SPECIAL REPAIR TO BLOCK NO 291 (1 TO 4) OR MD ACCN AT GTC AREA AND PROVISION OF CERTAIN REVENUE WORKS UNDER AGE B/R II AT MIL STN KOTA

Amount

Taking down cement plaster of any description and thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Demolition/Dismantling of existing normal roof treatment, any type from RCC roof slab including lime concrete/PCC padding over roof, removing layer of bitumen under lime concrete/PCC padding, cement mortar, felt etc and cleaning the surface by hacking to receive plaster and removing demolished materials outside MD land, complete all as specified and directed.

Taking down chowkhat or frames not exc 1.50 Sqm each with shutters (with out taking off shutters from the frame), complete all as specified and directed.

Taking down chowkhat or frames exc 1.50 Sqm and not exc 4.00 Sqm each with shutters (with out taking off shutters from the frame), complete all as specified and directed.

Taking down shutters of any description exc. 1 Sqm but not exc. 2 Sqm each and removing from site complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings n.exc 15 cm thickness (below or above GL), complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete as specified and directed.

Demolition of cement concrete (reinforced) such as roofs, floors (other than ground floors), beams, stair cases, landing, chhajjas and other similar works and removing rubbish from premises, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

Dismantling floor, hearth or wall tiling/ terrazzo including cement mortar bedding (but not backing), removing tiles and rubbish off the premises, complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work & precast concrete articles, complete all as specified and directed.

M&L for PCC 1:2:4 mix type B-0 (Using 12.5 mm graded crushed stone agg) for roof padding, leveling course to receive floor finishes etc, complete all as specified and directed.

M&L brushing neat cement slurry with 3.00 kg cement per Sqm, complete all as specified and directed.

M&L for applying 15 mm thick screed in CM 1:4 on roof slabs with using liquid water proofing compound as per manufacturer's instructions, complete all as specified and directed. (Liquid WPC shall be measured and paid separately).

M&L for cleaning of roof slab including picking, sweeping clean and washing down with water to remove dust, dirt etc and Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to IS 3384 @ of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of cold applied bituminous primer conforming to IS:3384 @ 0.40 Kg/Sqm.

Item 15.00 Contd........ (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm (minimum) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimney/other vertical surfaces and polymeric membrane inserted in groove and sealed with paving bitumen. (v) Cost of above aspects is deemed to be included in quoted rates.

M&L for cleaning of walls and floor of sunken portions including picking, sweeping clean and washing down with water to remove dust, dirt etc and Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to IS: 3384 @ 0.40 Kg/Sqm, torching overlaps with a propane or a butane gas torch with an overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold applied bituminous primer all as per manufacturer’s instructions, complete all as directed. Note: (i) The waterproofing treatment shall be got carried out through the manufacturer or their authorized applicators only.

Supply only approved liquid water proofing compound, complete all as specified and directed.

Taking down shutters of any description exc. 1 Sqm but not exc. 2 Sqm each and refixing in same position complete all as specified and directed.

Taking down shutters of any description exc. 1 Sqm but not exc. 2 Sqm each and refixing in other position complete all as specified and directed.

S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium window and ventilator shutters, sliding type without sash bars, aluminium sections weighing not less than 0.32 kg/m including necessary joining cleats, glazing clips, rubber packing, screws, anodised aluminium fittings such as suitable handle (1 No.), slide lock device etc, complete all as specified and directed.

S&F in replacement of top rail/bottom rail/lock rail/stiles of aluminium door/window/ventilator shutter, repair/adjustment including necessary materials such as aluminium sections of required size, cleats, rubber beading, handles etc including taking down and refixing of shutters, complete all as specified and directed.

Supply only 5.00 mm thick figured glass, pin head type, cut to size as required at site, complete all as specified and directed. (Note: cost of fixing of glass shall be deemed included in the unit rates of aluminium shutters.)

Supply only stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm, complete all as specified and directed. (Note: cost of fixing of wire cloth shall be deemed included in the unit rates of aluminium shutters)

S&F 35mm thick factory made IInd Class Hard wood (Hollock) paneled door shutters single panel with lock rail and panel of 9mm B.W.P. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to IS-710 or 12mm thick particle board veneered with commercial veneering on both faces. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S&F 35mm thick factory made IInd Class Hard wood (Hollock) glazed and skeleton, open rebated, prepared to receive glass, gauge etc, without sash bars, edges of framing plain, chamfered and rounded, fitted with cut and mitered beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S&F solid PVC door frame of size 50mmx 47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as specified and directed.

Dismantling boarding of any description fixed in any position with nails/screws, complete all as specified and directed.

M&L for 18/19 mm thick prelaminated particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work, complete all as specified and directed.

M&L for 18/19 mm thick block boards, grade 1 quality, exterior grade, commercial type, fixed with screws to timber frame-work with and including 12mm thick teak wood leaping alround complete all as specified and directed.

M&L for 18/19 mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in CB shutter, pelmet including 12mm thick teak wood leaping and necessary rebating for double shutter where required incl polishing to leaping, complete all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section 150 mm long and fixed, ISI marked complete all as specified and directed.

S&F aluminium handles, cast type, anodised 150 mm size, ISI marked complete all as specified and directed.

S&F 150 mm size, mild steel pressed handles, oval type, stove enamelled black, ISI marked complete all as specified and directed.

S&F 100 mm size mild steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws, complete all as specified and directed.

S&F of 300 mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

S&F 300 mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed.

S&F 100 mm hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed.

S&F 150 mm hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed.

S&F floor door stopper of brass body and tongue, with hard drawn steel spring, fixed in floor, overall length of cover plate 150 mm, complete all as specified and directed.

S&F in renewal of 'D' type tubular towel rail 60 cm long, brass chromium plated, 20 mm dia, complete fixed with stainless steel screws, complete all as specified and directed.

S&F galvanised mild steel wire cloth, 0.56 mm nominal bore of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S&F in renewal of galvanised mild steel wire cloth, 0.56 mm nominal bore of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S&F brass cupboard knobs 40 mm dia, bright polished, fancy type, fixed with brass screws, complete all as specified and directed.

S&F 300 mm size corner type toughened glass shelf of 6 mm thick glass and CP guards of approved quality and fixed to wall with SS screws including dash fastener etc, complete all as specified and directed.

S&F continuous piano hinges, made of stainless steel, 30 mm width of flaps when open, complete all as specified and directed.

Dismantling timber in fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section as in framed work complete all as specified and directed.

M & L for 2nd class hardwood plain fillets square, rectangular or triangular in section in bull nosed, splayed, chamfered or rounded on one edge or face wrought sectional area exc 3 Sqcm but not exc 6 Sqcm & fixed with nails complete all as specified and directed.

M & L for 2nd class hardwood plain fillets square, rectangular or triangular in section in bull nosed, splayed, chamfered or rounded on one edge or face wrought sectional area not exc 3 Sqcm & fixed with nails complete all as specified and directed.

M & L for 2nd class hardwood plain fillets square, rectangular or triangular in section in clean sawn, secured with nails or brads, wrought sectional area exc 13 Sqcm but not exc 25 Sqcm & fixed with nails complete all as specified and directed.

Resecuring or easing and adjusting without taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each, complete all as specified and directed.

M & L in renewal of GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste (if repair in patches not exc 5 sqm each, including taking down old and jointing new to old as required) complete all as specified and directed.

S&F magnetic ball catcher, 40 mm size, fixed with screws, complete all as specified and directed.

S & F of unplasticised PVC pipes of pressure rating 10 kgf/cm2 and including all its fittings like bend, tee etc fixed to walls, ceilings or in floors etc., any type of pipe size 50mm bore complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggreate), 75 mm thick as in plinth protection/Path/PCC paving etc including finishing the surface even & smooth without using extra cement, with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where dirtected and providing 6 mm wide joints throughout the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three parts of fine sand by weight), complete all as specified & directed.

M&L 75 mm thick PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in sub base of floors etc, complete all as specified and directed.

M&L 100 mm thick PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in sub base of floors etc, complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size made with grey cement and pigment, confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, laid over and including 25 mm thick sand cushioning, complete all as specified and directed.

M&L precast (factory casted) cement concrete kerb stone casted in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate with plain or interlocking joints (as directed) including making groove in ground of desired dimension, including weathering, slightly rounded or chamfered angles, placing in position, set and jointed in CM 1:4, making good distrubed surface of ground complete all as specified and directed.

M&L PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in foundation, mass concreting etc, complete all as specified and directed.

M&L PCC 1:2:4 type B-2, using 40 mm graded stone aggregate, as in foundation mass concreting etc, complete all as specified and directed.

M&L brick work with old size pulverized fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan exc 6 m mean radius, built in CM 1:6, complete all as specified and directed.

M&L for brick work with pulverised fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan to any radius in half brick walls built in cement mortar 1:4, complete all as specified and directed.

M&L sand stone walling of random rubble, uncoursed well bonded, bedded and solidly hearted, built in Cement Mortar 1:6, complete all as specified and directed.

M&L for walling of random rubble except stone i.e. using old serviceable stone obtained from demolition under serial item No. 11.00 (here-in-before) uncoursed well bonded, bedded & solidly hearted built in cement mortar 1:6 complete all as specified and directed.

Extra over for stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses, with maximum depression on face from straight edge held against the dressed surface not exceeding 20 mm; to block in course masonry (Lime or sand stone), complete all as specified and directed.

Form work (for fair finished surfaces) to to fins, louvers, fascia/chajjas etc., complete all as specified and directed.

Formwork (rough finished surfaces) to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, complete all as specified and directed.

M&L for RCC 1:1.5:3 type A-1 (using 20 mm graded stone aggregate), as in chhajjas, facias etc, complete all as specified and directed.

M&L for providing cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles, throating and including neccesary formwork complete all as specified and directed.

M&L PCC 1:2:4 type B-2 using 40 mm graded stone aggregate as in surface channel and drains, finished even and smooth without using extra cement complete all as specified and directed.

M&L for providing precast cement concrete 1:2:4, type B-1 using 20 mm graded stone aggregate as in landings, cover slabs (for manholes etc), chajjas, water troughs, mangers, shelves and similar articles with plain faces including necessary formwork, set in CM 1:4, complete all as specified and directed.

M&L 450 mm dia Reinforced concrete pipes, class NP2, laid in trenches and jointed complete with collars, complete all as specified and directed.

M&L PCC 1:4:8, type D-2 using 40 mm graded stone aggregate, as in concrete bed to drain pipes including packing under and haunching against the sides of 450 mm dia pipe, after they are laid and tested, complete all as specified and directed.

M&L for mild steel TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm bore or securing with clips, complete all as specified and directed.

S&F mild steel framed work as in grills, grating etc. with end of bars shouldered and/or riveted, or forged into spikes: framed guard bars: barred iron doors: ladders: frame balusters: walk ways: railing: frame work of water tanks and similar works conforming to Fe-290 Grade-E-165, complete all as specified and directed.

M&L mild Steel work in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe 410-W (Gde - E-250) quality-A, complete all as specified and directed.

S&F mild steel tube ERW or induction butt welded conforming to IS-1161-1979 St-240 medium class as in post/pole and struts etc with connecting plate, base plate etc including cutting to shape, drilling hole, bolting or riveting etc complete all as specified and directed.

S&F mild steel work with hollow section square or rectangular section as in tubular trusses, purlins including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St-240 including notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts including rivets or nuts and bolts, providing and fixing cleats, fish plates, gusset plates etc and also for wedging, plumbing, turning up & fixing complete all as specified and directed.

S&F in renewal of welded steel wire fabric supplied and fixed complete to wood or steel members, weight per Sqm not exceeding 4.00 kg, complete all as specified and directed.

S&F prepainted galvalume aluminum zinc coating GI based Plain steel sheet crimped eaves and steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S&F prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and directed.

Dismantling fencing wire of any type (barbed wire) with & including concertina coil of existing boundary wall complete all as specified and directed.

Dismantling angle iron 'Y' shape of existing boundary wall complete all as specified and directed.

Fixing only concertina coil (retrived from item No 85.00 here-in-before) with necessary scaffolding on existing boundary wall (approx height 10 feet) and including provision of binding wire, complete all as specified and directed.

Fixing only angle iron 'Y' shape(retrived from item No 86.00 here-in-before) with necessary scaffolding on existing boundary wall (approx height 8 feet) complete all as specified and directed.

S & F of concertina coils dia of coil exc 50cm after fixing with necessary scaffolding on existing boundary wall (approx height 10 feet) and including provision of binding wire, complete all as specified and directed.

S & F for galvanised, 2 strand steel barbed wire 2.24 mm dia, barbed with 2.00 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rail, straining bolts, incl securing or tying at crossing with and provision of galvanised MS wire, staples or steel pins etc, complete all as specified and directed. (each line wire to be measured).

Dismantling loose concrete cover of RCC columns, beams and the like, area not exc 2.0 Sqm each, roughening and cleaning of concrete surfaces with steel wire brushes, washed with water and allowed to dry including dusting of steel reinforcement, providing welded mild steel wire fabric of mesh size 75 x 75 mm and 2 mm nominal dia of wire as reinforcement to concrete surfaces, applying adhesive/admixture over steel mesh and providing ordinary portland cement 53 grade and 2 parts of sand mixed with admixture at the rate as per manufacturer's instructions with a pressure of 2 to 2.5 Kg/Sqcm by guniting machine including necessary padding, steel scaffolding and shuttering for working platform/formwork etc, complete all as specified and directed.

All as per item 91.00 (here-in -before) but area exc 2.0 Sqm each, complete all as specified and directed.

S&F Anodised aluminium snap grid frame work for false ceiling, size of grid 605x605 mm, including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long, complete all as specified and directed.

S&F 40mm thick PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably placed as in false ceiling grid of size 605x605 mm made of Aluminium/G.I./M.S. as per specification, complete all as specified and directed.

S&F micro perforated square edge and attractive finish mineral fibre (sand micro) of nominal size 595x595x15 mm thick having building attribute as in false ceiling, fixed with and including grid of size 600x600mm having main frame of aluminium T of size 35x25x0.70 mm thick, cross aluminium T of size 25x35x0.7 mm thick, the grid shall be suitable for mineral fibre tiles and hanging from soffits of existing RCC roof slab with using connecting clips, complete all as per manufacturer’s instructions, specified and directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, on vertical surfaces etc, set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick rendering in CM 1:4, complete all as specified and directed.

M&L Glazed ceramic coloured tiles on vertical surfaces 350x 250x7 mm/450X350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick rendering in CM 1:4, complete all as specified and directed.

M&L for machine cut kota stone slab as in flooring 17 to 22 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B-0 (using 12.50 mm graded stone aggregate) as in flooring/sub base finished rough to receive floor finishes/screed complete all as specified and directed.

M&L for machine cut kota stone slab as in skirting, dado, risers etc, 20 to 25 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing, laid over and including rendering 10 mm thick backing in CM 1:4, complete all as specified and directed.

M&L granite slab 18-20 mm thick, table rubbed and polished in cooking platform, jambs, cills, pillars, tread, risers, platform for WHB etc including bull nosing to exposed outer edges, set in CM 1:4 bedding and pointing with white cement mixed with pigment, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for 25mm dia cutting holes in kota stone for gas connection, complete all as specified and directed.

M&L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:4, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 5 mm thick on fair faces of ceiling in cement mortar 1:3 including finishing the surface even and smooth, complete all as specified and directed.

M&L for preparing new previously untreated plastered surfaces of walls and applying two coats of modified exterior emulsion paint over & including a coat of primer, complete all as specified and directed.

M&L for applying three coats of white wash on ceiling including preparation of new or previously untreated surfaces, complete all as specified and directed.

M&L for applying two coats of white wash after preparation of old previously treated plastered surfaces of ceiling, complete all as specified and directed.

M&L complete removal of existing treatment from previously treated surfaces of walls and applying 3 mm thick Wall care putty as per manufacturer's instructions and over it applying two coats of distemper oil emulsion over a coat of primer, complete all as specified and directed.

M&L complete removal of existing treatment from previously treated surfaces of walls and applying two coats of modified acrylic emulsion paint over a coat of suitable primer, complete all as specified and directed.

M&L for applying 2 coats of synthetic enamel paint over and including a coat of pink primer on wooden surfaces, exceeding 10 cm in width or girth, incl preparation of the new surfaces complete all as specified and directed.

M&L for preparation of old painted wooden surfaces/wood based surfaces of any description not otherwise described, not exc 10 cm in width or girth when unconnected with other painting or when painted in different tint & applying 2 coats of synthetic enamel paint over and including a coat of pink primer complete all as specified and directed.

M&L for preparing new steel surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over & including one coat of red oxide zinc chrome primer, complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

S&F in renewal of stainless steel tubular curtain rods, 25 mm dia, with fixing brackets and one pair of decorative end caps etc, complete all as specified and directed.

S&F in renewal of PVC connection 600 mm long suitable for 15 mm GI pipe with two PTMT nuts and rubber washers complete all as specified and directed.

S&F in renewal of PVC connection 450 mm long suitable for 15 mm GI pipe with two PTMT nuts and rubber washers complete all as specified and directed.

S&F in renewal of 20 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe, complete all as specified and directed.

S&F in renewal of bib taps, cast copper alloy, with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F in renewal of 15 mm bore stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union complete all as specified and directed.

S&F in renewal of stop valves, fancy type, chromium plated brass with long shank and cup (Concealed type), screwed down, high pressure, both ends screwed to iron pipe or for union, dia of pipe 15 mm, complete all as specified and directed.

S&F in renewal of 20 mm bore stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union complete all as specified and directed.

S&F in renewal of shower rose, brass chromium plated, 125 mm size with swivel joint, screwed to iron pipe or for union of 15 mm dia, complete all as specified and directed.

S&F in renewal of vitreous china wash hand basin white with flat back of size 550x400 mm, excluding chain and plug, taps and porcelain stopper but incl PVC waste pipe of 32 mm bore, one pair of 600 mm long cast iron brackets, complete all as specified and directed.

S&F in renewal of pillar taps, cast copper alloy, with capston heads, chromium plated, fancy type, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed.

S&F in renewal factory made pressed steel cupboard shutters alongwith frame, frame made of 1.25 mm thick PBI sheet and shutter made of 1.00 mm thick PBI sheet with 6 Nos 3.15 mm thick and 100 mm long steel hinges per shutter, godrej pattern locking arrangement with 12 mm dia vertical rod and lock with duplicate key & chrome finish handle, duly spray painted in factory with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer, complete with fastener, hold fast etc as required at site, complete all as specified and directed. (Total width including frame shall be measured for payment purpose).

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 15 mm bore pipes complete all as specified and directed.

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 20 mm bore pipes complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) for 15 mm dia pipes with and including all new fittings complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) for 20 mm dia pipes with and including all new fittings complete all as specified and directed.

Supply, fixing, laying & testing 15 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed.

Supply, fixing, laying & testing 20 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed.

S&F in renewal of vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest incl providing lime concrete bedding and connecting to flusing cistern, complete all as specified and directed.

S&F in renewal of PVC dual flush cistern 10 Ltr capacity, valveless, syphonic action type, low level, white, with inlet, ball valve, float and handle & including brackets and superior quality PVC 32 mm bore flush pipe, complete all as specified and directed.

S&F in renewal of sink with draining board made of stainless steel 1mm thick with plugs, washers and waste coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets of suitable angle iron, 32 mm dia superior quality PVC waste pipe and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F in renewal of stainless steel kitchen plate rack of size 910x780x250 mm, made of 0.80 mm thick stainless steel sheet with partition for small /large plates and fixed in position, design and pattern as approved by the GE, complete all as specified and directed.

S&F in renewal of 75 mm bore PVC (SWR) floor trap with CP grating including jointing to waste pipe and fixed in cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate), complete all as specified and directed.

Dismantling existing water storage tank of any description of capacity exc. 250 Ltr but n.exc. 500 Ltr, complete all as specified and directed.

S&F in position rotational moulded polyethylene water storage tanks 500 lts capacity (cylinderical vertical with closed top) hoisted and fixed in position, complete all as specified in SSR Part I and as directed.

S&F PVC (SWR) pipe 75 mm bore, single socketed, in any length with rubber ring joints and fixed to wall, ceiling or floors and including dismantling of old u/s cast iron/existing pipes alongwith fittings and accessories complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and fixed to wall, ceiling or floors and including dismantling of old u/s cast iron/existing pipes alongwith fittings and accessories complete all as specified and directed.

S&F PVC (SWR) pipe 75 mm bore, single socketed, in any length with rubber ring joints laid in trenches or in floors and including dismantling of old u/s cast iron/existing pipes alongwith fittings and accessories complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints laid in trenches or in floors and including dismantling of old u/s cast iron/existing pipes alongwith fittings and accessories complete all as specified and directed.

S&F in renewal of PVC (SWR) bend 75 mm bore, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F in renewal of PVC (SWR) bend 110 mm bore, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F in renewal of PVC (SWR) 75 mm bore single Junction 'T', equal or unequal with oval access door, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

S&F in renewal of PVC (SWR) 110 mm bore single Junction 'T', equal or unequal with oval access door, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

S&F stack clamps made out of 50x5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, bore of pipe 100/110 mm, complete all as specified and directed.

S&F stack clamps made out of 50x5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, bore of pipe 75/80 mm, complete all as specified and directed.

S&F in renewal of PTMT alloy toilet cabinet with mirror of overall size 350x450 mm and fixed to wall complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls and applying 3 mm thick Wall care putty as per manufacturer's instructions and over it applying two coats of distemper oil emulsion over a coat of primer, complete all as specified and directed.

S&F 16 to 20 mm dia MS screw bolts (Purpose made ) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washer and one hexagonal or square nut, length of bolt exc 5 cm but not exc 10 cm, complete all as specified and directed.

Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil, complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m deep for foundation etc or for shafts, column footings or for laying cables etc not exc 10 Sqm on plan and getting out in soft/loose soil, complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and exc 1.5m but not exc 3.0m in depth for foundation etc or for shafts, column footings or for laying cables etc not exc 10 Sqm on plan and getting out in soft/loose soil, complete all as specified and directed.

Excavation in post holes (or similar holes) Each n exc 0.50 Cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm, watering and removing surplus soil to a distance of n exc 50m and making good surface in soft/loose soil, complete all as specified and directed.

Returning filling in excavated soil including spreading, levelling, watering and well ramming in layers not exc 25 Cm, complete all as specified and directed.

Removing excavated materials (soil) not exc 50 m distance and depositing where directed at a level not exc 1.5 m above the starting point, complete all as specified and directed.

M&L hardcore (broken stone) of gauge not exc 63 mm, deposited spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for reuse or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Dismantling unserviceable main switch/DBs incl wooden board and deposit to MES store yard including making good disturbed surface of wall complete all as specified and directed.

Taking down sub main wiring /XLPE cable of any size/capacity complete all as specified and making good disturbed sufaces to match with the existing surface, complete all as specified and directed.

M&L for Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface including providing wooden rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover and making good disturbed surfaces, complete all as specified and directed for the following: - One light/ceiling fan/exhaust fan/bell buzzer point controlled by one, one way switch of 5/6 Amps.

All as per item No 165.00 (here-in-above) but one 5 Pin, 5/6 amps socket outlet point on independent board, controlled by one, one way 5/6 Amp switch.

All as per item No 165.00 (here-in-above) but one 5 Pin, 5/6 amps socket outlet point on same board, controlled by one, one way 5/6 Amp switch.

All as per item No 165.00 (here-in-above) but one light point controlled by two, two way switch of 5/6 Amps.

M&L Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 2.5 Sqmm, with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable FRLS of size 2.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface for one socket outlet 15 amp on independent board including providing wooden rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover and making good disturbed surface, complete all as specified and directed.

S&F switch piano flush type 5/6 Amps, 230 volts, single pole, one way, ISI marked, complete all as specified & directed.

S&F switch piano flush type 5/6 Amps, 230 volts, single pole, Two way, ISI marked, complete all as specified & directed.

Supply and fixing switch socket combination, 5/6 and 15/16 Amps, 230 volt, multi pin, flush type universal, complete all as specified and directed.

Supply and fixing socket outlet, 5/6 Amps, 230 volt, five pin, flush type universal, complete all as specified and directed.

S&F in renewal of stepped type electronic fan regulator, flush type, 230 volts AC, single pole, humming free, fixed on the existing phenolic laminated sheet, complete all as specified and directed.

S&F ceiling rose surface type PVC/Polycarbonate isolated body, 65x 50mm, 3 terminals, complete all as specified & directed.

S&F PVC/polycarbonate lamp holder, angular/batten type with back plate, ISI marked complete all as specified & directed.

S&F bell push AC, SP, 240 volts, flush type, 5 Amp/ 6 Amp, complete all as specified and directed.

S&F in renewal of call bell, AC, 230 volts, single pole, ISI marked complete all as specified & directed.

S&F of wall mounted LED Tube light fittings, batten type with bipin holders, powder coated steel with & including retrofit 18 watt LED tube, internally prewired, complete all as specified and directed.

S&F of wall mounted LED Tube light fittings, batten type with integrated LED tube, powder coated steel with & including retrofit 11 watt LED tube, internally prewired, complete all as specified and directed.

S&F in renewal of LED building security light fitting, 25 watt, pressure die cast aluminium housing with IP 66 deg of protection, complete with & including 0.55 m long street light bracket made of 32 mm bore GI light grade tubing including necessary clamps, nuts, bolts, washers etc, complete all as specified and directed.

S&F LED light fitting 30/36 Watt, 230 Volt AC, recessed mounting mirror optic luminiare with paralite louver complete, suitable for false/grid ceiling, complete with electronic driver, connector block and all accessories, duly prewired, including connecting up with three core twisted flexible copper conductor cable of size 14/.0060, complete all as specified and directed.

S&F MCB, 6 to 32 Amps, Single Pole, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S&F MCB, 6 to 32 Amps, Single Pole & Neutral, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S & F, MCB TPN 63 Amps, 415 volts, four pole, B-curve, rupturing capacity 16KA conforming to IS-8828-1996, IEC-60898, complete, all as specified & directed by Engineer-in- charge.

S & F factory made MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, earth bar and Din rail, 240 Volts SPN with 8 ways, Double door, complete all as specified and directed. Note for items of MCB DB - (1) The unit rate includes for cutting the brick walls to accommodate DB to make flush to wall. (2) The unit rate includes for making good the disturbed surfaces including finishes to match with the adjoining surface.

S & F factory made MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, IP-43-IK09 protection grade, earth bar and Din rail, 415 Volts TPN with 4 ways, Double door, complete all as specified and directed.

S & F factory made MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, IP-43-IK09 protection grade, earth bar and Din rail, 415 Volts TPN with 8 ways, Double door, complete all as specified and directed.

S&F SPN enclosure with a two pin and earth plug and socket, complete with & including one double pole MCB of 20 amps, 230 Volts AC, complete all as specified and directed.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed FRLS multistranded copper conductor cable of size 6 Sqmm LT, 1100 volts grade, drawn through and including 20 mm dia PVC non metallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded FRLS copper conductor cable green colour as earth continuity conductor, complete all as specified & as directed. Note :- Two runs of cable one run of earth wire and one run of PVC non metallic conduit of 20mm dia shall be measured as one run length. Cable required for connection to DBs shall deemed to be included and shall not be measured separately. Earth wire shall run inside the PVC conduit.

M&L for Earthing with galvanized steel earth plate electrode of size 600 mm x 600mm x 6.0 mm, buried directly in ground (earth plate not less than 2.25 Mtr below normal ground level) connected to galvanized iron earth wire of 4 dia by means of bolts, nuts, check nuts and washers of galvanized iron including 15 mm bore light grade GI tubing for protection of earth wire, MS sheet metal funnel with wire mesh, watering pipe medium grade 20 mm bore, charcoal or coke and common salt in alternative layer of 15 Cm compacted thickness all around the electrode with concrete earth pit of PCC 1:3:6 type 75 mm thick precast RCC (1:2:4) type B1 pit cover reinfored with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar and necessary excavation, earth work, in soft/loose soil and disposal of spolis to a distance not exc 50 Mtr and necessary connection and testing complete all as shown in electrical plate No. 5 and including dismantling of old u/s earthing complete all as specified and directed. Notes: - (a) Irrespective of whatever is shown in plate No 5 of SSR, earth pit shall be casted in PCC (1:3:6) type C-1 and precast cover of RCC (1:2:4) type B-1 with suitable handle. (b) Item includes the cost of GI pipe for protection of earth wire and earth wire upto 7.5 m. Any variation below or above shall be measured and paid for separately under relevant item of this Sch ‘A’.

Supplying and erecting in true vertical position steel tubular swaged pole, 9 metres long, type 410 SP-31, complete with cast iron base plate, pole cap, finial taper plug, bolts, nuts, washers etc including necessary earth work and excavation, PCC in foundation 1:3:6 type C2, using 40 mm graded stone aggregate and PCC 1:2:4 type B2, using 40 mm graded stone aggregate as in plinth block, disposal of surplus soil to a distance not exceeding 50 m,painting two coats of aluminium paint over one coat of red oxide primer including 3 nos band/straps with red post office box colour (300mm wide each) synthetic enameled paint at a distance 300mm from plinth; block and marking pole nos with black synthetic enameled paint including tarring one coat on steel surface embedded in concrete complete all as specified and directed. Note :- Cost of excavation, earth work & PCC as in foundation and coping, painting to pole etc are deemed to be included in the this item.

S & F new generation energy saving & environmental friendly long life versatile pressure die-cast aluminium IP-66 roadway luminaire with high power LED as light source and electronic driver of capacity 70 Watt & including not less that 1.80 m long street light bracket made of 32 mm bore or suitable as per hole of light fitting bent to 120 degree shape, GI light grade tubing including necessary clamps, nuts, bolts, washers etc, complete all as specified and directed.

S & F Junction box made out of 2 mm thick CRCA sheet of size 250mmx250mmx150mm with hinged door and locking arrangement & including aluminium bus bar of size 25x3mm three phase & neutral fixed on insulator, including one No MCB SP 6 Amps & painting the box with two coats of synthetic enamel paint over a coat of red oxide primer all as specified and as directed.

Supply and fix PVC insulated unsheathed copper conductor cable 1.5 sqmm 3 runs from street light fitting to junction box on pole of 9 meters and making necessary connection both at junction box and street light fittings and fixing accessories complete all as directed. Note:- (i) Three runs of cable shall be measured and paid as one length only. (ii) Suitable size PVC conduit shall be deemed inclusive in quoted cost.

Supply and fixing of street light timer distribution boards (Astronomical type) 20 Amp 3 pole, 230 Volts as suitable for out door operation & including astronomical time switch infra red sensor for automatic operation of lights as per seasonal variation of day lights, relay, MCB complete all as specified and directed.

S&F in renewal of metal body propeller type ventilating fans (Exhaust fan), 240 volts AC, 300 mm sweep with louver shutter complete including connecting with and including PVC insulated three core 23/.0076 copper conductor cable, rubber insulated from ceiling rose to exhaust fan motor and writing MES No with black synthetic enamel paint 2.0 cm high complete all as specified and directed.

S&F in renewal of ceiling fans of 1200 mm sweep including all accessories such as down rod, canopy, blade set comprising of three blades, hanging arrangement with rubber block, nuts, bolts, washers, split pins, capacitor etc complete with and including PVC insulated twisted twin core 23/0.0076 copper conductor flexible rubber insulated cable of required length from connector/ceiling rose to fan motor including testing, commissioning and painting with black synthetic enameled paints MES number upto 2.5 cm high, complete all as specified and directed.

Supplying, laying, jointing testing and commisioning XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with multistranded aluminum conductors, 1100 Volt grade of cross-sectional area 25 Sqmm, 3.5 core, laid in trenches / ducts / encased in GI pipe / fixed to pole/wall, complete all as specified and directed.

Supplying, laying, jointing testing and commisioning XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with multistranded aluminum conductors, 1100 Volt grade of cross-sectional area 10 Sqmm, 2 core, laid in trenches / ducts / encased in GI pipe / fixed to pole/wall, complete all as specified and directed.

M&L dry clean Sand filling in trenches around underground cables for earth cushion, complete all as specified and directed. Note: - Depth of sand shall be measured after punning.

Supplying and laying pulverized fuel Ash-lime bricks (Fly ash bricks - non modular size), laid flat adjoining each other as in protection to UG cables, complete all as specified and directed.

M&L of 40 mm bore Steel water tubing, light grade, galvanised, with all fitting, laid in trenches/fixed to walls/poles etc as protection to cables, with and including necessary MS clamps, nuts botls, washers etc required for fixing, complete all as specified and directed.

M&L in renewal of 40 mm bore Steel water tubing, light grade, galvanised, with all fitting, laid in trenches/fixed to walls/poles etc as protection to cables, with and including necessary MS clamps, nuts botls, washers etc required for fixing, complete all as specified and directed.

K B Enterprises

Ganesh Contruction

M/s Prem Associates

L P Singh and Co.

SK Guha and co

ANNAPURNA ENTERPRISES

M/S MOHINI ENTERPRISES

S AND A ENGINEERS CONSTRUCTION CO