Construction of residential building under Jal Shakti Circle, Bilaspur in Tehsil Sadar District Bilaspur (SH Construction of 3 Nos. type-III quarters at Changer Sector Bilaspur).

Amount

Excavation in foundation and trenches (for pipe and pits) in all kinds of soil such as pick jumper work, including saturated soil stacking the excavated soil with all leads and lifts and clear from the edge of excavation and then returning the stacked soil in 15cm layers, when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed within all leads and lifts including dressing of beds and sides and preparation of un metal led /metal led/ paved surfaces to its original conditions including shoring, strutting, timbering and dewatering whenever is required. Providing diversions for traffic, night signals fixing caution board crossing over trenches for access to houses complete in all respect and to the entire satisfaction of the Engineer-in-charge Pick and jumper work.

Providing and laying cement concrete 1:4:8(1cement:4sand:8 graded crushed stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of materials in all leads and lifts.

Providing and laying cement concrete work 1:1½:3(1cement:1½sand: 3 crushed stone aggregate 20mm nominal size & curing complete excluding the cost of form work and reinforcement for reinforced concrete work in following items including carriage of material in all leads & lifts.

Foundation footings base of columns and the like and mass concrete and to the entire satisfaction of the Engineer-in-charge.

Column, pillars,posts and struts upto floor two level in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Floor two level to floor three levels and to the entire satisfaction of the Engineer-in-charge.

Floor three level to floor four level and to the enitre satisfaction of the Engineer-in-charge.

Suspended floor roofs landing shelves and their supports balconies, beams girders bressumers and cantilevers up to floor two level.

Floor two level to floor three levels and to the entire satisfaction of the Engineer-in-charge.

Floor three level to floor four level and to the enitre satisfaction of the Engineer-in-charge.

Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finihsing of nosing upto floor two level and to the entire satisfaction of the Engineer-in-charge.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centering shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centering below supporting floor two ceiling not exceeding 4 mtr and removal of the same for in-situ reinforced concrete and plain concrete working:-

Foundation footings base of columns and the like and mass concrete and to the entire satisfaction of the Engineer-in-charge.

Flat surfaces such as soffits of suspended floor landings and the like up to 200mm thickness and to the entire satisfaction of the Engineer-in-charge.

Columns, pillars, posts and struts Square, rectangular or polygonal in plan and to the entire satisfaction of the Engineer-in-charge.

Stair cases with sloping or stepped soffits excluding landing and to the entire satisfaction of the Engineer-in-charge.

Beams, cantilever, girders and lintels and to the entire satisfaction of the Engineer-in-cahrge.

Edges of slabs and breaks in floors and walls: Under 20 cm. wide and to the entire satisfaction of the Engineer-in-charge.

Providing laying of tor steel reinforcement for RCC work including bending binding and placing in position complete in all depths and heights and to the entire satisfaction of the Engineer-in-charge.

Providing and laying 20 cm thick composit stone masonry with stone facing of chisel dressed stones one linedressed in cement mortar 1:6 (1cement: 6sand) and concreete backing with cement concrete 1:3:6 (1cement: 3sand: 6 graded stone agg. 20mm nominal size) on inner face of walls including centring,shuttering and propoping complete upto floor (EXTERIOR WALLS)

2nd class brick work using common burnt clay building bricks in supper structure above plinth upto floor two level in cement mortar 1:6(1cement:6sand) including carriage of materials in all leads & lifts and to the entire satisfaction of the Engineer-in-charge.

2nd class Half brick masonry in common burnt clay building bricks in :Cement Mortar 1:4(1 Cement : 4 Sand) including carriage of materials in all leads & lifts.

Providing wood work of 2nd class deodar wood in frames of doors,windows,clerestory,windows and other frames wrought, framed and fixed in position complete including carriage of materials in all leads & lifts and to the entir satisfaction of the Engineer-in-charge.

Providing and fixing panelled glazed or panelled and glazed shutters for doors,windows and clerestory windows i/c bright finished/black enamelled iron butt hings with necessary screws 2nd class deodar wood 40mm thick including carriage of material in all leads & lifts and to the entir satisfaction of the Engineer-in-charge.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws 2nd class deodar wood 40mm thick including carriage of material in all leads & lifts and to the entire satisfaction of the Engineer-in-charge.

15mm cement plaster in single coat on rough side of brick/stone masonry for interior plastering upto floor two level i/c arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 20mm in girth and finished even and smooth cement mortar 1:6 including carriage of material in all leads & lifts and to the entire satisfaction of the Engineer-in-charge.

20mm Cement plaster in single coat on rough side of interior plastering upto floor two level ncluding arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:4 including carriage of material in all leads & lifts and to the entire satisfaction of the Engineer-in-charge.

Providing and laying granite stone in flooring 20mm(average)thickness base of cement mortar 1:3 (1cement:3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete including carriage of material in all leads & lifts and to the entire satisfaction of the Engineer-in-charge.20mm.thick(for stairs and top of kitchen shelf)

Providing and fixing 10mm thick antiskid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 600x600mm/600x1200mmx10mm manufactured of approved shade and colour inflooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) ointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of material in all leads & lifts and to the entire satisfaction of the Engineer-in-charge. (13680000)(As per sample approved by Department)

Providing and laying spartic ceremic tiles 5.5mm.thick in flooring (600 x600mm. size)treads of steps laid on a bed of 12mm. thick cement mortar 1:3(1cement:3 sand) finished with flush pointing in white cement including carriage of material in all leads & lifts and to the entire satisfaction of the Engineer-in-charge.

Kota stone slab flooring 20 mm (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. including rubbing and polishing complete including carriage of material in all leads & lifts. (13540200) 30 mm thick.for Porch area.

White glazed tiles 6 mm thick in dado of toilets,corridores etcflooring, treads of steps and landing laid on a bed of 12 mm thick cement mortar 1:3(1 cement :3sand) finished with flush pointing in white cement complete in all respect including carriage of material in all leads & lifts and to the entire satisfaction of the Engineer-in-charge. (13210000).(size of tile=30x45cms

Providing and fixing bright finished MS sliding door-bolts with nuts and screws etc. complete in all respect including carriage of material in all leads & lifts and to the entire satisfaction of the Engineer-in-charge (250x16mm

Providing fixing bright finished MS tower bolts (barrel type) with screws etc. complete. in all respect including carriage of material in all leads & lifts.

Providing and fixing bright finished MS handles for doors with screws etc. complete. in all respect including carriage of material in all leads & lifts and to the entire satisfaction of the Engineer-in-charge.

Providing and fixing bright finished hard drawn stainless steel hooks and eyes complete in all respect including carriage of material in all leads & lifts and to the entire satisfaction of the Engineer-in-charge . (1212204000) 150 mm

Providing and laying cement concrete 1:6:12(1cement:6sand:12 graded crushed stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth ( under Floor) complete in all respect including carriage of materials in all leads and lifts and to the entire satisfaction of the Engineer-in-charge .(under flooring)

Providing and fixing 40x3mm flat iron hold fast 40 cm.long including fixing to frame with 10mm diameter bolts,nuts and wooden plug and embedding in cement concrete block 30x10x15cm of 1:3:6 (1cement:3sand:6graded stone aggregate 20mm nominal size)complete in all respect including carriage of material in all leads and liftsand to the entire satisfaction of the Engineer-in-charge

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting,fixing in position and applying a priming coat of red lead paint. In beams joists channels ,angles, tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like complete in all respect including carriage of material in all leads and lifts and to the entire satisfaction of the Engineer-in-charge

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees including carriage of material in all leads and lifts as required as per the direction of Engineer-in-charge (14550000).

Providing and fixing ridges or hips 60cm overall with 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories including carriage of material in all leads and lifts as required as per the direction of Engineer in Charges (14560000).

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm nominalsize) complete in all respect including carriage of material in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Stone filling behind retaining walls and under floors complete in all respect including carriage of material in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.(1133000000).

Filling in plinth with sand under floors including watering ramming consolidating and dressing complete under flooring complete in all respect including carriage of material in all leads & lifts and to the entire satisfaction of the Engineer-in-cahrge.

Providing and fixing bright finished brass handles for cup board with screws etc. complete. in all respect including carriage of material in all leads & lifts and to the entire satisfaction of the Engineer-in-charge.. 150 mm

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete in all respect including carriage of material in all leads & lifts and to the entire satisfaction of the Engineer-in-charge.

Applying one coat of Acrylic primer (Spectrum or equivalent of Superior quality) on new concrete/ masonry/plastred surfaces after and including preparing the surface by thoroughly brushing the surface free from mortar droppings and other foreign matters, sand papering the surface smooth complete complete in all respect including carriage of material in all leads & lifts and to the entire satisfaction of the Engineer-in-charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete in all respect including carriage of material in all leads & lifts and to the entire satisfaction of the Engineer-in-charge.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including t horoughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface complete in all respect including carriage of material in all leads & lifts & and to the entire satisfaction of the Engineer-in-charge.

Applying one coat for wood preservetive on previously treated wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil,grease,dirt and other foreign matter,sand papering and knotting complete in all respect including carriage of material in all leads & lifts & to the entire satisfaction of the Engineer-in-charge.wood filler transparent)

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting.complete including carriage of material in all leads & lifts & to the entire satisfaction of the Engineer-in-charge Readymixed paint brushing with pink for priming

Painting two coats(excluding primimg coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping complete in all respect including carriage of material in all leads & lifts & to the entire satisfaction of the Engineer-in-charge other than white enamel paint

Painting two costs (excluding priming coat) on new steel and other metal surfaces with enamel paint brushin to give an even shade including cleaning the surface of all dirt,dust and other foregin matters complete including carriage of material in all leads & lifts & to the entire satisfaction of the Engineer-in-charge Enamel white paint

Providing and laying heavy duty precast cement conrete inter locking paver blocks vibro compacted upto M-50 grade i/c border or kurb block grey or coloured over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete (Sub base concrete floor to be paid for 60mm thick inter locking blocks complete in all respect including carriage of material in all leads & lifts & to the entire satisfaction of the Engineer-in-charge.

Constructing course rubble hammer dressed ‘U’ shape open surface drain with side wall,15x22cm in cement mortar 1:6 (1cement: 6sand) and inside plastering with cement plaster 1:3 (1cement: 3sand) incuding earth work and laying 10cm cement concrete in 1:5:10 (1cement:5 sand:10 graded stone agg.) of 40mm nominal size and 7.5cm cement concrete 1:2:4 (1cement:2sand: 4 graded stone agg. of 20mm nominal size and finished with a floating coat of neat cement concrete as per standard design and to the entire satisfaction of the Engineer-in-charge.

Add lump sum provision for structural design, drawing and bearing capacity of soil and to the entire satisfaction of the Engineer-in-charge.

ELECTRIAL ITEMS

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. Group-C

Wiring for light plug with 2x1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Supplying & fixing of G.I. modular boxes of following sizes along with modular base and cover plate for modular switches in recess as required:-

4 modules(140mmx78mmx50mm)

6 modules(205mmx78mmx50mm)

8 modules (120mmx135mmx60mm)

12 modules (205mmx135mmx60mm)

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.

2x1.5 Sq. mm.

2x2.5 Sq. mm.

Wiring for circuit / sub-main with 4x6 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.6 Sq.mm. (4x6+2x6) HRFRLS/PVC insulated single core copper conductor cable for earthing wire from MCB box to main pannel board.

Wiring for circuit / sub-main with 4x10 Sq. mm. PVC insulatedheat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.10 Sq.mm. (4x10+2x10) HRFRLS/PVC insulated single core copper conductor cable for earthing three phase wiring in main pannel board for busbar.

Supplying and fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

S.P. 5/ 6 Amps one way Modular switch.

5 pin, 5/ 6 Amps Modular socket outlet.

Bell push, Modular.

Supplying and fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

S.P. 15/ 16 Amps one way Modular switch

6 pin,15/16 Amps Modular socket outlet.

Supplying and fixing TV. Socket outlet, modular rating switch /socket in the existing switch box / cover plate including connections etc. as required.

Supplying and fixing ceiling rose on the existing junction box /wooden block including connections etc. as required.

Supplying and fixing of Double door-12 way single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wireset, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnec- tions, phosphatized and powder painted, including earthing etc. as required.

Supplying and fixing 63 Amps. Cat-A rating, four pole (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing sheet metal bus-bar chamber suitable for 200 Amp. 415 volts capacity with 4 No. copper strip bus-bars each of length 450mm & cross-sectional area(25.4mmx4.75mm), enclosure made from 1.6 mm thick M.S. sheet having overall dimensions (530mmx450mmx 150mm) nominal with all accessories including connections, earthing the body etc. as required.

Providing and fixing TP&N switch disconnector fuse unit cubical type, 415/500 volts with 3 No. HBC/HRC fuses, in sheet steel enclosure including drilling holes on the board, connections, earthing the body etc. as required. 100 Amp. Category-A

Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of Single pole & neutral. Cat-B in the existing MCB DB complete with connections etc. as required:-

Supplying and erection of wall mounted metal boards for switch gear mounting of suitable size, with permissible variation in size of plus minus 5mm, welded frame work made of M.S. angle iron 35 mm x 35 mm x 6 mm thick duly welded complete with 2.80mm thick M.S. sheet fixed with hinges as open able front, complete with locking arrangement including painting and bonding to the existing earth as required:-

Supplying and erection of 40/50/63 amps rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of Double pole. Cat-B in the existing MCB DB complete with connections etc. as required:-

Supplying and fixing 40 Amps. Cat-B rating, four pole (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 Amps, 240 volts, SPN industrial socket outlet, 2-pole & earth, metal enclosed plug top, sheet steel enclosure, suitable to accommodate a 20 Amp SPN-MCB/DP,on surface or in recess, with chained metal cover for the socket outlet, complete with connections, testing and commissioning etc. as required.

Providing and fixing TP&N switch disconnector fuse unit panel mounting, 415/500 volts with 3 No. HBC/HRC fuses, open execution, including drilling holes in the cubical, making connections, etc. as required. 200 Amp. Category-A

Earthing with copper earth plate 600 mmx600 mmx 3 mm thick, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required.

Extra for using salt and charcoal for G.I. or copper plate earth electrode complete as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia. 300 mm long copper tube, having single prong at top, with 85 mm dia 3 mm thick copper base plate including holes etc. complete as required.

Supplying and fixing copper tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as required ( for vertical run)

Supplying and fixing copper tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as required ( for horizontal run)

Providing and fixing M.V.danger notice plate of 200 mm x 150 mm made of mild steel at least 2 mm thick, and vitreous enameled white on both sides and with inscription in signal red color on front side as required.

Providing and laying of one No. aluminium conductor, PVC insulated and PVC sheathed, Armoured/ XLPE power cable, working voltage 1100 volts grade direct in ground; to be laid 1 meter below the ground level including excavation sand cushioning, protective covering and refilling the trench etc. of the Armoured cable 4 sq. mm (twin core) for Yard lights.

Providing and installation of stationary storage type Electric water heater (Geyser) of various sizes by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and fixing of Nonreturn valve, Dead weight safety valve, 2 No C.P. connection rods 18" long, making good the damages, electrical connections, safety valve connections, testing and commissioning etc. 25 Liter capacity water heater (Cat-A)

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. Ceiling Fan 1400 mm sweep, Category-A

Providing and installation of Exhaust Fan, Light duty, (Domestic) 225 mm sweep in the existing opening, including taking the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc.

Providing, Installation, testing and commissioning of tube fitting 1x20W LED complete in all respect.

Providing and fixing Mirror light 60 cms long 6 watt LED fixture.

Supplying and fixing Ding-Dong / Electronic musical bell, suitable for D.C./A.C. single phase,230 volts complete as required

Supplying and fixing 9 watt.LED bulbs.

Supplying and drawing co-axial TV cable,RG-6 grade,0.7mm (75 Ohms) copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface / recessed, steel / PVC conduit as required.

Supplying and fixing bakelite batten/angle holder including connections etc. as required.

Supplying and fixing stepped type Modular fan regulator on the existing modular box including making connections etc. as required.

SANITARY / WATER SUPPLY ITEMS

Providing and fixing high pressure PVC.spigot and socket waste ventilating pipe of following dia meter i/c entire carriage of material within all leads and lifts.minimum 6 kg pressure

75mm dia

110mm dia

Providing and fixing PVC plain bend of following diameter i/c entire carriage of material within all leads and lifts.

75mm dia

110mm dia

Providing and fixing PVC door bend of following diameter i/c entire carriage of material within all leads and lifts.

75mm dia

110mm dia

Providing and fixing PVC collar/ socket of following diameter i/c entire carriage of material within all leads and lifts.

75mm dia

110mm dia

Providing and fixing PVC Single equal brach of following diameter i/c entire carriage of material within all leads and lifts.

75mm dia

110mm dia

Providing and fixing PVC Single equal brach with eval access of following diameter i/c entire carriage of material within all leads and lifts.

75mm dia

110mm dia

Providing and fixing PVC Floor traps 110x75mm i/c entire carriage of material within all leads and lifts.

Providing and fixing viterous China wash down water closet (European Type WC pan) with intergral “P”or”S” trap including jointing the trap with PVC soil pipe ,including cistern and seat cover) including entire carriage of material within all leads and lifts.

Single piece WC .300 mm wall distance Jaquar/Cera make.

Providing and fixing vitreous china wash basin with single hole mixture with CI or MS brackets painted white i/c cutting holes & making good the same but excluding fitting i/c entire carriage of material within all leads and lifts. Cera /Jaquar make Concord, 630x450mm size.

Providing and fixing vitreous china pedestal for wash basin complete recessed at the back for the reception of pipes and fitting i/c entire carriage of material within all leads and lifts.

Providing and fixing of MI union for wash basin 32mm dia i/c carriage of material within all leads and lifts.

Providing and fixing 32mm dia PVC waste pipes for wash basin i/c brass check nut i/c entire carriage of material within all leads and lifts.

Providing and fixing 900x600 mm bevelled edge mirror of superior glass mounted on 6mm thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washer including carriage of materials within all leads and lifts.

Providing and fixing C.P. brass towel rail complete with C.P.brass brackets fixed to wooden plugs with C.P. brass screws including carriage of materials within all leads and lifts 600 x 20mm. Jaquar make

Providing and fixing 600x120mm glass shelf i/c entire carriage of material within all leads and lifts.Jaquar make

Providing and fixing CP brass soap dish i/c entire carriage of material within all leads and lifts.

Providing and fixing Tooth brush and tumbler holder i/c entire carriage of material within all leads and lifts.

Providing and fixing CP brass shower 300mm dia and 60 cms long rod i/c entire carriage of material within all leads and lifts.

Providing and fixing brass bib tap long nose 15 mm dia (Heavy duty) i/c entire carriage of material within all leads and lifts.(Kitchen sink)

Providing and fixing CP brass wall mixture for bathing area.

Providing and fixing CP brass angle valve 15 mm dia without nut and pipe i/c entire carriage of material within all leads and lifts.

Providing and fixing CP concealed stop cock 15 mm dia without nut and pipe i/c entire carriage of material within all leads and lifts.

Providing and fixing single hole single lever wash basin mixture i/c entire carriage of material within all leads and lifts.Jaquar make

Providing and fixing PVC connection 15mm dia i/c entire carriage of material within all leads and lifts.

Providing and fixing 100mm dia, C.P. brass grating including carriage of material within all leads and lifts.

Providing and fixing Health facut (hand shower) fixed for WC seat i/c entire carriage of material within all leads and lifts.

Providing and fixing CP towel ring i/c entire carriage of material within all leads and lifts.

Providing and fixing wall to ceiling and floor galvanised mild steel tubes light grade), tube fittings and clamps i/c making good wall ceiling & floor of following diameter i/c entire carriage of material within all leads and lifts

15mm dia

20mm dia

Providing & fixing Brass full way ball/handel type wheel valve i/c entire carriage of material within all leads & lifts

15mm dia

20mm dia

Providing and fixing 115x50x25cms size double bowl of approved make stainless steel kitchen sink i/c entire carriage of material within all leads and lifts

Providing and fixing 1000 ltrs. Double layer sintex make water storage reservoir with top lid and making connection complete in all respect including all leads and lefts.

Constructing manhole with RCC top slab in 1:2:4 mix ( 1 cement :2 sand:4 graded stone aggregate 20 mm nominal size) foundation concrete 1:4:8 ( 1cement:4sand :8graded stone aggregate 20 mm nominal size),inside plastering 15 mm thick with cement mortor 1:3 (1cement:3sand),finished with a floating coat of neat cement & making channels in cement concrete 1:2:4 (1cement:2 sand:4 graded stone aggregate 20mm nominal size) finished smooth complete i/c curing &testing. (i) inside size 1200 x 900 x 1000 mm deep i/c c.i. cover with frame (m. duty) with single pattern 455 x 610 mm internal dimensions (total wt.of cover & frame to be not less than 38 kg) 23 cms. thick brick masonry walls using 2nd class brick in cm 1:3 (icement : 3 sand)

Providing & fixing stone ware gully trap grade 'A' complete with CI grating,B/Masonry chamber in cement mortor 1:5 & water tight CI cover with frame of 300 mm x 300 mm size (inside) .The wt.of cover to be not less than 4.53 Kg & frame to be not less 2.72 Kg. (Square mouth traps 100 x 100 mm size)

SHIV KANT PRASHAR

Gopal Mahajan