coving using smart care multipurpose polymer, water pond test, etc. complete as per manufacture's specifications and application methodology. The same coating shall be applied in two coats achieving a total thickness of 1mm. The coating shall have dual combination of 250% elongation . Execution to be done with authorised applicator of the manufacturer. Work will be executed in smart assurance system..

S&F powder coated aluminium door with frame and shutter and glazing 5 mm thick tinted glass and 12 mm thick prelaminated particle board exterior grade in bottom panel, rubber gasket, aluminium beading, aluminium glazing clips, mortice lock, aluminium stopper cleat, iron mongary etc. section of aluminium door shall be of following sizes:- Frame : 85 x 44.5 x 1.2 mm thick fixed with rawal plug Middle lock rail: 85 x 44.5 x 1.2 mm thick Bottom rail : 112 x 44.5 x 1.2 mm thick Top rail / Style: 85 x 44.5 x 1.2 mm thick Glazing beading: 0.70 mm thick Aluminium handle 'D' type: 150 mm Aluminium tower bolt 9.9 mm dia shoot 200 mm long Mortice lock – 100 mm 4 lever, hydraulic door closer -01 No per leaf , Aluminium stopper cleat ,Stainless steel but hinges 100 mm size-4 Nos per leaf

M & L for brickwork with sub-class `B` bricks,old size, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge

M&L pre polished coloured machine pressed precast rubber moulded concrete interlocking paver block any shape and size fixed with gray cement and pigment confirming to IS15658-2006 of 60mm thickness M-35 grade all as specified and directed.

M&L for coloured non skid ceramic joint free tiles (Square/ rectangular) of 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.06sqm but not exceeding 0.11 sqm , in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed 15mm thick in CM 1:6 complete all as specified and directed .

M&L for glazed ceramic coloured tiles 450x300x7 mm as in dado/ skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles including 10mm thick rendering in CM (1:4) for receive tiles complete all as specified and directed.

M&L for PCC (1:3:6) type C-2 (using 40mm graded curshed stone aggreate), 75 mm thick as in plinth protection, finishing the surface even & fair without using extra cement the plinth protection shall be laid in alternate bays n exe 2 Sqm, 10mm joints shall be provided, joints shall be filled with bitumen mastic, bitumen mastic comprise of 1 Part of Hot bitumen 85/25 grade and 3 parts of sand all by weight complete all as specified & directed.

S & F of rolled mild steel sections as in roof trusses (framed) trussed purlins, crane gantries rails fastening and heavy brackets framing (beam TEE angle channel or flat sections ) includin distance pieces, cleats etc including cutting welding etc conforming to Fe -410-W (Gde E 250 ) quality B complete all as specified and directed.

M&L for Pre-painted Galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick, of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified.

S&F Pre-painted galvalume aluminum zinc coating GI based profile ridge line,, 0.50mm thick ,having tensile strength of 550 Mpa as in roof ridge , fixed with self tapping screws, suitable for corrugated pre painted GI based roof steel sheets complete all as specified and as directed

S&F factory made 100% solid wood plastic composite (WPC) door frame of size 75 mm x 50 mm x 50 mm made from wood plastic composite (single extruded process) material with density 780 Kg/Cum from ISO certified company door should be water proof termite proof fire retardant and having good screw holding capacity all as specification and drawing complete all as specified and directed by Engr-in-Charge. Make : ECHON/Kumar Tech/Sintex

S&F 30 mm thick moulded WPC factory made 100% solid door shutter(conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side palin with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire retardant and having screw holding capacity complete all as specified. Make : ECHON/Kumar Tech/Sintex

S&F half stall vetrious china urinals (wall type), including CP brass 32mm waste fitting with long screwed shank and fly-nut, 32 mm PVC waste pipe, bedding urinal to walls with and incl 60 mm long brass screws, pointing around urinal back in white cement complete all as specified. . Make :Jaquar/URS-WHT- 13261 size 355x340x535/ Hindware vinezia Cat Part No 60012 Stan white padestal size 31.5x34.5x66cm/ Parryware Cat Part No EWHIZ size 360x345x565.

S&F for 15mm dia PVC connection 450mm long complete all as specified and directed by Engr-in-Charge.

S&F vitreous china wash hand basin with brackets, white, size 550 x 400 mm including CP brass 32mm waste fitting with long screwed shank and fly-nut, 32 mm PVC waste pipe including cutting for and pinning in ends of brackets complete all as specified. Make: Jaquar CNS WHT 801/ Parryware CO460/ Hindware 10010

S&F 15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed by Engr-in-Charge.Make : Jaquare Cat Part No VGP 81001/Hindware Cat Part No F370001/Parryware Cat Part NoG9802A1

S&F 15mm bore Angle Stop valve, cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed. Make: Jaquar Cat Part No FON-40053/ Hindware Cat Part No F160017/ Prayag Cat No 9410.

S&F 30 mm thick moulded WPC factory made 100% solid door shutter(conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side palin with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire retardant and having screw holding capacity complete all as specified. Make : ECHON/Kumar Tech/Sintex

S & F 20 mm dia brass chromium plated towel rack of 3 sets type 60cm long between flanges including pair of fixing brackets complete all as specified and directed. Make: Jaquar Cat Part No AKP-35781PS/CAN-1181FHS

S&F brass CP towel ring 200mm dia and 8mm thick solid fixed with CP steel screw complete all as specified and directed. Make: Jaquar cat No- ACN-1121 BN/ Prayag cat No-BA-11/ equivalent in Hindware/ Parryware.

S & F acreylic glass corner shelf with CP brass railing size 300 mm long and fix to wall with rawl plug and CP screws complete all as specified and directed. Make: Jaquar cat No- ACN-CHR-1173 / Prayag cat No-BEA-44/ equivalent in Hindware/ Parryware.

S&F looking mirror of size 1200x600mm x5.5 mm thick glass, fancy type bevelled and fixed stainless steel clamps SS 304 grade ,complete all as specified and directed, design and make shall approved by GE.

S&F gun metal globe or gate valve of size 15 mm dia with iron wheel head screwed both ends and for iron pipe & fixed, ISI marked, complete all as specified and directed.

S&F gun metal globe or gate valve of size 20 mm dia with iron wheel head screwed both ends and for iron pipe & fixed, ISI marked, complete all as specified and directed.

S&F 20mm bore ball brass valves, high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks 1000 Ltrs capacity three layered, externally white (cylindrical vertical with closed top) hoisted and fixed in position including PTMT ball valve 20mm bore with polythelene float, 20mm dia GI medium grade over flow pipe(approx lengh1.5 mtr), 25 mm dia wash out pipe with pluged at one end complete all as specified and directed.

S&F 75 mm dia cast iron floor trap, with CP grating including jointing to waste pipe with cement and fixed in cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) complete all as specified and directed.

M&L for 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed. Make : Supreme/ Finolex

M&L for 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed. Make : Supreme/ Finolex

M&L for pre-polished pavement coloured chequred rubber moulded tiles glossy finish of size not less than 300x300x20-22 mm thick with antI skid properties laid over and including 20mm thick screed bed in CM (1:6) complete all as specified and directed.

S&F brass chromium plated ovehead shower with shower arm complete all as specified and directed. Make : - Parryware Cat Part No T9985A1(Shower) & T-9999A1(Arm)/Hindware Cat Part No F160054 (Shower) & F190016(Arm)/Jaquar Cat Part No OHS 1999 (Shower) & SHA479L300 (Arm).

S&F CP 101x101mm Square shape grating including cockrotch jali complete all as specified and directed.

S&F CP bathing spout with wall flange 15 mm bore fancy type cromium plated scrwed down, screwed for iron pipe or for brasss ferrule fixed complete all as specified and directed. Make : - Jaquar SPJ-15429PM/SPJ-10429PM or equivalent kohler.

S&F concealed body for joystic diverter 40 mm cartridge with button assembly (button on top) but without exposed part. Make: Jaquar ARC-87065C or equivalent Kohler and single liver exposed part kit of diverter consisting of operating liver wall flange (with seal and button only) Make: Jaquar OPP 15065KPM or equivalent Kohler PGD 10879 IN.

S&F of bottle trap of chromium plated (half of full threaded) complete all as specified and directed by Engr-in-Charge. Make : Hindware Cat Part No F850004/ Prayag Cat Part No BEF-21/12"/ ALD -769L250x190

M&L for Point wiring with 1100 Volts grade 1.5 Sqmm (nominal area) PVC insulated but unsheathed multistranded copper conductor single core FRLS cable and 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable green colour as earth wire upto common earth and connected to earth dolly, drawn through and including non metallic medium duty rigid PVC concealed conduit (medium duty) 20mm dia or higher size complete with all accessories such as socket, elbow, junction box, bell mouth, bend, reducer etc including pressed steel junction box of thickness 1.2mm for mounting of switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet as top cover, complete all as specified and directed by Engr.-in-charge of following. Note:- Wire/cable colour coding shall be maintained properly as per IE rule. (Make of conduit & accessories- Precision/Polycab/AKG, Make of wire- Polycab/L&T/KEI)

(a) One light point/ bell buzzer point controlled by one, one way switch

(b) One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

All as per item No.94.00 above here in but with 2.5 Sqmm (nominal area) wire/cable for phase & neutral for one 3 Pin 15 amp socket on independent board including one 2.5 sqmm PVC insulated unsheathed multi stranded copper conductor cable FRLS,1100 volts grade as earth continuity conductor upto common earth & connected to earth dolly complete all as specified and directed by Eng.-in-charge.

S&F of switch piano flush, button type 5 Amps SP complete all specified.

S&F of switch piano flush button type 15 Amps SP complete all as specified & directed.

S&F of socket outlet multipurpose 3 pin 5 amps and 2 pin 5 amps, complete all as specified and directed.

S&F socket outlet two in one three pin 5 Amp and 15 Amp flush type complete all as specified and directed.

S&F ceiling rose surface bakelite 3 terminals of size 65x25mm. complete all as specified & directed.

S&F lamp holder,pvc/polycarbonate type with back platesuitable for batten fittings complete all as specified & directed.

S&F sheet metal enclosures 240 volt with suitable rated bus bar for double door 8 way IP-43DB's suitable for one MCB SPN as incoming and 6 MCB SP as out going, mounting flush on wall and making good disturb surfaces complete all as specified and directed by Engr-in-charge (MCB shall be measured and paid separately) Make:- Legrand /ABB/Schneider

S&F MCB, DP 240 volt, 10 KA, 40 Amp, 'B' curve conforming to IS complete all as specified and directed. Make:- Legrand /ABB/Schneider

S&F MCB single pole 240 volt, 10 KA, 6-32 Amp, 'B' curve conforming to IS complete all as specified and directed. Make:- Legrand /ABB/Schneider

S&F wall mounted tube light fitting 1x20/22 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 6500K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed. Make:Philips Cat Part No TMC 501P1xT LED 22WP-3241(tube batten) and MAS LED 1200mm 18W-865-T-81 (tube)/ Wipro Cat No WI0922208 (Tube Batten) LL13-181-65SE (tube) / Havells Cat Part No LUMILINEPLUSBS20WLE86SPCSS (tube Batten ) CRYSTAL 1213T8DSTL20WELD865SGLASS (tube double side)

S&F high efficiency LED bulbs 1 X 12 watt pin type direct fit in holder complete all as specified and directed. Make :- Havells/Phillips/SURIYA ROSHNI.

S&F exhaust fan metalic body complete with louver 230V, single phase 300mm sweep including connecting with three core 23/0076 copper wire from ceiling rose to fan complete all as specified and directed. Make: Havell/ Crompton/ Usha

M&L Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level, earth plate surrounded by and packed with a 15 cm thick layer of char coal dust and common salt, earth lead GI wire 4.00 mm. dia by means of bolts, Nuts, Check Nuts and washers of galvanized iron and thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe medium 15 mm. bore, and water pipe 20 mm. bore GI light grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 & 75 mm thick RCC (1:2:4) type B1 cover slab reinforced with 8mm TMT bars 100mm c/c both ways complete all as specified & shown in elect plate No. 3 of SSR part I of 2009 and testing on completion. (Note:- (i) If the desired earth resistance is not found within permissible limit shall be redone by the contractor at no extra cost. (ii) Cost of GI wirre 4 sqmm and 15mm dia pipe medium grade upto 7.5 mtr is included in the rate quoted for this item).

Supply, laying & connecting XLPE insulated armoured, heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 10 Sqmm 2 core including fixing lugs, cable gland etc including bare conductor duly insulated with Pvc heat shrinkable sleeve 1.1 KV grade at both end complete all as specified and directed .

Supply & Laying well burnt bricks, sub class 'B' brick laid breadth wise, along the cable in trenches after sand cushioning laid for protection of UG cable protection complete all as specified and directed.

M&L for sand cushioning in trenches for protection of UG cable with river bed sand laid dry in trenches before and after laying of cable, including well ramming and consolidation complete all as specified and directed. (Punned thickness shall be measured)

S&F for integral LED street light luminaire comprising of pressure die cast aluminum housing heat resistant toughened glass with fram IP-65 protection road way luminaries with high power LED 40/45 watt with efficiency 100 lument/ watt at system level, CCT>5700K, with average life class 50,000 buring hours, , complete all as specified and directed. Make: Crompton model No LSTP-45-CDL/ Havells Model No ENDIRAPEARLNEOSL 40WLED757PASYTOPC/ Philips Cat Part No BRP409LED CW036MRFGIPSUGR and Syska SSK-ST-40W.

M/S Electrotech Sales