Loading
Loading…
Loading…
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
Tender Value
₹3.8 Cr
EMD Value
₹7.6 L
Closing Date
23 Oct 2026, 4:00 pm7d left
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
EXECUTIVE ENGINEER(R-I)
R-I Division Zonal Centre Tilak lane Tilak Marg New Delhi 110001
Supply and fixing open Gym equipments under New Delhi constituency (AC-40).
2026_NDMC_300090_1
34/EE(R-I)/2026-27 (E- 210687) 3rd Recall
Open Tender
Civil Works
Percentage
180 days
NDMC Area
Please refer Tender documents.
2 documents required · 2 mandatory
₹0
₹7.6 L
15 Oct 2026
15 Oct 2026
23 Oct 2026
15 Oct 2026
23 Oct 2026
15 Oct 2026
This is a percentage-rate BOQ. The schedule below shows estimated quantities and rates. Bidders quote a single percentage above or below the total estimated cost.
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1 | Supply and Fixing at required site, Air Walker with following specifications.
1. Dimensions (LxWxH): 1100 x 450 x 1300mm
2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.
3. ‘U’ shaped main frame of NB 80mm (G.I.) ‘C’ Class Pipe, Leg Support frame of NB 50mm (G.I.) ‘C’ Class Pipe.
4.Handle frame pipes of NB 32mm (G.I.) ‘C’ Class.
(‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters)
5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.
6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored.
9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury.
10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.
11. The equipment are fitted with inbuilt limiters to prevent unwanted movements.
12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.
13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.
14. High tensile steel with galvanized nut bolts are used for assembly.
15. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.
16. Self-Explanatory stainless steel label fixed on equipment for ease of use. All complete as per direction and entire satisfaction of Engineer-In-Charge. (Nothing extra shall be paid for cartage/loding/unloding and installation at site). | 23 | Each | 67,829.52 | ₹15,60,078.96 |
| 2 | Supply and Fixing at required site, Sit Up Station with following specifications.
1. Dimensions (LxWxH): 1500 x 1150 x 650mm
2. Fabricated with main frame of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.
3. Main frame of NB 25mm (G.I.) ‘C’ Class Pipe.
4. Leg support of NB 65mm (G.I.) ‘C’ Class Pipe.
(‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters)
5. Perforated MS Sheet for Back Support.
6. Fixed on its top is back support made of perforated MS sheet of 2mm thickness.
7. All pipes are powder coated using Akzo Nobel or equivalent Paint of 80-120 micron thick.
8. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
9. Zinc primer paint is applied at all welding points prior to finishing.
10. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.
11. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.
12. Once the concrete is set, the equipment is fixed on to it.
13. High tensile steel with galvanized nut bolts are used for assembly.
14. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.
15. Self-Explanatory stainless steel label fixed on equipment for ease of use. All complete as per direction and entire satisfaction of Engineer-In-Charge. (Nothing extra shall be paid for cartage/loding/unloding and installation at site). | 23 | Each | 56,755.31 | ₹13,05,372.13 |
| 3 | Supply and Fixing at required site, Air Swing with following specifications.
1. Dimensions (LxWxH): 1150 x 900 x 1250 mm
2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.
3. Leg Support frame of NB 50mm (G.I.) ‘C’ Class Pipe.
4. Handle support frame of NB 32mm (G.I.) ‘C’ Class Pipe.
(‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters)
5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.
6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Handle bars are provided with high end quality rubber grips.
9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.
10. Foothold made of MS Sheet Metal with rounded edges to prevent impact and injury.
11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.
12. The equipment are fitted with inbuilt limiters to prevent unwanted movements.
13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.
14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.
15. High tensile steel with galvanized nut bolts are used for assembly.
16. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.
17. Self-Explanatory stainless steel label fixed on equipment for ease of use. All complete as per direction and entire satisfaction of Engineer-In-Charge. (Nothing extra shall be paid for cartage/loding/unloding and installation at site). | 23 | Each | 60,908.13 | ₹14,00,886.99 |
| 4 | Supply and Fixing at required site, Horse Rider with following specifications.
1. Dimensions (LxWxH): 1000 x 600 x 1100 mm
2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make
3. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe.
4. Handle support frame of NB 50mm (G.I.) ‘C’ Class Pipe and other pipes of NB 32mm & NB 25mm (G.I.) ‘C’ Class Pipe.
(‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters)
5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.
6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.
9. Foothold made of NB 32mm (G.I.) ‘C’ Class Pipe.
10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly.
11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.
12. The equipment are fitted with inbuilt limiters to prevent unwanted movements.
13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.
14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.
15. High tensile steel with galvanized nut bolts are used for assembly.
16. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.
17. Self-Explanatory stainless steel label fixed on equipment for ease of use. All complete as per direction and entire satisfaction of Engineer-In-Charge. (Nothing extra shall be paid for cartage/loding/unloding and installation at site) | 23 | Each | 60,908.13 | ₹14,00,886.99 |
| 5 | Supply and Fixing at required site, Leg Press with following specifications.
1. Dimensions (LxWxH): 2000 x 550 x 1600 mm
2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.
3. Seat Main frame of NB 50mm (G.I.) ‘C’ Class Pipe and Pipe connecting main post to seat main frame of NB 65mm (G.I.) ‘C’ Class Pipe.
(‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters)
4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.
5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
6. Zinc primer paint is applied at all the welding points prior to finishing.
7. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.
8. Foothold made of NB 50mm (G.I.) ‘C’ Class Pipe.
9. Seats made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly.
10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.
11. The equipment are fitted with inbuilt limiters to prevent unwanted movements.
12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.
13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.
14. High tensile steel with galvanized nut bolts are used for assembly.
15. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.
16. Self-Explanatory stainless steel label fixed on equipment for ease of use. All complete as per direction and entire satisfaction of Engineer-In-Charge. (Nothing extra shall be paid for cartage/loding/unloding and installation at site) | 23 | Each | 74,750.89 | ₹17,19,270.47 |
| 6 | Supply and Fixing at required site, Pull Chair with following specifications.
1. Dimensions (LxWxH): 2000 x 550 x 1600 mm
2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.
3. Seat main frame of NB 50mm (G.I.) ‘C’ Class Pipe, Pipe connecting main post with handle frame of NB 65mm (G.I.) ‘C’ Class Pipe.
4. Handle frame of NB 32mm (G.I.) ‘C’ Class Pipe.
(‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters)
5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.
6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Handle bars are provided with high end quality rubber grips.
9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.
10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly.
11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.
12. The equipment are fitted with inbuilt limiters to prevent unwanted movements.
13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.
14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.
15. High tensile steel with galvanized nut bolts are used for assembly.
16. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.
17. Self-Explanatory stainless steel label fixed on equipment for ease of use. All complete as per direction and entire satisfaction of Engineer-In-Charge. (Nothing extra shall be paid for cartage/loding/unloding and installation at site) | 23 | Each | 94,130.75 | ₹21,65,007.25 |
| 7 | Supply and Fixing at required site, Seated Chest Press with following specifications.
1. Dimensions (LxWxH): 1800 x 700 x 2000 mm
2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.
3. Seat Main frame of NB 50mm (G.I.) ‘C’ Class Pipe.
4. Handle frame of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe.
(‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).
5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.
6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Handle bars are provided with high end quality rubber grips.
9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.
10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly.
11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.
12. The equipment are fitted with inbuilt limiters to prevent unwanted movements.
13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.
14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.
15. High tensile steel with galvanized nut bolts are used for assembly.
16. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.
17. Self-Explanatory stainless steel label fixed on equipment for ease of use. All complete as per direction and entire satisfaction of Engineer-In-Charge. (Nothing extra shall be paid for cartage/loding/unloding and installation at site) | 23 | Each | 94,130.75 | ₹21,65,007.25 |
| 8 | Supply and Fixing at required site, Arm Wheel with following specifications.
1. Dimensions (LxWxH): 850 x 800 x 1800 mm
2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.
3. Wheel frame of NB 32mm with connecting spokes of NB 25mm, Pipe connecting main pillar with wheel frame of NB 50mm. All pipes must be (G.I.) ‘C’ Class Pipes.
(‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).
4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.
5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
6. Zinc primer paint is applied at all the welding points prior to finishing.
7. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.
8. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.
9. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.
10. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.
11. High tensile steel with galvanized nut bolts are used for assembly.
12. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.
13. Self-Explanatory stainless steel label fixed on equipment for ease of use. All complete as per direction and entire satisfaction of Engineer-In-Charge. (Nothing extra shall be paid for cartage/loding/unloding and installation at site) | 23 | Each | 56,755.31 | ₹13,05,372.13 |
| 9 | Supply and Fixing at required site, Elliptical Exerciser with following specifications.
1. Dimensions (LxWxH): 1200 x 550 x 1600 mm
2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.
3. Main frame of NB 80mm (G.I.) ‘C’ Class Pipe.
4. Handle frame of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe.
(‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).
5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.
6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Handle bars are provided with high end quality rubber grips.
9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.
10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.
11. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.
12. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.
13. High tensile steel with galvanized nut bolts are used for assembly.
14. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.
15. Self-Explanatory stainless steel label fixed on equipment for ease of use.
16. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury.
All complete as per direction and entire satisfaction of Engineer-In-Charge. (Nothing extra shall be paid for cartage/loding/unloding and installation at site) | 23 | Each | 63,676.68 | ₹14,64,563.64 |
| 10 | Supply and Fixing at required site, Double Cross Walker with following specifications.
1. Dimensions (LxWxH): 1600 x 600 x 1600 mm
2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.
3. Handle main frame of NB 50mm and other connecting pipes of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe.
(‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).
4. Foot support frame of 96 x 46 x 3mm MS rectangular pipe.
5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.
6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored.
9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury.
10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.
11. The equipment are fitted with inbuilt limiters to prevent unwanted movements.
12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.
13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.
14. High tensile steel with galvanized nut bolts are used for assembly.
15. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.
16. Self-Explanatory stainless steel label fixed on equipment for ease of use. All complete as per direction and entire satisfaction of Engineer-In-Charge. (Nothing extra shall be paid for cartage/loding/unloding and installation at site) | 23 | Each | 84,440.82 | ₹19,42,138.86 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 1.54 MB
BOQ_400489.xls
BOQ • 0.35 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .