A/R and M/O SP Residence in LIG Colony Dhalpur Kullu.

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m (One point five metre) in width or 10 sqm (Ten square metre) on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m (One point five metre), including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m (Fifty metre). All kinds of soil. with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level with in all leads and lift of materials and as per direction of Engineer-in-charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth Cement mortar 1:6 (1 cement : 6 coarse sand) with in all leads and lift of materials and as per direction of Engineer-in-charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) with in all leads and lift of materials and as per direction of Engineer-in-charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing 18 mm (Eighteen metre) thick gang saw cut, mirror polished, mouded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm (Twenty metre) thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, uring, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade.Area of slab over 0.50 sqm (Zero point fifty metre) with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).Kiln seasoned and hemically treated hollock wood with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc. Kiln seasoned and chemically treated hollock wood with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-incharge. (Note:- Butt hinges and necessary screws shall be paid separately) 35 mm (Thirty five metre) thick shutters with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm (Twenty five millimetre) to 40 mm (Forty millimetre) thick. (a) Kiln seasoned and chemically treated hollock wood with in all leads and lift of materials and as per direction of Engineer-in-charge.

(b) Float glass panes 4 mm (Four millimeter) thick (weight not less than 10 kg per sqm (Ten kilogram per square metre) with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm (One point four millimetre) in both directions with wire of dia 0.63 mm (Zero point sixty three millimetre), for doors, windows and clerestory windows with hinges and necessary screws. Kiln seasoned and chemically treated hollock wood with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete. Kiln seasoned and chemically treated hollock wood 50x12 mm (Fifty x Twelve millietre) with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete. 75x47x1.70 mm (Seventy five x Forty seven x One point seventy millimeter) with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete. 250x16 mm (Two hundred fifty x Sixteen millimetre) with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing aluminium tower bolts, ISI marked, anodised anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete. 200x10 mm (Two hundred x Ten millimetre) with in all leads and lift of materials and as per direction of Engineer-in-charge.

(b) 100x10 mm (One hundred x Ten millimetre)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete. 125mm (One hundred twenty five millimetre) with in all leads and lift of materials and as per direction of Engineer-in-charge.

(b) 75mm (Seventy five millimetre)

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in- charge (Frame work shall be paid for separately). 12mm (Twelve millimetre) thick commercial ply conforming to IS: 1328 BWR type with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing 19mm (Nineteen millimeter) thick water proof commercial board in shelves/box for cup board with butt joints & fixing with nails & screws etc complete with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing 19mm (Nineteen millimeter) thick Commercial Board water proof shutters for up boards i/c fixing with nickel plated piano hinges with screws etc complete with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm (One point five millimetre) thick with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing P.V.C edge bending tape 2.00mm (Two point zero millimetre) thick of approved brand . Wherever required edge to be sealed with approved adhesive etc. complete with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing stainless steel soft close auto hinges. (dadoo hinges ) with necessary screw fittings etc. complete with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and Fixing S.S. steel handle approved design make and size with necessary screw etc. complete with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg (Thirty five kilogram) and door width upto 700 mm (Seven hundred millimetre)), with necessary accessories and screws etc. complete with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing 40x5 mm (Forty x Five millimetre) flat iron hold fast 40 cm (Forty centimetre) long including fixing to frame with 10 mm (Ten millimetre) diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm (Thirty x Ten x Fifteen centimetre) 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm (Twenty millimetre) nominal size) with in all leads and lift of materials and as per direction of Engineer-in-charge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete with in all leads and lift of materials and as per direction of Engineer-in-charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm (Twelve millimetre) thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm (Three point three kilogram per square metre), including pointing in white cement mixed with pigment of matching shade complete with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved make, in all colours and shades, laid on 20mm (Twenty millimetre) thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (Three point three kilogram per square metre) including grouting the joints with white cement and matching pigments etc., complete . (a) Size of Tile 500x500 mm (Five hundred x Five hundred millimetre) with in all leads and lift of materials and as per direction of Engineer-in-charge.

(b) Size of Tile 600x600 mm (Six hundred x Six hundred millimetre)

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm (Eight millimetre) diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm (Zero point sixty three millimetre) thick with zinc coating not less than 275 gm/m² (Two hundred seventy five gram/metre square). with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing of 40 cm (Forty centimetre) overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts, G.l. limpet and bitumen washer complete, bent to shape and fixed in wall with cement mortar 1:3 (1 cement : 3 coarse sand).1.00 mm (One point zero millimetre) thick with zinc coating not less than 275 gm/m² (Two hundred seventy five gram/metre square). with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing 15 cm (Fifteen centimetre) wide, 45 cm (Forty five centimetre) overall semicircular plain G.S. sheet gutter with iron brackets 40x3mm (Forty x Three millimetre) size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete.0.63 mm (Zero point sixty three millimetre) thick with zinc coating not less than 275 gm/m² (Two hundred seventy five gram/metre square). with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten millimetre) gap for thermal expansion, (i) Single socketed pipes. (a) 75 mm (Seventy five millimetre) diameter with in all leads and lift of materials and as per direction of Engineer-in-charge.

(b) 110mm (One hundred ten millimetre) diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimetre) gap for thermal expansion. (a) Coupler 75 mm (Seventy five millimetre) dia. with in all leads and lift of materials and as per direction of Engineer-in-charge.

(b) Single tee with door 110x110x110 mm (One hundred ten x One hundred ten x One hundred ten millimetre)

(c) Single tee without door 110x110x110 mm (One hundred ten x One hundred ten x One hundred ten millimetre)

(d) Bend 87.5° (1) 75 mm (Seventy five millimetre) bend

(2) 110 mm (One hundred ten millimetre) bend

(e) Shoe (Plain) (1) 75mm (Seventy five millimetre) dia .

(2) 110 mm (One hundred ten millimetre) dia.

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm (Eight millimetre) dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2mm (Two millimetre) thick flat with in all leads and lift of materials and as per direction of Engineer-in-charge.

20 mm (Twenty millimetre) cement plaster on rough side of single or half brick wall of mix: 1:4 (1 Cement : 4 Course sand) with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and laying WIPRAQUET ( leminate HDF Flooring of approved brand and manufectur over C.C. base with polythene and foam sheet cusion below as per specification complete with approved. colour and design with in all leads and left complete with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing Australian pine wood panelling for manufectured tongued and grooved joint in plain lining panelling fixed on wood work complete with in all leads and lift of materials and as per direction of Engineer-in-charge.

Finishing walls with Acrylic Smooth exterior paint of required shade. New work (Two or more coat applied @ 1.67 ltr/10 sqm (One point sixty seven litre/ Ten square metre) over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm (Two point twenty kilogram/ Ten square metre)) with in all leads and lift of materials and as per direction of Engineer-in-charge.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm (Zero point ninety litre/ Ten square metre) over an under coat of primer applied @ 0.80 ltr/ 10 (Zero point eighty litre/ Ten square metre) sqm of approved brand and manufacture with in all leads and lift of materials and as per direction of Engineer-in-charge.

French spirit polishing (Two or more coats) on new works including a coat of wood filler. with in all leads and lift of materials and as per direction of Engineer-in-charge.

Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade. Old work (one or more coats) with in all leads and lift of materials and as per direction of Engineer-in-charge.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work with in all leads and lift of materials and as per direction of Engineer-in-charge.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade. One or more coats on old work with in all leads and lift of materials and as per direction of Engineer-in-charge.

French spirit polishing One or more coats on old work with in all leads and lift of materials and as per direction of Engineer-in-charge.

Finishing walls with Acrylic Smooth exterior paint of required shade. Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm (One point sixty seven litre/ Ten square metre)) on existing cement paint surface with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing polycarbonatd tranparent sheet 1.20mm (One npopint twenty millimetre) thick in roofing with galvanised J or L hooks bolts and nuts with G.I. Limpet and bitumen rubber washer complete with in all leads and lift of materials and as per direction of Engineer-in-charge.

Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm (Fifteen x Ten x Ten centimetre) with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm (Twenty millimetre) nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete .Door chowkhats with in all leads and lift of materials and as per direction of Engineer-in-charge.

Renewing glass panes, with wooden fillets wherever necessary: Float glass panes of nominal thickness 4 mm (Four millimetre) (weight not less than 10kg/sqm(Ten kilogram/ square metre)) with in all leads and lift of materials and as per direction of Engineer-in-charge.

Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres (Fifty metres) lead. In lime mortar with in all leads and lift of materials and as per direction of Engineer-in-charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres (Fifty metres) lead: Of area 3 sq. metres (Three square metre) and below with in all leads and lift of materials and as per direction of Engineer-in-charge.

Dry stone pitching 22.5 cm (Twenty two point five centimetre) thick including supply of stones and preparing surface complete with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing wash basin with C.I. brackets, 15 mm (Fifteen millimtre) dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- White Vitreous China Wash basin size 550x400 mm (Five hundred fifty x Four hundred millimetre) with a 15 mm (Fifteen millimtre) CP Brass single hole basin mixer with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipe with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete : 10 litre (Ten litre) capacity - White with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete: Flexible pipe 32 mm dia (Thirty two millimetre) with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing vanity top wash basin with single hole including fittings C.P. etc. complete with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing 15mm (Fifteen millimetre) C.P. single hole lever opeated wash basin. Mizor with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing 600x450 mm (Six hundred x Four hundred fifty millimetre) beveled edge mirror of superior glass (of approved quality) complete with 6 mm (Six millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing: (a) Rectangular shape 453x357 mm (Four hundred fifty three x Three hundred fifty seven millimetre) with in all leads and lift of materials and as per direction of Engineer-in-charge.

(b) Rectangular shape 1500x450mm (One thousand five hundred x Four hundred fifty millimetre)

Providing and fixing toilet paper holder: C.P. brass with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providng and fixing Tumbler holder with necessary fittings etc. complete with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing C.P. towel rail 600mmX20mm (Six hundred x Twenty millimetre) with brackets fitting wooden cleats raw pleg necessary screw etc. complete with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing white viterous china extended wall mounting water closet of size 780x370x690 mm (Seven hundred eighty x Three hundred seventy x Six hundred ninety millimetre) of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (Three litre/ Six litre) (adjustable to 4 litre/ 8 litres (Four litre/ Eight litre)), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m (One point zero millimetre) spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge.Concealed work,including cutting chases and making good the wall etc .PN - 16 Pipe, 25mm (Twenty five milimetre) OD (SDR-7.4) with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801 UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer-in-Charge.External work: PN - 16 Pipe, 20mm (Twenty millimetre) OD (SDR-7.4) with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 Cm (Forty five centimetre) length 15 mm (Fifteen millimetre) nominal bore with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing C.P. brass shower rose with 15 or 20 mm (Fifteen or Twenty millimetre) inlet : 100 mm (One hundred millimetre) diameter with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms (Eight hundred ten grams). 15 mm (Fifteen milimetre) nominal bore with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 : 15mm (Fifteen millimetre) nominal bore with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing C.D. Brass conceled body single lever high flow direction with button assembly with exposed part as C.D. lever all accerance complete with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing 150mm (One hundred fifty millimetre) dia chromium plated grating of superior quality for flour gully and nahani trap with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing Botanical wall papr for wall living room approved Textured self adhesive Decal Texture approved by Engineer -in-charge fixing proper finished at corner no any air grip between walls and wallpaper. complete. in all respect lead and left with in all leads and lift of materials and as per direction of Engineer-in-charge.

Providing and fixing stainless steel racks for untensile with Telscopic drawing slides with necessary screw etc. complete. (a) for full plate 300mm (Three hundred millimetre) Rack with in all leads and lift of materials and as per direction of Engineer-in-charge.

(b) for half plack 200mm (Two hundred millimetre) Rack

Ajeet Sharma