BID DOCUMENT FOR CONSTRUCTION OF BOOK SCLUPTURE, BEAUTIFICATION AND ELECRTRICAL WORK AT DABHAN FOR NADIAD MUNICIPAL CORPORATION.

Total Amount Rs:-

Sr. No. Description Qty Unit Rate Amount

Dismentaling tiled of stone floors laid in mortar including stacking of

1.00 serviceable materilas and disposal of unserviceable materials with all lead and 1332.66 Smt 46.77

Demolition including stacking of serviceable materilas and disposal of

unserviceable materials with all lead and lift. (i) R.C.C. Work

Clearing and grubbing road land including uprooting rank vegetation grass

bushes,shrubs,sapling and trees girth up to 300 mm removal of stumps of trees

cut earlier and disposal of unserviceable materials (C) By mechanical means in

area of light jungle

Pre-cast Concrete Kerb providing and fixing M20 Grade of Concrete Precast

4.00 exposed pimple texture finish kerb stones and size approved as per design by 1337.80 Rmt 1457.43

architrect and engineer-in-charge.

Supplying and stacking of good earth at site including royalty and carriage upto

5.00 5 km lead complete (earth measured in stacks will be reduced by 20% for 199.90 Cmt 681.14

Supplying and stacking of well decayed cattle manure at site including royalty

6.00 and carriage upto 5 k.m.lead complete (Cattle manure measured in stacks will 199.90 Cmt 565.34

reduced by 8% for Payment).

Mixing earth and sludge or manure in the required proportion specified or

directed by the Officer-in-charge

Spreading of sludge, dump manure and/or good earth in required thickness as

8.00 per direction of officer-in-charge (cost of sludge, dump manure and/ or good 199.90 Cmt 67.54

earth to be paid separately).

Providing & laying of Selection no. 1 Doob grass turf with earth 50mm to

60mm thickness of existing ground prepared with proper level and ramming

with required tools wooden and than rolling the surface with light roller make

the surface smoothen and light watering the same and maintenance for

days or more till the grass establish properly, as per direction of the officer-in-

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting

10.00 out and stacking of useful materials and disposing off the excavated 108.65 Cmt 117.08

stuff upto 50 Meter lead.(C) Hard Murrum

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting

11.00 out and stacking of useful materials and disposing off the excavated 108.65 Cmt 174.23

stuff upto 50 Meter lead D. Soft Rock

Filling available excavated earth (excluding rock) in trenches. plinth, sides of

12.00 foundations etc. in layers not exceeding 20 cm. in depth consolidating each 145.61 Cmt 130.39

disposited layer by ramming and watering.

Providing and laying cement concrete 1:3:6 (1-Cement : 3- coarse sand : 6-

hand broken stone aggregates 40 mmnominal size) and curing complete

excluding cost of formwork in (A) Foundation and Plinth (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete

excluding the cost of formwork and reinforcement for reinforced concrete

work in (A) Foundations, footings, Base of columns and Mass concrete.

RCC Wall : Providing and laying controlled cement concrete M.250 and curing

complete excluding the cost of formwork and reinforcement for reinforced

concrete work in (B) Walls, from top of foundation level upto floor two level

Providing and laying controlled cement concrete M.250 exposed work with

16.00 curing etc. complete including the cost of formwork but excluding the cost of 3.24 Cmt 10824.26

reinforcement for R.C.C. work in (A) BEAMS

NADIAD MUNICIPAL CORPORATION - NADIAD

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF BOOK SCLUPTURE, BEAUTIFICATION AND ELECRTRICAL WORK AT DABHAN FOR NADIAD MUNICIPAL

Sr. No. Description Qty Unit Rate Amount

Providing formwork of ordinary timber planking so as to give a rough finish

including centering shuttering trutting and propping etc. Height of propping

and centering below supporting floor to ceiling not exceeding 4 M. and

removal of the same for in situ reinforced concrete and plain concrete work in.

(A) Foundations Footings Bases of Columns etc. and Mass concrete.-

Providing formwork of ordinary timber planking so as to give a rough finish

including centering shuttering strutting and propping etc. height of propping

and centering below supporting floor to ceiling not exceeding 4 M. and

18.00 removal of the same for in situ reinforced concrete and plain concrete work in. 560.52 Smt 232.25

(C) Vertical surface such as walls (any thickness) partitions and the like

including attached buttresses & string course & the like.

Providing formwork of ordinary timber planking so as to give a rough finish

including centering shuttering strutting and propping etc. height of propping

and centering below supporting floor to ceiling not exceeding 4 M. and

19.00 removal of the same for in situ 12.96 Smt 195.67

reinforced concrete and plain concrete work in. (H) (1) Sides and soffits of

Beams Beam Haunchings cantilevers Girders Bressumers and Lintels not

exceeding 1 M. in Depth.

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work including

20.00 bending, binding and placing in position complete (upto 10 ton) 21582.15 Kg 76.21

Exterior plaster upto Three floor GL: 20mm thick sand faced cement plaster on

walls upto height 10 metres above ground level consisting of 12mm thick

backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of

C.M. 1:1 (1-cement : 1-sand) etc. complete.

Providing and applying exterior acrylic texture paint of approved brand and

22.00 shade on prepared surface including surface cleaning, primer coat, and 630.64 Smt 1168.12

necessary scaffolding, complete as per manufacturer specifications.

Supply, fabricate, and install decorative stainless steel leaf element fabricated

from Grade 304 stainless steel sheet of (minimum thickness 8mm) as per

architecture drawing and Engineer-in-charge, laser cut to approved design

23.00 pattern, including forming, bending, edge finishing, surface polishing (hairline / 6.00 Each 151500.00

mirror finish), welding, grinding, and fixing to supporting frame with stainless

steel fasteners, complete in all respects as per approved shop drawings and

site instructions.

Supply and installation of customized logo signage fabricated using high-quality

24.00 Aluminium Composite Panel (ACP) with cylinder standoff supports and fiber 4.00 Each 13574.40

LED backlight panel system.

NADIAD MUNICIPAL CORPORATION - NADIAD

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF BOOK SCLUPTURE, BEAUTIFICATION AND ELECRTRICAL WORK AT DABHAN FOR NADIAD MUNICIPAL

Sr. No. Description Qty Unit Rate Amount

Providing and erecting 2.00 metre high temporary barricading at site; each

panel of size 2.50mx2.00m made of 40x40x6mm angle iron or 50x50x3mm

hollow MS tube posts/horizontal members/bracings

covered with 1.63mm thick MS sheet. The sheet shall be fixed with 30x5mm

MS flat by suitable welding/riveting. The panels shall be

made so that gap of 50cm above the ground is available making overall height

as 2.5m. MS channel ISLC 75 @ 5.70 kg/m, 50cm long shall be provided at the

bottom having oval shaped holes of size 50x25mm at both ends with 50cm

long MS angle 40x40x6mm bracing. Suitable arrangement shall be made to fix

the barricading to avoid from overturning by providing 250mm long expansion

25.00 at both ends. The work shall be executed as per drawing/direction of Engineer- 200.00 Rmt 2855.67

in-Charge which includes writing and painting, arrangement for traffic

diversion such as traffic signals during construction at site

for day and night, glow lamps, reflective signs, marking, flags, caution tape as

directed by the Engineer-in-Charge. The barricading provided shall be retained

in position at site continuously i/c shifting of barricading from one location to

another location as many times as

required during the execution of the entire work till its completion.

Rate include its maintenance for damages, painting, all incidentals,

labour materials, equipments and works required to execute the job.

The barricading shall not be removed without prior approval of Engineer

Dewatering by pumping set of required capacity including temporary platform

26.00 carting pumping at site and fixing the same in position including all accessories. 100.00 HP/hr. 18.50

and fuel and labour etc. complete.

Providing and fixing post and pipe railing as per detailed drawing including

coats of painting to steel works complete

Providing and stacking of Calliandra, emarginata of height 45-60 cm. in earthen

pot of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Calliandra hybrida of height 75-90 cm. with 4-5

branches in bag ofsize 25 cm as per direction of the officer-in-charge.

Providing and stacking of Cassia biflora of height 60-75 cm. with 4-5 branches

30.00 in poly bags of size 25 cm as per direction of the officer-in-charge. 100.00 Each 55.55

Providing and stacking of Cassia laevigata of height 45-60 cm. in earthen pots

of size 20 cm as per direction of the officer-in-charge.

32.00 Providing and Fixing Paver block M250 Grade 60mm Thick 1080.00 Smt 460.78

NADIAD MUNICIPAL CORPORATION - NADIAD

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF BOOK SCLUPTURE, BEAUTIFICATION AND ELECRTRICAL WORK AT DABHAN FOR NADIAD MUNICIPAL

Sr. No. Description Qty Unit Rate Amount

2mm Aluminium / 4mmACP sheeting fixed with Type-4 Class B High Intensity

33.00 Grade Sheeting as per IRC 67 : 2012 reflective sheeting of size including 202.50 Smt 4709.71

lettering and signs as applicable

Total Amount Rs:-

Total Amount Rs:-

Say Amount Rs:-

Consultanting Civil Engineer

DD(OPC) PVT. LTD.

City Engineer Chief Accountant

Nadiad Municipal Corporation Nadiad Municipal Corporation

Dy. Municipal Commissioner Dy. Municipal Commissioner

Nadiad Municipal Corporation Nadiad Municipal Corporation

NADIAD MUNICIPAL CORPORATION - NADIAD

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF BOOK SCLUPTURE, BEAUTIFICATION AND ELECRTRICAL WORK AT DABHAN FOR NADIAD MUNICIPAL

ELECTRICAL WORK

Sr. No. Description Qty Unit Rate Amount

Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or

required depth for laying any size of cable or locating the fault all over the run

and back filling the same and making the surface as normal ground.

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand /

Solid Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps

2.00 or in existing trench / pipe of following size of cables 210.00 Mtr. 161.60

(C) 4 core 10 Sq. mm

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary connecting accessories

of same material at required depth in existing trench for laying of cable. below

ground / road surface for enclosing cable

'(A)50 mm outer dia

Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv

grade ISI marked copper wires of following size to be erected as directed.

'(e) 1.50 Sq.mm 3 core round PVC sheathed

4.01 ---- As Above----- 2.50 Sq.mm 3 core round PVC sheathed 50.00 Mtr. 83.83

Supplying & erecting earth pit of minimum bore dia.150mm size approved

make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of

50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-

250 Micron galvanising, connection terminal dia of 12mm with constant ohmic

value surrounded by highly conductive compound with high charge dissipation

suitable for following type of applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate including value of earth

resistance of installation duly stamped and signed by agency and officer

Incharge has to ensure the value of earthing resistane mentioned in test

5.00 Certificate) & having back filling compound of (B) Inner chemical (CCM 1.00 Ea 10188.88

Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017,

Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill

Compound :- Earthing compound should be capable to retain moisture for long

time Necessary test report must be submitted by Agency.

'(c) For Electrical Installation covering Transformer Neutrals, Lightning arrester

Earthing, A.C.Plant & Sensitive Computer System(like Automation, SCADA) i.e

independent Earthing in normal soil.

Length of Pipe : 3.00 mtrs

Back filling Compound :2 nos Bags of 25 Kg.

Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms. dia.

6.00 galvanised iron pipe with coupling and buch buried in specially prepared earth 8.00 Ea 434.30

pit complete with necessary 8 SWG earth wire.

Providing and erecting ,Fabricating the box type items made from M.S. Sheet

with A.I. supports, wings, doors, handles other hardware materials as per

7.00 requirement design with finishing by three tank powder coating processed 80.00 Kg. 212.10

inside and outside painted, erected as directed including minor civil work.

NADIAD MUNICIPAL CORPORATION - NADIAD

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF BOOK SCLUPTURE, BEAUTIFICATION AND ELECRTRICAL WORK AT DABHAN FOR NADIAD MUNICIPAL

ELECTRICAL WORK

Sr. No. Description Qty Unit Rate Amount

Providing and erecting Approved make RCCBs conforming to IS: 12640 and

having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and

suitable for operation on 3 phase and neutral 415V,50Hz. having characteristic

8.00 of quick action & tripping with all advance feature & do not incorporate any 1.00 Ea 3585.50

electronic component for following Max. rating erected as directed.Cat III

'(iii) 63 Amps. FP Cat III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C

Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box

having following capacity

'(b)40 Amp. Cat III

9.01 --- As Above ----------- 63 Amp. Cat III 2.00 Ea 868.60

Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve)

having 10 KA breaking capacity & confirms to IS : 8828 in existing box having

following capacity

'(A) 6 to 32 Amp. Cat III

10.01 ------ As Above ----- 40 Amp. Cat III 1.00 Ea 348.45

Providing and erecting Miniature circuit breaker single pole 6A to 25A suitable

to operate on 240 V A.C. system and having breaking capacity 10 KA to be

erected in existing box. confirming to IS 8828/1996 with ISI Mark Cat III

Providing and erecting busbar chamber confirming to IS-375 fabricated from

G.M.S. sheet, dust & vermin proof having hinged door with rubber gasket and

necessary busbar supports with Aluminium busbar having current density not

more than 0.8 Amp. / sq.mm (Rated current / cross section area) duly wrapped

12.00 with colour insulation tape for phase sequence, three phase & neutral each 1.00 Ea 3070.40

Suitable for following current capacity with necessary painting mounted on wall

or pedestal frame of required size with necessary connections.

'(A) Suitable for 63/ 100 Amp. Capacity

Providing and erecting Approved make Four pole moulded case circuit breaker

having breaking capacity ICU of 25 KA. at 415 V,having normal current rating up

to 25 A to 100A. with Fixed thermal & magnetic release suitable to work on A.C.

supply 50 c/s. with all internal connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing. Cat III

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size

complete to be erected on/in wall or ceiling erected with necessary PVC

fittings & Junction boxes fixed with adhesive solution & Clamps with following

dia of pipes, in approved manner as directed Cat III

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of

coupling, PVC bushes, Check-nuts etc. complete of following sizes.Cat III

NADIAD MUNICIPAL CORPORATION - NADIAD

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF BOOK SCLUPTURE, BEAUTIFICATION AND ELECRTRICAL WORK AT DABHAN FOR NADIAD MUNICIPAL

ELECTRICAL WORK

Sr. No. Description Qty Unit Rate Amount

providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi

stranded, annealed copper conductor with heat resistant PVC insulated

conforms to IS 694, IEC - 227 erected in existing pipe of following size

16.00 (Specifically for control panel, relays, power switchgears, motor starters & 15.00 Mtr. 62.62

control wiring) with required size of copper lugs, nuts and bolts if required.Cat

One wire 6.00 sq. mm

16.01 ----- As Above ---- One wire 10.00 sq. mm 25.00 Mtr. 102.01

16.02 ---- As Above ---- One wire 16.00 sq. mm 35.00 Mtr. 158.57

Providing and erecting approved make light control unit suitable to operate on

230V +20% having ON/OFF delay time of 30-50 seconds and having facility for

17.00 Auto/manual system having two LDR lens to intensity light having capacity of 5A 2.00 Ea 2671.45

complete erected on section pillar with pipe and stand.

Supplying and erecting HYLAM sheet on existing angle iron frame.for following

18.00 thickness 2.00 sq.mtr 2272.50

Supplying & erecting approved make Digital time switch having lithium cell

years operative and operate battery backup 1 channel day clock with

memory programme, suitable to operate on 240V + 5%, 16A with, floating

contacts Minimum switching setup time 1 minimum & LCD display. Also

comprised permanent ON/OFF switching. Programming switches & housed in

fire proof thermoplastic enclosure & transparent cover erected as required

with necessary connection erected as directed.

Supplying & erecting power contactor ,AC3 duty for time switch complete

20.00 erected as per direction Cat III 3.00 Ea 3282.50

'(D) 4 pole 440V 40 Amp.

Supplying and erecting approved make single phase servo controlled voltage

21.00 stabilizer suitable for input voltage range 3 phase . And output voltage range 1.00 Ea 217150.00

225/235V. A.C.per phase complete erected. 80 Kva

NADIAD MUNICIPAL CORPORATION - NADIAD

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF BOOK SCLUPTURE, BEAUTIFICATION AND ELECRTRICAL WORK AT DABHAN FOR NADIAD MUNICIPAL

ELECTRICAL WORK

Sr. No. Description Qty Unit Rate Amount

Light Pole :- made out of 3- 4 mtr height structure is combination of daicast and

other decorative GI pole as approved by consultant, arrangement with base

plate for surface mounting The streetlight pole shall be of ‘composite’

construction designed to withstand specified ‘dead load’ pertaining to the

luminaire and its mounting accessories and ‘wind load’ corresponding to a basic

wind speed of 169kmph without any deformation or damage to the structure.

The pole should be designed as per the stipulations of standard EN40 to

establish its structural suitability under ‘serviceability’ and ‘ultimate limit state’

conditions. The pole should be provided with cast iron or wihout

embellishments as per the drawing. Pole Shaft should be fabricated out of Steel

tube of grade YSt 240 and batch test reports for chemical and mechanical

properties of material should be submitted along with the bid. Structurally

designed base plate of Steel A36/A572-50 or equivalent should be welded with

the pole shaft. The welding shall be of high quality, carried out by qualified

welders using approved welding procedures and tested for its quality through

NDT method, such as DP Test. The successful bidder should submit the test

reports before delivery of the material. The pole shall be provided with an

22.00 opening at the bottom with removable cover for providing LILO connectors, 8.00 Ea 15655.00

MCB, etc. (to be supplied by others). Appropriate reinforcement shall be

provided to compensate for the loss of section at this point to ensure overall

structural stability of the pole under specified operating conditions. The pole

shaft structure shall be hot dip galvanized through single dip process as per

ASTM A123 and minimum average coating shall not be less than 65 microns. No

mechanical operation, such as welding, drilling, etc. should be carried out on

the pole structure post hot dip galvanizing. Poles using pre galvanized steel

tubes or hot dip galvanized through double dip process are not acceptable.

Complete pole shall be treated with high quality primer and thereafter coated

with Polyurethane paint to minimum average DFT of 70 microns. The painting

shall be carried out by experienced and trained technicians using proven and

established painting procedure. Only ‘controlled’ paint drying process shall be

used to ensure proper adhesion and finish of the paint.4M height pole

matching as technenical specification and should be compatible to intall CCTV

or PA system on the Pole.

NADIAD MUNICIPAL CORPORATION - NADIAD

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF BOOK SCLUPTURE, BEAUTIFICATION AND ELECRTRICAL WORK AT DABHAN FOR NADIAD MUNICIPAL

ELECTRICAL WORK

Sr. No. Description Qty Unit Rate Amount

Supply of LED Light Supply, erecting, testing & commissioning of Decorative

Luminaires for Urban lighting, body made of painted spun aluminium, The

protector is made of polycarbonate grade UVresistant (IK 09- presented with IS

10322 report from 3rd NABL approved lab), Permanently sealed optical

compartment (comply by presenting technical data sheet ) with IP66 protection

( presented with IS10322 report from 3rd party NABL approved lab). Luminaire

offers tool free access to gear compartment with IP65 protection. Luminaire

can be installed as a suspended luminaire. The luminaire is equipped with

PMMA lenses with wide photometry for increased pole spacing.The luminaire is

provided with disconnector to avoid electrical shocks.Easy access to control

gear compartment by

23.00 opening special latch kind of arrangement .Luminaire is provided with built in 32.00 Ea 14695.50

under/over voltage protection Fixture is having a surge protection of 10KV.

Electronic driver is having power factor>0.90*, THD<20*% and input voltage

range from 120-227V AC at 50Hz. Luminaire efficacy is 120 im/ watt system

lumen 3600 lumen ( presented with LM79 report from 3rd party NABL lab ) in

CCT range of 4000 as per ANSI. System life of 50000 burning hours with 70% of

initial lumens maintained. Luminaire is suitable for operating temperature (Ta)

from -20 to 50c. Driver can withstand 320V AC for 48 hours and 360 V AC for

hours. the offered luminar must have BIS certificate including Junction Box IP

SITC Of 9-11 meter area lighting pole with 6 nosx45 watt round projector with a

lights including antiglare snoots, 2000 lumens, 30° beam a contemporary

design that is both timeless and unique in its impression.Compact without

visible mounting equipment and optimised integration,Polar is in perfect

continuity with the geometric lines of the square column.These assemblies are

ideal for surroundings of contemporary architectural constructions.Integrated

with LED Modules. Polycarbonate optical lens. Protection class IP65. Integral

power supply. Earth connection. Safety class I. CE- Conformity mark. Pole made

of Mild Steel. Pole design parameters vary depending on the type of bracket

24.00 and loading factor. All pole sections are welded using special v groove 1.00 Ea 298606.50

technique by certified welders using high end MIG welding processes. Built-in

control box with cast aluminium service door and safety rope. The control gear

tray is prewired with MCB,terminal connectors for loop-in / loop-out

arrangement. The foundation bolt holes in the base plate are designed to be

elongated for fine adjustments / alignment of the pole during installation. Base

plate made of steel grade E250 & foundation bolt of grade 4.6. K Lite KP-1063.

Supply of approx 15 W/M, 24/12/240V flexible RGBW LED homogenous profile

luminary for exterior top crown structure wash application. The housing of the

material should be made of PCB Silicon Tube and the LEDs should be SMD type.

The delivered lumen output of the fixture should be around 30lm/W. Power

output of the fixture should be approx 10-20W/M.The protection rating of the

25.00 fixture should be IP67. Power output of the fixture should be . The fixture 100.00 Rmt 4393.50

should be of beam distribution of 120˚. Fixture should be RGBW. The width and

height of the fixture should be around 12mm and 10mm respectively. Fixture

should come with rigid Installation Aluminium U profile / Difusser / Splitter &

Decoder as per site requirement.

NADIAD MUNICIPAL CORPORATION - NADIAD

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF BOOK SCLUPTURE, BEAUTIFICATION AND ELECRTRICAL WORK AT DABHAN FOR NADIAD MUNICIPAL

ELECTRICAL WORK

Sr. No. Description Qty Unit Rate Amount

SITC of 16-30 watt W.W Projector Light LED Luminaire of Surface Mounted

Luminari system , made with low copper content extruded aluminum housing,

Electro statically applied polyester powder coat finish along with machined

aluminum end caps, and a silicon gasket. The fixture should have stainless steel

hardware and clear tempered glass. Lumen maintenance should be L80 B10

1,00,000 hrs or higher. IP66 min. with the impact resistance of IK06 min. The

operating temperature range should be -5° C to 50° C. Fixtures should be

available with various mounting options as per site requirements, Custom Color

finish as per consultant request. Fixtures should have a dual chamber thermal

26.00 design system that allows air to flow between the driver and LED board, 13.00 Ea 9595.00

maximizing the surface area, and increasing output and the driver should be

replaceable. The Wattage of the fixture should be 16-30W/ , Version runs on

direct 230VAC/ DC 24 V. The fixture should have delivered a lumen output of

2200lm min. . The fixture should have the flexibility to integrate optics with

different beam distributions within the same Electrical board of one fixture. The

fixture should have a beam angle of 10°/ 15°/ 20°/30°/45°/ 60° /

15°x32°/10°x45°. The fixture should have the dimension Dimensions approx

to 200 mm. Fixture Should be complaint to LM-80.

Total Amount Rs:-

Total Amount Rs:-

Say Amount Rs:-

Consultanting Civil Engineer

DD(OPC) PVT. LTD.

City Engineer Chief Accountant

Nadiad Municipal Corporation Nadiad Municipal Corporation

Dy. Municipal Commissioner Dy. Municipal Commissioner

Nadiad Municipal Corporation Nadiad Municipal Corporation

NADIAD MUNICIPAL CORPORATION - NADIAD

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF BOOK SCLUPTURE, BEAUTIFICATION AND ELECRTRICAL WORK AT DABHAN FOR NADIAD MUNICIPAL

PATHWAY DECORATIVE POLE WITH WIRING ALONG WITH DABHAN CIRCLE

Sr. No. Description Qty Unit Rate Amount

Providing and fixing 4.0 Meter high Decorative MS Pole fabricated from heavy-

duty Mild Steel (MS) pipe of 76 mm outer diameter (acceptable range 65–76

mm) with minimum wall thickness of 2.5 mm, including base plate of 200 mm

× 200 mm × 8 mm thick MS plate, fully welded and ground smooth. The pole

shall be complete with internal DIN rail mounting arrangement for

MCB/junction connection fixed on standoffs, cable entry provision at base, and

earthing terminal. The entire assembly shall be finished with outdoor-grade

polyester powder coating (minimum 60–80 microns) in black or grey color for

corrosion resistance and aesthetic appearance. Total Pole Weight 20 Kg.

40W Post top lantern type light fixtur

Providing, supplying, and fixing Post Top Lantern Type LED Light Fixture of

Watt, suitable for mounting on decorative pole, made of die-cast aluminum

housing with powder-coated finish, having IP65 or higher protection and IK07

impact resistance, with integrated driver, suitable for operation on 230V ±10%,

50Hz AC supply. The fixture shall have high-efficiency LED chips with system

lumen efficacy ≥ 110 lm/W, color temperature 3000K–6000K, and CRI ≥70. The

fitting shall include necessary mounting accessories and complete internal

wiring, testing, and commissioning as per engineer-in-charge directions

Providing 1:2:4 cement concrete foundation & 70 % PCC from bottom

including excavation for the pole of size 45 x 45 x 100 cm. Deep in below

2.00 ground level with plinth of 45 cm x 45 cm (or 45 cm dia x 45 cm) high upper 66.00 Each 809.01

ground level with necessary curing and finishing in approved manner. ( for 4 &

Providing & erecting fibre reinforced PVC flexible pipe with brass locking nuts &

3.00 washers & clips at both ends complete erected without leakage 330.00 Rmt. 181.80

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be erected

4.00 concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS 264.00 Rmt. 82.82

PVC insulated stranded wire of green colour for earth continuity of following

size (c) 3 wire 1.5 sq. mm

Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve)

5.00 having 10KA breaking capacity & confirms to IS :8828 in existing box having 66.00 Each. 578.73

following capacity (a) 6 to 32 Amp. Cat.III

Painting of Decorative Light Pole having post top lantern complete with PU

base primer and PU Paint on pole.

Supplying & erecting IP 55 grade following size section pillar fabricated from

joint less M.S. Sheet with angle iron legs made from jointless M.S. Angle with

cable clamps to be buried in ground to have appropriate erection to work

uniform until erected with cement concrete foundation and 45 cm high bricks

work finishing with plaster etc. hinged double door internally supported on

both side, with internal and outside looking arrangement with look and keys in

7.00 duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos. one is welded and other with 2.00 Each 3595.60

nut and bolt for erecting Bakelite sheet. Painting the Section Pillar inside and

out side with three tank powder coated paint. section pillar roof should be

without joint with water leakage proof & tested as per IP 55 test & followed by

IS 2147 of 1962 (B) 75 X 60 X 45 cm section pillar fabricated from 16 Gauge MS

Sheet with angle iron legs 45 cm long made from 35 X 35 X 5 mm thick MS

Supplying and erecting nuwood 12 mm thick on existing angle iron frame.

NADIAD MUNICIPAL CORPORATION - NADIAD

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF BOOK SCLUPTURE, BEAUTIFICATION AND ELECRTRICAL WORK AT DABHAN FOR NADIAD MUNICIPAL

PATHWAY DECORATIVE POLE WITH WIRING ALONG WITH DABHAN CIRCLE

Sr. No. Description Qty Unit Rate Amount

Supplying & erecting approved make Digital time switch having lithium cell

years operative and operate battery backup 1 channel day clock with

memory programme, suitable to operate on 240V + 5%, 16A with, floating

contacts Minimum switching setup time 1 minimum & LCD display. Also

comprised permanent ON/OFF switching. Programming switches & housed in

fire proof thermoplastic enclosure & transparent cover erected as required

with necessary connection erected as directed.

Providing and erecting approved make light control unit suitable to operate on

230V +20% having ON/OFF delay time of 30-50 seconds and having facility for

10.00 Auto/manual system having two LDR lens to intensity light having capacity of 2.00 Nos. 2265.43

5A complete erected on section pillar with pipe and stand.

Supplying & erecting power contactor ,AC3 duty for time switch complete

erected as per direction Cat III (D) 4 pole 440V 40 Amp.

Providing and erecting Approved make Four pole moulded case circuit breaker

having breaking capacity ICU of 35 KA. at 415 V. having normal current rating

125A. with Fixed thermal & magnetic release suitable to work on A.C.supply

c/s. with all internal connections, spreader tinned copper & complete erected

in existing 16 G.M.S. housing. ICS=100% of ICU only Cat III

Providing and erecting Approved make Four pole moulded case circuit breaker

having breaking capacity ICU of 25 KA. at 415 V,having normal current rating

up to 25 A to 100A. with Fixed thermal & magnetic release suitable to work on

A.C. supply 50 c/s. with all internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing. ICS=100% of ICU only Cat

Providing and erecting Approved make RCCBs conforming to IS: 12640 and

having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and

suitable for operation on 3 phase and neutral 415V,50Hz. having characteristic

of quick action & tripping with all advance feature & do not incorporate any

electronic component for following Max. rating erected as directed. Rating -

Providing and erecting AC-3 duty 3 pole power contactor with 2 NO & 2 NC aux

15.00 contacts complete with 415V/220V operating coil suitable for . (B) for 40 A 2.00 Each 4793.46

Providing and erecting Approved make Earth fault Relay suitable to mount with

inter connection suitable to following size of moulded case circuit breaker

16.00 having CT ratio & MCCB rating as following along with shunt trip 220V AC. with 2.00 Nos. 4687.41

all internal connections & complete erected in existing M.S.housing. (1) 15 A -

100 A , CT Ratio 1/100

Supplying and erecting triple pole & neutral 440V/ 500V panel mounting

Aluminium Busbars with four equal Nos. of bus having current density not

more than 0.8 Amp. / sq.mm (Rated current / cross section area) duly wrapped

with colour insulating tape for phase sequence of following current carrying

capacity, erected with necessary bus bar supports /insulators, main cable

socket to each busbar,erected in existing cubical panel with necessary

connections.(A) Suitable for 100 Amp. Capacity

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C

18.00 Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box 2.00 Nos. 737.30

having following capacity (c)63 Amp. Cat.III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C

19.00 Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box 6.00 Nos. 668.62

having following capacity (b)40 Amp. Cat.III

NADIAD MUNICIPAL CORPORATION - NADIAD

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF BOOK SCLUPTURE, BEAUTIFICATION AND ELECRTRICAL WORK AT DABHAN FOR NADIAD MUNICIPAL

PATHWAY DECORATIVE POLE WITH WIRING ALONG WITH DABHAN CIRCLE

Sr. No. Description Qty Unit Rate Amount

Pro. & erecting electronic overload relay with single phasing preventer [a] for

Supplying & erecting in earthpit of minimum bore dia. 150mm size approved

make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of

mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250

Micron galvanising, connection terminal dia of 12 mm with constant ohmic

value surrounded by highly conductive compound with high charge dissipation

suitable for following type of applications with chamber and heavy duty

cover.(approved make OEM has to submit test certificate including value of

21.00 earth resistane of installation.) & having back filling compound of (B) Inner 2.00 Nos. 4591.46

Chemical (CCm Compound) - Resistivity :- 0.2 Ohm/meter testing as per IEC

62561-2017 , Voltage Drop :- < 1 volt at no load & dry form , Sulpher content :-

<2% .(C) Back filling copound :- Earthing compound should be capable to retain

moisture for log time. Necessary test report must be submitted.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms.

22.00 dia. galvanised iron pipe with coupling and buch buried in specially prepared 66.00 Nos. 823.15

earth pit complete with necessary 8 SWG earth wire.

23.00 For using salt and charcoal / coke as required for pipe type earthing. 66.00 Nos. 171.70

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or

in existing trench / pipe of following size of cables(C) 4 core 10 Sq. mm

Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or

required depth for laying any size of cable or locating the fault all over the run

and back filling the same and making the surface as normal ground.

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II)with necessary connecting accessories

26.00 of same material at required depth in existing trench for laying of cable. 1200.00 Mtr. 62.62

below ground / road surface for enclosing cable (A) 50 mm outer dia

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of

following size evenly crimped with high pressure tool & connected to

switchgear terminals with brass/cadmium plated nut bolts in an approved

manner. (A) 1.5/ 2.5/4/6 Sq.mm

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of

following size evenly crimped with high pressure tool & connected to

switchgear terminals with brass/cadmium plated nut bolts in an approved

manner.(B) 10 Sq.mm

Providing and, fixing heavy duty flange type brass double compression type

cable gland with rubber ring for PVC insulated armoured cable complete with

out going tails, insulating tape etc for following size of cables.(A) 3 & 1/2 /

30.00 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. 50.00 Kg. 794.87

Providing and erecting required size HOT deep Galvanised iron strip for

31.00 earthing of H.T. , OCB/ ACB/ Transformer LT panel board, Motors etc. using 150.00 Kg. 77.77

Total Amount Rs:-

Total Amount Rs:-

Say Amount Rs:-

NADIAD MUNICIPAL CORPORATION - NADIAD

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF BOOK SCLUPTURE, BEAUTIFICATION AND ELECRTRICAL WORK AT DABHAN FOR NADIAD MUNICIPAL

PATHWAY DECORATIVE POLE WITH WIRING ALONG WITH DABHAN CIRCLE

Sr. No. Description Qty Unit Rate Amount

Consultanting Civil Engineer

DD(OPC) PVT. LTD.

City Engineer Chief Accountant

Nadiad Municipal Corporation Nadiad Municipal Corporation

Dy. Municipal Commissioner Dy. Municipal Commissioner

Nadiad Municipal Corporation Nadiad Municipal Corporation