Street Light work from Jalaram temple to maruti bunglow at Ankleshwar.

Name Of Work : Street Light work from Jalaram temple to maruti bunglow at Ankleshwar.

Sr.No. Item Description Quantity Total Rate Unit Amount

Supplying and erecting approved make Octagonal

pole made from HR sheet steel. The pole should be

made as per IS. and shall be coated with hot dip

galvanizing as per IS 2629/2633/4759, suitable

suspend local wind speed with integral Junction

box consist of terminal plate of min 6mm Hylam

sheet, standard profile 35mmX7.5mm Din-Rail for

MCB Mounting, stud type terminal and

arrangement for cable termination to be erected

With Suitable foundation (Included) as per details

given by manufacturer considering site

requirement. (E) 7 Mtr. Long 70 mm Top X

mm bottom dia, 3 mm thickness with

225mmX225mmX16mm base plate, 4-M20 Bolts

and 600mm long with necessary G.I. J Bolts

.Approx Pole weight 67 kg

Supplying, erecting, testing, commissioning approved

make M.S. Polygonal High Mast Pole having following

general Specification. (a) Polygonal Section fabricated

from M.S. Plate confirms BSEN 10025 & Hot deep

galvanized minimum 65/86 micron (as per IS

/1985) Lantern carriage with ring and rubber lines for

erection of luminaries of suitable site. (b) Maximum

telescopic section not more than four (c) Double drum

gear pipe motorized winch with 6mm dia S.S. Rod (For

16 mtr and above size) (d) Approved make L.E.D.

aviation light = 1 No. Lightening arrestor = 1 No. with

necessary wiring of 2.5 sq.mm 5 core ISI copper cable

Unarmoured. (e) Bottom most section suitable for

mounting reversible motor and switchgears having door

2 not more than 1400mm x 300mm with waterproof 1.00 141616.14 Ea

gasket & hinges & locking arrangement. (f) Pole

structure comprises suitable size of reversible motor,

cable and necessary switchgears with control panel. (g)

bottom section shall have suitable size of thickness

supports ribs foundation bolts nuts etc.(h) Item not

comprises the cost of lanterns. (i) Necessary Cement

Concrete foundation as per IS including testing &

commissioning of the entire structure for following size

of High Mast poles [1] High Mast 12 Mtr. TOP A/F

mm, BOTTOM A/F 360mm, No. of Sec. No. - 1, Bottom

Thickness - 3 mm, Size of Base Plate - Dia 520 mm x

mm thick, Foundation Bolt Size M24 x 850 mm, Qty -

Nos., Suitable for mounting Fitting of Light - 6 Nos.

(Suitable foundation (Included) as per details given by

Supplying and erecting street light pole bracket

comprising main B Class GI pipe of 4.2 cm/require

outside dia. complete with suitable B Class GI

sleeve tubing of approx. 45cms.length and suitable

for 76.5mm/80mm or require size pole top having

sufficient fastners for fixing the brackets and

3 having suitable rise as per site condition as 40.00 795.88 Ea

directed and spread of 2 mtr.with suitable welded

stiffener reducer and with lock nut complete

painted with one coat of Red oxide / PU base

primer and two coats of Aluminium / PU paint.

Suitable for side entry fitting brackets of following

nos of arms. [a] Single Arm bracket 2 Mtr

Sr.No. Item Description Quantity Total Rate Unit Amount

Supplying & erecting approved make SMC press

moulded composite FRP . loop-in, loopout approx.

2mm thick box complete with Bakelite connector

strip 5way(3P+N+E),DIN rail for mounting mob &

4 hinged doors as per requirement having locking 40.00 898.90 Ea

arrangements with mounting clamp with nuts,

bolts & washers suitable for erection on pole with

cable clamps& earth bolt of following size of

box.(a) 300mm x 200mm x 100mm [deep]

Providing and erecting iron clad cable route marker

duly marked with ELE.CABLE of size 23 cm.X 12 cm.

5 Flushed with ground in cement foundation as 2.00 240.38 Ea

directed by Engineer in charge.

Supplying and erecting LED street light / Flood light

fittings with High power White LEDs wattage of

1Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free

High pressure die cast aluminum housing with

smooth finish powder coated and heat sink

extruded aluminium with diffuser and

Polycarbonate optics/ lenses with company

mark/name engraved or embossed 120 to

V,Power Factor more than 0.95, THD < 10 %, CCT

3000 K to 5700K, Uniformity ratio >0.45, Luminaire

6 efficacy> 100 lumens/watt . LED driver efficiency > 40.00 5976.17 Ea

85 %.CREE /OSRAM / PHILIPS Lumileds / NICHIA /

SEOUL/ BridgeLux (U.S.A.) make LED used for

luminaire. ( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity

between the ranges shown.) (A) Street Light (IP-

65), Surge protection - 4KV integral and 10 kv non

integral ,Light must have 440VAC line supply

protection. It should withstand 48 hours for

440VAC line supply.(iii) Above 60 to 90 watts Cat-lll

Supplying and erecting LED street light / Flood light

fittings with High power White LEDs wattage of

Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free

High pressure die cast aluminum housing with

smooth finish powder coated and heat sink

extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass

with company mark/name engraved or embossed

160 to 270 V,Power Factor more than 0.95, THD <

10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver

efficiency > 85 %.( fittings required LM-79 & LM-

80 certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (B)

Flood Light (IP-65), Surge protection -4KV integral

and ,Light must have 440VAC line supply with over-

voltage protection. (vii) above 200 to 250 watts

Sr.No. Item Description Quantity Total Rate Unit Amount

Supplying & erecting approved make Digital time

switch having lithium cell 6 years operative and

operate battery backup 1 channel day clock with

14 memory programme, suitable to operate on

240V + 5%, 16A with, floating contacts Minimum

8 switching setup time 1 minimum & LCD display. 1.00 3168.37 Ea

Also comprised permanent ON/OFF switching.

Programming switches & housed in fire proof

thermoplastic enclosure & transparent cover

erected as required with necessary connection

erected as directed.(For high mast and street lights)

Supply of Fibreglass Platform Step (A Type) Ladder -

18 FT having following specifications : It should

have large fully serrated platform 15” wide 20”

9 deep which locks ladder , Aluminium feet with 1.00 33895.60 Ea

thick rubber tread, top rail guard to serve as a

railing, two pairs of gusset support at the bottom

step and All gussets are heavy duty steel. Capacity :

300 lbs. & erecting IP 55 grade following size

section pillar fabricated from joint less M.S. Sheet

with angle iron legs made from jointless M.S. Angle

with cable clamps to be buried in ground to have

appropriate erection to work uniform until erected

with cement concrete foundation and 45 cm high

bricks work finishing with plaster etc. hinged

double door internally supported on both side,with

internal and outside looking arrangement with look

10 and keys in duplicate 35 x 35 x 5 mm M.S. Angle of 1.00 1884.66 Ea

Two Nos. one is welded and other with nut and

bolt for erecting Bakelite sheet. Painting the

Section Pillar inside and out side with three tank

powder coated paint. section pillar roof should be

without joint with water leakage proof & tested as

per IP 55 test & followed by IS 2147 of 1962 (C)

X 30 X 45 cm section pillar fabricated from

Gauge MS Sheet with angle iron legs 45 cm long

made from 35 X 35 X 5 mm thick MS angle. (For

high mast and street

Providing lights)

erecting Sheet Steel powder coated

MCB distribution board - flush / surface mounted

fitted with busbar, neutral link, earth bar and DIN

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of

MCBs.(The DBs should be used of same company

of MCB to be used) suitable for (B) three phase

incoming and single phase horizontal type

outgoing Per phase isolation type (PPI) (b) sheet

steel double door (i)4 way

Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking

capacity ICU of 25 KA. at 415 V,having normal

current rating up to 25 A to 100A. with Fixed

12 thermal & magnetic release suitable to work on 1.00 6173.12 Ea

A.C. supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in

existing 16 G.M.S. housing. ICS=100% of ICU only

Cat III (100A FP MCCB incomer)

Providing Approved make Triple Pole Metal Clad

Switch Fuse Unit 415/500 V. with HRC fuse of

suitable load and neutral link confirming to IS

(a)200 A Cat.III

Providing & erecting 415 V MCB Four Pole for

Motor & Inductive Load (C Curve) having 10KA

breaking capacity & confirms to IS :8828 in existing

box having following capacity (b)40 Amp. Cat.III

Sr.No. Item Description Quantity Total Rate Unit Amount

Providing & erecting 240 V MCB double pole switch

for lighting Load (B Curve) having 10 KA breaking

capacity & confirms to IS : 8828 in existing box having

following capacity (B) 40 Amp. Cat.III

providing and erecting Miniature circuit breaker

single pole 0.5A to 2A system and having breaking

capacity 10 KA to be erected in existing box.

confirming to IS 8828/1996 with ISI Mark Cat.III

Providing and erecting busbar chamber confirming

to IS-375 fabricated from 16 G.M.S. sheet, dust &

vermin proof having hinged door with rubber

gasket and necessary busbar supports with

Aluminium busbar having current density not more

than 0.8 Amp. / sq.mm (Rated current / cross

section area) duly wrapped with colour insulation

tape for phase sequence, three phase & neutral

each Suitable for following current capacity with

necessary painting mounted on wall or pedestal

frame of required size with necessary connections.

(B) Suitable for 200 Amp. Capacity

Supplying and erecting triple pole & neutral 440V/

500V panel mounting Aluminium Busbars with four

equal Nos. of bus having current density not more

than 0.8 Amp. / sq.mm (Rated current / cross

section area) duly wrapped with colour insulating

18 tape for phase sequence of following current 1.00 660.54 Rn.Mtr

carrying capacity, erected with necessary bus bar

supports /insulators, main cable socket to each

busbar,erected in existing cubical panel with

necessary connections. (A) Suitable for 100 Amp.

Providing & erecting High Voltage Danger Notice

19 Board sticker as per language suggested by 1.00 35.35 Ea

engineer incharge of standard size-as per IS

Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand / Solid Copper

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe at

road crossing or floor of following size of cables.

(C) 4 core 6 Sq. mm

Providing and, fixing heavy duty flange type brass

cable gland with rubber ring for PVC insulated

21 armoured cable complete with out going tails, 42.00 38.38 Ea

insulating tape etc for following size of cables. (B)

to 4 core 6 Sq. mm

Solder less crimping type Copper lugs conforming

to IS suitable for cable of following size evenly

22 crimped with high pressure tool & connected to 168.00 8.08 Ea

switchgear terminals with brass/cadmium plated

nut bolts in an approved manner. (A) 1.5/2.5 to

Supplying and erecting Flexible PVC insulated multi

strand multi core 1.1 kv grade ISI marked copper

wires of following size to be erected as directed.

(h) 2.50 Sq.mm 3 core round PVC sheathed

Sr.No. Item Description Quantity Total Rate Unit Amount

Supplying & erecting earth pit of minimum bore

dia.150mm size approved make Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 50mm having 80-200

Micron galvanising, Inner pipe dia of 25 mm having

200- 250 Micron galvanising, connection terminal

dia of 12mm with constant ohmic value

surrounded by highly conductive compound with

high charge dissipation suitable for following type

of applications with chamber and heavy duty

cover.(approved make OEM has to submit test

certificate) & having back filling compound of (B)

24 Inner chemical (CCM Compound)- Resistivity:- 0.2 • 6.00 5760.03 Ea

/ meter testing as per IEC 62561-2017, Voltage

drop:- < 1 volt at no load & dry form, Sulphar

content:- <2%(C) Back fill Compound :- Earthing

compound should be capable to retainmoisture for

long time Necessary test report must be

submitted.(c) For Electrical Installation covering

Transformer Neutrals, Lightning arrester Earthing,

A.C.Plant & Sensitive Computer System(like

Automation, SCADA) i.e independent (b)For

Electrical installation up to 11 KV in normal soil.

Length of Pipe : 2.00 mtrs Back filling Compound :1

no. Bag of 25 Kg

Providing and erecting Pipe type earthing having

150 cms.long and 2.5 cms. dia. galvanised iron pipe

25 with coupling and buch buried in specially 41.00 368.65 Ea

prepared earth pit complete with necessary 8 SWG

earth wire. - to be used for each Street Light

For using salt and charcoal / coke as required for

pipe type earthing.

Providing pair of rubber hand gloves suitable for

working on 11 KV/22 KV supply.

I / we agree to carry out the above work at __________% above the estimated rate put to tender

I / we agree to carry out the above work at __________% below the estimated rate put to tender.

Estimated amount Estimated amount

Put to tender Rs. 16,00,109.00 Put to tender Rs.

Net amount Rs.___________________ Net amount Rs.______________________

Contractor Sign With Seal Ankleshwar Nagar Palika