Setting up of Monsoon research laboratory at EESSC first floor in IISER campus, Vithura

Amount

Dismantling tile work in flooring/ dado laid in cement mortar including removal of back mortar, screed concrete etc. stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Cement Plaster (IN FINE SAND) 1:6 (1 cement: 6 fine sand)

LVT flooring Supply and laying of LVT flooring 5 mm thickness with 0.50 wear layer (luxury vinyl flooring of approved design and pattern, as per the architect's approval and instruction). Type of flooring: Vinyl synthetic floor covering, heterogeneous with EPT Sheild (Anti Bacterial and anti fungal), SGBP Certified. Overall thickness:- EN ISO 24346: 5.0 mm. Thickness of the wear layer: ISO 24340: 0.50-0.55 mm. Abrasion group: EN 660-2, Class T. Binder content wear layer: EN ISO 10582 typer I (HPD certified). Level of use: EN ISO 10874 class 23/33/42. Dimensional stability: ISO 23999<0.10% and cooling after exposure to heat <1.0 mm. Safety criteria: Fire resistance EN 13501-I Bfl-s1 (Class A), Slip resistance: EN 13893 (DS), DIN 51130-R 10 light fastness: ISO 105-B02>6 performance impact sound reduction: EN ISO 10140-3 (9 dB), resistance to chemicals: ISO 26987 (no damage) Warm water: under floor heating suitable max. 27 °C static load limit: ASTM F970 <0.005 in @ 250 psi min Formaldehyde Group: EN 717-1 (Ei0 VOC emissions: IAC Gold Certified very low Volatile Organic Compounds (VOC) of approved quality complete as per the suggestions from the architect/engineer in charge. Approved make: Merino, Shaw Flooring, COREtec.

ROLLER BLINDS Supply and installation of moisture-resistant roller blinds (including the pelmets) of approved shade of weight 330 g/sq. m. ±5%; 100 % Blackout Polyester material should be used, Extrication Formaldehyde amount less than 30 ppm. Fabrics type should be Blackout make of 100% Polyster with Blackout Rate 100%, fabric thickness 0.45 mm (± 0.05), light fastness 4 Grade, excellent hanging propeties, very high tearing strength, with Acryilc coating resistant to cracking and fraying, conditionally cleanable with damp cloth. Approved shade of roller blinds should be decided as per the design confirmed by the consultant/customer and engineer-in-charge. Approved brands: Vista, NI, MAC, HunterDouglas.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board,two coats of putty,approved emulsion paint etc all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour

Two coats or more coats

Linear Shaped workstation 19mm thick BWR Plywood with 1mm thick laminate pressed on one side and 0.8 mm thick laminate pressed on non visible sides. If visible sides should press both sides 1mm laminate. Back Board and Drawer Bottom on 8mm thick plywood with 0.8mm thick off white colour cold pressed on both sides 75mm thick Partition system with heavy duty levellers 1200mm High and 1200mm L both sides to be PLPB 9mm board/White board/pinnable board/ fabric board as appropiately directed by the client and Side partition with 8mm thick frosted glass on partition clamp or Lacquered as per the Architect specification.Overall dimension 1200mm L x 600mm D x 750mm H(module size may change as per the site condition,top area will taken for measurement purpose)

Under Cabinet Pedestals Overall dimension 400mm L x 450mm D x 650mm H 16mm thick Plywood with 1mm thick laminate pressed on one side and 0.8 mm thick laminate pressed on non visible sides. Back Board and Drawer Bottom on 8mm thick plywood with 0.8mm thick off white colour cold pressed on both sides Multi Drawer Locking system Good Quality Sliders Handles / Locks Wheels if necessary

Table Folding Shelf with Bracket of 20 " to hold 600mm x 600mm 18mm thick Table Top(BWR Plywood) rate inclusive offixing charges ,all as per the direction of EIC