Provision of hard standing at entrance of each Godowns, storm water drainage system at truck parking/ waiting Area and interlocking tiles in truck parking/ waiting Area and construction of block of Toilets for trucks drivers parking Area at CSD Depot

Amount

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep in soft/loose of soil for foundation, etc. or for shafts, wells, cesspits, manholes, pierholes, etc. and getting out complete all as specified and directed.

M&L for providing PCC (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as foundation filling mass concrete or in sub base of floor complete all as specified and directed.

M&L for brick work with subclass 'B' bricks, straight or curved on plan to any radius built in cement mortar (1:4) as in half brick thick wall (using old size bricks)

M&L for use and waste of form work to sides of concrete foundations, footing bases of column, raft and raft beams and similar work vertical or batter rough finished surfaces of concrete, complete all as specified and directed.

M&L for precast reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in foundations including rafts, footings, foundations beams, plinth beams bases for columns etc basement slabs under reamed piles and mass concrete complete all as specified and directed.

M&L for mild steel TMT bar 10 mm dia & over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia as specified .

M&L for mild steel TMT bar 8 mm dia & over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia as specified .

M&L for rendering 15 mm thick on fair faces of brick or concrete surface in cement mortar (1:6) finished even & smooth without using extra cement complete all as specified and directed.

M&L rendering 15mm thick in cement mortar 1:4 mixed with water proofing compound on fair faces of brick/concrete surfaces rendering is to be finished even and fair without using extra cement . (WPC will be measured and paid separately) including necessary scaffolding if required complete all as specified and directed.

Supply only integral water proofing compound complete all as specified & directed.

Providing and fixing tiled false ceiling of Everest Designer tile lvory plainted (High pressure steam cured) of 4 mm thickness (as per IS 14862) of size 595x595mm and any one of the design (cascade of electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gsm, both side inclusive and black painted groove on all T webs) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30mm sheet, 1200mm long spaced between main "T" at 600mm c/c to from a grid of 1200 x 600 mm and secondary cross "T" of length 600mm and size 15 x 32 mm made of 0.30mm thick sheet to be interolcked at middle of

Item No 11.00 contd .the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including, rquired cutting/ making opening for services like diffusers, grills light fittings, fixtures smoke detectors etc. Main "T" runners to be suspended from ceiling using CI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adustable rods of 3 mm dia with galvanized butterfly level clips or with 3 mm dia GI wire, spaced at 1200mm c/c along main "T" bottom exposed width of 15mm of all T Section shall b pre painted with polyster paint and black painted groove at center or size 4mm depth and 4mm all complete all as specified by Engr-in-Charge. including dismantling of old celing board inclduing cover fillets and removing from site.

M&L for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering/cladding to wall fixed with self tapping screws, complete all as specified and directed.

S&F structural steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St. 240 as in frame work for sun shade, roof projection etc. complete all as specified and directed.

S&F alluminium anodized barrel tower bolt extruded section 200mm length of bolt, ISI marked complete all as specified.

S&F 50 mm size aluminium handles,cast type,anodised all as directed ISI marked complete all as specified and directed.

S&F 100 mm size mild steel butt hinges medium weight cold rolled fixed/ welded to steel frame ISI marked complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples all as directed by Engineer- in -Charge.

S&F of mild steel framed work such as grills, gratings etc, with ends of bars shouldered and /or riveted, or forged into pikes, framed guard bars, barred iron doors, ladders, framed balsters, walk ways, railing, frame work of water tanks and similar work conforming to Fe- 410-0 Gde Fe 410-0 complete all as specified and directed.

S&F pre laminated Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam single piece extruded pvc profile and edgs will be painted to match with prelam sheet , PVC sheet are to be reinforced with 19x19mm MS square tube EPDM rubber gasket weather seal shall be provided through out the frame. The profile shall be mitre cut at two corners and joint by insrting 2 nos of 150mm long backets of 15mmx15mm MS square tube inside the 19mmx19mm MS square tube and suitably screwed and fixing in opening as per specification & drawing.

S&F Factory made pre laminated solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with single piece extruded pvc profile both side prelam PVC sheet 'C' channel having a 5mm thick PVC sheet strip of 20mm width stuck inside with solvent cement, forming stiles, and 5mm thick both side prelam single piece extruded pvc profile for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of both side prelam 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and shown on drawing given in SSR Part II. The width of stiles & rails shall be in proportion to the width of the door shutter as given in SSR Part I.

M&L for hard core of broken stone or boulder of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc. 15cm thick, watered and well rammed to a true surface complete all as specified and directed.

M&L for 75 mm thick cement concrete (1:4:8) type D-2 (using 40mm graded stone aggreate) as in sub base, finishing the surface even and rough to received tiles.

M&L 40mm th PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in sub base floor, complete all as specified and directed.

M&L non skid ceramic coloured tiles 7 to 8mm thick area of each tile exc 0.6 Sqm n exc 0.11 Sqm as in floor set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match the surface of tile including 15 mm thick screed bed in bedding layer (1:6) complete all as specified and directed.

M&L for coloured Glazed ceramic tiles in vertical surfaces of size 300mm x 200mm, 7mm thick over and including 10 mm thick bedding layer in CM (1:4) , set and jointed in neat cement slurry and pointed in white cement mixed with coloured pigment to match complete all as specified and directed.

M&L cutting chases, pinning in, making good to facing where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good cutting not exc 10cm girth.

S&F glavanised mild steel tube, medium grade with all fittings and fixed complete to walls and ceiling or laid in floor for 15 mm bore ISI marked complete all as specified & directed.

S&F glavanised mild steel tube, medium grade with all fittings and fixed complete to walls and ceiling or laid in floor for 20 mm bore ISI marked complete all as specified & directed.

S&F vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest fixed with cement joint and providing lime concrete bedding and connecting to flusing cistern including 'P' or 'S' trap of CI complete all as specified and directed.

S&F chromium plated bib taps long body, fancy type, with round headed knob or , screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F stop valve 20 mm nominal bore (ISI marked) brass, screwed down high pressure with cluch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts, of 450 mm length complete all as specified and directed.

S&F PVC, white, low level flushing cistern 8 ltr capacity with all fittings syphonic action push type with inlet ball valve and float with & including PVC flush pipe 32 mm bore complete all as specified and directed

S&F 100mm dia cast iron soil waste and vent pipe (sand cast pipe) in an length with or without ears laid with cement joint in trenches or fixed to walls.

S&F 75mm dia cast iron soil waste and vent pipe (sand cast pipe) in any length with or without ears laid with cement joint in trenches or fixed to walls.

S&F 100 mm dia CI connection sanitary connection short connections pipe of length upto 300mm complete all as specified and directed.

S&F vitreous china wash hand basin, white flat back, size 580x450mm excluding taps, waste pipe chain and plug and porcelain but including brackets all as specified

S&F 15 mm dia pillar taps, cast copper alloy with capstan head chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed all as directed

S&F 75mm Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) complete all as specified and directed

M&L for preparation of new surface of wall and applying two coat of cement base paint of wall over a coat of white wash complete all as specifed

M&L for preparation of new plastered surface of wall and applying three coat of white wash complete all as specified

M&L for Brickwork with sub-class `B’ bricks, straight or curved on plan to any radius in half brick thick walls built in 1:4 complete all as specified

M&L for use and waste form work for fair finished surface to sides of concrete walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses etc vertical or to batter, complete all as specified and directed.

M&L for use waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete.

M&L use and waster of formwork to edges of concrete flats, treads, breaks in floor, window cills, concrete railing, opening in concrete wall, sides of RCC slab, RCC/ PCC bends in walls or similar work thickness exc. 10 cm and not exc 20 cm in rough finished surfaces of concrete complete all as sepcified and directed.

Matertial and labour for R.C.C (1:1.5:3) (using 20mm graded crushed stone aggregate) for Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed

Matertial and labour for R.C.C (1:1.5:3) (using 20mm graded crushed stone aggregate) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L cement concrete type B-2 (1:2:4) (using 40mm graded aggregate) in surface channels and drains all as specified and directed

Removing excavated material exc. 250 m but n exc. 500 m and depositing complete all as specified and directed by Engr-in-Charge with in MD land.

M&L for two coats synthetic enamel paint on steel surfaces over a coat of red oxide primer of any description including preparation of new surfaces exc. 10 cms in width or girth complete all as specified and directed

Surface excavation n exc 30cm deep averaging 15cm deep in any type of soil and getting out complete all as specified and directed by Engr-in-Charge.

M&L for 100mm thick PCC (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L for 100mm thick PCC (1:1.5:3) type A-1 (using 20 mm graded crushed stone aggregate) as in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L for 200 mm deep and 12mm thick forming Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ complete all as specified and directed.

Surface rolling in cutting/filling including water and consolidating formation surface with vibromatic roller all as directed by Engr-in-Charge.

M&L for 100mm thick PCC (1:1.5:3) type A-2 (using 40 mm graded crushed stone aggregate) as in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L for rubber module precast cement concrete interlocking paver block, any shape and size confirming to IS 15658-2006, of 100mm tickness, M-50 grade, in floors laid over sand coushing 25 mm thick and filling of gap with dry sand complete all as specified all as directed by Engineer-in-Charge. (Note:-Sand filling shall be measured and paid separately)

S&f vitreous chinaware unrinal half stall 60cm long any size including CP connector for flushing and all fitting and fixed to walls complete all as specified and directed.

M&L for Point wiring with1100 Volts, grade 1.5 Sqmm. (nominal area) ,PVC insulated but unsheathed multistranded copper conductor single core FRLS cable drawn through and including non metallic medium duty rigid PVC concealed conduit (medium duty) 20mm dia or higher complete with all accessories such as socket, elbow, junction box, bell mouth, bend, reducer etc including pressed iron/steel suction box of thickness1.2mm for mounting of switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable as earth wire upto common earth and connected to earth dolly complete all as specified and directed by Eng.-in-charge of following. Note:- Wire/cable colour coding shall be maintained properly as per IE rule. The make of conduit & its accessories should be Precision/Polycab/AKG/Modi. The make of wire should be Finolex/Polycab/Havells/L&T/BCH

(a) One light point controlled by one-one way switch.

All as per item No.60.00 above but with 2.5 Sqmm. (nominal area) wire/cable for phase and neutral for one 3 Pin 15 amp socket on independent board including one 1.5 sqmm PVC insulated unsheathed multi stranded copper conductor cable, FRLS 1100 volts grade as earth continuity conductor upto common earth & connected to earth dolly complete all as specified and directed by Eng.-in-charge.

S&F switch piano flush button type 15 Amps SP 250 Volt AC complete all as specified & directed. Make: SSK/CONA/Leader.

S&F socket outlet 2-in1,3 pin 5 and 15 Amp flush type 250V AC complete all as specified & directed. Make: SSK/CONA/Leader.

S&F switch piano flush, button type 5 Amp SP 250 Volt AC complete all as specified & directed. Make: SSK/CONA/Leader.

S&F ceiling rose surface bakelite 3 terminals of size 65x25mm. complete . Make: CONA/SSK/Leader

S&F lamp holder PVC/polycarbonate type with LED lamp 9/10 watt (Make of LED bulb wipro/philips/CG)complete all as specified & directed.

S&F wall mounted tube light fitting 1x20/22 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 6500K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed. Make:Wipro Cat part No LL20-221-XXX-65-NE/ Philips cat part No BN021C LED20S PSU CWGR S2/Havells Cat No ENDURA LINEARNEOBS20W LED840SPCWH.

S&F wall mounted tube light fitting 1x 10 watt or higher ,extruded aluminium polycarbonate durable LED batten with decorative end caps, PF 0.9 and above operating voltage 150V-300V colour temp 5700K & lumen input output 90 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed. Make: Philips cat part No BN021 LED10S-6500PSU GRS1/ Wipro Cat part No LL20-111-XXX-65-NE or equt in OSRAM /GE Lighting

S&F Bulk head luminaire with Cast aluminum rectangular shape canopy, Stove enameled paint both side. Heat resistance glass with rubber gasket protected with wire mesh guard. B22 porcelain holder with and including retrofit LED lamp 9 watts complete all as specified and directed by Engr-in-charge. Make : Make : Mepro cat part No BC-77 (W/G) or eqvt in Philips /Bajaj.

Disconnecting and taking out U/S DB any capacity. S&F sheet metal enclosures 240 volt with suitable rated bus bar for double door 4 way IP-43 DB's suitable for one MCB SPN as incoming and 6 MCB SP as out going, mounting flush on wall/concealed and making good distubed surfaces complete all as specified and directed by Engr-in-charge. Make: Legrand/L&T/Schneider.

S&F MCB SPN 240 Volt 10 KA 40 Amp 'B' series conforming to IS complete all as specified & directed. Make: Legrand/L&T/Schneider.

S&F MCB single pole 240 volt, 10 KA, 40 Amp, 'B' series confirming to IS complete all as specified and directed. Make: Legrand/L&T/Simens/Schneider.

Supply & fix Double ball bearing motor, Heavy duty exhaust fans totally enclosed, Rust proof body & blades, Aluminium pressure die cast, Dynamically balanced blades for vibration free & Noiseless operation, AC single phase, 6 pole power input 55 or higher wattage, 900 RPM, 230/ 240 V of size 300 mm sweep with suitable louver incl provisioning of 3 core white flexible multistranded copper conductor 23/0.0076 from ceiling rose to fan connector complete all as specified and directed by Engineer-in-charge. Make : Havells : Turbo force 1 phase, or Crompton model EXHD300-6-1(ISI) marked or equivalent in Orient.

M&L for making suitable size hole in wall for fixing exhaust fan upto 300mm sweep in any type of wall including grouting of four nos hold fastners/Tee bolts of suitable size etc for fixing of exhaust fans to wall complete all as specified and directed incl making finishing surfaces of wall, distempering as per existing shade complete all as specified by Engineer-in-charge.

M&L for Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level, earth plate surrounded by and packed with a 15 cm thick layer of char coal dust and common salt, earth lead GI wire 4.00 mm. dia by means of bolts, Nuts, Check Nuts and washers of galvanized iron and thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe medium 15 mm. bore, and water pipe 20 mm. bore GI light grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 & 75 mm thick RCC (1:2:4) type B1 cover slab reinforced with 8mm TMT bars 100mm c/c both ways complete all as specified & shown in elect plate No. 3 of SSR part I of 2009 and testing on completion.. Note: (i) If the desired earth resistance is not found within permissible limit shall be redone by contractor at no extra cost. (ii) Cost of GI wire 4 mm and 15 mm dia pipe medium grade upto 7.5 mtr is included in the rate quoted for this item

Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed 1100 Volts grade, nominal cross sectional area 16 Sqmm 2 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including jointing and testing including all bare conductor duly insulated with heat shrinkable sleeves / Taflon tape complete all as specified and directed by the Engr-in-Charge. Make of Cable : KEI/Havells/Finolex

Returning, filling in excavated soil, including leveling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and as directed by the Engr-in-Charge.

Removing excavated material (soil) not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting Point complete all as specified and as directed by the Engr-in-Charge.

M&L for sand cushioning in trenches for protection of UG cable with river bed sand laid dry in trenches before and after laying of cable, including well ramming and consolidation complete all as specified and directed.

M&L for providing of new sub class 'B' bricks, old size, well burnt laid flat dry for protection of under ground cable complete all as specified and directed.

Supply and laying in replacement of GI Steel tubing medium grade 40 mm dia laying in trenches or grouting/fixing in wall for protection of cable complete all as specified and directed by Engineer-in-charge Make : Jindal/TATA/BST/ Swastik

M.K Engineers

Gupta Brothers

M/s Anil Kumar

M/S C S AITHANI