JJMII -Meenagady

Amount

Design, Supply, Errection and commissioning of VT Pump sets to Krishnagiri WTP at Karapuzha Raw water Pump House

OD300242/2023-2024:Supply and erection of VT pump set with the following specification 1. Pump- Supply and Erecting testing and commissioning at site, 2 Nos of brand new vertical turbine pump set, with bronze impeller(LTB2),stainless steel pump shaft(SS 316),SS head shaft, stainless steel column (intermediate) shaft, water lubricated type, sleeve (SS410) column assembly, neck ring (bronze LTB2), sleeve(SS410), spider bush, Discharge head, strainers and all accessories complete conforming to relevant IS. The pump set shall be coupled with the motor suitable for the pump. The details of each pump set to be supplied are Make: KWA approved companies Capacity : b) Motor recommended (Vertical Hollow Shaft),c) Erection charges of the above pump and motor suitable in concrete foundation including erection of column assembly bowl assembly piping strainer etc, including non reversible rachet mechanism, first filling of bearing oil, bearing and shaft cooling piping The duty condition is 66 lps discharge and Total head - 103M, 120hp -2 nos

OD300312/2023-2024:Motor starter: 100 KW, Supplying a complete integrated soft starter panel capable of operating the motor having a protection level of IP 40 or more with integrated bypass contactor in the panel and motor protection relay having parameters as per IE rules, with a power control MCCB and line power cotactor, and the staring current shall be 2.5 to 3.5 times the normal full load current of motor with Ammeter, Voltmeter and phase indicators, Space heaters, floor mounting type and having insulation level of 1100V(for 440V supply) and 7.6KV for (3.3KV supply) and 14.2KV for (6.6KV Supply). the standared is to be IEC 60947-4-2

OD300883/2023-2024:Supplying and fixing Electromagnetic flow meter conforming to protection level IP-68 for flow sensor and IP-67 for transmitter and having an accuracy level of 0.5% with LED/LCD display unit suitable to measure the discharge of CW . The flow meter should have the housing ( flow sensor) to be made of SS 304/Carbon steel with anti-corrosive protection and inside liner to be made up of Hard Rubber/ Neoprene all confirming to drinking water standards. The flow meter should be coupled with HART for data acquisition and transfer with provision for wireless transfer through GSM. The manufacturers should have the calibration standards as per ISO 17025 and the product shall have sufficient warrantee position. Flow meter should be tested and calibrated at FCRI, Palakkad and test certificate should be produced. Flow meter should be calibrated with physical measurement at site after installation. A battery backup of min 24 hrs should be provided. For 250 mm Flow meter.

Design , Supply Errection and Commissioning of Clear water Pump sets from Krishnagiri WTP to Arivayal GLSR

OD300237/2023-2024:Design, Supply , erection and commissioning of pump set with the following specification, 1. Pump- Supply, erection, testing and commissioning of KWA pre-qualified reputed make Centrifugal pump sets with Bronze/SS impeller, SS shaft and CI pump casing with suitable type base plate with coupling, coupling guard foundation bolts & nuts etc. complete suitable for coupling the pump and motor above the base plate etc. complete including providing suitable concrete foundation including cost of cement sand and metal etc. complete. The duty condition is 30 lps discharge, Total head - 90 M, including all cost of conveyance , materials , all accessories etc complete .

OD300317/2023-2024:Motor starter: Supplying a complete integrated soft starter panel capable of operating the above motor having a protection level of IP 40 or more with integrated bypass contactor in the panel and motor protection relay having parameters as per IE rules, with a power control MCCB and line power contactor, and the starting current shall be 2.5 to 3.5 times the normal full load current of motor with Ammeter, Voltmeter and phase indicators, Space heaters, floor mounting type and having insulation level of 1100V(for 440V supply) and 7.6KV for 3.3KV supply and 14.2KV for 6.6KV Supply. The standard is to be IEC 60947-4-2, including all cost of labour , all accessories, conveyance etc complete.

OD300884/2023-2024:Supplying and fixing Electromagnetic flow meter conforming to protection level IP-68 for flow sensor and IP-67 for transmitter and having an accuracy level of 0.5% with LED/LCD display unit suitable to measure the discharge of CW . The flow meter should have the housing ( flow sensor) to be made of SS 304/Carbon steel with anti-corrosive protection and inside liner to be made up of Hard Rubber/ Neoprene all confirming to drinking water standards. The flow meter should be coupled with HART for data acquisition and transfer with provision for wireless transfer through GSM. The manufacturers should have the calibration standards as per ISO 17025 and the product shall have sufficient warrantee position. Flow meter should be tested and calibrated at FCRI, Palakkad and test certificate should be produced. Flow meter should be calibrated with physical measurement at site after installation. A battery backup of min 24 hrs should be provided. For 250 mm Flow meter.

SURAS AGENCIES

Bidder Name

SURAS AGENCIES

SARATH LAL T