PMABHIM

Construction of Village Health Clinic

Earth work excavation and depositing on bank with initial lead of 10m and initial lift of 3m in Loamy & Clayey Soils like BC Soils, Red Earth & Ordinary Gravelly Soils ( SS 20-B) including all operational incidental labour charges such as shoring, strutting, sheeting, planking and dewatering including cost of hire charges of T & P, labour charges etc., complete for finished item of work including seignerage charges excluding dewatering charges etc., complete for Foundation of Building.(APSS No. 308)

Sand filling in trenches, sides of foundations and basement with initial lead in layers not exceeding 15cm thick consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T&P etc., complete for finished item of work.

Plain Cement concrete (1:4:8) using 40 mm HBG Metal from approved quarry including cost and conveyance of allmaterials like Cement, Sand, coarse aggregate, water etc., to site (Hand Mixing), complete for finished item of work for Foundations and flooring bed (APSS No.402)(CSSR)

Design Mix Concrete M30 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for FOOTINGS

Design Mix Concrete M30 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for PEDASTALS

Design Mix Concrete M30 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for COLUMNS

Design Mix Concrete M30 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for Plinth Beam

Design Mix Concrete M30 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for LINTELS: Ground Floor

Design Mix Concrete M30 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for SUNSHADES:

Design Mix Concrete M30 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for Roof beams-

Design Mix Concrete M30 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for RCC SLABS 125mm thick:

Design Mix Concrete M30 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for RCC SLABS 100mm thick

Masonry work in CM (1:6) proportion (Cement : Screened sand) in superstructure with fly ash cement / lime solid blocks of size 290 mm x 225 mm x 140 mm from approved source having minimum crushing strength of 50 Kg/Sqcm. including cost and conveyance of all materials like cement, sand, bricks, water etc., to site, including sales & other taxes on all materials and such as labour charges, like mixing cement mortar, scaffolding charges, constructing masonry, lift charges, curing, overheads and contrctor profit etc., complete for finished item of work. (APSS No. 501 & 504) for For basement

Filling with Selected earth in trenches, sides of foundations and basement with initial lead in layers not exceeding 15cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to the work site and all operational, incidental, labour charges, seignorage charges, hire charges of T & P etc., complete for finished item of work. (APSS NO. 309 & 310)

Providing impervious coat over RCC roof slab to required slopes with CM (1:3) prop. 20mm thick (average) mixed with water proofing compound at 1Kg/bag of cement, laid over roof slab when it is green, finished smooth with a floating coat of neat cement and thread lining at regular intervals of 45cmx45cm including Cost and Conveyance of all materials complete for finished item of work (APSS No. 901 & 903).(CSSR)

Brick Masonry in CM (1:8) with Non-modular traditional bricks of size 23 x 11 x 7 cm for Superstructure including cost and conveyance of all materials, all labour charges, curing charges and scaffolding charges etc complete for finished item of work for Super structire

Reinforcement birck masonary walls of 11.5cm in CM (1:6) using 2nd bricks having a crushing strength of not less than 35.00Kg/cm2 and using two mild steel bargs of 6m dia in every third layer of brick masory, with free joints of the main block work including cost and conveyance of all materials and water from approved sources to work site and all operationsl, incidental labour charges such as scaffolding mixing mortor constructing masonary lift charges, curing including Overheads & Cotractors Profit . complete but execluding the cost of steel and its fabrication charges for finished item of work as per SS 509 for super structure

Supply and fixing of MediumTeak wood Door Double shutter fully pannlled door of size 1.20 x 2.10mt with frame made of well seasoned teak wood scantlings of size 100 x 75mm mm and shutter made of side rails 125mm X38, top rail 125mmX38mm, bottom rail 125mmX38mm and intermediate rails of 125 x 38 mm and panels - 8 no's are of 25mm thick as per approved design with fixtures of 6 nos of 9" ' z" holdfasts, 250 mm long MS power coated aldrop-1 no,250mm long brass latch,125mm long butt hinges 8No's, Door stoppers-2 no, MS Power coated 150 mm long Tower bolts - 2no's Poer coated, MS power coated fancy handles 150mm long 2no's, with necessary screws complete including cost and conveyance of all materials and labour charges etc. complete as per specifications (APSS NO.1001 & 1002 (CSSR)

Supply and fixing of MediumTeak wood Door Double shutter fully pannlled door of size 1.00 x 2.10mt with frame made of well seasoned teak wood scantlings of size 100 x 75mm mm and shutter made of side rails 125mm X38, top rail 125mmX38mm, bottom rail 125mmX38mm and intermediate rails of 125 x 38 mm and panels - 8 no's are of 25mm thick as per approved design with fixtures of 6 nos of 9" ' z" holdfasts, 250 mm long MS power coated aldrop-1 no,250mm long brass latch,125mm long butt hinges 8No's, Door stoppers-2 no, MS Power coated 150 mm long Tower bolts - 2no's Poer coated, MS power coated fancy handles 150mm long 2no's, with necessary screws complete including cost and conveyance of all materials and labour charges etc. complete as per specifications (APSS NO.1001 & 1002 (CSSR)

Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of size with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebat of 32MM. Door Frame section of 63.5x100 MM .The two Vertical members are to be joined together with the horizontal member using 8x75 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member.

Providing and fixing 28 -30 MM thick solid Wood Polymer Composite(WPC) single extruded Door Shutter with 3MM top and bottom rigid layer with an overall density of 750kg/Cum. It will be fixed to the frame using 3 inch /4 inch hinges. A minimum of 4 hinges will be required for fixing the door with the frame

Supplying and fixing of MS Iron Window grills using MS angles of 25 x 25 x 5 mm size for outer frame, including cost and conveyance of all materials ,fabrication charges and all other labour charges etc., complete.

Supplying and fixing of Stainless steel hand railing as per approved drawing with top rail of 64mm dia (outer) 2mm thick pipe, vertical balusters of 50mm dia 2mm thick at 600mm c/c spacing (7 Nos)and 3 nos 25mm dia (outer) 1.6mm thick stainless steel pipes below top rail with equal spacings and 50mm wide 8mm thick SS plate for fixing vertical balusters at 600mm centre with 100x100mm stainless steel base plate to be fixed to the steps with Anchor fasteners. The rate should include providing and using bonding agent, drilling of 25mm holes of fixing railing , polishing of all nos of railing thouroughly and also including cost and conveyance of all materials, electrodes, welding charges, cost of all consumables, labour charges such as for fabrication of SS pipes, buffing, polishing etc., complete for finished item of work.

Providing and fixing factory-made uPVC any colour sliding glazed window upto 1.50 m in height dimensioncomprising of uPVC multi- chamberedframe with in-built roller trackand sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from rollforming process of required length (shape & size according to uPVCprofile), appropriate dimension of uPVC extruded glazing beads anduPVC extruded interlocks, EPDM gasket/TPV, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylonrollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mmsize for fixing frame to finished wall and necessary stainless steel screwsetc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage ofwater etc. After fixing frame the gap between frame and adjacent finishedwall shall be filled with weather proof silicon sealent over backer rod ofrequired size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge inclusive of cost of Single / double glass panes, wire mesh and silicon sealent . Note: For uPVC frame and sash extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be acceptedbut no extra payment on this account shall be made.

Ornamental Plastering with CM (1:3), 12 mm thick for exposed surfaces of R.C.C. works including cost and conveyance of all materials, all labour charges, curing charges and scaffolding charges etc complete for finished item of work for Ground Floor:

Plastering with CM 2 coats, 12 mm thick, base coat in CM (1:6), 8 mm thick and top coat in CM (1:4), 4mm thick with Dubara sponze finishing.Internal walls for Ground Floor

Plastering with CM 2 coats, 20mm thick, base coat in CM (1:6), 16mm thick and top coat in CM (1:4), 4mm thick with sponze finishing including cost and conveyance of all materials and all labour charges etc., complete for walls for Ground Floor:

Painting to New Wood work with two coats of ready mixed synthetic enamel paint first quality all shades over a base coat of wood primer making three coats in all to give an even shade after thouroughly brushing the surface to remove all remains of loose powderedd materials, including c/c of all materials, site and other taxes, all operational, incidental and labour charges etc., complete for finished item of work in all flooring for external walls. (APSS No.1201, 1207 & 1212)(CSSR) for 1 sqm

Providing and applying synthetic plaster putty or plaster of paris putty or lime punning of average 1 to 2 mm thickness over plastered surface to prepare the surface even and smooth after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, Sand the surface, clean & wipe off loose dust, applying knife paste filler by putty knife/ muslin pad, air dry for 2 - 3 hrs, sand with 180 and 320 No. emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work for internal walls.

Painting to new walls and ceiling in two coats with Plastic Emulsion Paints Asian/ Berger/ Nerolac or equivelent and shaded over Priming Coat with Cement Primer water base interior Gr -1 or equavalent quality to give an even shade after thoroughly brushing the surface to remove all loose powdered materials including cost and conveyance of all materials and water to site, sales & other taxes, all operational, incidental and labour charges such as cleaning the surface, painting, curing etc., complete for finished item of work for internal walls. (APSS No.901 & 908)

Painting to New walls with two coats of plastic Emulsion Paints Asian / berger/ Nerolac or equavalent quality of approved shade over base coat of cement primer grade 2 making three coats in all to give an even shade after thoroughly brushing the surface to remove all loose powdered materials, including cost and conveyance of all materials, including cost and conveyance of all materials, cost of brushes, water to site, etc., sales & other taxes, all operational, incidental and labour charges such as scaffolding charges, lift charges, curing etc., complete for finished item of work in all floors for External Walls.(APSS No. 912)

Flooring with non-skid Double charged / multi charged stain free full body porcelain vitrified tiles with double layer pigment of size 600 x 600 mm and thickness between 8-10 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs with borders and design as per the approved flooring pattern as directed by the Engineer-In -Charge, laying tiles using spacers of 2mm thick, set over a base coat of CM (1:8) prop. 12mm thick using screened sand over CC bed already laid or RCC roof slab , including neat cement slurry of honey like consistancy spread @ 3.3 kgs per sqm. and jointed neately with white cement paste to full depth mixed with pigment of matching shade including cost and conveyance of all materials like cement, sand, water, tiles, white cement etc., to site (excluding cost of C.C. bed) including cost of base coat and all labour charges for mixing of cement mortar, laying tiles to required slope as directed by the Engineer- in-charge etc.,and overheads & contractors profit complete for finished item of work. (APSS No.701 & 707.

Providing skirting 10 cm height with Double charged / multi charged stain free full body porcelain vitrified tiles with double layer pigment of Size 600 x 600 mm and thickness between 8-10 mm of any colour and finish in all shades and designs, length equal to flooring tiles, flushed to wall surface to set over base coat of CM(1:5) 12 mm thick using screened sand with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointing with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc.,and overheads & contractors profit complete for finished item of work.(APSS No.701 &707)

Flooring with non-skid red or white full body Ceramic floor tiles of size 300 mm x 300 mm and thickness between 7-8 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs as approved by Engineer-in-charge, set over base coat of cement mortar (1:8), 12mm thick using screened sand over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 Kgs per sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, screened sand , water and tiles etc., and overheads & contractors profit complete for finished item of work. (APSS No.701 & 707)

Dadooing to walls with glazed red or white full body ceramic wall tiles of size 200 x 300 mm and thickness between 6-8 mm 1st quality, set over base coat of CM (1:3) 12 mm thick with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointed with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc., complete for finished item of work.

Supplying, fitting and placing HYSD bar reinforcement (Fe 500 / Fe 500 D grade as per IS 1786-1979) of different diameters for RCC works including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying etc., and overheads & contractors profit complete for finished item of work.( APSS No.126) for Ground Floor:

Supply and installation of Double grooved and precoated extruded mineral (cement) roof tiles of size 420 mmx330 mm of corrugated profile tiles with variable overlapping for coverage of 1-1.2 per tile with European standards BEEN 490:2004

Construction of Septic Tank

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per Technical Specification 305 MORD / 304 MORTH

Plain Cement Concrete corresponding to M7.5 grade as per IS 456 equivalent to (1:4:8) proportion nominal mix (cement: fine aggregate: Coarse aggregate) using 40mm size Hard Blasted Granite (IS383, 1970) metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, including seigniorage charges, sales & other taxes on all materials, all operational, incidental, and labour charges such as mixing, laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete for finished item of work for Foundations (APSS No. 402)

Design Mix Concrete M30 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for Raft

Brick masonry in CM (1:6) with bricks of traditional size 23 x 11 x 7 cm 2nd class including cost and conveyance of all materials and all labour charges etc., complete for finished item of work for below Basement

Providing Impervious coat to exposed RCC roof slab surface with CM(1:3), 20mm thick with 1kg of water proof compound per bag of cement laid over roof when it is green including cost and conveyance of all materials all operational, incidental and labour charges for mixing mortar, laying, rendering smooth and thread lining, curing, rounding off junctions of wall and slab etc., complete for finished item of work.

Reinforced Cement Concrete M-30 Design mix (Cement: Fine aggregates: Coarse aggregates) corresponding Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like Cement, fine aggregate( Sand), coarse aggregate, water etc to site and including sales and other taxes on all materials including all operational, incidental and labour charges such as machine mixing, laying concrete, curing etc complete but excluding cost of steel and its fabrication charges for finished item of work, but including centering, shuttering for finished item of work Slab of 100mm thick

Supplying and fixing of 110mm dia SWR/ PVC pipes (as per ISI standards) 4 Kg/Sq.cm. Prince/sudhakar or any ISI brand and fixing all special such as plain bends, off sets, door bends, single junctions, double junctions as per site requirement, fixing with PVC clamps if necessary with required number of Bombay nails including cost and conveyance of all materials to site, labour charges etc.complete for finished item of work at all floor levels. (APSS No. 1302 1319 & 1326)

Providing high yield strength deformed (HYSD) steel bars (Fe 500 grade as per IS 1786-1985) of 8mm to 40mm diameters, cutting, bending, to required sizes and shapes placing in position with cover blocks of approved size and binding wire of 20SWG, forming grills for reinforcement work as per approved designs and drawings including cost and conveyance of bars from approved sources to site of work, including cost and conveyance of binding wire, cover blocks and all operational, incidental, and labour charges such as cutting, bending, placing in position, tying etc., and sales & other taxes,on cost of all materials complete for finished item of work

Electrical Items

Supply and fixing of 25mm dia 1.8mm thick P.V.C. pipe (ISI Mark) concealed in wall with all required accessories including masonary work and labour charges etc., complete.

Supply and fixing of 25mm dia 2.2mm thick P.V.C. pipe (ISI Mark) concealed in Roof Slabs with all required accessories including masonary work and labour charges etc., complete..

Wiring with 2 runs of 14/0.3mm (1.0 Sq.mm) Fire Retardant (FR) P.V.C. insulated flexible copper cable (ISI MARK) in existing pipe with 6A switch, Ceiling rose and 3mm tick hylam sheet covering to switch control box including all labour charges etc., complete for light, bell, fan and exhaust fan points in Non-Residential buildings. .

Supply and fixing of 6A 3 pin wall plug socket with a 6A switch control on a common switch board with earth continuity including wire leads, earth connections along with all labour charges etc., complete..

Supply and fixing of 16A 3pin flush type switch socket combined (2 in 1) duly recessed in wall with wooden deep box of 6"x8"x21/2" size covered with hylam sheet including earth connections and all labour charges etc., complete.

Supply and fixing SPN Distribution board with IP-20 protection suitable for single phase Earth Leakage Circute Braker (ELCB) / Residual Current Circute Braker (RCCB) / Double Pole (DP) Isolator as incomer and 10kA SP MCBs as out going including internal connections and labour charges for surface / flush mounting etc., complete.

Supply and run of 1 of 14 /0.3mm (1.0 Sq.mm) FR P.V.C. insulated flexible copper cable in existing pipe for earth continuity including all labour charges etc., complete.

Supply and run of 2 of 36/0.3mm (2.5 Sq.mm) F.R. P.V.C. insulated flexible copper cable in existing pipe for mains including all labour charges etc., complete.

Supply and run of 2 of 56/0.3mm (4 Sq.mm) F.R. P.V.C. insulated flexible copper cable in existing pipe for mains including all labour charges etc., complete.

Providing independent earthing by excavating a trench to a depth of 2.1M in all soils, as per size specified in the Data, using 40mm dia. 'B' class GI pipe of 2.5 Mtrs Length with necessary accessories with hume pipe ring duly providing staggered holes including filling with equal proportion of Salt and Charcoal in layers and all labour charges etc., complete for small quarters.

Supply and fixing of batten holder / slanting holder in lieu of ceiling rose of light point complete with all connections and all labour charges with 40W bulb (for new installation).

Supply and fixing of 20-24W, not less than 1100mm length LED batten light with extruded aluminum housing and polycarbonate cover, input voltage AC 220 - 260 Volts, with high power LEDs, having System Efficacy of >=90 lumens/watt , PF>0.9, Surge protection: 2KV, THD<15%, with inbuilt driver and frosted cover CCT: 3000K - 5700K, minimum CRI>70, etc., complete with earth connection and not less than two years warranty. Makes: Surya /C&S/ Fortune Arrt / Syska / Enrich / Stanjo / Polycab/ Ib LED/ Opple/ Luker/ Orbit/ Trinic/Lumens/ GLO LED / Vimal /Benlo /Goldwyn /Sturlite /AJUSS/Orient b) LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG / EVERLIGHT.

Supply and fixing of 48" (1200mm) Sweep 5 Star rated Ceiling Fan without Regulator with all standard accessories of makes Makes : Crompton HS Decora / Bajaj Regalstar / Havells Fusion 50 / Orient Summer Crown / Usha technix decorative including transportation and giving connections with twin core wire etc., complete.

Supply and errecting stepped type regulator for ceiling fans 900/1200/1400 sweep complete errected on existing board

Water Supply and Sanitary

Providing & Placing on Terrace (at all floor levels) polyethylene water storage tank with Double layer approved brand & manufacture with cover and suitable locking arrangement & making necessary holes for inlet & outlets and over flow pipes but without fittings & base support for tanks including cost of conveyance of all materials and labor charges, complete for finished item of work. -

Providing 110 mm Dia ISI marked PVC down water take pipes with socket, 2.5mm thick 4.0 kg/sq.cm pressure of ISI marked including cost of necessary PVC Bends, shoes, iron/ PVC clamps and all other accessories and fixing in position including cost and conveyance of all materials, operational & incidental charges including all labour charges for fixing at site etc., for finished item of work.

Providing 75 mm Dia ISI marked PVC down water take pipes with socket, 2.5mm thick 4.0 kg/sq.cm pressure of ISI marked including cost of necessary PVC Bends, shoes, iron/ PVC clamps and all other accessories and fixing in position including cost and conveyance of all materials, operational & incidental charges including all labour charges for fixing at site etc., for finished item of work.

Supply & fixing of tested NP bib taps at all levels of 12.70mm dia of Indian make first quality ( N.P bib tap indian make 400 g ) Long body including cost & conveyance of all materials, labour charges for finished item of work complete for all floors

Supply & fixing white glazed European water closet with variety as approved by Engineer-in-charge ,P" orS" trap with 4" CI outlet pipe of approved make,plastic seat and lid for EWC and rubber buffers as per ISI 2548 1963 with and 10 lits capacity PVC slimline low level flush tank of approved make with internal components and fixed with wooden gutties with required size nails,32mm dia short CP bend,12mm PVC Connections with brass union nuts and 12.70 mm (1/2") NP stop cock heavy duty (300 grams) complete including cost and conveyance of all materials to site,for finished item of work for all floors.

Supplying & Fixing Indian make Flat Back Wash Hand Basin 1st quality conforming to IS:2556-Part-4:1972 with waste fittings like rubber plug, chain,32 mm nominal size C.P. Fitting with parallel pipe thread conforming to IS:2963-1979 and fitted with 15 mm nominal bore Chromium Plated Pillar including wooden block: 550 x 400 mm - Single C.P. Pillar cock.

Supply & fixing bib cock cum health faucet with 1 m long flexible tube and wall hook of Jaquar make queen series with 7 years warranty Chrome plated

Providing & fixing GM gate / ball valve of 32 mm dia as per IS -778 Class - I, Indian make heavy type, including cost & conveyance of all material to work spot and all labour charges including fixing in position for finished item of work and all taxes.

4" (101.6 mm ) multi floor trap with Jali- UPVC/SWR Pipe fittings

4" (101.6 mm ) Nahany Trap ( Without Jali with inlet)UPVC/SWR Pipe fittings Each

Supply & fixing of 110 mm dia - Vent Cowl - UPVC/SWR Pipe fittings (Prince/ Sudhakar/ Kisan/Supreme or any ISI Brand) including cost and conveyance of all materials to site, all labour charges complete for finished item of work

Supplying & fixing stainless steel sink size 20" x18" x 8 "(508x457.2x203.2mm) 1 mm thick with accessories

Supply and Fixing of Premium make CPVC Pipes and Fittings to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper Tube Sizes 1/2" ton 2" SDR 11 and SDR 13.5 pipes are made from idential CPVC compounds having the same physicalProperties for Hot and Cold Water (IS 15778:2007) 15.90mm dia OD Pipe

Supply and Fixing of Premium make CPVC Pipes and Fittings to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper Tube Sizes 1/2" ton 2" SDR 11 and SDR 13.5 pipes are made from idential CPVC compounds having the same physicalProperties for Hot and Cold Water (IS 15778:2007) 22.2mm dia OD Pipe

Supply and Fixing of Premium make CPVC Pipes and Fittings to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper Tube Sizes 1/2" ton 2" SDR 11 and SDR 13.5 pipes are made from idential CPVC compounds having the same physicalProperties for Hot and Cold Water (IS 15778:2007) 28.60mm dia ODpipe

Drilling of Bore well

Drilling of Bore well by down the hole hammer drilling to a finished dia of 112/165 mm dia in all formations suitable for down the hole hammer drilling such as medium hard rock formation to hard rock formation, all consolidated formation etc. and drilling in over burden to dia not less than 200 mm etc and reaming the bore well to suit insertion of suitable casing pipe etc., including insertion of casing pipe with couplings, caps any other relevant materials upto required depth as directed by the department including transportation of drilling rigs and supporting vehicle and including bore development (Flushing of Bore Well at an average pressure of 150 PSI) conducting yield test, consumables charges, Crew charges required in fixation of pipe assembly completely done to the satisfaction of the department and including all labour charges but excluding all taxes, the cost of casing pipe, couplings, cap etc., The entire work should be carried out as per IS -2800 Part I & II 1979 and amended from time to time.

Cost and supply of 140mm dia UPVC calss-III pipe including all charges.

Cost and supply of 180mm dia UPVC calss-III pipe including all charges.

Sloting charges for 140mm dia UPVC calss-III pipe including all charges.

Geological survey for selection of site for hand pump by the Geologist

Supply and Transportation of 1.Hp, 5star rated submersible motor pumpset, confirming to IS 8034 and motor confirming to IS 9283 with waterproof winding, pump shall be suitable for various delivery head and discharge with stainless steel shaft motor suitable for working on 240V ± 10%, single phase 50 Hz AC supply, etc complete for 4" Bore well. Makes: As per list of recommended brands as category I. Makes: Kirloskar / Crompton / CRI / KSB / Texmo ELEC-5.4.2

Construction of Compound wall

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per Technical Specification 305 MORD / 304 MORTH

Sand filling in foundation / basement from approved Quarry / available sources including all operational, incidenal, labour charges, Hire Charges of T&P etc., complete (excluding rock) in trenches, sides of foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and cost and conveyance of water to site and all operational, incidental, labour charges, , sales and other taxes etc, hire charges of T & P etc., complete for finished item of work. (APSS NO. 309 & 310) for finished item of work

Plain Cement Concrete corresponding to M7.5 grade as per IS 456 equivalent to (1:4:8) proportion nominal mix (cement: fine aggregate: Coarse aggregate) using 40mm size Hard Blasted Granite (IS383, 1970) metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, including seigniorage charges, sales & other taxes on all materials, all operational, incidental, and labour charges such as mixing, laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete for finished item of work for Foundations (APSS No. 402)

Masonry work in CM (1:6) proportion (Cement : Screened sand) in superstructure with fly ash cement / lime solid blocks of size 290 mm x 225 mm x 140 mm from approved source having minimum crushing strength of 50 Kg/Sqcm. including cost and conveyance of all materials like cement, sand, bricks, water etc., to site, including sales & other taxes on all materials and such as labour charges, like mixing cement mortar, scaffolding charges, constructing masonry, lift charges, curing, overheads and contrctor profit etc., complete for finished item of work. (APSS No. 501 & 504) for For basement

Design Mix Concrete M20 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for FOOTINGS

Design Mix Concrete M20 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for PEDASTALS

Design Mix Concrete M20 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for COLUMNS

Design Mix Concrete M20 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for Plinth Beam

Brick Masonry in CM (1:8) with Non-modular traditional bricks of size 23 x 11 x 7 cm for Superstructure including cost and conveyance of all materials, all labour charges, curing charges and scaffolding charges etc complete for finished item of work

Supplying and fixing of MS Iron Window grills using MS angles of 25 x 25 x 5 mm size for outer frame, including cost and conveyance of all materials ,fabrication charges and all other labour charges etc., complete.

Plastering with CM 2 coats, 12 mm thick, base coat in CM (1:6), 8 mm thick and top coat in CM (1:4), 4mm thick with Dubara sponze finishing.Internal walls

Painting to New walls with two coats of plastic Emulsion Paints Asian / berger/ Nerolac or equavalent quality of approved shade over base coat of cement primer grade 2 making three coats in all to give an even shade after thoroughly brushing the surface to remove all loose powdered materials, including cost and conveyance of all materials, including cost and conveyance of all materials, cost of brushes, water to site, etc., sales & other taxes, all operational, incidental and labour charges such as scaffolding charges, lift charges, curing etc., complete for finished item of work in all floors for External Walls.(APSS No. 912)

Supplying, fitting and placing HYSD bar reinforcement (Fe 500 / Fe 500 D grade as per IS 1786-1979) of different diameters for RCC works including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying etc., and overheads & contractors profit complete for finished item of work.( APSS No.126) for Ground Floor:

(No.of items 92) only

Sand filling in trenches, sides of foundations and basement with initial lead in layers not exceeding 15cm thick consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T&P etc., complete for finished item of work.

Plain Cement concrete (1:4:8) using 40 mm HBG Metal from approved quarry including cost and conveyance of allmaterials like Cement, Sand, coarse aggregate, water etc., to site (Hand Mixing), complete for finished item of work for Foundations and flooring bed (APSS No.402)(CSSR)

Design Mix Concrete M30 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for COLUMNS

Design Mix Concrete M30 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for LINTELS: Ground Floor

Design Mix Concrete M30 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for SUNSHADES:

Design Mix Concrete M30 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for Roof beams-

Design Mix Concrete M30 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for RCC SLABS 125mm thick:

Design Mix Concrete M30 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for RCC SLABS 100mm thick

Masonry work in CM (1:6) proportion (Cement : Screened sand) in superstructure with fly ash cement / lime solid blocks of size 290 mm x 225 mm x 140 mm from approved source having minimum crushing strength of 50 Kg/Sqcm. including cost and conveyance of all materials like cement, sand, bricks, water etc., to site, including sales & other taxes on all materials and such as labour charges, like mixing cement mortar, scaffolding charges, constructing masonry, lift charges, curing, overheads and contrctor profit etc., complete for finished item of work. (APSS No. 501 & 504) for For basement

Providing impervious coat over RCC roof slab to required slopes with CM (1:3) prop. 20mm thick (average) mixed with water proofing compound at 1Kg/bag of cement, laid over roof slab when it is green, finished smooth with a floating coat of neat cement and thread lining at regular intervals of 45cmx45cm including Cost and Conveyance of all materials complete for finished item of work (APSS No. 901 & 903).(CSSR)

Brick Masonry in CM (1:8) with Non-modular traditional bricks of size 23 x 11 x 7 cm for Superstructure including cost and conveyance of all materials, all labour charges, curing charges and scaffolding charges etc complete for finished item of work for Super structire

Reinforcement birck masonary walls of 11.5cm in CM (1:6) using 2nd bricks having a crushing strength of not less than 35.00Kg/cm2 and using two mild steel bargs of 6m dia in every third layer of brick masory, with free joints of the main block work including cost and conveyance of all materials and water from approved sources to work site and all operationsl, incidental labour charges such as scaffolding mixing mortor constructing masonary lift charges, curing including Overheads & Cotractors Profit . complete but execluding the cost of steel and its fabrication charges for finished item of work as per SS 509 for super structure

Supply and fixing of MediumTeak wood Door Double shutter fully pannlled door of size 1.20 x 2.10mt with frame made of well seasoned teak wood scantlings of size 100 x 75mm mm and shutter made of side rails 125mm X38, top rail 125mmX38mm, bottom rail 125mmX38mm and intermediate rails of 125 x 38 mm and panels - 8 no's are of 25mm thick as per approved design with fixtures of 6 nos of 9" ' z" holdfasts, 250 mm long MS power coated aldrop-1 no,250mm long brass latch,125mm long butt hinges 8No's, Door stoppers-2 no, MS Power coated 150 mm long Tower bolts - 2no's Poer coated, MS power coated fancy handles 150mm long 2no's, with necessary screws complete including cost and conveyance of all materials and labour charges etc. complete as per specifications (APSS NO.1001 & 1002 (CSSR)

Supply and fixing of MediumTeak wood Door Double shutter fully pannlled door of size 1.00 x 2.10mt with frame made of well seasoned teak wood scantlings of size 100 x 75mm mm and shutter made of side rails 125mm X38, top rail 125mmX38mm, bottom rail 125mmX38mm and intermediate rails of 125 x 38 mm and panels - 8 no's are of 25mm thick as per approved design with fixtures of 6 nos of 9" ' z" holdfasts, 250 mm long MS power coated aldrop-1 no,250mm long brass latch,125mm long butt hinges 8No's, Door stoppers-2 no, MS Power coated 150 mm long Tower bolts - 2no's Poer coated, MS power coated fancy handles 150mm long 2no's, with necessary screws complete including cost and conveyance of all materials and labour charges etc. complete as per specifications (APSS NO.1001 & 1002 (CSSR)

Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of size with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebat of 32MM. Door Frame section of 63.5x100 MM .The two Vertical members are to be joined together with the horizontal member using 8x75 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member.

Providing and fixing 28 -30 MM thick solid Wood Polymer Composite(WPC) single extruded Door Shutter with 3MM top and bottom rigid layer with an overall density of 750kg/Cum. It will be fixed to the frame using 3 inch /4 inch hinges. A minimum of 4 hinges will be required for fixing the door with the frame

Supplying and fixing of MS Iron Window grills using MS angles of 25 x 25 x 5 mm size for outer frame, including cost and conveyance of all materials ,fabrication charges and all other labour charges etc., complete.

Supplying and fixing of Stainless steel hand railing as per approved drawing with top rail of 64mm dia (outer) 2mm thick pipe, vertical balusters of 50mm dia 2mm thick at 600mm c/c spacing (7 Nos)and 3 nos 25mm dia (outer) 1.6mm thick stainless steel pipes below top rail with equal spacings and 50mm wide 8mm thick SS plate for fixing vertical balusters at 600mm centre with 100x100mm stainless steel base plate to be fixed to the steps with Anchor fasteners. The rate should include providing and using bonding agent, drilling of 25mm holes of fixing railing , polishing of all nos of railing thouroughly and also including cost and conveyance of all materials, electrodes, welding charges, cost of all consumables, labour charges such as for fabrication of SS pipes, buffing, polishing etc., complete for finished item of work.

Providing and fixing factory-made uPVC any colour sliding glazed window upto 1.50 m in height dimensioncomprising of uPVC multi- chamberedframe with in-built roller trackand sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from rollforming process of required length (shape & size according to uPVCprofile), appropriate dimension of uPVC extruded glazing beads anduPVC extruded interlocks, EPDM gasket/TPV, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylonrollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mmsize for fixing frame to finished wall and necessary stainless steel screwsetc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage ofwater etc. After fixing frame the gap between frame and adjacent finishedwall shall be filled with weather proof silicon sealent over backer rod ofrequired size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge inclusive of cost of Single / double glass panes, wire mesh and silicon sealent . Note: For uPVC frame and sash extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be acceptedbut no extra payment on this account shall be made.

Ornamental Plastering with CM (1:3), 12 mm thick for exposed surfaces of R.C.C. works including cost and conveyance of all materials, all labour charges, curing charges and scaffolding charges etc complete for finished item of work for Ground Floor:

Plastering with CM 2 coats, 12 mm thick, base coat in CM (1:6), 8 mm thick and top coat in CM (1:4), 4mm thick with Dubara sponze finishing.Internal walls for Ground Floor

Plastering with CM 2 coats, 20mm thick, base coat in CM (1:6), 16mm thick and top coat in CM (1:4), 4mm thick with sponze finishing including cost and conveyance of all materials and all labour charges etc., complete for walls for Ground Floor:

Painting to New Wood work with two coats of ready mixed synthetic enamel paint first quality all shades over a base coat of wood primer making three coats in all to give an even shade after thouroughly brushing the surface to remove all remains of loose powderedd materials, including c/c of all materials, site and other taxes, all operational, incidental and labour charges etc., complete for finished item of work in all flooring for external walls. (APSS No.1201, 1207 & 1212)(CSSR) for 1 sqm

Providing and applying synthetic plaster putty or plaster of paris putty or lime punning of average 1 to 2 mm thickness over plastered surface to prepare the surface even and smooth after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, Sand the surface, clean & wipe off loose dust, applying knife paste filler by putty knife/ muslin pad, air dry for 2 - 3 hrs, sand with 180 and 320 No. emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work for internal walls.

Painting to new walls and ceiling in two coats with Plastic Emulsion Paints Asian/ Berger/ Nerolac or equivelent and shaded over Priming Coat with Cement Primer water base interior Gr -1 or equavalent quality to give an even shade after thoroughly brushing the surface to remove all loose powdered materials including cost and conveyance of all materials and water to site, sales & other taxes, all operational, incidental and labour charges such as cleaning the surface, painting, curing etc., complete for finished item of work for internal walls. (APSS No.901 & 908)

Painting to New walls with two coats of plastic Emulsion Paints Asian / berger/ Nerolac or equavalent quality of approved shade over base coat of cement primer grade 2 making three coats in all to give an even shade after thoroughly brushing the surface to remove all loose powdered materials, including cost and conveyance of all materials, including cost and conveyance of all materials, cost of brushes, water to site, etc., sales & other taxes, all operational, incidental and labour charges such as scaffolding charges, lift charges, curing etc., complete for finished item of work in all floors for External Walls.(APSS No. 912)

Flooring with non-skid Double charged / multi charged stain free full body porcelain vitrified tiles with double layer pigment of size 600 x 600 mm and thickness between 8-10 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs with borders and design as per the approved flooring pattern as directed by the Engineer-In -Charge, laying tiles using spacers of 2mm thick, set over a base coat of CM (1:8) prop. 12mm thick using screened sand over CC bed already laid or RCC roof slab , including neat cement slurry of honey like consistancy spread @ 3.3 kgs per sqm. and jointed neately with white cement paste to full depth mixed with pigment of matching shade including cost and conveyance of all materials like cement, sand, water, tiles, white cement etc., to site (excluding cost of C.C. bed) including cost of base coat and all labour charges for mixing of cement mortar, laying tiles to required slope as directed by the Engineer- in-charge etc.,and overheads & contractors profit complete for finished item of work. (APSS No.701 & 707.

Providing skirting 10 cm height with Double charged / multi charged stain free full body porcelain vitrified tiles with double layer pigment of Size 600 x 600 mm and thickness between 8-10 mm of any colour and finish in all shades and designs, length equal to flooring tiles, flushed to wall surface to set over base coat of CM(1:5) 12 mm thick using screened sand with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointing with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc.,and overheads & contractors profit complete for finished item of work.(APSS No.701 &707)

Flooring with non-skid red or white full body Ceramic floor tiles of size 300 mm x 300 mm and thickness between 7-8 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs as approved by Engineer-in-charge, set over base coat of cement mortar (1:8), 12mm thick using screened sand over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 Kgs per sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, screened sand , water and tiles etc., and overheads & contractors profit complete for finished item of work. (APSS No.701 & 707)

Dadooing to walls with glazed red or white full body ceramic wall tiles of size 200 x 300 mm and thickness between 6-8 mm 1st quality, set over base coat of CM (1:3) 12 mm thick with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointed with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc., complete for finished item of work.

Supplying, fitting and placing HYSD bar reinforcement (Fe 500 / Fe 500 D grade as per IS 1786-1979) of different diameters for RCC works including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying etc., and overheads & contractors profit complete for finished item of work.( APSS No.126) for Ground Floor:

Supply and installation of Double grooved and precoated extruded mineral (cement) roof tiles of size 420 mmx330 mm of corrugated profile tiles with variable overlapping for coverage of 1-1.2 per tile with European standards BEEN 490:2004

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per Technical Specification 305 MORD / 304 MORTH

Plain Cement Concrete corresponding to M7.5 grade as per IS 456 equivalent to (1:4:8) proportion nominal mix (cement: fine aggregate: Coarse aggregate) using 40mm size Hard Blasted Granite (IS383, 1970) metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, including seigniorage charges, sales & other taxes on all materials, all operational, incidental, and labour charges such as mixing, laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete for finished item of work for Foundations (APSS No. 402)

Design Mix Concrete M30 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for Raft

Brick masonry in CM (1:6) with bricks of traditional size 23 x 11 x 7 cm 2nd class including cost and conveyance of all materials and all labour charges etc., complete for finished item of work for below Basement

Providing Impervious coat to exposed RCC roof slab surface with CM(1:3), 20mm thick with 1kg of water proof compound per bag of cement laid over roof when it is green including cost and conveyance of all materials all operational, incidental and labour charges for mixing mortar, laying, rendering smooth and thread lining, curing, rounding off junctions of wall and slab etc., complete for finished item of work.

Reinforced Cement Concrete M-30 Design mix (Cement: Fine aggregates: Coarse aggregates) corresponding Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like Cement, fine aggregate( Sand), coarse aggregate, water etc to site and including sales and other taxes on all materials including all operational, incidental and labour charges such as machine mixing, laying concrete, curing etc complete but excluding cost of steel and its fabrication charges for finished item of work, but including centering, shuttering for finished item of work Slab of 100mm thick

Supplying and fixing of 110mm dia SWR/ PVC pipes (as per ISI standards) 4 Kg/Sq.cm. Prince/sudhakar or any ISI brand and fixing all special such as plain bends, off sets, door bends, single junctions, double junctions as per site requirement, fixing with PVC clamps if necessary with required number of Bombay nails including cost and conveyance of all materials to site, labour charges etc.complete for finished item of work at all floor levels. (APSS No. 1302 1319 & 1326)

Providing high yield strength deformed (HYSD) steel bars (Fe 500 grade as per IS 1786-1985) of 8mm to 40mm diameters, cutting, bending, to required sizes and shapes placing in position with cover blocks of approved size and binding wire of 20SWG, forming grills for reinforcement work as per approved designs and drawings including cost and conveyance of bars from approved sources to site of work, including cost and conveyance of binding wire, cover blocks and all operational, incidental, and labour charges such as cutting, bending, placing in position, tying etc., and sales & other taxes,on cost of all materials complete for finished item of work

Supply and fixing of 25mm dia 1.8mm thick P.V.C. pipe (ISI Mark) concealed in wall with all required accessories including masonary work and labour charges etc., complete.

Supply and fixing of 25mm dia 2.2mm thick P.V.C. pipe (ISI Mark) concealed in Roof Slabs with all required accessories including masonary work and labour charges etc., complete..

Wiring with 2 runs of 14/0.3mm (1.0 Sq.mm) Fire Retardant (FR) P.V.C. insulated flexible copper cable (ISI MARK) in existing pipe with 6A switch, Ceiling rose and 3mm tick hylam sheet covering to switch control box including all labour charges etc., complete for light, bell, fan and exhaust fan points in Non-Residential buildings. .

Supply and fixing of 6A 3 pin wall plug socket with a 6A switch control on a common switch board with earth continuity including wire leads, earth connections along with all labour charges etc., complete..

Supply and fixing of 16A 3pin flush type switch socket combined (2 in 1) duly recessed in wall with wooden deep box of 6"x8"x21/2" size covered with hylam sheet including earth connections and all labour charges etc., complete.

Supply and fixing SPN Distribution board with IP-20 protection suitable for single phase Earth Leakage Circute Braker (ELCB) / Residual Current Circute Braker (RCCB) / Double Pole (DP) Isolator as incomer and 10kA SP MCBs as out going including internal connections and labour charges for surface / flush mounting etc., complete.

Supply and run of 1 of 14 /0.3mm (1.0 Sq.mm) FR P.V.C. insulated flexible copper cable in existing pipe for earth continuity including all labour charges etc., complete.

Supply and run of 2 of 36/0.3mm (2.5 Sq.mm) F.R. P.V.C. insulated flexible copper cable in existing pipe for mains including all labour charges etc., complete.

Supply and run of 2 of 56/0.3mm (4 Sq.mm) F.R. P.V.C. insulated flexible copper cable in existing pipe for mains including all labour charges etc., complete.

Providing independent earthing by excavating a trench to a depth of 2.1M in all soils, as per size specified in the Data, using 40mm dia. 'B' class GI pipe of 2.5 Mtrs Length with necessary accessories with hume pipe ring duly providing staggered holes including filling with equal proportion of Salt and Charcoal in layers and all labour charges etc., complete for small quarters.

Supply and fixing of batten holder / slanting holder in lieu of ceiling rose of light point complete with all connections and all labour charges with 40W bulb (for new installation).

Supply and fixing of 20-24W, not less than 1100mm length LED batten light with extruded aluminum housing and polycarbonate cover, input voltage AC 220 - 260 Volts, with high power LEDs, having System Efficacy of >=90 lumens/watt , PF>0.9, Surge protection: 2KV, THD<15%, with inbuilt driver and frosted cover CCT: 3000K - 5700K, minimum CRI>70, etc., complete with earth connection and not less than two years warranty. Makes: Surya /C&S/ Fortune Arrt / Syska / Enrich / Stanjo / Polycab/ Ib LED/ Opple/ Luker/ Orbit/ Trinic/Lumens/ GLO LED / Vimal /Benlo /Goldwyn /Sturlite /AJUSS/Orient b) LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG / EVERLIGHT.

Supply and fixing of 48" (1200mm) Sweep 5 Star rated Ceiling Fan without Regulator with all standard accessories of makes Makes : Crompton HS Decora / Bajaj Regalstar / Havells Fusion 50 / Orient Summer Crown / Usha technix decorative including transportation and giving connections with twin core wire etc., complete.

Supply and errecting stepped type regulator for ceiling fans 900/1200/1400 sweep complete errected on existing board

Providing & Placing on Terrace (at all floor levels) polyethylene water storage tank with Double layer approved brand & manufacture with cover and suitable locking arrangement & making necessary holes for inlet & outlets and over flow pipes but without fittings & base support for tanks including cost of conveyance of all materials and labor charges, complete for finished item of work. -

Providing 110 mm Dia ISI marked PVC down water take pipes with socket, 2.5mm thick 4.0 kg/sq.cm pressure of ISI marked including cost of necessary PVC Bends, shoes, iron/ PVC clamps and all other accessories and fixing in position including cost and conveyance of all materials, operational & incidental charges including all labour charges for fixing at site etc., for finished item of work.

Providing 75 mm Dia ISI marked PVC down water take pipes with socket, 2.5mm thick 4.0 kg/sq.cm pressure of ISI marked including cost of necessary PVC Bends, shoes, iron/ PVC clamps and all other accessories and fixing in position including cost and conveyance of all materials, operational & incidental charges including all labour charges for fixing at site etc., for finished item of work.

Supply & fixing of tested NP bib taps at all levels of 12.70mm dia of Indian make first quality ( N.P bib tap indian make 400 g ) Long body including cost & conveyance of all materials, labour charges for finished item of work complete for all floors

Supply & fixing white glazed European water closet with variety as approved by Engineer-in-charge ,P" orS" trap with 4" CI outlet pipe of approved make,plastic seat and lid for EWC and rubber buffers as per ISI 2548 1963 with and 10 lits capacity PVC slimline low level flush tank of approved make with internal components and fixed with wooden gutties with required size nails,32mm dia short CP bend,12mm PVC Connections with brass union nuts and 12.70 mm (1/2") NP stop cock heavy duty (300 grams) complete including cost and conveyance of all materials to site,for finished item of work for all floors.

Supplying & Fixing Indian make Flat Back Wash Hand Basin 1st quality conforming to IS:2556-Part-4:1972 with waste fittings like rubber plug, chain,32 mm nominal size C.P. Fitting with parallel pipe thread conforming to IS:2963-1979 and fitted with 15 mm nominal bore Chromium Plated Pillar including wooden block: 550 x 400 mm - Single C.P. Pillar cock.

Supply & fixing bib cock cum health faucet with 1 m long flexible tube and wall hook of Jaquar make queen series with 7 years warranty Chrome plated

Providing & fixing GM gate / ball valve of 32 mm dia as per IS -778 Class - I, Indian make heavy type, including cost & conveyance of all material to work spot and all labour charges including fixing in position for finished item of work and all taxes.

4" (101.6 mm ) multi floor trap with Jali- UPVC/SWR Pipe fittings

4" (101.6 mm ) Nahany Trap ( Without Jali with inlet)UPVC/SWR Pipe fittings Each

Supply & fixing of 110 mm dia - Vent Cowl - UPVC/SWR Pipe fittings (Prince/ Sudhakar/ Kisan/Supreme or any ISI Brand) including cost and conveyance of all materials to site, all labour charges complete for finished item of work

Supplying & fixing stainless steel sink size 20" x18" x 8 "(508x457.2x203.2mm) 1 mm thick with accessories

Supply and Fixing of Premium make CPVC Pipes and Fittings to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper Tube Sizes 1/2" ton 2" SDR 11 and SDR 13.5 pipes are made from idential CPVC compounds having the same physicalProperties for Hot and Cold Water (IS 15778:2007) 15.90mm dia OD Pipe

Supply and Fixing of Premium make CPVC Pipes and Fittings to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper Tube Sizes 1/2" ton 2" SDR 11 and SDR 13.5 pipes are made from idential CPVC compounds having the same physicalProperties for Hot and Cold Water (IS 15778:2007) 22.2mm dia OD Pipe

Supply and Fixing of Premium make CPVC Pipes and Fittings to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper Tube Sizes 1/2" ton 2" SDR 11 and SDR 13.5 pipes are made from idential CPVC compounds having the same physicalProperties for Hot and Cold Water (IS 15778:2007) 28.60mm dia ODpipe

Drilling of Bore well by down the hole hammer drilling to a finished dia of 112/165 mm dia in all formations suitable for down the hole hammer drilling such as medium hard rock formation to hard rock formation, all consolidated formation etc. and drilling in over burden to dia not less than 200 mm etc and reaming the bore well to suit insertion of suitable casing pipe etc., including insertion of casing pipe with couplings, caps any other relevant materials upto required depth as directed by the department including transportation of drilling rigs and supporting vehicle and including bore development (Flushing of Bore Well at an average pressure of 150 PSI) conducting yield test, consumables charges, Crew charges required in fixation of pipe assembly completely done to the satisfaction of the department and including all labour charges but excluding all taxes, the cost of casing pipe, couplings, cap etc., The entire work should be carried out as per IS -2800 Part I & II 1979 and amended from time to time.

Cost and supply of 140mm dia UPVC calss-III pipe including all charges.

Cost and supply of 180mm dia UPVC calss-III pipe including all charges.

Sloting charges for 140mm dia UPVC calss-III pipe including all charges.

Geological survey for selection of site for hand pump by the Geologist

Supply and Transportation of 1.Hp, 5star rated submersible motor pumpset, confirming to IS 8034 and motor confirming to IS 9283 with waterproof winding, pump shall be suitable for various delivery head and discharge with stainless steel shaft motor suitable for working on 240V ± 10%, single phase 50 Hz AC supply, etc complete for 4" Bore well. Makes: As per list of recommended brands as category I. Makes: Kirloskar / Crompton / CRI / KSB / Texmo ELEC-5.4.2

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per Technical Specification 305 MORD / 304 MORTH

Sand filling in foundation / basement from approved Quarry / available sources including all operational, incidenal, labour charges, Hire Charges of T&P etc., complete (excluding rock) in trenches, sides of foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and cost and conveyance of water to site and all operational, incidental, labour charges, , sales and other taxes etc, hire charges of T & P etc., complete for finished item of work. (APSS NO. 309 & 310) for finished item of work

Plain Cement Concrete corresponding to M7.5 grade as per IS 456 equivalent to (1:4:8) proportion nominal mix (cement: fine aggregate: Coarse aggregate) using 40mm size Hard Blasted Granite (IS383, 1970) metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, including seigniorage charges, sales & other taxes on all materials, all operational, incidental, and labour charges such as mixing, laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete for finished item of work for Foundations (APSS No. 402)

Masonry work in CM (1:6) proportion (Cement : Screened sand) in superstructure with fly ash cement / lime solid blocks of size 290 mm x 225 mm x 140 mm from approved source having minimum crushing strength of 50 Kg/Sqcm. including cost and conveyance of all materials like cement, sand, bricks, water etc., to site, including sales & other taxes on all materials and such as labour charges, like mixing cement mortar, scaffolding charges, constructing masonry, lift charges, curing, overheads and contrctor profit etc., complete for finished item of work. (APSS No. 501 & 504) for For basement

Design Mix Concrete M20 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for FOOTINGS

Design Mix Concrete M20 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for PEDASTALS

Design Mix Concrete M20 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for COLUMNS

Design Mix Concrete M20 Design mix corresponding to IS 456 using with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. for Plinth Beam

Brick Masonry in CM (1:8) with Non-modular traditional bricks of size 23 x 11 x 7 cm for Superstructure including cost and conveyance of all materials, all labour charges, curing charges and scaffolding charges etc complete for finished item of work

Supplying and fixing of MS Iron Window grills using MS angles of 25 x 25 x 5 mm size for outer frame, including cost and conveyance of all materials ,fabrication charges and all other labour charges etc., complete.

Plastering with CM 2 coats, 12 mm thick, base coat in CM (1:6), 8 mm thick and top coat in CM (1:4), 4mm thick with Dubara sponze finishing.Internal walls

Painting to New walls with two coats of plastic Emulsion Paints Asian / berger/ Nerolac or equavalent quality of approved shade over base coat of cement primer grade 2 making three coats in all to give an even shade after thoroughly brushing the surface to remove all loose powdered materials, including cost and conveyance of all materials, including cost and conveyance of all materials, cost of brushes, water to site, etc., sales & other taxes, all operational, incidental and labour charges such as scaffolding charges, lift charges, curing etc., complete for finished item of work in all floors for External Walls.(APSS No. 912)

Supplying, fitting and placing HYSD bar reinforcement (Fe 500 / Fe 500 D grade as per IS 1786-1979) of different diameters for RCC works including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying etc., and overheads & contractors profit complete for finished item of work.( APSS No.126) for Ground Floor: