PROVN OF SECURITY WALL, WATCH TOWER AND ROAD WORKS UNDER AGE(I) DHARAMSALA

Amount

Surface excavation not exceeding 30cm deep and averaging 15 cm deep and getting out in hard/dense soil complete all as specified and directed.

Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out in hard and dense soil, complete all as specified and directed.

All as per ser item No 2 above but depth exc 1.50 metre & n.exc 3.00metre.

Rough excavation not exceeding 1.5 m deep and getting out in hard/dense soil complete all as specified and directed.

Excavation over areas, n.exc 1.5 m deep and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25Cm, complete all as specified and directed.

Removing excavated materials/ soils, not exceeding 50mtrs and depositing where directed at a level not exceeding 1.50mtrs, complete all as specified and directed.

Removing excavated materials/ soils, exceeding 50mtrs but not exceeding 250mtrs and depositing where directed at a level not exceeding 1.50mtrs, complete all as specified and directed.

Earth filling under floors or pavings laid in layers not.exceeding 25cm thick, spread, leveled and rammed including watering complete all as specified and directed

Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed

Hard core of broken stone or boulders of gauge not exc 63 mm deposited ,spread and leveled in layer not exc 15 cm thick complete all as specified and directed.

Hand packing of broken stone or boulders (anythickness) at back of walls over arches etc. and raising (or lowering) to the required level complete all as specified and directed.

PVC (SWR) pipe, 110mm dia of pressure rating 4kg/sqcm, as in weep hole (retaining wall) complete all as specified & directed.

PCC 1:5:10 (nominal mix) type E-2 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete complete all as specified and directed.

PCC 1:4:8 (nominal mix) type D-2 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete complete all as specified and directed.

PCC 1:3:6 (nominal mix) type C-2 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete complete all as specified and directed.

PCC 1:3:6 (nominal mix) type C-2 (using 40mm graded crushed stone aggregates) as in surface channel and drains complete all as specified and directed.

Plain cement concrete 1:2:4 ( nominal mix ) type B-1 (using 20 mm graded crushed stone aggregates) as in in lintels upto 1.5m clear span, cills, steps; seismic and other similar ands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary formwork where required complete all as specified and directed.

RCC M-25 (Design mix) type A-1 (using 20 mm graded crushed stone aggregates ) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete and like complete all as specified and directed.

RCC M-25 (Design mix) type A-1 (using 20 mm graded crushed stone aggregates ) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

RCC M-25 (Design mix) type A-1 (using 20 mm graded crushed stone aggregates ) as in Columns, pillars, piers, posts and struts and like complete all as specified and directed.

RCC M-25 (Design mix) type A-1 (using 20 mm graded crushed stone aggregates) as in beams, cantilevers and like complete all as specified and directed.

3mm thick fiber glass sheet complete all as specified and directed.

Concrete bed to drain pipe of 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) complete all as specified and directed. Note :- Thickness of bed and width of bed shall be provided all as per preamble a (i) & a (ii) on Srl page no 356 of SSR Part-II Rates (2010).

Salt glazed stoneware drain pipe 150 mm dia grade'A' laid in trenches and jointed with cement joints complete all as specified and directed

Precast cement concrete as in landing, cover slabs (for manhole etc) and similar articles with precast cement concrete Type B-1, 1:2:4 (20mm graded crushed stone aggregate) and setting in cement mortar 1:4 complete all as directed.

Form work to sides of concrete foundation, footing, base of columns, and similar works for rough finished surface complete all as specified and directed.

Use & waste of form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces of concrete, complete all as specified & directed.

Use & waste of form work to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc alo splays between floors and beamsfor rough finished surfaces of concrete, complete all as specified & directed.

Form work to edges of concrete floor & roof slab not exceeding 20cm wide for fair finished surface of concrete complete all as specified and directed.

Brick work with old size fly ash bricks, class 7.5, straight or curved on plan exc. 6 metre mean radius built in cement mortar 1:6 (01 cement : 06 coarse sand) all as specified & directed.

Walling of random rubble stone masonry brought upto course well bonded bedded and soilidly hearted built in CM 1:6, complete all as specified and directed.

PCC 1:2:4 (nominal mix), type B-1 using 20mm graded crushed stone aggregate as in precast bond stones, set in cement mortar 1:6, complete all as specified & directed.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain coloured PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 160 of MES SSR 2010 Part-II

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5 mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1) specified and directed.

Factory made solid panel PVC ventilator shutter (fully glazed) 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails.M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Pane of 4 mm thick sheet glass to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1) specified and directed.

Aluminium handles cast type anodized of size 150 mm complete all as specified and directed.

Aluminium anodized barrel tower bolt of extruded section of size 100 mm and fixed complete all as specified and directed.

Mild steel butt hinges of size 100 mm medium weight cold rolled complete all as specified and directed.

3 mm thick, figured glass pin head type and glazing with oil putty in squares n.exc 0.5 sqm each pane complete all as specified and directed.

4 mm thick non asbestos fibre cement building boards as in ceiling fixed or laid/ inserted to timber/ GI/ aluminium frame work fixed with nails, all as specified.

2nd class hard wood ,40mm thick as in boarding, planed both sides with butt joints, fixed with nail in any situation, complete all as specified & directed.

Prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

Prepainted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge, hips, valley/ eaves/ rain water gutters, drip and straight flashing (length and girth as fixed), fixed with self tapping screws all as specified

Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete drilled for fixing of steel sheeting or other covering, doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe 410-0 or Fe 310-0, complete all as specified.

2mm thick mild steel plain black sheet in wall cladding ,steel gates and similar works ,cut to size ,holes punched, including round headed screws, clout nails or rivets and fixed to steel framing with plain 40mm lap joints with riveted or welded seams including bending or turning up, mitred angles etc as required all as specified and directed.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe 410 -W (Gde-E- 250) quality-A, complete all as specified and as directed.

Mild steel work as in hold fast, wind ties for roof including securing bolts including all necessary drilling ,bolting or reverting etc and all similar work conforming to Fe-290 (Gde E-165) complete all as specified and directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n.exc 5 cm long, dia of shank 11mm to 15 mm all as specified.

Mild steel bolts purpose made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut exc 30cm long and diameter of neck exc 25mm all as specified.

Framed work such as grills, gratings etc with ends of bars shouldered and/or riveted or forged into spikes framed guard bars including cutting, drilling, welding etc confirming to Fe-290 Gde E-165 all as specified and directed.

Mild steel framed works as in brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc., n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Rolled mild steel work as in stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc. complete, and similar work conforming to Fe-410W Gde E-250) Quality A complete all as specified and directed.

Rolled mild steel work as in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment, and similar work conforming to Fe-410W Gde E-250) Quality A complete all as specified and directed.

Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails, straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins, etc., complete all as specified. (each line wire to be measured) complete all as specified and directed.

Punched tape concertina wire, made to shape as dia exc. 450mm but not exceeding 600mm, put on the wall in between 'Y' shape angle iron post and secured with necessary binding wire all as directed. Note:- Weight per RM as laid shall be assessed by the AGE(I).

Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

100mm thick PCC 1:5:10 type E-2 (using 40 mm graded crushed stone aggregates) as in sub base complete all as specified and directed. .

75mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregates) as in sub base complete all as specified and directed. .

75 mm thick PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates) as in floor finish, surface finished even and smooth without using extra cement complete all as specified and directed.

40 mm thick PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates) as in floor finish, surface finished even and smooth without using extra cement complete all as specified and directed.

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

Mat finish, premium quality, joint free (edge cut), coloured/ printed ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed.

Glazed ceramic coloured tiles of size 300mm x 200 mm x 7 mm thick as in vertical surfaces , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick cement screed in cement mortar 1:3 complete all as specified and directed. Size/Shade/Colour of tile shall be approved by the GE.

Rendering cement plaster 20mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (15mm thick first layer and 5mm thick second layer) on other than fair faces of brick wall or on stone masonry surfaces, mixed with water proofing admixture as per manufacturer's instructions, trowelled to even and smooth finish without using extra cement complete all as specified. (Note:- WPC will be measured and paid separately)

Rendering cement plaster 15mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on stone masonry or surface other than fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Broken glass (broken glass bottle or thick glass) coping on top of wall @ 10 Kg/ Sqm firmly embedded over 25mm layer of cement mortar 1:3 including weathering, slightly rounded or chamfered angles and throating including necessary formwork where required complete all as specified.

Supply only liquid water proofing admixture.

Extra over stone walling of granite, trap or basalt stone for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses with maximum depression on face from straight edge held against the dressed surface n exc 40mm, complete all as specified & directed.

Raised pointing to random or polygonal rubble, uncoursed or brought upto courses in cement mortar 1:4, complete all as specified.

Preparation of steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of wooden surfaces of any description and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer over and including 2mm thick wall care putty (applied in two layers), finished smooth with sand paper complete all as specified and directed.

Three coats of white wash on newly plastered or un plastered, previously undecorated walls surfaces including preparation of surfaces complete, all as specified.

Three coats of white wash on newly plastered or un plastered, previously undecorated ceiling surfaces including preparation of surfaces complete, all as specified.

Preparation of newly plastered or un plastered, previously undecorated wall surfaces and applying two coats of acrylic emulsion anti fungal (exterior) weather proof paint over and including a coat of primer complete all as specified and directed.Make:- Berger (weather all coat guard)/ Asain (apex ultima/ Nerolac (excel).

Preparation of new plastered surfaces or un plastered, previously undecorated wall surfaces and applying two coats of cement base paint, complete all as specified and directed.

G I tubing medium grade of 15 mm bore with all fittings and fixtures fixed to wall and ceiling or laid in floor/trenches complete all as specified and directed.

GI tubing medium grade of 20 mm bore with all fittings and fixtures fixed to wall and ceiling or laid in floor /trenches complete all as specified and directed.

Supply Only GI tubing medium grade of 20 mm bore complete all as specified and directed.

Cutting chases, pinning in. making good to facings here required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good complete all as specified.

Brass chromium plated tubular towel rail 20 mm dia, "D" type, 60 cms long between flanges with and including chromium plated brass brackets, brass screws complete all as specified

Chromium plated soap dish, fixed in repair complete all as specified.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

Wash basins, Vitreous China (Flat white type) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, waste pipe of polythylene of low or high density or PVC of 32mm dia including Pillar taps, 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed, complete all as specified. Make: Cat Part No. 1008 of Cera or equivalent in makes mentioned in Appx

Stop valves/ angle valve/ concealed valve, cast copper alloy, chromium plated, fancy type, screwed down, high pressure , screwed both ends for 15mm bore iron pipe or for unions and complete, all as specified. Type of valve approved by the GE.

Stop valves cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 20mm bore iron pipe or for unions and fixed in repairs complete, all as specified.

Bib tap, cast copper alloy ,chromium plated, fancy type , screwed for iron pipe or for brass ferrule of 15 mm bore complete all as specified and directed.

PVC connections 15 mm size with PTMT nuts of length 600mm fixed in repair complete all as specified and directed.

PVC valve less, crystal white, syphonic action type flushing cistern 10 litre capacity, superior quality, plunger type, low level, with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long and 15 mm dia 600 mm long PVC connection with CP brass coupling nuts and PVC washers at both ends fixed, all as specified. Make: Cat Part No. 2602 of Cera or equivalent in makes mentioned in Appx .

600x450 mm bevelled edge mirror of slected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plug with chromium plated brass screwed and cup washers.

Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-I using 20 mm graded crushed stone aggregate complete all as specified, incl making connections to trap and to flush pipe, etc all as specified. Make: Cat Part No. 2071 of 'Cera' or equivalent makes mentioned in Appx.

110mm dia PVC(SWR) pipe single socketed with rubber ring joints, laid/fixed to tranches or in floor or walls complete all as specified and directed.

75mm dia PVC(SWR) pipe single socketed with rubber ring joints, laid/fixed to tranches or in floor or walls complete all as specified and directed.

110 mm dia PVC(SWR) bend, any radius complete all as specified and directed.

110 mm dia PVC (SWR) reducers complete all as specified and directed.

125/110mm dia PVC (SWR) 'S' trap complete all as specified and directed.

75 mm dia PVC(SWR) vent cowl complete all as specified and directed.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

75mm dia PVC (SWR) junction single, (single T) equal or unequal provided with oval access door complete all as specified and directed.

Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete all as specified and directed.

75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity four layered (ISI Marked) cylinderical vertical with closed top, hoisted and fixed in position with ball brass valve, high pressure with PVC float valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line complete all as specified.

LLDPE septic tank designed to carry sewage and sludge water, Comprising earth work, excavation in hard rock, returning filling, disposal of surplus spoils to a distance not exc 50 meter from starting points, PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) in foundation, 200mm thick, Vent shaft, connections etc. for 10 users (1600 litre capacity) including all fittings, fixtures, testing on completion Approximate Dimensions. Dia 1440 mm, height 1550 mm and total HRT 48 hr complete all as specified and directed. MAKE:- Sintex or equivalent make as approved.

Construction of soakage well 1.20 meter internal dia x 3.00 meter effective depth including earth work in hard rock cum hard soil, foundation in PCC 1:3:6, fly ash brick wall walls of honey combed with top ring of M-25 (Design Mix) using 20mm graded crushed stone aggregate concrete, form work, reinforcement including intercepting chamber and screen chamber made of brick masonary in CM (1:4) , RCC cover slab in M25/SFRC cover, interconnecting pipes of RCC/DWC/cast iron pipes, bends and fittings. Complete, filled with brick bats complete all as shown on drgs,specified and directed .

Rolling and consolidating formation surfaces in cutting with 8 to 12 tonne power roller, including filling in soft spots, depressions, etc. which occur during rolling (for portion coming in cutting/original ground only) to required camber and gradient, etc. including watering before or during rolling, all complete all as specified and as directed .

150 mm thick (spread thickness) soling (or sub base) with broken boulders or quarried stones of size range 100 to 50mm, deposited, spread, leveled in one layer, interstices filled, surface formed and rolled and consolidated to required gradient and camber with 8 to 12 tonne power roller, complete all as specified and as directed.

150mm thick (in two layers each 75mm thick)(compacted thickness) WBM with coarse aggregate of granite, trap or basalt stone of grading 2 (63 to 40mm size), spread, rolled and consolidated with power roller of 8 to 12 tonne to required gradient and camber, complete all as specified.

Preparing unsurfaced water bound macadam surfaces by brushing with wire brushes for removing caked mud etc sweeping with brooms and finally the cleaned surfaces with power sweeper or compressor to remove all loose dirt etc, applying evenly a priming/ tack coat with bituminous primer using paving bitumen (VG-10) at 10 kg per 10 sq metre of road surface, laying bituminous premix semi dense asphaltic concrete 40mm consolidated thickness with 5.5% binder content by weight of total mix using 20mm crushed stone aggregate rolled and compacted to required camber and gradient with 8 to 10 tonne power roller, complete all as specified and directed. Note:- Bituminous premix semi dense asphaltic concrete shall be mixed in hot mix plant, transported and premix carpet shall be laid in single layer with self propelled mechanical paver, rolled with vibrator roller.

Providing premix bituminous, macadam (consolidated thickness 75mm or less) with 4% binder content of paving bitumen (Grade VG-10) by weight of total mix, 20mm crushed stone aggregate, laid, rolled and compacted to required camber and gradient with 8 to 10 tonne power roller, complete all as specified and directed. Note:- Bituminous premix semi dense asphaltic concrete shall be mixed in hot mix plant, transported and premix carpet shall be laid in single layer with self propelled mechanical paver, rolled with vibrator roller.

Continuous brick edging; with width equal to the width of the brick; laid dry on end vertically with old size fly ash bricks, class 7.5 including necessary earthwork complete all as directed.

Point wiring with 1.5 Sqmm copper conductor FRLS (Multistrand) PVC insulated ISI Marked unsheathed cable in and including PVC conduit not less than 20mm dia, medium grade with IS 9537 (Part-III) 1983 marking with all fittings/ accessories as specified in preamble 1 (a) to (q) of Section 19 of SSR Part-II, under heading point wiring and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FLRS as earth wire (green colour) connected to common earth dolly and including pressed steel terminal boxes made out of 1.20 mm thick mild steel sheet duly painted with one coat of red oxide primer for mounting of switches, sockets, fan regulators, light fittings etc. covered with 3mm thick plastic laminated sheet (Make Hylum or equivalent ISI marked) for one light point or one fan point or one fan point through regulator or one bell point, controlled by one way switch/ push button complete including making good disturbed surfaces to match with existing all as specified and directed.

All as per serial item No '114' above, but for one 3 pin 5 Amps socket outlet, independent all as specified and directed.

All as per serial item No. '114' above but for 3 pin 15 Amps socket out let independent with 2.5 Sqmm PVC copper conductor cable and and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified.

Switch piano flush type, single pole, one way, 5 Amps, all as specified.

Switch piano flush type, single pole, one way, 15 Amps, all as specified.

Switch socket combination two in one, 5 amps flush type, all as specified.

Switch socket combination two in one, 3 Pin 5 amps and 15 amps, flush type, all as specified.

Ceiling rose, 65 mm to 50 mm, two to three terminals, PVC/ Polycarbonate, insulated body fixed on PVC block, all as specified.

Exhaust fan, 200 mm sweep, 1400 RPM, 230 Volts, AC, 50 Hz, single phase, non metallic type complete with louvers , fixing arrangement in any condition and making connections with suitable capacity copper twin core conductor and ceiling rose, complete all as specified and directed.

Electric geyser (Water storage heater), 25 Ltrs, 5 star rated, including two nos of 400mm long hot and cold PVC connection including grouting of nuts, bolts & washer on wall and making good the disturbed surface including plaster work complete all as directed. Make: Havells Cat Part No GHWAMGSIB025 or equivalent in BAJAJ/CROMPTON GREAVES/ JAGUAR/USHA LEXUS/MORPHY RICHARDS

Wall mounted LED integrating batten fitting T5, 20 Watt LED, 4 feet, PVC extruded with 20 watt LED tube rod with all acessoreis prewired and making connection with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete. Havell's Cat Part No. LHEBTP7UN1W018/ C&S cat PART No LTTB4F20WLEDP/W/ Philips CAT Part No BN021LED20S-6500 NW PSU GR or equivalent in makes mentioned in Appx.

MCB SPN 6 to 32 Amp, 240 Volts, 10 KA all as specified.

MCB SP 6 to 32 Amp, 240 Volts, 10 KA all as specified.

Sheet metal enclosures for DBs when MCBs to be used, single pole and neutral, 4 way, double door, 240 volts with 200 Amp rated bus bar completed all as specified. Make : Havells Cat Part No. DHDPSHODPW04/ C&S Cat Part No CSDBSPNSD04 or equivalent in makes mentioned in Appx.

LED 60 W, street light fitting, energy saving and environmental friendly , made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having top opening, seperate driver compartment with IP66 protection and impact resistance of IK07 with 10KV Built-in SPD complete fixed on pole/ wall with and including bracket made out of galvanised iron pipe 40mm dia, medium grade of length 1.50 metres with two clamps made out of mild steel flat 25x4 mm with nuts, bolts and washers complete accesseries including two coats of aluminium paint after preparation of surfaces including making connection with aluminium PVC insulated copper wire 2.5 sqmm as required at site and connecting the same to the cable with the help of the connector all as specfied and directed . Make:- Havells Cat Part No LHETBXU7PA7B060 or equivalent in makes mentioned in PS.

LED 25W, 5700K, new generation, post-top, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs complete fixed on pole with and including bracket made out of galvanised iron pipe 40mm dia, medium grade of suitable length fixed in PCC complete including two coats of aluminium paint after preparation of surfaces including making connection with aluminium PVC insulated copper wire 2.5 sqmm as required at site and connecting the same to the cable with the help of the connector all as specfied and directed . Make:- Havells Cat Part No LHEVBHP7PN6K025 or equivalent in makes mentioned in PS.

Street light terminal boxes made out with SMC material, shock & dust proof of size 250mm x 200mm x 100 mm as per IS and including 100A TPN busbar fixed on insulators, 01 No 6A SP MCB, earth terminal with nuts and washers including 02 coats o aluminum paint over a coat of primer complete all as specified and as directed.

Gate light cover, made out of 25mm x 25mm x 3mm angle iron frame and 4mm dia GI wire mesh of size 700mm X 600mm X 600mm at an interval of 25mm c/c and 4 Nos 100mm long anchor nuts and bolts, grouted on top of gate wall with openning arrangement for maintenance/ repair work, complete as directed.

Sand cushioning to under ground cables provided with a layer of sand 8 cms thick before laying the cable and 15 cms thick after laying the cable complete all as specified and directed.

Sub class "B" bricks for covering to cable laid dry flat, with width equal to length of bricks all as specified and directed.

1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular stranded conductor size of 10 sqmm, 2 core and taking down, complete all as specified.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with multi-standard aluminium conductor, 1100 volts grade, cross sectional area 25 Sqmm, 2 core, laid in trenches or passing through pipes, including making necessary connections at both ends, complete all as specified and directed.

Steel tubular swaged poles complete with base plate 8mm thick welded with pole, finial taper plug, bolt, nut and screws as specified type 410 SP-31 (9m long) including one coat of red-oxide zinc chrome primer and two coats of aluminium paint on surfaces exposed to view and making 30cm wide strips (total 5 Nos) with yellow and black paint alternately on external surface above PCC benching and numbering with black paint and painting with bituminous paint internally complete and externally for portion embedded in PCC, complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in PCC M-15, type B-I using 20mm graded crushed stone aggregates with 40mm thick precast cover of size 550 mm X 550 mm X 75 mm of RCC (1:2:4), type B-I, reinforced with XPM (weight not less than 4 kg/ Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion.