Annual Repair of Civil Hospital Building at Ambala Cantt in Ambala District

Amount

I) Civil Works Cement concrete 1:2:4 with stone aggregate 20 mm nominal size in pavements, roads, taxi-tracks and runways, laid to required slope and camber, including consolidation, finishing and tamping complete. (HSR 10.132)

Providing and laying 80mm thick interlocking paver blocks ISI marked (IS code: 15658:2006) of all shapes and colours in design mix cement M-40 as per IRC:SP:63-2004, over a bed of 30 mm thick fine sand complete in all respects. [HSR 10.159]

Tile terracing with one layer of tiles, 22.86 cm X 11.43 cm X 3.81 cm laid dry over a layer of mud mortar including grouting with cement sand mortar 1:3 and top surface to be left clean. (HSR 13.14)

Conglomerate floor 40 mm thick Cement Concrete topping 1:2:4. (HSR 14.9)

Precast chequered tiles of 20 mm thickness In ordinary grey cement without chips laid on 20 mm thick bed of cement coarse sand mortar 1:3 with neat cement slurry between joints and over the base in floors, treads of steps and landings. (Note:- Reputed make Tile Only ISI marked will be used as approved by Engineer-in-charge). (HSR 14.45). Note:- The Agency to whom the work is allotted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Kotah stone flooring minimum 25 mm thick in any pattern as specified over 12 mm thick base of cement coarse sand mortar 1:3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing. (HSR 14.62). Note:- The Agency to whom the work is allotted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. First Storey

White glazed tils 10 cm X 10 cm, 5 mm thick in skirting and dado on 12 mm thick cement coarse sand plaster 1:3 in base and jointed with white cement slurry in joints, including bevelled corners. (HSR 14.48) (a) (ii)

12mm thick cement plaster on walls (1:6). (HSR 15.7).

Cement pointing 1:2 deep variety on brick and Tile work (HSR 15.60)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (HSR 16.3)

Painting two coats excluding priming coat with ready-mixed paint for metallic surfaces in all shades on new steel or iron work. (HSR 16.17)

Painting two coats with ready-mixed exterior paint in all shades on newly plastered or concrete surface of walls. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.26).

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge).. (HSR 16.60)

Providing two coat of exterior acrylic emulsion paint. (Note:- second quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.79 (a)).

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- reputed make Putty such as J.K./ Birla shall be used as approved by Engineer-in-charge). (HSR 16.81).

Supplying and fixing glass panes with moulding of commercial hard wood such as hollock, champ, chikrassy and chaplash etc. (Non coniferous timber other than teak, conforming to I.S. specification No. 1003, kiln seasoned)- (HSR 17.36) (c) 4mm thick (glazing area above 55 sq. dm, but upto 84 sq. dm of each pane) (HSR 17.36 (c)).

Providing and Fixing of Granite stone complete in all respect.

II) Public Health Works Providing and fixing in position best Indian make (to the approval of the engineer-in-charge). Indian type Orissa or Orya water closet suite for sinking into floor, with raised foot treads complete with 100 mm H.C.I, ‘p’ trap with or without vent as required and all other necessary fittings as fully described in item no.30.1 above (HSR 30.2 (a) (i) (a) Size 580 mm (i) White (Hindware, pareware or equivalent make)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (as approved by the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUITE, SYPHONIC TYPE, Consisting of- (HSR 30.5) (a) Single trap symphonic W.C. Suite (HSR 30.5 (a) (i) White ((HSR 30.5 (a) (i)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE LAVATORY SUITES (ANGLE BACK) IN VITREOUS CHINAWARE and all Others necessary fittings as fully described in Item no. 30.41 above. White Size 530 mm x 430 mm with one no. tap. (HSR 30.43)

PROVIDING AND FIXING IN POSITON BEST INDIAN MAKE CHROMIUM PLATED BRASS 2ND TRAP FOR LAVATORY SUITE. (HSR 30.45)

Providing and fixing in position best quality Stainless Steel Sinks with Complete fittings as fully described in item No. 30.51. (a) 600 mm x 450 mm x 200 mm. (HSR 30.53 (a)).

Providing and laying of G.I. pipe 1/2" dia. (NS)

Providing and laying of G.I. pipe 3/4" dia. (NS)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE SHOWER WITH 15 OR 20 I/D IN-LET. (HSR 30.66) C) C.P. brass with revolving joint (HSR 30.66 (C))

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRRON Mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHORMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall or chromium plated brass clamps with C.P brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (HSR 30.71) (a) INDIAN MAKE (ii) 550 mm x 400 mm

Providing & fixing in position 15mm i/d CP Brass Bib Cocks of best quality (as required by the Engineer – in – Charge) (HSR 30.75) a) Bib cock Long Body (HSR 30.75 a)

b) Bib cock (HSR 30.75 (c))

Providing & fixing in position CP Brass stop cocks (as approved by the Engineer – in – Charge) (HSR 30.76) (a) 15mm STOP COCK (i) Stop cock male and female end (HSR 30.76 (a) (i)

Providing & fixing in position CP Brass stop cocks (as approved by the Engineer – in – Charge) (HSR 30.76) (a) 15mm STOP COCK (ii) Concealed stop cock with flange (HSR 30.76 (a) (ii)

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P brass screws and complete in all respects including cutting and making good the wells etc. (HSR 30.70) a) C.P BRASS (HSR 30.70 (a) (i) Soap dish 160 mm (HSR 30.70 (a) (i)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE TOWEL RAILS FIXED in with rawlslugs embedded in walls with C.P brass screws. Complete in all respect INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (HSR 30.68) a) 25 MM DIA C.P BRASS ADJUSTABLE i) 750 mm long

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE TOWEL RAILS FIXED in with rawlslugs embedded in walls with C.P brass screws. Complete in all respect INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (HSR 30.68) e) C.P brass towel ring.

CONSTRUCTING BRICK MASONRY INSPECTION CHAMBER SIZES AS GIVEN BELOW UPTO 0.60 METRE AVERAGE DEPTH in cement Mortar 1:5 LIME CONCRETE with 40 percent lime mortar 2:3 in foundation Cement mortar 1:2:4 BENCHING 12 mm THICK CEMENT PLASTER 1:2 with a floating coat of 1 mm thick of neat cement R.C.C 1:2:4 SLAB 100 mm THICK/CC/ TOPPING 50 mm THICK WITH 455 MM x 455 MM X 610MM INSIDE LIGHT DUTY C.I. INSPECTION CHAMBER COVER AND FRAME Weight as per I.SI. specification painted WITH 3 COATS OF black bitumastic superior paint complete as per standard design. (HSR 29.84) (b) Size 450 mm x 600 mm inside (with 455 mm x 610 mm cover and frame light duty single seal pattern I weighing 38 kg with C.C.topping )

Providing & fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers / lids marked with IS :12701 on roof top of buildings including coat of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer – in – Charge. (Except civil work) (HSR 30.119) C) 500 ltr. capacity

Providing & Fixing PVC Rainwater Pipe 6 kg. pressure of ISI mark in cement mortar during masonry work. (Note:- Reputed make PVC Pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. (HSR 13.89). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. (a) 100 MM dia PVC pipe 6 Kg. Pressure.

(b) 150 MM dia PVC pipe 6 Kg. Pressure.

Providing and fixing PVC Bend ISI Mark. (Note:- Reputed make PVC Bend such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. (HSR 13.90). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. (a) 100 mm dia PVC Bend

(b) 150 mm dia PVC Bend

JAGDEEP SINGH

Vikas Sharma

M S Raj Associates