REPAIR TO PLASTER, FLOORING, JOINERY, PLUMBING AND OTHER B AND R WORKS IN ZONE-B AND ZONE-C AT DEFENCE LAB JODHPUR

Amount

Taking down cement or cement lime plaster, any description on brick or stone walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified & directed by Engineer-in-charge.

M&L 15 mm thick , plaster in cement mortar (1:6) on stone masonry wall surfaces or surfaces other than fair faces of brick work or one side of lathing and finishing the surface even and smooth without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion paint of approved tint over a coat of primer complete all as specified & directed by Engineer-in-charge.

M&L rendering 10 mm thick plaster in cement mortar (1:3) on concrete surfaces of ceiling and finishing the surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L preparation of new plastered surfaces of ceiling and applying two coats of distemper oil emulsion paint of approved tint over a coat of primer complete all as specified & directed by Engineer-in-charge.

M&L rendering 15 mm thick plaster in cement mortar (1:4) mixed with WPC on stone masonry wall surfaces or surfaces other than fair faces of brick work or one side of lathing and finishing the surface even and smooth without using extra cement all as specified & directed by Engineer-in-charge. Note :- WPC will be measured & paid seperately as supply only).

M&L preparation of new plastered surfaces of wall and applying two coats of cement base paint over one coat of primer complete all as specified and directed by Engineer-in-charge.

M&L preparing new or old plastered surfaces of walls and applying two coats of water based paint (exterior emulsion) over a coat of professional exterior wall primer complete all as specified & directed by Engineer-in-charge. (APEX ULTIMA from Asian or equivalent make).

Supply only integral water proofing compound all as specified & directed by Engineer-in-charge.

M&L preparation of old plastered surfaces of walls by complete removing existing treatment and applying two coats of distemper oil emulsion paint of approved tint complete all as specified & directed by Engineer-in-charge.

M&L preparation of old plastered surfaces of ceiling by complete removing existing treatment and applying two coats of distemper oil emulsion paint of approved tint complete all as specified & directed by Engineer-in-charge.

M&L preparation of old plastered surfaces of walls by complete removing existing treatment and applying one coat of birla wall care putty( 2 to 3mm thick) to get a uniform smooth surfaces complete all as specified & directed by Engineer-in-charge.

M&L applying two coats of distemper oil emulsion paint over a coat of primer on birla wall care putty surface of walls complete all as specified & directed by Engineer-in-charge.

M&L preparing old plaster/ concrete/stone surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soof, moulds, moss and efflorescent salts and trading oil and greasing spots and applying two coats of cement base paint complete all as specified & directed by Engineer-in-charge.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not other wise specifically provided and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed by Engineer-in-charge.

M&L reinforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified & directed directed by Engineer-in-charge.

M&L Mild steel TMT bars 10mm dia and over as in reinforcement cut to length bent to shape required including bending,cranking and hooking ends and binding with and including MS wire (annealed) not less than 0.90mm dia complete all as specified & directed by Engineer-in-charge.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings,shelves and similar work, not exceeding 200mm thick (Horizontal or sloping) for rough finished flat surfaces all as specified & directed by Engineer-in-Charge.

Form work to edges of concrete flats,treads,breaks in floors,window cills,shelves,concrete railings,openings in concrete walls,floors and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls,horizontal or sloping and similar work exc 5cm but nexc 10cm wide rough finished surfaces complete all as specified & directed by Engineer-in-Charge.

Demolition of cement concrete unreinforced in ground floors, kota stone, granite flooring, tiles flooring and pavings not exceeding 15cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed by Engineer in charge.

M&L 75 mm thick cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in flooring/ hard standing path in alternate bays area not exceeding 2 Sqm each panel & joints filled with bitumen mastic (1:3) i.e.one part of bitumen and 3 parts of sand, and concrete surface even & smooth without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L 25mm thick PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate as in floors & finishing the surface even & fair without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L Dark shade/Double charged/ultracharged, vitrified tiles, 10mm thick (minimum), (square/ rectangular polished, area of each tiles exceeding 0.36 Sqm (including 600mmx600mm size) but not exceeding 0.42 Sqm, in flooring set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles including 15mm thick screed bedding in CM 1:4 complete all as directed by Engineer-in-charge.

M&L vitrified tiles of dark shade/Double charged/ultracharged, 10mm thick (minimum) (square/ rectangular) polished area of each tiles equal to or exceeding 0.36 Sqm but not exceeding 0.42 Sqm, in skirting/dado(cut to size as required) etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour tiles over and including 10 mm thick backing coat in CM 1:4 complete all as specified and directed by Engineer-in-charge.

M&L18 to 20mm thick granite stone slab machine cut bedded and jointed with grey cement slurry and pointed with white cement or coloured cement to match the colour of granite as in flooring/over cooking plateform etc over and including 15mm thick screed bed in cement mortar (1:6) complete all as specified & directed by Engineer-in-charge.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins arches, pillers etc but excluding ashlar facings, dressed stone work and precast concrete articles and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed by Engineer-in-charge.

M&L Brickwork with sub-class 'B' bricks,straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified & directed by Engineer-in-charge.

M&L Brickwork with sub-class 'B' bricks,straight or curved on plan exc 6m mean radius wall built in CM 1:6 complete all as specified & directed by Engineer-in-charge.

M&L 100 mm thick precast cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in solid block masonry and setting in cement mortar 1:6 complete all as specified & directed by Engineer-in-charge.

M&L squared rubble walling, Jodhpur type, regular courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) complete all as specified & directed by Engineer-in-charge.

M&L squared rubble walling, Jodhpur type, regular courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) except stone complete all as specified & directed by Engineer-in-charge.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exceeding 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses or regular course complete all as specified & directed by Engineer-in-charge.

Racking out joints/ pointing to squared rubble masonry built in cement mortar or cement lime mortar, coursed or uncoursed in walls not less than 12mm deep, washing the joints, removing rubbish off the premises and keeping the surface to pointed or plastered wet for two days prior to re-pointing or plastering complete all as specified & directed by Engineer-in-charge.

M&L keyed pointing in cement mortar (1:3) mixed with white cement and pigment to match the colour of stone to squraded rubble masonary coursed or un coursed complete all as specified & directed by Engineer-in-charge.

Taking down chowkhats or frames not exceeding 1.5 Sqm with shutters (without taking off shutters from the frame) complete all as specified and directed by Engineer-in-charge.

Taking down chowkhats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutters) complete all as specified and directed by Engineer-in-charge.

S&F 30 mm thick flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides complete all as specified & directed by Engineer-in-charge.

S&F 35mm thick factory made 2nd class HW glazed and skelton shutter and open rebated and prepared to receive glass, gauge etc (without sash bars), edges or framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part-I Section 8 Clause 8.24 (a) complete all as specified and as directed by the Engineer-in-charge.

S&F 100mm size, butt hinges, medium weight, cold rolled mild steel including necessary welding if required complete all as specified and directed by Engineer-in-charge.

S&F 300mm long mild steel sliding door bolts plate type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as directed by Engineer-in-charge.

S&F 150mm long, mild steel, barrel tower bolts, stove enamelled black with bright bolt complete all as specified and directed by Engineer-in-charge.

S&F, 150 mm long, mild steel, pressed handles, oval type, stove enamelled black complete all as specified and directed by Engineer-in-charge.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aparture 1.40mm and fixed with stainless steel wire stapples complete all as specified & directed by Engineer-in-charge.

S&F in repairs stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aparture 1.40mm and fixed with stainless steel wire stapples complete all as specified & directed by Engineer-in-charge.

M&L preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified and directed by Engineer-in-charge.

M&L preparing old wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint of approved tint complete all as specified & directed by Engineer-in-charge.

S&F, rolled mild steel framed work as in doors or gates of angle or other section confirming to Fe 410-W (Gde E-250 quality-A) with gusset plates, rails braces, etc., complete, drilled for fixing of steel sheeting or other covering door etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door, fittings and hanging, also fastering and fixing complete all as specified & directed by Engineer-in-charge.

M&L preparation of new or previously untreated steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint of approved tint over a coat of red- oxide, zinc chrome primer complete all as specified & directed by Engineer-in-charge.

M&L preparation of old steel surface of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint (ordinary tint) complete all as specified & directed by Engineer in charge.

S&F solid PVC door frame of size 50 x 47mm made out of 5mm plain colour PVC sheet re-inforced with M.S. square tube supplying and fixing in opening as per specification and drawing in SSR Part II, complete all as specified and directed by Engineer-in-charge.

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strips of 20mm width stuck inside with solvent cement for tiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed the stiles and rails with suitable PVC Sheet beading and jointed together with solvent cement supplying and fixing in the frame at site all as per specification and drawing in SSR Part-II , complete all as specified and directed by Engineer-in-charge.

S&F, 100mm size, butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin,anodised type B-21 including necessary welding if required complete all as specified & directed by Engineer-in-charge.

S&F 200mm size aluminium anodised barrel tower bolts of extruded section complete all as specified and directed by Engineer-in-charge.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engineer-in-charge.

Taking down shutters of any description area exceeding 1.0 Sqm but not exceeding 2 Sqm each and refixing the same opening with necessary fittings complete all as specified and directed by Engineer-in-charge.

M&L 0.90 mm thick decorative laminated type 1 of surface finish, colour and pattern as approved,fixed with approved adhesive as per manufacturer's instructions complete as directed by Engineer-in-charge.

S&F Anodised aluminium frame for doors,windows,ventilators with one or more rebated including jointing cleat for fixing etc complete all as specified and directed by Engineer in charge.

S&F Anodised Aluminium door shutters,aluminium section weighting 0.55Kg/m including necessary joint cleats,glazing clips,ruber neoprene packing,handles 2 Nos in each door,hinges,anodised aluminium snap beading screws etc complete all as specified and directed by Engineer-in-charge.

Refixing old existing Anodized Aluminium partition panel /section from one location to another in office premises and fixing on PCC Floor/tiling/wall tiles with necessary screws by drilling in position and making necessary repair to aluminium partition if requied complete all as specified & directed by Engineer-in-charge.Note :- rates are included for glass pane,pre-laminated sheet in aluminium partition should be taken out from frame and refixing in the same opening including necessary jointing cleats,glazing clips,rubber packing,anodised aluminium snap beading,screws,anodised aluminium fittings etc.

S&F anodized aluminium window and ventilator shutters,side hung type without sash bars,aluminium sections weight not less than 0.55 Kg/Rm including jointing cleats aluminium snap beading/screws,anodised aluminium fittings such as peg stays 150mm long (1 Nos),hinges type B-21 100 mm long(2Nos) suitable handle (1 Nos) complete all as specified and directed by Engineer-in-charge.

S&F Aluminium grill type D or any other type as approved ( weight of grill not less than 2.625Kg/ Sqm without frame) with frame complete all as specified & directed by Engineer-in-charge.

S&F,Solar control film 25 micron reflective type (graveware sun control or equivalent) complete all as specified & directed by Engineer-in-charge.

S&F 12 mm thick pre laminated particle board exterior grade both side laminated in panel of partition or any other location complete all as specified & directed by Engineer-in-charge.

Cutting chases,pinning in, macking good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings,steps ,cills,sunshades, shelves, lintels,etc; and cutting chases for concealed water tubing or concealed conduit wiring,etc and making good,cutting not exc 10 cm girth complete all as specified and directed by Engineer-in-charge.

Taking up or down 15mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-charge.

Taking up or down 20mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-charge.

S&F GI tubing (ISI marked) 15mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed by Engineer-in-charge.

S&F GI tubing (ISI marked) 20mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed by Engineer-in-charge.

Fixing only GI tubing (ISI marked) 15 mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floors obtained from taking down complete all as specified and directed by Engineer-in-charge.

Fixing only GI tubing (ISI marked) 20 mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floors obtained from taking down complete all as specified and directed by Engineer-in-charge.

S&F in repairs brass chromium, fancy type, bib taps, with crutch or butter fly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge.

S&F in repairs, stop valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butter fly handle, screwed both ends for 15mm bore iron pipe or for unions complete all as specified & directed by Engineer-in-charge.

S&F in repairs 10 ltrs capacity PVC valve less, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, complete all as specified and directed byEngineer-in-charge.

S&F in repair vitreous china wash basin white, flat back of size 550 x 400 mm white including waste fittings, brass chromium plated waste coupling, waste pipe, brackets including cutting for and pinning in ends of brackets errect stand, fixing waste pipe ,15 mm bore pillar tap,cast copper alloy,chromium plated with capstan head,screwed down high pressure,with or without letters Hot or Cold with long screwed shank and fly nuts,screwed for iron pipe,PVC connection pipe,15 mm size and 450 mm long with PTMT nuts and washer at both end , complete all as specified & directed by Engineer-in-charge.

S&F in repairs vitreous china squatting pan "Orissa" pattern, size 580 x 440mm white, with integral foot rest (Excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe,lime/cement concretebedding and making good to the floor complete all as specified and directed by Engineer-in-charge.

S&F in repairs vitreous china squatting pan "Orissa" pattern, size 580 x 440mm white, with integral foot rest (Excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe,lime/cement concretebedding and making good to the floor complete all as specified and directed by Engineer-in-charge.

S&F in repair, viterous china urinal half stall type,white including,cantilever bracket complete with grating and union for discharge pipe including providing & fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cementetc complete all as specified and directed by Engineer-in-charge.

S&F in repair fancy type, chromium plated brass wash basin mixer with hot & cold arrangement for 15mm bore complete all as specified & directed by Engineer-in-charge.

S&F in repair ceramic laboratory sink(white) rectangular shape of 600 x 450 x250 mm white including waste fittings, brass, chromium plated, coupling, waste pipe, brackets including cutting for and pinning in ends of brackets errect stand, fixing waste pipe complete all as specified & directed by Engineer-in-charge.

M&L 75 mm size cast iron floor, trap, with grating including jointing to waste pipe fixed in cement conrete (1:2:4) type B-1 including taking down old un-serviceable floor trap complete all as specified & directed by Engineer-in-charge.

S&F in repairs CP grating for Nahani trap/ floor trap of size 100/75 mm bore complete all as specified & directed by Engineer-in-charge.

S&F in repair PVC connections 450mm long, 15mm size with PTMT nuts for WHB, flushing cistern, geysers etc complete all as specified & directed by Engineer-in-charge.

S&F in repair CP brass water jet spray suitable for EWC complete all as specified & directed by Engineer-in-charge.

S&F in repair, gun metal globe or gate valve, with iron wheel head, screwed both ends for 20 mm bore iron pipe complete all as specified & directed by Engineer-in-charge.

Dismantling of old unserviceable PVC water tank of 1000 Ltrs capacity complete all as specified and directed by Engineer-in-charge.

S&F 1000 ltrs capacity rotational moulded polythene water storage tanks white three layered (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I including PTMT ball valve heigh pressure with epoxy coated aluminium rod and high density plastic ball suitable for 20mm bore pipe weight not less than 210gms complete all as specified and directed by Engineer-in-charge.

Dismantling plain or corrugated steel sheeting , any gauge, thickness, including nainital or similar pattern roof coverings complete all as specified & directed by Engineer-in-charge.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheeting 0.50 mm thick any colour having tensile strength 550 Mpa as in roof coverings/cladding to wall, fixed with self tapping screws etc complete all as specified & directed by Engineer-in-charge.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheeting 0.50 mm thick any colour having tensile strength 550 Mpa as in roof coverings/cladding to wall, fixed with self tapping screws etc complete all as specified & directed by Engineer-in-charge.

S&F 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with 'L' or 'J' type or cranked hook bolts complete all as specified & directed by Engineer-in-charge. NOTE:-The work will be carried out at 8to10 metre height above ground level in workshop complex of roof covering / cladding with proper safety precautions .

Demolition wall and ceiling boards/PVC wall lining (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets and frame work complete all as specified & directed by Engineer-in-charge.

M&L ceiling with gypsum board 12mm thick over and including approved GI frame work, hanging rods etc including two coats of plastic emulsion paint over one coat of primer (the rate quoted shall be inclusive of refixing electrical fitting, light etc) complete all as specified and directed by Engineer-in-charge.

SNEH CORPORATION

vinayandsons

M/S Dharam Chand Lal Chand Jain