Drilling of 63mm Dia Bore well and laying of 32mm dia GI Surface lines at Scavengers Colony in Ward No. 33 Under Zone-II .(3rd Call).

Drilling of tube/Bore wells by down the hole hammer to a finished diameter of 163mm dia in all formations/stratas such as medium hard rock formation, consolidation formation etc, including drilling in over burdern soils to a diameter of not less than 200mm includingsertion of 180mm diameter including the insetion of unplasticized PVC pipe confirming to IS specification No:4965/11988 with ISI mark up to a depth as directed by the department and flusing 8 hours for Bore development conducting yield test including transportation of drilling rigs spporting vehicles including crew charges and all other charges as required etc., complete all done to the satisaction of department and as stipulated in the technical specification enclosed to this schedule but excluding the cost of PVC casing pipes, coupling and cap, the entire work should be carried out as per IS 2800 part I and II/1979. The rate is execlssive of all taxes in rural and urban ares rate as per (Rate as per SE RWS RC rates)

for Deepening 1 to 90mts

for Deepening 90 to 150mts

for Deepening 150 to 250mts

Supply and delivery of 250mm dia meter PVC pipes with working pressure of 6Kg/ Sqcm as casing pipe for bore wells confirming to IS Specification No. 4958/1988 with ISI mark including all taxes and duties etc., complete

Supply and delivery of 180mm dia meter PVC pipes with working pressure of 6Kg/ Sqcm as casing pipe for bore wells confirming to IS Specification No. 4958/1988 with ISI mark including all taxes and duties etc., complete

Supply and fixing of PVC bore cap suitable for 180mm dia PVC pipe used for fore wells

Supply and Transportation of 5 to 10.. 5 star rated 5 HP submersible motor pumpset confirms to IS 8034 & mortor conforming to IS:9283 with water proof winding, pump shal be suitable various delivery head and discharge with stainless steel soft mortor suitable for working on 415 V +- , three phase 50HZ Ac Supplied Etc., complete 4 inches bore well Makes: Kirloskar / Crompton / Texmo / CRI / KSB/Lubi (ELEC 5.4.6)

Fabrication , transportation and supply of suitable size panel board for single phase submersible motor up to 1.5 HP consisting of relay, Contactor, starting and running capacitors, Voltmeter, Ammeter, indicator lamps, MCB , on/off switch including supply and fixing of DOL starter of make S/LTLK/Seimens/BCH/Crompton. complete.,(MAT - 03712, LEC - 5.4.16)

Supply of 3 Core 4.0 Sq.mm..ISI marked, PVC insulated and sheathed FRLS/FRLS-H round copper cable for voltage up to 1100V as per IS 694/1990. Makes: As per list of recommended brands as category I (MAT - 02774)

Supply of …10Sq.mm…...ISI marked WPSC (Weatherproof Single Core) ISI Aluminum Wire. Makes: As per list of recommended brands. (MAT-02790)

Provisition for Geological Charges

Supply and fixing of 40 and 32mm dia nominal Bore GI pipe medium grade properties and weight asper IS1239 ISI mark with GI fittings including cost of pipe and its fittings and labour charges etc complete excluding Taxes

32mm dia GI Pipe

40mm dia GI Pipe

Supply and Delivery of GI pipes and Specials including cost and conveyance of all materials labour charges etc., complete.

40mm dia GI long Couplings

40mm dia GI Bends

40x32mm dia GI Reducer

32mm dia GI Couplings

32mm dia GI Unions

32mm dia Elbows

32mm dia X-Nipples

32x32x15mm dia GI Tees

15mm x 12' (1feet ) GI Pipe Nipples

15mm dia GI Couplings

15mm dia CI Taps

15mm dia GI Bends

32mm dia End Caps

32mm dia GM Gate Valves (Zoloto Make)

GI Pipe Threads

Chellock & Twine

Engaging of Plumber on daily wages for laying of GI Surface pipe line including cost of all labour charges etc., complete.

Engaging of 7 cum Air Compressior for Dismantling of Steps, CC Ramps. CC Road Crossings etc., including cost of fuel and wages for helper all charges etc., complete.

Provisition for Erection of Servece Meter and Servece line including cost of all labour charges etc., complete.

Transportation of GI pipes from Godown to lathe shop for threading and lathe shop to work spot including cost and conveyance of all labour charges etc., complete.