Completion of incomplete work in respect of certain Misc repair to roof, flooring, etc at New MH, 501 FSEG, 447 ASC Sup Depot, TA Bn, EME Wksp and connected area under AGE B/R-I of GE Dehradun.

Amount

Dismantling of asbestos cement (corrugated semi corrugated, etc) sheet in roof covering etc complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge and thickness including Nainital or similar pattern roofs covering including ridges complete all as specified and directed.

S&F 6mm thick asbestos cement corrugated or semi corrugated sheets in roofs wall etc and fixed with coach screws complete all as specified and directed.

S&F plain galvanized mild steel sheeting 0.63 mm thick in ridges, hips, valley gutters, drips and straight flashing complete all as specified and directed.

S&F 0.63mm Galvanized corrugated mild steel sheeting with two corrugation side lap, fixed with coach screw and washers, in roofs, walls etc of following classes: (having zinc coating 275 gm/sqm) complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPA as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling of timber scantlings 40 Sqcm and over in section in any position and in any situation. (unframed work) complete all as specified and directed.

Dismantling of timber scantling 40 Sqcm and over in section, in any position as in Framed work complete all as specified and directed.

Dismantling of wrought iron or mild steel work any description and fixed in any position complete all as specified and directed.

S & F of rolled mild steel sections as in roof trusses (framed), trussed, purlins, crane gantries, rails, fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections), including distance pieces, cleats etc. including cutting, welding etc. confirming to Fe – 410 – W(Gde E - 250) quality 'B' complete all as specified and directed.

S & F of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 complete all as specified and directed.

S & F of mild steel work in hand rails, half round or other steel section or core for wooden hand - rail straight portioon, drilled and countersunk for balusters, nosing of steps, including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe – 290 Gde E - 165 complete all as specified and directed.

Dismantling of expanded metal any thickness or mesh fixed steel or wood fillets if any, weight not exc. 4.00 Kg per Sqm complete all as specified and directed.

S & F of expanded metal cut to length, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9 mm dia or fixing with galvanised steel staples and fixed to wood or steel members, weight per Sqm not exc. 4 Kg complete all as specified and directed.

M&L second class hard wood in scantlings, clean sawn (SAL) fixed in any position complete all as specified and directed.

M&L preparing surfaces of wood & wood based material of any description and girth not otherwise described and treated with two coats of creosete oil complete all as specified and directed.

Dismantling of wall and ceiling boards (fiber, pulp, insulation etc.) or insulation boards / slabs / blankets, any thickness including cover fillet complete all as specified and directed.

S&F 4 mm thick E-Board (Classic) in false ceiling including and fixing of frame work made of special section MS galvanised sheet with zinc coating cellular nitro painting and consisting of angle cleats of size 25 mm wide 1.6 mm thick with flag fixing to the ceiling with dash fastner 12.50 mm x 40 mm long or with 2 mm dia GI wire or fixed with bolt in GI channel main 45 x 14 x0 .90 mm thick and cross runner 25 x 25 x 0.5 mm for fixing E board of size 600 x 600 x 4mm thick including fixing of E board with ceiling section and paremeter of channel 25 x 25 x 0.50 mm thick, 27mm high flange of 20 mm to 30 mm long extra including applying two coats of oil bound distemper complete all as specified and directed.

Taking down Aluminium window shutter size n.exc 1 Sqm including opening up of the corner junctions and replacement of defective members (matching with existing material) alongwith necessary cleats, butt hinges and refixing in the same opening to make the window functional complete all a specified and directed. (Note : - Butt hinges and anodised aluminium section shall be measured and paid separately.)

Taking down Aluminium door shutter size exc 1 Sqm but n.exc 2 Sqm including opening up of the corner junctions and replacement of defective members (matching with existing material) alongwith necessary cleats, pivots, locks and refixing in the same opening to make the door functional complete all as specified and directed. (Note : - Butt hinge ,Pivot, locks and anodised aluminium section shall be measured and paid separately)

Taking down Aluminium door shutter size exc 2 Sqm including opening up of the corner junctions and replacement of defective members (matching with existing material) alongwith necessary cleats, pivots and refixing in the same opening to make the door functional complete all as specified and directed. (Note : - Butt hinge, Pivot, Floor spring and anodised aluminium section shall be measured and paid seperately)

S & F aluminium section for doors, windows with one or more rebates including joining cleats for fixing etc, complete all as specified and directed.

S&F in repair glazing (5.00 mm thick float glass) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket and aluminium snap beading etc. complete all as directed by Engineer-in-charge . (Note : - Cost of aluminium snap beading and EPDM rubber/ neoprene gasket shall be paid and measured seperately)

S& F in repair 12 mm thick prelaminated particle board in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete all as directed by Engineer-in-charge (Note : - Cost of aluminium snap beading shall be paid and measured seperately)

S&F 100 mm size Butt hinges, extruded aluminium alloy with galavanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F 75 mm size Butt hinges, extruded aluminium alloy with galavanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

Supply only anodised aluminium snap beading complete all as specified and directed.

Supply only EPDM rubber/ neoprene gasket complete all as specified and directed.

S&F in repair Double action floor spring of approved brand and manufacturer conforming to IS: 6315 hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and making good to floor to match with existing floor complete all as specified.

S&F in repair aluminium (extruded section) Door closer hydraulically regulated, designation No.1 universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed with stainless steel screw complete all as specified and directed.

S&F 100 mm brass dead locks (best make of approved quality) for aluminium door including necessary fittings etc complete all as specified and directed.

S& F bright finished brass governing pivot fixed at top stile and frame of aluminium door with necessary brass screws etc. complete all as specified and directed.

S&F in repair anodised aluminium casement/ peg stays, size 300 mm long with hinged joint and two plates, with studs including necessary fittings etc, complete all as specified and directed.

S& F in repair extrudued aluminium alloy handles, fabricated type 150 mm long incl fixing with stainless steel screws complete all as per specified and directed.

S&F in repair 300 mm long Aluminium alloy, anodised sliding door bolt with hasp, staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed with stainless steel screw complete all as specified and directed.

Taking down of chowkhats or frame with shutter of any description (without taking off shutter from the frame) n.exc 1.50 sqm each complete all as specified and directed.

Taking down of chowkhats or frame with shutters of any description (without taking off shutters from the frames) exc 1.50qm and n.exc 4.00 sqm each complete all as specified and directed.

Taking down of shutter of any description exc. 1 sqm and n.exc 2 sqm each complete all as specified and directed.

M&L Framed work as in door or gate angle or other section prepared for hanging and sliding with and including hooks and hinges and steel gate doors fittings Fe-410-W. E-250 quality 'B' complete all as specified and directed.

S & F of 0.80 mm thick mild steel plain black sheet in hearth; covering of door shutters; covering to door chowkhats (frames), chullah hoods, water tank, water troughs; ducts; urinal troughs and funnels etc., cut to size, edges beaded if directed, holes punched including round headed screws, clout nails or rivets and fixed to wood or steel members etc. with plain 40 mm lap joints with welded / rebated seams including bending, turning up, mitred angles, stopped ends, outlets etc. as required complete all as specified and directed.

S&F 18 to 20 mm thick solid PVC board for cupboard shutters with one side 1 mm thick printed PVC sheet other side plain PVC sheet including suitable fixed to MS guiding runners with and including suitable PVC frame as per specification and drawing complete all as specified and directed.

S & F of 40 mm wide flap when open, mild steel bright finish or electro galvanised continuous (Piano) hinge complete all as specified and directed.

S & F of 75 mm long Brass handles, cast type, polished bright complete all as specified and directed.

S&F magnetic catcher of brass for cabinets fixed with screws complete all as specified and directed.

S & F of 35 mm thick (Batten thickness) factory made plain, framed, panelled shutters (Two panels) with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces and size of the members of shutter are as per IS – 1003 (Part – I) made of kiln seasoned & chemically pressure treated 2nd class hardwood complete all as specified and directed.

S & F of 35 mm thick (Batten thickness) 2nd class hardwood factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), chamfered or rounded, mitered and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and size of the members of shutter is as specified in clause No. 8.24 (a) of MES schedule part – I (Specifications - 2009) complete all as specified and directed.

S&F Solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tales all as specified under Srl No. 884 of Sch 'A' Part II 2004 and its corresponding sketch complete all as specified and directed.

S & F 30 mm thick (style thickness) factory made solid panel PVC shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheets beading and joined together with solvent cement as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F of steel window with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S & F of steel window with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F of steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed.

S&F powder coated aluminium anodised door with frame, shutter, following accessories and glazing 4.8 mm thick retro reflected glass, rubber gasket, aluminium glazing clips, mortice lock, aluminium stopper cleat, iron mongary, section of aluminium door shall be of following sizes: - Frame: 100x44x1.20 mm thick with rawl plug ,Middle lock rail: 85x44x1.20 mm thick, Bottom rail : 150x44x1.20mm thick, Top rail : 85x44x1.20 mm thick, style : 75x44x1.20 mm thick, glazing bead : 0.70 mm thick, Aluminium handle 'D' type : 150 mm, Aluminium tower bolt 9.9 mm dia shoot 200 mm long, Mortice lock: 100 mm 4 lever, Aluminium stopper cleat, aluminium hinges 100 mm long Note: PCC shall be measured and paid seperately and making good of wall surface with matching to existing surface complete all as specified and directed.

S&F alumnium anodised partition wall with alumium frame and parttions of rectangular section of size 85x44x1.20 mm thick fixed in position partly with glazing 5 mm thick antilio glass and partly 12 mm thick PVC board with 0.70 mm thick glazing beading and rubber gasket including fixing on wall and floor with suitable size of steel chromium plated screw with rowel plug complete all as specified and directed.

S&F anodised aluminium window & ventilators incl shutters & frame with anodised aluminium sections of following size incl glazing clips anodised aluminium snap beading complete all as specified. Aluminium section 15 micron thick anodising aluminium section size shall be as under - Frame (65x40x1.20 mm) thick, shutter top & bottom rail (44x44x1.20mm ) thick, stile and side rail (44x44.5x1.20 mm) thick . Glass 4.8 mm thick reflected glass fixed with rubber gasket with aluminium beading, Aluminium fittings such as peg stay 300 mm long, aluminium hinges 75 mm size & handle 100 mm long, aluminium tower bolts 100 mm long complete all as specified and directed.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F Aluminium (Die Cast body) Door closer hydraulically regulated designation No 1 universal type suitable for door shutters up to 851 mm to 1000mm in width and of weight between 61 to 80 kg and fixed complete all as specified & directed.

S&F Stainless steel 100mm long Butt hinges complete all as specified and directed.

M&L 200 mm long aluminium anodized tower bolt , fabricated type complete all as specified and directed.

M&L 150 mm long aluminium anodized handle fabricated type complete all as specified and directed.

S&F 250 mm long Aluminium alloy, anodised sliding door bolt with hasp, staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed with stainless steel screw complete all as specified and directed.

S&F in repair 20 mm dia bore aluminium drapery rod with wooden finish, decorative, including brackets, decorative finials at both ends & curtain rings 8 Nos (minimum) complete all as specified and directed.

S&F mild steel framed work as in grills, grating etc. with end of bars shouldered and/or riveted, or forged into spikes: frame guard bars: barred iron doors: ladders: frame balusters: walk ways: railing: frame work of water tanks and similar works confirming to Fe- 410 or F-310-0 complete all as specified and directed .

S & F of 100 mm long mild steel butt hinges, medium weight cold rolled complete all as specified and directed.

S&F 300 mm long mild steel sliding door bolts, stove enameled black with bright blot not less than 12mm dia with and incl a miximum of 6 blots and nuts, four on bolt plate and two on staple plate and fixed 300mm long complete all as specified and directed.

S&F MS barrel tower bolt 200mm, stove enamelled black with bright bolt and fixed complete all as specified and directed.

S&F MS pressed bow handles 125mm size oval type stove enamelled black complete all as specified and directed.

S&F stainless steel wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.18 mm with tinned tack or galvanised wire stappler complete all as specified and directed.

Hacking out old broken glass (any thickness), size quality or description from wooden frames glazed with putty or fixed with beads complete all as specified and directed.

M&L for 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

Demolition of brick work or stone/boulder masonary built in cement mortar incl all quoins arches pillars etc. complete all as specified and directed.

M&L brick work with sub class ‘B’ bricks old size straight or curved on plan exc. 6 mtr mean radius built in CM (1:6) complete all as specified and directed.

M&L brick work with sub class ‘B’ bricks old size straight or curved on plan exc. 6 mtr mean radius in half brick thick wall built in CM (1:6) complete all as specified and directed.

Taking down of cement or cement lime plaster any description from brick or stone wall etc. including raking out of joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L rendering 15 mm thick cement plaster in CM 1:4 on brick & concrete surfaces and finished even and smooth (without using extra cement) with and including WPC @ 3% by wt of cement complete all as specified and directed. Note :- WPC shall be measured & paid separately under respective item of Sch "A"

M&L, preparation of new plastered/un plastered surfaces and providing two coats of cement base paint over a coat of primer as in walls complete all as specified and directed.

Demolition of cement concrete (un-reinforced) of any description and laid in any position complete all as specified and directed.

M & L for providing pre-cast cement concrete in door or window cills, lintel, bressumers, bed plates, apex stone, pintle blocks, bonders (For stone masonry) and similar items with plain faces including chamfers, weathering, throating etc. in cement concrete 1:2:4 type B-1, using 20 mm graded stone aggregate and setting in cement mortar 1:4 complete all as specified and directed.

M&L PCC 1:4:8 type D-2(using 40mm graded stone agg) as in foundation of drain, filling , mass concrete, subase floor, etc complete all as specified & directed

M & L for plain cement concrete(1:2:4) ( Nominal Mix (using 20 mm graded stone aggregate) as in surface channel or drain or benching in manhole complete all as specified and drected.

M & L for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitered / stopped ends etc. complete all as specified and directed.

M & L for PCC 1:2:4 type B-0 (using 12.50 mm graded stone aggregate), as in copings including necessary form work as required complete all as specified and directed.

M&L preparing of new plastered or un plastered surface of walls and applying two coats of oil emulsion distemper complete all as specified and directed.

M & L for preparation of wall and applying wall putty 2 to 3mm thick to make the surface smooth complete all as specified and directed.

M&L for preparation of new painted or previously untreated wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new painted or previously untreated steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Demolition of cement concrete in ground floor and paving n.exc 15cm thick below or above ground level including floor tiles etc complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding but not backing and removing rubbish off the premises complete all as specified and directed.

M & L for providing 40 mm thick PCC 1:2:4, type B-1 (using 20 mm thick graded stone aggregate) as in floor, laid in panels and position to conform to design and finishing top surface even and smooth without using extra cement complete all as specified and directed.

Supply only glass dividing strips, 3mm thick 38mm width complete all as specified and directed.

M&L 25mm thick PCC 1:2:4 type B-1 (using 20mm graded stone agg) for sub base to receive the screed complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:4 for receiving tiles as in backing complete all as specified and directed.

M&L screed bed or bedding layers of mortar 15 mm thick for laying floor finishes in CM 1:6 complete all as specified and directed.

M&L Glazed ceramic tiles coloured size of size 200 x 300 x 6 to 7mm , as on vertical surfaces such as skirting, dados etc set and jointed in neat cement slurry and pointed in white cement to match complete all as specified and directed.

M&L for heavy duty coloured tiles with chequerred, plain or recess finish at top of size 300x300x 8 to 10 mm thick as in floor set and jointed in neat cement slurry ans pointed in white or coloured cement to match the existing surface over and including bedding layer of mortar 15 mm thick in Cement mortar 1 : 6 for laying floor finishes complete all as specified and directed.

M&L non skid ceramic coloured tiles (300x 300mm) x 7 to 8mm thick in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

M & L for Non skid ceramic coloured tiles (square / rectangular) of 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exc. 0.18sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

M & L for Vitrified Ceramic tiles light shade / double charged / ultrachared polished (square / rectangular) of 10mm thick, area of each tile exceeding 0.36 sqm but not exc. 0.42sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

M & L for chequered cement concrete tiles of size 25cm X 25cm X 20 mm thick with grey cement and pigment set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile as in floor complete all as specified and directed.

M & L for 20 - 25 mm thick machine cut Kota stone slab as in flooring over 15 mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including necessary grinding, rubbing, rounding to exposed edges and polishing in granite finish complete all as specified and directed.

M&L for 15 to 18 mm thick 50 to 75 mm wide stone border in floors of jaisalmer stone with and including over screed bed or bedding layer 15mm thick in CM 1:6 complete all as directed.

M & L for 20 - 25 mm thick machine cut Kota stone slab as in risers of steps, skirting, dado and pillar over 15 mm thick rendering in CM 1:4 , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including necessary grinding, rubbing, rounding to exposed edges and polishing in granite finish complete all as specified and directed.

M & L for 60 mm thick Machine pressed precast concrete interlocking paver block with grey cement and no pigment any shape and size confirming to IS 15658-2006, M-35 grade as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile including and over 25mm thick layer of sand complete all as specified and directed

M&L cement concrete 1:3:6 type C-2 (using 40mm graded aggregate) 75 mm thick as in plinth protection surface finished even and smooth without using extra cement in alternate bays complete all as specified and directed.

Taking up or down 15mm bore steel tubing with connection including cleaning for refixing or removal from site complete all as specified and directed.

Taking up or down 20mm bore steel tubing with connection including cleaning for refixing or removal from site complete all as specified and directed.

Supply, fixing, laying & testing 15 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Supply, fixing, laying & testing 20 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Cutting chases for concealed water tubing and making good in CM 1:3 on brick wall cutting n.exc 10 Cm in girth complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks 500 Ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling of water tank and remove from site complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks 1000 Ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling of water tank and remove from site.

S&F in repair 20 mm bore stop valve cast copper alloy scewed down high pressure with crush butterfly handle screwed both end fixed for iron pipe as specified.

S&F 20 mm dia ball brass valve high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed all as specified and directed.

S&F in repair vitreous china squatting pan Orrisa pattern of size 580x440mm white with integral foot rest including connecting to trap and flush pipe anti-syphonic pipe incl provision of lime concrete complete including making good to floor.

S&F in repair vitreous China wash down (EWC) water closet pan(pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) but including seat and cover for pedestal pattern complete all as specfied and directed.

S & F Vitreous China Half stall type urinals, white, with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (excluding of fixing supply pipe, flushing cistern, flush pipe, trap and waste pipe) complete all as specified and directed.

S&F in repair PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action push type with inlet ball valve and float including flush pipe long 32mm dia, ball valve, handle, bracket etc. complete all as specified and directed.

S & F in repair for Wash Hand basins, Vitreous China, white, flat back, size 550x400mm, including cutting for and pinning in ends of brackets or erecting stand, angle bracket (but exclusive of fixing of supply, waste pipe, taps) complete all as specified and directed.

Supply and fixed in repair pillar taps 15mm bore cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts, screwed to iron pipe & fixed.

Supply only pillar taps 15mm bore cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts, screwed to iron pipe & fixed.

Supply only 32 mm dia waste fittings, brass chromium plated for Glazedware sink, WHB, etc with long screwed shanks and flynuts, flange embedded in red lead cement and other end fixed complete all as specified and directed.

S&F in repair 15 mm dia bib taps wall flange, brass, fancy type CP with crutch or butterfly handles screwed down to GI pipes or for brass ferule or to GI socket complete all as specified and directed. Make- Zim (Viva/Mona Series) cat part No. VI-02 or equivalent in Hindware/ Jaquar.

S&F in repair bib taps long body, brass, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed. Make:- Zim Cat Part No. VI-04 or equivalent in Hindware/ Jaquar.

S&F in repair 15mm dia chromium plated brass sink mixer with swivel spout (wall mounted) or mixing hot and cold water, screwed down for 15mm bore GI pipe complete all as specified & directed. Make - Hindware Cat Part No. F110020 or equivalent in Parryware/ Jaquar.

S & F in repair 15 mm dia CP brass Wall mixer with provision of over head shower complete with 115 mm long bend pipe, connecting legs & wall flange complete all as specified & directed. Make ZIM Cat Part No. VI-17 (Viva Series) or equivalent in Parryware/ Jaquar.

S & F in repair 15 mm dia CP brass centre hole basin mixer (pillar tap) with accessories in wash basin for mixing hot and cold water, screwed down for 15 mm dia bore GI Pipe complete all as specified and directed. Make:- ZIM Cat part No. VI-13 (Viva series) or equivalent in Parryware/ Jaquar.

Supply & Fixing PTMT 45 cm long (PVC connection) 15 mm bore size complete all as specified & directed.

S&F in repair CP brass angle cock 15 mm bore complete all as specified & directed. Make : - Zim/ (Viva Series) Cat part No.VI-05 or equivalent in Parryware/ Jaquar.

S&F angular cock, (2 in 1),15 mm nominal bore, brass, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and directed. Make:- Zim Cat Part No. VI05A or equivalent in Parryware/ Jaquar.

S&F in repair CP shower rose with or without swivel joints of 125 mm size complete all as specified and directed .

S&F in repair sinks made of stainless steel 1 mm thick kitchen or laboratary with plug washers and waste including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting unions to pipe over all size 495mmx420mm bowl size 410mm x330x 160mm complete all as specified and directed.

S&Fin repair CP brass jet for EWC complete all as specified & directed.

S&F in repair CP health fauset, hand shower type with 8mm dia 1 meter long flexible type & wall hook and jet of suitable for 15 mm bore iron pipes or for unions and fixed complete all as specified and directed. Make:- Zim Cat Part No. 1622 or equivalent in Parryware/ Jaquar.

S & F in repair acreylic glass corner shelf with CP brass railing size not less than 300 mm long and fix to wall with rawl plug and CP screws complete all as specified and directed. Make Jaquar, Cat Part No ACN-1173 or equivalent in Parryware/ Hindware.

S & F in repair toilet paper holder, brass, CP box type fixed to wall with chromium plated brass screws and rawl plugs complete all as specified and directed. Make: Hindware Cat Part No. F 830006 or equivalent in Parryware/ Jaquar.

S & F in repair soap dish, brass, chromium plated,100X100X60mm, fixed to wall with rawl plugs and chromium plated screws complete all as specified and directed. Make: Hindware Cat Part No. F 830003 or equivalent in Parryware/ Jaquar.

S & F in repair 20 mm dia brass chromium plated tubular towel rail 'D' type 60 cm long between flanges, including one pair of fixing brackets complete all as specified and directed.

Supply only PVC waste pipe flexible type 32 mm dia complete all as specified and directed .

Demolition and breaking up drain pipes of 100/75 mm bore (salt glazed stoneware, AC or reinforced concrete) set in cement mortar complete all as specified and directed.

S&F cast-iron soil waste and vent pipe 100 mm bore in any length with or without ears with cement joint laid in trenches or in floor complete all as specified and directed.

S&F 100 mm bore cast-iron bends (any radius) disminishing pieces or tappers (larger bore measured) complete all as specified and directed

S&F cast-iron soil waste and vent pipe 75 mm bore in any length with or without ears with cement joint laid in trenches or in floor complete all as specified and directed.

S&F 75 mm bore cast-iron bends (any radius) disminishing pieces or tappers (larger bore measured) complete all as specified and directed.

S&F cast-iron floor trap 75mm bore with CP grating including jointing to waste pipe in cement joint concrete (1:2:4) type B-1 complete all as specified and directed.

S & F of 75 mm bore Cast Iron soil, waste and vent pipe, sand cast pipe, in any length, with or without ears, with cement joints in cement sand mortar 1:1 with spun yarn fixed to walls complete all as specified and directed.

S & F Stack clamps made out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, incl nut and bolts and securing ends of stay to wall or roof for 75 mm bore CI pipe complete all as specified & directed.

Demolition of Re-inforced Cement Concrete in any position and any description including cutting of reinforcement bars to facilitate demolition complete all as specified and directed.

M & L for providing 50 mm thick pre-cast cement concrete louvers or RCC Jali made out of cement concrete 1:2:4 type B-0, using 12.5 mm graded stone aggregate and set in cement mortar 1:4 including all mouldings etc. complete all as specified and directed.

M & L for use and waste of formwork to soffits of RCC Shelves and similar works not exc. 200 mm thick horizontal or slopping in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to edges of RCC Shelves or similar work thickness exc. 05 cm and not exc. 10 cm in rough finished surfaces of concrete complete all as specified and directed.

M&L RCC 1:2:4 type B-1 (using 20 mm graded stone agg) as in slab and shelves supported on walls complete all as specified & directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M& L Udaipur green stone on flooring & RCC Shelves 12 to 15 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab with and including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 finished including rounded of edges of stones complete all as specified and directed.

Cleaning of septic tank/ Soakage well of upto 250 users by removing sludge in semi solid or liquid state, manually or by pump including removal of sludge to a distance exc 1.5 KM but n.exc 5.00 KM out of MoD land complete all as specified & directed. Note ;- measurment will be taken only after dewatering of the septic tank and no extra payment will be made for dewatering the same.

Cleaning of (SGSW) pipe line 150 mm bore size by rodding or by pressure pump complete incl connected manholes, any depth & removal of sludge etc to a distance exc 1.5 KM but n.exc 5.00 KM out of MoD land complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep in soft/loose soil for foundation, etc. or for shafts, wells, cesspits, manholes, pierholes, etc. and getting out complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers n exc 25 cm thick in soft/ loose soil complete all as specified & directed.

Removing excavated material ( soils) to a distance not exc 50M and depositing where directed at a level not exc 1.50 M above the starting point complete all as specified & directed.

Demolition and breaking up drain pipe ( SGSW) set in cement mortar of 150 mm bore complete all as specified & directed including PCC benching complete all as specified & directed.

M&L salt glazed stone ware (SGSW) drain pipe of internal dia 150 mm laid in trenches and jointed in CM 1:1 colpete all as specified and directed grade 'A' complete all as specified & directed.

M&L cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) to bed of drain pipes including packing under and hunching against the sides of pipes, after they are laid and tested for 150 mm bore pipe complete all as specified & directed.

M & L for providing pre-cast cement concrete landing, cover slabs (for man holes etc), chullah hoods, chajjas, water troughs, mangers, shelves and similar items with plain faces in cement concrete 1:2:4 type B-1, using 20 mm graded stone aggregate and setting in cement mortar 1:6 complete all as specified and directed.

S & F of 450 mm bore reinforced concrete pipe Spigot & socket type, class NP-2, laid & jointed in cement sand mortar 1:1 with spun yarn complete all as specified and directed.

Supply only integral water proofing compound as per manufacturer instructions complete all as specified and directed.

S & F of 600 mm bore reinforced concrete pipe Spigot & socket type, class NP-2, laid & jointed in cement sand mortar 1:1 with spun yarn complete all as specified and directed.

SM CONSTRUCTION COMPANY

PRAGATI ENTERPRISES