PROVN OF TOILETS NEAR OFFRS SINGLE ACCN AND GUN PARK, SANITARY BLOCK NEAR BLDG NO. 106, BICYCLE CUM SCOOTER STAND AND 02 X STORE ROOM AT MIL STN DHRANGADHRA

Amount

Surface excavation not exceeding 30cm and averaging 15 cm deep and getting out in hard and dense soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in soft/disintegrated rock complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in hard/dense soil complete all as specified and directed.

Excavating in trenches not exceeding 1.5m wide and exceeding 1.5 m but notin depth for foundation of pole, laying of cables etc in hard/dense soil and getting out.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil complete all as specified and directed.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in soft/disintegrated complete all as specified and directed.

Excavation in post holes (or similar holes) each not exc 0.5 cum, getting out, in hard/dense soil including returning, filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25 cm, watering and removing surplus soil to a distance n.exc 50m and making good surfaces complete all as specified and directed.

M&L for providing dry river sand as in sand cushioning to UG cable including punning gently all as directed. Note: Depth after punning shall be measured and paid.

Removing excavated material (soil), not exceeding 50m and depositing where directed at level not exc 1.5m above the starting point complete all as specified and directed.

Removing of excavated material exc 500m but n.exc 1.0km and depositing where directed.

M&L for hard core of gauge not exc. 63mm deposited spread and levelled in layers not exc. 15 cm thick, spread, levelled and rammed to a true surface including watering complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for plain cement concrete (1:4:8) type D2 using 40 mm graded stone aggregate in foundation filling and mass concrete complete all as specified and directed.

M&L for plain cement concrete (1:5:10) type E-2 using 40 mm graded stone aggregate as in filling in sunken floors etc. complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B-2, using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed. Note:- Volume of column embedded in PCC shall be deducted for payment purpose.

M&L for cement concrete (1:2:4) type B2, using 40 mm graded stone aggregate as in surface channels and drains, benching, haunching etc. complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in coping and the like including necessary form work, all as specified and directed.

M&L for Pre-cast cement concrete (1:2:4), type B1, using 20mm graded stone aggregate, solid block in kerb stone of size 300mm x 300mm x 75mm, with plain fair faces, including chamfers, weathering, throating etc and set in cement mortar (1:4) complete all as specified and directed.

M&L for reinforced cement concrete, (nominal mix), type B1, 1:2:4 using 20mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for reinforced cement concrete, (nominal mix), type B1, 1:2:4 using 20mm graded stone aggregate as in chajjas complete all as specified and directed.

M&L for reinforced cement concrete, (nominal mix), type B1, 1:2:4 using 20mm graded stone aggregate as in beams, cantilevers, bressumers, lintels over 1.5m span complete all as specified and directed.

M&L for reinforced cement concrete, (nominal mix), type B1, 1:2:4 using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for reinforced cement concrete, M-20 (design mix) using 20mm graded stone aggregate as in foundation, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. basement slabs and mass cocrete complete all as specified and directed.

M&L for reinforced cement concrete, M-25 (design mix) using 20mm graded stone aggregate as in foundation, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. basement slabs and mass cocrete complete all as specified and directed.

M&L RCC M-25 (Design mix) using 20 mm graded stone aggregate as in chajja etc complete all as specified and directed.

M&L RCC M-25 (Design mix) using 20 mm graded stone aggregate as in beam, cantilevers, bressumers, lintels over 1.5m span complete all as specified and directed.

M&L for water proofing treatment to existing non-accessible roof slabs by providing 10mm thick bedding layer of cement morter (1:3) mixed with water proofing compound as per manufacturer's instruction and applying one coat of bituminous/polymerized primer confirming to IS-3384 @ 0.30 Ltr/Sqm and laying of actetic polypropylene (APP) modified membrane pre-fabricated, reinforced with non-woven polyester of 3.50Kg/Sqm (minimum), 3mm thick (minimum), with minimum 75mm side overlaps and 100mm end overlaps and applying one coat of bituminous aluminium paint over APP membrane complete including taking down existing water proofing treatment with bedding layer of cement mortar complete and removal of debries out side MD land all as specified and as directed. Note:- Supply only water proofing compound shall be measured and paid separately.

Supply only, integral water proofing compound.

M&L for Brick work with old size, sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with old size, sub class 'B' bricks, straight or curved on plan any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

Supply and laying, sub class old 'B' burnt bricks, size of brick 230x115x75mm, laid as cable protection cover complete all as specified and directed.

M&L for walling of random rubble stone masonry, uncoarsed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto course with maximum depression on face from straight edge held against the dressed surface not.exc. 20mm for sand stone complete all as specified and directed.

M&L for Form work to sides of concrete foundations, footings, base of columns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams etc for rough finished flat surfaces complete all as specified and directed.

M&L for form work to soffit of suspended slabs such as roof slabs, floor slabs, landings and simillar works not exceeding 20cm thick and fair finished surfaces of concrete all as specified and directed.

M&L for form work to chullah hoods, chajjas , troughs and simollar items including edges and fair finished surfaces of concrete all as specified and directed.

M&L for form work to sides and soffit of floor or roof beams, beams haunchingss, girders, brussummers, lintels, cantilevers, shelves including sup-ports, overhangs, etc and rough finished surfaces of concrete all as specified and directed.

M&L for form work to sides of pillars, posts, struts, piers, columns and stanchions and rough finished surfaces of concrete all as specified and directed.

M&L for formwork to edges of concrete flats, treads, break in floors, window cills, concrete wall, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping or similar work exc 10 cm but n exc 20 cm wide and fair finished surface completed all as specified and directed.

S&F 35 mm thick, 2nd class hard wood factory made, plain, framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F, factory made 30mm thick flush shutters, solid core construction, with block board core and plywood face panles, commercial type on both sides complete all as specified and directed.

S&F, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specifications complete all as specified and directed.

S&F, Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and directed.

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 200 mm and fixed complete all as specified and directed

S&F, Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 300 mm and fixed complete all as specified and directed.

S&F, butt hinges, medium weight, cold rolled, mild steel of size 100 mm complete all as specified and directed.

S&F, 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F, Mild steel pressed handles of size 150mm, oval type, stove enamelled black complete all as specified and directed.

S&F, 150mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel springcomplete all as specified and directed.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars, shouldered and/or riveted, or forged into spikes, framed guard bars etc and similar work conforming to Fe-290 (Gde-E-165) including applying one shop coat of red oxide primer complete all as specified and directed

S&F mild steel screw bolts 11 to 15mm dia (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exc. 5cm long complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for mild steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for mild steel TMT bars, 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bend to shape required and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for MS rolled sections (Fe 410-W (Gde-E-250) quality-A) as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates

S&F, mild steel work in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes without any attachment conforming to Fe-290 (Gde E-165) complete all as specified and directed. complete all as specified and directed.

S&F, MS angle iron Fe-410-W (Gde-E-250) quality A in framed work for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc complete all as specified and directed.

M&L for rolled mild steel angle iron work as in door frames complete, drilled for fixing of hinges etc. also fastening and fixing conforming to Fe-290 (Gde-E-165) complete all as specified and directed.

S&F, factory made steel windows with side hung shutter including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded including applying one shop coat of red oxide primer complete all as specified and directed.

S&F, factory made steel windows with side hung shutter including box type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded including applying one shop coat of red oxide primer complete all as specified and directed.

S&F, factory made steel ventilators with top hung shutter including hinges, steel peg stay, glazing bars including applying one shop coat of red oxide primer all as specified and directed

S&F, pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F, pre-painted galvalume aluminium zinc coating GI based plain steel sheet, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F, in repair, false ceiling, at any height, 600 x 600mm grid with Armstrong 'Prelude XL 32' grid system and 16mm thick mineral fibre acoustic tile 'RH - 99 Classic lite' with suspension system complete all as specified and per manufacturer's instruction. Make : Armstrong or equivalent as approved by GE.

M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg/sqm including cleaning the surface complete all as specified and directed.

M&L for 50mm thick cement concrete (1:3:6) type C1, using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

M&L for 75 mm thick cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate as in sub base of flooring/hard standing, path and finishing the surface even and fair without using extra cement complete all as specified and directed.

M&L for 50mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in floors and fixing of glass dividing strips, finishing the surface even and smooth with using extra cement complete all as specified and directed.

Glass dividing strips, 3mm thick and width of strip 38mm, inserted in position and conform to design complete all as specified and directed.

M&L for Coloured glazed ceramic tiles of size 300 x 200 x 7mm thick, on vertical wall surface, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 350 x 250 x 7mm/ 450mm x 350mm x 7mm on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including cement plaster 10mm thick in cement mortar (1:4) , complete all as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L, for machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658- 2006 of 60mm thickness, M-35 grade including 25mm thick sand cushion below paver blocks complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:4) on walls/ floors surfaces mixed with using water proofing compound @ 3% by weight of cement or as per manufacturer instructions, finished even and smooth without using extra cement to receive WPT complete all as specified and directed. Note:- Supply only water proofing compound shall be measured and paid separately.

M&L for rendering 15mm thick in cement mortar 1:6 on stone masonry surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick cement plaster 1:4 on stone masonry surface or surface other than fair face of brickwork surface finished even and smooth without using extra cement.

M&L for rendering 20mm thick cement plaster 1:4 on stone masonry surface or surface other than fair face of brickwork surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing new plastered or un-plastered walls surfaces and applying three coats white wash complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coat of cement base paint over a coat of white cmement putty complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of white cement as primer complete all as specified and directed.

M&L for preparing new plastered or un-plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M&L for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc. 0.5sq.m in each pane complete all as specified and directed.

M&L for 3mm thick figured glass, ordinary quality and glazing with oil putty in square not exc.0.5 sq.m in each pane complete all as specified and directed.

M&L for preparation of new wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 15mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 20mm bore of pipe complete all as specified and directed.

S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 25mm bore of pipe complete all as specified and directed.

S&F, chromium plated over head shower 100mm dia round shape single flow (ABS body chrome plated with Gray face plate) with rubit cleaning system complete all as specified and directed as per Cat No. EOS-542N of ESSCO or equivalent make approved by GE from the make specified in Appx 'C'.

S&F, 32mm bore, low density polyethelene pipe (HDPE) of pressure rating 6kgf/sq.cm fixed to walls, ceilings or in floors etc. complete all as specified and directed.

S&F, 40mm bore high density polythene pipes (HDPE) of pressure rating 6 Kg/Sqcm fixed complete to walls, ceiling or in floors etc.

Supply, hoisting, fixing in position and connecting, 500 litres capacity rotational moulded polyethylene water storage tank double layered (cylindrical, vertical with closed top), ISI marked, including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size and 20mm dia PTMT ball valve all as specified in SSR Part-I complete all as specified and directed.

Supplying, hoisting, fixing in position and connecting, 1000 litres capacity rotational moulded polyethylene water storage tank (cylindrical, vertical with closed top) including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size all as specified in SSR Part-I complete all as specified and directed.

S&F, bib taps, cast copper alloy, fancy type, chromium plated, screwed down, screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and directed.

Supply only, pillar tap, cast copper alloy with capstan head, chromium plated, screwed down high pressure, with or without lettered 'hot' or 'cold' with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and directed.

Supply only, pillar taps cast copper alloy with capstan head, chromium plated, fancy type, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and directed.

S&F, stop valves, fancy type, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed.

S&F, 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed.(Minimum weight -210 Gms)

S&F, waste coupling of PTMT (half or full threaded) minimum weight 45gms of 32mm bore of discharge pipe suitable for urinals complete all as specified and directed.

S&F, in repairs, towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all asa specified and directed.

S&F, PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F, 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or floor complete all as specified and directed.

S&F, 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or floor/walls complete all as specified and directed.

S&F, 75mm bore PVC (SWR) bend, any radius, with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR) bend, any radius, with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR) branch piece, single(Single Y) equal or unequal complete all as specified and directed.

S&F, 75mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR), vent cowl complete all as specified and directed.

S&F, PVC (SWR) floor trap, with chromium plated grating including jointing with solvent cement, dia of outlet 75mm complete all as specified and directed.

S&F, PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested for 150mm bore of pipe complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested for 200mm bore of pipe complete all as specified and directed.

M&L for salt glazed stone ware drain pipes, 150mm internal diameter, grade 'A' laid in trenches and jointed complete all as specified and directed.

M&L for salt glazed stoneware drain pipes, 200mm internal diameter, grade 'A' laid in trenches and jointed complete all as specified and directed.

Cutting into existing manholes for connecting new drain pipes, making good to pipes and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cment concrete (1:2:4) type B1, using 20mm graded stone aggregate, smooth finished and reforming benching as required for 150mm bore of pipe complete all as specified and directed.

Cutting into existing manholes for connecting new drain pipes, making good to pipes and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cment concrete (1:2:4) type B1, using 20mm graded stone aggregate, smooth finished and reforming benching as required for 200mm bore of pipe complete all as specified and directed.

S&F, in repairs, vitreous china squatting pan, 'Orissa’ pattern, white of size 580mm x 440mm with integral foot rest, P or S trap (excluding flushing cistern and flush pipe) including plain cement concrete (1:5:10) type D-2 using 40 mm graded stone aggregate as in filling in sunken portion etc. complete all as specified and directed.

S&F, vitreous china squatting pan, 'Orissa pattern, white of size 580mm x 440mm with integral foot rest, P or S trap (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F, 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brackets and connection to pipe or lever etc. complete all as specified and directed.

S&F, in repairs, vitreous china wash basin, white, flat back of size 550mm x 400mm including waste fitting and brackets grouted in cement mortar 1:2 in wall complete all as specified and directed. Note :- Supply only pillar taps, waste fittings, PVC connection, PVC waste pipe shall be measured and paid separately.

S&F in repair, vitreous china bowl urinal flat back, of size 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing flush pipe grating and union for discharge pipe and spreader with pipe (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F, in repair, vitreous china wash down water closet pan (Pedestal pattern), white with 'p' or 's' trap (excluding flushing cistern and flush pipe), including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc. with seat and cover complete all as specified and directed.

S&F, in repairs, brass chromium plated shower rose with or without swivel joint, 125mm size complete all as specified and directed.

S&F, in repair, Soap dish, vitreous China white, approximate size 160x 160x90mm any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F, 32mm dia High density poythelyne (HDPE) pipes of pressure rating 6kgf/sqm as in waste pipe for urinal, sink, etc

M&L for wiring with and including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawing through in and including medium grade, rigid non metallic PVC concealed conduit of 20mm bore and including cutting chases for conduits and sinkings for boxes, its accessories and including with multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire terminating with new modular sunken concealed terminal boxes complete all as specified and directed for the following :-

(a) One light/fan point controlled by one switch

(b) One multi pin socket 5 Amps, on the same board controlled by another switch.

(c) One multi pin socket 5 Amps, independent complelete all as specified and directed.

M&L for wiring with and including multi stranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed, FRLS cable, 1100 volts grade, ISI marked with valid CML number drawing through in and including medium grade, rigid non metallic, PVC concealed conduit of 20mm bore and including cutting chases fro conduits and sinkings for boxes, ties accessories and including with multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire terminating in and including new modular sunken concealed terminal boxes with cover plates complete all as specified and directed.

M&L for wiring with and including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawn in and including medium grade PVC casing and capping double lock type 32mm in size, fire resistant, ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box with 3mm thick industrial laminated sheet cover for mounting switches, sockets and fan regulators etc. complete all as specified and directed for the following :-

(a) One light/fan point controlled by one switch

(b) One 3 pin, 5 Amps, socket outlet on the same board controlled by another switch.

S&F, lamp holder, PVC/Polycarbonate, with back plate suitable for batten fittings complete all as specified and directed

S&F, switch piano, flush button, single pole, one way, 5 Amps complete all as specified and directed

S&F, switch piano, flush button, single pole, one way 15 Amps complete all as specified and directed

S&F, socket outlet, 2 in 1, 3 pin, 15 Amps and 5 Amps flush type complete all as specified and directed

S&F, socket outlet, 2 in 1, 3 pin, 5 Amps, flush type complete all as specified and directed

S&F, in repairs, sheet metal distribution board, SPN, 2 way 240 Volt, double door factory made and tested complete, protection class IP-42 suitable for mounting MCBs, isolator with 200 A tinned copper bus bar complete all as specified and directed

S&F, in repairs, sheet metal distribution board, factory made and tested complete, protection class IP-42 suitable for mounting MCBs, isolator with 200 A tinned copper bus bar of capacity 200 Amps of SPN, 4 way 240 Volt complete all as specified and directed

S&F, ceiling rose, 3 terminal , any shade, of PVC/Polycarbonate, isolated body complete all as specified and directed

Supplying and laying, GI pipe, 40mm dia, light grade, laid under road, fixing to poles / walls with necessary clamp and taking out existing unserviceable pipe complete all as specified and directed.

Supplying & laying, in repairs, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire heavy duty underground cable with aluminium multi stranded conductor, 1100 volt grade, laid in trenches/duct, passing through pipe/duct or fixed on pole and connecting and testing complete including taking down old unserviceable cable all as specified and directed of 6 Sqmm, 2 core sizes of cable.

Supplying & laying, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire heavy duty underground cable with aluminium multi stranded conductor, 1100 volt grade, laid in trenches/duct, passing through pipe/duct or fixed on pole and connecting and testing complete including taking down old unserviceable cable all as specified and directed of 50 Sqmm, 3.5 core sizes of cable.

S&F, in repair, angle holder, alongwith 12 Watt LED bulb complete all as specified and directed. Make of bulb : Wipro/Syska/Bajaj

S&F, Exhaust Fan, 250mm Sweep, single phase, 230/240 volts, 50 Hz, including making opening for exhaust fan including grouting nut , bolts and washer for fixing of fan and making good the disturbed surfaces all as per existing and mounting fan including connected with three core copper conductor cable 0.75mm complete all as specified and directed .

S&F, miniature circuit breakers, (MCB), type curve ‘B’ , SP, 6 to 32 Amps complete all as specified and directed.

S&F, miniature circuit breakers (MCB), single pole and neutral type ‘B’, 32-40 Amps 240 Volts complete all as specified and directed.

S&F, miniature circuit breakers, (MCB), type curve ‘C’, SPN, 32 Amps, 240 V complete all as specified and directed.

S&F, in repairs, LED light fitting, batten type, housed in extruded from powder coated aluminium, 9 watt for soft diffuser lighting with and including lamp and connecting up complete with white PVC insulated and PVC sheathed round flexible three core copper conductor cable of suitable size and testing on completion all as specified and directed. Make: As per Cat No. BAJAJ LED BATTEN 9W (Item Code 830102) of Bajaj or equivalent make approved by GE from the make specified in Appx 'C'.

S&F, LED oval bulk head, 10 watt complete all as specified and direccted.

S&F, LED light fitting, batten type, 20 Watt housed in extruded from powder coated aluminium, and connecting up complete with PVC sheathed round flexible three core copper conductor cable of suitable size and testing on completion all as specified and directed.

S&F, in repairs, sub-main wiring with 2 single core, 4 Sqmm PVC insulated, unsheathed, 1100 Volts grade, FRLS, copper multi stranded conductor drawn in and including PVC concealed conduit and conduit acessories including drawing one run of PVC insulated, unsheathed, 1100 Volts grade, FRLS, copper conductor multi stranded, 2.5 Sqmm size as continuous earth wire drawn through and connected to main switch/DB and testing on completion complete all as specified and directed. Note: (i) 2 runs of main conductor, one run of earth conductor and one run of PVC conduit and acessories shall be measured as one unit length.(ii) Rate quoted shall deemed to includes cuttings chases for consealing PVC conduit and making good the disturbed surfaces in CM 1:3 complete.

M&L,earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6mm thick buried directly in ground [earth pit not less than 2.25 metre deep below normal ground level] with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized earth wire of 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of MES SSR Part I all as specified and testing on completion including provision of earth lead protected by 15 mm dia light grade GI pipe & watering pipe shall be 20 mm bore medium grade GI pipe including all excavation and earth work in any type of soil, PCC pit with RCC cover, char coal, salt, funnel etc complete. Note : Rate quoted by tenderers shall be deemed to include for following provisions;-[i]. Excavation & earth work in any type of soil including removing of surplus material upto 50 M.[ii]. PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50x50 cm with 8mm TMT bars @ 10 cm C/C both ways with handles.[iii]. Main earthing lead from earth electrode to test point upto 7.5 mtr.[iv]. Funnel with watering pipe [GI pipe] 20mm bore [ISI marked] medium grade & copper lugs, charcoal & salt as reqd.[v]. GI protection pipe of size 15 mm bore light grade 7.5m.

Bhumi Construction

AMI CONSTRUCTIONS