PROVISION OF DOUBLE NETTING FOR BIRD PROOFING AND ADDITION OF SITTING ROOM IN PARKING AREA HARDSTANDING FOR HARPOON AND SPECIAL REPAIR OF SQUASH COURT WOODEN FLOORING AT ICGAE PORBANDAR UNDER GE (I) CG PORBANDAR

Amount

Schedule 'A' B/R

Material & Labour for bird hazardous nylon wire net of 1.5mm dia and avg aperture of net approx. 50mm including cotton rope of dia 10mm, U bolt clamp of size 30mm, round ring of dia 30mm, D shackle of 50mm and including all arrangement for fixing the net, complete all as specified and directed by Engineer-in-Charge. Note: Overlap of net shall be measured separate.

Supply and fixing stainless steel rope of dia 6mm for fixing of nylon wire netting including necessary arrangement etc., complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work as gates, including pintle hinges, stops, hand-made sliding bolts, etc. conforming to Fe.290.Gde-E-165, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc. 5cm but not exc. 10cm long Dia meter of Shank 5 to 10mm, complete all as specified and directed by Engineer-in-Charge.

Excavation over area not exceeding 1.50 Metre deep and getting out in hard/dense soil, complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm as in Hard/Dense rock, complete all as specified and directed by Engineer-in-Charge.

Removing excavated soil exceeding 500 Metre and not exceeding 1.50 Km depositing where directed at a level not exceeding 1.5 Metre above the starting point, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation and mass concrete, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 75mm thick Plain Cement concrete type D-2, 1:4:8 (using 40mm graded aggregate) as in sub base of floors, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for PCC (1:2:4) type B-1 using 20mm graded aggregate as in floor of average 25mm thick including preparation of existing surface, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for moorum/red bajri filling in floors or pavings, laid in layers not exceeding 15cm thick, spread, levelled and rammed including watering, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Porbandar stone masonry, well bonded, bedded and solidly hearted built in Cement Mortar 1:6, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for rendering 15mm thick on fair face of brick work or concrete surfaces in Cement Mortar 1:4 finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 15mm thick rendering in Cement Mortar 1:6 to brick/concrete wall surfaces trowelled to even & smooth w/o using extra cement, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for preparation of new plastered surfaces of wall and applying two coats of 100 % Premium acrylic emulsion paint having VOC less than 50 gm/ltrs and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm all as per the manufacturer’s instructions, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for preparing surfaces plastered or un-plastered new surface of walls applying two coats of oil bound distemper over a coat of primer over layer of smooth Putty finish two coats as per manufacture instruction with smooth roller finish, complete all as specified and directed by Engineer-in-Charge. Note:- after painting, cleaning of all floors, glass & furniture by own arrangement.

Material & Labour for Vitrified ceramic tiles (dark shade) 10mm thick (square /rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.0 sqm in vertical surfaces etc., set and jointed in neat cement slurry and pointed in white or coloured cement to the match, including 15mm thick screed bed in cement mortar 1:6 over, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for glazed coloured ceramic tiles in vertical surfaces 250x250x7mm / 450x 350x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match over screed bed or bedding layer 10mm thick 1:4 and pointed in white or coloured cement to match, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 12mm thick Gypsum Board seamless Ceiling as in curved, sunken or raised surface of any design as approved and finishing the surface fair by filling the joint with POP and including GI frame work for curved, sunken or raised for any design as approved as in ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleats and steel expansion fasteners with and including ceiling section (not exc 1.20 m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.50mm fixed to the intermediate channel at 457mm centre to centre fixed with hanger of GI channel outgoing channel used as above upto 1200mm length in roof slabs by means cleats, complete all as specified and directed by Engineer-in-Charge. Note: Flat area will be measured.

Material & Labour for 12mm thick Gypsum Board seamless Ceiling as in flat surface, finishing the surface fair by filling the joint with POP and including GI frame work as flat surface approved as in ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900 mm centre to centre with GI cleats and steel expansion fasteners with and including ceiling section (not exc. 1.20 m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.50mm fixed to the intermediate channel at 457mm centre to centre fixed with hanger of GI channel outgoing channel used as above upto 1200mm length in roof slabs by means cleats, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 12mm thick toughness glass as in partition with patch fittings with cover plate of SS-304 Grade, necessary accessories etc. including cutting holes in any size in floor and wall, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 12mm thick toughness glass as in door with patch fittings with cover plate of SS-304 Grade, door closer fixed in floor necessary accessories etc. including cutting holes in any size in floor and wall, complete all as specified and directed by Engineer-in-Charge.

Dismantling boarding, any description, fixed in any position with nails, complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings, including removing rubbish off the premises, complete all as specified and directed by Engineer-in-Charge.

Demolition of stone slabs and tiles of any description or thickness Laid bedded and pointed in any mortar in floors/skirting, aprons etc., complete all as specified and directed by Engineer-in-Charge.

Material & Labour for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over 20mm screed bed of cement mortar 1:4, complete all as specified and directed by Engineer-in-Charge.

Material & Labour 20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over 15mm rendering with cement mortar 1:4, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 150mm thick cement concrete flooring type C-2, 1:3:6 using 20mm graded stone aggregate finished even and fair to receive the screed bed without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for excavating in post holes in Hard dense soil (or similar holes) each not exc. 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed by Engineer-in-Charge.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for roof trusses Fe-410 W (Gde E-250) quality B (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed by Engineer-in-Charge.

Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 25mm thick cement concrete flooring type B-1, 1:2:4 using 20mm graded stone aggregate finished even and fair to receive the screed bed without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Dismantling timber scantlings 40 sqcm and over in section, un-framed work in any position, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Second class hard-wood in scantlings wrought and fixed, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Plain, galvanised, mild steel sheeting, 0.80mm thickness in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 and fixed, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for applying evenly two coats of bitumen blown any grade, applied hot to concrete surface at the rate of 1.50 kg per square metre per coat, complete all as specified and directed by Engineer-in-Charge.

Supply, installation and finishing Air-Cush mapple wooden sports flooring system with 20mm thick (50 to 100mm width) kiln seasoned imported Maple wood (sycamore) surface board, in random length in tongue and groove shape (The edges of the boards will have a finger lock groove and the bottom side with air pass groove) over and including under frame made of commercial quality Fir/Spruce/Pine wood runners of 90/70 mm x 45 mm treated with anti-termite solution and fixed on the bottom side with 18mm thick air-cushioning pads by nails through the two wings at 350 mm c/c. Finally the floor will be machine sanded in uniform level and finished with imported non-skid DIN certified Polyurethane lacquer polishing, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for cutting into old masonry work including making good in cement mortar of the same mix as for new walling, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for game line marking to the courts as per Sport Manual, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for preparation of old decorated surfaces of walls by scrapping old paint with steel wire brush, and applying two coats of epoxy paint including one coat of epoxy primer necessary, complete all as specified and directed by Engineer-in-Charge.

Excavating in trenches, not exceeding 1.5 Metre wide and not exceeding 1.5 Metre in depth; hard rock for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sqm on plan and not exceeding 1.5 Metre in depth and getting out, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for PCC 1:3:6 type C-2 using (40mm graded stone aggregate) as in foundation and mass concrete, complete all as specified and directed by Engineer-in-Charge.

Rolling and consolidating to required gradient & camber or formation surface using power roller (wt exc 8 tonne but nexc 12 tonne) surfaces in cutting, complete all as specified and directed by Engineer-in-Charge.

Material & Labour 150mm (spread thickness) in two layers (75mm Each layer) Soling (or sub base) with broken boulders or quarried stone, interstices filled, surface formed and roller and consolidated to required gradient and camber, complete all as specified and directed by Engineer-in-Charge.

Material and labour for laying and compacting 150 mm thick (Compacted thickness) Wet Mix Macadam (WMM) grading as per table 400-13 of MoRTH specifications for Road and Bridge works 2013 manufactured in WMM plant material comprising of clean, crushed, graded aggregate and granular material premixed with water to a dense mass, spreading, leveling, watering and rolling with vibratory roller of capacity 8 to 10 Ton weight and consolidating to required gradient and camber. Complete all as specified and directed by Engineer-in-Charge.

Material & Labour Polythene film, black, 50 micron with over lapping 200mm laid in floors, complete all as specified and directed by Engineer-in-Charge.

Supply only 10mm thick sand cushioning of Fine aggregate (sand) for concrete, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 100mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in sub base to floors, complete all as specified and directed by Engineer-in-Charge.

Material and labour for pavement quality concrete (PQC) of minimum 28 days field flexural strength of 45 Kg/Sqcm of 4.5 Mpa aggregate gradation as per Table 3 of IRC 15-2017, coarse aggregate of clean, hard strong, dense, non-porous and durable pieces of crushed stone or gravel fine aggregates of clean natural sand or crushed stone sand or combination of both using minimum 400KG/Cum of cement with non-circular, virgin synthetic fibre of 12-18mm, length, specific gravity 1.34 to 1.39, UV stable, alkali resistant with equivalent dia 15-40 micron, minimum tensile strength of 300 Mpa and at the rate as specified by the manufacturer. PQC laid, spread and compacted with mechanical means, including curing and tinning by texturing cum curing machine complete all as specified and directed. Required surface texturing to be done as specified in clause 10.1.14 and table 8 of IRC 15 2017, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Forming 20mm thick expansion joints filled with preformed bituminous filler and top 30mm prime and sealed with sealing compound grade "B" slab thickness 250mm, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Forming Contraction joints 30mm deep x 10mm wide grade A filled with sealing compound, complete all as specified and directed by Engineer-in-Charge.

Removing excavated material (soil) to a distance exceeding 250 Metre but not exceeding 500 Metre & depositing where directed at a level not exceeding 1.50 meter above the starting point, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing High density polyethylene 50mm dia pipes (HDPE) of pressure rating 6 Kgf/cm2 laid in trenches, complete all as specified and directed by Engineer-in-Charge.

Schedule 'A' E/M

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc., removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc., complete all as specified and directed by Engineer-in-Charge.

Taking down MCB DB including MCB of any type and size, complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Point wiring complete with 1.5 sqmm single core PVC insulated but unsheathed multi-stranded copper conductor FRLS cable 650/1100 Volts grade drawn through and including non-metallic rigid PVC heavy duty concealed conduit (minimum 20mm dia external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR Part-1, ISI marked with wall thickness not less than 1.8mm including conduit accessories like bends, tees, junction boxes etc., fixed concealed/ recessed in wall or ceiling etc., including 1.5 Sqmm PVC insulated but unsheathed multi-stranded copper conductor FRLS cable as earth continuity wire including modular type metal flush box with cover plate and frame of required module for mounting of modular switches, sockets, switch sockets, fan regulators with required modules, etc., complete all as specified and directed by Engineer-in-Charge. for the following:-

One light / fan point controlled by one, one way switch

One 3 pin 6 Amps socket outlet on same board

One 3 pin 6 Amps socket outlet on independent board .

Material & Labour for Point wiring complete with 2.5 sqmm single core PVC insulated but unsheathed multi-stranded copper conductor FRLS cable 650/1100 Volts grade drawn through and including non-metallic rigid PVC heavy duty concealed conduit (minimum 20mm dia external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR Part-1, ISI marked with wall thickness not less than 1.8 mm including conduit accessories like bends, tees, junction boxes etc., fixed concealed/ recessed in wall or ceiling etc., including 1.5 sqmm PVC insulated but unsheathed multi-stranded copper conductor FRLS cable as earth continuity wire including modular type metal flush box with cover plate and frame for modular switches, sockets, switch sockets for one 3 pin 15 or 16 Amps on independent board with required modules all as specified. insulated but unsheathed multistrand copper conductor FRLS cable 650/1100 Volts grade conforming to IS-694 drawn through PVC conduit (minimum 20mm dia (external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR Part I) ISI marked with wall thickness not less than 1.8 mm heavy duty including conduit accessories concealed pressed steel terminal boxes of size cover white/coloured including 1.5 Sqmm PVC insulated but unsheathed copper conductor FRLS cable as earth continuity wire for one 3 pin 15 or 16 Amps socket outlet on independent board, complete all as specified and directed by Engineer-in-Charge. Note:- Cost of cutting / chasing on wall and making good after repair deemed to be included in unit Rate

Material & labour for Point wiring complete with 4 sqmm single core PVC insulated but unsheathed multi-stranded copper conductor FRLS cable 650/1100 Volts grade drawn through and including non-metallic rigid PVC heavy duty concealed conduit (minimum 20mm dia external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR Part-I, ISI marked with wall thickness not less than 1.8mm including conduit accessories like bends, tees, junction boxes etc., fixed concealed/ recessed in wall or ceiling etc., including 4 sqmm PVC insulated but unsheathed multi-stranded copper conductor FRLS cable as earth continuity wire including modular type metal flush box with cover plate and frame for modular switches, sockets, switch sockets for one 3 pin 15 or 16 Amps on independent board with required modules all as specified. insulated but unsheathed multistrand copper conductor FRLS cable 650/1100 Volts grade conforming to IS-694 drawn through PVC conduit (minimum 20mm dia (external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR Part-I) ISI marked with wall thickness not less than 1.8mm heavy duty including conduit accessories concealed pressed steel terminal boxes of size cover white/coloured including 1.5 Sqmm PVC insulated but unsheathed copper conductor FRLS cable as earth continuity wire for one 3 pin 15 or 16 Amps AC socket outlet on independent board, complete all as specified and directed by Engineer-in-Charge. Note:- Cost of cutting / chasing on wall and making good after repair deemed to be included in unit Rate

Supply & fixing modular switch 1 way, 6 Amps, 1 module (ISI marked), complete all as specified and directed by Engineer-in-Charge.

Supply & fixing modular switch 1 way, 16 Amps, 1 module (ISI marked), complete all as specified and directed by Engineer-in-Charge.

Supply & fixing modular socket, 6 Amps, 2/3 pin combined 2 modules (ISI marked), complete all as specified and directed by Engineer-in-Charge.

Supply & fixing modular socket, 6/16 Amps, 2/3 pin combined 2 modules (ISI marked), complete all as specified and directed by Engineer-in-Charge.

Supply & fixing modular fan regulator, 120 watt, 2 module (ISI marked), complete all as specified and directed by Engineer-in-Charge.

Supply & fixing ceiling rose, surface Bakelite, 65 x 17 mm three terminals (ISI Marked), complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement LED tube light along with fixture, 20 W, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement LED decorative light along with fixture, 16 W square 170cm x 170cm, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC), complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Distribution Board single phase and neutral 12 way with standard bus bar, Din bar, etc., Double door, complete all as specified and directed by Engineer-in-Charge. Note:- Cost of cutting and modification in False ceiling deemed to be included in unit rate.

Supply and fixing VTPN 4 ways with standard bus bar, Din bar, etc., Double door, complete all as specified and directed by Engineer-in-Charge. Note:- Cost of cutting, chasing and making good matching with existing surface quoted rate deemed to be included in unit rate.

Supply and fixing MCCB 160 Amps, TPN, breaking capacity 25 KA, 415 V including connecting the cables with proper lugs and glands, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing MCB SPN 32 Amp 240 volt, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing MCB SP 6 to 32 Amp 240 volt, complete all as specified and directed by Engineer-in-Charge.

Material & labour for Sub main wiring with two runs of 6.0 Sqmm single core PVC insulated but unsheathed multi-stranded copper conductor FRLS 1100 Volts grade cable, fire retardant low smoke drawn through and including PVC concealed conduit heavy duty grade ISI marked 25mm dia (external) but shall be increased as per actual site requirement in accordance, with wall thickness not less than 1.8mm complete with all necessary fitting and including with conduit accessories and one run of 4.0 Sqmm single core PVC insulated but unsheathed multi-stranded copper conductor 1100 volts grade cable fire retardant low smoke as earth wire conductor, fixed on wall/ceiling including taking down old unserviceable sub main wiring, complete all as specified and directed by Engineer-in-Charge. Note :- Cutting chases for fixing of concealed conduit will measured and paid separately.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc. 10 cm girth, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole, 10 Amp MCB, complete all as specified and directed by Engineer-in-Charge.

Earthing complete with galvanised steel earth plate electrode 60cm × 60cm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less ‘than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion, including taking down old unserviceable earthinh, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Exhaust fan, steel body, AC single phase, 230 Volts, of size 300mm sweep with blades, frame and louvers including 3 core flexible copper cable of size 1.5 Sqmm connect from exhaust fan to ceiling rose, complete all as specified and directed by Engineer-in-Charge.

K B N TRADERS (BID ID -3391745)

Jayesh D Salet (BID ID -3390374)