RENOVATION OF LHAMO KHANG (GODDESS HOUSE) AT CENTRAL CONPA, EST NO 22 THROUGH GE (P), DEHRADUN

Amount

Dismantling wall and ceiling board fibre, pulp insulation etc or insulation boards any thickness including cover fillets complete all as specified and directed.

S & F 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-primetered self embossed, textured designer board E-Board Classic to be fixed GI powder coated grid/section size 600mmx600mm with main runner 38x24x0.9mm thick, cross tee 28.6x24x0.9 mm and wall angle 19x19xo.9 mm duly suspended with 2mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing) removing serviceable tiles to store and rubbish off the premises and removing the debris outside from defence land complete all as specified and directed .

S&F Non skid ceramic coloured tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but n.exc 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles laid over and including 15mm thick screed bed or bedding layer of mortar for laying floor finishes in CM (1:6) complete all as specified and directed.

All as per item No.04 above but on vertical surfaces such as skirting , dado risers to steps fixed over and including 10 mm thick bedding layer in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed .

S&F vitrified ceramic tiles light shade 10mm thick (Square/rectangular)area of each tiles n.exc 0.36 Sqm each in floors set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles laid over and including 15mm thick screed bed or bedding layer of mortar for laying floor finishes in CM (1:6) complete all as specified and directed.

All as per item No.06 above but on vertical surfaces such as skirting , dado risers to steps fixed over and including 10 mm thick bedding layer in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed .

S&F 4.5mm thick Linoleum, plain coloured, laid dry in floors including stretching, cutting and fitting and sealed down with an approved adhesive all as specified and as directed.

S&F in repair 4 mm thick figured glass, pin head type and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and directed.

S & F 500 ltr Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layered with ball brass valves, high pressure, with 20 mm polythene float and flynut complete, screwed for iron pipe or brass ferrule hoisted and fixed in position incl fixing of inlet, outlet & over flow pipe all as specified in SSR Part I including dismantling of existing unserviceable tank complete all as specified and directed.

Taking down cement plaster any thickness any description on brick or stone walls, partitions, ceilings etc incl raking out joints hacking for key scrubbing down with water etc including cleaning of bush, shrubs, vegetation, grass,weed,saplings etc complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of stone masonry work in CM (1:6) and finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for 20 mm thick rendering on fair faces of stone masonry work in CM (1:4) and finished even and smooth without using extra cement all as specified & directed

M&L for applying two or more coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre of approved manufacturer, of required shade and colour complete, as per manufacturer's specification on new work complete all as specified and as directed.

M&L for finishing walls with Acrylic smooth exterior paint of required shade on new plastered (Two or more coat applied @ 3.28 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) bends any radius 75mm dia complete all as specified and directed.

Demolition of cement concretee (unreinforced) in ground floors and Pavings not exc 15 cm thick (below or above ground level ) and removing the debris outside from defence land complete all as specified and directed .

M & L for 75mm thick PCC 1:3:6, type C-2 (using 20mm graded crushed stone aggregate) as in plinth protection and paving laid in slope finished even and fair including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight complete all as specified and directed.

Demolition of brick /stone work , built in cement mortar or cement lime mortar including all quions, arches, pillars, etc disposal of debris out of MoD land complete all as specified and directed.

M & L for brick work with old size sub class 'B' bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick/concrete surfaces in CM (1:4) and finished even and smooth without using extra cement all as specified & directed

M&L for preparation of new plastered surface of walls including cornices, pilasters etc and applying two coats of Weather proof exterior emulsion paint over a coat of primer complete all as specified and directed.

M & L for 75 mm thick PCC 1:4:8, type D-2 (using 40mm graded crushed stone aggregate ) as in sub-base etc complete all as specified and directed.

S&F 300x300mm and 12mm thick exterior parking tiles laid and jointed with grey cement slurry mixed with pigment in floor to match the shade of the tiles complete all as specified and directed by Engineer in Charge.

Taking down carefully existing aluminum/copper surface / concealed point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, lamp holder, regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and making good the disturbed surfaces in CM 1:3 of walls, floors, ceiling etc including distempering to match with existing surfaces complete all as specified and directed.

Taking down unserviceable main switch, DBs, Teak wood boards etccomplete all as specified and directed.

M&L point wiring with 1.5 Sqmm (nominal area) two single core PVC insulated unsheathed multi stranded copper conductor cable 1100 volts grade, FRLS-H grade in and including medium duty concealed/ surface PVC conduit 20 mm dia or higher and conduit fittings and all accessories with suitable size of Metal flush box zinc oxide plated or PVC non metallic surface mounting type box,as per site requirement, with modular plate and frame of 01 module to 18 module as required at site, for mounting of modular switches, sockets etc including conteneous earth wire PVC insulated, unsheathed, multi stranded copper conductor cable 1.5 sqmm (nominal area) FRLS-H grade, green colour, up to common earth and connected to earth dolly compete all as specified and directed of the following. Note :-(a) Point wiring should be carried out on surface mounted rigid PVC conduit at the places, where RCC beam, column, truss, roof or false ceiling exists and as per direction. (b) Colour code will be maintained as per IE rule i.e. Red/Yellow/Blue for phases, Black for Neutral and Green for earth wire. (c) Cost of Modular Metal flush box, modular plate and frame deemed to be included in quoted rate for point wiring and the of flush metal box will be decided by the Engr-In-Charge. (d) Make of Modular metal flush box or PVC non metallic surface mounting type box modular plate and frame, switch, socket, regulator, bell push should be same & colour of frame switches match up with the surrounding. (e) Switch, socket, regulator, bell push will be measured and paid separately under respective item.

One light/fan / bell point controlled by one 1-way switch.

One three pin 5 Amp socket on same board.

One three pin 5 Amp socket on independent board

One light point controlled by two 2-way modular switches.

All as per item No.28.0 above but one 3 pin socket outlet 15 Amp independent, with cable 2.5 Sq mm size, with earth continuity coductor of size 2.5 Sq mm.

All as per item No 28.0 above but with 4sqmm copper conductor cable with 4 sqmm PVC copper conductor cable as earth continuity conductor for one socket outlet 15/16 amps (AC/geyser) on independent board all as directed.

S & F Lamp holder B-12 type, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings complete all as specified and directed.

S & F modular switch 1 way 6A, 1 Module complete all as specified and directed.

S & F modular socket 6A, 2 / 3 pin combined 2 Module complete all as specified and directed.

S & F modular switch 1 way 16A, 1 Module with indicator lamp complete all as specified and directed.

S & F modular socket 6A / 16A, 2/3 pin combined 2 Module complete all as specified and directed.

S & F modular switch 2 way 6A, 1 Module complete all as specified and directed.

S & F modular bell push 6A, 1 Module complete all as specified and directed.

S & F ding dong bell AC 230 V single pole complete all as specified and directed.

S & F ceiling rose, 3 terminal/PVC/polycarbonate, isolated body 230 V AC complete all as specified and directed.

Supply & fix Wall mounted LED batten fitting, 22 W,230 volts AC,T-8, cool white not less than 1200mm extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver with and including 22 W LED tube rod complete and connected the same with using PVC sheathed and insulated 3 core flexible 23/0.0076 copper conductor cable including all accessories and fixing arrangement for fixing the light fitting to walls including taking down existing fitting complete all as specified and directed.

S & F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S & F Material of LED inverter bulb 9 watt retrofit type works on AC Normal mode and DC supply in inverter mode with inbuilt battery back up of up to 4 hours, high efficiency high lumens output complete all as specified and directed.

S & F LED wall mounted study lamp 3.0W, 4V, 2000mAh. including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 40/42 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades and deposited to E/M store yard at own cost complete all as specified and directed.

S&F Metallic Heavy duty steel body Exhaust fan ith louvers, blades, with fixing arrangements & making hole of suitable size if necessory for 300 mm sweep, 230V, AC single phase including nuts, bolts and washers complete all as specified and directed.

S & F Sheet metal enclosure, single pole and neutral with two pin and earth plug and socket with MCB SP 20A, suitable for protection of appliances like AC/Geyser suitable for flush mounting and surface mounting complete all as specified and directed.

Supply and fix electric water heater stoarage type steel body with copper inner tank & heating element upto 2KW capacity 25Ltr, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, Connection piece complete all as specified and directed.

M & L for sub main wiring with 2 Single core PVC insulated unsheathed FRLS-H cable 1100 Volts grade heavy duty copper conductor multistranded of size 4.0Sqmm (nominal area) drawing in and including 20/25mm dia PVC conduit medium duty concealed/surface (column/beam/ roof) conduit heavy duty accessories and fittings with chasing/cutting complete with 1 run of copper conductor multistranded of size 4.0 Sq mm as earth wire upto common earth and connected to earth dolly complete all as specified & directed. Note :-3 runs of 4 sqmm copper cable & one run of PVC conduit shall be measured as one running metre.

All as per item No.49 above but size of cable 2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire.

All as per item No.49 above but size of cable 2 x 6.0 sq. mm + 1 x 6.0 sq. mm earth wire.

S & F LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection with GI bracket of dia 40mm light grade of suitable size with complete all as specified and directed.

S & F VTPN 4 ways (VTPN DB) with metal door (IP 43 IK 09 protection) suitable for one FP MCCB 100 Amps as incomer and 12 SP MCBs or any combination of SP / TP MCBS outgoings complete all as specified and directed..

S & F MCCB 415 Volt 16 KA 3/4 pole 100 Amp magnetic release adjustable range as incoming with fixing arrangement complete all as specified and directed.

S & F MCB single pole and 240 volt 10 KA 6-32 Amp 'B' series complete all as specified and directed.

Supply and fix in replacement on-load changeover switch 415 V, 4 pole, 125 A. open execution complete all as specified and directed.

M & L for earthing complete with using galvanized mild steel earth plate (electrode) 600 mm x 600 mm x 6 mm thick buried directly in ground, earth pit not less than 2.25 mtr deep below ground level with top edge of the earth plate not less than 1.50 m below ground level and earth plate surrounded with adequate quantity of charcoal dust mixed with salt to be packed thickness of 15 cm all round the plate using 4 mm dia GI earth lead wire as earth lead moulded and rivetted to earth plate at one end and connected to main equipment at switch/control board at another end, GI earth lead protected in and including 15 mm dia GI ‘medium grade’ pipe from upper end of earth plate upto equipment with & including 20 mm dia bore GI pipe ‘medium grade’ as water pipe from earth chamber to upper edge of the earth plate, GI funnel with wire mesh fixed on water pipe and provision of PCC 1:2:4 type B1(using 20 mm graded stone agg) as in pits chamber and RCC pit cover 50 mm thick of precast RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as per electrical plate No.3 of SSR Part-II 2010 and testing on completion all as specified and directed.

Supply and fixing bollard light LED mushroom type 20 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete.

HARJINDER PAL SINGH (BID ID -3422510)

MOHAN SINGH AND SONS (BID ID -3422162)