Construction of (250 x 30 Sqm) of Shed with EOT crane (25 Tons) facility in General Stores Area of MM-stores Department (SHED 1) at Bokaro Steel Plant, Bokaro Steel City, Jharkhand

ABSTRACT OF COST

Name of the work : Construction of 250mx30m of shed with 25 Tons (Revised) EOT

Crane facility in General Store Area of MM- Stores Department (SHED-1)

S.H. No. Description of Sub-Head Amount Amount

(DSR items) (Non-DSR items)

02. Concrete Work : ₹ 95,35,090.00 -

03. Reinforced Cement Concrete : ₹ 4,97,27,093.00 -

05. Cladding Work : ₹ 11,06,835.00 -

06. Wood and P.V.C. Work : ₹ 1,79,118.00 -

11. Aluminium Work : ₹ 8,31,116.00 -

12 Fire Fighting (Fire Hydrant System) : ₹ 4,78,445.51 ₹ 3,05,010.00

13 Sanitary Fixtures & CP Brass Fittings : ₹ 78,340.90 ₹ 22,706.00

14 Soil, Waste, Vent & Rain Water Pipes : - ₹ 17,27,374.28

15 Water Supply System (Internal) : ₹ 65,957.93 -

16 External Sewerage & Storm Water Drainage : ₹ 1,72,800.58 ₹ 4,95,000.00

17 External Water Supply : ₹ 56,434.46 -

21 Administrative Block : ₹ 1,36,34,567.36 ₹ 37,45,829.91

22 Supply of Equipments - ₹ 12,60,000.00

Dismantlling of existing facilities, Relocation of

pipeline, cable (Lumsum Payble)

After adding cost index @ 10% as per CPWD

Included in rate

office memorandum 34(1)/cost index/

Modified Estimated Cost after using Correction

factor on DSR 2023 on account of Included in rate

Gross Total (W) ₹ 24,98,22,199.99

Digitally signed by PRIYA

(SCHEDULE OF QUANTITIES - Civil Works)

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General

Store Area of MM- Stores Department (SHED-1 )

Sl. No Description of Item Quantity Unit Rate (Rs) Amount(Rs)

Sub-Head : Earth Work

1 2.6 Earth work in excavation by mechanical means (Hydraulic

excavator) / manual means over areas (exceeding 30cm in

depth, 1.5m in width as well as 10 sqm on plan) including

getting out and disposal of excavated earth, lead up to

50m and lift up to 1.5m,as directed by Engineer-in-Charge.

3 2.7 Earth work in excavation by mechanical means (Hydraulic

excavator) / manual means over areas (exceeding 30 cm in

depth, 1.5m in width as well as 10 sqm on plan) including

getting out and disposal of excavated earth, lead up to 50

m and lift up to 1.5m, as directed by Engineer-in-Charge.

5 2.25 Filling available excavated earth (excluding rock) in

trenches, plinth, sides of foundations etc. in layers not

exceeding 20cm in depth, consolidating each deposited 2960.28 Cum 209.78 621004.00

layer by ramming and watering, lead up to 50 m and lift up

6 2.25A Excavating, supplying and filling of local earth (including

royalty) by mechanical transport up to a lead of 5 km, also

including ramming and watering of the earth in layers not 369.22 Cum 749.75 276818.00

exceeding 20 cm in trenches, plinth, sides of foundation

etc., complete.

4 2.26 Extra for every additional lift of 1.5 m or part thereof in

excavation /banking excavated or stacked materials.

5 2.26.1 All kinds of soil.

6 2.26.2 Ordinary or hard rock.

7 2.27 Supplying and filling in plinth with sand under floors,

including watering, ramming, consolidating and dressing 1125.00 Cum 2273.05 2557181.00

8 2.34 Supplying chemical emulsion in sealed containers including

delivery as specified.

9 2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% 4166.67 Ltr 251.25 1046887.00

10 2.35 Diluting and injecting chemical emulsion for PRE

CONSTRUCTIONAL anti- termite treatment (excluding the

cost of chemical emulsion) :

11 2.35.3 Treatment of soil under existing floors using chemical

emulsion @ one litre per hole, 300 mm apart including

drilling 12 mm diameter holes and plugging with cement

mortar 1 :2 (1 cement : 2 Coarse sand) to match the

existing floor :

12 2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1%

Total of the Sub-Head - Earth Work : 7995314.00

Sub-Head : Concrete Work

Digitally signed by PRIYA

Sl. No Description of Item Quantity Unit Rate (Rs) Amount(Rs)

13 4.1 Providing and laying in position cement concrete of

specified grade excluding the cost of centering and

shuttering - All work up to plinth level :

14 4.1.10 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from

natural sources : 10 graded stone aggregate 40 mm 131.64 Cum 6976.86 918429.00

nominal size derived from natural sources)

15 4.11 Providing and laying damp-proof course 50mm thick with

cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III)

derived from natural sources : 4 graded stone aggregate 117.00 Sqm 530.60 62080.00

20mm nominal size derived from natural sources).

16 4.12 Extra for providing and mixing water proofing material in

cement concrete work in doses by weight of cement as per 45.00 units 19.43 874.00

manufacturer’s specification.

17 4.13 Providing and applying a coat of residual petroleum

bitumen of grade of VG-10 of approved quality using 1.7 kg

per square metre on damp proof course after cleaning the 130.00 Sqm 156.42 20335.00

surface with brushes and finally with a piece of cloth lightly

soaked in kerosene oil.

18 4.17 Making plinth protection 50mm thick of cement concrete

1:3:6 (1 cement : 3 coarse sand (zone-III) derived from

natural sources : 6 graded stone aggregate 20 mm nominal

size derived from natural sources) over 75mm thick bed of

dry brick ballast 40 mm nominal size, well rammed and

consolidated and grouted with fine sand, including

necessary excavation leveling & dressing & finishing the

19 4.20 Providing and laying in position ready mixed or site

batched design mix cement concrete for plain cement

concrete work; using coarse aggregate and fine aggregate

derived from natural sources, Portland Pozzolana/Ordinary

Portland/Portland Slag cement, admixtures in

recommended proportions as per IS : 9103 to accelerate/

retard setting of concrete, to improve durability and

workability without impairing strength; including pumping

of concrete to site of laying, curing, carriage for all leads;

but excluding the cost of centering, shuttering and finishing

as per direction of the Engineer-in-charge; for the following

grades of concrete.

20 Note : Extra cement upto 10% of the minimum specified

cement content in design mix shall be payable separately.

In case the cement content in design mix is more than

110% of the minimum specified cement content, the

contractor shall have discretion to either re-design the mix

or bear the cost of extra cement.

21 4.20.1 All works up to plinth level:

22 4.20.1.1 Concrete of M-10 grade with minimum cement content of

Total of the Sub-Head - Concrete Work : 9535090.00

Sub-Head : Reinforced Cement Concrete

Digitally signed by PRIYA

Sl. No Description of Item Quantity Unit Rate (Rs) Amount(Rs)

23 5.3 Reinforced cement concrete work in beams, suspended

floors, roofs having slope up to 15° landings, balconies,

shelves, chajjas, lintels, bands, plain window sills,

staircases and spiral stair cases above plinth level up to

floor five level, excluding the cost of centering, shuttering, 1.00 Cum 12314.34 12314.00

finishing and reinforcement with 1:1.5:3 (1 cement : 1.5

coarse sand(zone-III)derived from natural sources : 3

graded stone aggregate 20 mm nominal size derived from

natural sources).

24 5.9 Centering and shuttering including strutting, propping etc.

and removal of form for :

25 5.9.1 Foundations, footings, bases of columns, etc. for mass

26 5.9.4 Shelves (Cast in situ)

27 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts

28 5.9.20 Suspended floors, roofs, landings, balconies and access

platform with water proof ply 12 mm thick

29 5.9.21 Lintels, beams, plinth beams, girders, bressumers and

cantilevers with water proof ply 12 mm thick

30 5.22 Steel reinforcement for R.C.C. work including straightening,

cutting, bending, placing in position and binding all

complete upto plinth level.

31 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or

32 5.22A Steel reinforcement for R.C.C. work including straightening,

cutting, bending, placing in position and binding all

complete above plinth level.

33 5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or

34 5.30 Add for plaster drip course/ groove in plastered surface or

moulding to R.C.C. projections

35 5.33 Providing and laying in position ready mixed or site

batched design mix cement concrete for reinforced cement

concrete work; using coarse aggregate and fine aggregate

derived from natural sources, Portland Pozzolana/

Ordinary Portland/ Portland Slag cement, admixtures in

recommended proportions as per IS: 9103 to accelerate/

retard setting of concrete, to improve durability and

workability without impairing strength; including pumping

of concrete to site of laying, curing, carriage for all leads;

but excluding the cost of centering, shuttering, finishing

and reinforcement as per direction of the engineer-in-

charge; for the following grades of concrete.

36 Note: Extra cement up to 10% of the minimum specified

cement content in design mix shall be payable separately.

In case the cement content in design mix is more than

110% of the specified minimum cement content, the

contractor shall have discretion to either re-design the mix

or bear the cost of extra cement

37 5.33.1 All works upto plinth level

38 5.33.1.1 Concrete of M25 grade with minimum cement content of

Digitally signed by PRIYA

Sl. No Description of Item Quantity Unit Rate (Rs) Amount(Rs)

39 5.33.1.2 Concrete of M30 grade with minimum cement content of

40 5.33.2 All works above plinth level upto floor V level

41 5.33.2.1 Concrete of M25 grade with minimum cement content of

42 5.33.2.2 Concrete of M30 grade with minimum cement content of

43 5.35 Add for using extra cement in the items of design mix over

and above the specified cement content therein.

Total of the Sub-Head - Reinforced Cement Concrete : 49727093.00

Sub-Head : Masonry Work

44 6.1 Brick work with common burnt clay F.P.S. (non modular)

bricks of class designation 7.5 in foundation and plinth in:

45 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 20.00 Cum 7633.65 152673.00

46 6.4 Brick work with common burnt clay F.P.S. (non modular)

bricks of class designation 7.5 in superstructure above

plinth level up to floor V level in all shapes and sizes in :

47 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 320.00 Cum 9746.10 3118751.00

48 6.13 Half brick masonry with common burnt clay F.P.S. (non

modular) bricks of class designation 7.5 in superstructure

above plinth level up to floor V level.

49 6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) 65.00 Sqm 1202.80 78182.00

50 6.15 Extra for providing and placing in position 2 Nos 6mm dia.

M.S. bars at every third course of half brick masonry.ird 65.00 Sqm 112.17 7291.00

course of half brick masonry.

Total of the Sub-Head - Masonry Work : 3356897.00

Sub-Head : Cladding Work

51 8.2 Providing and fixing 18 mm thick gang saw cut, mirror

polished, premoulded and prepolished, machine cut for

kitchen platforms, vanity counters, window sills, jambs,

facias and similar locations of required size, approved

shade, colour and texture laid over 20 mm thick base

cement mortar 1:4 (1 cement : 4 coarse sand), joints

treated with white cement, mixed with matching pigment,

epoxy touch ups, including rubbing, curing, moulding and

polishing to edges to give high gloss finish etc. complete at

52 8.2.2 Granite stone slab colour black, Cherry/Ruby red

53 8.2.2.1 Area of slab upto 0.50 sqm

54 8.2.2.2 Area of slab over 0.50 sqm

55 8.2.3 Granite stone slab all colour and texture except black,

Cherry/ Ruby red

56 8.2.3.1 Area of slab upto 0.50 sqm

57 8.2.3.2 Area of slab over 0.50 sqm

58 8.4 Extra for fixing marble /granite stone, over and above

corresponding basic item, in facia and drops of width upto

150 mm with epoxy resin based adhesive, including

cleaning etc. complete.

Digitally signed by PRIYA

Sl. No Description of Item Quantity Unit Rate (Rs) Amount(Rs)

59 8.5 Extra for providing opening of required size & shape for

wash basin/kitchen sink in kitchen platform, vanity counter

and similar location in marble/ Granite/ stone work,

including necessary holes for pillar taps etc. including

moulding, rubbing and polishing of cut edges etc. complete

60 8.31 Providing and fixing Ist quality ceramic glazed wall tiles

conforming to IS: 15622 (thickness to be specified by the

manufacturer), of approved make, in all colours, shades

except burgundy, bottle green, black of any size as

approved by Engineer-in-Charge, in skirting, risers of steps

and dados, over 12 mm thick bed of cement mortar 1:3 (1

cement : 3 coarse sand) and jointing with grey cement

slurry @ 3.3kg per sqm, including pointing in white cement

mixed with pigment of matching shade complete.

Total of the Sub-Head - Cladding Work : 1106835.00

Sub-Head : Wood and P.V.C. Work

61 9.1 Providing wood work in frames of doors, windows,

clerestory windows and other frames, wrought framed and

fixed in position with hold fast lugs or with dash fasteners

of required dia & length (hold fast lugs or dash fastener

shall be paid for separately).

62 9.1.2 Sal wood

63 9.7 Providing and fixing panelling or panelling and glazing in

panelled or panelled and glazed shutters for doors,

windows and clerestory windows (Area of opening for

panel inserts excluding portion inside grooves or rebates to

be measured). Panelling for panelled or panelled and

glazed shutters 25 mm to 40 mm thick :

64 9.7.7 Float glass panes

65 9.7.7.2 5.5 mm thick glass panes (weight not less than 12.50

66 9.21 Providing and fixing ISI marked flush door shutters

conforming to IS : 2202 (Part I) non-decorative type, core

of block board construction with frame of 1st class hard

wood and well matched commercial 3 ply veneering with

vertical grains or cross bands and face veneers on both

faces of shutters:

67 9.21.1 35 mm thick including ISI marked Stainless Steel butt

hinges with necessary screws

68 9.23 Extra for providing lipping with 2nd class teak wood

battens 25 mm minimum depth on all edges of flush door 15.00 Sqm 494.85 7423.00

shutters (over all area of door shutter to be measured).

69 9.24 Extra for providing vision panel not exceeding 0.1 sqm in

all type of flush doors (cost of glass excluded) (overall area

of door shutter to be measured) :

70 9.24.1 Rectangular or square. 15.00 Sqm 213.15 3197.00

71 9.40 Providing and fixing wooden moulded beading to door and

window frames with iron screws, plugs and priming coat

on unexposed surface etc. complete :

72 9.40.1 2nd class teak wood

Digitally signed by PRIYA

Sl. No Description of Item Quantity Unit Rate (Rs) Amount(Rs)

74 9.74 Providing and fixing bright finished brass tower bolts

(barrel type) with necessary screws etc. complete :

77 9.75 Providing and fixing bright finished brass door latch with

necessary screws etc. complete :

79 9.76 Providing and fixing bright finished brass 100 mm mortice

latch and lock with 6 levers and a pair of lever handles of 8.00 No. 914.73 7318.00

approved quality with necessary screws etc. complete.

80 9.82 Providing and fixing bright finished brass hanging type floor

door stopper with necessary screws, etc. complete.

81 9.127 Providing & Fixing decorative high pressure laminated

sheet of plain / wood grain in gloss / matt / suede finish

with high density protective surface layer and reverse side

of adhesive bonding quality conforming to IS : 2046 Type S,

including cost of adhesive of approved quality.

Total of the Sub-Head - Wood And P.V.C Work : 179118.00

Sub-Head : Steel Work

83 10.19 Providing and fixing mild steel round holding down bolts

with nuts and washer plates complete.

84 10.27 Providing and fixing carbon steel galvanised (minimum

coating 5 micron) dash fastener of 10 mm dia double

threaded 6.8 grade (yield strength 480 N/mm2), counter

sunk head, comprising of 10 mm dia polyamide PA 6 grade

sleeve, including drilling of hole in frame , concrete/

masonry, etc. as per direction of Engineer-in-charge.

Total of the Sub-Head - Steel Work : 1184501.00

Sub-Head : Flooring

86 11.41A Providing and laying Vitrified tiles in floor in different sizes

(thickness to be specified by the manufacturer) with water

absorption less than 0.08% and conforming to IS:15622, of

approved brand & manufacturer, in all colours and shade,

laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse

sand) jointing with grey cement slurry @3.3 kg/sqm

including grouting the joints with white cement and

matching pigments etc. The tiles must be cut with the zero

chipping diamond cutter only . Laying of tiles will be done

with the notch trowel, plier, wedge, clips of required

thickness, leveling system and rubber mallet for placing the

tiles gently and easily.

87 11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size

Digitally signed by PRIYA

Sl. No Description of Item Quantity Unit Rate (Rs) Amount(Rs)

89 11.46 Providing and laying Vitrified tiles in different sizes

(thickness to be specified by manufacturer) with water

absorption less than 0.08 % and conforming to I.S. 15622,

of approved make in all colours & shade in skirting, riser of

steps, over 12 mm thick bed of cement mortar 1:3

(1cement: 3 coarse sand), jointing with grey cement slurry

@ 3.3kg/sqm including grouting the joint with white

cement & matching pigments etc. complete.

92 16.75 Providing and laying C.C. pavement of mix M-25 with ready

mixed concrete from batching plant. The ready mixed

concrete shall be laid and finished with screed board

vibrator , vacuum dewatering process and finally finished

by floating, brooming with wire brush etc. complete as per

specifications and directions of Engineer-in charge. (The

panel shuttering work shall be paid for separately). (Note:-

Cement content considered in this item is @ 330 kg/cum.

Excess/less cement used as per design mix is payable/

recoverable separately).

93 11.4 52 mm thick cement concrete flooring with concrete

hardener topping, under layer 40 mm thick cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size) and top layer 12 mm thick

cement hardener consisting of mix 1:2 (1 cement hardener

mix : 2 graded stone aggregate 6 mm nominal size) by

volume, hardening compound mixed @ 2 litre per 50 kg of

cement or as per manufacturer’s specifications. This

includes cost of cement slurry, but excluding the cost of

nosing of steps etc. complete.

Total of the Sub-Head - Flooring : 14363315.83

Sub-Head : Roofing

93 12.45 Providing and fixing false ceiling at all height including

providing and fixing of frame work made of special

sections, power pressed from M.S. sheets and galvanized

with zinc coating of 120 gms/sqm (both side inclusive) as

per IS : 277 and consisting of angle cleats of size 25 mm

wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at

1200 mm centre to centre, one flange fixed to the ceiling

with dash fastener 12.5 mm dia x 50 mm long with 6 mm

dia bolts, other flange of cleat fixed to the angle hangers of

25x10x0.50 mm of required length with nuts & bolts of

required size and other end of angle hanger fixed with

intermediate G.I. channels 45x15x0.9 mm running at the

spacing of 1200 mm centre to centre, to which the ceiling

section 0.5 mm thick bottom wedge of 80 mm with

tapered flanges of 26 mm each having lips of 10.5 mm, at

450 mm centre to centre,

Digitally signed by PRIYA

Sl. No Description of Item Quantity Unit Rate (Rs) Amount(Rs)

shall be fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips made out of

2.64 mm dia x 230 mm long G.I. wire at every junction,

including fixing perimeter channels 0.5 mm thick 27 mm

high having flanges of 20 mm and 30 mm long, the

perimeter of ceiling fixed to wall/partition with the help of

rawl plugs at 450 mm centre, with 25mm long dry wall

screws @ 230 mm interval, including fixing of gypsum

board to ceiling section and perimeter channel with the

help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c,

including jointing and finishing to a flush finish of tapered

and square edges of the board with recommended jointing

compound , jointing tapes , finishing with jointing

compound in 3 layers covering upto 150 mm on both sides

of joint and two coats of primer suitable for board, all as

per manufacturer's specification and also including the

cost of making openings for light fittings, grills, diffusers,

cutouts made with frame of perimeter channels suitably

fixed, all complete as per drawings, specification and

direction of the Engineer in Charge but excluding the cost

of painting with :

94 12.45.1 12.5 mm thick tapered edge gypsum plain board

conforming to IS: 2095- (Part I) : 2011 (Board with BIS 65.00 Sqm 1451.11 94322.00

certification marks)

Total of the Sub-Head - Roofing : 94322.00

Sub-Head : Finishing

95 13.1 12 mm cement plaster of mix :

96 13.1.2 1:6 (1 cement: 6 fine sand)

97 13.2 15 mm cement plaster on the rough side of single or half

brick wall of mix :

98 13.2.2 1:6 (1 cement: 6 fine sand)

99 13.11 18 mm cement plaster in two coats under layer 12 mm

thick cement plaster 1:5 (1 cement: 5 coarse sand) finished

with a top layer 6mm thick cement plaster 1:6 (1 cement: 6

100 13.16 6 mm cement plaster of mix :

101 13.16.1 1:3 (1 cement: 3 fine sand)

102 13.26 Providing and applying plaster of paris putty of 2 mm

thickness over plastered surface to prepare the surface 2175.00 Sqm 281.17 611540.00

even and smooth complete.

103 13.45 Finishing walls with textured exterior paint of required

104 13.45.1 New work (Two or more coats applied @ 3.28 ltr/10 sqm)

over and including priming coat of exterior primer applied 1900.00 Sqm 239.32 454706.00

@2.20kg/10 sqm.

105 13.61 Painting with synthetic enamel paint of approved brand

and manufacture to give an even shade :

106 13.61.1 Two or more coats on new work. 2000.00 Sqm 166.86 333720.00

Digitally signed by PRIYA

Sl. No Description of Item Quantity Unit Rate (Rs) Amount(Rs)

107 13.83 Wall painting with premium acrylic emulsion paint of

interior grade, having VOC (Volatile Organic Compound )

content less than 50 grams/ litre. of approved brand and

manufacture, including applying additional coats wherever

required to achieve even shade and colour.

109 13.116 Polishing in high gloss/matt finish melamine clear polish on

wood work in required color/wooden shade texture with

following process in the sequence as detailed below:

110 1. The surface to be polished is rubbed with sand paper

80/120 no. and then with sand paper of 160/180 nos.

111 2. Applying two coats of sealer with spray gun and allowing

sufficient drying time for 1st coat and 2nd coat is allowed

to dry for 8 to 12 hrs.

112 3. On drying of sealer coat, wet rubbing with emery cloth

of finer grading with water to remove excess sealer layer

and make the surface further smooth after this wet

rubbing, then surface is applied with special grade

melamine fillers to fill all the small and big holes/grooves

etc. Filler coat to be allowed to dry for 4 to 6 hrs on which

again a light wet rubbing is done this surface is further

allowed to dry for 12 hrs.

113 4. On this, 1st coat of melamine polish is applied with

spray gun using melamine clear polish and melamine

thinner in required proportion. This 1st coat is allowed to

dry for 24 hrs then this dry surface is again fine wet rubbed

smooth, which is further allowed to dry for 12 hrs. The

final melamine polish is applied with compressor pressure

spray gun using melamine clear polish and melamine

thinner mixed in required proportion complete as per

direction of Engineer-in-Charge. (Finalo coat to be done in

1 or 2 layers without gap of time.)

Total of the Sub-Head - Finishing : 3590515.00

Sub-Head : Aluminium Work

114 21.1 Providing and fixing aluminium work for doors, windows,

ventilators and partitions with extruded built up standard

tubular sections/appropriate Z sections and other sections

of approved make conforming to IS: 733 and IS: 1285,

fixing with dash fasteners of required dia and size,

including necessary filling up the gaps at junctions, i.e. at

top, bottom and sides with required EPDM rubber/

neoprene gasket etc. Aluminium sections shall be smooth,

rust free, straight, mitred and jointed mechanically

wherever required including cleat angle, Aluminium snap

beading for glazing / paneling, C.P. brass/ stainless steel

screws, all complete as per architectural drawings and the

directions of Engineer-in-charge. (Glazing, paneling and

dash fasteners to be paid for separately) :

115 21.1.1 For fixed portion

116 21.1.1.2 Powder coated aluminium (minimum thickness of powder

coating 50 micron)

Digitally signed by PRIYA

Sl. No Description of Item Quantity Unit Rate (Rs) Amount(Rs)

117 21.1.2 For shutters of doors, windows & ventilators including

providing and fixing hinges/ pivots and making provision

for fixing of fittings wherever required including the cost of

EPDM rubber / neoprene gasket required (Fittings shall be

paid for separately).

118 21.1.2.2 Powder coated aluminium (minimum thickness of powder

coating 50 micron)

119 21.3 Providing and fixing glazing in aluminium door, window,

ventilator shutters and partitions etc. with EPDM rubber /

neoprene gasket etc. complete as per the architectural

drawings and the directions of engineer-in-charge . (Cost of

aluminium snap beading shall be paid in basic item):

120 21.3.3 With float glass panes of 8 mm thickness (weight not less

than 20 kg/sqm)

121 21.11 Providing and fixing stainless steel (SS 304 grade)

adjustable friction windows stays of approved quality with

necessary stainless steel screws etc. to the side hung

windows as per direction of Engineer-in-charge complete.

123 21.15 Providing and fixing aluminium casement windows

fastener of required length for aluminium windows with

necessary screws etc. complete.

124 21.15.2 Powder coated minimum thickness 50 micron aluminium.

Total of the Sub-Head - Aluminium Work : 831116.00

125 MR Dismantlling of existing facilities, Relocation of pipeline,

cable (Lumsum Payble) 1.00 job 800000.00 800000.00

Digitally signed by PRIYA

Name of Project : Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores

Department (SHED-1)

Name of Work : FIRE FIGHTING WORK

S.I MR DSR 2022 DSR 2022 MR

Description of Item Unit Total Qty

No Item No Item No Rate Amount Rate Amount

SUBHEAD I:FIRE HYDRANT SYSTEM

Providing, laying, testing & commissioning of 'C' class heavy

duty MS pipe conforming to IS 3589/IS 1239 including

Welding, fittings like elbows, tees, flanges, tapers, nuts bolts,

1 18.7 gaskets etc. and fixing the pipe on the wall/ceiling with

suitable clamp/support frame and painting with two or more

coats of synthetic enamel paint

of required shade complete as required :

Supplying and fixing single headed internal hydrant valve

with instantaneous Gunmetal/Stainless Steel coupling of 63

2 18.9 mm dia with cast iron wheel ISI marked conforming to IS 5290

(Type -A) with blank Gunmetal/Stainless teel cap and chain as

2.1 18.9.1 Single Headed Gunmetal Each 10 8183.514 ₹ 81,835.14

Supplying, fixing, testing and commissioning of butterfly valve

3 18.11 of PN 1.6 rating with bronze/gunmetal seat duly ISI

conforming to IS 13095 of following sizes as required :

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with

63 mm dia male and female couplings duly bound with GI

wire, rivets etc. conforming to IS 636 (type-A) as required:

Supplying and Fixing First Aid Hose Reel, wall mounting

swinging type complete with drum & bracket of MS

8 18.17 construction, spray painted in Post office Red, confirming to IS

884/1995 with upto date amendments, complete with the

following as required.

20 mm nominal internal dia as per IS 12585 water hose

thermoplastic (Textile reinforced)Type II as per IS: 12585

20 mm dia. ball valve & nozzle.

Drum and brackets for fixing the equipments on wall.

Connection from riser with 25 mm dia gun metal stop valve

and M.S pipe as reqd.

Supplying & fixing 63 mm dia gun metal short branch pipe

with 20 mm nominal internal diameter size nozzle conforming

to IS 903 suitable for instantaneous connection to

interconnect hose pipe coupling as required:

Supplying and fixing orifice plate made out of 6 mm thick

stainless steel(Grade 304) with orifice of required size to be

10 18.13 fitted between flange &landing valve of external and 10 1413.866 ₹ 14,138.66

internal hydrants to reduce presure at the outlet to the level

of 3.5 kg/sq.cm complete as required. Each

Providing and fixing standard fire man's axe with heavy duty

insulated rubber handle. Each 846.00 ₹ 8,460.00

Providing and fixing fire hose cabinet fabricated from 16

gauge M.S. Sheet with single or double glazed front door (with

13 NS-2 4 mm thick glass) and locking arrangement, painted fire red

with stove enamelled paint "FIRE HOSE" written on front

including necessary supports approximate size.

Providing and fixing dial type pressure gauge with isolation

cock and pipe at hydrant station.

14.1 NS-3.1 Diameter 100 mm calibration 0-8 Kg. Each 10 760.00 ₹ 7,600.00

Digitally signed by PRIYA

Name of Project : Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores

Department (SHED-1)

Name of Work : FIRE FIGHTING WORK

S.I MR DSR 2022 DSR 2022 MR

Description of Item Unit Total Qty

No Item No Item No Rate Amount Rate Amount

Providing and fixing CO2 type fire extinguishers with steel

15 NS-4 cylinder with a discharge valve and conforming to IS:15683. Each 35 3805.00 ₹ 1,33,175.00

Extinguishers shall be painted with rex enamel paint and fixed

to wall with brackets capacity 4.5 Kg.

Providing and fixing ABC powder type fire extinguisher

suitable for inverted operation and fabricated from 1.6 mm

M.S. sheet internally protected with anticorrosive treatment

and hydraulically tested to a pressure of 25 Kg/Sqcm.

Extinguishers externally painted with red enamel and fixed to

wall with brackets complete with internal charge and spanner

(Conforming to IS:15683 capaicity 6 KG.).

Digitally signed by PRIYA

Name of Project : Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department

PLUMBING WORKS DETAILED ESTIMATE

S.I DSR MR MR DSR

Description of Item Unit Total Qty

No Item No Item No Rate Amount Rate Amount

SUBHEAD-I(Sanitary Fixtures & CP Brass Fittings)

1 17.3 Providing and fixing white vitreous china pedestal type water

closet (European type) with seat and lid, 10 litre low level

white vitreous china flushing cistern & C.P. flush bend with

fittings & C.I. brackets, 40 mm flush bend, overflow

arrangement with specials of standard make and mosquito

proof coupling of approved municipal design complete,

including painting of fittings and brackets, cutting and making

good the walls and floors wherever required :

1.1 17.3.2 W.C. pan with ISI marked black solid plastic seat and lid Each 3 8427.86 25283.59

2 17.7 Providing and fixing wash basin with C.I. brackets, 15 mm C.P.

brass pillar taps, 32 mm C.P. brass waste of standard pattern,

including painting of fittings and brackets, cutting and making

good the walls wherever require:

2.1 17.7.2 White Vitreous China Wash basin size 630x450 mm with a

single 15 mm C.P. brass pillar tap

3 17.22A Providing and fixing CP Brass 32 mm size Bottle Trap of

approved quality & make and as per the direction of Engineer- Each 5.284860871 1107.55 5853.23

4 17.10 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen

sink as per IS:13983 with C.I. brackets and stainless steel plug

40 mm, including painting of fittings and brackets, cutting and

making good the walls wherever required:

4.1 17.10.1 Kitchen sink with drain board

5 NS-6 Fixing of 15 mm C.P brass wall mounted mixing fittings

swinging spout for sink complete including cutting and

making good the walls where required. (Pantry, Kitchen,

Coffee-Break etc.)

6 17.4 Providing and fixing white vitreous china flat back or wall

corner type lipped front urinal basin of 430x260x350 mm and

340x410x265 mm sizes respectively with automatic flushing

cistern with standard flush pipe and C.P. brass spreaders with

brass unions and G.I clamps complete, including painting of

fittings and brackets, cutting and making good the walls and

floors wherever required :

6.1 17.4.1 One urinal basin with 5 litre white P.V.C. automatic flushing 2

7 NS-7 Providing and fixing in postion storage type automatic electric

water heater pressure type thermostatically controlled, single

phase wall mounted of approved make (to the approval of

Engineer-in-charge) with thermostats, inner container of

stainless steel, Inner glass lining with B-Rating minimum 3

stars complete with 1 Mtr. three core flexible cord with plug,

non return valve and pressure release valve complete

including fixing and testing complete in all respect.

7.1 15 litre capacity water heater Each 1 13470.00 13470.00

8 NS-8 Providing & fixing in position Water Cooler without Stablizer

of approved make (to the approval of Engineer-in-charge )

including carriage complete in all respect.

Each RO 46170.00

Water Cooler Full Steel Body 40 ltr Capacity without Stablizer

9 17.16A Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube

upto 1 metre long with S.S. triangular plate to Eureopean type

W.C. of quality and make as approved by Engineer - in -

10 18.53 Providing and fixing C.P. brass angle valve for basin mixer and

geyser points of approved quality conforming to IS:8931 Each 14 614.67 8605.43

11 17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin

11.1 17.28.2 Flexible pipe

Digitally signed by PRIYA

Name of Project : Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department

PLUMBING WORKS DETAILED ESTIMATE

S.I DSR MR MR DSR

Description of Item Unit Total Qty

No Item No Item No Rate Amount Rate Amount

12 NS-9 Providing & Fixing in position C.P. Brass coat hook of

approved make (to the approval of Engineer-in-charge ) fixed

into wall with C.P. brass screws and rawl plugs etc. complete

in all respect.

12.1 C.P.Brass coat hook Each 4 962.00 3848.00

13 17.31 Providing and fixing 600x900 mm beveled edge mirror of 2

superior glass (of approved quality) complete with 6 mm thick

hard board ground fixed to wooden cleats with C.P. brass

screws and washers complete.

14 17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 2

mm long, 200 mm wide with minimum distances of 37 mm

from wall face with concealed fittings arrangement of

approved quality and colour, weighing not less than 88 gms.

15 17.71 Providing and fixing PTMT liquid soap container 109 mm 2

wide, 125 mm high and 112 mm distance from wall of

standard shape with bracket of the same materials with snap Each 180.19 360.37

fittings of approved quality and colour, weighing not less than

SUBHEAD II(Soil, Waste, Vent & Rain Water Pipes)

16 NS-10 Supply, installation , testing commissioning of PP Mineral

filled low noise Soil & Waste system as per EN 12056,

with density 1.9 g/cm3. PP mineral(Astolan) filled Low noise

system should has a fire classification DIN 4102-

B2/EN13501 . Product should have a chemical resistance of

pH 2-12 and is a complete sound protection system

according to DIN 4109. including with push fit rubber ring

sockets all necessary fittings and specials such as Bends,

junctions, offsets & vent cowl. Fixing at wall/ceiling level

supported by rubber line bracket & hangers etc. duly epoxy

coated. Cutting, chases/holes in floors / walls /

slab.Compliant with LABC. Weight mass per unit area of

DN100MM should not be less than 110.07kg/m3. sound

levels of not more than 15dBA as per EN 14366 at a flow

rate of 4 l/s.including all core cut ,chases ,cutting making

holes in all wall and floor as required complete in all respect.

17 NS-11 Providing fixing, testing and commissioning in position Solfit

SWR uPVC PIPE TYPE-B pipe comforming to IS:13592

including all fittings such as bends, junctions, inspection doors,

offests, cowl, access pieces/clean out plugs, clamps /supports/

hangers etc. jointing with PVC Adhesive joints including

cutting holes in walls, core cutting in slabs and making good

the same. All complete as per specification and direction of

E/l.(For rainwater piping)

18 NS-12 Providing Fixing straight /offset type single body push fit type WC

pan connector with factory supplied spring loaded seal

guard with integral single mould sealing fins made of flexible Each 4 800.00 3200.00

EVA body, including bush/adaptor as supplied with the pan

connector (if required).

Providing and fixing floor drain (FD) with 50mm/40mm outlet

and one 40mm inlet for waste, with SS grating (adjustable Each 2 450.41 900.82

height), having 50mm water seal and in-built NRV

20 NS-14 Providing and fixing PP/UPVC trap of self cleansing design with

screwed down or hinged grating with or without vent arm complete,

including cost of cutting and making good the walls and floors :

20.1 NS-14.1 100 mm inlet and 100 mm outlet

20.1.1 NS-14.1.1 Sand cast iron S&S as per IS: 3989 Each 6 3986.29 23917.77

21 NS-15 Providing and fixing PP/UPVC grating with Cockroach proof

strainer of approved design including setting in floor with

cement motor to match with floor finish as per architect

requirement suitable for waster and FT.

Digitally signed by PRIYA

Name of Project : Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department

PLUMBING WORKS DETAILED ESTIMATE

S.I DSR MR MR DSR

Description of Item Unit Total Qty

No Item No Item No Rate Amount Rate Amount

22 NS-16 Providing and fixing PP/UPVC brass grating with frame of

approved design including setting in floor with cement motor

to match with floor finish as per architect requirement.

23 NS-17 Providing and fixing PP/UPVC extention piece for 100 mm dia

floor trap formed out of main pipe with multiple side inlets,

suitable for various dia pipes including all fixtures as required Each 6 2508.45 15050.69

complete as per drawing approved sample and direction of

engineer in charge.

24 NS-18 Providing and fixing cast PP floor clean out plug with

suitable insert keys for opening, male threaded joint with

threaded socket drip seal to soil / waste pipe as required Each 4 1769.53 7078.10

complete as per drawing approved sample and direction of

engineer in charge.

24.1 NS-19 Size 100 mm X 100 mm

SUBHEAD III(Water Supply System(Internal))

26 18.8 NS-20 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings and fixing

the pipe with clamps at 1.00 m spacing. This includes jointing

of pipes & fittings with one step CPVC solvent cement and the

cost of cutting chases and making good the same including

testing of joints complete as per direction of Engineer in

Concealed work, including cutting chases and making good

the walls etc(inside building)

26.1 18.8.1 15 mm nominal dia Pipes Mtr 15 532.80 7991.93

26.2 18.8.2 20 mm nominal dia Pipes Mtr 20 575.39 11507.87

26.3 18.8.3 25 mm nominal dia Pipes Mtr 65 671.35 43637.47

28 18.18 Providing and fixing ball valve (brass) of approved quality,

High or low pressure, with plastic floats complete :

28.2 18.18.2 20 mm nominal dia Pipes Each 1 495.01 495.01

28.3 18.18.3 25 mm nominal dia Pipes Each 2 496.67 993.35

29 18.17 Providing and fixing gun metal gate valve with C.I. wheel of

approved quality (screwed end) :

SUBHEAD IV(External Sewerage & Storm Water Drainage)

34 19.6 Providing and laying non-pressure NP2 class (light duty) R.C.C.

pipes with collars jointed with stiff mixture of cement mortar in the

proportion of 1:2 (1 cement : 2 fine sand) including testing of joints

etc. complete :

Providing, laying and jointing glazed stoneware pipes class SP-1

with stiff mixture of cement mortar in the proportion of 1:1 (1

cement : 1 fine sand) including testing of joints etc. complete :

36 19.7 Constructing brick masonry manhole in cement mortar 1:4 ( 1

cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1

cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20

mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4

coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal

size), inside plastering 12 mm thick with cement mortar 1:3 (1

cement : 3 coarse sand) finished with floating coat of neat cement

and making channels in cement concrete 1:2:4 (1 cement : 2

coarse sand : 4 graded stone aggregate 20 mm nominal size)

finished with a floating coat of neat cement complete as per

standard design :

36.1 19.7.1 Inside size 90x80 cm and 45 cm deep including C.I. cover with

frame (light duty) 455x610 mm internal dimensions, total weight of

cover and frame to be not less than 38 kg (weight of cover 23 kg

and weight of frame 15 kg) :

36.2 19.7.1.2 With Sewer bricks conforming to IS : 4885 Each 6 13605.44 81632.64

37 19.4 Providing and fixing square-mouth S.W. gully trap class SP-1

complete with C.I. grating brick masonry chamber with water tight

C.I. cover with frame of 300 x 300 mm size (inside) the weight of

cover to be not less than 4.50 kg and frame to be not less than

2.70 kg as per standard design:

37.1 19.4.1 100x100 mm size P type

Digitally signed by PRIYA

Name of Project : Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department

PLUMBING WORKS DETAILED ESTIMATE

S.I DSR MR MR DSR

Description of Item Unit Total Qty

No Item No Item No Rate Amount Rate Amount

37.2 19.4.1.1 With common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 Each

38 NS-21 Constructing catch basin 45x45 cm with bricks in cement

mortar 1:4 (1 cement : 4 coarse sand) including 500x450

mm pre-cast R.C.C. horizontal grating with frame complete

as per standard design :

38.2 NS-21.1 With common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 Each

Providing orange colour safety foot rest of minimum 6 mm thick

plastic encapsulated as per IS : 10910, on 12 mm dia steel bar

conforming to IS: 1786, having minimum cross section as 23

mmx25 mm and over all minimum length 263 mm and width as

165 mm with minimum 112 mm space between protruded legs

having 2 mm tread on top surface by ribbing or chequering besides

necessary and adequate anchoring projections on tail length on

138 mm as per standard drawing and suitable to with stand the

bend test and chemical resistance test as per specifications and

having manufacture’s permanent identification mark to be visible

even after fixing, including fixing in manholes with 30x20x15 cm

cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded

stone aggregate 20 mm nominal size) complete as per design. Each 18

40 19.21 Making connection of drain or sewer line with existing

manhole including breaking into and making good the walls, floors

with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal size) cement plastered on

both sides with cement mortar 1:3 (1 cement : 3 coarse sand),

finished with a floating coat of neat cement and making necessary

channels for the drain etc. complete :

40.1 19.21.1 For pipes 100 to 250 mm diameter Each 2 867.42 1734.85

SUBHEAD V(External Water Supply)

41 18.12 Providing and fixing G.I. pipes complete with G.I. fittings including

trenching and refilling etc.

42 18.40 Painting G.I. pipes and fittings with two coats of anti-corrosive

bitumastic paint of approved quality :

Fixing water meter and stop cock in G.I. pipe line including cutting

and threading the pipe and making long screws etc. complete (cost 869.40 1738.81

of water meter and stop cock to be paid separately). Each 2

44 18.37 Constructing masonry Chamber 60x45x50 cm inside, in brick work

in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter

complete with C.I. double flap surface box 400x200x200 mm

(inside) with locking arrangement and RCC top slab 1:1.5:3 mix (1

cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm

nominal size), including necessary excavation, foundation concrete 10380.36 20760.72

1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm

nominal size) and inside plastering with cement mortar 1:3 (1

cement : 3 coarse sand) 12 mm thick, finished with a floating coat

of neat cement complete as per standard design :

Digitally signed by PRIYA

NAME OF WORK: Construction of 250mx30m of shed with EOT Crane facility in General Store Area of MM- Stores Department (SHED - 1)

PEB WORK DETAIL

Sl. No Item No Description of Item Quantity Unit Rate Amount

1 NS -22 Built-up sections are made from hot rolled plates conforming to ASTM A-572 Grade 50/ IS :2062

E350 (Min Yield strength 345 MPa) steel or equivalent Grade steel. Alkyd based direct to metal

paint shall be applied in plant with an average dry film thickness of 90 micron on all finished

structural steel. At site, only touchup will be done with paint of same specification and colour

against any transportation and handling scratches / damages. Hot rolled sections are mill sections

complying with IS:2062 Grade E 250 steel ( Min. Yield

strength 240 MPa).

ERW pipes are as per IS:1161 Grade YST 210/240 ( Min. Yield Strength 210 Mpa / 240 Mpa).

Channels for crane beams/ Gantary Girder (all Complete) are mill formed sections conforming to

IS:2062 Grade E250 steel (Min Yield strength 240 MPa). Galvanized cold formed sections of 683.43 M.T 1,10,000.00 ₹ 7,51,77,531

thickness 2.0 mm are made from galvanized coils as per ASTM A 653 Structural steel ( SS) Grade

50 Class 1 / IS :277 GP 350 (Min. Yield strength 345 Mpa).

Bracing rods are made from steel bars conforming to IS:2062 Grade E 250 (Min. yield strength of

Lateral bracing angle+B35s ( galvanized ) are made from steel coils conforming to ASTM A 653

Structural steel ( SS) Grade 50 Class 1 ( Min. Yield strength 345 Mpa ) / IS :277 GP 350 . Lateral

Bracing rods conforming to IS: 2062 Grade E 250 ( Minimum yield strength 240mpa ) can be used.

2 NS -23 Providing and fixing 0.58mm TCT Standing Seam Profile sheeting for roofing of same colour as

per exsisting (RAL), comprising zinc aluminium alloy coated steel of base metal thickness of 0.53

mm having yield strength of min. 300 MPa and zinc aluminium coating of 150 gsm as per AS :

1397 (total of both sides) and permanently colour coated with 20 microns SDP Colour Coating

over a 5 micron primer and back coat of 5 micron over a 5 micron primer coat. The Standing Seam 8250.00 SQM 1,100.00 ₹ 90,75,000

roofing features a unique concealed clip made from GI, one portion of the clip (lower) is fastened

to the steel structure (purlin) and the upper part gets attached to the roofing sheet. Thereafter the

sheet panel along with concealed clip is crimped / locked together by a mechanical zipping

machine and provides an absolutely puncture less roof.

3 NS -24 Rockwool Insulation for roof area as per IS: 8183 in roll form without or with a vapour barrier (foil

scrim Kraft (FSK). Rock wool insulation density shall not be less than 48 Kg/m3. Also below the 8250.00 SQM 350.00 ₹ 28,87,500

insulation weldmesh is required 75x75x2mm.

4 NS-25 Providing and fixing 2mm thick “C” profiled Polycarbonate sheet as Skylight with suitable metal

capping. The Skylight shall be fixed to the standing seam roofing as per design, drawing all 430.00 SQM 1,200.00 ₹ 5,16,000

complete as per manufacturers specifications and for all heights and levels.

5 NS-26 Providing and fixing 3mm thick prepainted MS gutters with 2mm thick FRP lining of required size

over the already provided structural support with suitable down pipes at distances mentioned all 825.00 RMT 7,200.00 ₹ 59,40,000

complete as per design & drawing.

6 NS-27 Providing and fixing PVC downtake pipe at distances mentioned all complete as per design &

7 NS-28 Providing and fixing permanently colour coated profile sheets of the same colour as per exsisting

(RAL) of depth 28 - 30 mm at minimum 195 - 200 mm pitch distance to the girt and fixed with self

drilling galvanized fasteners. Profiled sheets shall be min. 0.5mm TCT high tensile Zinc aluminium

alloy coated steel sheet having yield strength of 550 MPa with a coating mass of 150 gsm zinc-

aluminium coating total of both sides as per AS 1397 : 1993 and finished with 20 microns colour

coating of SDP paint coat on exposed surface over a primer coat of 5 microns of approved colour

and a back coat of 5 microns on reverse side over a 5 microns primer coat. There shall be 2 small 7500 SQM 820.00 ₹ 61,50,000

ribs between the profiles to give additional strength. The sheet to be fixed over the girts with

hexagonal head self drilling fasteners including neoprene / EPDM washer on each crest of

sheet. The work shall include, erection of all fasteners, flashing etc. made out of 0.5mm colour

coated zinc aluminium alloy coated steel of same specs as above. The profile steel sheets shall

conform to IS: 513, 277 & 14246. Make - TATABluescope

8 NS-29 Rockwool Insulation for roof area as per IS: 8183 in roll form without or with a vapour barrier (foil

scrim Kraft (FSK). Rock wool insulation density shall not be less than 48 Kg/m3. Also below the 7500 SQM 350.00 ₹ 26,25,000

insulation weldmesh is required 75x75x2mm

9 NS-30 Interarch VL-2 type fixed louvers shall be manufactured out of 0.5mm TCT SDP coated Galvalume

sheet in white colour with insect screen and is supplied in standard modules of 1500 mm wide x 320 SQM 4200.00 ₹ 13,44,000

Total carried over to summary: ₹ 10,51,85,031.00

Digitally signed by PRIYA

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department (SHED-1 )

Sl. No Item Description of Item Quantity Unit Rate Amount

Supply, Installation, Testing & Commissioning of of Double Girder Box Type E.O.T. (Electric

Overhead Travelling) Crane running on same Bay and same level, Box Type Fabrication having Rated

Capacity 25 Tons (Main) / 10 Tons (Auxiliary.) (Safe Working Load) having Span 30 meters and lift

height 9 meters (Adjustable as per site conditions) is a robust and high-performance lifting solution 2 No ₹ 69,12,467.00 ₹ 1,38,24,934.00

engineered for heavy-duty industrial applications. Designed in accordance with IS 807 and IS 4137

standards, this crane offers superior durability, operational efficiency, and safety including Square Bar for

Construction & Components: Main Girder - Box-type fabricated from high-grade MS plates as per IS

3177, End Carriage - Fabricated to IS 800 and IS 807 standards for structural integrity, Wire Rope - 16

mm diameter, 6x36 construction, Usha Martin make, Hook: Swiveling C-type hook as per IS 3815, pulley-

mounted, Full Platform provided on one side, Electrically powered trolley

Operational Details: Fall Configuration: 25 T Main Hoist Wire Rope: 16 mm, 6 x 36 construction, 8-

falls system, 10 T Aux. Hoist Wire Rope: 16 MM, 6 x 36 construction, 4-falls system, Hoist Duty Class:

Class 2 as per IS 3177 / IS 807, Performance Speeds: Main Hoisting Speed: 0.3 – 3.0 m/min, Cross

Travel Speed: 1.5 – 20 m/min, Long Travel Speed: 0.2 – 20 m/min

Operation Control: Crane can be move manualy (cabin for crane operator) or by usingFloor-level

pendant push button station (independently moving) with emergency stop and wirelessly by using radio

remote control (RRC) operating system

Crane Electrical Control Panel: Mounted on the bridge platform in an IP44 enclosure.Houses Variable

Frequency Drives (VFD) for all motion drives to ensure smooth acceleration and dual-speed operation,

equipped with Schneider Switchgear components,Cross Travel (CT) power fed via a flexible Festoon

Cable system, Fitted with limit switches for Hoisting, Cross Travel, and Long Travel.

Drive & Motor Details: Motor Type: Squirrel Cage Induction Motor, Crane Duty (3-phase),

Foot/Flange/Face Mounted, Motor Ratings: Hoisting: Mimimum 30 H.P.(Main) & 10 H.P. (Aux.), Cross

Travel: 3 H.P. x 2 ,Long Travel: 5 H.P. x 2 nos, Braking System: Hoisting: EHT Thruster Brake, Cross &

Long Travel: DC Brakes, Gearbox & Mechanism: Heavy-duty, totally enclosed helical gearboxes with

splash lubrication (alloy steel helical gears, stress-relieved MS body), Hook: Swiveling C-type Hook with

NS-31 pulley (IS 3815) using alloy steel components. Additional Features: Rope Drum: Made from MS

seamless pipe, Control Panel: In-house make with Schneider components, IP 44 rated, mounted on an

accessible platform, Platform: Full platform provided on one side, Travel Mechanism: Electrically

powered trolley, Wheels: LT & CT Wheels: Double flanged wheels made of En8/En9 steel (Hardness:

200–250 BHN), 250 mm dia, flanged, Paint & Finish: Two coats of primer followed by two coats of golden

yellow paint (RAL 1004) ensure long-lasting corrosion resistance and aesthetics. (RYBG long travel power

On-Ground & Facility Electrical Systems

1. Main Incomer Power & Floor Switchgear.

Main Wall-Mounted Incomer Switch/MCCB: A 3-phase, 415 V, 50 Hz, 125 A–160 A MCCB panel with

an isolated door-interlocked Isolator Switch, installed at ground level near the center or start of the 250

Ground Isolation Emergency Stop: An easily accessible lockable Isolator Switch at floor level to de-

energize the entire crane runway during maintenance.

2. Long Travel Power Conductor System (DSL System)

4-Pole Shrouded/Insulated DSL Conductor Bars (RYBG): A 250-meter long Down-Shop Lead (DSL)

shrouded busbar system running along the gantry girder rail (R-Y-B Phases + Earth) rated for a

minimum of 125 A–200 A.

Center Power Feed Terminal: Located at the 125 m mark of the 250 m run to minimize voltage drop

along the runway.

Current Collectors: Heavy-duty spring-loaded dual current collector arm assemblies mounted on the

crane's end carriage.

3. Ground-to-Gantry Power Wiring & Cabling

Main Feed Cable: Armored XLPE insulated 4-Core Copper/Aluminum cable (minimum $3.5\text{C}

\times 35\text{ sq.mm}$ or $50\text{ sq.mm}$) laid from the main floor electrical panel to the DSL

busbar power feed box.

Containment: Heavy-duty GI cable trays, rigid conduits, or underground trenches running up the bay

column to the gantry level.

4. Grounding & Earthing System

Dedicated Earth Pit: Minimum 2 dedicated chemical/copper plate earthing pits (< 2 Ohms earth

Earth Conductor: Twin continuous 25 x 3 mm GI earthing flats running from the floor earth pits to the

crane gantry structure and connected directly to the protective conductor of the DSL system.

Digitally signed by PRIYA

(SCHEDULE OF QUANTITIES)

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department

S.No. Description Unit Qty

DSR 2022 (In Rs.) (In Rs.)

A SCHEDULE ITEMS

WIRING AND SUB MAINS

Wiring for light point/ fan point/ exhaust fan point/ call bell point with

1.5 sq.mm FRLS PVC insulated copper conductor single core cable in

surface / recessed heavy class Steel conduit, with modular switch,

modular plate, suitable GI box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc as

required.a) Group C

Wiring for MCB Controlled light point/ fan point/ exhaust fan point/ call

bell point with 2.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed FRLS Heavy Duty PVC

conduit, and earthing the point with 2.5 sq.mm. FRLS PVC insulated

copper conductor single core cable etc as required.(Cost of MCB not

to be included in this item)

a 1.14.2 x10 Primary Point Points 63 2943.33 185429.48

b 1.14.2 x4 Loop Point Points 564 1177.33 664014.12

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface / recessed Steel

3 1.2 conduit, 2 way modular switch, modular plate, suitable GI box and Point 2 1964.00 3928.00

earthing the point with 1.5 sq.mm. FRLS PVC insulated copper

conductor single core cable etc as required

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated

copper conductor single core cable in surface/ recessed Steel conduit

alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor

single core cable for loop earthing as required

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated

copper conductor single core cable in surface/ recessed Steel conduit

alongwith 2 Nos 4 sq. mm FRLS PVC insulated copper conductor

single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the

6 1.7 following sizes of FRLS PVC insulated copper conductor, single core

cable in surface/ recessed Steel conduit as required.

a 1.7.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire metre 100 394.94 39494.07

b 1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire metre 10 458.09 4580.88

b 1.7.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire metre 10 630.41 6304.07

d 1.7.5 2 X 10 sq. mm + 1 X 6 sq. mm earth wire metre 5 759.91 3799.57

e 1.7.9 4 X 6 sq. mm + 2 X 6 sq. mm earth wire metre 35 988.96 34613.50

f 1.7.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire metre 600 1247.97 748781.88

g 1.7.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire metre 400 1760.64 704257.40

Supplying and fixing suitable size GI box with modular plate and cover

in front on surface or in recess, including providing and fixing 3 pin 5/6

7 1.31 amps modular socket outlet and 5/6 amps modular switch, connection Each 6 510.53 3063.20

etc. as required. (For light plugs to be used in non residential

Supplying and fixing suitable size GI box with modular plate and cover

in front on surface or in recess, including providing and fixing 6 pin

15/16 amps modular socket outlet and 15/16 amps modular switch,

connection etc. as required.

9 Supplying and fixing of following modular switch/ socket outlet on the

5/6 ampsModular

switch plate & switch including connection but excluding

b 1.24.4 3 pin 5/6 amp socket outlet Each 10 130.58 1305.77

d 1.24.5 6 pin 15/16 amp socket outlet Each 2 210.85 421.70

e 25 amp switch Each 1 214.06 214.06

10 1.27 Supplying and fixing following size/ modules, GI box Boxes alongwith

1 or 2 Module cover plate for modular switches in recess etc as

Digitally signed by PRIYA

(SCHEDULE OF QUANTITIES)

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department

S.No. Description Unit Qty

DSR 2022 (In Rs.) (In Rs.)

11 2.18 Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket

outlet, with 2 pole and earth, metal enclosed plug top along with 20

amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or

in recess, with chained metal cover for the socket out let and Each 1 1734.96 1734.96

complete with connections, testing and commissioning etc. as

12 1.25 Supplying and fixing stepped fan regulator on the existing modular

plate switch box including connections but excluding modular plate Nos. 6 394.94 2369.64

etc. as required.

13 MR Supplying and fixing of 16 SWG M.S. Fan Box 12.5" Rod but without

fan cover (hylam sheet). as required.

14 MR Supplying and fixing of fan cover (hylam sheet).on the existing Fan

Box as required.

15 Supplying and fixing of modular Blanking plate on the existing modular

plate & switch box excluding modular plate etc. as reqd.

16 1.24 Supply and fixing following modular switch/socket on the existing

modular plate and cover plate & switch box including connections but

excluding modular plate etc. as required.

a 1.24.6 Telephone socket outlet. (RJ - 11) Each 5 158.40 792.02

b 1.24.7 TV antenna socket outlet Each 1 158.40 158.40

17 1.27 Supplying and fixing following size/modules, GI box along with

modular base and cover plate for modular switches in recess etc as

19 1.18 Supplying and drawing following pair, 0.5 sq.mm FR PVC insulated

copper conductor, unarmoured telephone cable in the existing surface

/ recessed steel / PVC conduit as required.

20 1.27.1 Supply, laying, testing and commissioning of the following co-axial

PVC insulated conductor cable in existing surface / recessed conduit

etc. and including making terminal joints, complete as required.

21 1.53 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing

surface/ recessed Steel/ PVC conduit/ raceway as required.

Supplying and fixing of following sizes of steel conduit along with

accessories in surface/recess including painting in case of surface

conduit, or cutting the wall and making good the same in case of

recessed conduit as required.

Supplying and fixing of following sizes of heavy class PVC conduit

23 1.21 along with accessories in surface/recess including cutting the wall and

making good the same in case of recessed conduit as required.

Digitally signed by PRIYA

(SCHEDULE OF QUANTITIES)

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department

S.No. Description Unit Qty

DSR 2022 (In Rs.) (In Rs.)

DISTRIBUTION BOARDS

Supplying and fixing following way, Horizontal type three pole and

neutral, sheet steel, MCB distribution board, 415 volts, on

24 surface/recess, complete with tinned copper bus bar, neutral bus bar,

interconnections, powder painted including earthing etc. as required.

(But without MCB/RCCB/Isolator)

a 2.4.1 4 way (4 + 12), Double door, Horizontal Each 2 4378.60 8757.19

b 2.4.2 6 way (4 + 18) ,Double door, Horizontal Each 2 5323.67 10647.34

c 2.4.3 8 way (4 + 24), Double door, Horizontal Each 24 6386.48 153275.52

Supplying and fixing following rating, four pole, 415 volts, isolator in

25 2.13 the existing MCB DB complete with connections, testing and

commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and

neutral), 240 volts, residual current circuit breaker (RCCB), having a

26 2.14 sensitivity current upto 30 milliamperes in the existing MCB DB

complete with connections, testing and commissioning etc. as

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve,

miniature circuit breaker suitable for inductive load of following poles in

the existing MCB DB complete with connections, testing and

commissioning etc. as required.

Supplying and fixing single pole blanking plate in the existing MCB DB

complete etc. as required.

ERRECTION OF FAN & FIXTURE

Installation ,Testing, Commissioning of wall bracket fittings of all sizes

29 1.33 and shapes including LED lamps per fitting, complete with all each 2 93.12 186.23

accessories including connections etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent

fitting / compact fluorescent fitting / LED Fittings of all types,

30 1.41 with all accessories and tube etc. directly on ceiling/ wall, each 11 220.48 2425.30

including connection with 1.5 sq. mm FR PVC insulated, copper

conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent

fitting / compact fluorescent fitting / LED Fittings of all types and

31 MR shape, with all accessories and tube etc. on falsceiling including each 6.4218 250.00 1605.45

connection with 1.5 sq. mm FR PVC insulated, copper conductor,

single core cable and earthing etc. as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep,

BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC)

Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2

nos. canopies, shackle kit, safety rope, copper winding, Power Factor

not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery

32 19.1 minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), each 6 2921.92 17531.51

THD less than 10%, remote or electronic regulator unit for speed

control and all remaining accessories including safety pin, nut bolts,

washers, temperature rise=75 degree C (max.), insulation resistance

more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC

Supply, earthing etc. complete as required.

Installation of exhaust fan in the existing opening, including

33 1.5 making good the damage, connection, testing, commissioning etc.

a 1.50.1 Upto 450 mm sweep each 1 481.64 481.64

Digitally signed by PRIYA

(SCHEDULE OF QUANTITIES)

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department

S.No. Description Unit Qty

DSR 2022 (In Rs.) (In Rs.)

b 1.50.2 Upto 510 mm sweep each 1 688.20 688.20

Extra for fixing the louvers/ shutters complete with frame for a

exhaust fan of all sizes.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including

accessories, and providing masonry enclosure with cover plate having

35 5.2 locking arrangement and watering pipe etc. with charcoal/coke and Nos. 12 7336.91 88042.88

salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with cover

plate having locking arrangement and watering pipe of 2.7 metre long

etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick

including accessories, and providing masonry enclosure with cover

plate having locking arrangement and watering pipe of 2.7 metre long

etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess

for connections etc. as required.

Providing and fixing 25 mm X 5 mm Copper. strip on surface or in

recess for connections etc. as required.

5.18 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for

40 loop earthing along with existing surface/ recessed conduit/ submain Mtr 400 44.95 17981.04

wiring/ cable as required

6.2 Providing and fixing of lightning conductor finial, made of 25 mm dia

300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6

mm thick G.I. base plate including holes etc. complete as required.

6.7 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or on

42 surface of wall for lightning conductor and external lighting complete Mtr 750 134.86 101143.35

as required. (For Horizontal run)

6.8 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or on

43 surface of wall for lightning conductor complete as required. (For Mtr 150 210.85 31627.37

6.12 Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I.

44 strip, 125 mm long, with 4 Nos. of G.I. bolts, nuts, chuck nuts and Set 12 129.51 1554.08

spring washers etc. complete as required.

INTELLIGENT FIRE DETECTION AND ALARM SYSTEM

17.2.1 Supplying, installation, testing and commissioning of micro processor

based intelligent addressable main fire alarm panel, central

processing unit with the following loop modules and capable of

supporting not less than 240 devices (including detectors) and

minimum 120 detectors per loop and loop length up to 2 km, network

communication card, minimum 320 character graphics/ LCD display

with touch screen or other keypad and minimum 4000 events history

log in the non volatile memory (EPROM), power supply unit (230 ± 5%

45 V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free

batteries with automatic charger. The panel shall have facility to

connect printer to printout log and facility to have seamless integration

with analog/digital voice evacuation system (which is part of the

schedule of work under SH: PA System) and shall be complete with all

accessories . The panel shall be compatible for IBMS system with

open protocol BACnet/ Modbus over IP complete as per

17.2.9 Supplying, installation, testing & commissioning of intelligent

46 addressable thermal detector with rate of rise cum fixed tempreature Each 2 2917.64 5835.28

thermistor complete with base as required.

17.2.4 Supplying, installation, testing & commissioning of intelligent analog

47 addressable photothermal detector complete with mounting base Each 4 3058.92 12235.67

complete as required.

Digitally signed by PRIYA

(SCHEDULE OF QUANTITIES)

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department

S.No. Description Unit Qty

DSR 2022 (In Rs.) (In Rs.)

17:02:12 Supplying, installation, testing & commissioning of

addressable beam detector with short circuit isolator (inbuilt

or seperate) complete with emitter and receiver including Each 10 80205.07 802050.71

connections with remote test features etc complete as

17.2.5 Supplying, installation, testing & commissioning of response indicator

48 on surface/recessed MS Box having two LED, metallic cover complete Each 20 295.40 5908.06

with all connections etc as required.

17.2.14 Supplying, installation, testing & commissioning of

addressable manual call point complete as required.

17.2.15 Supplying, installation, testing & commissioning of

addressable horn cum strobe complete as required.

17.2.7 Supplying, installation, testing & commissioning of fault

isolator complete with base as required.

17.2.10 Supplying, installation, testing & commissioning of

addressable fire control module complete as required

17.2.11 Supplying, installation, testing & commissioning of

addressable phone control module complete as required.

17.2.17 Supplying, installation, testing & commissioning of fire fighter

telephone handset complete as required.

17.5.2 Supplying & laying of 2x1.5 sqmm fire alarm armoured cable,

600/1000V rated with annealed copper conductor having XLPE

insulation, steel wire armouring & FRLS outer sheath complete as

Cable End Termination & Pipes

Supplying and making ends termination with brass compression

glands and aluminium lugs for following size of PVC insulated PVC

sheathed aluminiumconductor cable of 1.1 KV grade as required .

Providing, laying and jointing PVC/RCC NP-2 pipe with Vin stiff

mixture of cement mortar in the proportion of 1:2 (1 cement:2 fine

sand) including trenching (75 cm deep / or as required) i/c testing the

joints etc. in loose soil/under the flooring (before laying the finished

flooring) for electrical cable entrance to the building complete as

required i/c excavation and refilling of earth.

Supplying and laying of following size DWC HDPE pipe ISI marked

along with all accessories like socket, bend, couplers etc. conforming

to IS 14930, Part II complete with fitting and cutting, jointing etc.direct

in ground (75 cm below ground level) including excavation and refilling

the trench but excluding sand cushioning and protective covering etc.,

complete as required.

a 14.16.1 63 mm dia (OD-63 mm & ID-51 mm nominal) metre 200 264.36 52872.82

b 14.16.2 90 mm dia (OD-90 mm & ID-76 mm nominal) metre 5 310.39 1551.94

c 14.16.3 120 mm dia (OD-120 mm & ID-103 mm nominal) metre 5 393.87 1969.35

d 14.16.4 160 mm dia (OD-160 mm & ID-135 mm nominal) metre 15 514.81 7722.21

e 14.16.5 200 mm dia (OD-200 mm & ID-175 mm nominal) metre 100 714.96 71496.04

Digitally signed by PRIYA

(SCHEDULE OF QUANTITIES)

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department

S.No. Description Unit Qty

DSR 2022 (In Rs.) (In Rs.)

Digitally signed by PRIYA

(SCHEDULE OF QUANTITIES)

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department

S.No. Description Unit Qty

DSR 2022 (In Rs.) (In Rs.)

B NON SCHEDULE ITEMS

DATA /TELEPHONE / EPBX

Supply and fixing following modular switch/socket on the existing

59 modular plate and cover plate & switch box including connections but

excluding modular plate etc. as required.

a Information Socket Outlet RJ -45 suitable for CAT 6 Data Each 5 825.00 4125.00

Supply installation testing and commissioning of MDF (Krone) &

60 Connecting Cable (3 x 16) Each 1 8500.00 8500.00

NEC Japan / Epygy USA / Grandstream USA

Installation, testing and commissioning of Axial Flow fan upto 450 to

600 mm. sweep in the existing opening i/c making the hole to suit

the size of the above fan making good the damage, connections,

testing commissioning etc. as required

SITC of light fixtures suitable for LED fixture, lamps with all

components and accessories including but not restricted to reflectors,

62 housings, lamp holders and including cost of ballasts and cost of

lamps complete as required and as below Make:-

Bajaj,Havells,Polycab or equivalent.

20W LED Tube light of Havells Cat Ref:

LUMILINESMART20WLED865PCWH or equivalent.

Recessed mounted 18 W Downlighter of Havells Cat Ref:Havells

VIBEFLRDDLR18WLED830S or equivalent.

Recessed mounted 12 W Downlighter of Havells Cat Ref:Havells

GLOWDLR12WLED857S or equivalent.

Surface mounted 18W LED Downlighter of Havells Cat Ref:Havells

EDGESURFACERDDLR18WLED840S or equivalent.

11/15W Mirror Light of Havells Cat Ref:

LUMILINEXS17WLED865SPCWH or equivalent.

10W LED Bulk Head of Havells Cat Ref:

RUGBYGENXFTS10WLED865SSYMBOPC or equivalent.

Supplying of Axial Flow fan upto 450 mm. Sweep,280V,1400

RPM,stainless steel material, in the existing opening i/c making the

hole to suit the size of the above fan making good the damage,

connections, testing commissioning etc. as required

Supplying of under note sizes of heavy duty exhaust fans complete

64 with fan motor, blades fixing frame, louver etc as required of havells

makes or equivalent.

450 mm exhaust fan 900 RPM Each 1 2968.00 2968.00

Supply, installation, testing and commissioning of 5 kVA,1 Phase

input and 1 Phase output UPS alongwith lead acid batteries giving a

back up of min. 30 min. at full load as per specification alongwith all

accessories including interconnecting cables, lugs, Base Frames,

Battery Rack & Battery Circuit breaker, palral kit complete as

required.Make: Schneider /Delta/APC/Autometer/ABB

IP CCTV SURVEILLANCE SYSTEM

Supply installation Testing and Commissioing Fixed Lens Outdoor

Bullet Camera - Supplying, Installation, testing & commissioning of

2MP H.265 NW IR vandal proof bullet Camera, 0.03Lux (Color), 0Lux

(B/W, IR LED on), 2.8mm fixed lens, 30fps@2M all resolutions, 120dB

WDR, H.265, H.264, MJPEG codec supported, Triple stream , Inbuilt

Analytics - Defocus detection, Directional detection, Motion detection,

Enter/Exit, Tampering, Virtual line, Audio in , alarm in & out, Micro

SD/SDHC/SDXC memory slot (Max. 128GB), IR viewable length 20m,

IP66, IK10, PoE, CE, FCC, UL, NDAA complaint, Non-Chinese.

Pelco/ Mobotix/ Avigilon/ Axis / Hanwha

Digitally signed by PRIYA

(SCHEDULE OF QUANTITIES)

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department

S.No. Description Unit Qty

DSR 2022 (In Rs.) (In Rs.)

Supply installation Testing and Commissioing Varifocal Lens Outdoor

Bullet Camera - Supplying, Installation, testing & commissioning of

2MP H.265 NW IR vandal proof bullet Camera, 0.03Lux (Color), 0Lux

(B/W, IR LED on), 3.2mm - 10mm Varifocal lens, 30fps@2M all

resolutions, 120dB WDR, H.265, H.264, MJPEG codec supported,

67 Triple stream , Inbuilt Analytics - Defocus detection, Directional Each 2 38,500 77,000

detection, Motion detection, Enter/Exit, Tampering, Virtual line, Audio

in , alarm in & out, Micro SD/SDHC/SDXC memory slot (Max. 128GB),

IR viewable length 20m, IP66, IK10, PoE, CE, FCC, UL, NDAA

complaint, Non-Chinese.

Pelco/ Mobotix/ Avigilon/ Axis / Hanwha

Supply installation Testing and Commissioing Network Video Recorder

- Supplying, Installation, testing & commissioning of 32CH NVR , Dual

monitor video out support, H.265, H.264, MJPEG compression

support, ONVIF support, 8 internal HDDs, i/c RJ45 connector i/c

connection etc, supports, N+1 failover, UL, BIS. complete as required

Pelco/ Mobotix/ Avigilon/ Axis / Hanwha

Supply installation Testing and Commissioing of Client Viewing Video

Sofware. Milestone/ Hanwha / Axis / Pelco

Supply, Installation, Testing and Commissioning of Surveillance Hard

disk - 6 TB Storage. Recording parameter: 30 days of recording at

FULL 1080p, 25fps H.264 compression, complete as required.

WD/ Seagate / Hitachi

Supply, Installation, Testing and Commissioning of Client Desktop PC

with Core i7 processor, 8GB RAM, | TB HDD, Windows 64 bit OS,

external DVD writer, wireless leyboard, wireless mouse, 2GB Graphics

card with dual monitor support, complete with high quality 5 mtrs HDMI

cables for connecting displays (2 displays per unit), complete as

required.HP / Dell / Lenovo

Supply, Installation, Testing and Commissioning of 55" or better 4K

72 professional displays for 24x7 CCTV application, complete as Each 1 1,65,000 1,65,000

required. LG / Samsung / Benq

Supply, Installation, Testing and Commissioning of Networking Rack

of 9U along with PDU (With surge protection), cable manager, fan etc

for Switches & other accessories etc, complete as required. Netrack /

Supply, Installation, Testing and Commissioning of Networking Floor

Standing Rack of 42 U along with PDU (With surge protection), cable

manager, fan etc for Switches, Servers & other accessories etc,

complete as required. Netrack / Valrack

Supply, Installation, Testing and Commissioning of Layer II Smart

Managed Gigabit Ethernet switch: 8 port RJ45 10/100/1000 T (POE), ,

complete as required.

Netgear / Cisco / Dlink/Alt global

Supply, Installation, Testing and Commissioning of Layer II Smart

Managed Gigabit Ethernet switch: 16 port RJ45 10/100/1000 T (POE),

, complete as required.

Netgear / Cisco / Dlink/Alt global

Supply, Installation, Testing and Commissioning of SFP modules

77 (1G/10G), complete as required. Each 6 4,500 27,000

Dlink/ Cisco / AMP / Molex

Supply, Installation and Commissioning of RJ-45 i/o Jack with Plate &

78 mounting Gang Box, complete as required. Each 56 1,250 70,000

Dlink/ Cisco / AMP / Molex/Legrand

The BOQ shall be read in conjunction with general notes, specification

and equipment schedule and single line diagram.

Digitally signed by PRIYA

(SCHEDULE OF QUANTITIES)

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department

S.No. Description Unit Qty

DSR 2022 (In Rs.) (In Rs.)

Supply and installation of the following cubical type panels ( Partial

Type tested ) made of 14 gauge CRCA structure, base channel, doors

& partitions complete with, Air Circuit Breaker, moulded case circuit

breakers, meters, indicating lamps, current transformer etc. Complete

in all respects, insulated bus bars with heat shrinkable PVC sleeve in

suitable bus chambers, interconnection, small wiring, name plate,

danger plate, earth bus etc. & comprising of compartments with hinged

door for each feeder & its accessories, cable alley with hinged doors,

bus chamber with bolted door etc. The panel being of dust & vermin

proof construction with rubber gasket, attractively powder coated with

Siemens grey shade and having orange peel finish. The panel shall be

free standing type/ wall mounted type as per relevant drawing,

Equipment schedule, specifications including all materials,

accessories, loose supplied items, etc. required for completeness of

the project majorly comprising of following : -

ACB shall have a rated operational voltage of 415V AC, rated

insulation voltage of 1000 volts AC, rated impulse voltage of

12kV.ACB shall be Moulded Case design and shall comply with

standards IS/IEC 60947-1 & 2. with Ics = Icu = Icw (1sec) = 50kA.

Both fixed & draw-out circuit breakers shall have single pole-pitch.

ACBs upto 3200A shall be provided with top horizontal and bottom

vertical terminal adapters on both sides for proper cable

connections/bus duct connections.

Shunt trip and closing coil (having common AC/DC supply upto 250V)

shall be continuous rated.

There Should be On, Off, Trip, Spring Charge and Ready to close

Indication lamp for all ACB on the panel door..

ACB trip unit shall be EMC/EMI tested and should have a display for

measurement of current and voltage. It shall be possible to view last 5

trip cause on trip unit. Separately powered, individual fault trip

indication LEDs (For O/L, S/C, E/F and trip unit failure) shall be

available on the trip unit which shall function even if the display fails.All

ACB shall be EMS compitable.

All MCCBS shall be with Extended type Front door operating handle,

Phase Spreaders & Phase Barriers complying to IS/IEC 60947-1 & 2.

MCCBs shall be current limiting type preferably having an

encapsulated double break design, with rated operational voltage (Ue)

of 415V, insulation voltage (Ui) of 690 V (AC 50/60 Hz) & impulse

voltage (Uimp) of not less than 8kV.

The electrical life of MCCBs shall be 8,000 operations up to 250A &

4000 operations up to 630A and shall be of single frame size upto

250A.Cable Termination on MCCB should be done using circular lugs

being fixed with a bolt passing through.

For E/F in MCCBs wherever required , external earthfault module with

CBCT should be used with indication lamp on the panel and fault

sensitivity selection from 20% – 60% In. and time delay selection in

case of Earth Fault from 0.5 to 3 Sec/ instantaneous.All incomer

MCCB should be with E/F protection also.There Should be On, Off,

Trip, and electrical fault trip Indication lamp for all MCCB on the panel

door. Separate fault differentiation indication (LED) for Over current

and Earth fault. Indication for over current and earth fault tripping shall

be extended to the panel door via indication lamps..All MCCB shall be

EMS compitable.

All MCCBs of ratigs above 250A shall be microprocessor based and

upto 250A shall be Thermal Magnetic Type and with Min 35 kA Rating

ON, OFF, Trip and Ready to close status for each ACB and ON, OFF

Trip staus for all Incommer MCCB shall be avilable on MODBUS.

Control Voltage for Closing / Tripping coils , Spring charging motor &

Indicting lamps in Manually / Electrically operated ACB Feeder shall

Digitally signed by PRIYA

(SCHEDULE OF QUANTITIES)

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department

S.No. Description Unit Qty

DSR 2022 (In Rs.) (In Rs.)

Metering CTs burden shall be with suitable VA & accuracy class .5

CTs shall be "CAST RESIN" type .

All indication lights shall be LED type.

All energy meter shall be "DIGITAL" type with Modbus Protocol as per

techncial Specification

Panel Manufacturer should have Type Test Certificates for Short Time

withstand current test of 50KA for 1.0 Sec from CPRI. Bhopal /

Control SP MCB's of 2A Rating shall be provided for each metering

20% spare control terminal to be provided.

Live parts shall not be accessible after opening the door, Transparent

acrylic sheet to be provided to cover the same & busbar joints section

shall be covered with PVC shrouds.

All bus bar shall be insulated with coloured PVC Sleeve i.e. R, Y, B,

BK as per colour code.

All internal control wiring shall be heat resistant type.

All TP/TPN feeders shall have solid isolable neutral link.

All starters shall be provided with Auto/ Manual selector switch,

MPCB/ MCCB/MCB, over load relay, single phasing preventor,

ON/OFF/ Trip/ Trip on Eclectrical Fault indication lamps, ON/OFF

push Buttons, contractor and suitable No. of Potential free contacts for

remote / local operations, indication, interlocking and Building

Management system.

Current density for bus bar shall not be more than 0.8A/Sqmm. Rating

of Bus bar is after considering all derating factors. (Bus bar sizing

calculation to be submitted for approval.)

All TP/TPN feeders shall have solid isolable neutral link.

Bus couplers shall be provided with ON & OFF indicating lights but

without releases.

All feeders shall be provided with door interlocked with door defeat,

pad lock facility.

Spare contacts of Relays/Contactor etc. shall be wired upto terminal

Degree of protection for following type of distribution panel enclosure

shall be as per IS:13947-1993.

IP 43 for indoor panels.

IP 55 for outdoor panels.

Contractor and panel builder shall have to submit the GA drawing and

get approval from consultant before inplementing.

Rotary handal shall be provided with all MCCBs.

2 Nos.500A, 4P MCCB

2 Nos.500A, 4P Contactor

Metering & Indication:

Combined Ammeter/Voltmeter with Selector Switch and 400/5A, CL-1,

10VA CTs and 2A control MCB.

Sets of phase indicating lamp with control MCBs.

All incomer shall be electrical and mechanical interlock.Consider

suitable rating of contactor and software, hardware , accessories for

interlocking and auto on auto off of incomers.

600A, TPN aluminium, colour coded bus bars suitable for 415V, 50Hz

with fully rated neutral.(After deration)

1 Nos.160A, TPN MCCB

2 Nos.100A, TPN MCCB

Digitally signed by PRIYA

(SCHEDULE OF QUANTITIES)

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department

S.No. Description Unit Qty

DSR 2022 (In Rs.) (In Rs.)

14 Nos.63A, TPN MCCB

4 Nos.40A, TPN MCCB

1 Nos.40A, TPN MCB

4 Nos.16A, DP MCB

2 Nos. Bulb with holder

Panel shall be suitable for incoming & outgoing supply with cables,and

top / bottom entry as required.

Supply & Laying of 1.1KV grade multicore aluminium conductor XLPE

insulated and PVC sheathed armoured cable conforming to IS : 7098

(Part-I) 1998 along walls/ on existing cable trays etc. in an approved

manner and as per follows;

Constructing Masonry chamber 60x60x75 cm (deep) inside with 75

class designation FPS brick work in cement mortar 1:4 (1 cement: 4

coarse sand) (for cable entry) with 10 mm thick M.S. hinged cover

81 plate on top in 40 x 5 mm MS angle iron frame embedded in C C 1:2:4 each 8 7500.00 60000.00

i/c necessary excavation and inside plastering with cement mortar 1:3

(1 cement:3 fine sand) finished with a floating coat of neat cement

complete as required and as per specifications attached.

Constructing masonry chamber 60 cm x 45 cm x 50 cm (deep) inside

with 75 class designation FPS brick work in cement mortar 1:4 (1

cement : 3 coarse sand) (for cable entry) with 10 mm thick M.S.

hinged cover plate on top in 40 x 40 x 5 mm MS angle iron frame

embedded in C C 1:2: 4i/c necessary excavation and inside plastering

with cement mortar 1:3 (1 cement:3 fine sand) finished with a floating

coat of neat cement complete as required and as per specifications

EXTERNAL LIGHTING

Supplying and fixing (with suitable MS clamp) 300mm long 65mm dia

MS pipe with base plate i/c nipple for Gate light.

Supplying, installing, testing & commissioning of 4.5 Mtr long

single dip Galvanised steel octagonal poles in 3mm sheet

integrated connector box inside the pole containing one no. 5A

MCB , Neutral link and earth terminal with single over hang

bracket 1m long ; providing and fixing in position 1:2:4

reinforced cement concrete foundation for the pole, size

500mm(L)X500mm(W)X 1650mm deep i/c excavation of earth,

providing, cutting, bending and placing in position reinforcement as

per drawing and providing PVC flexible pipes 50mm dia for cable

entry and exit as required i/c foundation bolts, transportation,

handling, marking etc. as per specification and drawings as required of

Havells/ Bajaj or equivalent

Supply and installation of following arms suitable for 4.5 Mtr to 9 mtr

street light pole

a Single Arm over hang bracket 1mtr length each 14 3384.00 47376.00

b Double Arm over hang bracket 1mtr length each 3 4600.00 13800.00

Digitally signed by PRIYA

(SCHEDULE OF QUANTITIES)

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department

S.No. Description Unit Qty

DSR 2022 (In Rs.) (In Rs.)

Providing and erection of black painted galvanized 3 meter high poles

in different section, top 60mm dia., bottom 100mm dia. with gold colour

painted ornamental cast aluminium ring having lockable weather proof

flush door junction box in bottom section, and suitable arrangement for

installation of CCTV and with base plate dia. 290mm having 4 holes of

22mm dia. complete erected in an approved manner including

foundation of Suitable size & type of foundation bolts as required. (For

supply & drawing 3 core 2.5 sqmm unarmoured copper

cable inside the GI Octagonal pole from connector box to the

fixture including connections with thimbles as required upto 9m high

Supplying and fixing (with suitable MS clamp) 1200mm long vertically

88 and 900mm inclined at 45 degree, 65mm dia MS pipe with hardware each 1 5000.00 5000.00

i/c nipple for street light.(boundary wall light)

Supplying and fixing of LED Bollard Fitting 600mm High with IP65 and

IK07 Housing made up of aluminum pipe powder coated black after

phosphochromate treatment with aluminum heat sink for effective

thermal management Complete with Mounting Brackets & accessories

as required with connections similar. Havells Mount Bollard 0.60 mtr

89 5700K MOUNTBLMINIMOUNTBL10WLED830PSYMTOPMMAS . The Set 18 5771.00 103878.00

product should be BIS approved with R number mentioned on product

label. To be supported with Product test reports - LM79, Is 10322/IEC

60598 and for LEDs - LM80, RoHS and Photo Biological Safety

Supply, fixing &testing of prewired external light fixture having Die-

cast housing with epoxy coating and having profiled cooling fins at

the top for effective heat dissipation, separate driver and LED

lamp cavity, heat resistant toughened clear glass cover with high

transmittance and high quality gasketing system, high power

LED complete as required.

25 Watt LED Fitting Lighting lantern on GATE/ POST TOP of Havells

Cat no.CORALMINIPT15WLED757PSYMTOPC or equivalent ..

Street Light Luminare of 60 watt LED including suitable fixing MS

iii clamps etc.as requird of Havells Cat No. each 20 6224.00 124480.00

ENDURASUNDOWNSL60WLED765PASYBOTG or equivalent

Street Light Luminare of 35 watt LED including suitable fixing MS

iv clamps etc.as requird of Havells Cat No. each 1 3847.00 3847.00

ENDURASUNDOWNSL35WLED765PASYBOPC or equivalent

Floodlight LED luminaire 50 Watas with high pressure die cast

v housing with IP66 deg of protection of Havells Cat No. each 2 5429.00 10858.00

JETAQUANTOPLUSFLP50WLED757SYMLENS or equivalent

DSR TOTAL Rs. 96,67,507.23

NON DSR TOTAL Rs. 63,38,144.00

DSR + NON DSR TOTAL Rs. 1,60,05,651.23

Digitally signed by PRIYA

ABSTRACT OF COST

Name of the work : Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General

Store Area of MM- Stores Department (SHED-1 )

Sub Work : Construction of Administrative Building

DSR Item N DSR Item

S.H. No. Description of Sub-Head Amount Amount

2 Concrete Work : ₹ 5,53,787.40

3 Reinforced Cement Concrete : ₹ 51,27,135.95

4 Masonry Work : ₹ 10,09,321.80

5 Cladding Work : ₹ 3,32,206.67

6 Wood and P.V.C. Work : ₹ 3,91,935.35

7 Steel Work : ₹ 47,681.87

11 Aluminium Work : ₹ 2,21,357.84

12 Water proofing Work : ₹ 5,16,570.39

13 Sanitary Fixtures & CP Brass Fittings : ₹ 61,246.10 ₹ 21,744.00

14 Soil, Waste, Vent & Rain Water Pipes : - ₹ 1,85,033.91

15 Water Supply System (Internal) : ₹ 81,342.31 ₹ 16,640.00

16 External Sewerage & Storm Water Drainage : ₹ 1,62,346.30 -

17 External Water Supply : ₹ 10,510.85 -

18 Fire Fighting Work : ₹ 2,70,312.83 ₹ 54,660.00

Total (DSR +NDSR) : ₹ 1,73,80,397.28

Digitally signed by PRIYA

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM-

Stores Department (SHED-1 )

Sub Work : Construction of Administrative Building

Sl. No DSR 2023 Description of Item Quantity Unit Rate (Rs)

Sub-Head : Earth Work

2.6 Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means over areas

(exceeding 30cm in depth , 1.5m in width as well as 10

sqm on plan) including getting out and disposal of

excavated earth , lead up to 50m and for all lift , as

directed by Engineer-in-Charge.

2.7 Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means over areas

(exceeding 30 cm in depth, 1.5m in width as well as 10

sqm on plan) including getting out and disposal of

excavated earth, lead up to 50 m and lift up to 1.5m, as

directed by Engineer-in-Charge.

2.25 Filling available excavated earth (excluding rock) in

trenches, plinth, sides of foundations etc. in layers not

5 exceeding 20cm in depth, consolidating each deposited 200.00 Cum 209.78 41955.76

layer by ramming and watering, lead up to 50 m and lift

2.25A Excavating, supplying and filling of local earth (including

royalty) by mechanical transport up to a lead of 5 km,

6 also including ramming and watering of the earth in 80.00 Cum 749.75 59979.61

layers not exceeding 20 cm in trenches, plinth, sides of

foundation etc., complete.

2.26 Extra for every additional lift of 1.5 m or part thereof in

7 excavation /banking excavated or stacked materials.

9 2.26.2 Ordinary or hard rock. 5.00 Cum 243.39 1216.93

2.27 Supplying and filling in plinth with sand under floors,

10 including watering, ramming, consolidating and dressing 45.00 Cum 2273.05 102287.23

2.34 Supplying chemical emulsion in sealed containers

including delivery as specified.

2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

2.35 Diluting and injecting chemical emulsion for PRE

13 CONSTRUCTIONAL anti- termite treatment (excluding

the cost of chemical emulsion) :

2.35.3 Treatment of soil under existing floors using chemical

emulsion @ one litre per hole, 300 mm apart including

14 drilling 12 mm diameter holes and plugging with cement

mortar 1 :2 (1 cement : 2 Coarse sand) to match the

existing floor :

2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1%

16 Total of the Sub-Head - Earth Work : ₹ 3,94,383.61

17 Sub-Head : Concrete Work

Digitally signed by PRIYA

Sl. No DSR 2023 Description of Item Quantity Unit Rate (Rs)

4.1 Providing and laying in position cement concrete of

18 specified grade excluding the cost of centering and

shuttering - All work up to plinth level :

4.1.6 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from

19 natural sources : 6 graded stone aggregate 40 mm 12.00 Cum 7683.416 92200.99

nominal size derived from natural sources)

4.11 Providing and laying damp-proof course 50mm thick

with cement concrete 1:2:4 (1 cement : 2 coarse sand

20 (zone-III) derived from natural sources : 4 graded stone 45.00 Sqm 530.6012 23877.06

aggregate 20mm nominal size derived from natural

4.12 Extra for providing and mixing water proofing material

21 in cement concrete work in doses by weight of cement 15.00 units 19.42595 291.39

as per manufacturer’s specification.

4.13 Providing and applying a coat of residual petroleum

bitumen of grade of VG-10 of approved quality using 1.7

22 kg per square metre on damp proof course after 45.00 Sqm 156.4243 7039.10

cleaning the surface with brushes and finally with a

piece of cloth lightly soaked in kerosene oil.

4.17 Making plinth protection 50mm thick of cement

concrete 1:3:6 (1 cement : 3 coarse sand (zone-III)

derived from natural sources : 6 graded stone aggregate

20 mm nominal size derived from natural sources) over

23 75mm thick bed of dry brick ballast 40 mm nominal size, 65.00 Sqm 801.9758 52128.43

well rammed and consolidated and grouted with fine

sand, including necessary excavation leveling & dressing

& finishing the top smooth.

4.20 Providing and laying in position ready mixed or site

batched design mix cement concrete for plain cement

concrete work; using coarse aggregate and fine

aggregate derived from natural sources, Portland

Pozzolana/Ordinary Portland/Portland Slag cement,

admixtures in recommended proportions as per IS : 9103

24 to accelerate/ retard setting of concrete, to improve

durability and workability without impairing strength;

including pumping of concrete to site of laying, curing,

carriage for all leads; but excluding the cost of centering,

shuttering and finishing as per direction of the Engineer-

in-charge; for the following grades of concrete.

Note : Extra cement upto 10% of the minimum specified

cement content in design mix shall be payable

separately. In case the cement content in design mix is

25 more than 110% of the minimum specified cement

content, the contractor shall have discretion to either re-

design the mix or bear the cost of extra cement.

26 4.20.1 All works up to plinth level:

4.20.1.1 Concrete of M-10 grade with minimum cement content

28 Total of the Sub-Head - Concrete Work : ₹ 5,53,787.40

Digitally signed by PRIYA

Sl. No DSR 2023 Description of Item Quantity Unit Rate (Rs)

29 Sub-Head : Reinforced Cement Concrete

5.3 Reinforced cement concrete work in beams, suspended

floors, roofs having slope up to 15° landings, balconies,

shelves, chajjas, lintels, bands, plain window sills,

staircases and spiral stair cases above plinth level up to

floor five level, excluding the cost of centering,

shuttering, finishing and reinforcement with 1:1.5:3 (1

cement : 1.5 coarse sand(zone-III)derived from natural

sources : 3 graded stone aggregate 20 mm nominal size

derived from natural sources).

5.9 Centering and shuttering including strutting, propping

etc. and removal of form for :

5.9.1 Foundations, footings, bases of columns, etc. for mass

33 5.9.4 Shelves (Cast in situ) 5.00 Sqm 992.44 4962.18

34 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts 205.00 Sqm 1028.88 210920.27

5.9.20 Suspended floors, roofs, landings, balconies and access

platform with water proof ply 12 mm thick

5.9.21 Lintels, beams, plinth beams, girders, bressumers and

cantilevers with water proof ply 12 mm thick

5.11 Extra for additional height in centering, shuttering where

ever required with adequate bracing, propping etc.,

including cost of de-shuttering and decentering at all

levels, over a height of 3.5 m, for every additional height

of 1 metre or part thereof (Plan area to be measured).

5.11.1 Suspended floors, roofs, landing, beams and balconies

(Plan area to be measured)

5.22 Steel reinforcement for R.C.C. work including

39 straightening, cutting, bending, placing in position and

binding all complete upto plinth level.

5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or

5.22A Steel reinforcement for R.C.C. work including

41 straightening, cutting, bending, placing in position and

binding all complete above plinth level.

5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or

5.30 Add for plaster drip course/ groove in plastered surface

or moulding to R.C.C. projections

Digitally signed by PRIYA

Sl. No DSR 2023 Description of Item Quantity Unit Rate (Rs)

5.33 Providing and laying in position ready mixed or site

batched design mix cement concrete for reinforced

cement concrete work; using coarse aggregate and fine

aggregate derived from natural sources, Portland

Pozzolana/ Ordinary Portland/ Portland Slag cement,

admixtures in recommended proportions as per IS: 9103

44 to accelerate/ retard setting of concrete, to improve

durability and workability without impairing strength;

including pumping of concrete to site of laying, curing,

carriage for all leads; but excluding the cost of centering,

shuttering, finishing and reinforcement as per direction

of the engineer-in-charge; for the following grades of

Note: Extra cement up to 10% of the minimum specified

cement content in design mix shall be payable

separately. In case the cement content in design mix is

45 more than 110% of the specified minimum cement

content, the contractor shall have discretion to either re-

design the mix or bear the cost of extra cement

46 5.33.1 All works upto plinth level

5.33.1.1 Concrete of M25 grade with minimum cement content

5.33.1.2 Concrete of M30 grade with minimum cement content

49 5.33.2 All works above plinth level upto floor V level

5.33.2.1 Concrete of M25 grade with minimum cement content

5.33.2.2 Concrete of M30 grade with minimum cement content

5.35 Add for using extra cement in the items of design mix

over and above the specified cement content therein.

53 Total of the Sub-Head - Reinforced Cement Concrete : ₹ 51,27,135.95

54 Sub-Head : Masonry Work

6.1 Brick work with common burnt clay F.P.S. (non modular)

55 bricks of class designation 7.5 in foundation and plinth

56 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 1.00 Cum 7633.647 7633.65

6.4 Brick work with common burnt clay F.P.S. (non modular)

bricks of class designation 7.5 in superstructure above

plinth level up to floor V level in all shapes and sizes in :

58 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 65.00 Cum 9746.098 633496.39

6.13 Half brick masonry with common burnt clay F.P.S. (non

59 modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V level.

60 6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) 280.00 Sqm 1202.803 336784.88

6.15 Extra for providing and placing in position 2 Nos 6mm

61 dia. M.S. bars at every third course of half brick 280.00 Sqm 112.1674 31406.88

masonry.ird course of half brick masonry.

62 Total of the Sub-Head - Masonry Work : ₹ 10,09,321.80

63 Sub-Head : Cladding Work

Digitally signed by PRIYA

Sl. No DSR 2023 Description of Item Quantity Unit Rate (Rs)

8.2 Providing and fixing 18 mm thick gang saw cut, mirror

polished, premoulded and prepolished, machine cut for

kitchen platforms, vanity counters, window sills, jambs,

facias and similar locations of required size, approved

shade, colour and texture laid over 20 mm thick base

cement mortar 1:4 (1 cement : 4 coarse sand), joints

treated with white cement, mixed with matching

pigment, epoxy touch ups, including rubbing, curing,

moulding and polishing to edges to give high gloss finish

etc. complete at all levels.

65 8.2.2 Granite stone slab colour black, Cherry/Ruby red

8.2.3 Granite stone slab all colour and texture except black,

Cherry/ Ruby red

8.4 Extra for fixing marble /granite stone, over and above

corresponding basic item, in facia and drops of width

upto 150 mm with epoxy resin based adhesive, including

cleaning etc. complete.

8.5 Extra for providing opening of required size & shape for

wash basin/kitchen sink in kitchen platform, vanity

counter and similar location in marble/ Granite/ stone

work, including necessary holes for pillar taps etc.

including moulding, rubbing and polishing of cut edges

8.31 Providing and fixing Ist quality ceramic glazed wall tiles

conforming to IS: 15622 (thickness to be specified by the

manufacturer), of approved make, in all colours, shades

except burgundy, bottle green, black of any size as

approved by Engineer-in-Charge, in skirting, risers of

steps and dados, over 12 mm thick bed of cement

mortar 1:3 (1 cement : 3 coarse sand) and jointing with

grey cement slurry @ 3.3kg per sqm, including pointing

in white cement mixed with pigment of matching shade

74 Total of the Sub-Head - Cladding Work : ₹ 3,32,206.67

75 Sub-Head : Wood and P.V.C. Work

9.1 Providing wood work in frames of doors, windows,

clerestory windows and other frames, wrought framed

76 and fixed in position with hold fast lugs or with dash

fasteners of required dia & length (hold fast lugs or dash

fastener shall be paid for separately).

9.7 Providing and fixing panelling or panelling and glazing in

panelled or panelled and glazed shutters for doors,

windows and clerestory windows (Area of opening for

panel inserts excluding portion inside grooves or rebates

to be measured). Panelling for panelled or panelled and

glazed shutters 25 mm to 40 mm thick :

79 9.7.7 Float glass panes

Digitally signed by PRIYA

Sl. No DSR 2023 Description of Item Quantity Unit Rate (Rs)

9.7.7.2 5.5 mm thick glass panes (weight not less than 12.50

9.21 Providing and fixing ISI marked flush door shutters

conforming to IS : 2202 (Part I) non-decorative type,

core of block board construction with frame of 1st class

hard wood and well matched commercial 3 ply

veneering with vertical grains or cross bands and face

veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt

hinges with necessary screws

9.23 Extra for providing lipping with 2nd class teak wood

battens 25 mm minimum depth on all edges of flush

door shutters (over all area of door shutter to be

9.24 Extra for providing vision panel not exceeding 0.1 sqm in

84 all type of flush doors (cost of glass excluded) (overall

area of door shutter to be measured) :

85 9.24.1 Rectangular or square. 30.00 Sqm 213.15 6394.51

9.40 Providing and fixing wooden moulded beading to door

86 and window frames with iron screws, plugs and priming

coat on unexposed surface etc. complete :

87 9.40.1 2nd class teak wood

9.74 Providing and fixing bright finished brass tower bolts

(barrel type) with necessary screws etc. complete :

9.75 Providing and fixing bright finished brass door latch with

necessary screws etc. complete :

9.76 Providing and fixing bright finished brass 100 mm

mortice latch and lock with 6 levers and a pair of lever

handles of approved quality with necessary screws etc.

9.82 Providing and fixing bright finished brass hanging type

95 floor door stopper with necessary screws, etc. complete. 15.00 No. 130.20 1953.03

9.127 Providing & Fixing decorative high pressure laminated

sheet of plain / wood grain in gloss / matt / suede finish

with high density protective surface layer and reverse

side of adhesive bonding quality conforming to IS : 2046

Type S, including cost of adhesive of approved quality.

98 Total of the Sub-Head - Wood And P.V.C Work : ₹ 3,91,935.35

99 Sub-Head : Steel Work

10.25 Steel work welded in built up sections/ framed work,

including cutting, hoisting, fixing in position and applying

a priming coat of approved steel primer using structural

steel etc. as required.

10.25.2 In gratings, frames, guard bar, ladder, railings, brackets,

gates and similar works.

Digitally signed by PRIYA

Sl. No DSR 2023 Description of Item Quantity Unit Rate (Rs)

10.27 Providing and fixing carbon steel galvanised (minimum

coating 5 micron) dash fastener of 10 mm dia double

threaded 6.8 grade (yield strength 480 N/mm2), counter

102 sunk head, comprising of 10 mm dia polyamide PA 6

grade sleeve, including drilling of hole in frame ,

concrete/ masonry, etc. as per direction of Engineer-in-

104 Total of the Sub-Head - Steel Work : ₹ 47,681.87

105 Sub-Head : Flooring

11.24 Extra for pre finished nosing to treads of steps of

marble/ granite stone.

11.25 Extra for marble/ granite stone flooring in treads of

steps and risers using single length up to 2.00 metre .

11.26 Kota stone slab flooring over 20 mm (average) thick base

laid over and jointed with grey cement slurry mixed with

108 pigment to match the shade of the slab including

rubbing and polishing complete with base of cement

mortar 1 : 4 (1 cement : 4 coarse sand) :

11.27 Kota stone slabs 20 mm thick in risers of steps, skirting,

dado and pillars laid on 12 mm (average) thick cement

mortar 1:3 (1 cement 3 coarse sand) and jointed with

grey cement slurry mixed with pigment to match the

shade of the slabs, including rubbing and polishing

11.41A Providing and laying Vitrified tiles in floor in different

sizes (thickness to be specified by the manufacturer)

with water absorption less than 0.08% and conforming

to IS:15622, of approved brand & manufacturer, in all

colours and shade, laid on 20 mm thick cement mortar

1:4 (1 cement: 4 coarse sand) jointing with grey cement

111 slurry @3.3 kg/sqm including grouting the joints with

white cement and matching pigments etc. The tiles must

be cut with the zero chipping diamond cutter only .

Laying of tiles will be done with the notch trowel, plier,

wedge, clips of required thickness, leveling system and

rubber mallet for placing the tiles gently and easily.

112 11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size

11.46 Providing and laying Vitrified tiles in different sizes

(thickness to be specified by manufacturer) with water

absorption less than 0.08 % and conforming to I.S.

15622, of approved make in all colours & shade in

114 skirting, riser of steps, over 12 mm thick bed of cement

mortar 1:3 (1cement: 3 coarse sand), jointing with grey

cement slurry @ 3.3kg/sqm including grouting the joint

with white cement & matching pigments etc. complete.

Digitally signed by PRIYA

Sl. No DSR 2023 Description of Item Quantity Unit Rate (Rs)

11.56 Providing and laying Polished Granite stone flooring in

required design and patterns, in linear as well as

curvilinear portions of the building all complete as per

the architectural drawings with 18 mm thick stone slab

over 20 mm (average) thick base of cement mortar 1:4

117 (1 cement : 4 coarse sand) laid and jointed with cement

slurry and pointing with white cement slurry admixed

with pigment of matching shade including rubbing ,

curing and polishing etc. all complete as specified and as

directed by the Engineer-in-Charge.

11.56.1 Polished Granite stone slab jet Black, Cherry Red, Elite

Brown, Cat Eye or equivalent

11.56.2 Polished Granite stone slab of all colour and texture

except Black, Cherry/Ruby Red

16.91 Providing and laying factory made chamfered edge

Cement Concrete paver blocks In foot path, park &

lawns driveway or light & traffic parking etc. of required

strength, thickness & size/ shape, made by table

vibratory method using PU mould, laid in required

colour & pattern over 50mm thick compacted bed of

course sand, compacting and proper embedding/ laying

of inter locking paver blocks into the sand bedding layer

through vibratory compaction by using plate vibrator,

filling the joints with sand and cutting of paver blocks as

per required size and pattern, finishing and sweeping

extra sand, all complete as per manufacturer's

specifications & direction of Engineer in-Charge.

16.91.1 60mm thick Cement concrete paver block of M-35 grade

with approved colour, design & pattern

122 Total of the Sub-Head - Flooring : ₹ 5,42,879.92

123 Sub-Head : Roofing

12.21 Providing gola 75x75 mm in cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 stone aggregate 10 mm and

124 down gauge), including finishing with cement mortar 1:3

(1 cement : 3 fine sand) as per standard design :

12.22 Making khurras 45x45 cm with average minimum

thickness of5 cm cement concrete 1:2:4 (1 cement : 2

coarse sand : 4 graded stone aggregate of 20 mm

126 nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, 5.00 No. 285.34 1426.71

finished with 12 mm cement plaster 1:3 (1 cement : 3

coarse sand) and a coat of neat cement, rounding the

edges and making and finishing the outlet complete.

127 Total of the Sub-Head - Roofing : ₹ 23,706.07

128 Sub-Head : Finishing

129 13.1 12 mm cement plaster of mix :

13.2 15 mm cement plaster on the rough side of single or half

brick wall of mix :

Digitally signed by PRIYA

Sl. No DSR 2023 Description of Item Quantity Unit Rate (Rs)

13.11 18 mm cement plaster in two coats under layer 12 mm

thick cement plaster 1:5 (1 cement: 5 coarse sand)

finished with a top layer 6mm thick cement plaster 1:6

(1 cement: 6 fine sand).

134 13.16 6 mm cement plaster of mix :

13.26 Providing and applying plaster of paris putty of 2 mm

136 thickness over plastered surface to prepare the surface 1160.00 Sqm 281.17 326154.66

even and smooth complete.

13.45 Finishing walls with textured exterior paint of required

13.45.1 New work (Two or more coats applied @ 3.28 ltr/10

138 sqm) over and including priming coat of exterior primer 310.00 Sqm 239.32 74188.91

applied @2.20kg/10 sqm.

13.61 Painting with synthetic enamel paint of approved brand

and manufacture to give an even shade :

140 13.61.1 Two or more coats on new work. 10.00 Sqm 166.86 1668.60

13.83 Wall painting with premium acrylic emulsion paint of

interior grade, having VOC (Volatile Organic Compound )

content less than 50 grams/ litre. of approved brand and

manufacture, including applying additional coats

wherever required to achieve even shade and colour.

13.116 Polishing in high gloss/matt finish melamine clear polish

on wood work in required color/wooden shade texture

with following process in the sequence as detailed

1. The surface to be polished is rubbed with sand paper

144 80/120 no. and then with sand paper of 160/180 nos.

2. Applying two coats of sealer with spray gun and

145 allowing sufficient drying time for 1st coat and 2nd coat

is allowed to dry for 8 to 12 hrs.

3. On drying of sealer coat, wet rubbing with emery

cloth of finer grading with water to remove excess sealer

layer and make the surface further smooth after this wet

rubbing, then surface is applied with special grade

melamine fillers to fill all the small and big

holes/grooves etc. Filler coat to be allowed to dry for 4

to 6 hrs on which again a light wet rubbing is done this

surface is further allowed to dry for 12 hrs.

Digitally signed by PRIYA

Sl. No DSR 2023 Description of Item Quantity Unit Rate (Rs)

4. On this, 1st coat of melamine polish is applied with

spray gun using melamine clear polish and melamine

thinner in required proportion. This 1st coat is allowed

to dry for 24 hrs then this dry surface is again fine wet

rubbed smooth, which is further allowed to dry for 12

147 hrs. The final melamine polish is applied with

compressor pressure spray gun using melamine clear

polish and melamine thinner mixed in required

proportion complete as per direction of Engineer-in-

Charge. (Finalo coat to be done in 1 or 2 layers without

148 Total of the Sub-Head - Finishing : ₹ 12,18,305.10

149 Sub-Head : Aluminium Work

21.1 Providing and fixing aluminium work for doors,

windows, ventilators and partitions with extruded built

up standard tubular sections/appropriate Z sections and

other sections of approved make conforming to IS: 733

and IS: 1285, fixing with dash fasteners of required dia

and size, including necessary filling up the gaps at

junctions, i.e. at top, bottom and sides with required

EPDM rubber/ neoprene gasket etc. Aluminium sections

shall be smooth, rust free, straight, mitred and jointed

mechanically wherever required including cleat angle,

Aluminium snap beading for glazing / paneling, C.P.

brass/ stainless steel screws, all complete as per

architectural drawings and the directions of Engineer-in-

charge. (Glazing, paneling and dash fasteners to be paid

for separately) :

151 21.1.1 For fixed portion

21.1.1.2 Powder coated aluminium (minimum thickness of

powder coating 50 micron)

21.1.2 For shutters of doors, windows & ventilators including

providing and fixing hinges/ pivots and making provision

153 for fixing of fittings wherever required including the cost

of EPDM rubber / neoprene gasket required (Fittings

shall be paid for separately).

21.1.2.2 Powder coated aluminium (minimum thickness of

powder coating 50 micron)

21.3 Providing and fixing glazing in aluminium door, window,

ventilator shutters and partitions etc. with EPDM rubber

/ neoprene gasket etc. complete as per the architectural

drawings and the directions of engineer-in-charge . (Cost

of aluminium snap beading shall be paid in basic item):

21.3.3 With float glass panes of 8 mm thickness (weight not

less than 20 kg/sqm)

21.11 Providing and fixing stainless steel (SS 304 grade)

adjustable friction windows stays of approved quality

157 with necessary stainless steel screws etc. to the side

hung windows as per direction of Engineer-in-charge

Digitally signed by PRIYA

Sl. No DSR 2023 Description of Item Quantity Unit Rate (Rs)

21.15 Providing and fixing aluminium casement windows

159 fastener of required length for aluminium windows with

necessary screws etc. complete.

21.15.2 Powder coated minimum thickness 50 micron

161 Total of the Sub-Head - Aluminium Work : ₹ 2,21,357.84

162 Sub-Head : Water Proofing

22.3 Providing and laying water proofing treatment to

163 vertical and horizontal surfaces of depressed portions of

W.C., kitchen and the like consisting of:

(i) Ist course of applying cement slurry @ 4.4 kg/sqm

mixed with water proofing compound conforming to IS

164 2645 in recommended proportions including rounding

off junction of vertical and horizontal surface.

(ii) IInd course of 20 mm cement plaster 1:3 (1 cement :

3 coarse sand) mixed with water proofing compound in

recommended proportion including rounding off

junction of vertical and horizontal surface.

(iii) IIIrd course of applying blown or residual bitumen

applied hot at 1.7 kg. per sqm of area.

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps 25.00 Sqm 716.08 17902.11

at joints of PVC sheet should be 100 mm wide and

pasted to each other with bitumen @ 1.7 kg/sqm).

22.7 Providing and laying integral cement based water

proofing treatment including preparation of surface as

required for treatment of roofs, balconies, terraces etc

consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75

kg/sqm of cement admixed with water proofing

compound conforming to IS. 2645 and approved by

Engineer-in-charge over the RCC slab including adjoining

walls upto 300 mm height including cleaning the surface

before treatment.

(b) Laying brick bats with mortar using broken

bricks/brick bats 25 mm to 115 mm size with 50% of

cement mortar 1:5 (1 cement : 5 coarse sand) admixed

with water proofing compound conforming to IS : 2645

and approved by Engineer-in-charge over 20 mm thick

170 layer of cement mortar of mix 1:5 (1 cement :5 coarse

sand ) admixed with water proofing compound

conforming to IS : 2645 and approved by Engineer-in-

charge to required slope and treating similarly the

adjoining walls upto 300 mm height including rounding

of junctions of walls and slabs.

(c) After two days of proper curing applying a second

coat of cement slurry using 2.75 kg/ sqm of cement

admixed with water proofing compound conforming to

IS : 2645 and approved by Engineerin- charge.

Digitally signed by PRIYA

Sl. No DSR 2023 Description of Item Quantity Unit Rate (Rs)

(d) Finishing the surface with 20 mm thick jointless

cement mortar of mix 1:4 (1 cement :4 coarse sand)

admixed with water proofing compound conforming to

IS : 2645 and approved by Engineerin- charge including

laying glass fibre cloth of approved quality in top layer of

plaster and finally finishing the surface with trowel with

neat cement slurry and making pattern of 300x300 mm

square 3 mm deep.

(e) The whole terrace so finished shall be flooded with

water for a minimum period of two weeks for curing and

173 for final test.“All above operations to be done in order

and as directed and specified by the Engineer-in-Charge :

22.7.1 With average thickness of 120 mm and minimum 310.00 Sqm 1608.61 498668.29

thickness at khurra as 65 mm.

Total of the Sub-Head - Water Proofing : ₹ 5,16,570.39

Digitally signed by PRIYA

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department (SHED-1 )

Construction of Administrative Building, PLUMBING WORKS DETAILED ESTIMATE

S.I DSR MR MR DSR

Description of Item Unit

No Item No Item No Admin Block Rate Amount Rate Amount

SUBHEAD-I(Sanitary Fixtures & CP Brass Fittings)

1 17.3 Providing and fixing white vitreous china pedestal type water closet (European

type) with seat and lid, 10 litre low level white vitreous china flushing cistern &

C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow

arrangement with specials of standard make and mosquito proof coupling of

approved municipal design complete, including painting of fittings and brackets,

cutting and making good the walls and floors wherever required :

1.1 17.3.2 W.C. pan with ISI marked black solid plastic seat and lid Each 3 6515.55 19546.65

2 17.7 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,

32 mm C.P. brass waste of standard pattern, including painting of fittings and

brackets, cutting and making good the walls wherever require:

2.1 17.7.2 White Vitreous China Wash basin size 630x450 mm with a Each 3 3960.55 11881.65

single 15 mm C.P. brass pillar tap

3 17.22A Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make Each 3 1034.8 3104.4

and as per the direction of Engineer-in-charge.

4 17.10 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983

with C.I. brackets and stainless steel plug 40 mm, including painting of fittings

and brackets, cutting and making good the walls wherever required:

4.1 17.10.1 Kitchen sink with drain board

5 MR 5 Fixing of 15 mm C.P brass wall mounted mixing fittings swinging spout for sink Each

complete including cutting and making good the walls where required. (Pantry, 1 5388.00 5388

Kitchen, Coffee-Break etc.)

6 17.4 Providing and fixing white vitreous china flat back or wall corner type lipped front

urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with

automatic flushing cistern with standard flush pipe and C.P. brass spreaders with

brass unions and G.I clamps complete, including painting of fittings and brackets,

cutting and making good the walls and floors wherever required :

6.1 17.4.1 One urinal basin with 5 litre white P.V.C. automatic flushing cistern Each 1 6258.75 6258.75

7 MR 7 Providing and fixing in postion storage type automatic electric water heater

pressure type thermostatically controlled, single phase wall mounted of

approved make (to the approval of Engineer-in-charge) with thermostats, inner

container of stainless steel, Inner glass lining with B-Rating minimum 3 stars

complete with 1 Mtr. three core flexible cord with plug, non return valve and

pressure release valve complete including fixing and testing complete in all

7.1 MR 7.1 15 litre capacity water heater Each 1 13470.00 13470

8 MR 8 Providing & fixing in position Water Cooler without Stablizer of approved make

(to the approval of Engineer-in-charge ) including carriage complete in all respect.

8.1 MR 8.1 Each RO

Water Cooler Full Steel Body 40 ltr Capacity without Stablizer

9 17.16A Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long Each 3 349.15 1047.45

with S.S. triangular plate to Eureopean type W.C. of quality and make as

approved by Engineer - in - charge.

10 18.53 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of Each 11 574.3 6317.3

approved quality conforming to IS:8931

11 17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including

11.1 17.28.2 Flexible pipe

12 MR 12 Providing & Fixing in position C.P. Brass coat hook of approved make (to the

approval of Engineer-in-charge ) fixed into wall with C.P. brass screws and rawl

plugs etc. complete in all respect.

12.1 MR 12.1 C.P.Brass coat hook Each 3 962.00 2886

Digitally signed by PRIYA

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department (SHED-1 )

Construction of Administrative Building, PLUMBING WORKS DETAILED ESTIMATE

13 17.31 Providing and fixing 600x900 mm beveled edge mirror of superior glass (of Each 3 1607.95 4823.85

approved quality) complete with 6 mm thick hard board ground fixed to wooden

cleats with C.P. brass screws and washers complete.

14 17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm Each 3 231.95 695.85

wide with minimum distances of 37 mm from wall face with concealed fittings

arrangement of approved quality and colour, weighing not less than 88 gms.

15 17.71 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and Each 3 168.35 505.05

112 mm distance from wall of standard shape with bracket of the same materials

with snap fittings of approved quality and colour, weighing not less than 105

SUBHEAD II(Soil, Waste, Vent & Rain Water Pipes)

16 MR 1 Supply, installation , testing commissioning of PP Mineral filled low noise Soil &

Waste system as per EN 12056, with density 1.9 g/cm3. PP mineral(Astolan) filled

Low noise system should has a fire classification DIN 4102-B2/EN13501 . Product

should have a chemical resistance of pH 2-12 and is a complete sound protection

system according to DIN 4109. including with push fit rubber ring sockets all

necessary fittings and specials such as Bends, junctions, offsets & vent cowl. Fixing

at wall/ceiling level supported by rubber line bracket & hangers etc. duly epoxy

coated. Cutting, chases/holes in floors / walls / slab.Compliant with LABC. Weight

mass per unit area of DN100MM should not be less than 110.07kg/m3. sound levels

of not more than 15dBA as per EN 14366 at a flow rate of 4 l/s.including all core cut

,chases ,cutting making holes in all wall and floor as required complete in all respect.

16.2 MR 1.2 63mm o/d pipes Mtr RO 1546.81

16.3 MR 1.3 50mm o/d pipes Mtr RO 961.28

17 MR 2 Providing fixing, testing and commissioning in position Solfit SWR uPVC PIPE

TYPE-B pipe comforming to IS:13592 including all fittings such as bends,

junctions, inspection doors, offests, cowl, access pieces/clean out plugs, clamps

/supports/ hangers etc. jointing with PVC Adhesive joints including cutting holes

in walls, core cutting in slabs and making good the same. All complete as per

specification and direction of E/l.(For rainwater piping)

17.1 MR 2.1 160mm o/d pipes Mtr RO 1200.00

18 MR 3 Providing Fixing straight /offset type single body push fit type WC pan connector with

factory supplied spring loaded seal guard with integral single mould sealing fins

made of flexible EVA body, including bush/adaptor as supplied with the pan

connector (if required).

Providing and fixing floor drain (FD) with 50mm/40mm outlet and one 40mm inlet for

waste, with SS grating (adjustable height), having 50mm water seal and in-built NRV

Each RO 450.41

20 MR 5 Providing and fixing PP/UPVC trap of self cleansing design with screwed down or hinged

grating with or without vent arm complete, including cost of cutting and making good the

walls and floors :

20.1 MR 5.1 100 mm inlet and 100 mm outlet

20.1.1 MR 5.1.1 Sand cast iron S&S as per IS: 3989 Each 6 3986.29 23917.76993

21 MR 6 Providing and fixing PP/UPVC grating with Cockroach proof strainer of approved

design including setting in floor with cement motor to match with floor finish as per

architect requirement suitable for waster and FT.

22 MR 7 Providing and fixing PP/UPVC brass grating with frame of approved design including

setting in floor with cement motor to match with floor finish as per architect

22.1 MR 7.1 Size 100 mm X 100 mm Each RO 535

23 MR 8 Providing and fixing PP/UPVC extention piece for 100 mm dia floor trap formed

out of main pipe with multiple side inlets, suitable for various dia pipes including

all fixtures as required complete as per drawing approved sample and direction

of engineer in charge.

Digitally signed by PRIYA

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department (SHED-1 )

Construction of Administrative Building, PLUMBING WORKS DETAILED ESTIMATE

24 MR 9 Providing and fixing cast PP floor clean out plug with suitable insert keys for

opening, male threaded joint with threaded socket drip seal to soil / waste pipe as

required complete as per drawing approved sample and direction of engineer in

24.1 MR 9.1 Size 100 mm X 100 mm

25 MR 10 Providing and fixing rainwater khurra epoxy coated cast iron body outlet with flat

grate on balconies & terrace as required complete as per drawing approved sample

and direction of engineer in charge.

SUBHEAD III(Water Supply System(Internal))

26 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply, including all CPVC plain & brass

threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent cement and the cost of

cutting chases and making good the same including testing of joints complete as

per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc(inside

26.1 18.8.1 15 mm nominal dia Pipes Mtr 31.9 497.8 15879.82

26.2 18.8.2 20 mm nominal dia Pipes Mtr 28.6 537.6 15375.36

26.3 18.8.3 25 mm nominal dia Pipes Mtr 10.1 627.25 6335.225

26.4 18.8.4 32 mm nominal dia Pipes Mtr 25 739.3 18482.5

18.8.5 40 mm nominal dia Pipes Mtr RO

27 18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply and all CPVC plain & brass threaded fittings,

including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent cement and testing of joints

complete as per direction of Engineer in Charge.

Internal work - Exposed on wall(vertical & terrace area)

27.1 18.7.2 20 mm nominal dia Pipes Mtr 8 335.00 2680

27.2 18.7.3 25 mm nominal dia Pipes Mtr 8 401.55 3212.4

27.3 18.7.4 32 mm nominal dia Pipes Mtr 25 518.75 12968.75

27.4 18.7.5 40 mm nominal dia Pipes Mtr RO 702.95

28 18.18 Providing and fixing ball valve (brass) of approved quality, High or low pressure,

with plastic floats complete :

28.1 18.18.1 15 mm nominal dia Pipes Each 2 406.85 813.70

28.2 18.18.2 20 mm nominal dia Pipes Each 4 462.5 1850.00

28.3 18.18.3 25 mm nominal dia Pipes Each 3 464.05 1392.15

29.3 18.18.4 32 mm nominal dia Pipes Each 2 486.6 973.20

29 18.17 Providing and fixing gun metal gate valve with C.I. wheel of approved quality

(screwed end) :

30 MR 5 Providing and fixing Butter fly valve with nitrile seat and stainless steel stem with

lever operation and cast iron body in powder coated finish, suitable for test

pressure of 10Kg/sq.mm) with flanges, gaskets and necessary pad locking

arrangement complete required.

30.2 MR 5.2 80 mm i/d Each

31 MR 6 Providing and fixing thermal insulation in cold/hot water pipes a Polyolefin foam of

closed cell structure having thermal conductivity of 0.036 W/M.K at an average

temperature of 30 C. complete with 24 gauge aluminium sheet/cladding.

31.5 MR 6.4 40 mm dia pipe RM RO 86

31.6 MR 6.5 50 mm dia pipe RM RO 90

Digitally signed by PRIYA

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department (SHED-1 )

Construction of Administrative Building, PLUMBING WORKS DETAILED ESTIMATE

SUBHEAD IV(External Sewerage & Storm Water Drainage)

32 2.1 Excavating trenches by mechinical / manual means of required width for pipes,

cables, etc including excavation for sockets, and dressing of sides, ramming of

bottoms, for all depth, including getting out the excavated soil, and then

returning the soil as required, in layers not exceeding 20 cm in depth, including

consolidating each deposited layer by ramming, watering, etc. and disposing of

surplus excavated soil as directed, within a lead of 50 m :

32.1 2.10.1 All kinds of soil

2.10.1.2 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia Mtr 105 352.15 36975.75

33 Excavation of trenches in a Streets, Lanes or in Open Area for Storm Sewers and

Manholes to Full Depths as Shown in Drawings,excluding Shoring, Timbering of

Poling Board Frame System Type, dressing to correct sections and dewatering,

provision for diversion for traffic, protection of existing services i.e. telephone

cables ,electric lines, water supply lines and gas lines.night signals, profiles, Pegs,

Sight rails, boning rods, crossing over trenches for access to the houses,

watching, fencing etc., fixing and maintenance of caution boards, refilling

trenches, watering of refill in 15 cm layers, ramming and restoration of surface to

original conditions and removal of Surplus Spoil from the Site of Works, for all

Works other than connections to Ventilating Shafts upto a Lead of 15 mtr

33.1 MR 2.1 For depth not exceeding 2 m. below Ground level

All classes of soil except rocky Mtr 8.1 224 1814.4

34 19.6 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed

with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand)

including testing of joints etc. complete :

35 19.1 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement

mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc.

36 19.7 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with

R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone

aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand

(zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick

with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat

cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete

as per standard design :

36.1 19.7.1 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610

mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight

of cover 23 kg and weight of frame 15 kg) :

36.2 19.7.1.2 With Sewer bricks conforming to IS : 4885 Each 2 12711.80 25423.6

37 19.4 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick

masonry chamber with water tight C.I. cover with frame of 300 x 300 mm size (inside) the

weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per

standard design:

37.1 19.4.1 100x100 mm size P type

37.2 19.4.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Each 2 2707.65 5415.3

38 MR 7 Constructing catch basin 45x45 cm with bricks in cement mortar 1:4 (1 cement : 4

coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame

complete as per standard design :

38.2 MR 7.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Each 5 4500 22500

39 19.7 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as

per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section

as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with

minimum 112 mm space between protruded legs having 2 mm tread on top surface by

ribbing or chequering besides necessary and adequate anchoring projections on tail length

on 138 mm as per standard drawing and suitable to with stand the bend test and chemical

resistance test as per specifications and having manufacture’s permanent identification

mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement

concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal

size) complete as per design. Each 6 553.7 3322.2

40 19.21 Making connection of drain or sewer line with existing manhole including breaking into

and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand

: 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with

cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement

and making necessary channels for the drain etc. complete :

40.1 19.21.1 For pipes 100 to 250 mm diameter Each 1 810.45 810.45

TOTAL 162346.3

SUBHEAD V(External Water Supply)

Digitally signed by PRIYA

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department (SHED-1 )

Construction of Administrative Building, PLUMBING WORKS DETAILED ESTIMATE

43 18.14 Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe

and making long screws etc. complete (cost of water meter and stop cock to be paid

separately). Each 1 812.3 812.3

44 18.37 Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1

cement : 4 coarse sand) for water meter complete with C.I. double flap surface box

400x200x200 mm (inside) with locking arrangement and RCC top slab 1:1.5:3 mix (1 cement

: 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), including necessary

excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate

40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse

sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard

Digitally signed by PRIYA

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores

Department (SHED-1 )

Construction of Administrative Building, FIRE FIGHTING WORK

S.I MR DSR 2022 DSR 2022 MR

Description of Item Unit Total Qty

No Item No Item No Rate Amount Rate Amount

SUBHEAD I:FIRE HYDRANT SYSTEM

Supplying, installation, testing and commissioning of electric

driven terrace pump suitable for automatic operation and

consisting of following, complete in all respects, as required:

Horizontal type, multistage, centrifugal, split casing pump of

cast iron body & bronze impeller with stainless steel shaft,

mechanical confirming to IS : 1520

Suitable HP squirell cage induction motor TEFC type suitable

for operation on 415 volts, 3 phase, 50 Hz, AC supply with

IP55 class of protection for enclosure, horiziontal foot

mounted type with Class-'F' insulation, conforming to IS-325

M.S.fabricated common base plate, coupling, coupling

guard, foundation bolts etc.as required.

Suitable cement concrete foundation duly plastered and

with anti vibration pads

Providing, laying, testing & commissioning of 'C' class heavy

duty MS pipe conforming to IS 3589/IS 1239 including

Welding, fittings like elbows, tees, flanges, tapers, nuts

2 18.7 bolts, gaskets etc. and fixing the pipe on the wall/ceiling

with suitable clamp/support frame and painting with two or

more coats of synthetic enamel paint

of required shade complete as required :

Supplying and fixing single headed internal hydrant valve

with instantaneous Gunmetal/Stainless Steel coupling of 63

3 18.9 mm dia with cast iron wheel ISI marked conforming to IS

5290 (Type -A) with blank Gunmetal/Stainless teel cap and

chain as required

3.1 18.9.1 Single Headed Gunmetal Each 2 8183.514 16367.0276

Supplying, fixing, testing and commissioning of butterfly

4 18.11 valve of PN 1.6 rating with bronze/gunmetal seat duly ISI

conforming to IS 13095 of following sizes as required :

Providing, installation, testing and commissioning of non-

return valve of following sizes confirming to IS: 5312

complete with rubber gasket, GI bolts, nuts,washers etc.as

Providing, installation, testing and commissioning of

stainless steel Y-strainer fabricated out of 1.6 mm thick

stainless steel, Grade 304, sheet with 3 mm dia

holes with stainless steel flange.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe

with 63 mm dia male and female couplings duly bound with

GI wire, rivets etc. conforming to IS 636 (type-A) as required:

Digitally signed by PRIYA

Supplying and Fixing First Aid Hose Reel, wall mounting

swinging type complete with drum & bracket of MS

8 18.17 construction, spray painted in Post office Red, confirming to

IS 884/1995 with upto date amendments, complete with the

following as required.

20 mm nominal internal dia as per IS 12585 water hose

thermoplastic (Textile reinforced)Type II as per IS: 12585

20 mm dia. ball valve & nozzle.

Drum and brackets for fixing the equipments on wall.

Connection from riser with 25 mm dia gun metal stop valve

and M.S pipe as reqd.

Supplying & fixing 63 mm dia gun metal short branch pipe

with 20 mm nominal internal diameter size nozzle

9 18.18 conforming to IS 903 suitable for instantaneous connection

to interconnect hose pipe coupling as required:

Supplying and fixing orifice plate made out of 6 mm thick

stainless steel(Grade 304) with orifice of required size to be

10 18.13 fitted between flange &landing valve of external and 2 1413.866 2827.7326

internal hydrants to reduce presure at the outlet to the

level of 3.5 kg/sq.cm complete as required. Each

Supplying and fixing air vessel made of 250 mm dia, 8 mm

thick MS sheet, 1200 mm in height with air release valve on

top and flanged connection to riser, drain arrangement with

11 18.20 25 mo dia gun metal wheel valve with required accessories, 1 19526.55 19526.5532

pressure gauge and painting with synthetic enamel paint of

approved shade as required.

Providing and fixing standard fire man's axe with heavy duty

insulated rubber handle. Each

Providing and fixing fire hose cabinet fabricated from 16

gauge M.S. Sheet with single or double glazed front door

13 MR 13 (with 4 mm thick glass) and locking arrangement, painted

fire red with stove enamelled paint "FIRE HOSE" written on

front including necessary supports approximate size.

Providing and fixing dial type pressure gauge with isolation

cock and pipe at hydrant station.

14.1 MR 14.1 Diameter 100 mm calibration 0-8 Kg. Each 2 760.00 1520

Providing and fixing CO2 type fire extinguishers with steel

cylinder with a discharge valve and conforming to IS:15683.

Extinguishers shall be painted with rex enamel paint and

fixed to wall with brackets capacity 4.5 Kg. Each

Providing and fixing ABC powder type fire extinguisher

suitable for inverted operation and fabricated from 1.6 mm

M.S. sheet internally protected with anticorrosive treatment

and hydraulically tested to a pressure of 25 Kg/Sqcm.

Extinguishers externally painted with red enamel and fixed

to wall with brackets complete with internal charge and

spanner (Conforming to IS:15683 capaicity 6 KG.).

Digitally signed by PRIYA

(SCHEDULE OF QUANTITIES)

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department (SHED-

ADMINISTRATIVE BUILDING

DSR Rate Amount

S.No. Description Unit Qty

A SCHEDULE ITEMS

WIRING AND SUB MAINS

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm

FRLS PVC insulated copper conductor single core cable in surface / recessed

1 1.3.3 heavy class Steel conduit, with modular switch, modular plate, suitable GI box and Point 90 1845.00 166050.00

earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single

core cable etc as required.a) Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable in surface / recessed Steel conduit, 2 way modular

switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS

PVC insulated copper conductor single core cable etc as required

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor

3 1.5 single core cable in surface/ recessed Steel conduit alongwith 1 No 4 sq. mm FRLS Point 900 433.00 389700.00

PVC insulated copper conductor single core cable for loop earthing as required

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor

4 1.6 single core cable in surface/ recessed Steel conduit alongwith 2 Nos 4 sq. mm metre 10 662.00 6620.00

Wiring insulated

for circuit/ copper wiring

submain conductor single earth

alongwith core cable

theearthing assizes of

5 1.7 FRLS PVC insulated copper conductor, single core cable in surface/ recessed Steel

conduit as required.

a 1.7.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire metre 400 369.00 147600.00

b 1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire metre 250 428 107000.00

b 1.7.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire metre 5 589 2945.00

d 1.7.5 2 X 10 sq. mm + 1 X 6 sq. mm earth wire metre 5 710 3550.00

e 1.7.9 4 X 6 sq. mm + 2 X 6 sq. mm earth wire metre 15 924 13860.00

f 1.7.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire metre 10 1166.00 11660.00

g 1.7.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire metre 15 1645.00 24675.00

Supplying and fixing suitable size GI box with modular plate and cover in front on

6 1.31 surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket Each 23 477.00 10971.00

outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to

Supplying and fixing suitable size GI box with modular plate and cover in front on

7 1.32 surface or in recess, including providing and fixing 6 pin 15/16 amps modular socket Each 22 586.00 12892.00

outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing of following modular switch/ socket outlet on the existing

8 Modular plate & switch including connection but excluding modular plate etc. as

a 1.24.1 5/6 amps switch Each 2 103 206.00

b 1.24.4 3 pin 5/6 amp socket outlet Each 47 122 5734.00

d 1.24.5 6 pin 15/16 amp socket outlet Each 2 197 394.00

e 25 amp switch Each 10 200 2000.00

9 1.27 Supplying and fixing following size/ modules, GI box Boxes alongwith modular base

& cover plate for modular switches in recess etc as required.

a 1.27.1 1 or 2 Module (75mmX75mm) Each 10 298 2980.00

b 1.27.2 3 Module (100mmX75mm) Each 2 327 654.00

c 1.27.3 4 Module (125mmX75mm) Each 2 343 686.00

10 2.18 Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with

2 pole and earth, metal enclosed plug top along with 20 amps "C" curve, SP, Each 1 1621.00 1621.00

MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover

11 1.25 Supplying and fixing stepped fan regulator on the existing modular plate switch box

including connections but excluding modular plate etc. as required. Nos. 14 369.00 5166.00

12 Supplying and fixing of 16 SWG M.S. Fan Box 12.5" Rod but without fan cover

(hylam sheet). as required. Nos. 14 200 2800.00

13 Supplying and fixing of fan cover (hylam sheet).on the existing Fan Box as required.

14 Supplying and fixing of modular Blanking plate on the existing modular plate &

switch box excluding modular plate etc. as reqd.

Digitally signed by PRIYA

(SCHEDULE OF QUANTITIES)

NAME OF WORK: Construction of 250mx30m of shed with 25 Tons (Revised) EOT Crane facility in General Store Area of MM- Stores Department (SHED-

ADMINISTRATIVE BUILDING

DSR Rate Amount

S.No. Description Unit Qty

15 1.24 Supply and fixing following modular switch/socket on the existing modular plate and

a cover plate socket

1.24.6 Telephone & switch box including

outlet. (RJ - 11) connections but excluding modular plate etc. as Each 14 148.00 2072.00

b 1.24.7 TV antenna socket outlet Each 2 148.00 296.00

16 1.27 Supplying and fixing following size/modules, GI box along with modular base and

1.27.1 1 or 2 plate

Modulefor(modular

75mm ) in recess etc as required. Each 18 298.00 5364.00

18 1.18 Supplying and drawing following pair, 0.5 sq.mm FR PVC insulated copper

1.18.2 2 Pair unarmoured telephone cable in the existing surface / recessed steel /

19 1.27.1 Supply, laying, testing and commissioning of the following co-axial PVC insulated

a conductor cable in existing surface / recessed conduit etc. and including making

20 1.53 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/

1.53.1 1 Steel/ PVC conduit/ raceway as required.

run of cable Metre 250 57.00 14250.00

b 1.53.2 2 run of cable Metre 60 96.00 5760.00