PROVISION OF ANNEXE BUILDING AND OTHER AMENITIES FOR SETTING UP OF AED/ALD DEPARTMENT FOR ICGAE PORBANDAR

Amount

SCHEDULE "A" Part - I (BUILDING WORKS) Details of prepriced schedule is given in tender documents.

SCHEDULE "A" PART-II (SITE CLEARANCE, AREA DEVELOPMENT, EXCAVATION & EARTHWORK) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-III (INTERNAL WATER SUPPLY) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-IV (INTERNAL ELECTRIFICATION) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-V (ROAD PATH AND CULVERT) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-VI (SEWAGE DISPOSAL) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-VII (AREA DRAINAGE) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-VIII (EXTERNAL ELECTRIFICATION) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-IX (EXTERNAL WATER SUPPLY) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-X (REF & AC) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART -XI (MISCELLANIOUS ITEMS) Note:- This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col.' E ' signifies this fact only.

ROAD/ PATH / CULVERT: M&L wet mix macadam (WMM) 100 mm thick (Compacted thickness) with granite stone coarse aggregate of specified grade spread using mechanical paver as required gradient and camber complete all as specified and directed.

M&L for cement concrete 100mm thick dry lean concrete (DLC) using 40mm graded stone aggregate consolidated to required gradient and camber to achive 7 days compressive strength not less than 10 MPA.( For Road work) complete all as specified and directed.

Supply and lay one layer polythene film transparent 400 micron HDPE sheet complete all as specified and directed.

M&L for pavement quality concrete (PQC) of flexural strength 45 Kg/Cm2 in field using minimum 415 Kg of cement per cum as per design mix thickness of concrete 150 mm laying in bays as specified on drgs and adding non circular synthetic fibre as per manufacturers instruction 0.25% by weight of cement complete using computerized concrete batching plant with sensor paver all as specified and as directed. Note :The cost of non circular synthetic fibre shall be measured and paid seperately.(For Road work) complete all as specified and directed.

M&L for painting lines, dashes, arrows, letters, etc. on roads, pavements and the like exc 10cm wide with road marking paint, white or golden yellow complete all as per manufacturer's instruction & traffic diversion arrangement including preparation of surfaces complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 (using 40mm graded) stone aggregate as in bed to drain pipe including packing under and surrounding against the side of pipe after they are laid and tested completed for pipe of 600mm bore complete all as specified and directed.

Internal water supply: S & F Two way bib tap 15 mm make -Drizzel or Prayag or equivalent complete all as specified and directed.

S & F Health faucet with wall hook Make Hindware model No F160027 or equivalent complete all as specified and directed.

S&F, CPVC Gate valves 32 mm dia complete all as specified & directed.

Internal Electrification: S & F modular type bell ding dong of 2 module size, conforming to IS: 8884- 1978 complete all as specified and directed. Make: Legrand Arteor Cat-Part No. 5734 43 or equivalent model of ABB (snieo) / L&T (Entice) / Wipro

S & F modular type 1 module Telephone socket socket complete all as specified and directed.

Supply and Fix LED light fitting 2X 16 watt flame proof, CMRI certified recommended for gas / vapor group of IIA & IIIB Zone 1&2 and IP 65 protection with die cast aluminum housing with heat resistant toughened glass with LED tube light fixture driver holders connector etc complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and directed.

S & F 20 W surface/wall mounted LED batten having high efficiency long life LED chips with luminous efficiency of > 100 lumen/W, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing and white coloured ABS end caps having input voltage 220- 240 V, input frequency 50- 60 Hz, PF > 0.95, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed. Make: Bajaj Cat part No BCLAB20W/ Havells/Phillips/Wipro

S & F 10 W surface/wall mounted LED batten having high efficiency long life LED chips with luminous efficiency of > 100 lumen/W, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing and white coloured ABS end caps having input voltage 220- 240 V, input frequency 50- 60 Hz, PF > 0.95, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed. Make: Bajaj Cat part No BCLSB 10WH /Havells/Phillips/Wipro

S & F 35 W LED building security light having high efficiency long life LED module with SMD LED package mounted on MCPCB with high LED efficiency of ≥ 100 lumen/W, integral SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, IP 66 protection, high effiency polycarbonate cover with integrated lens housed in pressure die-cast aluminium alloy heat sink for effective thermal management, sturdiness, excellent corrosion resistance, separate optical and control gear compartment & top opening for easy maintenance, suitable for side entry, pole mounting with bracket 1.2 m long with including necessary electrical connection to the fixture with 3 core flexible Cu conductor cable of appropriate size and light grade GI pipe (25 mm), including GI clamps, nuts, bolts & washers with two coats of synthetic enemal paint over a coat of red oxide primer complete all as specified and directed. Make: Bajaj Cat part No BCLST 25 W /Havells/Phillips/Wipro

S & F BEE five star rated with BLDC motor energy efficient high-speed ceiling fan having 1200 mm blade sweep, air-flow not less than 210 CMM, operating voltage 220-240 V and frequency 50 Hz, including a down rod of suitable size and electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fan complete all as specified and directed. Make: Crompton Cat-Part No. ENTRUST50 or Havells Cat- Part No. ES-50 or equivalent model of Usha or BAJAJ

S & F engery efficient non-metalic fresh air fan having blade sweep 250 mm, air delivery not less than 860 CMH, operating voltage 220-240 V and frequency 50 Hz, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fresh-air fan complete all as specified and directed. Make: Crompton Cat-Part No. VENTILUS 10" or equivalent model of Usha, Havells or BAJAJ

S & F engery efficient metalic exhaust fan having blade sweep 300 mm, air delivery not less than 900 CMH, operating voltage 220-240 V and frequency 50 Hz, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the exhaust fan complete all as specified and directed. Make: Crompton Cat-Part No. TRANS AIR 12" or equivalent model of Usha, Havells or BAJAJ

S & F MCB for AC applications conforming to IS/IEC 60898-1-2002, having breaking capacity Icn = 10 kA, sliding bottom clamp, colour coded on/off indication on dolly, biconnect IP 20 protected lower terminals and sliding shutters, etc. complete all as specified and directed .Make: Schneider, Legrand, Havells 40A, TPN MCB, C-curve

32A. TPN MCB, C-curv

20 A, SP MCB, C- curve

16A, SP MCB, C-curv

10 A, SP MCB, C- curve

6 A, SP MCB, C- curve

40A, FP MCB, C-curve.

Supply, install, testing and commissioning of factory made and tested indoor type pedestal mounted on PCC Floor. LT panel board cubicle type panel board suitable for 415 volts, 3 phase, 4 wire, 50 Hz AC supply system having bus bar chamber with air insulated PVC sleeved with heat shrink of colour code on copper bus bar of rating 400 Amps for phases and neutral fixed on porcelain insulators. The panel shall be weather proof, dust and vermin proof IP-54 class protection and fabricated out of 2 mm CRCA sheet duly powder coated after seven tank process and pedestal of size 50 x 50 x 6 mm thick MS angle iron frame work. The panel shall be both front and back openable type adequate space all around acessories such as LT MCCB and measuring instruments on both sides including internal wiring in the panel with PVC insulated multi stranded copper conductor cable 1100 Volt grade IS 694 marked or PVC sleeved copper strips of appropriate size as per standard is practices and comprising of followings acessorties (Building main panel) INCOMINGS (a) MCCB 415 Volts,315 Amp , rating 4 Pole microprocessor based (triple pole and neutral), Thermal Magnetic release (Service Breaking Capacity 35 KA)- 1 Nos. (b) Digital multi function Panel Mounted Meter with all necessary CTs, PTs and instrument fuses and wiring OUTGOING (a) MCCB 415 Volts,160 Amp , rating 4 Pole microprocessor based (triple pole and neutral), Thermal Magnetic release (Service Breaking Capacity 25 KA)- 1 Nos. (b) MCCB 415 Volts, 40 Amp rating 4 Pole (triple pole and neutral), (Service Breaking Capacity 16 KA)- 08 Nos. (c) MCCB 415 Volts, 63 Amp rating 4 Pole (triple pole and neutral), (Service Breaking Capacity 16 KA)- 02 Nos. (d) MCB TP 415 Volts, 40 Amp rating - 01 Nos. (e) MCB TP 415 Volts, 20 Amp rating - 01 Nos. (f)Contactor suitable for 32 A TP for flood lights Timer (g) Internal wiring of panel with stranded copper cable of suitable size (h) LED phase indicating lamp(Set of three)-01 Nos (j) Stenceling of pannel board including marking of distribuitions

Supply, install, testing and commissioning of factory made and tested indoor type pedestal mounted on PCC Floor. LT panel board cubicle type panel board suitable for 415 volts, 3 phase, 4 wire, 50 Hz AC supply system having bus bar chamber with air insulated PVC sleeved with heat shrink of colour code on copper bus bar of rating 400 Amps for phases and neutral fixed on porcelain insulators. The panel shall be weather proof, dust and vermin proof IP-54 class protection and fabricated out of 2 mm CRCA sheet duly powder coated after seven tank process and pedestal of size 50 x 50 x 6 mm thick MS angle iron frame work. The panel shall be both front and back openable type adequate space all around acessories such as LT MCCB and measuring instruments on both sides including internal wiring in the panel with PVC insulated multi stranded copper conductor cable 1100 Volt grade IS 694 marked or PVC sleeved copper strips of appropriate size as per standard is practices and comprising of followings acessorties (Building main panel) INCOMINGS (a) MCCB 415 Volts,160 Amp , rating 4 Pole microprocessor based (triple pole and neutral), Thermal Magnetic release (Service Breaking Capacity 35 KA)- 1 Nos. (b) Digital multi function Panel Mounted Meter with all necessary CTs, PTs and instrument fuses and wiring OUTGOING (a) MCCB 415 Volts,40 Amp , rating 4 Pole (triple pole and neutral), (Service Breaking Capacity 16 KA)- 5 Nos. (b) MCCB 415 Volts, 63 Amp rating 4 Pole (triple pole and neutral), (Service Breaking Capacity 16 KA)- 05 Nos. (d) MCB TP 415 Volts, 32/40 Amp rating - 01 Nos. (e) MCB TP 415 Volts, 20 Amp rating - 01 Nos. (f) Internal wiring of panel with stranded copper cable of suitable size (g) LED phase indicating lamp(Set of three)-01 Nos (h) Stenceling of pannel board including marking of distribuitions

EXTERNAL WATER SUPPLY Supplying and laying in trenches centrifugally cast (spun) ductile iron pipes of 100 mm dia suitable for pressurized water delivery with spigot & socket end, class 'K-7' conforming to IS:8329/2000 (latest version) - blast furnace slag cement with portland cement properties sitable for (push on) rubber gasket jointing with inside cement mortar lining and black bitumen external coating, duly ISI marked in any length including testing and commissioning complete all as specified and directed.

REFRIGERATION & AC Supply and fix voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 140 V to 280 V, with output voltage stabalized at 230 volt with accuracy of +/- 2.5% and of capacity 1 KVA complete all as specified and directed. Make: V-Guard / PIXEL / Aplab / Volina

Supply and fix voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 140 V to 280 V, with output voltage stabalized at 230 volt with accuracy of +/- 2.5% and of capacity 3 KVA Make: V-Guard / PIXEL / Aplab / Volina complete all as specified and directed.

Supply, install and test Split air conditioner, inverter type electric driven, single phase, of capaciy 1.5 Ton, 3 star rated with copper condenser, indoor noise level < 50 db with standard fitment and outdoor unit fixed on wall mounted type bracket and connected to power supply complete all as specified and directed. Make : Voltas/ LG/Carrier

Supply, install and test Split air conditioner, inverter type electric driven, single phase, of capaciy 1 Ton, 3 star rated with copper condenser, indoor noise level < 50 db with standard fitment and outdoor unit fixed on wall mounted type bracket and connected to power supply complete all as specified and directed. Make : Voltas/ LG/Carrier

Supply and fix on line UPS 7.5KVA, 3phase AC with 30min backup working input voltage 415 volt with variation +- 1% including battery bank of sufficient battery backup as per manufacturer instructions complete all as specified and directed.

Supply & fix integral LED obstruction light yellow painted die cast aluminium alloy housing. Red coloured polycarobnate dome complete with accessories complete all as specified and directed. Model No : BGAV 302 LED. Make : Bajaj

EXTERNAL ELECTRIFICATION Supply and fix Voltage stabilizer for automatic operation, three phase, naturally oll cooled, indoor type & designed for input variation between 300 V to 480 V with output voltage stabilized at 415 with accuracy 2.5% and speed of correction 8 Volts per second and of capacity 100 KVA complete all as specified and directed. Make: V-Guard/Servo controlled/PIXEL (FUY+Hongen)

Supply. Installation & commissioning of factory made. manufactured by CPRI approved manufacturer, self supporting totally enclosed LT Panel Board (out door type) compartmentalized design, dust & vermin proof bf size not less than of size 1 9x1.8x0.45mtr suitable for 440 Volt 3 phase 4 wire system confirming to(IP-54) complete including Copper bus bar 400 Amp and madeup of CRCA sheet of(3.15] mm thick built upin rigid frame work having front and rear hinged door with neoprene rubber gasket, epoxy powder coated including danger plate, earth strip point and ventilation louvers at the rear side, bottom detachable gland plate complete with suitable size zinc chromium plated nuts,bolts and washers, etc. having control circuit diagram with colour code solid conductor copper 1.5 sqmm cable for easy identification including Incoming/ Outgoing cable holes at bottom, ermbeded with 50x6mm mild steel angle Iroh frame and 200 mm above the normal ground level complete with PCC foundation in cement concrete 1.2:4 (20mm graded stone aggregate) and testing after installation including taking down unserviceable LT panel board complete all as specified and comprising with the following: Make Universal/Advance/ SIGMA (a) Incoming MCCB 250 Amps four pole with microprocessor based release , having breaking capacity 36 KA -01 No (b) Outgoing MCCB 63 Amps four pole with microprocessor based release having breaking capacity 10 KA -5 No (c) Outgoing MCB TP 63 Amps with microprocessor based release having breaking capacity 10 KA 4No (d) Outgoing MCB DP 40 AMPS with microprocessor based release having breaking capacity 10KA-4No (e) Digital MFM for Amp , Volt,KWH,power factor and other parameter flush mounting of size 96x96 mm complete all as specified and directed.

Vastushilp Building Designer

Gatral Construction Co.

JAMNAGAR ELECTRIC AND MACHINERY CO

RAJ ENTERPRISE

m/s.a.t.odedra

M/s SK Traders

Nitesh Enterprise