SPECIAL REPAIRS TO B/R WORKS INCL ROOF TREATMENT TO BLDG NOS. P 67 P 118 P 151 P 152 AND P 377 AND PROVN CERTAIN REV AND MINOR WORKS AT MIL STN GNADHIANGAR

Amount

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth for foundation of pole, laying of cables etc in soft/loose soil and getting out.

Returning, filling in, including spreading, leveling, watering and well ramming in layer not exc 25 cm with soil obtained from excavation.

Excavation in post holes (or similar holes) each not exc 0.5 cum, getting out, in soft/loose soil including returning, filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25 cm, watering and removing surplus soil to a distance n.exc 50m and making good surfaces complete all as specified and directed.

Removing excavated material (Soil) not exc 50 mtr and depositing where directed at a level not exc. 1.5 m above the starting point.

Removing rubbish to a distance exc. 1.5 Km but not exc. 5.0 KM out side MD land complete all as specified and directed.

M&L for hard core of gauge not exc. 63mm deposited spread and levelled in layers not exc. 15 cm thick, spread, levelled and rammed to a true surface including watering complete all as specified and directed.

M&L for plain cement concrete (1:4:8) type D2 using 40 mm graded stone aggregate in foundation filling and mass concrete complete all as specified and directed.

M&L for plain cement concrete (1:3:6) type C-2, using 40 mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B-0, using 20 mm graded stone aggregate in roof kerbs coving fillets of 75mm radius at junction roof slab and parapet wall, vertical surface and like etc. complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate for padestal/coping around poles, including necessary form work, finishing even and smooth without using extra cement, all as specified and directed.

M&L for providing precast cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in lintels, copings apex stone, pier caps, columns, posts, boundry pillars, bed plates, anchoage blocks, bonders (stone walling), corbles brackets etc with plain fair faces, including chamfers weatherings, throating etc and setting in cmeemnt mortar 1:4 complete with joints to match all as specified.

M&L for RCC M-25 ( Design Mix ) ( using 20mm graded stone aggregate ) as in suspended slabs supported on walls/columns, in floors, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for cutting uneven surfaces of concrete & cutting reinforcement from drops of fins & facias (thickness not exceeding 50mm) using necessary scaffolding and making good the disturbed portion with 10mm thick rendering in CM 1:3 finished even and smooth without using extra cement etc. complete all as specifeid and directed.

Preparation for water proofing treatment to roof slab by applying one coat of cold bituminous primer @ 0.30 litre/sqm and confirming to IS-3384, laying APP based polystr modified membrane reinforced non wooven polyster of 3.50 kg/sqm (minimum) 3mm thick with plain polythene finished and sealing all the overlap 75mm in length side and 100mm in width side of membrane by torching including applying one coat of bituminous aluminium paint over membrane all as specified and directed.

Supply only, liquid water proofing compound complete all as specified and directed.

M&L for Brick work with old size, sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for cutting holes into or through brick walls built in cement mortar superfical area not exc 150 sq. cm and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified and directed.

M&L for form work to soffit of suspended slabs such as roof slabs, floor slabs, landings and simillar works not exceeding 20cm thick and rough finished surfaces of concrete all as specified and directed.

M&L for form work to sides and soffit of floor or roof beams, beams haunchingss, girders, brussummers, lintels, cantilevers, shelves including sup-ports, overhangs, etc and rough finished surfaces of concrete all as specified and directed.

S&F, 30mm thick flush shutters, solid core construction, with block board core and plywood face panles, commercial type on both sides complete all as specified and directed.

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 200 mm and fixed complete all as specified and directed

S&F, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 300 mm and fixed complete all as specified and directed.

S&F, butt hinges, medium weight, cold rolled, mild steel of size 125 mm complete all as specified and directed.

S&F, extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed.

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars, shouldered and/or riveted, or forged into spikes, framed guard bars etc and similar work conforming to Fe-290 (Gde-E-165) complete all as specified and directed

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for mild steel TMT bars, 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bend to shape required and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F, MS angle iron Fe-410-W (Gde-E-250) quality A in framed work for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc complete all as specified and directed.

M&L for rolled mild steel angle iron work as in door frames complete, drilled for fixing of hinges etc. also fastening and fixing conforming to Fe-290 (Gde-E-165) complete all as specified and directed.

S&F, in repair, 0.56mm thick aluminium anodised sheet fixed with steel screws at 300mm as in covering to crumple joints complete all as specified and directed.

S&F, 0.63mm thick plain galvanized mild steel sheeting in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 all as sp[ecified and directed.

M&L for cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3, all as specified and directed.

S&F, 20mm thick bituminus board strip 30cm width fixed bituminus crumple joint all as specified and directed.

M&L for 50mm thick cement concrete 1:3:6 type C-1, using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

M&L for 100 mm thick cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate as in sub base of flooring/hard standing and finishing the surface even and fair without using extra cement complete all as specified and directed.

M&L for 50mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in floors and finishing the top surface even and smooth without using extra cement complete all as specified and directed.

M&L for 40mm thick cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate as in roof padding laid in slope 1:30 including finishing surfaces fair and even complete all as specified and directed.

Taking down cement plaster on brick or stone wall etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for rendering cement plaster 10mm thick in cement mortar (1:6) on brick work or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering cement plaster 10mm thick in cement mortar (1:4) over the bed of PCC surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for screed bed 15mm thick on fair faces of concrete surface in cement mortar (1:3) mixed with using water proofing compound by weight of cement as per manufacturer instructions, finished even and smooth without using extra cement for laying APP membrane at non -accessible roof (mumty) complete all as specified and directed. Note:- Supply only liquid water proofing compound shall be measured and paid separately.

M&L for rendering 15mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering cement plaster 5mm thick in cement mortar 1:4 on fair faces of concrete in ceilings, chajjas, fins facia etc. finished even and smooth without using extra cement complete all as specified and directed.

M&L for screed bed 20mm thick on green surface of roof slab in cement mortar (1:3) complete all as specified and directed.

M&L for preparing new plastered or un-plastered walls surfaces and applying three coats white wash complete all as specified and directed.

M&L for preparing old plastered or un-plastered walls surfaces and applying one coats of white wash on walls complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of white cement as primer complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall and applying one coat of cement base paint complete all as specified and directed.

M&L for preparing new plastered or un-plastered surfaces of walls and applying two coats of oil bound distemper over and including chalk whiting on walls complete all as specified and directed.

M&L for preparing new plastered or un-plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M&L for preparing old plastered or un-plastered surfaces and applying one coat of white wash on ceiling complete all as specified and directed.

M&L for preparing old plastered or un-plastered surfaces and applying three coat of white wash on ceiling complete all as specified and directed.

M&L for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc. 0.5sq.m in each pane complete all as specified and directed.

M&L for preparation of new wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over existing shop coat of primer complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for preparation of previous untreated of small articles such as metal switch blocks, metal ceiling roses, articles of builder's hardware such as door springs, hooks, knobs, fasteners, stays, locks, latches, etc., straps to roof trusses, gates and similar articles, when unconnected with other painting or when painted in a different tint 2 coat of synthetic enamel over one coat of red oxide zinc crome all as specified and directed.

S&F, factory made steel windows with side hung shutter including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded including applying one shop coat of red oxide primer complete all as specified and directed.

Taking up or down steel tubing and connections for 15mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 20mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 25mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 40mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 15mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 20mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 25mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 40mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 15mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 20mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 25mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 40mm bore of pipe complete all as specified and directed.

Supply, hoisting, fixing in position and connecting, 1000 litres capacity rotational moulded polyethylene water storage tank double layered (cylindrical, vertical with closed top), ISI marked, including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size all as specified in SSR Part-I complete all as specified and directed.

Supply, hoisting, fixing in position and connecting, 500 litres capacity rotational moulded polyethylene water storage tank double layered (cylindrical, vertical with closed top), ISI marked, including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size all as specified in SSR Part-I complete all as specified and directed.

Disconnecting, setting aside (or lowering if required) and Cleaning & removing all scale and dirt etc from HDPE water tanks of 1000 litres capacity (Tanks placed on top of roof) and from mouths of circulating pipes etc including washing the tank with bleaching powder and hoisting, reconnecting and re-fixing in position including writing the date of cleaning of tank with synthetic enamel (black/white) paint of size not less than 10cm of each letter complete, all as specified and directed.

S&F, CP Brass bib cock long body with capstan head handle screwed down suitable for 15mm bore fitting all as specified and directed.

S&F, Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all as specified and directed for 20mm bores of pipe.

S&F, Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all as specified and directed for 25mm bores of pipe.

S&F, 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed.(Minimum weight -210 Gms)

S&F, in repair, HDPE water storage tank lid black (with arrangement for locking) for 1000 litres capacity tank complete all as specified and directed.

S&F, 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or floor complete all as specified and directed.

S&F, 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or floor complete all as specified and directed.

S&F, 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls including stack clamp complete all as specified and directed.

S&F, 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls including stack clamp complete all as specified and directed.

S&F, 75mm bore PVC (SWR) plain bend, any radius complete all as specified and directed.

S&F, 110mm bore PVC (SWR) plain bend, any radius complete all as specified and directed.

S&F, 75mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed.

S&F, kitchen sink with drainage board made of stainless steel 1mm thick including supply and fix 32mm CP waste coupling, plug, washer, 32 mm bore and 60cm long PVC waste pipe including cantilever brackets made of mild steel angle iron 30x30x4mm and flat iron 25x3mm both duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, cutting for and pinning in ends of brackets to errecting stand into wall and making good disturbed portion in cement mortar 1:2 or in PCC 1:2:4, type B-1 using 20mm graded stone aggregate and connecting union to pipe, over all size 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Removing existing water proofing /black top treatment except concrete padding ruighing of concrete surface cleaning and washing down the surface with water and removing debrish/rubbish material to a distance exc. 1.5 Km but not exc. 5.0 Km out side Md land complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc. 15cm thickness (below or above ground level) all as specified and directed.

Demolition of reinforced cement concrete of manhole covers etc complete all as specified and directed.

Dismantling of cast iron, PVC or reinforced concrete drain pipes jointed in cement mortar for 110mm and 75mm bore of pipe from wall/floors etc complete all as specified and directed.

Shree Builders

ALBA AC AND REF SERVICES

Ramdev and Sons

Electricals India

Sharnamsingh and Co

GIRNAR CONSTRUCTION