SJMMSVY ICONIC Road

Name of Work : CONSTRUCTION OF ICONIC ROAD 2.0 FROM BUS STATION TO MAHARANA PRATAP CIRCLE IN DEESA MUNICIPALITY AREA

Bill of Quantity

Sr No Item Description Unit Qty Rate Amount in Rs.

Dismantling Tiled Or Stone Floors Laid In Mortar Including Stacking Of Serviceable Material

And Disposal Of Uservicalble Material With All Lead And Lifts.

Demolition & Disposal Of Unservisable Material With All Lead And Lift For Unreinforeced

Demolition Of Brick Work & Stone Masonry Including Stacking Of Serviceable Materials And

Disposal Of Unserviceable Materials With All Lead And Lift (1) In Cement Mortar.

Dismentling steel work including distempering and stacking the materials with all lead and

Demolition Including Stacking Of Serviceable Materials And Disposal Of Unserviceable

Materials With All Lead And Lift. (I) R.C.C Work.

Earthwork in cuting in all sorts of soil and soft murrum including conveying and spreading

6 the stuff, embankment as and where directed up to any lead from the end of the cutting with Cmt 1,193.50 ₹ 134.13 ₹

all required lead and lift.

Conveyance Charge Of Earth, Lime, Murrum, Building Rubbish, Manure, Garbage, Sludge,

Excavated Rock, Fly Ash, Aggregates Of Any Kind Executed Outside The Road Site. Rate

Also Includes Spreading & Levelling Etc Complete. Internal Conveyance Above 50 Mt Done

Within The Work Site Is Not Payable. e) Lead From 4 Km to 5 Km.

Providing and fixing pre-cast concrete kerb stone of gray cement based concrete block

30cm length,30cm height and 15cm thick of M250 grade concret as per approved design

and including excavation for fixing in proper line and level,filling the joint with C:M 1:3

(1cement:3fine sand) etc complete.

Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete block 60mm

thick with grade of concrete M300 pnumatic compressed / vibrated mechanically and as per

9 approved design Confirming to IS 15658 : 2006 including 35 mm Sand layer for levelling Smt 6,612.00 ₹ 706.90 ₹

and filling the joint with sand in proper line and level as per guidlines of IRC : SP 63-2018

Providing and laying precast concrete grass paver blocks of approved make, size (typically

400mm x 400mm x 80mm or as specified), and thickness, manufactured using M30 grade

concrete with approved pigment, compacted by vibro-pressing for uniform strength and

durability. Blocks to be laid over a compacted sub-base and 50mm thick sand bed, including

leveling, joint filling with soil/sand mix, and turf/grass plantation in voids, complete in all

respects as per drawings, specifications, and instructions of Engineer-in-Charge.

Providing and laying cement concrete flooring 1:2:4 (1- cement : 2-coarse sand : 4-graded

11 stone aggregate 20mm nominal size) laid in one layer and finished with a floating coat of Smt 355.00 ₹ 349.10 ₹

neat cement. (B) 50mm thick.

Excavation For Foundation Upto 1.5 M Depth Including Sorting Out And Stacking Of Useful

Materials And Disposing Off The Excavated Stuff Upto 50 Meter Lead.(A) Loose Or Soft Soil

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of

13 useful materials and disposing off the excavated stuff upto 50 Meter lead.(A) Loose or soft Cmt 1,350.00 ₹ 136.30 ₹

Excavation for foundation for depth from 3.0 m to 5.0 m including sorting out and stacking of

14 useful materials and disposing off the excavated stuff upto 50 Meter lead.(A) Loose or soft Cmt 900.00 ₹ 149.65 ₹

Filling Available Excavated Earth (Excluding Rock) In Trenches. Plinth, Sides Of

15 Foundations Etc. In Layers Not Exceeding 20 Cm. In Depth Consolidating Each Disposited Cmt 2,041.00 ₹ 136.92 ₹

Layer By Ramming And Watering.

Providing and laying cement concrete 1:4:8 (1- Cement : 4-Coarse sand : 8- Graded Brick

16 bats aggregate 40mm normal size) and curing complete excluding cost of formwork in (A) Cmt 1,026.50 ₹ 2,717.81 ₹

Foundation and Plinth

Supplying and filling in foundation and plinth with RUBBLE including filling voids with sand

and watering etc.complete.

Providing and laying controlled cement concrete M.250 and curing complete Including the

18 cost of formwork and excluding reinforcement for reinforced concrete work in (A) Cmt 100.00 ₹ 4,575.59 ₹

Foundations, footings, Base of columns and Mass concrete.

Providing and laying controlled cement concrete M.250 and curing complete including the

19 cost of formwork and excluding reinforcement for reinforced concrete work in (D) Columns, Cmt 22.00 ₹ 6,296.72 ₹

Pillars posts and struts, upto floor two level.

Providing And Laying Controlled Cement Concrete M.250 And Curing Complete Including

The Cost Of Formwork And Excluding Reinforcement For Reinforced Concrete Work In (C)

Slabs,Landing,Shelves,Balconies, Lintels, Beams, Girders And Cantilever Upto Floor Two

Providing Tmt Bar Fe 500D Reinforcement For R.C.C. Work Including Bending, Binding And

Placing In Position Complete Upto Floor Two Level

Boring holes 3.5 m deep in ordinary soil (for cast in situ piles) and getting out the soil and

22 disposal of the surplus excavated soil as directed within a lead of 50 Meter for following Each 194.00 ₹ 1,560.45 ₹

diameter of pipes.(iii) 300 mm

Brick Work Using Common Burnt Clay Building Bricks Having Crushing Strength Not Less

23 Than 35 Kg./Sq.Cm. In Foundation And Plinth In Cement Mortar 1:5. (1- Cement : 5 -Fine Smt 13.00 ₹ 4,244.85 ₹

Brick Work Using Common Burnt Clay Building Bricks Having Crushing Strength Not Less

Than 35 Kg./Sq.Cm. In Foundation And Plinth In Cement Mortar 1:5. (1- Cement : 5 -Fine

Sand)(B) Conventional Extra For Brick Work In Superstructure Above Plinth Level Up To

Floor Two Level (B) Conventional

Providing 20 Mm Thick Double Coat Mala Cement Plaster On Exterior Brick / Concrete

Work For Plastering Comprising Of Base Coat Of 12 Mm Thick Cement Plaster In Cement

25 Mortar (1 Cement : 4 Coarse Sand) In Rough Finishing And 8 Mm Thick Top Coat Of Smt 586.00 ₹ 286.10 ₹

Cement Mortar 1:2 (1 Cement : 2 Coarse Sand) Finished With Trovel Including Scaffolding

Curing Etc. Complete.

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give

26 an required shape even shade after thoroughly brushing the surface to remove all dirt, and Smt 2,448.50 ₹ 70.32 ₹

remains of loose powdered materials.etc complete

Applying two coats of putty & two coats of primer of approved brand and manufacture on

27 new wall surface to give an even shade including thoroughly brushing the surface free from Smt 2,448.50 ₹ 40.59 ₹

mortar dropping and other foreign matter and sand papered smooth.

Supplying And Stacking Of Good Earth At Site Including Royalty And Carriage Upto 5 Km

Lead Complete (Earth Measured In Stacks Will Be Reduced By 20% For Payment).

Grassing With Selection No. 1 Doob Grass Including Watering And Maintenance Of The

Lawn For 30 Days Or More Till The Grass Forms A Thick Lawn, Free From Weeds And Fit

For Mowing Including Supplying Good Earth, If Needed (The Grass And Good Earth Shall

Be Paid For Separately).

Designing, fabricating, supplying, and installing a custom-designed sculpture of approved

artistic concept, size, and material (e.g., metal, stone, concrete, fiberglass, or mixed media),

including preparation of detailed 3D models/renders, structural support system (if required),

30 surface finishing (e.g., polished, painted, patinated), protective coating, transportation to Nos. 1.00 ₹3,36,835.00 ₹

site, positioning with crane/lifting equipment, anchoring, and final touch-up, complete in all

respects as per artist’s intent, architectural drawings, and approval of the Engineer-in-

Providing And Fixing Granite Stone Cladding Of Approved Quality, Color, And Thickness

(Typically 18–25 Mm), Machine-Cut And Mirror-Polished/Honed/Antique Finished (As

Specified), Fixed Over Plastered Rcc/Masonry Surface Using Cement Mortar 1:3 (1 Cement:

31 3 Fine Sand) Or With Mechanical Stainless Steel Clamps And Pins, Including Cutting, Edge Smt 109.50 ₹ 3,395.62 ₹

Polishing, Bedding, Joint Filling With Non-Staining Epoxy / Cement Grout, Curing, And

Cleaning, Complete In All Respects As Per Architectural Drawings, Sample Approval, And

Instructions Of Engineer-In-Charge.

Providing upto floor two level precast cement concrete jali or grill 1:2:4 mix (1- Cement : 2-

coarse sand : 4-graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia. Mild

32 steel wire including roughening,cleaning, fixing and finishing in cement mortar 1:3 and Smt 3,110.80 ₹ 853.91 ₹

curing complete.(E) 100mm thick All Complete As Per Drawings, Technical Specifications,

And Instructions Of The Engineer-In Charge.

Providing And Supplying Precast Concrete Light Poles Of Exposed Finish, 50Mm Thick,

Approx. 500 Kg Each, Fabricated Using High-Grade Opc Cement (Ultratech / Birla White /

Jk White), Crushed Coloured Stone Aggregates, 90% Silica Sand, Ar Grade Fibers (Roving

Ar2500H103 & Chopped Strand Acs13Ph901X), Fe 415 Steel, Non-Corrosive Admixtures

And Pure Iron Oxide Pigments. Poles To Be Cast In Custom Molds Ensuring Uniform

Thickness And Finish, Cured Properly, And Delivered Without Ms Plate And Light Fitting.

Steel work, welded in built up sections framed work including cutting, hoisting, fixing in

position and applying a priming coat of red lead paint. (A)In beams and joists, channels

angles Tees, flats, with connecting plates or angle cleats as in main and cross beams. Hip

and jack rafters, purlins conneted to common rafters and the like

Providing and fixing M.S. round holding down or anchor bolts with nuts and washer plates

Painting two coats (excluding priming coat) on new steel and other metal surface with

36 synthetic enamel paint, brushing to give an even shade including cleaning the surface of all Smt 280.00 ₹ 65.31 ₹

dirt, dust and other foreign matter.

Supplying only of Stainless Steel Bollards of 1-meter height, made from SS 202 grade

stainless steel, surface polished finish. Bollard comes in silver color with no applicable

warranty. Suitable for outdoor or pathway demarcation and basic vehicle restriction/security

Supplying 3mm thick fibre glass dustbins of 140-150 litres capacity (approximately) with

cm dia at bottom of thickness 4mm and 50 mm dia at top with 4mm thick reinforced edges

and 92 cm in height including lid of 50 cm dia with 4mm thick reinforced edges and 20 cm in

height having two circular slits of 15 cms in size adjacent to each other. Spray painting at

38 the outer surfaces with synthetic enamel paint (Two or more coats) over and under coat of Nos. 60.00 ₹ 1,969.50 ₹

primer including embossed moulding on dust bins indicating one side and “USE ME” &

“Using dustbin logo” on other side and making 5 Nos. small holes of size 2-3 cm dia at

bottom of the dust bins as per existing pattern/ design enclosed etc complete & as per the

direction of engineer-in-charge.

Cat Eye / Road Stud / RPM: Supplying Raised Pavement Markers made of polycarbonate

and ABS moulded body and reflective panels with Micro prismatic lens (No Glass bead lens)

capable of providing total internal reflection of the light entering the lens face and shall

support a load of 13635 kgs. tested in accordance to ASTM D 4280 Type H and complying

to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 Ð DO III Dt

39 11.06. 1997. The height, width and length shall not exceed 20 mm, 130 mm and 130 mm Nos. 1,024.00 ₹ 217.40 ₹

and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall

be 35 +/- 5 degree. The body of the marker should having finger grip for easy and accurate

placement and application with epoxy / bituminous Adhesive as recommended by the

manufacturer of the marker. The color of the marker should be as per the IRC 35-2015 and

as directed by Engineer-in-charge.

Facility Informatory Sign :-Providing and fixing sign boards made out of 2mm aluminium

sheet / 4mm ACP (Aluminum composite Panel); size 80 x 60 cms rectangular as per design

of IRC-67-2012. Pre treated with phospheting process & acid etching; coated with one coat

of epoxy primer and two coats of best quality epoxy paint ;reflectorised with Micro Prismatic

Grade retro refiectivesheeting of Type-11 as per ASTM D-4956 and latest

M.O.S.T.Specifications; 3.6mtr long stand post of 75 x 75 x 6mm / 65NB Circular MS Pipe

as required and frame fabricated from suitable size iron angle of 35 x 35 x 3mm; painted

with bestquality epoxy coatings in black and white bends. The details of symbol foreach

board shall be as per theinstruction of engineer in charge. The fixing at site shall be in 1:2:4

CC blockof size 45 x 45 x 60 Cms. for each leg.including excavation, curing etc.complete

under the supervision of engineer in charge. A warranty for 10 years for the Retro reflective

sheeting from original manufacturer & a certified copy of 3 year outdoor exposure test report

from third party test lab for the product offered shall be submitted by contractor. (A) Class-C

Type-11 Retro Reflective sheeting

STOP Sign :-Providing and fixing sign boards made out of 2mm aluminium sheet / 4mm

ACP (Aluminum composite Panel); size 90 cms Octagone as per design of IRC-67-2012.

Pre treated with phospheting process & acid etching; coated with one coat of epoxy primer

and two coats of best quality epoxy paint ;reflectorised with Micro Prismatic Grade retro

refiectivesheeting of Type-11 as per ASTM D-4956 and latest M.O.S.T.Specifications;

3.6mtr long stand post of 75 x 75 x 6mm / 65NB Circular MS Pipe as required and frame

fabricated from suitable size iron angle of 35 x 35 x 3mm; painted with bestquality epoxy

coatings in black and white bends. The details of symbol foreach board shall be as per

theinstruction of engineer in charge. The fixing at site shall be in 1:2:4 CC blockof size 45 x

45 x 60 Cms. for each leg.including excavation, curing etc.complete under the supervision

of engineer in charge. A warranty for 10 years for the Retro reflective sheeting from original

manufacturer & a certified copy of 3 year outdoor exposure test report from third party test

lab for the product offered shall be submitted by contractor. (A) Class-C Type-11 Retro

Reflective sheeting

Parking Sign :-Providing and fixing sign boards made out of 2mm aluminium sheet / 4mm

ACP (Aluminum composite Panel); size size 60 x 60cms. square plus 60 x 20cms

rectangular additional plate as as per the design of IRC-67-2012. Pre treated with

phospheting process & acid etching; coated with one coat of epoxy primer and two coats of

best quality epoxy paint ;reflectorised with Micro Prismatic Grade retro refiectivesheeting of

Type-11 as per ASTM D-4956 and latest M.O.S.T.Specifications; 3.6mtr long stand post of

75 x 75 x 6mm / 65NB Circular MS Pipe as required and frame fabricated from suitable size

iron angle of 35 x 35 x 3mm; painted with bestquality epoxy coatings in black and white

bends. The details of symbol foreach board shall be as per theinstruction of engineer in

charge. The fixing at site shall be in 1:2:4 CC blockof size 45 x 45 x 60 Cms. for each

leg.including excavation, curing etc.complete under the supervision of engineer in charge. A

warranty for 10 years for the Retro reflective sheeting from original manufacturer & a

certified copy of 3 year outdoor exposure test report from third party test lab for the product

offered shall be submitted by contractor. (A) Class-C Type-11 Retro Reflective sheeting

Direction (Junction) Sign :-Providing and fixing sign boards made out of 2mm aluminium

sheet / 4mm ACP (Aluminum composite Panel); size 244x122 cms. rectangular as per

design of IRC-67-2012. Pre treated with phospheting process & acid etching; coated with

one coat of epoxy primer and two coats of best quality epoxy paint ;reflectorised with Micro

Prismatic Graderetro refiectivesheeting of Type-11 as per ASTM D-4956 and latest

M.O.S.T.Specifications; 4.0mtr long (2 Nos.) stand post of 75 x 75 x 6mm / 65NB Circular

MS Pipe as required and frame fabricated from suitable size iron angle of 50 x 50 x 5mm;

painted with bestquality epoxy coatings in black and white bends. The details of symbol

foreach board shall be as per theinstruction of engineer in charge. The fixing at site shall be

in 1:2:4 CC blockof size 45 x 45 x 60 Cms. for each leg.including excavation, curing

etc.complete under the supervision of engineer in charge. A warranty for 10 years for the

Retro reflective sheeting from original manufacturer & a certified copy of 3 year outdoor

exposure test report from third party test lab for the product offered shall be submitted by

contractor. (A) Class-C Type-11 Retro Reflective sheeting

Place Identification Sign 'Providing and fixing sign boards made out of 2mm aluminium

sheet / 4mm ACP (Aluminum Composite Panel), size 150x90 cms rectangular as per IRC-67-

2012 design, pre-treated with phosphating process & acid etching, coated with one coat

epoxy primer and two coats of best quality epoxy paint, reflectorised with Micro Prismatic

Grade retro reflective sheeting Type-11 as per ASTM D-4956 and latest M.O.S.T. specs,

44 with 4.0m long (2 Nos.) stand posts of 75x75x6mm / 65NB circular MS pipe and frame of Each 5.00 ₹ 14,085.46 ₹

35x35x3mm iron angle painted with black & white epoxy coating, symbols as per engineer's

instruction, fixed at site in 1:2:4 CC blocks of 45x45x60 cms including excavation, curing

etc., complete under engineer’s supervision, with 10-year warranty for reflective sheeting

and certified 3-year outdoor exposure test report from third party lab for product offered, (A)

Class-C Type-11 Retro Reflective sheeting.

Providing and stacking of Ficus bengalensis (Bargad) of height 120-135 cm. in big poly

bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags

of size 25 cm as per direction of the officer-in-charge.v

Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of

size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Mangifera indica (Mango-grafted ) of height 60-75 cm. in big poly

bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Milletia ovalifolia of height 120-135 cm. in big poly bag of size

cm as per direction of the officer-in-charge.

Providing and stacking of Nauclea cadamba (Kadam) of height 150-165 cm. in big poly bag

of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Bougainvillea (Variety Butiana, Lady Mary Baring,

Mahara,Mohan,Scarlet Queen, Variegated, Glabra Formosa, Peruviana Odissi, Paratha,

51 Subhra,Thimma, Spectabilis L.N Birla, Refulgens) of height 30 cm. to 45 cm. with 2-3 Each 70.00 ₹ 40.40 ₹

branches in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-

52 Wadelia trilobata,full of leaves in 15 cm size of Earthen Pot / Plastic Pot. Each 250.00 ₹ 15.15 ₹

Providing and stacking of Ipomea (Golden leaves),with fresh and healthy leaves in 15 cm

size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Cestrum nocturnum (Raat ki Rani) of height 60- 75 cm. with 4-5

branches in bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Hamelia patens (Dwarf ) of height 30-45 cm. with 3-4 branches in

55 earthen pots of size 20 cm as per direction of the Each 350.00 ₹ 40.40 ₹

officer-in-charge.

Providing and stacking of Chlorophytum (Green), full of leafy suckers in 15 cm size of

Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Dombeya mastersii of height 60-75 cm. with 4-5 branches in bag

of size 25 cm as per direction of the officer-in-charge.

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable

material’s as per direction of officer in charge (excluding cast of plant & water)

59 2.57.1 Trees Plant Each 360.00 ₹ 7.37 ₹

60 2.57.2 Shrubs Plan Each 3,700.00 ₹ 3.69 ₹

Road marking with hot applied thermoplastic paints with reflectorising glass beads on

bitumin surface providing and laying a hot applied thermoplastic compound 2.5 mm thick

including reflectorising glass beads @ 250gms per sqm area, thickness of 2.5mm is

excluding of surface applied glass beds as per IRC:35-2015. The finished surface to be

level, uniform and free from streaks and holes. zebra patta /bump patta lane/center line/

edge line/cut patta. The white color marking should provide liminance coefficinet on cemend

road shalll be min 130 mcd/m2/lux and Asphalt road shall be min 100 mcd/m2/lux during the

service life during the day time. The marking should meet the performance criteria for night

time reflectivity, wet reflectivity and skid resistance as mentioned in the section-15 of IRC 35-

2015. Warranty for the Retro reflectivity should be two years.

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor

type cubical panel board necessary IP-42 and above protection as per approval from

engineer incharge made from 14 SWG thick CRC M.S. sheet for outer body & doors,

SWG thick CRC M.S.sheet for internal partitions with necessary accesories , supporting

angles/ flats channel including cutting, bending, drilling, welding, riveting with internal

partitions & cable alley as per requirements & instruction of engineer-in-charge with erection

of supplied switch gears, BUSBARS, suitable size of inter connecting PVC copper wire /

copper-aluminium strips, rubber grommets, rib, bakelite control fuses/MCB for measuring

62 instruments, earth bus & earth bolts, foundation flange - bolts-base Plates, sufficient nos. of Sq Mtr 5.00 ₹ 16,392.30 ₹

hinged doors, handles with locking arrangement and rubber gasket,heavy duty end terminal

connection,danger notice board,necessary ventilation,earthing strip complete. The Panel

shall be painted with epoxy powder coating. (The rates excludes the cost of switchgears,

bus bars, inter connecting mains & Copper Aluminium strips, meters, Fuses etc. The

dimension shall be measured excluding base beams) The panel shall be supplied with

following approved manufacturers with following size.(C) The standard companies switch

gear shall be used and only manufacturers as per IEC 61439 for beneficial use. (i) with

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having

63 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity (a) Ea 40.00 ₹ 595.90 ₹

6 to 32 Amp. Cat.III

Supplying and erecting approved make panel mounting type Digital Ammeter having

digits LED display, external CT operated, calibrated for 0 to 1000 Amps. suitable to operate

on 500 Volt AC,0.5 class accuracy erected on existing panel board with all connection,

wiring etc. with manufacturers calibration certificate.

Supplying and erecting approved make panel mounting type Digital Voltmeter having

65 digits LED display, 0 to 750 AC Volts range erected on existing panel board with all Ea 6.00 ₹ 1,275.63 ₹

connection, wiring etc .with manufacturers calibration certificate.

Supplying and erecting approved make suitable panel indicator LED type lamp, lens cover,

complete erected with necessary connections.

Providing and erecting multifunctional meter suitable for application of Power monitoring

and showing measurement of following Voltage, Frequency, Apparent energy, Apparent

power, Active and reactive energy, Active and reactive power, Average voltage Vavg, Peak

demand power PM, QM, SM, Demand power P, Q, S, Apparent power S, S1, S2, S3,

Unbalance current, Power factor and displacement PF (signed, four quadrant), Calculated

67 neutral current, Active, reactive, apparent energy (signed, four quadrant), Active power P, Ea 1.00 ₹ 14,123.84 ₹

P1, P2, P3, Voltage U21, U32, U13, V1, V2, V3, Phase currents, Average current Iag, Peak

demand currents, Reactive power Q, Q1, Q2, Q3, Demand current I1, I2, I3, [Us] rated

supply voltage 40...300 V AC 45...65 Hz, 40...300 V DC, Network frequency 50 Hz, Type of

network 3P, Display type 7 segments LED, Display colour Red, Messages display capacity

3 fields of 4 characters, Display digits 12 digit(s) - 14.2 mm in height

Providing and erecting Approved make Four pole moulded case circuit breaker having

breaking capacity ICU of 25 KA. at 415 V,having normal current rating up to 25 A to 100A.

68 with Fixed thermal & magnetic release suitable to work on A.C. supply 50 c/s. with all Ea. 1.00 ₹ 6,173.12 ₹

internal connections, spreader tinned copper & complete erected in existing 16 G.M.S.

housing. ICS=100% of ICU only Cat III

Providing and erecting metallic vitrified danger notice board as per language suggested by

engineer incharge for MEDIUM VOLTAGE installation to be erected as per IS-2551.

Supplying and erecting triple pole & neutral 440V/ 500V panel mounting Aluminium Busbars

with four equal Nos. of bus having current density not more than 0.8 Amp. / sq.mm (Rated

current / cross section area) duly wrapped with colour insulating tape for phase sequence of

following current carrying capacity, erected with necessary bus bar supports /insulators,

main cable socket to each busbar,erected in existing cubical panel with necessary

connections. (A) Suitable for 100 Amp. Capacity

Providing and erecting busbar chamber confirming to IS-375 fabricated from 16 G.M.S.

sheet, dust & vermin proof having hinged door with rubber gasket and necessary busbar

supports with Aluminium busbar having current density not more than 0.8 Amp. / sq.mm

71 (Rated current / cross section area) duly wrapped with colour insulation tape for phase Rn.Mtr 2.00 ₹ 2,602.77 ₹

sequence, three phase & neutral each Suitable for following current capacity with necessary

painting mounted on wall or pedestal frame of required size with necessary connections.(A)

Suitable for 63/ 100 Amp. Capacity

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to operate on

72 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. Ea 16.00 ₹ 112.11 ₹

confirming to IS 8828/1996 with ISI Mark Cat.III

Supplying & erecting approved make SMC press moulded composite FRP. loop-in, loop-

out approx. 2mm thick box complete with Bakelite connector strip 5way(3P+N+E),DIN rail for

73 mounting mob & hinged doors as per requirement having locking arrangements with Ea 326.00 ₹ 476.72 ₹

mounting clamp with nuts, bolts & washers suitable for erection on pole with cable clamps&

earth bolt of following size of box.(C)150mm x 125mm x 100mm [deep]

Providing and erecting iron clad cable route marker duly marked with ELE.CABLE of size

cm.X 12 cm. Flushed with ground in cement foundation as directed by Engineer in charge.

Supplying and erecting LED street light / Flood light fittings with High power White LEDs

wattage of 3 Watt and above assembled on single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses,

with toughened glass with company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79

& LM-80 certificates)(NOTE: Below description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any wattage capacity between the ranges

75 shown.) (C) Post Top Lantern LED fitting comprises of finish cast aluminum spigot and spun Ea 326.00 ₹ 4,819.72 ₹

aluminum canopy fixed with opal polycarbonate, pipe arrangement for vertical mounting

driver and accessories wired upto terminal block.IP 65 40W cat-III

Supplying and erecting LED street light / Flood light fittings with High power White LEDs

wattage of 3 Watt and above assembled on single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast aluminium housing with smooth finish powder

coated and heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses

with company mark/name engraved or embossed 160 to 270 V,Power Factor more than

76 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 Ea 50.00 ₹ 1,195.84 ₹

lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line

supply with over-voltage protection.(i) 10 to 12 Watts Cat-lll

Supplying and erecting LED street light / Flood light fittings with High power White LEDs

wattage of 3 Watt and above assembled on single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses,

with toughened glass with company mark/name engraved or embossed 160 to 270 V,Power

77 Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Ea 8.00 ₹ 5,194.43 ₹

Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79

& LM-80 certificates)(NOTE: Below description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any wattage capacity between the ranges

shown.) (B) Flood Light (IP-68), Surge protection -4KV integral and ,Light must have

440VAC line supply with over-voltage protection. (i) above / = 40 watts Cat-lll

Supplying & erecting IP 55 grade following size section pillar fabricated from joint less M.S.

Sheet with angle iron legs made from jointless M.S. Angle with cable clamps to be buried in

ground to have appropriate erection to work uniform until erected with cement concrete

foundation and 45 cm high bricks work finishing with plaster etc. hinged double door

internally supported on both side,with internal and outside looking arrangement with look

78 and keys in duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos. one is welded and other with Ea 4.00 ₹ 1,884.66 ₹

nut and bolt for erecting Bakelite sheet. Painting the Section Pillar inside and out side with

three tank powder coated paint. section pillar roof should be without joint with water leakage

proof & tested as per IP 55 test & followed by IS 2147 of 1962 (C) 60 X 30 X 45 cm section

pillar fabricated from 16 Gauge MS Sheet with angle iron legs 45 cm long made from 35 X

35 X 5 mm thick MS angle.

Supplying & erecting approved make IP 55 grade Company fabricated Timer Panel of

following capacity for switch On-Off street lights on time scheduling basis made from 16G

CRCA sheet duly epoxy power painted inside and outside with hinged doors and locking

arrangement consisting of suitable size of 4 Pole MCB and 4 pole contactor (cat-III)with

analog time switch, auto manual switch of same make and suitable input and output

Bakelite terminals and with door earthing approved by Engineer in charge.(A) 32 Amp

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / Solid

80 Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing Mtr 3,500.00 ₹ 117.16 ₹

trench / pipe of following size of cables (A) 4 core 4 Sq. mm (Street Pole To street Pole)

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / Solid

81 Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing Mtr 2,000.00 ₹ 140.39 ₹

trench / pipe of following size of cables (C) 4 core 10 Sq. mm (Main panel to section piller)

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC

82 insulated armoured cable complete with out going tails, insulating tape etc for following size Ea. 50.00 ₹ 33.33 ₹

of cables. (A) 2 to 4 core 2.5/4 Sq. mm (for street light circuit)

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC

83 insulated armoured cable complete with out going tails, insulating tape etc for following size Ea. 10.00 ₹ 38.38 ₹

of cables. (C) 2 to 4 core 10 Sq. mm (from main panel to feeder pillar)

Providing and, fixing heavy duty flange type brass double compression type cable gland

84 with rubber ring for PVC insulated armoured cable complete with out going tails, insulating Ea. 2.00 ₹ 75.75 ₹

tape etc for following size of cables. (B) 3 & 1/2 core 35/50 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium

85 conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe Mtr 100.00 ₹ 255.53 ₹

of following size of cables(C) 4 core 35 Sq. mm (for the main panel)

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following

86 size evenly crimped with high pressure tool & connected to switchgear terminals with Ea. 20.00 ₹ 6.06 ₹

brass/cadmium plated nut bolts in an approved manner. (A) 4 Sq.mm.

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following

87 size evenly crimped with high pressure tool & connected to switchgear terminals with Ea. 10.00 ₹ 13.13 ₹

brass/cadmium plated nut bolts in an approved manner. (B) 10 Sq.mm

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following

88 size evenly crimped with high pressure tool & connected to switchgear terminals with Ea. 8.00 ₹ 20.20 ₹

brass/cadmium plated nut bolts in an approved manner. (D) 35/50 Sq.mm.

Making trench in soft soil of suitable width of 90 cm deep for laying cable or locating the

fault all over the run and back filling the same and making the surface as normal ground.

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same

material at required depth in existing trench for laying of cable. below ground / road surface

for enclosing cable (B)63 mm outer dia

Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cm. below ground across the

91 road crossing or on floor with necessary material in an approved manner and making the Mtr. 300.00 ₹ 263.61 ₹

ground as per original.(E)150 mm dia

Dismantling the existing pole up to 6 m height with brackets, clamps, insulators, stay from

92 the cement concrete foundation and making the site clear by refilling the pits with excavated Ea. 190.00 ₹ 184.83 ₹

materials and bringing it to the ground level.

Dismantling the existing any type of street light fittings on pole up to 6 mt height with bracket

and making the site as original complete.

Dismantling the existing underground cable without damaging it with glands, cable end box

94 including refilling the trench up to ground level and making coils complete to be placed at Mtr. 1,500.00 ₹ 10.10 ₹

different store.

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are

of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr

length , in below type of pipe erected with 6A Modular type switch / bell push & accessories

and earth continuity of following type, erected on PVC / Metallic/Wooden box, single

mounting base frame covered with textured/metallic/white front plate modules erected on /

in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose /

H.D.Connector as directed. (a) with medium class Rigid PVC pipe and accessories erected

flushed on wall/ceiling complete Cat. III

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete

to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes

fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as

directed (a)20 mm

Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms. dia. galvanised

97 iron pipe with coupling and buch buried in specially prepared earth pit complete with Ea. 370.00 ₹ 368.65 ₹

necessary 8 SWG earth wire. - to be used for each Street Light

98 For using salt and charcoal / coke as required for pipe type earthing. Ea. 370.00 ₹ 171.70 ₹

Providing one bag of 25 Kg. Additional Back Filling Compound (BFC) suitable for safe

earthing device.

100 Providing and erecting HOT deep Galvanised iron strip wire 8 to 16 SWG. Kg 200.00 ₹ 77.77 ₹

Supplying & erecting in earthpit of minimum bore dia. 225mm size approved make Safe

Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of

corrosion free hot dipped G.I.Pipes having Outer pipe dia of 80 mm having 80-200 Micron

galvanising, Inner pipe dia of 40 mm having 200-250 Micron galvanising, connection

terminal dia of 14 mm with constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for following type of applications with

chamber and heavy duty cover (A)(approved make OEM has to submit test certificate

including value of earth resistance of installation duly stamped and signed by agency and

officer Incharge has to ensure the value of earthing resistane mentioned in test Certificate)

& having back filling compound of (B) Inner chemical (CCM Compound)- Resistivity:-

ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry form,

Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable to

retain moisture for long time Necessary test report must be submitted by Agency. [A] For

electrical installation up to 440 V

Length of Pipe - 1 Mtr

Back filling compound - 1 Nos. of Bag of 15 Kgs.

Supplying and fixing reinforced concrete heavy duty non-pressure pipes with collars for

culverts carrying heavy traffic as per IS 458-1991 specifications including setting the pipes

in C.M. 1:2 watering and laying (to level or slopes) of class NP3 of following internal

daimeters.(ii) 450mm dia.

Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe ( SCH- 80) for

cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the

103 wall with the help of clamp at every two metre C/C or shall be concealed as directed Mtr 50.00 ₹ 195.67 ₹

including necessary fittings etc. including testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

104 Providing and fixing Gun metal check or non-return fullway wheel valve.(E) 50mm dia. Nos. 2.00 ₹ 663.43 ₹

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends

with bricks having crushing strength not less than 35Kg/Cm2 in C.M. 1:5 C.I. cover with

frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be

not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with

1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation

concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a

floating coat of neat cement on walls and bed concrete etc. complete.(i) Inside dimensions

455mmx 610mm and 450mm deep for single pipe line.

106 Providing and fixing ball cock of approved. quality as directed.(B) Abonite (ii) 50mm dia. Nos. 1.00 ₹ 137.89 ₹

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse sand : 4-graded

stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix

(1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with

Cement Mortar 1:3 (1-Cement : 3-coarse sand) finished with a floating coat of neat cement

and making channels in cement concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-stone

107 aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Nos. 75.00 ₹ 11,029.97 ₹

Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm

diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg.

and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having

crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse

sand) (1) A type depth 0.90 Metre

(I) Extra rate for constructing B.B. masonry for every additional depth of 0.1M. or Part

thereof over item No.24.27 (I) for depth from 0.9M to 1.5M.

(II) Extra rate for constructing B.B. masonry for every additional depth of 0.1M. GR Part

thereof over item No.24.27 (I) for depth from 1.50M. to 2.25M.

(III) Extra rate for constructing B.B. masonry for every additional depth of 0.1M. or Part

thereof over item No. 24.27 (III) for depth from 2.25M to 3.15M.

Supplying & erecting approved make self-priming domestic monoblock water pump with

H.P motor, suitable for operation on 230 volts, 50c/s. AC supply with metallic flange, and

M.S. impeller delivery and following discharge

100 LPM at 14 mtrs. head suitable for 25 mm dia. delivery Cat.III

I / We am / are willing to carry out the work at __________% above / below __________ percentage (should be written in figures and words)

Estimated Amount put to

Deduct _________ % Below.

Notes 1 - All work shall be carried out as per Public Works Department Handbook and other

specifications of Division or as directed.

Notes 2 - All the columns in Schedule should be filled in ink and the total of the entries in the last

column should be struck by the contractor under his signature.

Notes 4 - To be continued on additional sheets, if found necessary .