8413/E8 Maint and Repair/Replacement of CI/GI Pipe lines and repair to submersible pumping sets, sewage pumping sets water treatment and water supply installation at RTS and Depot Hempur under GE (East) Bareilly

Amount

Lifting/taking out defective submersible pump of any capacity alongwith column pipe of any size and submersible cable, dismantling the pump from motor, setting aside for repair /servicing / overhauling including lowering the pump set into borewell replacement of packing and nut bolts (if required) and testing after the completion of repair works in the presence of JE/ Engr in charge .

Disconnections of electric connection of the starter of 15/25/35 HP Pumping set for repairs installed at LT Panel in the pump house, carefully checking the parts throughly & replacement of unseviceable parts such as electronic Motor Protection relay with inbuilt earth fault protection, Over load protection relay ranging 16 -100Amp, MNX-16-100 contractor, NO-NC for starter, (Front add on auxilary contact block) and electronic timers multi time setting type, 240/415 Volt, 50 Hz of range, complete all as specified & directed. Make- L &T / Havells/Minilec. Note :- Spare parts to be measured and paid seperately in respective items.

M&L for preparation of old concrete/plastered surfaces by scrapping , brooming etc and applying two coats of exterior emulsion weather proof paint (Apex of Asian paints or equivalent) over dome, wall, columns ,beams including all pipe lines etc of overhead reservoir using scaffolding & necessary safety precaution complete all as specified and directed for the following RCC over head reservoir:- (a) RCC overhead reservoir 10000 gallon capacity, 50 to 60 feet staging.

(b) RCC overhead reservoir 25000 gallon capacity, 50 to 60 feet staging. Note for Item No (a) & (b) :- Colour status shall be as under :- (i) Rising main - Blue colour. (ii) Delivery main - Green colour. (iii) Washout main - Red colour. (iv) Overflow main - Yellow colour.

M&L seven stage cleaning and sterilization inside the Over head tank/underground sump / semi under ground sump of 25,000 Gallons capacity through bacteriological treatment by using TERBACK G5 TERBACK G10 TERBACKG65 and UV RAY by involving the following seven (7) stages of cleaning process including cleaning the external surfaces, structure for all scales and other particles any algae, hives and any type with cement and sand mortar (1:4) and applying one coat of white wash to internal surface when became dry and two coat of white wash to external surface complete all as specified and directed. Seven (7) stages of cleaning process as under : (a) First stage is to draining out the reserved water by using exit valve or high capacity pump of dewatering system. (b) Second stage is cleaning all the the algae formation inside the tank removing all scale, dirt, mud inside the tank by using TERBAC G10 Chemical complete. (c) Third stage is scrubbing the walls and floor with mechanized scrubber & fresh water cleaning by high speed jet pump (rotary & flat) to remove all scaling, algae and other formed particles on internal surfaces of the tank completely. (d) Fourth stage is first bacteria screening i.e de-verification by using TTERBACK G5 chemical complete. (e) Fifth stage cleaning the floor of the water tank by heavy duty industrial vacuum cleaner and sludge sucker maximum 1200 W with suitable heavy duty rugged motor to make sump free of any foreign and loose particles of any nature. (f) Sixth stage is second bacteria screening and sterilization method by using UV RAYS by heavy duty UV radiation which shall have 360 degree of sterilization with in the tank to kill all suspended bacteria (The radiation shall portable and effective for sterilization of drinking water tanks for diminution of floating and suspended bacteria).

(g) Seventh stage of cleaning and third screening is to sterilize the floor and wall of the water tank by using laboratory certified branded strong TERBACK G65 or equivalent any non toxic bio-degradable eco-friendly anti-bacterial agent certified by a Govt. approved laboratory to disinfect the tank from all harmful pathogens. Note : (i) Entire T& P should be arranged by the contractor at their own. Only electric power & water shall be supplied by MES at all stipulated rate. (ii) “Date of cleaning” should be written over the outer surface of tank by synthetic enamel paint with lettering not less than 100 mm height. (iii) All safety equipments required like safety helmets, Gumboots, safety belt, mask, safety goggles and necessary insurance for safety of working labors to execute the work is responsibility of the contractor and rates quoted shall be deemed to inclusive of the same. (iv) Contractor will submit Govt laboratory test certificate of TERBAC-G5, TERBACG-10 AND TERBAC G-65.

All as per Srl item No 4.00 here in before but capacity 10000 gallon.

Dismantling and Taking up or down steel tubing and connections,including cleaning for refixing including separting the serviceable pipes/tubes cleaning the same deposit to E/M store yard complete all as specified and directed.

Bore of pipe 80/100 mm

Bore of pipe 40/50mm

Bore of pipe 25 mm

Bore of pipe 20 mm

Bore of pipe 15 mm

Re-laying, jointing old GI tubing and connections in new or old position including new fittings such as bends, elbows, union, tees, reducers etc; as required at site laid in trenches or on floors complete all as specified and as directed of the following sizes :- Note :- Excavation and other earth work will measured and paid separtely for steel tubes / pipes laid in trench

Bore of pipe 100 mm

Bore of pipe 80 mm

Bore of pipe 50 mm

Bore of pipe 40 mm

Bore of pipe 25 mm

Bore of pipe 20 mm

Bore of pipe 15 mm

Supply, Laying, jointing and leakage testing GI Pipe medium grade including all fittings such as bend, tee, elbow, union, reducer etc, laid in trenches and including dismantling and taking down unserviceable / cracked steel tubing with all fittings of the following sizes as complete all as specified and as directed at site of the following sizes :- Note :- Excavation and other earth work will measured and paid separtely for respective items.

100 mm dia

80 mm dia

50 mm dia

40 mm dia

25 mm dia

20 mm dia

15 mm dia

S&F Gun-metal, globe or Gate Valve with iron wheel head, screwed bothe ends for iron pipe, ISI marked including taking down of unserviceabel existing gate valve complete all as specified and directed of the following sizes:-

80 mm dia

50 mm dia

40 mm dia

25mm dia

20mm dia

15mm dia

S&F of 'D' Joint of following bore complete all as specified and directed.

(a) 80mm bore

(b) 100 mm bore

(c) 150 mm bore

M&L for repair / rectification of leakage / blockage to water supply distribution lines of following bore of GI tubing by necessary excavation, returning / filling as required, tightening of lose joints of union, elbow, socket, nipple as per site requirement including for replacement of GI union, socket, nipple as required complete all as directed.

(a) 15mm bore to 20mm bore

(b) 25 mm bore to 40mm bore

(c) 50 mm bore

M&L for dewatering complete trenches manually for repairing joints by cocking and inserting spurn yarn and Run lead joint, making good/ leakless the existing joint including necessary excavation and earth work like returning, filling etc for pipes of following bore complete all as directed.

(a) 80 mm bore

(b) 100 mm bore

(c) 150 mm bore

M&L for dewatering complete trenches,Repair/rectification of leakage and blockage of PPR pipes manually repairing joints by inserting proper accessories and fittings of PPR pipes making good/ leakless the existing joint including necessary excavation and earth work like returning, filling etc for pipes of following bore complete all as directed.

(a) 110 mm bore

(b) 90 mm bore

(c) 75mm bore

M&L for provision of new wash out points by proper cutting and screwing of existing DI/CI/GI pipe fixing reducer tee of suitable size, supplying and fixing, Jointing, testing CI sluice valve of following size by fixing 02 Nos at each wash out point with flanged ends including necessary mountings nuts, bolts washers and packing fibers gasket on both end and making pit chamber including iron frame cover 3.15 mm thick with locking arrangements complete all as specified and directed.

(a) Wash out point at 150 mm bore pipe

(b) Wash out point at 100 mm bore pipe

(c) Wash out point at 80 mm bore pipe

Supply & laying / fixing in floor / trench, 3 layered (outer green coloured UV stabilized, middle black coloured UV stabilized and innermost layer white coloured with anti-microbial property) fusion welded PP-R (polypropylene Random Co-Polymer) pipes of size PN-16, 75mm OD (SDR– 7.4), ISI marked including plain PP-R fittings and brass threaded PP-R fittings such as flanges, elbow, bend, sockets, tee etc. as required at site and testing of joints including taking down PP-R and PVC pipe and connections complete all as specified and as directed

All as per Srl item No. 15.00 here in before but PN-16 pipe, 90mm OD (SDR – 7.4)

S&F in replacement PPR gate valve (brass insert) of size 75 mm bore including connection and testing complete all as directed.

S&F in replacement PPR gate valve (brass insert) of size 90 mm bore including connection and testing complete all as directed.

M&L for screwing existing steel tubing of bore 40/50mm in position for alterations or additions (or lengthening screw on pipe to form connector) complete all as specified and as directed.

M&L for screwing existing steel tubing of bore 25/20 mm in position for alterations or additions (or lengthening screw on pipe to form connector) complete all as specified and as directed.

Supply and laying of centrifugally cast (Spun) ductile iron pressure pipe with spigot & socket end, class K-9 in any length laid in trenches, conforming to IS-8329/2000 with cement mortar lining with and including rubber gasket jointing conforming to IS-15382/ tyton joint and including dismantling and taking down unserviceable / cracked DI pipe with all fittings complete all as specified and directed for the following sizes:-

80 mm dia

100 mm dia

150 mm dia

Supply and fixing DI fittings for Flanged pipe, DI Bends, connecting pieces, bell mouth pieces, tapers, tee pieces of one end flanged and other end spigot or socket upto 150 mm bore complete all as specified and directed.

M&L for Rubber gasket joint Spigot and socketed pipes and fittings for the following bore complete all as specified

80 mm dia

100 mm dia

150 mm dia

Taking up cast iron water mains (including all fittings),with spigot and socket ends and lead joints including burning out joints and recovering lead complete all as specified and directed for the following sizes:-

80 mm dia

100 mm dia

150 mm dia

Supply and laying in trenches of CI Pipe centrifugally cast, spigot & socket ends pipes, Class LA, including all fittings with lead Joints and including dismantling and taking down unserviceable/cracked CI pipe with all fitting burning out joints and recovering lead complete all as specified and directed for the following sizes:-

150mm dia

100mm dia

80 mm dia

M&L for run lead joint Spigot and socketed pipes and fittings for the following bore complete all as specified

80 mm dia

100 mm dia

150 mm dia

Supply and fixing CI fittings for Socketed pipe, CI Bends, connecting pieces, bell mouth pieces, tapers, tee pieces of one end flanged and other end spigot or socket upto 150 mm bore complete all as specified and directed.

M&L for lead wool joint Spigot and socketed pipes and fittings for the following bore complete all as specified

80 mm dia

100 mm dia

150 mm dia

M&L for boring the holes under roads pavements, hardstanding by treanch less techonology, using ultrasound technique and necessary machine including DI/CI/GI/HDPE/PP-R Pipe of 25 mm to 150 mm bore suitable for 0.4 mpa working pressure complete all as specified and directed.

M & L for construction of brick masonry valve pit of size 90x90x90cm (internal dimension) one brick thick wall built in CM (1:4) on 100mm thick PCC (1:4:8) type D2 (using 40mm graded crushed stone aggregate) as in foundation, and 15mm thick rendering in cement mortar (1:4) both externally and internally, external plaster shall be up to 15cm below GL, providing valve pit cover made of 3.15mm thick MS sheet/plate, including provision of hinges, handle and locking arrangement including 40 X 40 X 5mm angle iron frame fixed on top of valve pit by means of MS hold fast 40x5mm and 150mm long, embedded in PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) including two coats of anti-corrosive paint over a coat of red oxide zinc Chrome primer and necessary earth work in soft/loose soil including demolition of old unserviceable existing valve pit & pit cover complete all as specified & directed.

Dismantling and taking out sluice valve any size and ,M&L for repair sluice valve for 80 mm to 200 mm bore , high tensile stainless steel spindle, including nuts, bolts and gas kit ,glands and refixing after repair etc. complete all as specified and directed.

S&F in repair sluice valve class PN-1.6 heavy duty flanged ends drilled ISI marked confirming to IS: 14846, wheel operated (Handle) with high tensile stainless steel spindle, including nuts, bolts and jointing with jointing materials etc. complete including taking out old existing unservicable sluice valve including making arrangement for safe working all as specified and directed.for the following sizes:- Make: BIR, KIRLOSKAR ,Kartar or Equivalent as approved by GE.

150 mm dia

100 mm dia

80 mm dia

S&F CI Non Return Sluice Valve flanged ends of class 1.6 PN, including taking down old existing unserviceable Non Return Valve complete all as specified and directed for the following sizes:- Make: BIR, KIRLOSKAR ,Kartar or Equivalent as approved by GE.

150 mm dia

100 mm dia

80 mm dia

Supply and fix Green & Red button operated push type, Star delta Starter fully automatic suitable for 415 V, AC, 3 phase ,50 Hz suibtable for 5 HP Submersible Pump and Motor complete with Over load tripping circuit (Max relay (14-20 Amp), Reverse phasing , unbalancing, Low voltage , high voltage upto motor terminal and starting time delay and should be housed in Dust proof, Moisture proof and powder coated sheet metal fabricated box with locking arrengement including taking down of existing starter complete all as specified and directed.

Supply and fix Green & Red button operated push type, Star delta Starter fully automatic suitable for 415 V, AC, 3 phase ,50 Hz suibtable for 12.5/15 HP Submersible Pump and Motor complete with Over load tripping circuit (Max relay (25-60 Amp), Reverse phasing , unbalancing, Low voltage , high voltage upto motor terminal and starting time delay and should be housed in Dust proof, Moisture proof and powder coated sheet metal fabricated box with locking arrengement including taking down of existing starter complete all as specified and directed.

M&L for Painting to pipe of pump house rising mains hydrants, sluice valves, pipe, fittings, NRV, discharge head etc after cleaning, scrapping and making the surfaces free from rust of main externally and painting with two coats synthetic enamelled paint in black / blue / red including marking / writing on pipe etc complete as specified and directed.

Dismantling the submersible pump assembly capacity 15 HP completely, checking and segregating serviceable / unserviceable parts, cleaning serviceable parts thoroughly by approved method, replacement of wron out parts including necessary lath / machinery work including all new parts as reqd, re-assembling the pump completely lowering the pump alongwith all accessories to the existing location, overhauling, commissioning, testing and connecting up complete including painting all as specified and directed.

Supply and Replacement of following pairs suitable for srl item No 38.00 for Submersible pump:-

(a) Discharge outlet

(b) Stage casing

(c) Pump shaft

(d) Key for impeller

(e) Key for pump coupling

(f) Bearing sleeve

(g) Stage Bowl bush

(h) DOL Bush

(j) Nut Stud kit

Dismantling, cutting and removing the burnt windings from the submersible motor of capacity 15 HP, rewinding with suitable size / gauge of super enameled / copper conductor and other approved insulating materials, heating, drying and replacement of existing size of submersible cable including varnishing, overhauling, reassembling the motor, installing, commissioning, testing and connecting up complete all as specified and directed.

Supply only of following parts suitable for ser item No 40.00 for Submersible motor :-

(a) Oil Seal Set

(b) `O` ring set

(c) Motor bearing Bush set

(d) Complete Pad set (Bearing assembly)

(e) Rotor sleeve set

(f) Thrust plate with ferredo lining

(g) Upper/Lower bearing house

(h) Balancing ring

Disconnections of electric connection of centrifugal pump and motor capacity of 25 HP, lifting and removing motor form its existing foundation to the location (in side/outside of building) where directed by the Engr-in-charge. Dismantling the pump and motor of capacity 25 HP, carefully checking, segregating serviceable and unserviceable parts, cleaning the serviceable parts thoroughly by approved method (Pats like stator, rotor, terminal box, bearings shaft, key etc) heating, drying & varnishing including replacement of burnt winding for 25 HP motor with super enameled copper wire of existing gauge and good quality of insulating materials including replacement of unserviceable parts as required including necessary lath / machining work. Reassembling the pump and motor including painting with two coats of synthetic enamel paint after necessary surface preparation, marking of number (SM, MES or srl No) installing to its existing foundation, commissioning, connecting up and testing complete as directed. Note:- Spares shall be measurded and paid separately under respective items.

Supply only of following parts suitable for ser item No 42.00 for centrifugal pump and motor complete as directed..

(a) 25 HP Pump Bearing No 6310 or suitable size

(b) Pump bearing seat suitable for 3 ph 25 HP motor

(c) Motor side cover suitable for 3 ph 25 HP motor

(d) Motor connected plate six hole suitable for 3 ph 25 HP motor

(e) 25 HP Motor Bearing No 6308 or suitable size

(f) 25 HP Motor Bearing No 6309 or suitable size

M&L for Dismantling the Sewage pump set up to 5 HP, carefully checking, segregating serviceable and unserviceable parts, cleaning the serviceable parts thoroughly & including replacement of unserviceable parts as required (Block piston, Nozzle, head block, cupling engine parts & Impaller, gland packing, Pump shaft, pump seal Pump parts) including necessary lath / machining work. Reassembling the pump and engine parts including painting with two coats of synthetic enamel paint after necessary surface preparation, marking of number (SM, MES or srl No) & replacement of unserviceable suction & Delivery PVC pipe, flange, clamps, foot valve etc and testing complete as directed.

Supply and fix Green & Red button operated push type, Star Delta Starter Oil mersed with Single Phase Preventer, Type designation BSA, Operatig current 28Amp, coil voltage 380 _+15% , 3 phase 415V 50 Hz suibtable for 25 HP Centrifugal Pump and Motor complete with Over load tripping circuit (Max relay (20-40 Amp), Reverse phasing , unbalancing, Low voltage , high voltage upto motor terminal and starting time delay and should be housed in Dust proof, Moisture proof and powder coated sheet metal fabricated box with locking arrengement with extra long life contact with arrengement including taking down of existing starter complete all as specified and directed . Make- Kapil SKN or equivalent

Supply and fix DOL starter three phase 415 volt 50 Hz push button type suitable for 05/7.5 HP centrifugal pump set with arrangement and making the necessary connection in panel and pump set including taking down of existing starter complete all as specified and directed. Make- L&T or equivelent as approved by GE

S&F in repair electric shock treatment chart coloured of size approximetely 90 x 60 x 6 mm thick plywood with wood frame including covered with plastic laminated sheet complete all as specified and directed.

S&F in repair machinary maintenance chart coloured of size approximately 3 ft x 2 ft & 6 mm thick plywood with wood frame including covered with plastic laminated sheet complete all as specified and directed.

M&L for trimming vegetation or small inequalities clearing all grass vegetation, saplings, shrubs, brushwood, roots, and tree of surroundings area up to 500 sq mtr including cleaning and removing rubbish upto a distance of 50 mtr outside the periphery of the area under clearance of water supply installations complete all as specified and as directed.

S&F in repair for Aviation light on OH tank 18/21 mtrs staging (on top of OH tank) with all fittings, fixtures and accessories including 2.5 sqmm wire Three core in 20 mm PVC conduit from light to connection points including 2-way MCB DB with isolator (10 Amp) capacity complete all as specified and directed.

Supplying, Laying, jointing and testing 2.5 Sq mm 2 core, PVC insulated, armoured, heavy duty, Copper conductor cable 1100 volts grade, laid in trenches / ducts, floors, fixed to pole / walls etc. complete all as specified and directed.

S&F in repair for glow sign board (box type) LED of required size 3600 x 600 x 300 mm made out of MS sheet of suitable size with sheet fixed on front and quality marked with details of Pump House etc on front and rear with different colours including provision of LED power- fittings & fixtures in equal distance to illuminate board including connections with 2.5 sqmm single core stranded copper conductor cable and writing with 10 mm size letters as specified and directed .

Supply & fix in repair 1100 volts grade heavy duty cable PVC insulated aluminum conductor screened served with inner sheathing of PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 meter apart including 4mm GI suspension wire, one twin core cables flat or circular of size 10 Sqmm etc complete all as specified and directed.

S&F in repair Off load change over switch 100 Amp, 4 pole, 415 Volts, 50 Hz, complete all as specified and directed

S & F in replacement of LED Post top lantern 45 watts made in cast aluminium with innovative glare free indirect lighting distribution and IP65 protection for differnt applications suitable for mounting on pole dia 50 mm, complete all as specified and directed. Make: C&S/Havells/Bajaj/Phillips / Crompton as approved by GE.

S&F in repairs GI bracket made out from GI pipe 25/32mm dia, 1.20 m long fixed on wall with and including nut, bolts and GI clamps of size 25x4mm as required & including painting etc complete all as specified & directed.

S & F in replacement of LED Bldg Security light fitting 30 Watts, 6500 K, 230 Volts, AC, Outdoor type Street Lights with high pressure die cast aluminium housing andbest in class design & Robust heat sink along with class leading IP, IK & Surge protections for long lasting performance including connecting up with driver three core flexible copper conductor cable of suitable size, lamp & IP 65/66 protection, complete all as specified and as directed. Make: C&S/Havells/Bajaj/Phillips / Crompton as approved by GE.

M&L for Earthing complete with using GI earth plate electrode 600x600x6.0 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 mtr below normal ground level and earth plate surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness off 15 cm all around the plate with using GI Strip 25 x 4mm as earth lead moulded and retreived to earth plate at one end and connected to main switch / control board at another end with and including 15 mm dia GI light grade from upper end of earth plate upto external face of the wall of the building including 20 mm dia bore GI pipe light grade as water pipe from chamber to upper edge of the plate GI funnel with wire mess fixed on water pipe and provison of PCC 1:2:4 type B-1 (Using 20 mm Dia graded stone aggregate) duly reinforced with mild steel round bar 6 mm dia @ 150 mm c/c both ways with 10 mm dia mild steel bars as in lifting handle with and including necessarry excavation and earth work including laying the pipe concealed in floor / wall allas per plate NO-3 of SSR Part-I complete all as specified and directed and testing on completiopn (Note:- If the desired resistance is not found earthing shall be done by the contractor at no extra cost to Govt).

M & L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 25 x 4mm galvanised iron strip, complete all as specified and as directed.

S & F in repairs of MCB TPN DB 4 Way, (4+12) suitable for flush mounting and surface mounting, conforming to IP 43 - IK 09 with acrylic door with 100 Amp copper bus bar for each phase, complete with din rail, Neutral and Earthing bar after taking out the old unserviceable DBs, connection complete and making good the disturbed surfaces complete all as specified and as directed.

S & F in repairs of DX3 AC MCB SP, 240 Volt, 6 to 32 Amp, 10 KA, ISI Marked, "C" Curve, IP 20 Protected terminals, Complete all as specified and as directed.

S & F in repairs of DX3 AC MCB TPN, 415 Volt, upto 63 Amp, 10 KA, ISI Marked, "C" Curve, IP 20 Protected terminals, Complete all as specified and as directed.

Supply only Calcium based granularhypo chlorite 65% to 70% disinfectant for water treatment, Packing in 45 Kg, plastic drums complete all as specified and directed.

M&L MCCB 4 pole, 415 Volt, fixed type 125 to 160 amp with breaking capacity 36 Ka complete all as specified and directed.

M&L MCCB 4 pole, 415 Volt, fixed type 160 to 200 amp with breaking capacity 35 kA complete all as specified and directed.

Repair and servicing of powder base dosing plant for smooth functioning including necessary spares as required for rectifying the defects for smooth functioning for the following plants :- Location :- (i) The cost of complete spares, rewinding & repair of mixing motor is deemed to be included in the quoted rate. (ii) All testing equipments to be avaliable in installations.

Taking out connection of Chlorine / Altoch dosing system , detecting fault and repair /replacement of unserviceable parts and refixing same after completion job and connecting dosing system and testing complete all as specified and directed. (NOTE: Spares parts shall be measured and paid separately as Supply only)

Supply and fixing in repairs rotor assembly with bearing brackets and tolerance rings suitable for decree dosing pump complete all as specified and directed.

Supply and fixing in repairs pump tube suitable for dosing pump complete all as specified and directed.

Supply and fixing in repairs injector assembly suitable for dosing pump complete all as specified and directed.

M&L MCCB 4 pole, 415 Volt, fixed type 63 to 100 amp with breaking capacity 16 Ka complete all as specified and directed.

Supply and fixing in repairs weighted suction line stainer suitable for dosing pump, complete all as specified and directed.

Supply and fixing in repairs Agitator Motor electric driven 230 Volts, 50 Hz, Single phase,120 W, 900 RPM copper wounded, complete all as specified and directed.

Supply and fixing in repairs PVC pressure hose pipe upto 10 to 20Kg/cm2 as per existing size, complete all as specified and directed.

S&F in repairs Digital multi programmable electronic timer capacity for 24 hrs clock, 3 phase, 415 volts, 50 Hz, complete all as specified and as directed.

S&F in repairs electronic Single phase preventer operation on 415 volts 50 Hz all as specified and as directed.

M & L for Grass and weeds killer chemical 5 Ltrs capacity of make Roundup, complete all as specified and directed.

S&F LT rubber mat of size 1.0mx2.0mx12 mm at water supply installations, complete as specified and directed.

S&F pressure gauge of dial 30 to 60Kg/cm2, suitable for fixing at MS pipe 100/150 dia header with all fiting and fixtures etc, complete as specified and directed.

S&F Over load protection relay suitable for 5HP to 25HP monoblock/centrifugal /submersible motors of make L&T all as specified and directed.

Supply and fix in repair MNX contactor 16Amps to 40Amps, 3 Pole with NO and NC complete all as specified and directed. Make : L & T.

Supply and fix in repair MNX contactor 63Amps to 100 Amps, 3 Pole with NO and NC, complete all as specified and directed. Make : L & T.

Supply and fix in repair spare kit for MNX contactor 16Amps to 100 Amps, 3 Pole, complete all as specified and directed. Make : L & T.

S&F in replacement of PVC bib tap 15 mm.bore, complete all as specified and directed

S&F in replacement MS ERW column pipe screwed 125 mm nominal bore having wall thickness not less than 7.11 mm electric resistance welded with MS flanged 16 mm thick heavy duty confirming to IS 6392 incl 2 mm thick rubber sheet and steel nuts and bolts 10 mm long with washer etc, complete as specified and directed.

(a) 100 mm nominal bore.

Take the water sample from the bore well at PH No.1, 2, 3, 4 & 5 and two consumer end and send it for physical / Chemical / Bateriological test from any recognised govt agency and provide its report to Engr in charge.

S& F in replacement submersible pump/motor 15 HP, Electric driven, 415 Volts, TP suitable for bore well casing pipe 200/250 mm, Head 70-90Mtr, 2250 LPM, Vetrical type, complete all as specified and directed. Make:-CRI / KSB / KIRLOSKAR

S& F in replacement submersible pump/motor 10 HP, Electric driven, 415 Volts, TP suitable for Open well/Semi UG Sump, Output dia- 80/100 mm, Head 70-90Mtr, 2250 LPM, Horizontal type, complete all as specified and directed. Make:-CRI / KSB / KIRLOSKAR

All as per above Sch "A" item No 135.00 here in before but 5 HP,415 Volts, TP.

S& F in replacement submersible pump/motor 1.0/1.5 HP, Electric driven, 230 Volts, SP suitable for Open well/Semi UG Sump, Output dia- 20/25 mm, Head 70-90Mtr, 120-150 LPM, Horizontal type, complete all as specified and directed. Make:-CRI / KSB / KIRLOSKAR

S& F in replacement submersible pump / motor 01/02 HP, Electric driven, 230 Volts , SP, suitable for 25/20mm dia output, bore well casing pipe size 100/150 mm, Head 70-90 Mtr, 100-150 LPM, Vetrical type, complete fitting/fixtures with starter panel, complete all as specified and directed. Make:- CRI, KSB and KIRLOSKAR.

S& F in replacement Monoblock self priming HI-Flow pump/motor 01/02 HP, Electric driven, 230 Volts , SP suitable for 25/20mm dia output, Head 70-90 Mtr, 120-150 LPM, complete fitting/fixtures with starter panel, complete all as specified and directed. Make:- CRI, KSB and KIRLOSKAR.

Supply fixing testing and commissioning submersible cable flat 10.0 sqmm x 3 core PVC insulated and PVC sheathed with multi stranded copper conductor 1100 volts grade fixed to submersible motor column pipe using suitable size of clamps made out of stainless steel flat of size 20x2 mm with steel nuts bolts & washer foe every column pipe of 3 mtr lenght all as specified and directed.

(a) 6.0 sqmm x 3 core..

(b) 4.0 sqmm x 3 core..

(c) 2.5 sqmm x 3 core..

Supply, install, testing and commissioning of Mild steel chlorine gas cylinder suitable for 100Kg capacity with filling lequid chlorine gas, industrial type as manufacturer recommended pressure for usage of drinking water treatment for improving taste, safety and odour of drinking water, highly reactive, reliable, optimum quality to kill Bacterial organisms at public properties, complete all as specified and as directed.

Supply, install, testing and commissioning of Remote wall/floor panel mounted Vacuum Chlorinator (regulator) for reduces the gas from a varying supply pressure 10kg- 75kg capacity with safety kit complete set suitable for disinfection of water through gravity feed, Vaccum feed or motor feed chlorination by main water supply/swimming pools/sewage water treatment etc, complete all as specified and directed.

M&L for Solar street light 45watts, alongwith battery backup complete cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-22 (8.5 metre Long) and applying one coat of steel primer and one coat of aluminium paint and pole ser number as per existing number including Earth work, excavation, foundation, PCC 1:3:6 type C-2 and coping in PCC 1:3:6 type C-1 of pole complete all as specified and directed by Engineer -in-Charge.

Supply & erection of Water CO2 type Extinguisher 9 ltr capacity in HP Mild Steel Cylinders ISI marked / approved fitted with pressure indicating gauge, internal tube, squeeze lever type valve fully chaged with Foam compound complete in all respects including wall suspension braket and conforming to IS:15683

Supply & erection of ISI marked (IS:15683) Fire Extinguisher seamless construction, Carbon-di-oxide type capacity 4.5 Kg.flat base including valve, discharge hose of not less than 10 mm dia., 1M long and complete in all respects incuding initial fill with CO² gas conforming to IS:307-1966 filled to a filling rate of not more than 0.667 and with wall suspension bracket.

Supply & erection of 6 kg capacity ABC (Powder type) Fire Extinguisher in HP Miled Steel Cylinders ISI marked / approved fitted with pressure indicating gauge, internal tube, squeeze lever type valve fully chaged with ABC powder (Mono Ammonium Phosphate) pressured by Nitrogen complete in all respects including wall suspension braket and conforming to IS:15683.

Supply & erection of 9 kg capacity ABC (Powder type) Fire Extinguisher in HP Miled Steel Cylinders ISI marked / approved fitted with pressure indicating gauge, internal tube, squeeze lever type valve fully chaged with ABC powder (Mono Ammonium Phosphate) pressured by Nitrogen complete in all respects including wall suspension braket and conforming to IS:15683.

Supply, installation, Commisioning and testing for Chemical dosing system metering type, capacity to deliver 14- 27 LPH max & adjustable from 10% to 100% through Knob and suitable to inject against 5-10Kg/cm2 pressure duly operated by 240V, Single phase power supply, Chemical Solution preparation tank of 200 Ltrs capacity made out of FRP (made with Bisphenol resins) having port hole on lid for pouring chemical, water inlet connection, overflow and drain with valve, outlet connection with PP ball valve for transferring solution to chemical dosing tank of 100 Ltrs capacity made out of FRP (made with Bisphenol resins) having port hole on lid, inlet connection and tank lid duly mounted with agitator made of Stainless Steel -316 operated with single phase FHP electric motor for dissolution of chemical, dising pump shall be complete with inlet /outlet check valves, strainer cum foot valve and tubing for suction/delivery injection line including fittings etc, complete all as specified and as directed

Disconnecting, taking out and removing old existing unserviceable underground, LT cable of any description and in any position complete including taking down protection pipe,PCC Cover/Bricks etc all as specified and directed for the following sizes:

16 Sqmm x 4 core any make

25 Sqmm x 4 core any make

35 Sqmm x 3.5 core any make

50 Sqmm x 3.5 core any make

70 Sqmm x 3.5 core any make

Supply, laying, jointing and testing XLPE cable, PVC insulated, armoured, heavy duty, aluminum conductor cable 1100 volts grade of any description and any make laid in trenches/ducts, floors, fixed to walls etc. complete all as specified and directed for the following sizes :-

16 Sqmm x 4 core

25 Sqmm x 4 core

35 Sqmm x 4 core

50 Sqmm x 3.5 core

70 Sqmm x 3.5 core

Excavation in trenches in soft & loose soil not exceeding 1.5 metre deep and not exceeding 1.5 mtr width and getting out soil including forming bottom surface to required slope / gradient for laying cables/ pipes etc. all as specified and directed including removing cable protection PCC covers/ bricks & stacking serviceable covers / bricks for reuse and disposal of unserviceable covers within 50 m all as specified and directed. Note : Excavation shall be made carefully in order to avoid damage of existing cables/pipes and protection covers.

Returning, filling in including spreading, leveling, watering and well ramming in layers of 25 cm thick after the cables etc. are laid, jointed & tested complete all as specified and directed

Removal of surplus excavated soil exc. 50 mtr but n. exc. 250 mtr distance and depositing where directed at a level not exceeding 1.5 M above the starting point etc complete all as directed.

Material and labour for river washed and screened, dry sand for cushioning of cable in trenches for cable protection including spreading, leveling and hand punning complete all as specified in SSR Part-I and as directed. Note :- Only compacted thickness of sand will be measured and paid separately.

Supplying & Laying Sub Class `B’ bricks old size with axis of the bricks perpendicular to the axis of the cable as in cable protection all as specified and directed.

Material and labour for Horizontal directional drilling (HDD) is a streeable trenchless method of Laying (installing) underground cables in a shallow arc along a 40mm/50mm bore path by using a surface-launched drilling rig, with minimal impact on the sorrounding area complete all as specified and as directed by Engr-in-charge.

M&L for GI pipe ,light grade 40mm dia for road crossing of cable for cable protection laid in trenches or above ground surface, complete all as specified and directed.

Demolition for cement concrete/road in ground floor and paving n. exc 15 cm thickness below or above ground level including removal of rubbish to a distance exc 1.50 Km and n.exc 5.00 Km etc complete all as specified and directed.

M&L PCC 1:2:4, type B1 (using 20 mm graded granite stone aggregate) as in coping for steel pole including necessary formwork complete all as specified.

M&L for PCC 1:2:4 type B2 (using 40 mm graded stone aggregate) for road/Hard standing cutting complete all as specified and as directed.

Supply and fixing of display board of outer size 4.1X1.0 mtr made out of stainless steel of thickness 2 mm at square pipe 8X8 cm with back support of 40X5 mm stainless steel plate fitted at 3 fet interval of board backside including writing name of installation and unit as directed with reflecting tape of any colour as directed alongwith legs of size 8X8 cm square pipe upto the height of 14 feet from ground with foundation with stand 26 km/hr air velocity alongwith 02 nos of spot light at suitable place as directed with point wiring as directed.

M/s Naresh Kalia (BID ID -3331095)