Design, Engineering, Procurement, Construction of Nagar Nigam Building Renovation with Third Floor Refurbishment including three year Defect Liability Period at Satna, Madhya Pradesh

Amount

LT Switchboards/ Feeder Panels:

Main Lighting Distribution Board (Outdoor) Supplying, fixing, testing & commissioning of outdoor wall/ floor mounted compartmentalized type LT Panel suitable for 415V, 3 phase, 50 Hz, 4 wire system complete with all accessories and miscellaneous equipment as per specification. The panel shall be fabricated out of 2/ 2.5 mm thick GI sheet steel, powder coated paint & provided with required gasket for dust / vermin proof with degree of protection IP55 of suitable size double door & locking arrangement with provision of following : Incomer MCCB, 4 pole, 63-80Amp -1 no. 415V, 50 Hz TPN Busbar - 1 set. 50-63 A TPN MCCB for three phase consumers- 4 nos. Digital Energy Meter – 1no. RYB Phase indication LED lamps – 3 nos. Holder with switch & 9watt LED lamp for panel illumination Earthing terminal – 2 nos. Wiring & insulation sheet Cable glands suitable for 3.5C x 50 mm² PVC armoured cable Concrete foundation (for plinth mounting) Rating plate/ Name plate Danger Board Sundries

P & F of Integral, SMD 2x2 LED, IP 20, 33W LED Recess mounted fixture with System efficacy of more than 93lm/W and system lumen output 3069lm.. Luminaire with versatile LED with white powder coated rough aluminium extruded housing. Luminaire shall have polycarbonate diffuser for Uniform illumination and wider light distribution. LM 80-08 compliant LEDs from reputed makes such as Nichia / Cree / Bridgelux / Lumileds should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Luminaire shall use SMD type LED. The LED shall be compliant with LM80-08 standard with L70 life of 50000 Hrs tested at maximum current (Complete LM 80 test report for LED should be submitted for 10000 hrs of testing). The LEDs used should be with CCT of 5700 K and CRI of Minimum 80. LED Driver shall be Multistage, Isolated type, APFC, Constant Current topology driver with proper heat sink for heat dissipation suitable to operate in input voltage range of 150V to 270V (nominal rated voltage – 240V) with 2KV internal surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire. Complying to SELV < 60V DC standards. Compliance to Indian Standards of IS10322 Part 5 / Sect 1:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012. Wipro Model No. LM29-451-XXX-57-XX (False ceiling) , LM29-451-XXX-57RCC (Suspended from RCC ceiling) and LM29-451-XXX-57GRD (Suspended from grid ceiling)/ Equivalent Make & Model.

LED Downlighter - MOLLIS X: P & F of 9W, High efficient deep inset recess mounted LED round downlighter with white powder coated, pressure die cast aluminium housing. High transmittivity PS diffuser provides soft light. CRI>80, IP40, Ambient temp-0 to 45DegC, CCT - 4000/5700K, 50,000 hrs @ L70 life.Driver efficiency>85%, THD<10%, Powerfactor>0.9, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 90-265V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 900 lm. (100 lm/W) - Cutout Dia-ø115mm Similar to Wipro LD06X-111-XXX-40-XX/ equivalent Make & Model.

LED Downlighter- FOKUS LED Downlight: P & F of 18W, High efficient deep recess mounted COB LED downlighter with extruded aluminium housing with UGR<19. High efficiency PC frosted reflector optics for effictive thernmal management using aluminium casting. CRI>80, CCT - 5700K, 50,000 hrs @ L70 life.IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Cutout Dia-ø100mm. Luminaire lumen ≥ 1800 lm. (100 lm/W) , Similar to Wipro LD31-221-060-40-SR/ equivalent make & model

LED Batten- TrimLED Neo: P & F of 40W High efficient LED batten surface/wall mounted Specially designed extruded Aluminium housing with PC diffuser. In-built electronic driver duly wired up to terminal block.IP20, CRI >80, Temperature range-0 to 50DegC, Driver efficiency>90%, Power factor>0.95, CCT - 6500K, THD<10%, Surge protection 2kV, 50000 burning hours as per L70 Criteria, Multistage Isolated Constant Current operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 4000 lumens (100 lm/W) similar to Wipro LL24-541-XXX-57-XX/ equivalent make & model.

LED Flood Light P & F of IP-66 protected high power LED flood light system with extruded aluminium housing, toughened glass diffuser with suitable lenses on LED to achieve various beam angles, 240 volt, 50Hz, of high power LED lamps supplied with pre wired cable of 1 mtr. Integrated driver shall be high efficiency having efficiency more than 85% and in compliance to IEC standards. System life of 50000 burning hours with 70% of initial lumen be maintained. Light output in red , green, blue, cool white or warm white colour as per engineers choice. Fixtures shall be CE compliance. High power LED flood light 150 watt (Smart)

Post Top Lantern: P & F of 60W, High efficient LED with aluminium housing in Pure Polyster UV resistant powder coated black finish with PC diffuser.CRI>70, IP65, Ambient temp-0 to 45DegC, Driver efficiency>85%, CCT - 6500K, THD<20%, Powerfactor>0.95, Surge protection-4 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 180-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 5400 lumens (90 lm/W). Similat to Wipro LP05-711-XXX-57-XX/ equivalent make & model.

Decorative Poles (PU Painted Conical Pole) Providing & erecting hot dipped galvanized and PU painted Conical Poles in single section made from 3 mm thick HT plate having nipple on top to mount the post top lantern fitting, lockable weather proof flush door junction box (with Bakellite sheet of 275x75x4mm with 4Nos stud Terminals and one no of 6 Amp SP MCB and Connectors for proper wiring of LED Fittings) complete with foundation bolts of suitable size - 4 nos. 'J' type (EN8 grade), erected in an approved manner on provided foundation. 4 mtrs. Height, 118 x 75 mm A/F, 200 x 200 x 12mm base plate, 4 nos. X M16 x 600 mm long bolt

RCC Foundation- 4m Decorative Pole Designing & casting with M-20 reinforcement cement concrete foundation of size 45 x 45 x 100 cms. deep in below ground level with plinth of 45 cms x 45 cms (or 45 cms dia) x 20 cms above ground level suitable for Conical Poles considering the safe soil bearing capacity at site as 10 T/sqm at 2 mtrs. depth including excavation, foundation nut bolts with necessary curing and finishing in an approved manner.

LED Bollard Providing & fixing of floor mounted bollard 11W LED, 800mm approx height Light distribution for uniform lighting all around with extruded milky white PC Diffuser. colour temperature 3000K/ 6500K. Housing should be made of aluminium extrusion with pure polyster powder coated for rust protection. Product should have IP 65 Protection. System lumen output should be 550 - 570 Lm. Life of LED should be L70@50000 Hrs and LM80 report should comply the same. LED Driver Should be SELV and have I/P voltage Range 180V-270V, Surge - 2KV, O/p Short Ckt, O/p Open Ckt. Product Should be BIS Approved. Simillar to Wipro cat ref - LB14-131-XXX-65-08 or equivalent make & model. Reports Req. - LM80, LM79/ Photobiological Safety Report Complete erected in an approved manner on cement concrete foundation/ suitable base structure including mounting hardware etc.

Cable Pull Pits/ Chambers: Construction of brick masonry pulling chamber of required size and depth up to 0.6 meter with 230 mm thick masonry in cement mortar proportion 1:6, 12 mm thick cement plaster in CM 1:4 in both side, 150 mm thick PCC M-10 at bottom, 100 mm thick R.C.C M-20 coping at top of wall, 100 mm thick precast concrete cover in RCC M-20. including excavation and back filling & clearing the site by removing debris & Shifting of the debris & making site good as per the Instruction of the Engineer In charge complete in all respect. 450 mm x 450 mm inside clear size

Earthing for Lighting Pole Providing MS Rod Earth Electrode (20 mm dia x 1.5 m long) with required length of 6SWG GI wire for individual lighting pole earthing.

Proposed Electrcal ( Air Conditioning ) Works

2.0 Ton, 5 Star Cassette Inverter Split Ac

Voltage Stabilizer For 2 Ton Ac

1.5 Ton, 5 Star Inverter Split Ac

Voltage Stabilizer For 1.5 Ton Ac

1.0 Ton, 5 Star Inverter Split Ac

Voltage Stabilizer For 1 Ton Ac

Stainless Steel Type Passenger Lifts, Max Persons/Capacity: 6

Fire Water Pumping System

Supply, Installation, testing and commissioning (SITC) of Electric motor driven Horizontal Centrifugal End Suction Type Main Pump having flow 137m3/hr & 70 MWC head along with all accessories and recommended spares required for the pump set.

Control Panel for Electric Driven Fire Pumps

Supply, Installation, testing and commissioning (SITC) of Diesel Engine driven Horizontal Centrifugal End SuctionType Standby Pump having flow 137 m3/hr & 70 MWC head along with all accessories and recommended spares required for the pump set. Including fuel tank (fabricated from 3mm MS sheet, painted with two coats of synthetic enamel paint over a coat of primer) of capacity adequate to sustain pump operation for 8 hours continuous working. The tank shall be fitted with Magnetic oil level indicator, MH with cover, drain valve, air vent including structural supports (painted with approved shade), 2 Nos. x 12 volt battery WITH CHARGER, heat exchanger with necessary piping connections & fittings, flexible coupling, coupling guard & exhaust pipe connection complete as required. Cost shall be inclusive of providing & fixing of fuel tank of required capacity etc. all

Control Panel for Diesel Engine Pump(Diesel Engine Control Panel with SMPS type Charger)

Supply, lnstallation, testing and Commissioning of MS Class ‘C’ 150 mm Dia Diesel engine exhaust pipe with necessary thermal insulation with 50 mm. thick glass wool with 1.0 mm. thick aluminium sheet cladding, 25mm SS mesh (including all fittings, clamps, galvanized steel support) of suitable dia for the engine.

Supply, Installation, testing and commissioning (SITC) of Electric motor driven vertical inline Type Jockey Pump having flow 10.8 m3/hr & 70 MWC head along with all accessories and recommended spares required for the pump set.

Control Panel for Jockey Pumps

Providing, laying, testing & commissioning of 'C' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

Supply, lnstallation, testing and Commissioning of UL Listed/FM Approved Brass Ball valve With threaded end,Minimum working pressure-200 PSI including necessary nuts, bolts, teflon & gaskets etc complete as per specification as specified inclusive of all accessories required for satisfactory installation.

Providing & fixing bronze Globe valve, PN16, conforming to IS 778 screwed in bonnet, Bronze body, disc & stem union flanges, washer nuts & bolts, rising stem, connectors, adapters etc. complete, high quality PTFE gland packing with necessary unions, complete .

Providing & fixing of heavy duty double flanged flexicon rubber expansion joint (suitable for system test pressure) of standard length as per manufacturers specs including rubber gaskets, flanges, nuts, bolts and washers complete as required.

65 mm dia

150 mm dia

Supply, Installation, testing and fixing of dial type (100 mm) pressure gauge with isolation globle valve suitable with ‘U’ tube for working pressure of 12 Kg/cm2 having calibration of 0-16 Kg/cm2. Cost shall be inclusive of providing any short pieces, nipples, elbows etc as required.

Supply, Installation, testing and commissioning (SITC) of Pressure switches. The Pressure Switch shall be diaphragm type. The housing shall be die cast aluminum, with SS 316 movement, pressure element and socket. The Switch shall be suitable for consistent and repeated operations without change in values. It shall be provided with IP: 65 enclosures. Range of pressure switch shall be 0-16 kg/cm2 and shall be provided with isolation ball valve.

Supply, lnstallation, testing and Commissioning of FM approved Ventruri Flow Test Meter with waste cone on Test Line to measure 150% of pump flow and suitable for mounting on 150 mm dia pipe as per specifications

Supplying and installing fire water draw off connection 100mm dia G.I. "C" class pipe, from Water Tank to outside approachable location. Including the flanges to be provided for the easy maintenance with Isolation Sluice valve for system, etc as complete to operate

Supply, lnstallation, testing and Commissioning of CI flanged end Foot valve as per IS 4038/1979 with strainer with necessary rubber insertion/bolts and nuts etc complete.- 100mm dia

Supply, Installation and erection of Structural Steel for supports including anchor fastners, ISMB Channels, angles, painting of structures.

Supply, Installation, testing and commissioning (SITC) of Electric motor driven Horizontal Centrifugal Monoblock Type Booster Pump having flow 450 LPM & 35 WMC head along with all accessories required for the pump set along with control panel.

Providing, laying, testing & commissioning of 'C' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100 NB

Supply, Installation, testing and fixing of dial type (100 mm) pressure gauge with isolation globle valve suitable with ‘U’ tube for working pressure of 12 Kg/cm2 having calibration of 0-16 Kg/cm2. Cost shall be inclusive of providing any short pieces, nipples, elbows etc as required.

Supply, Installation, testing and commissioning (SITC) of Pressure switches. The Pressure Switch shall be diaphragm type. The housing shall be die cast aluminum, with SS 316 movement, pressure element and socket. The Switch shall be suitable for consistent and repeated operations without change in values. It shall be provided with IP: 65 enclosures. Range of pressure switch shall be 0-16 kg/cm2 and shall be provided with isolation ball valve.

Providing, laying, testing & commissioning of 'C' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

Supplying and fixing standard Fireman Axe with heavy duty insulated rubber handle as per IS: 926 with clamps as per specifications

Supply & installation Auto Air vent for risers, suitable for pressure not less than 15 Kg/Sq.cm.- 15NB

Providing & fixing bronze Globe valve, PN16, conforming to IS 778 screwed in bonnet, Bronze body, disc & stem union flanges, washer nuts & bolts, rising stem, connectors, adapters etc. complete, high quality PTFE gland packing with necessary unions, complete .- 15 NB

Supply and Installation of portable fire extinguisher system as per IS 2190 and IS 15683.

water stored pressure type 9 liters

Mechanical Foam Type Fire Extinguisher 9 Lit capacity.

Wet Chemical Fire Extinguisher 9 Lit capacity.

CCTV CAMERA AND STORAGE

SITC of Indoor Application IP Dome camera with 1/3" CCD/CMOS, Progressive Scan, HD720P Min 2.0 MP Resolution, Dual H.264 streaming, 25 FPS, 2.8mm-9mm varifocal auto iris lens, 0.01 lux,Tamper detection,Wide dynamic Range, 3D Noise reduction, PoE & standard 12VDC/24VAC power input, Indoor surface mount enclosure, Mounted on True Ceiling / False ceiling as per site requirement (including required accessories), UL Listed as per detailed specifications. Camera Shall be ONVIF compliant.

SITC Outdoor Application IP Fixed Box camera with 1/3" CCD/CMOS, Progressive Scan, Day/Night, HD720P Min 2.0 MP , Dual H.264 streaming, 25 FPS, 2.8mm-9mm varifocal auto iris IR corrected megapixel lens, 0.05 lux Day/Night, Tamper detection, Wide dynamic Range, 3D Noise reduction, PoE & standard 12VDC/24VAC power input, IP66 rated vandal resistant enclosure with built in Heater and Blower, UL Listed as per detailed specifications. Camera Shall be ONVIF compliant.

SITC Redundant Mode, Solid State Power Supply Module for up to 16 cameras, Wall mount, with inline filters & Stabilisation for the the PTZ Cameras. Power input shall be 230 VAC from UPS. Output to suit the Camera Requirements, as pre-approved by the Consultants.

SITC GI Pole, 80mm dia, 5m high with 2 coats of reoxide primer and 3 coats of external colour as per Architects recommendation, complete with mouting accessoires as required for the pole as well as the cameras, suitable to mount the outdoor cameras to the directions of the consultant.

SITC Servers and Networking (NAS) Hardware : - 19" rack mount Server Hardware (NAS) for Directory, Video Processing & Recording; Onboard CPU: Core i5 and above Onboard Memory: 2 x 4 GB DDR3 SDRAM HD Drive: 15 TB IDE/SATA/SCS @7200rpm with RAID 5 Host Interface: Dual Gigabit Ethernet (250 mbps support) Network Transport Protocols: TCP/IP, IPX (Internet work Packet Exchange) Network File Protocols: CIFS (Common Internet File System), NFS (Network File System), HTTP/ HTTPS, FTP, NTP (Network Time Protocol), SNMP (Simple Network Management Protocol), SMTP (Simple Mail Transport Protocol), DHCP (Dynamic Host Configuration Protocol) and DNS (Domain Name System/Service). Secured Administration Access: Administrator can use Secure Sockets Layer to Connect the NVR and Configure NVR to Respond Only to SSL for Configuration. Drive Status/ Space Monitoring: Supported Network Client Support: Microsoft Windows/ Linux Power supply: AC 230 V @ 50Hz (Dual Redundant Power Supply) Bidders to Provide Storage Calculations to substantiate the Storage Requirements in the Tender. If a Bidder would require larger storage, the same to be mentioned and included in this line item. Embedded Gigabit network cards with fault tolerent configuration, Complete with Windows 2008 or higher Server OS. Capable of Redundant power supply etc. as per detailed specifications.

SITC of Client PC Hardware with a Minimum speicification of Processor: Intel Dual Core i5 Processor 4.5 Ghz with EM 64 Technology Memory: 8 GB (2 x 4 GB) dual channel DDR4 memory, Upto 16 GB Max. memory expandable through four DIMM slots Cache (External) 2 x 2 MB L2 Cache ROM: 512 MB Flash ROM, Can be upgraded from a diskette Expansion Bus: 2 nos. PCI Express (x1), 4nos 32 bit PCI slots, 33 MHz PCI 2.2 slots, 1-graphics slot Graphic Accelerator: N-vidia Quadro FX 4400(DVI/VGA)with 512 MB Memory with dual monitor capable graphics card Hard Disk: 1 TB 7.2K rpm SATA hard disk Power Supply: 375 W switchable/50 Hz with dual power supply provisions Keyboard: 104 keys window 98 keyboard, USB Compatible Operating System: Supports Windows 10, OS/2 Warp, Windows Server 2016, DOS 6.22 Software: Windows 10 Professional and MS Office 2019, Microsoft Internet Explorer Power Management: EPA compliant Desktop Manager: Based on SNMP protocol Antivirus Software: PC-Cilin or equivalent pre-loaded Diagnostic Software: PAQ 95 or equivalent pre-loaded Network Broad cam 10/100/1000 Mbps Ethernet adapter Network Interface Card with wake on LAN support Interfaces: 1 parallel, 8 USB 2.0, 1 serial, 1 HDMI, 2 Ultra ATA/100,2 optional IEEE1394, 1 PS/2 Keyboard, 1 PS/2 Mouse, 1 video, 1 Microphone jack, 1 Line-in jack, 1 RJ-45, 1 Headphone jack & 1 line-out jack (analog/SPDIF digital Audio Card: Integrated AC 97/16 bit Stereo full-duplex and integrated speaker Mouse: Cordless Mouse Monitor Monitors shall be with a minimum 55-inch OLED flat panel display. DVD Writer: DVD-RW Drive with speakers With different content possiblity on each of the monitor i.e Multiplexed, Alarm, Maps, sequence or any combination. Also Support Drag-n-drop of images by using connected mouse device.

SITC of Smart Television 55" OLED, 3840x2160- UHD, Smart Android, Static contract Ratio-1100:1, typical brightness-400-500, with Screen mirroring, mount type-both table and wall mount, with built in speakers 20W x 2, number of HDMI ports-3 , number of USB ports-2, number ofethernet Ports-1, builtin wifi, wifi direct, composite input, component input, RFP input. BIS registered as per CRS of Meity, Energy start rating in line with GOI notification number SO 1896(E) and S O 1897(E). With min. 1 years OEM on site warranty. HD monitor for above client workstation

SITC of Network Video Management Software expandable up to 100 cameras in Single Directory; Virtual Matrix capablity; Maps and alarm management etc. Open Protocol ONVIF Compliant system architecture complete with all necessary licenses etc, minimum as per below : Connection License for up to 100 Cameras shall be included in this. Unlimited Storage License for Site, Minimum 2 Admin and 5 Concurrect User Licences

Video Analytics Processing Software & Hardware :- TO Support Minimum 10 cameras, programmed with any 1 or more, of the following of the following Video Analytics features : a) Object left behind, b) Directional Motion (Adaptive Motion), c) Object Removal d) Camera Sabotage e) Loitering e) Crowd Detection f) Trip Wire g) Object Counting h) Vibration Removal (The System shall allow implementation of Video Analyitcs on any user defined cameras during comissioning). Independent servers, if required to be used for video analytics shall be included in this item as required.

SITC of Software for third party systems integration with IP CCTV System for Access control system This shall allow for interface development by access control manufacturer, for the Purpose of Database level integration with IBMS / Access Control.

Independent LAN for IP CCTV Camera System :- Supply & Laying of following cables/cable trays/cable trunk/conduits as per technical specification.

16 port layer 2 switch with 10/100/1000 POE Managed Switches with IP multicast snooping and data-driven IGMP support and with two 1000baseT single mode FO uplink ports (with ready Fiber Optic module on Board) and all related termination accessories (Like Pigtails/ LIUs/ Convertors/ Splicing equipment, etc.) as per site specific System requirement and 2 U rack.

Modular 24 port Layer 3 managed switch with required number of 10/100/1000 copper & Fiber ports ; required number of 10/100 POE ports etc. as per project requirement and all related termination accessories (Like Pigtails/LIUs/Convertors/Splicing equipment ,Patch panel,l Etc.)

FRLS, Cat-6 cable (Armoured), laid on Surface with GI Saddle- Spacers ,as per site requirements, with required terminations as required with Cable tie`s & Tags, Outer sheath Blue in color

Power Cable : 4 Core x 1.00 Sq.mm, FRLS, Armoured, PVC insulated ,PVC Sheathed Cable laid on Surface , as per site requirements with GI saddles & spacers with termination lugs, cable tags etc, Outer sheath Blue in color

Single mode 4 core Fibre optic cable with FRLS outer Sheath , with required terminations, Junction Box, SC/LC Connectors, Cable tie's & Tags, Outer sheath Blue in color

42 U Rack for all above Equipments like CCTV Client PC's in the Control Room with Tamper Switch to be monitored on IBMS as per consultant guidelines during the execution of project.

25 mm PVC Conduits with Saddle & Spacers, every 300 mm of run, all fittings and accessories, and with Flexible PVC Conduits to contain Communication / Other Cables as per the directive of the consultant Vendor check if can be supply conduits in Blue Color

100mm x 50mm x 2 mm GI cable trunking (powder coated) complete with supports, all fittings and mounting accessories, etc complete to installation requirements.

3 Meter copper patch cord cable fitted with RJ45 connectors at both ends, with IO Module at each Camera Points as per site requirement.

EPABX - System

Supply and installation of EPABX System with Extension 48 analog trunk including all Console Directed as per Engineer-In-Charge

Auditorium Chair (Compact Type) Type of seat: seat with auto tip up mechanism with push back feature. Seat rest assembly:12mm ±1mm thick flat plywood moulded with polyurethane foam and upholstered with 3layer foam laminated. Seat under structure:MS black powder coated understructure with integrated auto tip-up mechanism which folds the seat when not in use. Fixing of understructure to ground: By anchors with washer and nut. seat width ±10mm:480 millimeter. seat depth ±10mm:440mm. Seat thickness(including cushion)±10mm: 110mm. PU foam moulded with density±2Kg/CuM:50Kg/CuM. Upholstery fabric:Fire retardant treated fabric. Shade of Upholstery fabrics:Red. Mode of Supply of auditorium chair:Knocked Down To Be Assembled At Consignee Site By The Seller. Type of chair: Floor mounted. Type of backrest: push back. Backrest assembly made up: Of PU foam moulded with MS tubular frame insert and upholstered with fabric and back cover. Backrest width ±10mm: 450mm. Backrest height ±10mm: 750mm.. Backrest thickness ±10mm: 110 mm. PU foam moulded with density ±2mm: 50Kg/Cum. Upholstery fabrics: 3-Layer Foam Laminated Fabric. Shade of Upholstery fabric: Red. Type of armrest One side(common for two chairs). Armrest made up of: Integral polyurethane foam with 65mm±10mm 'A' hardness and reinforced with MS insert fixed with leg frame. Armrest cladding: Metal structure. PU foam moulded with density ±2mm for Armrest: 50Kg/CuM. Armrest width ±10mm: 80mm. Side panel/Aisle panel (chair rests on the ground on two side panels frames): Made up of 2mm thick CR steel.each side panel is clad with two fabric upholstered particle board of 9mm thick. Leg frame assembly fabricated: From MS tube 60mmX40mmX2mm thick welded with grouting member. Writing pad: Without. Type of writing pad: N.A. Number of bottom plates: 2 Nos foundation plate of 120mm(W)X170mm(L)X5mm(T) HR steel. Rocking Spring: Rocking coil spring steel conforming to IS:4454/Latest grade II tested for 500000 cycle. Arms to arms inner width ±10mm: 550 mm. Seat to floor height ±10mm: 400 millimeter. Backrest to floor height ±10mm: 1050 millimeter. Arms to floor height: 675 mm. All steel components should be: Epoxy polyester powder coated(DFT 40-60 microns). Warrantee period in number of years: 3-year.

Auditorium Chair (Premium) Type of seat:seat with auto tip up mechanism with push back feature Seat rest assembly:12mm ±1mm thick flat plywood moulded with polyurethane foam and upholstered with 3-layer foam laminated fabric and injection moulded cover Seat under structure: MS black powder coated understructure with integrated auto tip-up mechanism which folds the seat when not in use seat width ±10mm: 600 millimeter seat depth ±10mm: 440mm Seat thickness(including cushion)±10mm: 130mm PU foam moulded with density±2Kg/CuM: 50Kg/CuM Mode of Supply of auditorium chair:Knocked Down To Be Assembled At Consignee Site By The Seller Type of chair: Riser mounted Type of backrest:push back Backrest assembly made up:Of PU foam moulded with MS tubular frame insert and upholstered with fabric and back cover Backrest width ±10mm: 700mm Backrest height ±10mm: 700mm Backrest thickness ±10mm: 150 mm PU foam moulded with density ±2mm: 50Kg/Cum Type of armrest: Both sides Armrest made up of: Integral PU foam-50mm Armrest cladding; N.A PU foam moulded with density ±2mm for Armrest: 50Kg/CuM Armrest width ±10mm: 80mm Side panel/Aisle panel (chair rests on the ground on two side panels frames): Wood Covered With Fabric And Fused With Foam Leg frame assembly fabricated: From MS tube 60mmX40mmX2mm thick welded with grouting member Writing pad: Without Number of bottom plates: 4 Nos Foundation Plate Of 120mm(W)X170mm(L)X5mm(T) HR Steel Arms to arms inner width ±10mm: 550 mm Seat to floor height ±10mm: 400 millimeter Backrest to floor height ±10mm: 1050 millimeter Arms to floor height: 630 mm All steel components should be: Epoxy polyester powder coated(DFT 40-60 microns) Warrantee period in number of years: 3-year

Executive table (Front Table Parishad Hall and conference table) Mode of supply: Knocked Down To Be Assembled At Consignee Site By The Seller Frame type: Free standing Understructure of table Gable end and modesty panel Table top Material: Three layer prelaminated particle board(Wood Product) of grade II type II of IS 12823/Latest Gable end and modesty panel material: Three Layer prelaminated particles board(wood product) of grade II type III of IS 12823/Latest Leg Material: NO LEGS Table top long sides: To be post form half round profile with corner edge bending Table top plain sides: Edge to be banded with PVC tape of 2mm thick with the help of hot melt glue Gable end and modesty panel plain side: Edge to be banded with PVC tape of 2mm thick with the help of hot melt glue Thickness of table top ±2 mm: 25 millimeter Thickness of gable end and modesty panel ±2mm: 19 millimeter Length of table top ±10 mm: 1800 millimeter Depth of table ±10 mm: 750 millimeter Height of table ±10 mm: 725 millimeter Table top finish:Laminate in colour with matt finish 0.6-0.8mm thickness of type S,F or P having index no.3.2.3 conforming to IS 2046/Latest with having balancing laminate of 0.5mm thick on other side Table top shade As per Buyer's choice Warrantee period in number of years: 1

WORLD FURNITURE REVOLVING CHAIR With ARM push back Pedestal Base: ABS Plasstic with ABS/Nylon Twin Caster Wheels Minimum 5 Nos, of 50 mm Size Arm Material: Proypylene seat material: PU Foam covered with Fabric Density of PU foam used in seat KG per Cu Meter (+/- 3): 45 Material of Fabric Back Cover / Material for Backrest: 100% polyester fabric Material of Fabric of Seat Cover: Mesh Fabrics GSM/Thickness of fabric ±5%(Gram/Square meter): 250 gram Chair Type: push back Tilt Tension Adjustment: Yes Height Adjustment ± 5(mm): up to 120 mm Arm: With Type of backrest support: backrest symmetrical lumber support Arm Type: Fixed Colour of Fabric for Seat and Backrest: black Ergonomic Seat Design: Yes Back type: push back Backrest is made of two pcs injection moulded frame: Backrest is made of one piece injection moulded frame backrest has separate adjustable headrest: No Seat type: fixed Seat is curved: Yes Locking mechanism: Yes Type of locking: tilt limitor Lumber support: external & fixed Overall Chair Height ±15mm: 860 Backrest Height ±15mm: 460 millimeter Backrest Width ±10mm: 440 millimeter Seat Height ±15 mm: 450 Seat Width ±10 mm: 480 Seat Depth ±10 mm: 500 millimeter Thickness of MS Plate Joining the under structure with Seat: 0.2 millimeter Thickness of Plywood used in Seat ±1(mm): 15 mm Padestal Size (Diameter in mm) +/- 10 mm: 715 Thickness of Polyurethane Foam Used in Seat in mm (+/- 2 mm): 45 mm Warrantee period in number of years: 1-year

Ergonomic Executive Net High Back Chair with Head Rest Pedestal Base: Chrome finish with 5 wheels Arm Material: steel covered with polyurethane seat material: PU foam covered with mesh fabric Density of PU foam used in seat KG per Cu Meter (+/- 3): 45 Material of Fabric Back Cover / Material for Backrest: Innner frame Upholstered with Mesh fabric and mounted on main assembly Material of Fabric of Seat Cover: Mesh Fabrics GSM/Thickness of fabric ±5%(Gram/Square meter): 250 gram Chair Type: push back Tilt Tension Adjustment:Yes Height Adjustment ± 5(mm): up to 120 mm Arm:With Type of backrest support: backrest symmetrical lumber support Arm Type: Adjustable Colour of Fabric for Seat and Backrest: black Ergonomic Seat Design: Yes Back type: push back Backrest is made of two pcs injection moulded frame: Backrest is made of one piece injection moulded frame backrest has separate adjustable headrest: Yes Seat type :fixed Seat is curved: Yes Locking mechanism :Yes Type of locking: upright locking Number of arm movement: 2(up & down) Lumber support: external & fixed Overall Chair Height ±15mm: 1280 Backrest Height ±15mm: 730 millimeter Backrest Width ±10mm: 550 millimeter Seat Height ±15 mm: 450 Seat Width ±10 mm: 550 Seat Depth ±10 mm: 520 millimeter Thickness of MS Plate Joining the under structure with Seat: 2 millimeter Thickness of Plywood used in Seat ±1(mm): 15 mm Padestal Size (Diameter in mm) +/- 10 mm: 680 Thickness of Polyurethane Foam Used in Seat in mm (+/- 2 mm): 50 mm Thickness of Polyurethane Foam Used in Backrest IN MM (+/- 2 MM): 45 mm Warrantee period in number of years: 3-year

Unbranded Executive Table of Three layer prelaminated particle board(Wood Product) of grade II type II of IS 12823/Latest 1200 millimeter 600 millimeter 750 millimeter Mode of supply: Knocked Down To Be Assembled At Consignee Site By The Seller Frame type: Free standing Understructure of table :Gable end and modesty panel Table top Material: Three layer prelaminated particle board(Wood Product) of grade II type II of IS 12823/Latest Gable end and modesty panel material :Three Layer prelaminated particles board(wood product) of grade II type III of IS 12823/Latest Table top long sides: To be post form half round profile Table top plain sides: Edge to be banded with PVC tape of 2mm thick with the help of hot melt glue Gable end and modesty panel plain side: Edge to be banded with PVC tape of 2mm thick with the help of hot melt glue Number of buffers provided: 4 Nos. at bottom Thickness of table top ±2 mm: 25 millimeter Thickness of gable end and modesty panel ±2mm: 25 millimeter Length of table top ±10 mm: 1200 millimeter Depth of table ±10 mm: 600 millimeter Height of table ±10 mm: 750 millimeter Table top finish: Laminate in colour with swede finish 0.6-0.8mm thickness of type S,F or P having index no.3.2.3 conforming to IS 2046/Latest with having balancing laminate of 0.5mm thick on other side Table top shade As per Buyer's choice Warrantee period in number of years: 1 Test reports to be furnished to buyer on demand :YES Product having BIFMA certification: YES OEM of offered product is ISO 9001:2015 certified: YES OEM of offered product is ISO 14001:2015 certified: YES OEM of offered product is ISO 18001:2007 :YES

EXECUTIVE TABLE StellarR Mode of supply: Knocked Down To Be Assembled At Consignee Site By The Seller Frame type: Free standing Understructure of table :Gable end and modesty panel Keyboard tray: Not provided Foot rest: Not Provided Table top Material: Three layer prelaminated particle board(Wood Product) of grade II type II of IS 12823/Latest Gable end and modesty panel material:Three Layer prelaminated particles board(wood product) of grade II type III of IS 12823/Latest Leg Material: Other wood Table top long sides: Edge to be banded with PVC tape of 2mm thick with the help of hot melt glue Table top plain sides: Edge to be banded with PVC tape of 2mm thick with the help of hot melt glue Gable end and modesty panel plain side: Edge to be banded with PVC tape of 2mm thick with the help of hot melt glue Thickness of table top ±2 mm: 25 millimeter Thickness of gable end and modesty panel ±2mm: 25 millimeter Length of table top ±10 mm :1800 millimeter Depth of table ±10 mm: 900 millimeter Height of table ±10 mm :750 millimeter Width of storage unit ±10mm: 400mm Depth of storage unit in mm (±10mm): 600 Table top finish: Laminate in colour with matt finish 0.6-0.8mm thickness of type S,F or P having index no.3.2.3 conforming to IS 2046/Latest with having balancing laminate of 0.5mm thick on other side Table top shade As per Buyer's choice Warrantee period in number of years: 1 Test reports to be furnished to buyer on demand: YES Product having BIFMA certification: YES OEM of offered product is ISO 9001:2015 certified: YES OEM of offered product is ISO 14001:2015 certified: YES OEM of offered product is ISO 18001:2007 certified: YES

Executive Table V J Interior Mode of supply: Knocked Down To Be Assembled At Consignee Site By The Seller Frame type: Free standing Understructure of table: Gable end and modesty panel Storage provided: Both side Table top Material: MDF board of grade SBG II of IS 12406/Latest Gable end and modesty panel material: Flat single layer prelaminated MDF board conforming to having designation PLMDF-23 of IS 14587/Latest Leg Material: Other wood Table top long sides: Edge to be banded with PVC tape of 2mm thick with the help of hot melt glue Table top plain sides: Edge to be banded with PVC tape of 2mm thick with the help of hot melt glue Gable end and modesty panel plain side: Edge to be banded with PVC tape of 2mm thick with the help of hot melt glue Thickness of table top ±2 mm: 38 millimeter Thickness of gable end and modesty panel ±2mm: 25 millimeter Length of table top ±10 mm: 2100 millimeter Depth of table ±10 mm :950 millimeter Height of table ±10 mm: 750 millimeter Number of Storage unit provided: Triple storage Width of storage unit ±10mm: 400mm Depth of storage unit in mm (±10mm): 600 Height of smallest storage unit ±5mm: 50mm Height of medium storage unit ±5mm: 175mm Height of largest storage unit ±5mm: 230mm Table top finish: Laminate in colour with matt finish 0.6-0.8mm thickness of type S,F or P having index no.3.2.3 conforming to IS 2046/Latest with having balancing laminate of 0.5mm thick on other side Table top shade: Teak Warrantee period in number of years: 2 Test reports to be furnished to buyer on demand: YES Product having BIFMA certification: YES OEM of offered product is ISO 9001:2015 certified: YES OEM of offered product is ISO 14001:2015 certified: YES OEM of offered product is ISO 18001:2007 certified: YES

Unbranded 5 Seater Sofa With Fabric Cover Total Number of Seats in the Sofa Set: 5 Type of Sofa and Backrest: Seat and Backrest are Removable Number of Single Seater Units (Nos): 2 Number of Two Seater Units (Nos): No Two Seater Unit Number of Three Seater Units (Nos): 1 Number of Four Seater Units (Nos): No Four Seater Unit Frame Covering Partially :Upholstered Backrest Cushion Material: Foam Density of Cushion of Backrest Material (Kg/Cubic M): 40 Covering Material for Seat and Backrest :Fabric Frame Structure Material and size (±1 mm): 18 mm thick Teak Plywood Seat Cushion Material: Foam Density of Cushion of Seat Material ±3 (Kg/Cubic M): 40 Type of Spring in the Base / Seating: No Spring in the Base Length of Single Seater Units in mm (±5 mm): 750 Depth of Sofa Units in mm (±10 mm): 700 Sofa Height (Without Back Cushion) ±5 (mm): 400 millimeter Sofa Height (With Back Cushion) ±5 mm: 800 millimeter Arm Width ±5 (mm): 120 millimeter Arm Height ±5 (mm): 550 millimeter Seat Height (With Seat Cushion) ±5 (mm): 450 millimeter Sofa Leg Height ±2(mm): 100 millimeter Sofa Leg Width / Diameter ±2 (mm): 75 millimeter Seat Cushion Length ±5 (mm): 440 Seat Cushion Width ±5 (mm): 380 Seat Cushion Thickness ±3 (mm): 80 Backrest Cushion Length ±5 (mm): 530 Backrest Cushion Width ±5 (mm): 400 Backrest Cushion Thickness ±3 (mm): 75 Thickness of Foam/Rubber in arms ±2 (mm): 50 Thickness of Foam/Rubber in back ±2 (mm): 75 Thickness of Foam/Rubber in front ±2 (mm): 100 Thickness of Foam/Rubber in sides ±2 (mm): 50 Colour of Polish on exposed Wood frame: Teak Finish Colour of Covering Material: As per Buyer's Choice Warranty:1 - Year

BANTIA FURNITURES PRIVATE LIMITED Rectangular CENTRE TABLE with Flat glass Top of 914mmX609mm Mode of supply: Assembled ready to use Shape of the Centre table: Rectangular Style of Centre Table: Supported by set of Legs Design of centre table With four legs only Number of storage under top: Single storage in bottom portion Top material: Flat glass Frame material: Carved Teak wood Leg material: Teak carved wood Material of Understructure supporting the top: Other wood Storage material: Other wood Dimension of Top (length X Breadth) ±20mm: 914mmX609mm Height of centre table ±10 mm: 430 millimeter Thickness of top material (+/-2 mm): 12 millimeter Thickness of frame material (+/- 1 mm): 19 millimeter Thickness of leg material: 35mm X 35mm Thickness of understructure support material: 18 millimeter connecting of leg: Adjacent side of leg Table top finish: Teak laminate/ply with polish Warranty period in number of years: 2

SS CHAIR 3 Seater Public Place Seating Chair of mild steel with arm Type of Seating:Integrated Seat and Backrest Style: with arm and backrest Seating Capacity (Nos): 3 Number of arms (Nos): 2 Delivery status:Assembled Material of Main Frame: mild steel Material of Seat and Backrest :Mild Steel Material of Arms:cold rolled steel Material of Legs:cold rolled steel Material of Side Bar Bracket: made up of chrome plated solid steel Thickness of material of Main Frame in mm: 1.6 Thickness of material of Arms in mm: 1.6 Type of bolts: M12 Bolts Overall Length in mm (±10 mm) :1800 Overall Depth in mm ( ±5 mm): 800 Overall Height in mm (±5 mm): 800 Seat Height from Floor in mm (±5 mm): 425 mm Thickness of material of Seat and Backrest (mm):1.6 mm Colour of Covering Material: red All M S Strucure Finish Enamel Paint Colour of Paint:red All steel component to be epoxy powder coated:60 micron thick WARANTEE PERIOD IN NUMBER OF YEARS: 2 Seat and Backrest are Perforated: Yes Adjuster for legs: No Arms Chrome Plated: Yes Legs Chrome Plated: Yes Cushion on Arms: No

VASSIO Revolving Chair With Arm Asynchronous mechanism Chair mechanism: Asynchronous mechanism Mechanism designed with 360 degree-revolving type and upright locking: Yes Chair included the pneumatic height adjustments: Yes Height Adjustment ± 5(mm): up to 65 mm Armrest: With Type of backrest support: Adjustable Lumbar Support Ergonomic Seat Design: Yes Back type: Fixed Seat type: Fixed Seat is curved: Yes Type of locking: Upright locking Pedestal Base: Nylon base Twin wheel castor material: ABS Number of twin wheel castor: 5 Nos. Twin wheel castor diameter: 50 mm Armrest Material: Polypropylene Seat material: Injection moulded 2 pieces Backrest is made of: One piece injection moulded frame Density of PU foam used in seat KG per Cu Meter (± 3): 45 Density of PU foam used in backrest in KG per Cu Meter (±3): 50 Backrest upholstered with: Leatherette Seat upholstered with: Leatherette GSM/Thickness of fabric ±5%(Gram/Square meter): 220 gram Upholstered material colour: As per Buyer’s Requirement (to be indicated at the time of bid creation) Overall width (±10 mm): 610 mm Backrest Height ±15 mm: 520 mm Backrest Width ±10 mm :360 mm Seat Height ±10 mm :500 mm Seat Width ±10 mm :440 mm Seat Depth ±10 mm: 410 mm Thickness of MS Plate Joining the under structure with Seat: 0.3 mm Thickness of Plywood used in Seat ±1(mm) :15 mm Thickness of Plywood used in Backrest ± 1(mm): 15 mm Pedestal Size (Diameter in mm) ±10 mm :600 mm Thickness of Polyurethane Foam Used in Seat in mm (±2 mm): 35 mm Thickness of Polyurethane Foam Used in Backrest in mm((±2 mm) :35 mm Warranty period in number of years:2-years

RADHE ENTERPRISE Steel Filing Cabinets with 4 Drawers and with central locking machanism Conformity to Indian Standard IS:3313 Latest: No Number of Drawer (NOS): 4 Drawer suspension:Ball Slide (Not as per IS 3313) Lock:Provided Locking Mechanism:central locking machanism Loading Capacity of drawer in kg (+/- 2 Kg):200 kilogram Sheet Thickness of Side, Back, Top and bottom in mm (+/- 5%):0.7 millimeter Sheet Thickness of Filing Drawer in mm (+/- 5%):0.7 millimeter Clutch compressor: strip or Cradle strip MS Sheet (Not as per IS 3313) Overall Height +/- 10(mm): 1300 millimeter Width +/- 10 (mm):475 millimeter Depth +/- 10(mm):600 millimeter Height of smallest Drawer +/- 10(mm):ALL DRAWERS EQUAL Height of medium Drawer +/- 10(mm):ALL DRAWERS EQUAL Height of largest Drawer +/- 10(mm):300 mm Colour of Paint:gray Finish: powder coated Packing:five ply corrugated board and strapped with 12 mm HDPE Strap

DOLPHY Fully Automatic ABS Plastic Hand Dryer Weight :4 kilogram Body Material: ABS Plastic Width: 240 millimeter Height: 240 millimeter Depth: 241 millimeter Motor Speed in RPM: 15000 - 30000 Noise Level: 60 decibel Hand Dry Time/Drying Time Range (sec): Less than 15 Auto Cutoff: 30 second Heater Element: Yes Operation: Fully Automatic Color: White Suitable Traffic: High Blowing Volume (m3/h): >270 Motor Type: Brush Ac Type Air Speed (meter/sec): 30 Protection Class: IP 4 Mounting: Wall Mounted Current 0.5 Ampère Rated Power: 500 Watt Input Voltage: 210 Volt Input Frequency :50 Hertz Warrnaty on Machine: 12 month Warranty on Motor in month: 12

BASIL 7700 Nits Brightness, Outdoor Mild Steel Led Display System Type of LED Display System: Outdoor Material of the Cabinet: Mild Steel Aspect Ratio: 0.672916667 LED Configuration: RGB 3 in 1 SMD Maximum Pixel Pitch (mm): 8 Length of LED Display System (cm): 301 - 310 Height of LED Display System (cm): 181 - 190 Maximum Depth of LED Display System (cm): 15 Pixel Density Minimum (Per Square Metre): 15625 Horizontal Resolution (Pixel): 400 Vertical Resolution (Pixel)(in mm): 240 Horizontal Viewing Angle (degree): 160 Vertical Viewing Angle (degree): 160 Optimal Viewing Distance (meter): >/=8 Refresh Rate (Hz): 1920 Response Time (milliseconds): 5 Frame Frequency (Hz): 50 - 60 Brightness -Calibrated Minimum (Nits): 7700 Contrast Ratio: 208.3340278 Uniformity of Brightness across the Screen: 95 Gray Scale Processing (Bit): 14 Life of Light Source (Hours): 100000 Dimming Capability: 256 levels Fanless Design :Yes Availability of Data Power Redundancy: No Mean Time Between Failure (MTBF)(Hours): >10000 IP Rating (Front): IP65 IP Rating (Rear): IP65 Maintenance: Rear Duty Cycle: 24x7 Availability of Smart PDU: No LED Make: HS Power Input (Volt): 230 Vac +/- 10%, 50-60 Hz Maximum Power Consumption (Per Square Meter): 900 Mounting Arrangement: Wall/Pole Availability of Receiver Card: Yes Earth Leakage Current: <3mA Number of HDMI Port: 1 Number of USB Port: 1 Number of Gigabit Ethernet Port: 2 Wireless Connectivity: Yes If Yes, Type of Wi-fi Connectivity: 802.11ac BIS Registration under CRS of Meity for LED Wall including LED Controller: Yes BIS Registration Number and its validity: R-81006246, 19-11-21 ROHS Compliance: Yes Certifications Available: FCC,CE ISO Certifications: Yes Total Weight of Wall with complete structure and frame (kg): 500 Standard Accessories to be supplied :User Manual,MCB/DCB,Power cable from nearest power point,LAN Cable,HDMI/DVI cable,DVI to HDMI convertor ACP Sheet at top of the structure having depth 450mm to avoid bird drops at Screen: Yes Mounting structure (Mild Steel) with protectomastic primer 100 micron with ACP cladding :Yes Minimum Operating Temperature (degree) :-20 Maximum Operating Temperature (degree): 60 Minimum Operating Humidity (%RH) :5 Maximum Operating Humidity (%RH) :99 Installation and Commissioning is included in Scope of Supply :Yes On Site OEM Warranty (Years): 1

LG Standard Throw (0.91 to 2.5) Multimedia Projector (MMP) With 1920 x 1080 (Full HD) Resolution Number of HDMI In Port: 2 Audio Out: Yes Number of USB Type A: 1 Wireless Screen Share: Yes LAN Connectivity: Yes Technology: One Chip DLP Projection Method: Front Native Resolution: 1920 x 1080 (Full HD) Brightness (Lumens) :500 Contrast Ratio (Minimum) (pixels )( X :1 ): 100000 Availability of Lens: Yes Remotely Controlled: Ye If Yes, Type of Projector: Standard Throw (0.91 to 2.5) Aspect Ratio: 16:09 Keystone Correction :Automatic & Manual Both Type of Light Source: LED Minimum Life of Light Source (In Normal Mode) (Hours): 30000 Lamp Hour Counter (In-Built): Yes Inbuilt Speaker: Yes If Yes, Wattage of Speaker: 2 3D Projection Capability: No Power Consumption in Sleep Mode (Watts): 1 Power Consumption in Normal Mode (Watt): 65 Noise Level in Echo Mode (dB): 25 Noise Level in Normal Mode (dB): 27 Power Supply: 210V-240V, 50 Hz Battery :Yes If Yes, Minimum Battery Capacity (mAH): 6000 If Yes, Battery Backup Time (Hour): 2.5 BIS Registration under CRS of Meity: Yes BIS Registration Number: R-41064670 Dimensions (Length x Breadth x Height) (mm x mm x mm): 170.2 x 48.2 x 170.2 Weight (Kg): 1 Maximum Operating Temperature (Degree C) :40 Minimum Operating Humidity ( % RH): 10 Maximum Operating Humidity ( % RH): 80 On Site OEM Warranty for Light Source (Time or Life in Hours whichever is earlier): 3 Year or 30000 Hrs. On Site OEM Warranty: 3

6feet x 8feet Motorized projector screen Motorized projector screen Type:Motorised Supported Display Technology: 3D Mounting Type:Wall Mount Aspect Ratio:4:03 Display Fabric Material Matte: white Length x Width of Projector Screen (Inch x inch):96*72, 8f x 6f Gain:1.1 Life time lubricated motor for smooth & silent functioning of the screen:Yes Remote:Yes If Yes, Type Of Remote: Wireless Anti UV Coating:Yes Waterproof/Washable:Yes Weight (Kg):10 kilogram On Site OEM Warranty:1

Audio Proton Aluminum Audio Amplifier, Warranty 2 year Width: 510 millimeter Length: 470 millimeter Height: 185 millimeter Weight: 22.6 kilogram Body Material: Aluminum Power: 220 Volt Frequency response (Khz):20 Interface - Input:Unbalanced Input Channels:4 Controlling Features: Must have Gain control per Channel Pack Type:Box Warranty:2 year

EXTRON 12 Channels Audio Digital Signal Processor Maximum Number of Channels: 12 Inputs: Mic / Line Outputs: Main No of Mic Inputs: 12 Nou mberof Line Inputs: 20 Number of Mic/Line Inputs: 12 Number of Phantom Power Inputs :12 USB input for Soft VC: Yes Number of USB channel: 2 USB Bit Depth (Bit): 48000 Frequency Response (Minimum) (Hz): 20 Frequency Response (Maximum) (Hz): 20000 Input Impedance (Ohm): 10000 Output Impedance (Ohm) :150 Phantom Power (Volt): 36 THD(%): 0.001 Sample Rate (dBm): 48 Ethernet Port: Yes PSTN port for telephone :Yes VOIP port for telephone: Yes Configuration Port: USB Dialer Supported: Software AEC: Yes Number of AEC Ports: 12 Number of Line Output :8 Number of Mic/Line Output: 8 Expansion Protocol: Dante Limiter: Yes Filters: Yes Feedback supressor: Yes Mixer :Yes Matrix: Yes Rack Mount Kit: Yes wirelessly Controllable through smart devices :Yes If Yes, type of devices iOS Other Features, if any Configure Software Dimensions (mm x mm x mm) :43x442x241 Weight (Kg): 2.1 Maximum Power Consumption(Watt): Yes Maximum Operating Temperature: 50 degree Celsius Operating Humidity (RH) ($): 90 Other certifications available: UL,CE,FCC,RoHS Availability of Test Reports from Central Govt/ NABL/ILAB acredited lab covering all the declared parameters as per Governing specification No Warranty:3

MEGA PROFESSIONAL AUDIO One Way PA Speaker, Warranty 1 Years Speaker Type: Main Speaker Amplification Method: Passive Speaker Configuration: One Way Number of Speakers: 4 Frequency Response (Hz) :20-20,000 Hz Low Frequency Unit with Size in Inches: 6"X4" Sound Pressure Level (SPL) (1W/1m): (dB) 93 Coverage Pattern :180 Maximum Level Sound Pressure Level :(dB) 93 Speaker Port: Sealed Enclosure Connectors: Stripped Cable Socket Enclosure :Aluminium Sheet Mounting :Wall Mount Dimensions (H x W x D) (mm x mm x mm) :170x170x600 Weight (Kg) :6.4 Power Rating (Watt): 30 AC Power Input: 230V ~ 50/60 Hz Warranty (Years): 1

Ahuja Wireless Cardioid Microphone Specification Form Factor: Handheld If Wireless, Operating Range: 45 meter Polar Pattern / Directionality: Cardioid Microphone Transducer Type: Condenser Frequency Response (Hz) :20-20,000 Hz Equivalent Noise Level (dBa): 100 Signal to Noise Ratio (dB): 25 Electrical impedance (ohm): 5 Sensitivity :-50 dBV/Pa (3.15 mV) LED Indicator :Available On/Off switch :Available Audio Connector Type: 3.5 mm Jack Power Source: 2.9V BATTERIES Operating Temperature Range (Degree C): -05 TO 50 Operating Humidity (RH%): 10 Dimension (W x H x L) (mm): 300 X 200 X 70 Net Weight (Gram): 1.78 kilogram

GLOBUS Wired Cardioid Microphone (Chairman Unit(01 Nos.) With Delegate Unit(08 Nos) & Control Unit(01 Nos.)) Type: Wired Form Factor: Table Top If Table Top, Length of Goose-neck (mm): 400 millimeter Polar Pattern / Directionality: Cardioid Microphone Transducer Type: Condenser Inbuilt Speaker: Yes Frequency Response (Hz): 20-20,000 Hz Equivalent Noise Level (dBa): 85 Signal to Noise Ratio (dB): 70 Electrical impedance (ohm): 4 Sensitivity: -50 dBV/Pa (3.15 mV) LED Indicator: Available On/Off switch: Available Volume Control :Yes Audio Connector Type: XLR Casing Material: Plastic Power Source: AC 230V/50Hz Operating Temperature Range (Degree C): 0to45C Operating Humidity (RH%): 85 Dimension (W x H x L) (mm): 160x170x 65 Net Weight (Gram): 800 gram Warranty (Years): 1

SAMSUNG Smart Television Tv 65 Inch LED Backlit LCD Type of Display Technology: LED Backlit LCD Screen Size (Inches): 65 Resolution (Pixels): (3840x2160) UHD Category: Smart Operating System in case of Smart TV: Tizen Static contrast Ratio: 41.66736111 Typical Brightness: 200 - 299 Screen Mirroring: Yes Mount Type :Both table and wall mount Inbuilt Speakers: Yes If Yes, Wattage of Speakers: 20W x 2 Sub Woofers: No Power Consumption (Watts): 200 Number of HDMI Ports: 3 Number of USB Ports: 1 Number of Ethernet Ports: 1 Built-in Wi-fi: Yes Wi-fi Direct :Yes RF Input: Yes Details of accessories (included in the scope of supply): Remote Control,Connecting Cable,Batteries BIS Registration as per CRS of Meity: Yes BIS Registration Number: R-61001627 Energy Star Rating in line with the Government of Indiia Notification number S O 1896(E) and S O 1897(E): 2 Maximum Operating Temperature (Degree C): 50 Minimum Operating Humidity (%RH): 10 Maximum Operating Humidity (%RH): 90 Dimensions (Length x Breadth x Depth) (mm x mm x mm ): 1449. x 906.x 282. Weight (Kg): 20.9 Warranty(Years):1

MEGA PROFESSIONAL AUDIO Digital 48V Pa Mixer Type: Digital Number of Channels: 16 Inputs: Mic,Line,Mono,Stereo Outputs: Main Signal to Noise Ratio (dB): 70 Impedance (ohms): 600 Built-in USB option: Available Phantom Power (Volts): 48V Computer Connectivity Available Total harmonic distortion (dB): 14 Treble (Hz) :10000 Bass (Hz) :10000 On-board Effects: Yes Number of Faders (Number): 10 Rack Mount Kit: Available Dimensions (mm x mm x mm): 465x110x435 Weight (Kg) :7.9 kilogram Power Consumption (Watt): 220 Operating Temperature Range (Degree C): 50 Operating Humidity (RH %): 80 BIS Registration under CRS of Meity: Exempted Availability of Test Reports from Central Govt/ NABL/ILAB acredited lab covering all the declared parameters as per Governing specification No Warranty (Year) 1

hp Web Camera, Warranty 12 month USB Ceritfication: USB 2.0 high-speed certified Pan(degree): 360 Tilt(degree): 60 Frame Rates(frames per second): 30 OS Compatibility: 10 Fit type: Universal clip fit Auto Exposure: Yes White Balance: Auto White Balance Max. Image Resolution: 5500 x 3640 Focus: 5 cm to Infinity Auto Compensation: Yes Max. Video Resolution: 640x480 Microphone: Built-in high sensitive USB microphone Lens(MegaPixel) :2 Cable Length: 3 foot Width: 51 millimeter Length: 68 millimeter Height: 33 millimeter Weight: 93 gram Time Duration for Repairing /Replace the defect during Warranty Within one month Response Time to attend the complaint during Warranty: 72 Hour Warranty:6 month

Dynamic Rack 42U Smart Rack Type of rack: Smart Rack Size of Rack Enclosure: 42U Mount Type: Free-Standing If Seismic Racks, Earthquake zones: Zone 4 Front glass Door: Yes Type of glass used in front door: Yes, Dynamic Brand Material used for rear door: Yes, Dynamic Brand Rear split door design: Yes Doors with Perforation: Rear Side Panels With Key Locks and Slam Latch: Yes Keyboard Tray Sliding and Rotary: Yes Shelf For Display: Yes Cable channel in rear side for cable management :Yes Support cable entry from top or bottom: Yes Vertical & Horizontal managers: Yes Number of Rack trays: 3 Number of cooling Fan For Heat dissipation: 4 Number of fan trays: 1 Heavy Duty Caster Wheels: Yes If yes, then Front Break Options: Available Load Bearing Capacity (Kgs): 1300 kilogram Secure Locks: Available PDU Power Strips: Available If Available, number of power Strips: 2 Cabinet Lights :Yes Dimensions (H x W x D) (mm): 600*1000*1938 Weight (Kgs): 220 kilogram On Site OEM Warranty (years): 3

MAA ASSOCIATES

RAJ CONSTRUCTION