SPECIAL REPAIR WORKS TO BLDG NO T-42 AT 6121 (I) FD WKSP COY,T-74 OF 9 BATTALION AT JKR, DINING HALL AT GE KARGIL, CEMENTED PATHWAY IN 13 MFVH UNIT UNDER GE KARGIL.

Amount

Dismantling of floor hearth and wall tiling including cement mortar bedding (but not backing) and removing serviceable like to store and rubbish off the premises, complete all as specified and directed by Engr-in-Charge.

Dismantling of plain or corrugated steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed by Engr-in-Charge.

Demolition of brick or stone/concrete blcok/stone boulder masonry built in cement mortar including all quions, arches, pillars etc., but excluding ashlar facings, dressed stone works and precast cement articles, complete all as specified and directed by Engineer-in-charge.

Dismantling of timber scantling of any description, 40 sqcm and over in section, in any position as in unframed work, complete all as specified and directed by Engr-in-Charge.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/ slabs /blankets, any thickness, including cover fillets, complete all as specified and directed by Engr-in-Charge.

Dismantling of timber scantling fillets, rails, posts rafters, purlins etc under 40 Sqcm, in any position as in unframed work, complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for cement concrete complete all as specified.

Demolition of PCC (un-reinforced) in ground floors & pavings n.exc 15 CM thickness below or above ground level, complete all as specified and directed by Engr-in-Charge.

Taking down chowkats or frame shutter(without taking off shutter from the frame) not exceeding 1.5 Sqm each, complete all as specified and directed by Engr-in-Charge.

Taking down chowkats or frame shutter(without taking off shutter from the frame) but exc 1.5 sqm but n.exc 4 Sqm each, complete all as specified and directed by Engr-in-Charge.

Taking up or down steel water tubing 15 mm bore of pipe and connections, including cleaning for reuse if found serviceable or removal to store , complete all as specified and directed by Engr-in-Charge.

Taking up or down steel water tubing 20 mm bore of pipe and connections, including cleaning for reuse if found serviceable or removal to store, complete all as specified and directed by Engr-in-Charge.

M&L for Precast cement concrete, type-C-1, block masonary with solid blocks, 1:3:6 (using 20mm graded crushed stone aggregate) exc. 10cm in width and setting in cement mortar (1:6), complete all as specified and directed by Engr-in-Charge.

M&L for 75mm thick, plain cement concrete ,1:3:6, type C-2, (using 40mm graded crushed stone aggregate) as in sub base flooring, surface finished even, complete all as specified and directed by Engr-in-Charge.

M & L for 75mm thick, plain cement concrete, type D-2, 1:4:8, (using 40mm graded stone aggregate) as in sub base flooring, surface finished even and rough to receive floor topping, complete all as specified and directed by Engr-in-Charge.

M & L for 70mm thick, plain cement concrete, type B-1, 1:2:4, (using 20mm graded stone aggregate) as in fooring, surface finished even and rough to receive floor topping, complete all as specified and directed by Engr-in-Charge.

M&L for chequered cement concrete tiles 20x20x25mm thick, with grey cement and no pigments, set, jointed and pointed in neat cement slurry in floors over and including 15 mm thick screed bed in cement mortar in (1:4), complete all as specified and directed by Engr-in-Charge.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4, finished even and smooth surface without using extra cement, complete all as specified and directed by Engr-in-Charge.

Rendering 15 mm thick in cement mortar 1:6, on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed by Engr-in-Charge.

M&L for Non-skid coloured ceramic tiles, 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11sqm, in floors etc, set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles laid over and including 15 mm thick screed bed in CM 1:4, complete all as specified and directed by Engr-in-Charge.

M&L for Non-skid coloured ceramic tiles, 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm, in floors etc, set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles laid over including 15 mm thick screed bead in CM 1:6, complete all as specified and directed by Engr-in-Charge.

Non-skid coloured ceramic tiles, 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38sqm, in floors etc, set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles, complete all as specified and directed by Engr-in-Charge.

M & L for Glazed ceramic coloured tiles of size 300x200x7 mm thick on vertical surface such as in dado/skirting/risers to steps etc set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles laid over and including 10 mm thick rendering in CM (1:4), complete all as specified and directed by Engr-in-Charge.

M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing inn white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

S&F 0.50mm thick, galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach and washers, in roofs, walls etc, with grade of zinc coating 275, complete all as specified and directed by Engr-in-Charge..

S & F 2 mm thick, Fibre glass reinforced translucent corrugated sheeting with two corrugations side laps fixed with L-type or J-type or cranked hook bolts in lieu of screews as in roof and walls, complete all as specified and directed by Engr-in-Charge.

M&L for 2nd Class soft wood moulding as in cornicses, picture, rails and the like n.exc.6 sq cm., complete all as specified and directed by Engr-in-Charge

M&L for Plain fillets of second class soft wood (KAIL) sectional area exceeding 13 Sqcm and not exceeding 25 Sqcm, square, rectangular or triangular in section, clean sawn, secured with nails, complete all as specified and directed by Engr-in-Charge.

S & F 12mm thick, prelaminated particle board, interior grade, prelaminated one side with decorative lamination and other side balancing white lamination fixed with nails to timber frame work, complete all as specified and directed by Engr-in-Charge.

S&F 9 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with nails to timber frame work complete, all as specified and directed by Engr-in-Charge

S&F Second class soft wood (KAIL), plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed by Engr-in-Charge.

Second class soft wood (KAIL) plain, framed, panelled shutters (any number of panels), 35 mm thick with panels of 9mm ply BWP commercial type or 12 mm thich of veneered particle board with commercial veneering both faces as in doors, complete all as specified and directed by Engr-in-Charge.

S&F 30 mm thick 2nd calss soft wood skelton shutters divided into squares with plain Sqm chamfred or rounded mitred and rebated sash bars for windows/ventilator any numbers size of stiles and rails as specified in SSR Part-I section -08 clause 8.24 (a), complete all as specified and directed by Engr-in-Charge.

S&F stainless steel curtain rods with ring 8 nos per RM with side wall brackets and knobs complete all as specified and directed.

S & F 4mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.50 Sqm in each pane, complete all as specified and directed by Engr-in-Charge.

Supply and fixing 100 mm long mild steel butt hinges medium weight cold rolled , complete all as specified and directed by Engr-in-Charge.

S & F 200 mm long Aluminium anodised, barrel tower bolts of extruded section, complete all as specified and directed by Engr-in-Charge.

S&F 150mm long, mild steel handles cast type , fitted, complete all as specified and directed by Engr-in-Charge.

S&F Mild steel sliding door bolt 300 mm long plate type slove enamelled blak wioth bright bolt not less than 12 mm dia with and incl a minimum of 6 bolt and nut four on bolt plate and two on staple plate and fixed, complete all as specified and directed by Engr-in-Charge.

Prepation of new plastered or unplastered surfaces of walls and applying two coats of Cement base paint , complete all as specified and directed by Engr-in-Charge.

Preparation of old plastered surfaces of walls and applying two coats of oil bound distemper with approved colour and shade, complete all as specified and directed by Engr-in-Charge.

M&L for preparing previously untreated wood and wood based material of any description over 10cm width/girth and applying two coats of synthetic enamel paint over one coat of pink primer including preparation of surface.

Preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint, complete all as specified and directed by Engr-in-Charge.

Supply and fixing 15mm dia GI tube medium grade galvanised, with all fitting and fixed to walls and ceilings or laid in floors, complete all as specified and directed by Engr-in-Charge.

Supply and fixing 20mm dia GI tube medium grade galvanised, with all fitting and fixed complete laid in trenches, complete all as specified and directed by Engr-in-Charge.

S&F grating doom 125mm dia with or without waste hole of PTMT (Minimum weight 40 gms), complete all as specified and directed by Engr-in-Charge.

S&F sinks with drainage board made of stainless steel 01mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x160mm, complete all as specified and directed by Engr-in-Charge.

Supply and fixed in repairs Vitreous china wash basin, white, flat back, size 550X400 mm including waste pipe, bracket and cutting for and pinning in ends of brackets or errecting stand but excluding taps, chain and plug, complete all as specified and directed by Engr-in-Charge.

S&F in repairs vitreous china squatting pan, Orissa Pattern size 580mm x 440mm white with integral foot rest and ‘P’ or ‘S’ trap , front or back inlet but excluding flushing cistern and flush pipe including placing in position and embedded lean/lime concrete bedding,complete all as directed by Engr-in-charge.

S&F PVC flushing cistern valveless syphonic action type flushing cistern low level 10 Ltrs white with inlet ball valve float and handle incl bracket.

Supply and fixing Bib taps,15 mm bore,fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for brass ferrule, complete all as specified and directed by Engr-in-Charge.

Supply and fixing fancy type stop cock 15 mm bore chromium plated with long shank and cup (concealed type), complete all as specified and directed by Engr-in-Charge

S&F pillar tap 15 mm bore cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed and fly screwed for iron pipe and fixed fancy type.

Taking down carefully copper or aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches ceiling roses, pendants, sockets bulk, head fitting, tube light fitting by unscrewing carefully from boards etc and making good, distrubed surface of walls floors etc. , complete all as specified and directed by Engr-in-Charge..

Point wiring with multi-stranded copper conductor PVC insulated and unsheathed cable in PVC casing and capping, 1.5 Sqmm with all fittings/accessories and including 1.5 Sqmm PVC insulated copper earth wire connected to common earth including closed recessed wooden terminal Boxes of suitable size made of 2nd class hard wood for mounting switches, sockets etc with 3mm thick laminated sheet cover for one light point or bell/buzzer point controlled by one switch, complete all as specified and directed by Engr-in-Charge..

All as per Srl item No 1.56 here in before but for one 3 pin 5 Amps switch socket on same board.

All as per Srl item No 1.56 here in before but for one 3 pin socket outlet 5 Amps on independent board.

All as per Srl item No 1.56 here in before but using cable size 2.5 Sqmm for one 3 pin socket outlet 15 Amps on independent board.

S&F Switch piano 5 Amps, single pole one way flush type, complete all as specified and directed by Engr-in-Charge

S&F Switch socket combination 2 in 1, and 3 and 2 pin, 5 Amps Flush type, complete all as specified and directed by Engr-in-Charge.

S&F Switch socket combination 2 in 1, 5 and 15 Amps, Flush type, complete all as specified and directed by Engr-in-Charge.

S&F Lamp holder, insulated body with back plate suitable for batten fittings, complete all as specified and directed by Engr-in-Charge.

S&F Ceiling rose surface bakelite 65x50mm, two to three terminals, complete all as specified and directed by Engr-in-Charge.

Sheet metal enclosure for DB’s, single door single pole and neutral, 240V, 8 way with 200 Amp rated bus bar including blanking plates where required, complete all as specified and directed by the Engr-in-Charge.

Sheet metal enclosure for DB’s, single door single pole and neutral, 240V, 12 way with 200 Amp rated bus bar including blanking plates where required, complete all as specified and directed by the Engr-in-Charge.

S&F MCB single pole and neutral 32 amps, 240 volts , complete all as specified and directed by Eing-in-Charge.

S&F MCB single pole, 5 to 32 Amp , 240 volts , 10 KA complete all as specified and directed by Eing-in-Charge.

S&F rectangular block PVC of size 30x25x5 cm closed recessed complete all as specified and directed by Engr-in-Charge.

S & F surface and wall mounted LED 1x18/20 W extruded aluminium housing providing for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver complete all as specified and directed . Havells cat part no. ENDURALINEARNEOBS20WLED865SPCWH or equilent of approved make

Supply and Fixing LED 18 Watt tubelight fitting decorateive ultra slim square profile leinear with extruded polycarbonate environoment friendly , complete all as specified and directed by Engr-in-Charge. Make Havells Cat Part LHEXBTP7IN1W018 or equvilanat in Bajaj or Philips

Earthing complete with steel earth plate electrode 600mmx600mmx6mm thick buried directly in ground (earth plate not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level connecting to the galvanised iron earth wire 4.0mm dia by means of bolts, nuts, check nuts and washers of GI and steel earth wire including provision of concrete pit made from PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) in pit, angle iron 25x25x6mm frame work with precast RCC 1:2:4 type B-1 cover reinforced with 8mm dia TMT bars @ 150mm C/C both ways and 12mm dia MS fabricated handle, medium grade GI watering pipe 20mm bore with funnel, wire mesh and light grade GI protection pipe 15mm bore up to 7.5m length for drawing in earth lead wire, salt, charcoal, etc. including excavation and earth work in any type of soil, removal of surplus spoil to a distance not exc. 50m complete all as shown in electrical plate No.3 of MES Schedule 2009 (Pt-I) and connected to earth test point all as specified including testing on completion.

Supply and fixing LED bulb 9 Watt complete all as specified and directed.

Amount of Sch 'A' Part - II (Credit Schedule) Rs. 41942.00 (minus) as listed in Schedule of credit shall be deducted from total BOQ during AOC.

M/S M A ENTERPRISE

M/S LIAQAT ALI KHAN

M/S MOHD KHAN

JP AND CO.