Lift Irrigation HT Maintenance Work-Urgent Conversion of 11 KV DHT service connection in to 11 KV HT at Karukapilly LIS Under Electrical Lift Irrigation section Ramamangalam.

Amount

HT Work

OD190538/2022-2023:Supply and erection of two pole structure consisting of 2 nos 11 mtrs long 175x85 RSJ poles and fixing the pole including excavation of trench and providing PCC of 1:3:6 mm of 40mm metal at bottom and RCC 1:2:4 of 20 mm metal at top with size 600x600x1980 mm and neatly plaster over the earth portion of plint and neatly painted the pole with 2 coat epoxy paint over a coat of primer as required.

13.1:Supplying and erection of galvanised stay set for 11 KV over head lines complete with 19/ 20 mm dia X 1.8 metres long stay rod, anchor plate of size 45 cm X 45 cm X 7.5 mm thick, thimble, stay clamps, turn buckle ( 20 mm X 600 mm ), 7/ 4.00 mm dia G.I. stay wire and 11 KV strain insulator etc in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size ) foundation including excavation and refilling etc. as required.

OD190539/2022-2023:Supply and fixing of channel iron 100mm X 50 mm X 6 mm (9.56 kg per metre) for placing and fixing CT-PT unit / ABS/ Lightning arrestor using suitable size bolt and nuts , paintin 2 coat epoxy paint over primer, as per directions of departmental officers

OD190540/2022-2023:Supply, conveyance, fitting and commissioning of approved make 11 KV,400 Amps, out door type gang operated, Polymer type Air Break triple pole switch with all necessary accessories including adequate length of GI pipe as operating lever, operating handle with insulation and locking arrangements on suitable height, with necessary clamps, nut, bolt, washer etc. as required.

90.3.17.3:Supply, conveyance and erection of the following sizes of 'B' class GI pipe in single section for post top lantern of all types on concrete base (excluding charges for concrete base and excavation) and painting with 2 coats of synthetic enamel paint over a coat of zinc chromate primer etc. as required.50 mm dia GI pipe

13.10:Supplying and erection of 11 KV pin insulator complete with large steel head G.I. pin, nuts, washers etc. as required

13.11:Supplying and erection of 11 KV disc insulator for 11 KV over head lines with galvanised insulator fittings, ball and socket type and complete with galvanised strain clamps, bolts, nuts, washers etc. as required.

13.13:Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire. 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharge current rating of 5 KSA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required.

90.16.1.8:Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required8.00 mm copper conductor (0 SWG)

90.16.5.8:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.8 mm (0 SWG)

OD190542/2022-2023:Supply, conveyance, fitting and commissioning of approved make 11 KV, Drop Out Fuse Unit with all standard accessories GI / MS chanel, properly fixing on cross arm including giving connections etc. as required.

OD24240/2025-2026: Supply, installation, convoyance, errection, testing and commissioning of Outdoor type panel with 11kV, 630A, 26.3kA for 3 sec Horizontal Draw out VCB fitted with Manual cum Motor operated spring charging mechanism with 230V AC motor and motor control switch, shunt trip coil of 24V DC, closing coil of 24V DC, Auxiliary Contact 2NO + 2NC, Mechanical ON/OFF indicator, mechanical operation counter, protection CT, (--/5A, 5P10, 15VA , 11kV/110V, Cl-0.2, 25VA PT Instantaneous IDMT relay with Microprocessor based 3O/C + and 1EF Protection relay, Strip Heater with thermostat, Digital Ammeter and Digital Voltmeter, Power pack 230V AC-24 V DC emergency OFF push button with HT Metering (3nos CT & 1 no PT Unit ), Provision for TOD Meter.

OD190544/2022-2023:Supply, conveyance, errection testing and commissioning of approved make 3 phase, 4 wire, 110 V ( L-L), -/1 A CT or -/5A CT with DLMS compliant, having RS 485 port of class 0..2 S class TOD meter in the existing meter box after submitting the test certificate from KSEB TMR Division, giving all connections etc. as required. (excluding testing fees)

OD25666/2025-2026:Supply and laying of 3 core 300 sq.mm 11KV stranded compact circular aluminium conductor, conductors screened with extruded semi conducting compound XLPE insulated, insulation screened with extruded semi conducting compound in combination with copper tape (0.3KA for I sec.) cores laid up. inner sheath of PVC ape, galvanized steel flat strip armored, and overall PVC sheathed cable conforming to IS: 7098 part II 1985 with latest amendments, on existing GI cable trays

10.5.4:Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :300 sq. mm

90.12.12.7:Supply & laying of DWC pipe in ordinary soil 1.2 m below ground level including excavation120/102.5 mm or nearest size

14.13.2:Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required80 mm dia

OD24239/2025-2026:Supply, installation, testing and and commissioning of 400 KVA,11KV/433 V 3 phase 50 Hz copper wound out door type ONAN cooled transformer having vector group of Dyn 11 , cable box on LT side, Off circuit tapping's of +5% to -10 % in steps of 2.5 %, first fill of oil and standard fittings conforming to IS 1180 Level -1 specification. Intrans/Unitech or equivalent make

90.16.1.5:Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required4.75 mm copper conductor (6 SWG)

90.16.5.5:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.4.75 mm (6 SWG)

OD190546/2022-2023:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armored copper control cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , color washing etc. as required.12 core 2.5 sq mm with factory made clamp.

1.17.20:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.2 x 4 sq. mm

OD190552/2022-2023:Supply and fixing of wall fencing to the HT yard with appropriate area including(50mmx50mmx6mm size) angle iron support in all leg fixed with concrete base and(35mmx35mmx5)angle iron frame in the outer frame area of the each side of the fencing and (25mmx25mmx3mmsize) angle iron support in each side more than 1.2 meter interval and one door provided in the front side of the yard with the same material ,and all side of the fencing covered with weld iron net mesh with supported by 25*3 flat iron. All the structures are welded and fabricated using suitable nut and bolt , and painted 2 coats of epoxy paint over a coat of primer as required. The bottom of the fencing shall be 150 mm for which brick work 225 mm thick shall be around the fencing including plastering as required

OD190553/2022-2023:Providing rubble masonry work in cement mortar 1:8

OD190554/2022-2023:Reinforcement for R.C.C works, bend tied and placed in position (plain grill requiring bend cold) using tor steel

OD190555/2022-2023:supply and spreading of fine sand in HT yard

OD190556/2022-2023:Supply conveyance and laying 40 mm size broken stone in the ground of HT yard as required

OD190557/2022-2023:Supply conveyance and laying 20 mm size broken stone in the ground of HT yard as required.

14.1:Excavation for foundation in soft soil including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 metres.

14.7:Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc as required.

14.8:Providing and laying in position cement concrete 1 :3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc. including form work etc. as required.

14.11:Providing brick work (in width 225 mm or more) with F.P.S. bricks of class designation 7.5 in cement mortar 1:4 (1 cement : 4 coarse sand) at all levels.

14.12:Providing 15mm thick cement plaster of mix 1:4(1 cement: 4 fine sand) at all levels

2.22:Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

LT side work

OD236246/2022-2023:Providing and fixing 800 Amp TP&N disconnector fuse switch unit (suitable enclosure) with 630 A ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required.

90.12.7.36:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 300 sq mm

90.12.1.36:Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil).3.5 core 300 sq mm

9.1.30:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 300 sq. mm (70mm)

OD215717/2022-2023:Supplying and providing earth clamps made out of copper strips of the following sizes including cutting and bending the flat exactly to the shape of the gland, drilling necessary holes for nut & bolt, tinning the points of contacts and giving connections to the main earthing system as required.(25 x 3 mm for earthing glands of size 240 sq mm to 300 sq mm)

90.12.9.5:Supplying, laying and jointing of the following sizes of double wall corrugated (DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanical protection to underground power cables with all required accessories in ground in the existing trench90/75 mm or nearest size

OD216893/2022-2023:Supply, fixing testing and commissioning of suitable tye Standby lowset Earth fault relay L&T MC12AB50X00 or Equivalent

OD216894/2022-2023:Supply and Fixing of 150/5 A, 7.5 VA, accuracy class 10P 10, Protection CT (Tape wound)

90.14.8.11:800 A, 4 pole, manual draw out type, microprocessor based ACB with overload , instantaneous SC , delayed SC and ground fault protection 50kA

OD25616/2025-2026:Supply and installation of Shunt Release for 800A ACB

OD25592/2025-2026:Supply and fixing 800A 4Pole Spreader Terminals (4 Pieces) of L&T or equivalent make.

2.1.7:Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required.320 Amp TP&N

2.1.6:Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required.200 Amp TP&N

2.1.8:Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required.400 Amp TP&N

OD248085/2022-2023:Supply & fixing of 4 lock 2 key Castell key lock set for 100A to 800 A SDF

OD25593/2025-2026:Supply and installation of 2 Amps MCBs on a DIN channel in the existing Panel in place of control fuse for the protection of Indicators,Voltmeter,Ammeter etc as per the direction of Departmental staff at site.

OD26240/2025-2026:Supply and fixing 145A 3 pole Power contactor for 80HP motor starter AC3 rating at415v with Ac coil, Auxiliary contacts 2NO/NC (L&T or equivalent make)

OD26241/2025-2026:Supply and fixing 185A 3 pole Power contactor for 100HP motor starter AC3 rating at415v with Ac coil, Auxiliary contacts 2NO/NC (L&T or equivalent make)

OD26242/2025-2026:Direct Mounting Thermal over Load Relay for MNX110-140 power contactor amps range 70-110 A for 80 HP Squirrel cage induction motor (FASD)

OD26243/2025-2026:Supply of electronic timer for FASD(L&T ST 80329000 ) or equivalent

90.14.1.1:Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623.<br> Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc.Supply and fabrication of MV panel board using 2.00mm CRCA sheet, powder coated (excluding base frame)

90.14.2.2:Supply and providing 3mm SMC sheet as shrouding for bus interconnection / terminations etc. including required nut & bolt etc.

90.14.3.2:Supply and providing heavy duty 'A' section neoprene gasket in the panel boardU' section rubber beeding suitable for 1.60/ 2.00 mm sheet

90.14.5:Supply and fabrication conveyance and installation of angle iron frame work for wall mounting panel board

90.14.4:Supply and fabrication conveyance and installation of base frame of panel board using 75 x 40 mm rolled steel channel (ISMC)

OD28526/2025-2026:Supply and installation including all manner of supports/suspenders and anchor bolts etc. for cable trays made out of suitable size channels sections , slotted angles , flates , MS plates etc as including painting with 2 coats of synthetic enamel paint over a coat of zinc chromate primer , making good the damages , colour washing etc. as required.

90.14.6:Supply and providing copper bus bars including finger type SMC bus bar supports in the bus chamber, suitable size nut & bolt, providng heat shrink sleeves etc. as required.

90.14.7:Supply and providing copper earth bus in the panel board

OD216903/2022-2023:Supply and fixing of Multifunction meter to read: V, A, F, 3 phase accuracy class 1

OD231097/2022-2023:Supply and Fixing of 250/5 A, 5 VA, accuracy class 1, Resin Cast Metering CT

OD216904/2022-2023:Carrying out control wiring for panel with normal meters and indication lamps for interconnecting the control devices/ equipment's including providing suitable size insulated sockets at the termination points or soldered properly, providing numbering ferrules for the proper identification of the wiring, keeping the wiring firm by suitable tie/ tie mounts/ PVC duct etc as required.-1.50 sq mm single run with required sockets

OD216905/2022-2023:Supply and installation of LED indicators for power/on-off/trip-different Colours

OD216906/2022-2023:Supply & fixing Illuminated Flush head Actuator - Green with legend 'ON', (Contact - 1 NO)

OD216907/2022-2023:Supply & fixing Illuminated Flush head Actuator - Red with legend 'OFF', (Contact - 1NC)

OD216942/2022-2023:Supply and providing 2.0 mm thick Elastomeric fire retardant insulating mat as per IS 15652/2006 to withstand 3.3 KV dielectric strength

OD216943/2022-2023:Supply & fixing "Cable alley" 100 x 40 mm aluminium anodised legend plate

OD216944/2022-2023:Aluminium anodised Danger Notice Board of size 150 x 100 mm. with inscriptions (both in English and Malayalam) and conventional Skull and Bone in Red color

OD247954/2022-2023:Supply & fixing "Busbar chamber" 100 x 40 mm aluminium anodised legend plate

OD216945/2022-2023:Painting letters or figures of the following sizes with enamel paint as identification mark to SB, DB, panel board etc as required in Panel board/DB's- 2.50 cm, 4 cm or 5 cm height

90.12.7.1:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.2 core 4 sq mm with factory made clamp

9.1.1:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.2 X 6 sq. mm (19mm)

OD216990/2022-2023:Supplying and providing earth clamps for siemens/ tropodur type cable glands of suitable length and other dimensions noted along with each size of glands for the following sizes of cables as required.(4 sq - 16sq mm with 12 mm wide x 1.20 mm thick clip)

2.10.1:Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

OD247949/2022-2023:Supply and installation of Three phase Voltmeter (V - RY, YB, BR) of accuracy class 1

OD247950/2022-2023:Supply and installation of Three phase Ammeter (I - R, Y, B) of accuracy class 1

OD247951/2022-2023:Supply and Fixing of 400/5 A, 15 VA, accuracy class 0.5, Resin Cast Metering CT

OD247952/2022-2023:Supply and providing 11 KV rubber hand long glove

OD247955/2022-2023:Supply and Fixing of 800/5 A, 15 VA, accuracy class 0.5, Resin Cast Metering CT

OD247956/2022-2023:Disconnecting all the cable connections, earth connections etc. to the existing old panel board, detaching the incoming panel compartment after dismantling the bus bar connections, keeping the same in pump house yard.

OD26664/2025-2026:Alteration work for the existing old panel board for standardisation with adding New ACB module giving connection as required , dismantling the damaged switch gears, meters, CTs, relays and fuse units etc . Rearranging the panel position including necessary holes and cuttings concrete slabs if necessary as directed by offfice staff, also provide minor repairs and painting the entire panel board checking and testing all connections and make it into good working condition as pr direction from departmental staffs direction.

OD250872/2022-2023:Supply of LT grade rubber gloves

OD250873/2022-2023:Supply and providing 5 Kg. Dry Chemical Powder type Fire Extinguisher with hose and clamps including fixing it to wall as required.

OD250874/2022-2023:Supply and providing 9 Liter capacity GI Fire Bucket painted in post office red with primer coat of red oxide and written with white paint 'FIRE' mounted on MS angle frame work/ wall bracket filled with fine sand, painting the bracket/ floor stand including making good the damages, colour washing etc. as required.

OD250875/2022-2023:Supply and providing First Aid Chart duly framed and placed in a conspicuous location for clear vision.

OD250876/2022-2023:Supply of fuse puller up to 630 Amps

OD250877/2022-2023:Supply and providing First aid box with essential medicine, cotton, plaster, 1 no. scissors etc.

90.14.24.18:Supply & fixing the following Power Capacitors 3 phase delta connected in positon and giving connection.3 KVAr, 3 phase, 440 V, delta connected, standard duty Metalised Poly Propylene Capacitor, Box Type, suitable for direct connection to motors.

90.14.24.25:Supply & fixing the following Power Capacitors 3 phase delta connected in positon and giving connection.15 KVAr, 3 phase, 440 V, delta connected, standard duty Metalised Poly Propylene Capacitor, Box Type, suitable for direct connection to motors.

90.14.24.26:Supply & fixing the following Power Capacitors 3 phase delta connected in positon and giving connection.20 KVAr, 3 phase, 440 V, delta connected, standard duty Metalised Poly Propylene Capacitor, Box Type, suitable for direct connection to motors.

4.1.5:Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.375 mm width X 50 mm depth X 2.0 mm thickness

90.12.7.24:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3 core 240 sq mm

9.1.19:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 X 300 sq. mm (70mm)

OD26239/2025-2026:Supply and fixing following capacity switch fuse unit with ISI marked HRC fuses in sheet enclosure, making connections, etc. as required.315 amps TPN

OD26805/2025-2026:Supply and fixing 120 Sq.mm tubular copper socket

OD26834/2025-2026:Supply and fixing 150 Sq.mm tubular copper socket

Earthing

OD190531/2022-2023:Supply and providing plate earthing as per IS 3043 with 1200x1200x12 mm GI/CI earth plate, 50 mm GI watering pipe fixed to the earth plate with 25 x 3mm GI clamps, GI funnel with weld mesh, filling required quantity of charcoal including construction of inspection chamber with a bed concrete of 1:4:8 PCC using 40 mm broken stone (10 cm thick), brick work in cement mortar 1:6, plastering the surface of brick masonry and the exposed surface of PCC bed with cement mortar 1:4, 12 mm thick, (the finished inside dimension shall be 450 x 450 x 450 mm) but excluding test joint, earth continuity conductor to the plate, and covering at the top. (in ordinary soil)

5.4:Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

90.16.3.5:Supply and clamping the following size of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 X 3 mm GI flat duly painted or heavy duty GI spacer saddles spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required ( for horizontal run)32 x 6 mm GI strip

OD215021/2022-2023:Supply and providing earth lead from the test joint to the earth electrode using 6 SWG copper wire from test joint to earth electrode and fixing firmly with plate, test joint etc as required.

90.16.3.7:Supply and clamping the following size of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 X 3 mm GI flat duly painted or heavy duty GI spacer saddles spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required ( for horizontal run)50 x 6 mm GI strip

OD215150/2022-2023:Supply and clamping the following size of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 X 3 mm GI flat duly painted or heavy duty GI spacer saddles spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required ( for vertical run)50 x 6 mm GI strip

5.20:Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

90.16.1.5:Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required4.75 mm copper conductor (6 SWG)

90.16.5.5:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.4.75 mm (6 SWG)

OD190532/2022-2023:Supply and providing the following sizes of cast iron gully trap with covering at the top of the inspection chamber of earth pit as required . - 450 x 450 x 10 mm cast iron gully trap with covering

OD236228/2022-2023:Supply and laying 50 x 6 mm GI strip tinned at the points of contacts laid 0.60 m below ground level including excavating trench of suitable size and refilling etc. as required (in ordinary soil).

OD25644/2025-2026:supply and providing test joint for the earthing system using 50x6mmGI strips including cutting and bending and bend to shape drilling necessary holes and fixed to the watering pipe etc as required

OD25645/2025-2026:supply and providing earth lead from the test joint to the earth plate including 25 x3 mm copper strip including cutting drilling necessary holes and fixing firmly with plate test joint etc as required

OD28558/2025-2026:Supply and providing the 12 x 3mm sizes of Brass bolt and nut with washers on the existing MS box / earth bus etc. as required including drilling necessary holes as required

OD28559/2025-2026:Supply and providing the 25 x 6 mm sizes of Brass bolt and nut with washers on the existing MS box / earth bus etc. as required including drilling necessary holes as required

OD28560/2025-2026:Supply and providing the 25 x 3mm sizes of Brass bolt and nut with washers on the existing MS box / earth bus etc. as required including drilling necessary holes as required

90.16.2.1:Supply and laying of the following sizes of B class GI pipe laid 0.6 m below ground level including excavating trench of suitable size and refilling etc, as required.15.mm dia. G.I pipe ( medium class)

90.16.2.3:Supply and laying of the following sizes of B class GI pipe laid 0.6 m below ground level including excavating trench of suitable size and refilling etc, as required.32 mm dia G.I pipe ( medium class)

Supply ,Installation and Commissioning 5 HP Vacuum pump set

OD25291/2025-2026:Charges for providing vacuum pipeline for vacuum pump set by providing 25mm GI pipe ,GI bends, GI coupling ,hose collar, hose coupling, half turn valve, flexible hose necessary bolts and nuts etc complete with all industrial charges and labour charges

OD25292/2025-2026:Supply installation ,Testing and commissioning of vacuum pump model DV 40 with Del 40 mm X Suc 40 mm coupled to 3.7KW/5 HP,1450 RPM squirrel cage induction meter suitable for 3phase voltage supply kirloskar or equivalent make

KSEB , INSPECTORATE , Etc

OD26245/2025-2026: Charges for checking, Testing , all meters at KSEBL/inspectorate for approval etc as required (With actual bill)

Kittu Electricals private limited (BID ID -2223010)

Bidder Name

Kittu Electricals private limited

ELCON ELECTRICALS