Augmentation of LIS Jukhala, Ashamajari, Panjaitan, Bhatoli, Rihri and Rihan in Tehsil Sadar District Bilaspur (H.P.).

Amount

Cutting in earth work and disposal of excavated earth in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Excavation in foundation and trenches etc. in earth work in all lifts in all kinds of soil such as pick work, jumper work, blasting work in soft/hard rock chiseling/wedging out of rock) where blasting is prohibited saturated soil including bailing/pumping out of water stacking the excavated soil in 15cm layers, when required into plinths, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed with in all leads and lifts and to the entire satisfaction of the Engineer-in-charge. (Pick jumper work).

Providing and laying cement concrete 1:6:12 (1cement: 6sand: 12 graded stone aggregate 40mm nominal size) and curing complete in foundation and plinth and to the entire satisfaction of the Engineer-in-charge.

Providing and laying cement concrete 1:4:8(1cement:4sand:8 graded crushed stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of materials in all leads and lifts.

Providing and laying cement concrete 1:3:6 (1cement: 3sand: 6 graded stone agg. 40mm nominal size) excluding the cost ofcentering & shuttering in foundation and plinth in all leads and lifts.

Square rubble masonry coursed with hard stone of approved quality in foundatoin and plinth including racking out joints in cement mortar 1:6 (1cement: 6sand) with in all leads and lifts and to the enitre satisfaction of the Engineer-in-charge.

Square rubble masonry coursed with hard stone of approved quality in superstructure above plinth level and upto floor two level including racking out joints in cement mortar 1:6 (1cement: 6sand) with in all leads and lifts and to the enitre satisfaction of the Engineer-in-charge.

Providing and laying cement concrete 1:2:4 (1cement:2sand:4 graded stone aggregate 20mm nominal size) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in :-

Foundation footings bases of columns and the like and mass concrete and to the entire satisfaction of the Engineer-in-charge.

Suspended floor roofs landing shelves and their supports balconies, beams girders bressumers and cantilevers up to floor two level.

Column, pillar, posts, struts, square, rectangular on polygonal as per direction of Engineer-in-Charge upto all lead and lifts.

Providing wood work in doors windows, clerstory windows and other frame and fixed in position 2nd class deodar wood in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Providing and fixing panelled glazed or panelled and glazed shutter 40mm thick 2nd class deodar wood and to the entire satisfaction of the Engineer-in-charge.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws 2nd class deodar wood 40mm thick including carriage of material in all leads & lifts.ist class deodar wood and to the entire satisfaction of the Engineer-in-charge.

Providing and fixing pressed steel doors frames manufactured from commercial mild steel sheet of 1.25mm thickness including hinges jamp lock jamb bead and if required angle threshold of mild steel angle of section 50x25mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with splita and tails to each jamp including steel butt hinges 2.5mm thick with guards, lock strike plate and shock as specified and applying a coat of approved steel primer after pretreatment of the surface as directed by the Engineer-in-charge. Profile-A

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens ballies, height of propping and cent ring below supporting floor to ceiling not exceeding 4 mtr and removal of the same for in-situ reinforced concrete and plain concrete work in:-

Foundation footings base of columns and the like and mass concrete and to the entire satisfaction of the Engineer-in-charge.

Flat surfaces such as soffits of suspended floor landings and the like up to 200mm thickness and to the entire satisfaction of the Engineer-in-charge.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pilasters buttresses, plinth and string courses and the like and to the entire satisfaction of the Engineer-in-charge.

Sides and soffits of beam, beam hounching,cantileverand bressumers and lintels not exceeding 1.00mtr in depth in all heights from floor complete in all respect in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Edges of slab and breaks in floors and walls (under 20cm wide) in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Columns, pillars, posts and struts Square, rectangular or polygonal in plan as per direction of Engineer-in-Charge upto all lead and lifts.

Providing and laying cement concrete 1:1:5:3 (1cement:1.5sand:3 graded stone aggregate 20mm nominal size) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in :-

Foundation footings base of columns and the like and mass concrete and to the entire satisfaction of the Engineer-in-charge.

Wall any thickness but not less than 0.1mtr thickness attached pilasters, buttresses, plinth and string courses etc. from top of foundation level up to floor two level and to the entire satisfaction of the Engineer-in-charge.

P/L precast slab in nominal cement concrete Mix M20 and curing complete exculding cost of form work in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

15mm cement plaster in single coat of rough side of brick/ concrete/ stone walls for interiorplastering in all depths and the height including arises internal rounded angles exceeding 80mm in girth and finished even and smooth in cement mortar 1:6 (1cement: 6sand) in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

20mm cement plaster in double coat of rugh side of bricks/ concrete stone walls for interior plastering upto floor two level including arrises internal rounded angles chamfers and rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:6 (1cement:6sand) in all leads and lifts.

6mm thick cement plaster to ceiling in CM 1:3 (1cement:3sand) in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Providing tor steel reinforcement for RCC work including bending binding and placing in position complete in all depths and heights and to the entire satisfaction of the Engineer-in-charge.

Applying priming coat over new wood and wood based surface after and including preparing the surface by thoroughlycleaning oil dirt grease and other foreign matter sand papering and knotting ready mixed paint brushing wood primer pink in all leads and lifts.

Painting two coats (excluding priming coat) on new wood and wood based surface with ready mixed paint brushing the give and even shade including cleaning of all dirt dust and other foreign matter and sand papering and stopping with ready mixed paint other than white in all leads and lifts.

Distempering with dry distemper or approved brand and manufacture (two coats) and or required shade on undecorated wall surface to give an even shade over and including primer coat of whiting after, thoroughly brushing and surface free from mortar dropping and other foreign matter including preparing the surface even and sand papered smooth.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces (two coats) to give an even shade after throughly brushing the surface to remove all dirt and remains of loose powdered material in all leads and lifts.

Providing and fixing MS grills of required pattern in wooden frame of window etc. with MS flat, square or round bars with round headed bolts and nuts or by screws complete in all respect within all leads and lifts.

Providing and fixing bright finished MS sliding door-bolts with nuts and screws etc. complete in all respect including carriage of material in all leads & lifts and to the entire satisfaction of the Engineer-in-charge (250x16mm)

Providing fixing bright finished MS tower bolts (barrel type) with screws etc. complete. in all respect including carriage of material in all leads & lifts.

Providing and fixing bright finished MS handles for doors with screws etc. complete. in all respect including carriage of material in all leads & lifts and to the entire satisfaction of the Engineer-in-charge.

Providing in RCC work smooth finishing of the exposed surface with cement mortor 1:3(1cement: 3sand) and to the entire satisfaction of the Engineer-in-charge.

Providing and fixing MS rungs in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Providing and laying cement concrete 1:5:10 (1cement:5sand:10 graded stone aggregate 40mm nominal size) with 15% plum and curing complete excluding the cost of form work in retaining walls, breast walls , the size of plum shall usually be 150 to 300mm as per HPPWD specification and to the entire satisfaction of the Engineer-in-charge.

Brick work using common burnt clay building bricks Ist class in super structure above plinth level upto floor two level in cement mortar 1:4 (1cement: 4sand) in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Brick work using common burnt clay building bricks 2nd class in super structure above plinth level upto floor two level in cement mortar 1:6 (1cement: 6sand) in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Half brick masonry in common burnt clay building bricks in cement mortar 1:4 (1cement: 4sand) extra half brick masonry in super structure for above plinth level uptofloor two level and to the entire satisfaction of the Engineer-in-charge.

Pointing on brick work with cement mortar in 1:3 (1cement: 3sand) in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

White washing with lime on undeocrated walls surface ( two coats) to give an even shade including thoroughly brooming the surface dirt dust mortar dirt and other foreign matter in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Providing and fixing sand cast/cast iron spun spigot and socket soil, waste and ventilating pipes (Lead caulked joints 100mm dia to be measured and paid for separately).

Stone/ boulder filing behind the retaining wall also under floor and upstream of I/gallery under floor etc. in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Providing 40x3mm flat iron hold fast 40cm long including fixing to frames with ten millimeters dia of bolts nuts and wooden plug and embedding in cement concrete block 30x30x15, 1:3:6 (1cement:3sand: 6 graded stone) agg. 20mm.

Wire crates made of GI wire filled with boulders with square cut faces against the wire (wire crates to be measured and paid for separately) GI wire 5.00 mm thick corresponding to SWG-6 (15x15cms mesh) in all leads and lifts and to the entire satisfaction of the Engineer-in-Charge.

Wire crates of GI wire filled with boulder with square cut faces against the wire (boulder filling to be measured and paid for separately) GI wire 5.00mm thick corresponding to SWG-6 (15x15cms mesh)with in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Dressing of bed and side slopes preparation of sub grade for lining in pick work in all leads and lifts and to the entire satisfaction of the Engineer-in-charge. (In bed)

In side slopes

Cement concrete lining 15mm thick or less for irrigation channel in cement concrete 1:3:6 (1cement: 3sand: 6 graded aggregate and to the entire satisfaction of the Engineer-in-charge.

Hand mixed concrete lining in bed and to the entire satisfaction of the Engineer-in-charge.

Hand mixed concrete in lining in side slopes and to the entire satisfaction of the Engineer-in-charge.

Extra allowance for form work in concrete lining in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Providing and fixing cast iron man hole cover with frame (Medium duty) 500mm dia cver nt less than 100kg including carriage of material in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Providing cement concrete flooring 1:2:4 (1cement: 2sand: 4 graded stone aggregate nominal size laid in one layer finished with floating coat of neat cement and to the entire satisfaction of the Engineer-in-charge.40mm thick

Providing and fixing toilet sheet (Orrisa Pan) Cera make and to the entire satisfaction of the Engineer-in-charge.

Providing and fixing 500 ltrs. Double layer sintex make water storage reservoir with top lid and making connection complete in all respect including all leads and lefts.

Providing and fixing flushing cistern 5 ltrs capacity including entire carriage of material within all leads and lifts.

Providing and fixing electrical & sanitary fitting in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

FITTINGS AND ACCESSORIES

110mm dia PN-4/5/6/8 HDPE Pipes in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

110mm dia PN-6 HDPE Pipe end in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

110mm dia PN-6 HDPE Pipe 900 bends in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

110mm dia PN-6 HDPE Pipe QC Pump Connector in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Providing laying (to level or slopes) and jointing RCC pipes of class P2 with collars and butt ends prepared for collars joints including testing of joints complete as per IS code 458-2003 with latest amendements including all leads and lifts and to the entire satisfaction of Engineer-in-charge.

RCC Pipe of 900mm dia NP2

RCC Pipe of 350mm dia NP2

Providing and fixing CI Control/sluice valve 80mm dia Kirloskar/Leader make including all leads and lifts and to the entire satisfaction of Engineer-in-charge.

Steel work welded in built up section including cutting, hoisting fixing in position and applying a priming coat of red lead paint in gratings framed guard, bars, ladders railing brackets and similar works in all lead and lifts and to the entire satisfaction of the Engineer-in-charge.

Miscellanious for locking arrangement & other accessories as per direction and t the entire satisfactin f the Engineer-in-charge.

Providing and fixing of fencing panel of size 1.20m x2.40m devided in two panels f 1.20mX 1.20m by fixing T iron at centre fitted with wire mesh 25mmx25mm welded to MS angle frame all arund with MS flat cover and seven Nos hold fasts including cutting welding painting with red oxide paint complete in all resepct and to the entire satisfaction of the Engineer-in-charge.

ELECTRIAL ITEMS Providing and laying PVC insulated PVC sheathed armoured /XLPE power cable of 1.1 KV grade direct in ground including excavation sand cushioning protective covering and refilling the trenches of the required size.

Aluminium conductor PVC insulated armoured cable working voltage 1.1 KV grade twin core 6mm2.

Aluminium conductor PVC insulated armoured cable working voltage 1.1 KV grade twin core 10mm2.

Supply and erection of GI pipe pole 4 mtr long having 65mm dia nominal bore planking depth 80cm with pit depth 95cm confirming to IS: 1239 Part-1 1968 including fixing upto given depth below ground level, the hole of ecavation about 30cm dia and given depth to be fitted a 15cm below ground level with Cc 1:3:6 (1cement: 3sand: 6 graded stone agg. 20mm nominal size upto height of 45 cm below ground level. The radial thickness of the plinth above ground level should not be less than 6.35 cm and sufficient to completely two way single pole neutral sheet steel MCBCB 240 voltage on recess complete with tinned copper busbar chamber neutral link detachable gland plates interconnection including painting earthing etc. having 15/16 amp rating "L" series MCB of single pole in the existing MCBCB complete with testing and commission etc. as required complete in all respect.

Supply and erection of GI pipe pole 1 mtr long having 65mm dia (for gate) including fixing MVL fitting and duly embedded in the existing gate piller for having gate light and also fixing 2 way MCBDB with 15/16 amp MCB in the existing gate piller recessed including connections testing and commissioning etc. as required complete in all respect

Supply and installation of sodium vapour light 250 watt including 900 bend 40mm dia GI pipe (L) class complete at site of work and to the entire satisfaction of the Engineer-in-charge.

Supply and installation of Mercurry vapour light 125 watt complete in all respect

Supply and erection of following size of PVC insulated copper conductor single core cable in existing surface/recessed PVC/ steel conduit PVC casing capping as required 1011 CUEC 2x2.5mm2.

Providing and fixing of 8 way single pole and neutral sheet steel MCB distrtribution board 240 volts on surface/recess complete with tinned copper busbar neutral link, earth bar, dinbar detachable gland plate, inter connections including painting earthing as required.

Supply and fixing wall mounted wooden board 102mmx102mmx60mm including painting etc as required

Providing laying and fixing PVC insulated PVC sheathed armoured/ XLPE aluminium conductor power cable of 1.1 KV grade on surface etc.of required aluminium conductor PVC insulated armoured cable working voltage of 1.1 KV grade (Twin core)10mm2

Providing and laying GI pipe 50mm dia medium grade including inspection box as required complete in all respect

Supply and fixing following the rating,double pole 240 volts insolator in the existing MCBDB / RCCB complete with connection, testing and commission etc. as required

Supplying and fixing 5 Amp to 32 Amp rating 240 volt 'L' series miniature circuit breaker of single pole in the existing MCBDB complete with connection with testing and commissioning etc. as required

SHIV KANT PRASHAR

Sh.Rattan Lal