Special repairs to NOIC APD staff officers on 4th floor, MWC building No- P-61 and DCN Node building No.T-172 and As and As and improvement to the drying shed of mechanical laundry adjacent to building No. P-113 at INHS Kalyani under GE NB, Visakhapa

Amount

Surface Excavation not exceeding 30cm deep and averaging 15 cm deep and getting out in Soft / Loose soil complete all as specified and as directed.

Excavation in post holes each not exceeding 0.5 Cu.m, getting out in Soft / Loose soil, including returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm thick, watering and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m deep and getting out in Soft / Loose soil complete all as specified and as directed.

M & L for Moorum / Red Bajri filling under Floors or in Pavings laid in layers not exceeding 15 cm thick, spread levelled and rammed / rolled including watering to required level and gradient complete all as specified and as directed. Note: Measurements shall be taken after consolidation of earth and 10% deduction shall be made for payments.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming.

Removal of excavated material [Soil] to a distance exceeding 1.5 KM but not exceeding 5 KM and depositing where directed at a level not exceeding 1.5 m complete all as specified and as directed.

M & L for Hardcore of gauge not exceeding 63mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface complete all as specified and as directed.

M & L for Hardcore of gauge not exceeding 63mm of broken bricks, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface complete all as specified and as directed.

M & L for providing pre construction anti termite treatment for treating the bottom and sides of excavation by applying emulsion at the rate of 5 litres per square metre of surface area complete all as specified and as directed.

M & L for providing pre construction anti termite treatment for the soil filled under floors by applying emulsion at the rate of 5 litres per square metre of surface area complete all as specified and as directed.

M & L for providing pre construction anti termite treatment to the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and as directed.

Demolition of Plain Cement Concrete in ground floors and Pavings not exceeding 15cm thick [below or above ground level] and removing rubbish to a distance exceeding 1.5 KM but not exceeding 5 KM complete all as specified and as directed.

Demolition of Plain Cement Concrete of any description and in any position not otherwise specifically provided for and removing rubbish to a distance exceeding 1.5 KM but not exceeding 5 KM complete all as specified and as directed.

Demolition of Reinforced Cement Concrete [reinforcement cut as required to facilitate demolition] of any description and in any position not otherwise specifically provided for and removing rubbish to a distance exceeding 1.5 KM but not exceeding 5 KM complete all as specified and as directed.

M & L for PCC 1:2:4, Type B-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed.

M & L for PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed.

M & L for PCC 1:3:6, Type C-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed.

M & L for providing Precast Cement Concrete, 1:2:4, Type B1, using 20mm graded stone aggregate as in shelves, Cover slabs for drains and the like and setting in Cement Mortar 1:4 complete with joints to match complete all as specified and as directed.

M & L for PCC 1:2:4, Type B-1, using 20 mm graded stone aggregate as in Coping, Bed plate, cill and the like including weathering, slightly rounded or chamfered angles and throating including formwork [straight or curved] complete all as specified and directed.

M & L for PCC 1:3:6, Type C-1, using 20 mm graded stone aggregate as in Coping, Bed plate, cill and the like including weathering, slightly rounded or chamfered angles and throating including formwork [straight or curved] complete all as specified and directed.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels etc complete all as specified and as directed.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in chajjas and the like complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in Cement Mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting exceeding 20 cm girth brick walls complete all as specified and as directed.

Demolition of Brick / Stone Masonry built in Cement Mortar including all quoins arches pillars etc and removing rubbish to a distance exceeding 1.5 KM but not exceeding 5.0 KM complete all as specified and as directed.

M & L for brick work with Fly Ash bricks, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

M & L for brick work with Fly Ash bricks, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:4 complete all as specified and as directed.

M & L for brick work in half brick thick walls using Fly Ash bricks straight or curved on plan to any radius built in Cement Mortar 1:4 including 2 Nos of 8mm dia bars at every fourth course of brick work complete all as specified and as directed.

M & L for walling of random rubble masonry, uncoursed, well bonded, bedded and solidly hearted, built in Cement Mortar 1:6 complete all as specified and directed.

Use and removal of steel formwork to sides and soffits of floor or roof beams, beam launchings, girders, bressummers, lintels, cantilevers, shelves and similar works for rough finished surfaces of concrete complete all as specified and as directed.

Use and removal of steel formwork to sides and soffits of chajjas and similar works for rough finished surfaces of concrete complete all as specified and as directed.

Dismantling Timber Scantlings 40 Sq.cm and over in section, in any position, framed complete all as specified and as directed.

Taking down Wooden Chowkats or frame with shutters [without taking off shutter from the frame] not exceeding 1.5 Sq.m each complete all as specified and as directed.

Taking down Wooden Chowkats or frame with shutters [without taking off shutter from the frame] exceeding 1.5 Sq.m but not exceeding 4.00 Sq.m each complete all as specified and as directed.

Taking down Aluminium frame and shutters exceeding 1.5 Sq.m but not exceeding 4.00 Sq.m each complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment at points of contact of wood work by chemical emulsion [in oil or kerosene based solution] @ 0.5 litre per hole by drilling 6 mm dia holes at a downward angle of 45 degrees at 150 mm centre to centre and sealing the same complete all as specified and as directed.

S & F Second Class Hard Wood, plain, solid, straight Chowkats and Frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

S & F 30 mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels with decorative face veneers on both sides including provision of teak wood lipping 6mm thick alround complete all as specified and as directed.

S & F Factory made solid panel PVC door shutter 30 mm thick [Style] consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC "C" Channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement supplying & fixing in frame at site as per specification & drawing of Sintex or its equivalent make as approved by Accepting Officer complete all as specified and as directed.

S & F Solid PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening of Sintex or its equivalent make as approved by Accepting Officer complete all as specified and as directed.

S & F Factory made ready to install Non-Toxic, Lead & Cadmium free, single extruded, Water proof, termite proof, fire retardant, excellent screw holding capacity, Solid PVC Boards, 18mm thick, One Side Decorative Choice Lamination and other side Balancing White as in Cupboard Shutters complete all as specified as directed.

S & F Factory made ready to install Non-Toxic, Lead & Cadmium free, single extruded, Water proof, termite proof, fire retardant, excellent screw holding capacity, Solid PVC Boards, 18mm thick, Both Side Laminated in White as in Cupboard Shelves fixed to Guide Rails with stainless steel screws complete all as specified as directed.

S & F Factory made UPVC Sliding Window, Three Track, White Colour of area not exceeding 2.0 Sq.m, made of extruded profiles with wall thickness of 2.3mm±0.2mm, Window profile with hollow section with multi chamber, 112mm X 45mm, Sliding Sash of size 42mm X 67mm, Sliding Mesh Sash of size 42mm X 57mm, Sliding Interlock [One vertical length in each shutter] of size 45.50mm X 28mm, Glazing Bead of size 24.50mm X 16mm shall be mitred cut and fusion welded at all corners, including drilling holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM Gasket, 1.2mm±0.2mm thick Galvanized Steel Frame of size 30mmx 12mm, 2 Nos, Sliding Sash of size 30mm x 18mm, Sliding Mesh Sash of size 26mm x 10mm profile to be inserted in required profile, frame shall be fixed to the wall with 8mm X 100mm long fasteners, Hardware such as Touch lock of zinc alloyed [white powder coated], Steel roller system, including all necessary accessories shall be provided with proper operative and locking hardware mechanism, frame shall be fixed to wall with high quality fasteners and silicon glue shall be applied to fill up gap between frame and wall to make leak proof complete all as specified and as per Manufacturer instructions. Note: (a) Net opening will be measured for payment purpose. (b) Supply only of Wire mesh, deco grills and glass shall be measured and paid separately under relevant Items of Schedule 'A' / BoQ. (c) The size of UPVC sections specified in the description of item is minimum requirement, if the same size of section is not available, next higher size shall be provided by the contractor without any extra cost to the Department.

S & F Factory made UPVC Casement Door [Openable], White Colour, made of extruded profile with wall thickness of 2.3 mm±0.2 mm, Door profile with hollow section with multi chamber, Frame of size 67 mm x 64 m, Sash of size 67 mm x 110 mm, T Profile [one vertical length in between two shutters] of size 60 mm x 74 mm, Glazing Bead of size 35 mm x 20 mm shall be mitred cut and fusion welded at all corners, including drilling holes for fixing hardware and drainage of water, etc. making arrangements for fixing of hardware, EPDM Gasket of size 1.2mm±0.2 mm thick, Galvanised Steel Frame of size 28 mm x 21.5 mm, Sash of size 31 mm x 27.5 mm, T Profile of size 27 mm x 17 mm to be inserted in required profile, frame shall be fixed to the wall with 8 mm x 100 mm long fasteners, Hardware such as Casement Door handle made of zinc alloy [white powder coated], Corner Striker, Secondary Strikers, Cylinder, Door Transmission Gear made of mild steel with multi point locking system with strikes, 3D Hinges of zinc alloyed [white powder coated] and 8 mm thick Solid Colour PVC Sheet complete all as specified and as per Manufacturer instructions. Note: (a) Net opening will be measured for payment purpose. (b) The size of UPVC sections specified in the description of item is minimum requirement, if the same size of section is not available, next higher size shall be provided by the contractor without any extra cost to the Department.

S & F Factory made UPVC frame/ Partitions, White Colour, made of extruded profile with wall thickness of 2.0 mm±0.2 mm, Extruded profile with hollow section with multi chamber, Frame of size 42 mm x 50 m, (Tolerance±0.2 mm) Panel Bead of size 35 mm x 20 mm shall be mitred cut and fusion welded at all corners, including corners of the frame jointed with galvanised brackets and stainless steel screws, joints mitred and plastic welded, frame shall be fixed to the wall with 8 mm x 100 mm long fasteners, fixing of 12 mm thick prelaminated particle board panels complete all as specified and as per Manufacturer instructions. Notes: (a) Net opening will be measured for payment purpose. (b) The size of UPVC sections specified in the description of item is minimum requirement, if the same size of section is not available, next higher size shall be provided by the contractor without any extra cost to the Department. (c) Supply only of prelaminated particle board panels shall be measured and paid separately under relevant Items of Schedule 'A' / BoQ.

M & L for Powder coated aluminium sections [Minimum 50 Micron thick] of approved colour for Doors, Windows, Ventilators, Partitions with frame and shutters fully or partly glazed, sliding / openable including necessary jointing cleats, glazing clips, rubber beading, neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as handles, aluminium butt hinges, aluminium tower bolts, stainless steel friction hinges, locking arrangements etc., complete all as specified and as directed. Notes: [a] The size of aluminium sections shall be all as specified in relevant IS code and MES Schedule Part - I. [b] Panel inserts such as Glass / Particle board / Gauze/ Grills shall be measured and paid separately at supply only rates. [c] Weight of aluminium sections shall only be accounted for payment purpose. Weight of aluminium Handles, Butt Hinges & Tower Bolts shall not be accounted for payment purpose. [d] The unit rate quoted shall be deemed to include for cost of jointing cleats, glazing clips, rubber beading, neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as handles, aluminium butt hinges, aluminium tower bolts, stainless steel friction hinges, locking arrangements etc., and fixing only of panel inserts of glass / particle board / gauge/ grills etc.

Supply only 12mm thick Prelaminated Particle Board, both Side Decorative Choice Lamination, Medium Density, Interior Grade complete all as specified and as directed.

Supply only 5.5mm thick plain sheet Glass ordinary quality in squares exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

Supply only 4.8mm thick tinted sheet Glass in squares exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

Supply only Stainless steel wire cloth / mesh with average aperture not exceeding 1.40 mm and dia of wire 0.36 mm complete all as specified and as directed.

Supply only Powder Coated Aluminium Deco Grill of Model / Design No. DG 104 (7mmx4.2mm), including Powder Coated Aluminium Channel of size 20 X 12 X 1.5mm for fixing Deco Grill complete all as specified and as directed.

S & F Continuous [Piano] Hinges, Mild Steel, Bright finish or electrogalvanised and width of Flaps 40mm [When Open] complete all as specified and as directed.

S & F 40mm dia MS Cupboard Knobs, bright polished, fixed with nut, screw and washer complete all as specified and as directed.

S & F 125 mm size, Butt hinges, Extruded Aluminium alloy with galvanised mild steel hinge pin, anodised, Type B-22, including fixtures complete all as specified and as directed.

S & F 100 mm size, medium weight Butt Hinges, cold rolled, mild steel including fixtures complete all as specified and as directed.

S & F Aluminium anodised barrel Tower Bolt of size 200 mm size of extruded section complete all as specified and as directed.

S & F Aluminium anodised barrel Tower Bolt of size 150 mm size of extruded section complete all as specified and as directed.

S & F Aluminium anodised Handle, of extruded section Fabricated Type of size 150mm long complete all as specified and as directed.

S & F Aluminium anodised Handle, of extruded section Fabricated Type of size 100mm long complete all as specified and as directed.

S & F Floor Door Stopper of size 150 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed.

S & F Aluminium alloy anodised Sliding Door Bolt with hasp and staple [Bolt Type] of size 300 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F in repairs Door Closer of aluminium body, Hydraulically Regulated, Designation No. 3 universal type, suitable for door shutters of 851 mm to 1000 mm in width and of weight between 61 to 80 Kg complete all as specified and as directed.

S & F in repairs Curtain Rods of PVC coated mild steel, 25 mm dia with fixing brackets, stops, rollers etc complete all as specified and as directed.

S & F Name Plates of size not exceeding 0.5 square metre with black background and golden letters of size not exceeding 10 cm height, Letters made of brass sheet, standard quality, bright polish finish, fixed on Plastered Surfaces / Granite Dado / Lining etc. complete all as specified and as directed.

S & F in repairs 12mm thick, Prelaminated Particle Board, both sides Decorative Choice Lamination Medium Density, Interior Grade fixed with screws to wooden frames / aluminium frames complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

Dismantling of Mild Steel or Wrought Iron Work of any description not otherwise provided for complete all as specified and as directed.

S & F Mild Steel work as in Tubular Trusses, Posts etc including special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS - 1161, Grade YST - 240, Medium Grade of any dia complete all as specified and as directed.

S & F Rolled Mild Steel work confirming to Fe 410-W, Grade-E- 250, Quality-A as in Roof Trusses [framed], trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing [Beam, tee, angle, channel or flat sections] including distance pieces, cleats etc complete all as specified and as directed.

S & F Mild Steel work confirming to Fe - 290, Grade E-165 as in Framed Brackets of Angles or Tees with web and flanges cut to shape, drilled and counter shank for screw including bending and welding angles as necessary, gusset plates riveting etc, not exceeding 10 Kg each bracket complete all as specified and as directed.

S & F Mild Steel work confirming to Fe - 290, Grade E-165 as in Hand Rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for Balusters Running Bars, for Doors, Balusters, Nosing to Steps including embedding in concrete and screwing etc, Wind Ties for roof including securing bolts, Posts and Struts in Fencing including cutting tops to shape as directed, bending to shape, notching for wire, drilling holes or as in flat iron fillets [for securing wire mesh and barbed wire etc] including all necessary drilling, bolting or riveting, etc and similar work complete all as specified and directed.

S & F Rolled Mild Steel work confirming to Fe 410-W, Grade-E- 250, Quality-A as in Plates [plain & chequered], Channels, Angles, square cut or notched [ordinary or counter sunk] forming holes without any attachment complete all as specified and as directed.

S & F MS machine made screw bolts with hexagonal or square head one end and screwed other or screwed both ends, fitted with washers and one hexagonal or square nut exceeding 5cm and not exceeding 10 cm long, dia of neck exceeding 11 mm but not exceeding 15 mm complete all as specified and as directed.

S & F Stainless Steel Railing made with Stainless Steel Pipes of wall thickness not less than 1.6mm, of Grade AISI 316L, standard quality, bright polish finish, using 50mm dia pipes for hand rail, 25mm dia pipes for vertical supports / balusters and 25mm dia pipes as in tie bars in three layers, SS tubes shall be welded at the turnings and junctions, welded portions shall be completely grinded and brought to bright and smooth finish including all bends, elbows, making holes in the floor / steps, grouting with epoxy to achieve full strength of railing complete all as specified and as directed.

Dismantling of Plain or Corrugated Steel sheeting of any gauge, thickness of roof in roof coverings including ridges, hips, valleys and flashings complete all as specified and as directed.

S & F pre-painted Galvalume steel sheets of Trapezoidal profile having pitch 190mm, depth 29mm or Tiled Profile and thickness 0.50mm [Galvalume base-PPGL trapezoidal profile sheets], having tensile strength of 550 Mpa, fixed with aluminium self tapping screws, neoprene and EPDM washers of suitable size in roof covering complete all as specified and as directed. Note: Overlap shall be provided as specified by the manufacturer.

S & F pre-painted Galvalume steel Plain Sheets and thickness 0.50mm [Galvalume base-PPGL Sheets], having tensile strength of 550 Mpa, in ridges, hips, valley gutters, drip and straight flashing cut to length & bent to shape, girth sheets fixed with aluminium self tapping screws and neoprene and EPDM washers of suitable size in roof covering / cladding / eves trim / rake trim and closure trim / valley rain water gutter/ down spouts and top rafters etc. complete all as specified.

Dismantling of Wall & Ceiling Boards [Fibre / Pulp / Insulation etc] of any description or Insulation Boards / Slabs / Blankets including cover fillets complete all as specified and as directed.

S & F Solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame all as specified in Clause 8.B.6 and as shown on drawing on Page 180 of MES Schedule Part-II complete all as specified and directed.

S & F 5mm thick PVC sheet fillet of width 35mm, fixed on to wall as in PVC Frame work for wall paneling all as specified in Clause 8.B.6 and as shown on drawing on Page 180 of MES Schedule Part-II complete all as specified and directed.

S & F False Ceiling Frame Work using Anodised Aluminium snap grid frame work of 600 X 600 mm panel size for false ceiling with Aluminium "T" section of size 38 X 25 X 1.50 mm thick for Main Runners, 25 X 25 X 1.5 mm thick for Cross Runners and Angle of size 25 X 25 X 1.50 mm thick along the Walls suspended with and including 4 mm dia, Galvanized mild steel wire as in suspenders of ceiling members fixed in proper position complete all as specified.

S & F PVC laminated humidity resistant Gypsum ceiling tiles with MPL film, 8mm thick, 595mm x 595mm size, Edge Type- S/E, any design, Conforming to EN 520 & BS EN 13964-2014, fixed to frame work complete all as per manufacturer's instructions, as specified and as directed.

S & F Calcium Silicate False Ceiling at all heights in true horizontal level made out of Calcium Silicate Tiles of size 595 X 595 mm, having Integral densified reinforced edges of 15mm thickness all around with a collar of width 24mm and 10mm thickness at the centre of siliceous and calcareous material reinforced with cellulose fibre of approved texture, design and patterns, suspended on the Exposed Metal Frame Ceiling Grid of 600mm x 600mm size and applying one coat of Acrylic Washable Distemper and including suspended Exposed Inter-locking Metal Frame Work using GI Main "T" Runner of size 24x38mm, 0.33mm thick, spaced 1200mm centre to centre, Cross "T" of size 24X32mm, 0.33mm thick, 1200 mm long spaced between Main "T" at 600 mm centre to centre to form a grid of 1200X600 mm and secondary Cross "T" of 600mm long and of size 24X32mm, 0.33mm thick of the 1200x600mm panel to form grid of size 600x600mm, resting on periphery walls / partitions on GI Perimeter Wall Angle of size 24X24X3000 mm, 0.40 mm thick with the help of rawl plugs at 230mm centre to centre with 40mm long dry wall SS Screws including cutting/making opening for services like diffusers, grills, light fittings, smoke detectors etc., wherever required. Main "T" Runners shall be suspended from ceiling using galvanised mild steel [Galvanizing @ 80 Grams per Sq.m] 50 mm long, 8 mm outer diameter M-6 Dash Fasteners, 6 mm dia fully threaded hanger rod up to 1000 mm length and L-Shape level adjuster of size 85x25x25x2 mm, spaced at 1200mm centre to centre along Main "T". Bottom exposed width of 25 mm of all sections shall be pre-painted with polyester baked paint at all heights complete all as specified and as directed. Note :- The Size of frames and ceiling tiles specified in the description of item is minimum requirement, if the same size of section is not available, next higher size shall be provided by the contractor without any extra cost to the Department.

Dismantling of Floor, Hearth or Wall Tiling of any description including Cement Mortar bedding [but not backing] and removing serviceable tiles to the stores and removing rubbish / debris to a distance exceeding 1.5 KM but not exceeding 5 KM complete all as specified and as directed.

Demolition of Stone Slab laid, bedded and pointed in Cement Mortar of thickness and removing serviceable slabs to the stores and removing rubbish / debris to a distance not exceeding 1.50 KM complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment of soil under existing floors using chemical emulsion @ 1 litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 to match the existing floors complete all as specified and as directed.

M & L for 40 mm thick, PCC 1:2:4, Type B-0, using 12.5mm graded aggregate as in Damp proof course to horizontal or vertical surfaces including mixing water proofing compound as per manufacturers instructions complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for 100 mm thick, PCC 1:2:4, Type B-2, using 40 mm graded stone aggregate as in Sub base for flooring finished even and fair complete all as specified and as directed.

M & L for 75 mm thick, PCC 1:3:6, Type C-2, using 40 mm graded stone aggregate as in Sub base for flooring/ hardstanding finished even and fair complete all as specified and as directed.

M & L for 100 mm thick, PCC 1:2:4, Type B-2, using 40mm graded stone aggregate as in Floors / Hard standing etc, surface finished even and smooth with out using extra cement and spike rolling to surfaces or making impressions of expanded metal, while the concrete is green complete all as specified and as directed.

M & L for Forming Expansion Joint, 12mm thick, filled with Preformed Bituminous Filler and top 30mm Primed and sealed with Sealing Compound Grade "A" for 100mm thick flooring complete all as specified and as directed.

M & L for 75mm thick, PCC 1:3:6, Type C-1, using 20mm graded aggregate as in Plinth protection etc surface finished even and smooth with out using extra cement and providing 12mm thick joints for full depth of PCC at every 3.00 m and every change of direction duly filled with mastic filling comprising of 01 Part of heated bitumen blown grade of any penetration and 3 parts of sand [all by weight] complete all as specified and as directed.

M & L for 75 mm thick PCC 1:2:4, Type B-1, using 20mm graded aggregate as in Flooring/ hardstanding, surface finished even and smooth without using extra cement complete all as specified and as directed.

M & L for 40 mm thick PCC 1:2:4, Type B-1, using 20mm graded aggregate as in Flooring/ hardstanding, surface finished even and smooth without using extra cement complete all as specified and as directed.

M & L for 25 mm thick, PCC 1:2:4, Type B-0, using 12.5mm graded aggregate as in Sub base for flooring complete all as specified and as directed.

M & L for Vitrified Tiles, Double Charged, Coloured, Premium Quality, of size not exceeding 0.36 Sq.m, 9 to 10 mm thick as in Floors, set and jointed in cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Vitrified Tiles, Double Charged, Coloured, Premium Quality, of size not exceeding 0.36 Sqm, 9 to 10 mm thick as in Vertical Surfaces such as Skirting, Dado etc, set and jointed in cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Joint Free Glazed Ceramic Tiles, Edge Cut, Concept Type, Coloured, Premium Quality, of size 450 mm X 300 mm or 350 mm X 250 mm, 7 to 8 mm thick as in Vertical Surfaces such as Skirting, Dado etc. set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, of size exceeding 0.11 Sq.m and not exceeding 0.18 Sq.m, 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed.

M & L for Chequered Cement Concrete Tiles of size 300 X 300 mm, 25mm thick, Hydraulically pressed as in Floors, set jointed and pointed in neat cement slurry to match including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed.

M & L for machine cut Kota stone slab flooring using 20 to 25mm thick slabs, laid and jointed with grey cement slurry mixed with a admixture of pigment to match shade of slab including rubbing and polishing to smooth mirror finish all to required sizes, the size and design / pattern of slabs shall be as directed, including diagonals, inlays, borders, margins in two or more shades of slabs including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:6 complete all as specified and as directed.

M & L for Kota Stone Slabs of 20 to 25 mm thick as in Skirting, Dado, Risers of Steps, Jambs, Pillars etc. with machine cut edges, including diagonals, inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with Grey Cement [slurry] and jointed and pointed with grey cement slurry mixed with a admixture of pigment to match shade of Slabs, rubbing and grinding with mechanical equipment fitted with suitable grit size corborundum stones and polishing with Oxalic Acid to smooth, bright mirror finish over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: Single stone slab shall be used for entire height of skirting / dado / risers and joints shall match with the flooring.

M & L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red / Z Black / Pearl Black as in Floors, Treads of Steps, Window Cills, Cooking Platform etc., and the like with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabs including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: Single stone slab shall be used for entire Width and Length of Steps, Window Cills, Cooking Platform etc. and joints shall match with the flooring. The edges of treads shall be bull nosed / half rounded. The edges of the treads and landings shall also be provided with three Nos of grooves.

M & L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red / Z Black / Pearl Black as in Skirting, Dado, Risers of Steps, Jambs, Pillars, Wall Lining [Veneering to Wall] etc. with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including diagonals, inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabs over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: Single stone slab shall be used for entire height of Skirting / Dado / Risers and joints shall match with the flooring.

M & L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M & L for Inter Locking Paving Blocks of 60mm thick, made with M-35 Grade cement concrete using 20 mm graded stone aggregate, Hydraulically pressed of approved colour and pattern conforming to IS - 15658 set in floors complete all as specified and directed.

Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces etc including raking out joints, hacking for key scrubbing down with water etc and removing rubbish to a distance exceeding 1.5 KM but not exceeding 5 KM complete all as specified and as directed.

M & L for Cutting / Chipping the spalling concrete surfaces of Slabs, Beams, Columns, Fins, Facias, Parapets & Chajjas etc. and trimming, cleaning the surfaces of any thickness to receive Guniting / Plastering, preparing surfaces and applying a coat of Zinc rich epoxy primer to all steel surfaces as anti-rust agent and welding steel wire Fabric / Mesh of size 75X25mm of weight not less then 3.0KG per Sq.m to existing reinforcement, applying a coat of Nito Bond AR of M/s. Fosroc Chemicals or equivalent approved bonding agent in M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. as per manufacturer's instructions and providing pressure Guniting averaging 25mm thick at a pressure of not less than 6 KG / Sq.cm in Cement Mortar 1:3 duly modifying the mortar with and including suitable bonding agent of M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. @ 5% of weight of cement for sides and soffits of Slabs, Beams, Columns, Fins, Parapets Facias & Chajjas etc., finishing surface rough and finally rendering 15 mm thick in Cement Mortar 1:4 and finishing the top surface even and smooth without using extra cement conforming to proper geometrics including providing double scaffolding and safety measures as required and removal of the same on completion and disposal and depositing the demolished material to a distance exceeding 1.5 KM but not exceeding 5 KM complete all as specified and as directed.

M & L for Cutting / Chipping the spalling concrete surfaces of Slabs, Beams, Columns, Fins, Facias, Parapets & Chajjas etc. and trimming, cleaning the surfaces of any thickness to receive Guniting / Plastering, preparing surfaces and applying a coat of Zinc rich epoxy primer to all steel surfaces as anti-rust agent and welding steel wire Fabric / Mesh of size 75X25mm of weight not less then 3.0KG per Sq.m to existing reinforcement, applying a coat of Nito Bond AR of M/s. Fosroc Chemicals or equivalent approved bonding agent in M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. as per manufacturer's instructions and providing pressure Guniting averaging 30mm thick at a pressure of not less than 6 KG / Sq.cm in Cement Mortar 1:3 duly modifying the mortar with and including suitable bonding agent of M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. @ 5% of weight of cement for sides and soffits of Slabs, Beams, Columns, Fins, Parapets Facias & Chajjas etc., finishing surface rough and finally rendering 15 mm thick in Cement Mortar 1:4 and finishing the top surface even and smooth without using extra cement conforming to proper geometrics including providing double scaffolding and safety measures as required and removal of the same on completion and disposal and depositing the demolished material to a distance exceeding 1.5 KM but not exceeding 5 KM complete all as specified and as directed.

M & L for application of high build polymer modified cement mortar, 1:2½ mixed with 3 Litres of Nitobond SBR of M/s. Fosroc Chemicals India [P] Ltd. or its equivalent in M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s BOSTIk India Pvt. Ltd. per bag of cement in ceiling surfaces in two layers to form 10 to 20 mm thick even surface over a coat of bonding agent by mixing Nitobond SBR of M/s. Fosroc Chemicals India [P] Ltd. or its equivalent in M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s BOSTIk India Pvt. Ltd. @ 1 Litre + 1 Litre water + 3 KG cement complete all as per manufacturer's instructions.

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:4, including finishing the top surface even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 10 mm thick in Cement Mortar 1:6, including finishing the top surface even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering 5mm thick in cement mortar 1:4 including mixing water proofing compound as per manufacturers instructions over a backing coat of 10mm thick in CM 1:6 on concrete or brick masonry surfaces and finishing the top surface even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

Supply only integral water proofing compound [ISI marked] of approved make.

Hacking out old broken glass [any thickness, size, quality or description] from wooden frames including punching or drilling out old glazing pins / spring clips complete all as specified and as directed.

Hacking out old broken glass [any thickness, size, quality or description] from metal frames including punching or drilling out old glazing pins / spring clips complete all as specified and as directed.

S & F 4.8mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

M & L for Two coats of Acrylic washable Distemper by using auto roller/airless sprayer on newly plastered Wall surfaces over a coat of alkali resistant primer over two or more coats of Cement based Wall Care Putty on walls by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty including preparation of surfaces by using vacuum based sanding machine to obtain a smooth surface complete all as specified and as directed. Note:- The contractor shall carryout Distempering and allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering through their authorised applicators before commencement of the work to GE for approval.

M & L for Complete removal of existing treatment of any description on wall surfaces by using vacuum based sanding machine, removal of nails and applying upto 1mm thick Cement based Wall Care Putty on walls by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of Acrylic Washable Distemper by using auto roller/ airless sprayer over one of alkali resistant primer on wall surfaces complete all as specified and as directed. Note:- The contractor shall carryout Distempering & allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering & allied works through their authorised applicators before commencement of the work to GE for approval.

M & L for Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] by using auto roller/ airless sprayer over a Coat of Exterior Primer of same manufacturer as that of paint on newly plastered walls/ ceiling, pillasters, bands, borders, soffits of chajjas and projections including necessary preparation of surfaces by using vacuum based sanding machine complete all as specified and as directed. Note:- The contractor shall carryout Exterior Emulsion Painting and allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering through their authorised applicators before commencement of the work to GE for approval.

M & L for Complete removal of existing treatment of any description on wall surfaces by using vacuum based sanding machine and applying upto 1mm thick Cement based Wall Care Putty by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty on walls, pillasters, bands, borders, soffits of chajjas and projections including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] by using auto roller/ airless sprayer over one coat of exterior primer on wall surfaces complete all as specified and as directed. Note:- The contractor shall carryout Exterior Emulsion Painting and allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering through their authorised applicators before commencement of the work to GE for approval.

M & L for complete removal of existing treatment on wall surfaces and applying two coats of cement based paint over a coat of Alkali Resistant Primer complete all as specified and as directed.

M & L for one coat of Synthetic Enamel paint on old painted wooden surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for two coats of Synthetic Enamel paint on old painted wooden surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for two coats of synthetic enamel paint over one coat of pink primer to new wooden surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for one coat of Synthetic Enamel paint on old painted steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for two coats of Synthetic Enamel paint on old painted steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for Two coats of synthetic enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces not exceeding 10cm width or girth including necessary preparation of surfaces complete all as specified and as directed.

M & L for French polishing one or more coats on old polished wooden surfaces of any description over a coat of wood filler, over 10cm width or girth including necessary cleaning and preparing the surfaces complete all as specified and as directed.

S & F CPVC Pipes 25 mm outer diameter & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing, including taking down of existing unserviceable GI pipes complete all as specified and as directed.

S & F GI water tubing of 15 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

S & F GI water tubing of 20 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

S & F Rotational Moulded Polythene [HDPE] Water Tanks, Double Layered, ISI Marked, Cylindrical & Vertical Type 1000 Litres Capacity hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete all as specified and as directed.

S & F Ball Valve, PTMT, 20 mm dia, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule complete all as specified and as directed.

S & F Stainless Steel, Tubular Towel Rail, D Type, 600 mm long between flanges complete all as per Jaquar Catalogue No. ACN-1111SM or its equivalent in Kohler / Cera / Parryware / Prayag complete all as specified.

S & F Corner Glass Shelf with Bracket complete as per Jaquar Catalogue No. ACN-1173 or its equivalent in Kohler / Cera / Parryware / Prayag complete all as specified.

S & F in Health Faucet with 1 m long flexible tube, wall hook, non return valve complete as per Jaquar Catalogue No. ALD-577 or its equivalent in Kohler / Cera / Parryware / Prayag complete all as specified.

S & F Two way Bib Taps, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as per Jaquar Catalogue No. KUP-35041 PM or its equivalent in Kohler / Cera / Parryware / Prayag complete all as specified.

S & F Stainless Steel Toilet Paper Roll Holder, Chromium plated, Fancy type complete all as per Jaquar Catalogue No. AKP-35751P or its equivalent in Kohler / Cera / Parryware /Prayag complete all as specified.

S & F Stainless steel soap dispenser with glass bottle, Fancy type complete all as per Jaquar Catalogue No. AKP-35735P or its equivalent in Kohler / Cera / Parryware / Prayag complete all as specified.

S & F Pillar Taps, cast copper alloy, Chromium Plated, Fancy Type, 15 mm dia, with capstan head, screwed down high pressure with or with out lettered "Hot" or "Cold" with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as per Jaquar Catalogue No. CON-011KN or its equivalent in Kohler / Cera / Parryware / Grohe / Prayag complete all as specified.

S & F Angle Cock, 15 mm dia, concealed with wall flanges, brass, screwed down Chromium, high pressure with for iron pipe etc. complete all as per Jaquar Catalogue No. CON-053KN or its equivalent in Kohler / Cera / Parryware / Grohe / Prayag complete all as specified.

S & F Vitreous China Ware Wash Hand Basin, White, Flat Back of size 550 mm X 400 mm including 32mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible Waste Pipe, PVC Connection of 15mm Bore and 600mm long with PTMT check nut and union etc. complete all as specified and as directed.

S & F in repairs Vitreous China Wash Down Water Closet [Pedestal pattern], White, including 10 Litres capacity, PVC Valve less, Syphonic action type, low level flushing cistern, white, with inlet ball valve, float, handle, flush pipe of polyethylene of low or high density of PVC, 32mm dia including brackets and connections to pipe of Make Slimline or Cera or equivalent make and flush pipe including plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and 'P' or 'S' trap complete all as specified and as directed.

S & F Vitreous china urinal, bowl type, flat back, white of size 465 X 355 X 265mm, complete including providing and fixing plugs, bedding urinal against wall in cement mortar [1:2], securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, including 32mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, 32mm bore PVC flexible waste pipe, grating and union for discharge pipe, CP screws PVC Connection of PTMT, Chrome Urinal spreader fixed to 15 mm dia pipe etc. complete all as specified and as directed.

S & F 110mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls or laid in trenches including necessary brackets, clamps as required complete all as specified and as directed.

S & F 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls or laid in trenches including necessary brackets, clamps as required complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Bends of any radius with Access Door including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Bends of any radius including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Bends of any radius with Access Door including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Bends of any radius including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Vent Cowl including jointing with solvent cement complete all as specified and as directed.

S & F 75mm bore outlet PVC [SWR] Floor Trap with grating including jointing with solvent cement complete all as specified and as directed.

S & F in repairs Bib Taps, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type, Short Body with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as per Jaquar Catalogue No. CON CHR 037KN or its equivalent in Kohler / Cera / Parryware / Grohe Prayag complete all as specified.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel [½ round or ¾ section] in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required for 150 mm dia of pipe complete all as specified and as directed.

M & L for 150 mm dia RCC Pipes, Class NP2, laid and jointed with collars laid in trenches and jointed complete all as specified and as directed.

M & L for concrete bed to drain pipes of size 150 mm bore packing under and haunching against the sides of pipes after they are laid and fitted in cement concrete, Type C2, 1:3:6, using 40mm graded stone aggregate complete all as specified and as directed.

Taking down carefully existing unserviceable copper / aluminium point wiring [light, fan, socket or power] complete including fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings, etc and making good the disturbed surfaces all as per existing complete all as specified and as directed.

Taking down carefully existing unserviceable MCCB DBs, MCB DBs, SPN / TPN Enclosures including MCCBs, MCBs etc of any description and any capacity and making good the disturbed surfaces all as per existing complete all as specified and as directed.

Taking down carefully existing unserviceable Submain wiring of any description complete including wooden battens / conduits / casing capping and making good the disturbed surfaces all as per existing complete all as specified and as directed.

Taking down carefully existing unserviceable ceiling fans of any description and removing to stores including making good the disturbed surfaces all as per existing complete all as specified and as directed.

M & L for Point Wiring complete with 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, Two runs, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable, conforming to IS - 694 drawn through and including heavy duty PVC Conduit, 20 mm dia including all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type and Metal GI Flush Box of suitable size and thickness including Modular type Base / Grid Frame & Cover Frame for housing Modular Type Switches, Sockets and Regulators etc. concealed in walls, including 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable as earth continuity conductor with colour coding and connecting to Earth Dolly for One Light / Fan Point including cutting chases for concealing of pipes complete all as specified and as directed.

All as per Serial Item No. 167 above but One light point controlled by 2 Nos of Two way switch complete all as specified.

All as per Serial Item No. 167 above but One 3 Pin Switch Socket Outlet 5 Amps on Independent Board complete all as specified.

All as per Serial Item No. 167 above but One 3 Pin Switch Socket Outlet 5 Amps on same Board complete all as specified.

All as per Serial Item No. 167 above but one 15 Amps power point on independent board, with 1100 Volts, FRLS grade, 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable confirming to IS - 694 and including 1100 Volts, FRLS grade, 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable as Earth Continuity Conductor.

All as per Serial Item No. 167 above but one AC / Geyser point on independent board, with 1100 Volts, FRLS grade, 4.0 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable confirming to IS - 694 and including 1100 Volts, FRLS grade, 4.0 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable as Earth Continuity Conductor.

M & L for Sub main wiring with 2 runs of single core 2.5 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 20 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type including One run of 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor complete all as specified and as directed.. Note: 3 runs of 2.5 Sq.mm PVC insulated copper conductor cable & one run of 20 mm dia PVC Conduit will be measured as one unit

M & L for Sub main wiring with 2 runs of single core 4 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 25 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type including One run of 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor complete all as specified and as directed. Note:3 runs of 4 Sq.mm PVC insulated copper conductor cable & one run of 25 mm dia PVC Conduit will be measured as one unit

M & L for Sub main wiring with 2 runs of single core 6 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 25 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type including One run of 6 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor complete all as specified and as directed. Note:3 runs of 6 Sq.mm PVC insulated copper conductor cable & one run of 25 mm dia PVC Conduit will be measured as one unit

M & L for Sub main wiring with 4 runs of single core 10 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 40 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type including One run of 10 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor complete all as specified and as directed. Note: 5 runs of 10 Sq.mm PVC insulated copper conductor cable & one run of 40 mm dia PVC Conduit will be measured as one unit

S & F Switch, Modular Type, One Module, Single Pole, One Way, 6 Amps, 230 Volts complete all as specified and as directed.

S & F Switch, Modular Type, One Module, Single Pole, Two Way, 6 Amps, 230 Volts complete all as specified and as directed.

S & F Switch Modular type, one module, Single pole, One way, 16 Amps, 230 Volts complete all as specified and as directed.

S & F Socket Outlet, 3 Pin, 6 Amps, Modular Type, Two Modules, 230 Volts, complete all as specified and as directed.

S & F Socket Outlet, 3 pin, 16 Amps and 3 pin, 6 Amps, Modular Type, Two Modules, Multipurpose, 230 Volts complete all as specified and as directed.

S & F Electronic Fan Regulator, Stepped Type, Modular Type, Two Module, 120 W, AC, 230 Volts, Single Pole complete all as specified and as directed.

S & F Ceiling Rose, PVC body, 65 X 50 mm, Three Terminals, 230 Volts complete all as specified and as directed.

S & F SP & N Enclosure with 2 Pole and Earth Metal Plug & Socket for incorporating SP MCB complete including One MCB, SP, 20 Amps, 240 Volts complete all as specified and as directed.

S & F Telephone Socket / Jack with Shutter, RJ-11, Modular Type, 2 lines, including suitable Modular Type Pressed Metal Flush Box made out of 2mm thick MS Sheet, Modular type Base / Grid Frame & Cover Frame complete all as specified and as directed.

S & F TV Socket / Outlet, Co-Axial, Deluxe, Modular Type, One Module including suitable Modular Type Pressed Metal Flush Box made out of 2mm thick MS Sheet, Modular type Base / Grid Frame & Cover Frame complete all as specified and as directed.

S & F LAN Outlet, RJ 45, Modular Type, One Module, including suitable Modular Type Pressed Metal Flush Box made out of 2mm thick MS Sheet, Modular type Base / Grid Frame & Cover Frame complete all as specified and as directed.

S & F Heavy duty PVC Conduit, 20 mm dia concealed in Walls / Roofs / Floors / Ceiling etc. inclusive of boxes [Junction / Terminal but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. for drawing Coaxial TV Cable or Telephone Cable, LAN cables, etc complete all as specified

S & F MCB DB, TPN, 4 Way, 415 Volts, with DIN Channel, Double Door with 200 Amps rated bus bar suitable for mounting MCBs, flush mounted with wall complete all as specified and as directed.

S & F MCB DB, SPN, 8 Way, 240 Volts, with DIN Channel, Double Door with 200 Amps rated bus bar suitable for mounting MCBs, flush mounted with wall complete all as specified and as directed.

S & F MCB, TPN, 63 Amps, 10 KA, 'C' Curve, AC, 415 Volts, 50 Hz complete all as specified and as directed.

S & F MCB, TP, 40 Amps, 10 KA, 'C' Curve, AC, 415 Volts, 50 Hz complete all as specified and as directed.

S & F MCB, SPN, 40 Amps, 10 KA, 'C' Curve, AC, 415 Volts, 50 Hz complete all as specified and as directed.

S & F MCB, SPN, 6 - 32 Amps, 10 KA, 'C' Curve, AC, 415 Volts, 50 Hz complete all as specified and as directed.

S & F MCB, SP, 6 - 32 Amps, 10 KA, 'C' Curve, AC, 230 Volts, 50 Hz complete all as specified and as directed.

S & F DLP PVC adaptable Trunking System complete of size 100 X 100 mm including base, covers, partitions, trunking, body joint cover, all finishing accessories and mounting wiring accessories, end caps, T Bend, Flat Angle, Internal and External Bends including arranging of existing cables, refrigerator pipes, etc and making good disturbed surfaces complete all as specified and as directed.

S & F DLP PVC adaptable Trunking System complete of size 75 X 75 mm including base, covers, partitions, trunking, body joint cover, all finishing accessories and mounting wiring accessories, end caps, T Bend, Flat Angle, Internal and External Bends including arranging of existing cables, refrigerator pipes, etc and making good disturbed surfaces complete all as specified and as directed.

S & F Surface & wall mounted Energy efficient LED Tube Light Fitting, of not less than 2000 Lumens output, 4 feet long, 5700 K of cool white, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Surface & wall mounted Energy efficient Sleek LED Mirror Light Fitting of not less than 1000 Lumens, 2 feet long, with Acrylic / PMMA diffuser for soft glare free light with all accessories internally prewired and including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Square recessed mounted Flat Panel LED Ceiling Light suitable for fixing in 2' X 2' Grid False Ceiling of not less than 3600 Lumens output,, 6500 K, with high transmitive diffuser for soft-light and glare free symmetrical illumination with all accessories internally prewired and including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm including taking down existing light fittings of any description and making good the disturbed surfaces to match with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Energy efficient & Long life Street Light Luminaire, of not less than 3000 Lumens output, 5700 K with Pressure Die Cast Aluminium Housing, IP66 protection, heat resistant glass cover, high power LEDs as light source, electronic driver including GI Bracket made out of 32 mm bore GI Tube, Medium Grade of size not exceeding 1.50 m in length and bent to shape required and fixed with 2 Nos of Pole fitting Clamps made out of MS Flat of size 50 X 6mm, bolts, nuts, washers and painting with two coats of aluminium paint over a coat of primer red oxide zinc chrome primer and connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

Fixing only serviceable light fittings of any description and in any position including connecting up with new three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed.

S & F Energy efficient, Low Noise, Ceiling Fan, 1200mm Sweep of any colour as approved, 03 blades, BEE 5 Star Rated, with BLDC Motor, Copper Wound, 350 RPM, with Double Ball Bearing, Conforming to IS - 374, ISI Marked, suitable for operation on Single Phase, 240 Volts, AC, 50Hz, including Down Rod, Canopies, Shackles, Safety Rope, Hanging Clamps, Bushes, having P.F >0.95, Service Value >6.5, Air Delivery >215 CMM, Power Consumption less than 35 Watt, THD less than 5% including provision of Electronic speed control Regulator step type, including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Ceiling Fan shall be provided with 03 Years onsite replacement warranty. Rate quoted is deemed to be including the same and nothing shall be paid extra on this account.

Taking down Ceiling Fan of any description from its position and refixing the same after repairs to buildings, at same place or at new place including connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm, cleaning, greasing etc and replacement of Spares such as Capacitor 4 Mfd, Bearings, Shaft Bushes, Condenser, Rubber Bushes, Nuts & Bolts etc. and also including cleaning, greasing and spray painting with two coats of synthetic enamel paint of approved colour over a coat of zinc chrome primer after filling cavities with filler and complete all as specified and directed. Note: The rate of necessary cutting chases in wall and making good the disturbed surfaces to match with existing shall be deemed to have been included in unit rate quoted.

S & F Wall Mounted Air Circulator Fan, 600mm Sweep, Metal Body, Heavy duty with double ball bearing, low noise, Copper wound, 1400 RPM, Air Delivery not less than 270 Cum/min, wattage consumption not more than 200 watts, 230 Volts, AC, 50 Hz, Conforming to IS, Wall Mounting Type complete with wall bracket and mounting accessories kit complete all as specified and as directed.

Supplying, installing, testing and commissioning of 5 Star rated Hi-Wall Split Units Indoor / Outdoor with Cordless Remote Control Unit and with in-built advanced Air Ioniser and Plasma Filters for better indoor air quality with latest Inverter technology, having Eco friendly Refrigerant Gas, Copper Condenser Coil, EER 3.2 of Capacity 1.5 TR, Summer Cool, Dual Rotor Inverter Compressor, Automatic 4D Swing Copper Condenser, BLDC Motor, necessary copper pipe connections including cutting, bending, brazing, insulation on pipe etc, PVC Drain Pipe, electric connection between indoor and outdoor unit with suitable size PVC insulated, multi-stranded copper cable complete all as specified and as directed. Make: Blue Star / Hitachi / Daikin / Carrier / Voltas Note: The rate quoted by the contractor is deemed to include for Powder Coated Mild Steel Fixing Brackets for Outdoor and Indoor Units at any height and Copper tube of suitable size upto 5m length and Drain Pipe made of High Density Polyethylene Pipes [HDPE] of pressure rating 6 KGf / Sq.cm of 25mm dia upto 5m length.

S & F Electronic wall mounted time delay Voltage stabilizer of 4 KVA Capacity, Automatic Operation, for input variation of 170 Volts to 250 Volts with stabilised voltage of 230 Volts with accuracy of ± 2.5% complete all as specified. Make: V Guard/ Servo/ Kee Line

S & F 1/2" dia Copper Pipe of wall thickness 1mm, suitable for Split type Air conditioners and connecting between Indoor and Outdoor unit including fixtures complete all as specified and directed.

S & F 1/4" dia Copper Pipe of wall thickness 1mm, suitable for Split type Air conditioners and connecting between Indoor and Outdoor unit including fixtures complete all as specified and directed.

S & F UPVC Heavy Duty pipe of 205mm dia as in Drain Pipe complete with necessary elbows, tees, reducers, brass connector between GI and PVC Pipe etc. including necessary supports, fittings, joints wherever required complete all as specified and as directed.

Supplying, laying and testing XLPE insulated and PVC sheathed, FRLS, armoured heavy duty underground cable, ISI marked with aluminium stranded conductor 1100 Volt grade of size 4 Core, 16 Sq.mm cross section suitable for earthed system, laying in trenches / duct / fixed to poles / drawn through pipes / sleeving through pipe in duct, including suitable size Double compression copper stainless steel cable gland, crimping type cable lugs, sockets etc. complete all as specified and as directed.

Earthing complete with Galvanised Steel Earth Plate Electrode 600 X 600 X 6 mm thick burried directly in ground [earth pit not less than 2.25 m deep below ground level] with top edge of Plate not less than 1.50 m below normal ground level connected to 4 mm GI Wire [Earth Lead] and GI pipe 15 mm, Medium Grade for earthing lead protection to the extent of maximum 7.5m, Earth Plate Electrode surrounded by 150mm thick packed layers of Charcoal and Common Salt filled in alternate layers, connected to the Plate by means of GI Bolts & Nuts complete all as per Electrical Plate No. 3 of SSR Part – I, connected to panel / DB including testing on completion including main earthing, Charcoal, Common Salt, PCC [1:2:4, Type B1] Pit with RCC 1:2:4, Type B1 Cover, 50 mm thick with 6 Nos, 8 mm dia TMT bars in both ways, MS frame made with 40 X 40 X 6 mm Angle Iron, MS Funnel with 20 mm bore, medium grade GI Watering pipe, wire mesh, earth work excavation, return filling, removal of surplus soil etc. complete all as specified and as directed.

N Sydeswara Rao

AADHITYA ASSOCIATES

M B CONSTRUCTIONS

TECHNO SOFT SOLUTIONS

V R K CONSTRUCTIONS

CIVILEC ENGINEERING WORKS

ARCHANA ENGINEERING ENTERPRISES