Special repairs to married accn block No 35 1 to 8 Type I at Race Course under GE North Ambala Cantt

Amount

SCHEDULE A PART I (B/R WORKS)

Demolition of concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) including floor tiles, screed bed etc complete all as specified and as directed.

Material and labour for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust,etc. and brushing the surface with neat cement slurry @ 3.0kg of cement per sq. metre complete all as specified and as directed.

Material and labour, 25 mm thick, PCC (1:2:4) type B0 (using 12.5 mm graded stone aggregates) as in sub base of floors, finished rough and even to receive floor topping complete all as specified and as directed.

Material and labour for PCC 1:3:6 type C-1 (using 20 mm graded mechanically crushed stone aggregate), 50mm thick, as in plinth protection/PCC path and paving, laid in panels of area not exceeding 1.20 sqm with 12mm wide joints filled with mastic (using bitumen and sand mixture applied hot in the ratio of 1:3 by weight) formed at the end of each panel and change in direction of plinth protection/PCC Path and paving and finishing the top surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for premium quality, joint free, coloured ceramic tiles (Square/ rectangular), area of each tile exceeding 0.18 sqm and not exceeding 0.36 sqm and 7 to 8 mm thick, laid in floor over and including cement screed bed 15mm thick in cement mortar (1:4) and set and jointed in neat cement slurry @ 3.00 kg/Sqm and pointed in white or coloured cement to match the tile colour complete all as specified and directed.

Material and labour for Premium quality, joint free, non skid coloured ceramic tiles 7mm to 8mm thick, of same description and length as of floor tile but 150 mm height on vertical surfaces of walls including 10mm thick rough finished plaster in cement mortar (1:3) set jointed in neat cement slurry and pointed in coloured cement to match ,complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for premium quality, coloured ceramic tiles, area of each tile exceeding 0.11 sqm and not exceeding 0.18 sqm, on vertical surfaces of walls over and including 10mm thick rough finished plaster in cement mortar (1:4), set, jointed in neat cement slurry and pointed in coloured cement to match tile colour complete all as specified and directed. Note:- Size of tile shall be cut as required.

Material and labour for premium quality, glazed coloured ceramic tiles of size 450 x 350 x 7mm thick or 350mmx250mmx7mm thick, on vertical surfaces of walls over and including 10mm thick rough finished plaster in cement mortar (1:4), set, jointed in neat cement slurry and pointed in coloured cement to match tile colour complete all as specified and directed. Note:- Size of tile shall be cut as required.

Material and labour for marble work, Baroda green, 16-18mm thick, one piece in width and length not less than 1.8 m (except in case of slab is more than 1.80 metre and less than 2.40 metre smaller size as approved by Engr-in-Charge may be used), laid over and including 15mm thick bedding layer in cement mortar (1:4), table rubbed & polished in shelves etc including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of marble including rounding of front edge and finally granite finish polishing with and including taking down the existing slab of any type complete all as specified and as directed.

Demolition of reinforced concrete (other than ground floors) as in roofs, floors, beams, staircases, landing, chajjas and similar suspended work, reinforcement cut as required to facilitate demolition complete all as specified and directed.

Material and labour for pre-cast cement concrete (1:2:4), type B1, using 20mm graded stone aggregates, as in landings, cover slabs (for man holes etc.), balconies, canopies, deck slabs and shelves and the like including use and waste of formwork and set in cement mortar (1:4) complete all as specified and directed.

Material and labour for reinforced cement concrete (1:2:4), type B1, using 20mm graded stone aggregates, as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Material and labour for reinforced cement concrete (1:2:4), type B1, using 20mm graded stone aggregates, as in chajjas complete all as specified and directed.

Material and labour for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick, for rough finished, horizontal or sloping, flat surfaces of concrete complete all as specified and directed.

Material and labour for formwork to to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.for rough finished, flat surfaces of concrete complete all as specified and directed.

Material and labour for formwork to to chullah hoods, chajjas, troughs and similar items including edges, for rough finished, flat surfaces of concrete complete all as specified and directed.

Material and labour for mild steel TMT bars of 10mm dia and over, as in reinforcement, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Material and Labour for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth in brick walls, complete, all as specified and as directed.

Dismantling of brick work or stone masonary, precast cement concrete walling built in cement mortar including all quoins, arches, pillars etc., complete, all as specified and as directed.

Material and labour for brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 metre mean radius, built in cement mortar (1:6) complete all as specified and as directed.

Material and Labour for Brick work with sub class ‘B’ bricks (Except Bricks), straight or curved on plan exceeding 6 metre mean radius, built in cement mortar (1:6) , complete all as specified. ( Note- The serviceable bricks obtained from Serial item No- 1.20 will be used after removing motar, cleaning the bricks with water, etc.)

Material and labour for brickwork, with sub class 'B' bricks, straight or curved on plan to any radius, in half brick thick walls, built in cement mortar 1:4 complete all as specified and as directed.

Taking down cement or cement lime plaster, of any description, on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and as directed.

Material and labour for rendering, 10 mm thick, in cement mortar 1:3, on ceiling, finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for rendering 15 mm thick on surface of any description of brick work or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement all as specified and as directed.

Material and Labour for 15mm thick rendering on surface of any description of brick work, concrete surfaces in cement mortar 1:4 mixed with WPC @2% by weight of cement or as per manufacturer’s instructions, finished even and fair, complete, all as specified and as directed. (Note : WPC shall be measured and paid separately)

Supply only integral water proofing compound complete all as specified and as directed.

Material and labour for preperation of old plastered or unplastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

Material and labour for preperation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed.

Material and labour for preperation of old plastered surfaces of walls and applying two coats of white wash complete all as specified and as directed.

Material and labour for preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed.

Material and labour for preparation of old plastered wall surfaces and applying two coats of cement base paint complete all as specified and as directed.

Material and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper with hand roller, over a coat of primer over 2-3mm thick wall care putty , complete all as specified and as directed.

Material and labour for complete removal of existing treatment on surfaces of wall by using appropriate technique as approved by Engr-in-charge for complete removal of all layers of old treatment and reaching upto old plastered surface and applying two coats of oil bound distemper with hand roller, over a coat of primer over 2-3mm thick wall care putty , complete all as specified and as directed.

Material and labour for complete removal of existing treatment on walls including washing down, rubbing down and applying anti-fungal treatment as required and applying two coats of weather shield Acrylic exterior paint over a coat of primer, complete all as specified and directed.

Supply and fix in repairs, stainless steel decorative curtain rod, 20mm dia, fixed with decorative brackets, stop roller and finials at the end etc. including taking down of existing unservicable curtain rod of any type and pattern complete all as specified and as directed.

Supply and fixing in repair stainless steel sink 1.00mm thick, ISI marked for kitchen with plug, waste PVC pipe, washers including cantilever cast iron brackets connecting union waste pipe with drainage board over all size 940 mm x 460 mm with bowl size 405 mm x 354mm x 203 mm etc, complete all as specified and as directed by the Engineer-in-Charge. (Make :PRAYAG Cat No-1240-D (Solitaire Range) or equivalent model in makes mentioned in Appendix 'B' of tender document ) Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supplying & Fixing for stainless steel plate rack standard size 1000mmx750mm complete and fixing with rawl plug and steel screws of wt not less than 8 kg each, complete, all as specified and as directed by the Engineer-in-Charge. (Make : Prayag Cat No. P-330 or equivalent model in makes mentioned in Appendix 'B' of tender document )

Taking down chowkats or frames with shutter, area not exceeding 1.50 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes in wall/concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM (1:3) and finishing the surfaces to match with existing finish complete all as specified and directed.

Taking down chowkats or frames with shutter, area exceeding 1.50 Square metre and not exceeding 4.00 Square metre (without taking off shutters from frame) and removing from site, including cutting holes in wall/concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM (1:3) and finishing the surfaces to match with existing finish complete all as specified and directed.

Supply and fixing of solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

Supply and fixing factory made Solid PVC Moulded Door Shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face complete supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

SSupply and fixing Factory made pressed steel frameof size 105 x 60 mm for doors, fabricated from 1.25 mm thick sheet, with one or more rebate including necessary fixing lugs, hinges, lock strike plate, etc. including sanding, tarring backs of chowkhats, one shop coat of primer and, PCC 1:3:6 type C-0 filling as in back of chowkhats complete all as specified and directed.

SSupply and fixing Factory made pressed steel frameof size 125 x 60 mm for doors, fabricated from 1.25 mm thick sheet, with one or more rebate including necessary fixing lugs, hinges, lock strike plate, etc. including sanding, tarring backs of chowkhats, one shop coat of primer and, PCC 1:3:6 type C-0 filling as in back of chowkhats complete all as specified and directed.

Supply only mild steel butt hinge of 100mm length, cold rolled, medium weight, ISI marked complete all as specified.

Supply only mild steel butt hinge of 50mm length, cold rolled, medium weight, ISI marked complete all as specified.

Supplying and fixing of factory made 35mm thick, 2nd class HW, plain framed, panelled shutters (two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply and fixing of second class hard wood, 35mm thick, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, elc.;sizesof me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

Supply and fixing of galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

Supply and fixing of steel window box type, with side hung shutters, using ERW hollow 'P' section, factory made, comprising double frame for and including gauged and glazed skeleton shutter, 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs etc. all as shown on drawing No. TD-219 (c) sheet 1/3 to 3/3 and applying two coats of approved colour synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. Note: (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frame shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery and grill 10 mm square bar irrespective of whatever shown on drawings including painting (iii) Glazing, wire mesh and painting shall be measured and paid for separately.

Supply and fixing of steel ventilator box type, with side hung shutters, using ERW hollow 'P' section, factory made, comprising double frame for and including gauged and glazed skeleton shutter, 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs etc. all as shown on drawing No. TD-219 (c) sheet 1/3 to 3/3 and applying two coats of approved colour synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. Note: (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frame shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery and grill 10 mm square bar irrespective of whatever shown on drawings including painting (iii) Glazing, wire mesh and painting shall be measured and paid for separately.

Supplying & Fixing for mild steel door shutter two leaves with frame of 20 gauges MS sheet ( all arround) and leaves of 21 gauge MS steel ( all as per Godrej pattern) including locking arrangement with mortice lock of mild steel, vertical type, 65mm size, 2 lever, ISI marked with duplicate keys and handle, etc. (all as per Godrej pattern) including two coats of spray painting over a coat of red oxide primer complete fixed on brick or concrete wall with minimum six numbers of 10mm dia and 100mm long mild steel bolt with washer and nut in cement mortar (1:4) or PCC 1:2:4, type B-0, complete all as specified and directed by Engineer-in-Charge.Note : Area of opening shall be measured.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

Material and labour for MDF Board prelaminated both side, 18mm thick, exterior grade (grade-I) conforming to IS-14587, fixed with srews for kitchen cupboard and cabinet, shelf for cupboard, including hinges, brass handle and all necessary items complete all as specified and directed. Make- Geenply, Century, Kitply

Material and labour for small fittings of 1st class hard wood, such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessaty' labours; articles not exceeding 200 cu. cm each complete all as specified and directed.

Supplying and Fixing mild steel helical door spring 150 mm long fixed to wooden chowkhats or welded to angle iron/ steel door frames, complete, all as specified and as directed.

Supply and fixing of grating doom 125 mm dia with waste hole of PTMT.(Minimum weight 40gms) complete all as specified and directed.

Supply and fixing of 150 mm long, aluminium handle, cast type, anodized, ISI Marked complete, all as specified and as directed.

Supply and fixing of 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed.

Supply and fixing of mild steel cold rolled butt hinges, 100 mm long, medium weight and fixed complete all as specified and as directed.

Supply and fixing of 300 mm long aluminum anodised sliding door bolt, ISI marked, with hasp, staple (bolt type) complete with clamps bolt not less than 12mm dia and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolt of extruded section or cast aluminum alloy with minimum of 6 bolts and nuts, four on bolt plate and two on plate complete all as specified and as directed.

Material and labour for preparing new wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of approved colour synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

Material and labour for preparation of new steel surfaces, of any description not otherwise described, over 10 cm width or girth and applying two coats of approved colour synthetic enamel paint complete all as specified and as directed.

Supply and fixing of sheet glass, 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 sqm in each pane complete all as specified and directed.

Supply and fixing of sheet glass, 3mm thick, figured glass, pin head type and glazing with oil putty in squares not exceeding 0.5 sqm in each pane complete all as specified and directed.

Taking up or down 15mm bore, steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 20mm bore, steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Supply and fixing of GI tubing, ISI Marked, 15mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Supply and fixing of GI tubing, ISI Marked, 20mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Fixing only in repairs 15mm dia GI tubes, any grade, to walls and ceilings or laying in floors complete all as specified and as directed. Note: Old tubes reteived from serial item No 1.70 hereinbefore shall be reused in this item.

Fixing only in repairs 20mm dia GI tubes, any grade, to walls and ceilings or laying in floors complete all as specified and as directed. Note: Old tubes reteived from serial item No 1.71 hereinbefore shall be reused in this item.

Cutting into existing manholes for connecting new drains, and making good to pipe and rendering cutting out existing benching for and forming branch channel( 1/2 round or 3/4 section ) in cement concrete 1:2:4 type B-1 (using 20mm size crushed stone aggregate) smooth finished and reforming benching as required of pipe 100 mm dia, complete all as specified.

Supply and fixed (in repair), stop valves, 15 mm dia pipe, chromium plated, fancy type, ISI marked, screwed down, high pressure with capstan head, (concealed type) with long shank, screwed both ends for iron pipes or for unions, complete, all as specified and as directed. (Note : Weight of stop valve shall not be less than 0.575 Kg) Make-ESSCO Cat No ES-514-A or equivalent model in makes mentioned in Appendix 'B' of tender document . (ii)Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supply and fixing in repair, angle cock, 15mm dia, cast copper alloy, chromium plated, ISI marked, screwed down, high pressure with capstain head, screwed both ends for iron pipes or for unions complete all as specified and as directed. Make-Prima Art No- PSP-504-A or equivalent model in makes mentioned in Appendix 'B' of tender document . Note: Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment.

Supplying and fixing ( in repair) stop cock 15mm dia, cast copper alloy, ISI marked, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified and as directed. Note : (Make : JAINKO Model No-SVE-1 or equivalent model in makes mentioned in Appendix 'B' of tender document ) (ii)Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supply and fixing in repair, bib tap, screwed down, high pressure, cast copper alloy, fancy type, chromium plated, ISI marked, with capstan heads, screwed down suitable for 15mm bore pipe or union complete all as specified and directed. Make- PRIMA Cat No PSP-501 or equivalent model in makes mentioned in Appendix 'B' of tender document. Note- Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment.

Supply and fixing (in repair), 15mm bore pillar tap, chromium plated cast copper alloy, ISI marked, with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks, complete, all as specified and as directed. (Note : Weight of pillar tap shall not be less than 0.665 Kg) Make-ESSCO Cat No ES-507-A or equivalent model in makes mentioned in Appendix 'B' of tender document . (ii)Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supplying and fixing ( in repair), stop cock 20mm dia, cast copper alloy, ISI marked, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions complete, all as specified and as directed. Note : (Make : JAINKO Model No-SVE-2 or equivalent model in makes mentioned in Appendix 'B' of tender document ) (ii)Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supplying and fixing (in repair), shower arm 240 mm long, light weight , round shape for wall mounted showers with wall flange suitable for 15mm bore pipe including overhead shower rose 125mm dia round shape single flow, complete all as specified and as directed by the Engineer-in-Charge. (Make : Cat No. BS-76 of Prayag or equivalent model in makes mentioned in Appendix 'B' of tender document ) Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supply and fixing of brass chromium plated tubular towel rail (finish Glossy), 20mm dia, D type, 60cm long between flanges complete all as specified and directed. Make- PRIMA Cat No PDX -4501 A or ESSCO Cat No-1111 or Prayag Cat No. BA-20 or equivalent model in makes mentioned in Appendix 'B' of tender document. Note- Contractor shall submit a guarentee certificate for tubular towel rail from manufacturer to Engineer-in-Charge before claiming payment.

Supply and fixing of PVC connections, 450 mm long and 15mm dia with brass fly nuts and PVC washers on both ends complete all as specified and directed.

Supply and fixing in repair, vitreous china wash hand basin, white colour, flat back, of size 550x440mm, ISI marked, with 2 Nos.CI brackets embedded in cement mortar 1:4, PVC waste pipe, 45cms long, fixed to walls, 15mm dia PVC connections and chromium plated waste coupling, etc., including taking down of existing unservicable wash hand basin of any type and pattern complete all as specified and directed.

Supply and fixing in repairs, vitreous china squatting pan of Orissa pattern, size 580mm x 440mm, white (Ist quality) with ‘P’ or ’S’ trap, with front or back inlet and integral foot rests of any pattern including provision of lime concrete for fixing and making good to existing floor surface and connection to flush pipe, trap, anti syphonage pipe, etc including taking down of existing unservicable squatting pan of any type and pattern complete all as specified and directed.

Supply and fixing in repairs of 10 litre capacity, virgin polypropylene cistern, ISI marked, coloured, low level, valveless syohonic action type, complete with PVC bend/flush pipe and making all connections including taking down existing high or low level unserviceable flushing cistern and making good the disturbed surface to match with the existing surface complete all as specified and directed.

Supply and fixing in repair, PVC floor trap, 100mm size, with CP grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1 including taking down of existing unservicable floor trap of any type and pattern complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, floor, wall etc.complete all as specified and directed.

Supply and fixing cast iron soil, waste and vent spun pipes100 mm bore, ISI marked, in any length, with or without ears, with cement joints,fixed to walls complete all as specified and as directed.

Supply and fixing cast iron soil, waste and vent spun pipes 75 mm bore, ISI marked, in any length, with or without ears, with cement joints,fixed to walls complete all as specified and as directed.

Supply and fixing cast iron soil, waste and vent spun pipes 100 mm bore, ISI marked, in any length, with or without ears, with cement joints, laid in trenches complete all as specified and as directed.

Supply and fixing cast iron soil, waste and vent spun pipes 75mm bore, ISI marked, in any length, with or without ears, with cement joints, laid in trenches complete all as specified and as directed.

Supply and fixing cast iron soil, waste and vent spun pipes 50 mm bore, ISI marked, in any length, with or without ears, with cement joints,fixed to walls complete all as specified and as directed.

Supply and fixing of cast iron bends (any radius), diminishing pieces or tapers (larger bore measured), 100mm bore, fitted with oval access doors complete all as specified and directed.

Supply and fixing of cast iron bends (any radius), diminishing pieces or tapers (larger bore measured), 75mm bore, fitted with oval access doors complete all as specified and directed.

Supply and fixing of cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, 75mm bore with oval access doors complete all as specified and directed.

Supply and fixing of cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, 100mm bore with oval access doors complete all as specified and directed.

Supply and fixing of cast iron vent cowl for 50mm bore of pipe complete all as specified and directed.

Supply and fixing of cast iron vent cowl for 75mm bore of pipe complete all as specified and directed.

Supply and fixing of salt-glazed stoneware gully traps, square or round mouthed, type 'P' of size 150mm x 150mm including setting and jointing in cement mortar (1:1) including demolition of old unservicable gully traps complete all as specified and directed.

Supply and fixing of mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if equired: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings heads, shoes, bends, swan-necks etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

Supply and fixing 110mm dia UPVC, rain water drain pipe, type ‘A’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified and directed.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing 110 mm bore PVC (SWR) plain bend/shoes, any radius including jointing with solvent cement complete all as specified and directed. Note- UPVC bends shall be conform to BS 4515 DIN 19531 and DIN 19534.

Supply and fixing in repair, water storage tank, 500 ltr capacity, HDPE triple layer, white coloured, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore, including taking down the unserviceable water tank and removing from site complete all as specified and as directed.

Dismantling of brick or terracing tiles of single layers on roofs and removal of unserviceable brick tiles from site, complete all as specified and as directed.

Demolition of mud in roof any thickness including leeping plaster and removal of the same outside defence land and cleaning the surfaces with wire brush complete all as specified and as directed.

Material and labour for plain cement concrete, 1:2:4 type B-0 (using 12.5 mm graded mechanical crushed aggregate) for benching, coving, roof kerbs , complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for water proofing treatment with following application over roofs surface complete, all as specified and as directed :- (i) Plain cement concrete 1:2:4 type B1, (using 20 mm graded stone aggregate) 50 mm thick (Average thickness ) as in levelling course,. and surfaces finished even and fair without using extra cement. (ii) Applying oil bound bituminous primer at the rate of 0.4 Litres/Sqm as per IS 3384-1986 on prepared surfaces of roof. Surface shall be kept free, till the primer is impregnated and the solvent oil in the primer get evaporated. (iii) Applying one coat of hot straight run bitumen grade 30/40 (Grade S-35) conforming to IS-73 at the rate of 1.2 Kg/Sqm. (iv) Laying 3mm thick APP polymeric water proofing membrane of weight not less than 3.6 Kg/Sqm, black finish reinforced with non woven polyster matt, wth a thermo fusible finish, torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturers instruction including preparation of surface. Note :- The water proofing treatment shall be carried out by the manufacturer or his authorised applicators in terms of clause 11.43 of MES Sch Part-I (2009) and in addition to gurantee as specified in CA, contractor shall also provide Guranttee for water proofing treatment from manufacturer / his authorised applicator, for the water proofing treatment carried out in the work.

Material and labour 40 mm thick brick tiles laid on and including 15 mm thick bedding layer in cement mortar 1:6 and joints grouted flush in cement mortar (1:3) mixed with 5% crude oil by weight of cement, complete all as specified and directed and flush pointed in cement mortar (1:3), complete all as specified and as directed .

.Demolition of un-reinforced cement concrete of any description and in any position, not otherwise specifically provided for and removal the rubbish/ demolished material outside defence land, complete all as specified and as directed

Material and labour for PCC (1:7:12) type F2 using 40mm graded stone aggregates as in foundation, filling and mass concrete for sunken portion complete all as specified and as directed.

Material and labour for filling broken bricks/brickbats under sunken portion in layers not exceeding 15 cm each, ramming to make compacted mass including removal of unservicable brickbats/filling outside defence land, complete all as specified and as directed

Material and labour for rendering 10mm thick on brick work or concrete surfaces in cement mortar 1:3, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for water proofing treatment with following application to sunken portion of WCs, bathroom, etc. surface complete, all as specified and as directed :- (i) Cleaning of roof surface with mechanical means i.e. wire brush/air blower etc. and remove all loose /unsound material,dirt,dust etc. (ii) First layer of cement slurry @ 0.488 Kg/sqm mixed with acrylic based polymer modified cementitous composite compound @ 0.253 Kg/sqm and allow it to dry for four hours. (iii) Second layer of cement slurry @ 0.242 Kg/sqm mixed with acrylic based polymer modified cementitous composite compound @ 0.126 Kg/sqm and allow it to dry for four hours followed with water curing for 48 hours by ponding.. (iv) Paste 200 micron thick polythene film with adhesive over treatment including sealing the joints/ traps/WC/Soil waste pipe with approved sealing compound.. Note :- The water proofing treatment shall be carried out by the manufacturer or his authorised applicators in terms of clause 11.43 of MES Sch Part-I (2009) and in addition to gurantee as specified in CA,

Material and labour for extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc.complete all as specified and as directed.

Material and labour for PCC (1:2:4) B-1 using 20 mm graded stone aggregates as in surface channel or drain including use of necessary from work for fair finished surface complete all as specified and as directed.

Material and labour for PCC 1:4:8 type D-2 (using 40 mm graded mechanically crushed stone aggregates), 100mm thick, as in sub base to floor etc., finished rough to receive topping layer complete all as specified and directed.

Material and Labour for vibratory compacted, precast cement concrete, coloured (other than grey), rubber moulded , interlocking designer paver blocks( double glossy) in any and shape, confirming to IS-15658-2006 of 80mm thickness, M-40 grade in path, hard standing, etc. laid over and including 50 mm thick screed or bedding layer of sand complete, all as specified and as directed.

Material and labour for plain cement concrete 1:2:4 type B1 using 20mm graded stone aggrgate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, kneelers, apex stones, bed plates,coping, kerb, water trough and the like including weathering slightly rounded or champfered angles and throating as directed including use and waste of formwork finishing exposed concrete surface fair and even complete all as specified and directed.

Material and labour for cleaning and removing all sewage from manholes, septic tanks of any capacity and making manholes, septic tanks fully serviceable complete all as specified and directed.

Material and labour for cleaning choked sewage pipe lines of any dia and description and making sewage pipe lines fully serviceable complete all as specified and directed.

Material and Labour for rough cast plaster on brick work or concrete surfaces consisting offine gravel, cement and sand in the ratio of 1:1:1 over 15mm thick under coat in cement mortar 1:3 as specified in clause No. 14.22 of SSR Part-I, complete all as specified and as directed.

Material and labour for machine cut kota stone slab 18-22 mm thick (of size not less than (55 cm x 55 cm) laid in flooring and jointed and pointed with grey cement slurry mixed with pigment to match shade of the slab including cutting waste, rubbing and polishing (Granite finish) over and including cement screed bed 20mm thick in cement mortar (1:4) base complete, all as specified and as directed .

Material and labour for machine cut kota stone slab 16-18 mm thick laid on vertical surface and jointed & pointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) but as in skirting over and including 10mm thick plaster in cement mortar (1:3) on brick work or concrete surfaces complete, all as specified and as directed.

Supply and fixing of chromium plated nipple with flange as in bib taps, stop cocks, angle cocks, etc. complete all as specified and directed.

Supplying and fixing of white glazed ceramic tiles, of size 150x75x5/6mm thick, fixed on vertical surfaces of walls over and including 10mm thick rough finished plaster in cement mortar (1:4), set and jointed in neat cement slurry and pointed in coloured cement to match the tile including painting Building No/Quarter No. with black marking paint complete all as specified and as directed.

Supply and fixing for (in repair) 2nd class hard wood fillets, clean swan, bull nosed, chamfered or rounded on one face, sectional area not exceeding 3 Sq. cm, fixed with nails or brads including two coat of painting over a coat of pink primer after preparation of new fillets surface, complete all as specified.

SCHEDULE A PART II (INTERNAL ELECTRIFICATION)

Taking down carefully any type of point wiring (light, fan, socket or power) complete with fittings such as switches, ceiling roses, pendants, regulators, sockets, tube light fittings with all accessories etc., and/or drawing out from existing conduit/batten and removal of materials from site and making good the disturbed surfaces of wall, floors, ceiling etc to match with the existing surfaces with matching OBD/White wash/Distemper complete all as specified and as directed.

Material and labour for concealed point wiring using approved colour coding as per IS, with multi stranded copper conductor 1.5 sqmm (Nominal area) single core flame HFFR/ZHFR(Zero Halogen Fire Retardant),PVC insulated and unsheathed stranded cable 1100 volts grade ISI-694 marked TEC and FIA approved in and including non metallic, heavy duty PVC concealed conduit not less than 20mm dia and its fittings including all tees, bell mouth pieces and fixing accessories such as couplers, saddlers, pipe hooks etc, PVC junction boxes ISI marked with GI flush box , inner and outer plate as required for housing modular switch and socket as per module including HFFR/ZHFR(Zero Halogen Fire Retardant),,PVC insulated and unsheathed, copper conductor 1:5 Sqmm nominal cross sectional area wire as earth continuity conductor upto common earth and connecting to common earth dolly for one light/fan point controlled by one switch. complete, all as specified and directed. Note :- Modular Switch, socket and fan regulators to be measured and paid separately) . PVC Conduit confirming to IS 9537 part I & III Note (All chases will be cut by chase cutter only)

Description all as per Srl item No.3.02 here in before but for socket outlet point 5 Amp on Independent board complete, all as specified and directed.

Description all as per Srl item No.3.02 here in before but for socket outlet point 5 Amp on same board complete, all as specified and directed.

All as per the description of Serial Item No 3.02 above, but with 4.00 Sq mm un-sheathed multistranded cable for one socket outlet 15 Amps independent including continuous copper earth wire, PVC insulated of 4.00 Sq mm size, complete, all as specified and directed.

Supply and fixing of switch, modular, one way, 6 Amps, one module, 230 volt, ISI marked complete all as specified and as directed. Make: Legrand (Arteor), Schenider (Zencelo), Hager (Insista)

Supply and fixing of switch, modular, one way, 16 Amps, one module, 230 volt, ISI marked complete all as specified and as directed. Make: Legrand (Arteor), Schenider (Zencelo), Hager (Insista)

Supply and fixing of socket, modular, 2/3 pin, 5 Amps, 2 module, ISI marked complete all as specified and as directed. Make: Legrand (Arteor), Schenider (Zencelo), Hager (Insista)

Supply and fixing of socket, modular, 2/3 pin, 6/16 Amps, combined, 2 module, ISI marked complete all as specified and as directed. Make: Legrand (Arteor), Schenider (Zencelo), Hager (Insista)

Supply and fixing of electronic fan regulator, modular, 120 watt , 2 module, ISI marked, suitable for ceiling fan, any type/make/sweep complete all as specified and as directed. Make: Legrand (Arteor), Schenider (Zencelo), Hager (Insista)

Supply and fixing of bell push, modular, one way, 6 Amps, one module, 230 volts, ISI Marked complete all as specified and as directed. Make: Legrand (Arteor), Schenider (Zencelo), Hager (Insista)

Supply and fixing of calling bell, ding-dong type, 230 Volts, ISI Marked complete all as specified and as directed.

Supply and fixing of ceiling rose surface bakelite 65x50mm, two to three terminals complete all as specified and as directed. Make: SSK, Anchor, Kinjal, Fine

Supply and fixing lamp holder, PVC/polycarbonate type with back plate suitable for angular batten fittings with one block of size 75mm x 75mm for mounting fitting including LED bulb, 09 watt retrofit type, ISI marked ,complete, all as specified and directed.

Supply and fixing of batten tube light channel suitable for LED tube, single wall/ceiling mounted with all accessories internally prewired and including LED tube light 18 watt lamp, with aluminium heat shrink, high frequency, power factor of 0.90, suitable for connecting up with twin core copper conductor cable of size 23/0.0076 from ceiling rose to connector of the light fitting complete all as specified and as directed. Make- Havells Cat No.(Fitting) REGAL BATEN T8 4TPO 1x22WSSBSWH (for Tube) - CRYSTAL 1213 T8DSTL 20WLED865SGLASS or WIPRO Cat Part No (for fitting) - W10921208 (for Tube) - LC13181 or PHILIPS Cat Part No (for fitting) - TMC501 1xT-LED 22W P3241 (for Tube) - 20W865 T8 INDI -2100Lm for Tube.

Supply and fixing of MCB, single pole, 240 volts, 50Hz, breaking capacity 10KA, 'B' curve, 6 to 32 Amps, ISI marked complete all as specified and as directed. Note: Thimble/lugs of ratings of MCB should be used with wire for fixing in the MCB. Make: Schenider/Hager/Legrand

Supply and fixing of RCBO, 40 Amps, 230 volts, conforming to IS-12640-2 with IP 20 protection, ISI marked, with earthfault indicator, short circuit and sensitivity, 100mA (HI immunity) complete all as specified and directed. Make- Legrand/Schenider/Hager

Supply and fixing of over voltage relay, prevention range (170V-276 V) , between phase/neutral 230 V, SPN, 1 module, complete all as specified and as directed by the Engineer-in-Charge. Make Hager Cat Part No-MZ209 or equivalent model in Legrand/Schenider.

Supply , insatallation, testing of SPN distibution board 08 way,double door , IP 43 , as per IS 8623 including 200 amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, PAN assembly for easy installation and also incoming and outgoing connections with suitable size of lugs/thimbles, concealed on the wall surface including taking down the existing DB's any type and description and making good the disturbed portion with adjoining surfaces to match with existing finish, complete, all as specified and as directed. Make: Schenider/Hager/Legrand

Supply and fixing in repair of LED security light fittings of capacity 40 watts, made up of cast aluminium body housing with black epoxy powder coating with cover heat resistant glass safety input voltage range 170 to 270 volts, 0.95 power factor and other connected accessories including bracket made up of 0.90m long GI pipe, 32mm dia medium grade, bent to required length and fixed to wall with two clamps made of 40x6 mm mild steel flat iron 15cm long, 4 Nos 8mm dia bolts with nuts complete with all accessories, internally pre wired and connecting with 3 core copper conductor flexible cable from terminal box to the ceiling rose or connector of the light point including disconnecting and taking down of existing light fitting and removing from site complete all as specified and as directed. Make- Havells Cat Part No LHETAXU7PN6J045, Wipro Cat Part No CRLA11008HP57-05, Philips Cat Part No BRP409LED040CWHOMRFSIPSURR.

Material and labour for taking down of ceiling fan and preparation of old painted surface of ceiling fan of any make and sweep and spray painting with two coats of white duco paint, writing MES No with black colour permanent marker including filling cavities with filler after cleaning dust, etc. and refing in same or other location including provision of three core flexible cable 23/ 0.0076 size from ceiling rose to connector of fan complete all as specified and directed. , complete all as specified and as directed.

Material and labour for sub main wiring with two single core ZHFR (Zero Halogen fire Retardant),, ISI Marked, PVC insulated, unsheathed, copper conductor cable, 6 sqmm, housing in and including capping and casing of adequate size with accessories on surface of wall or ceiling with one additional single core PVC insulated, stranded copper conductor, ZHFR (Zero Halogen fire Retardant),, ISI Marked, 6 sqmm, green colour for earth continuity conductor including taking down of old unserviceable sub main wiring, any size and any type complete all as specified and directed. Note- Three runs of 6 sqmm cable and one run of casing and capping conduit shall be measured as 1 unit. Make- Havells/Polycab/Finolex

Taking out old earthing complete and taking out old unserviceable earthing material and provision of new earthing complete with galvanised earth plate electrode 600mm x 600mmx 6mm thick surrounded by charcoal and salt, buried directly in ground vertically in a pit of depth not less than 2.25m below ground level with top edge of the earth plate not less than 1.5m below normal ground level, connected to 4.00 mm wire earth lead by means of bolts, nuts, checks nut and washers made out of galvanized iron or steel, earth wire protected by galvanized steel pipe 15mm dia (light grade) and connected to main switch or main control board all as shown in electrical plate No.3 of SSR Part-I & including necessary excavation and earth work. The rate also include charcoal & salt in alternate layers, 20mm dia GI pipe (light grade) for watering, protection pipe, funnel, wire mesh, RCC cover etc. complete, all as specified or indicated including testing on completion. Note : The rates for earth work, GI protection pipe, funnel, wire wesh, RCC cover, etc shall be deemed to be including in quoted rates. RCC cover shall be 50mm thick in 1:2:4 type B-1 using 8mm bars @10cm c/c both way.

Supply and fixing distribution board for Load line TPN, 4 ways, double door, 415 volts, with and including 200 amps rated bus bar, vertical type, IP 43 protection powder coated, suitable for MCCB as in incomer including provn of MCCB 125 Amp, FP, 16KA and MCB's as out going with suitable size of MS cabinet 2mm thick and making all type of connections with suitable size of gland for incomer cable complete , concealed on the wall surface, making good the disturbed portion with adjoining surfaces to match with existing finish and taking down the existing DB's and MCB's any type complete, all as specified and directed.

Supply and laying of cable, XLPE, insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty), 1100 volts grade, with stranded aluminium conductor of size 3.5 core, 25Sqmm and laying in trenches complete all as specified and as directed. Make of cable- Gloster/Finolex/Havells

Excavating in trenches, not exceeding 1.50 metre wide and not exceeding 1.50m in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exceeding 10 sq.m on plan and not exceeding 1.50m in depth and getting out in soft/loose soil complete, all as specified and as directed .

Returning filling in, in soil, including spreading leveling watering and well ramming in layers not exceeding 25 cm each complete all as specified and as directed.

Removing excavated materials to a distance not exc 50 m and depositing where directed at level n exc 1.5 above the starting points complete, all as specified and as directed.

Material and labour for fine and dry sand, cushioning for underground cable, by providing a layers of sand 8cm deep before laying and 15cm deep after laying the cable including stretching the cable and punning sand cushioning complete all as specified and as directed. Note - Punned thickness of sand layer shall only be measured and paid to contractor.

Supply and laying un-reinforced, precast concrete cable cover, class LV type 1, Flat, with peak, size 250 mm x150 mm x40 mm complete all as specified and as directed.

Supplying and fixing light grade GI tubing of size 40 mm dia for cable protection and fixed with clamp to pole and wall with nut bolt complete, all as specified and as directed.

Note:- Amount of credit of Rs. 68,020.00 for retrieved materials is mentioned in Schedule of Credit Page Nos.106R & 107R of tender documents in pdf form which will be deducted offline while acceptance of tender.

V K Constructive Builders

M/s Vridhi Construction Co.

bhagwandasswazirchand

Bairagi Builders

s.v.builders