Construction of Rajya Atithi Grah at Rudrapur, District -Udham Singh Nagar

Amount

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. :All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

P/L cement concrete - all works upto plinth level : 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

P/L cement concrete - all works upto plinth level : 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for :Suspended floors, roofs, landings, balconies and access platform.

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, griders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for : Columns, pillars, piers, abutments, posts and struts

Centering and shuttering including strutting, propping etc. and removal of form for : Stairs, (excluding landings) except spiral-staircases

Centering and shuttering including strutting, propping etc. and removal of form for : Weather shade, Chajjas, corbels etc., including edges

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified mininum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. 5.33.1 All works upto plinth level. Concrete of M30 grade with minimum cement content of 350 kg /cum

All works above plinth level upto floor V level. Concrete of M30 grade with minimum cement content of 350 kg /cum. columns, pillars piers etc.

All works above plinth level upto floor V level. Concrete of M25 grade with minimum cement content of 330 kg /cum. lintel beams and girders etc.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked Bright finished M.S. fitting for door windows.250x16x5 mm sliding door bolts

Providing and fixing ISI marked Bright finished M.S. fitting for door windows.250x10 mm Tower bolt

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :

Providing and fixing ISI marked Bright finished M.S. fitting for door windows.150x10 mm Tower bolt

Providing and fixing ISI marked Bright finished M.S. fitting for door windows.125 mm handles

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing bright finished brass night latch of approved quality including necessary screws etc. complete.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Sal wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately, Second class teak wood, 35 mm thick shutters

Providing and fixing factory UPVC WINDOW FENISTA MAKE W1, (4.20X2.45)

Providing and fixing factory UPVC WINDOW FENISTA MAKE W2, (3.70X2.45)

Providing and fixing factory UPVC WINDOW FENISTA MAKE W3, (3.67X2.45)

Providing and fixing factory UPVC WINDOW FENISTA MAKE W4, (3.05X2.45)

Providing and fixing factory UPVC WINDOW FENISTA MAKE W4a (2.97X2.45)

Providing and fixing factory UPVC WINDOW FENISTA MAKE W5 (2.45X2.45)

Providing and fixing factory UPVC WINDOW FENISTA MAKE W6 (2.42X1.53)

Providing and fixing factory UPVC WINDOW FENISTA MAKE W7 (1.82X2.45)

Providing and fixing factory UPVC WINDOW FENISTA MAKE W8 (1.77X2.45)

Providing and fixing factory UPVC WINDOW FENISTA MAKE V, (1.52X0.92)

Providing and fixing factory UPVC WINDOW FENISTA MAKE V2, (0.925X0.925)

Providing and fixing factory UPVC WINDOW FENISTA MAKE V3, (0.75X0.925)

Providing and fixing factory UPVC WINDOW FENISTA MAKE W1(1.52MX1.50M)

Providing and fixing factory UPVC WINDOW FENISTA MAKE W2 (1.22MX.88M)

Providing and fixing factory UPVC WINDOW FENISTA MAKE V1 (0.925MX0.925M)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Sal wood

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi- etallic contacts, all complete to perform as per Specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as pecified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Area of slab over 0.50 sqm

Providing and laying Italian stone flooring BASIC COST400 SQFT STONE

Extra for italian stone flooring in treads of steps and risers using single length up to 2.00 metre.

6 mm cement plaster of mix : (1 cement : 3 fine sand)

12 mm cement plaster: 1:6 (1 cement : 6 fine sand)

15 mm cement plaster: 1:6 (1 cement : 6 fine sand)

Applying priming coat : With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Applying priming coat : With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer.

French spirit polishing : Two or more coats on new works including a coat of wood filler

Providing and fixing GI Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing ‘C’ wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of GI steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets.Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring ‘T’ with : GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holesand having NRC of 0.5, electro statically polyester powdercoated of thickness 60 microns (minimum), including factory painted after bending and perforation.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase

52 mm thick cement concrete flooring with concrete hardener topping, underlayer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 gradedstone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardenerconsisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mmnominal size) by volume, hardening compound mixed @ 2 litre per 50 kg ofcement or as per manufacturer's specifications. This includes cost of cementslurry, but excluding the cost of nosing of steps etc. complete.

Supplying and stacking at site. 63 mm to 45 mm size stone aggregate

Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D4956-01 in blue and silver white or other colour combination including subjectmatter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pastedon substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-charge.Mandatory/ Regulatory sign boards of 900 mm diametre with support length of 3750 mm

Providing and laying 60mm thick faciory made cement concrete interlocking paverblock of M -30 grade made by block making machine with strong vibratorycompaction, of approved size, design & shape, laid in required colour and patternover and including 50mm thick compacted bed of coarse sand, filling the jointswith line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25grade cement concrete in position to the required line, level and curvature, jointedwith cement mortar 1:3 (1 cement: 3 coarse sand), including making joints withor without grooves (thickness of joints except at sharp curve shall not to morethan 5mm), including making drainage opening wherever required complete etc.as per direction of Engineer-in-charge (length of finished kerb edging shall bemeasured for payment). (Precast C.C. kerb stone shall be approved by Engineerin-charge).

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber,applying and brooming requisite type of screening / binding material to fill upinterstices of coarse aggregate, watering and compacting to the requireddensity .

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarsesand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tiling with cement mortarwhich will be paid for separately (for the purpose of measurement the entire treated surface will be measured)

Grading roof for water proofing treatment with Cement mortar 1:3 (1 cement : 3 coarse sand)

Supplying and fixing C.I. cover with frame for manholes :455x610 mm rectangular C.I. cover (light duty)the weight of the cover to be not

Horticulture & Landscaping (2018) Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 mm

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Providing and Displaying Bismarckia Palm 115 to 180 cm ht., well developed 12 and above good color fresh and healthy leaves in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Alpinia Variegated (three in one) having ht. 30 cm and above, with fresh and healthy variegated foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge..

Providing and stacking of Ficus benjamina (green) of height 150-165 cm., bushy with healthy branches and lush green foliage in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Fishtail palm of ht. 150-180 cm bottom girth 15- 20 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Ficus panda of height 60-90 cm, with 8-10 branches, and healthy foliage, bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Hibiscus rosasinensis of height 90-105 cm., bushy in big size HDPE bag as per direction of the officer-in-charge.

Seeding and Mulching Preparation of seed bed on previously laid top soil, furnishing and placing of seeds, fertilizer, mulching material, applying bituminous emulsion @ 0.23 litre per sqm and laying and fixing jute netting, including watering for 3 months all as per Technical Specification Clause 310.

Trimming of grass and weeds from the shoulders/berms and disposing off the same to suitable locations as per technical specifications Clause 1914

PLUMBING WORKS Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Coupler 75 mm.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Coupler 110 mm.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 75 mm bend

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 110 mm bend

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 20 mm dia

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.External work 20 mm dia nominal bore

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :20 mm nominal bore

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.20 mm nominal bore, 120 mm long, weighing not less than 198 gms

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing PTMT bib cock of approved quality and colour. 15mm nominal bore, 86 mm long, weighing not less than 88 gms

Providing and fixing PTMT stop cock of approved quality and colour. Concealed stop cock, 15 mm nominal bore, 108 mm long, weighing not less than 108 gms

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : 17.5.1 Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc.Complete as per standard design ine. Inside dimensions 455x610 mm and 45 cm deep for single pipe line.

Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets

Wall hung type European Water Closet: Providing Fixing wall hung type white vitreous china European Water Closet, white vitreous china flushing cistern of approved make with seat and lid (heavy duty) brass hinges, including C.I.chair or other hanging arrangement complete with rubber buffer having 'P' or 'S' trap, PVC pan connector, including C.P. Nuts, bolts, etc. making holes in walls, floors and making good the same.KOHLER Cat.N20218IN

Providing Fixing wall hung type white vitreous china European Water Closet, white vitreous china flushing cistern of approved make with seat and lid (heavy duty) brass hinges, including C.I.chair or other hanging arrangement complete with rubber buffer having 'P' or 'S' trap, PVC pan connector, including C.P. Nuts, bolts, etc. making holes in walls, floors and making good the same.KOHLER Cat.N5573IN-2-0

Providing Fixing, testing and commissioning of C.P. brass health faucet with plastic flexible pipe of 1.5mtrs and built in control, wall hooked complete as required..KOHLER Cat.N 12927IN-CP

Providing Fixing, testing and commissioning of white vitreous china flat back urinal large (Semistall) of size 590x375x390mm with C.I. hangers and 15mm dia C.P. spreader, 32mm dia cast bottle trap and pipe to wall with C.P. flange complete including cutting and making good the walls and floors wherever required. KOHLER Cat.No. K-4978IN-ER-0

Providing Fixing, testing and commissioning of Urinal automatic flushing system comprising of infra-red photocell electrically operated soleniod valve with concealed copper wiring, plumbing, electronic and electrical accessories including such items as will be required to provide satifactorily functioning of system as approved by Engineer-in-charge. The system shall fluch the urinal after use automatically. The flushing mechanism to match urinal used in above item No. KOHLER Cat.No. K-8791T-C01-CP

Providing Fixing , testing and commissioning of white vitreous china urinal partition of size 680x300 mm fixed with expandable anchor fasteners with C.P. brass bolts and washers,embeddded in wall with anchor and set in concrete complete including cutting and making the walls wherever required.

Providing Fixing in position best quality Indian make recessed type toilet paper holder complete in all respects including cutting and making good the walls etc. (Jaquar AHS-1553) Providing Fixing C.P. brass toilet paper holder.

Providing Fixing, testing and commissioning of vitreous china above/under counter mounted type oval / circular wash basin 550x400mm size with 32mm C.P. brass waste assembly, 32mm C.P. bottle trap with extension piece, wall flanges and rubber adapters for waste connection complete including C.I. / M.S. fabricated adjustable brackets duly painted cutting and making good the walls / fllor wherever required. KOHLER Cat.No. K-5373IN-0

Providing Fixing, testing and commissioning of vitreous china above/under counter mounted type oval / circular wash basin 550x400mm size with 32mm C.P. brass waste assembly, 32mm C.P. bottle trap with extension piece, wall flanges and rubber adapters for waste connection complete including C.I. / M.S. fabricated adjustable brackets duly painted cutting and making good the walls / fllor wherever required. KOHLER Cat.No. K28784IN-0

Providing Fixing stainless steel sink with M.S. galvanised or C.I. Painted brackets C.P. brass bottle trap and pipe towards wall with C.P. wall flange and rubber adopter for waste connect painted including painting the fittings and cutting and making the good the walls whereever required. Kitchen Sing Single Bowl with Board (953x470 mm SIZE) Cobra Sink) Model No Kaveri (SBD) IS No 199831/1984

Providing Fixing stainless steel sink with M.S. galvanised or C.I. Painted brackets C.P. brass bottle trap and pipe towards wall with C.P. wall flange and rubber adopter for waste connect painted including painting the fittings and cutting and making the good the walls whereever required. 1 No. each C.P. brass wall mounted sink mixer with swinging casted spout for hot and cold water supply flow should be regulate 5 LPM with areator.(jaquar FLR 5309N

Providing Fixing stainless steel sink with M.S. galvanised or C.I. Painted brackets C.P. brass bottle trap and pipe towards wall with C.P. wall flange and rubber adopter for waste connect painted including painting the fittings and cutting and making the good the walls whereever required. Pvc Bottle Trap 40mm dia

Providing Fixing towel rail of approved make including providing and Providing Fixing C.P. brass screws, making holes in wall and making good. (Jaquar AKB-35711) Size 600 mm x 20 mm dia.

Providing Fixing 15mm C.P. brass angle valve with nuts, washer and brass flange complete, including cutting and making good the wall wherever required. KOHLER Cat.No. K-80154IN-4AV-CP

Providing Fixing C.P. brass air purifier fixed to wooden cleats with C.P. brass screws complete.

Providing Fixing solid state fully hygienic no touch hand drier of approved make rated for continuous repeat usage with solid state time delay LSF protection, with independent ambient light level and seasonal control temperatures including providing necessary CI/MS brackets painted with two or three coats of enamel paint of approved shade over a coat of primer, wiring cables from drier to plug, plug tops etc. complete including cutting and making good the walls wherever required.

Providing Fixing C.P. brass shower/diverter 73040 k

Providing Fixing C.P. brass shower/diverter 73199

Providing Fixing pressure type liquid soap dispensor with C. P. brass lid and brackets fixed to raul plug with C. P. brass screws and glass container complete in all respect. (Jaquar 35735)

Providing and fixing automatic high pressure electric water heaters or equivalent make with glass lining thermostats with each element and high temperature cut off, necessary insulation, safety valve, etc. all complete.Make AO Simit

Providing, fixing, testing and commissioning uPVC pipe SWR Pipe for internal soil and waste drainage system conforming to IS:13592 Type 'B' for soil waste, vent and rain water drainage pipe including injection moulded fittings e.g. tees, bends, clamps, Y junctions, reduces couplings, adapters, door bend and terminal cowl etc. jointing with rubber ring/ solvent cement including cuttings the walls and floor as required and making good the walls and floors as required at site.75 OD

Providing, fixing, testing and commissioning uPVC pipe SWR Pipe for internal soil and waste drainage system conforming to IS:13592 Type 'B' for soil waste, vent and rain water drainage pipe including injection moulded fittings e.g. tees, bends, clamps, Y junctions, reduces couplings, adapters, door bend and terminal cowl etc. jointing with rubber ring/ solvent cement including cuttings the walls and floor as required and making good the walls and floors as required at site.110 OD

Providing, fixing, testing and commissioning uPVC pipe SWR Pipe for internal soil and waste drainage system conforming to IS:13592 Type 'B' for soil waste, vent and rain water drainage pipe including injection moulded fittings e.g. tees, bends, clamps, Y junctions, reduces couplings, adapters, door bend and terminal cowl etc. jointing with rubber ring/ solvent cement including cuttings the walls and floor as required and making good the walls and floors as required at site.160 OD

Providing and fixing injection moulded SWR 'P' or 'S' floor trap of self cleansing design with deep seal of 50mm including cost of cutting and making good walls and floors. The jointing of pipes to the floor trap is to be completed with solvent cement wherever required complete in all respect. 110 x 110 mm

Providing, fixing 110 mm dia. uPVC saddle fittings approximately 150 - 300 mm long above the trap with one or more 32/40/50 mm dia. inlets complete in all respects.

Providing, fixing, jointing with solvent cement, testing and commissioning of unplasticised rigid PVC (Class-III) pipes conforming to IS: 4985 including all fittings such as bends, clamps, cowls, cleanout plug, supports etc., cost of cutting holes in walls and floors and making good the same and complete as required for waste connection to FT. (Nothing extra to be paid on account of fittings).Working pressure = 6kg./Sq.cm, 25 OD

Providing, fixing, jointing with solvent cement, testing and commissioning of unplasticised rigid PVC (Class-III) pipes conforming to IS: 4985 including all fittings such as bends, clamps, cowls, cleanout plug, supports etc., cost of cutting holes in walls and floors and making good the same and complete as required for waste connection to FT. (Nothing extra to be paid on account of fittings).Working pressure = 6kg./Sq.cm, 32OD

Providing, fixing, jointing with solvent cement, testing and commissioning of unplasticised rigid PVC (Class-III) pipes conforming to IS: 4985 including all fittings such as bends, clamps, cowls, cleanout plug, supports etc., cost of cutting holes in walls and floors and making good the same and complete as required for waste connection to FT. (Nothing extra to be paid on account of fittings).Working pressure = 6kg./Sq.cm, 40 OD

Providing and fixing PVC clean out plug & FCO with suitable opening arrangement for cleaning the pipe complete in all report. 110 OD COP

Providing and fixing PVC clean out plug & FCO with suitable opening arrangement for cleaning the pipe complete in all report. 110 OD FCO

Providing and fixing stainless steel cockroach trap with built-in stainless steel squar grating of size 153 x 153mm.

Providing, fixing, jointing and testing in position heavy duty (conforming to IS : 1239) galvanized iron pipes with screwed socket joints and necessary galvanized iron fittings and special such as sockets, back nuts, elbows, bends, tees, reducers, enlargers, plugs, unions, clamps, etc. including necessary excavation, backfilling, fixing with clamps, drilling holes in walls, slabs, hydraulic testing for tube well, irrigation, City water supply and making good the same complete in all respectas as per specifications (For External work). Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.Internal work - Exposed on wall. 15 mm dia

Providing, fixing, jointing and testing in position heavy duty (conforming to IS : 1239) galvanized iron pipes with screwed socket joints and necessary galvanized iron fittings and special such as sockets, back nuts, elbows, bends, tees, reducers, enlargers, plugs, unions, clamps, etc. including necessary excavation, backfilling, fixing with clamps, drilling holes in walls, slabs, hydraulic testing for tube well, irrigation, City water supply and making good the same complete in all respectas as per specifications (For External work). Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.Internal work - Exposed on wall. 20 mm dia

Providing, fixing, jointing and testing in position heavy duty (conforming to IS : 1239) galvanized iron pipes with screwed socket joints and necessary galvanized iron fittings and special such as sockets, back nuts, elbows, bends, tees, reducers, enlargers, plugs, unions, clamps, etc. including necessary excavation, backfilling, fixing with clamps, drilling holes in walls, slabs, hydraulic testing for tube well, irrigation, City water supply and making good the same complete in all respectas as per specifications (For External work). Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.Internal work - Exposed on wall. 25 mm dia

Providing, fixing, jointing and testing in position heavy duty (conforming to IS : 1239) galvanized iron pipes with screwed socket joints and necessary galvanized iron fittings and special such as sockets, back nuts, elbows, bends, tees, reducers, enlargers, plugs, unions, clamps, etc. including necessary excavation, backfilling, fixing with clamps, drilling holes in walls, slabs, hydraulic testing for tube well, irrigation, City water supply and making good the same complete in all respectas as per specifications (For External work). Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.Internal work - Exposed on wall. 32 mm dia

Providing, fixing, jointing and testing in position heavy duty (conforming to IS : 1239) galvanized iron pipes with screwed socket joints and necessary galvanized iron fittings and special such as sockets, back nuts, elbows, bends, tees, reducers, enlargers, plugs, unions, clamps, etc. including necessary excavation, backfilling, fixing with clamps, drilling holes in walls, slabs, hydraulic testing for tube well, irrigation, City water supply and making good the same complete in all respectas as per specifications (For External work). Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.Internal work - Exposed on wall. 40 mm dia

Providing, fixing, jointing and testing in position heavy duty (conforming to IS : 1239) galvanized iron pipes with screwed socket joints and necessary galvanized iron fittings and special such as sockets, back nuts, elbows, bends, tees, reducers, enlargers, plugs, unions, clamps, etc. including necessary excavation, backfilling, fixing with clamps, drilling holes in walls, slabs, hydraulic testing for tube well, irrigation, City water supply and making good the same complete in all respectas as per specifications (For External work). Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.Internal work - Exposed on wall. 50 mm dia

Providing, fixing, jointing and testing in position heavy duty (conforming to IS : 1239) galvanized iron pipes with screwed socket joints and necessary galvanized iron fittings and special such as sockets, back nuts, elbows, bends, tees, reducers, enlargers, plugs, unions, clamps, etc. including necessary excavation, backfilling, fixing with clamps, drilling holes in walls, slabs, hydraulic testing for tube well, irrigation, City water supply and making good the same complete in all respectas as per specifications (For External work). Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.Internal work - Exposed on wall. 65 mm dia

Providing and fixing brass ball valves with SS stem and ball compele complete in all respects (teasted to 10 kg/sq. cm pressure ) as per specifications.15 mm dia

Providing and fixing brass ball valves with SS stem and ball compele complete in all respects (teasted to 10 kg/sq. cm pressure ) as per specifications.20 mm dia

Providing and fixing brass ball valves with SS stem and ball compele complete in all respects (teasted to 10 kg/sq. cm pressure ) as per specifications.25 mm dia

Providing and fixing brass ball valves with SS stem and ball compele complete in all respects (teasted to 10 kg/sq. cm pressure ) as per specifications.32 mm dia

Providing and fixing brass ball valves with SS stem and ball compele complete in all respects (teasted to 10 kg/sq. cm pressure ) as per specifications.40 mm dia

Providing and fixing brass ball valves with SS stem and ball compele complete in all respects (teasted to 10 kg/sq. cm pressure ) as per specifications.50 mm dia

Providing and fixing brass ball valves with SS stem and ball compele complete in all respects (teasted to 10 kg/sq. cm pressure ) as per specifications.65 mm dia

Earth work in excavation for pipe trenches of required width including excavation for sockets, dressing of sides, ramming of bottoms, including shoring, dewatering, disposal of the excavated material, refilling the soil as required in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil within site as directed by Project Manager.Soft/Hard Soil depth upto 1.5m

Earth work in excavation for pipe trenches of required width including excavation for sockets, dressing of sides, ramming of bottoms, including shoring, dewatering, disposal of the excavated material, refilling the soil as required in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil within site as directed by Project Manager.Extra for depth above 1.5 mtr but not exceeding 3mtrs.

Providing, laying, testing & jointing stoneware pipes grade `A’ with stiff mixture of cement mortar in the proportion of 1:1 (1 cement :1 fine sand) including laying cement conc. 1:5:10 (1 cement :5 fine sand :10 graded stone aggregate 40 mm nominal size) alround S.W. pipes & bed conc. as per standard design.100 mm dia

Providing, laying, testing & jointing stoneware pipes grade `A’ with stiff mixture of cement mortar in the proportion of 1:1 (1 cement :1 fine sand) including laying cement conc. 1:5:10 (1 cement :5 fine sand :10 graded stone aggregate 40 mm nominal size) alround S.W. pipes & bed conc. as per standard design.150 mm dia

Providing, laying, testing & jointing stoneware pipes grade `A’ with stiff mixture of cement mortar in the proportion of 1:1 (1 cement :1 fine sand) including laying cement conc. 1:5:10 (1 cement :5 fine sand :10 graded stone aggregate 40 mm nominal size) alround S.W. pipes & bed conc. as per standard design.200 mm dia

Providing and laying cement concrete 1:5:10 (1 cement :5 coarse cement :10 graded stone aggregate 40mm nominal size) alround SW pipes including bed concrete as per standard design.100 mm dia

Providing and laying cement concrete 1:5:10 (1 cement :5 coarse cement :10 graded stone aggregate 40mm nominal size) alround SW pipes including bed concrete as per standard design.150 mm dia

Providing and laying cement concrete 1:5:10 (1 cement :5 coarse cement :10 graded stone aggregate 40mm nominal size) alround SW pipes including bed concrete as per standard design.200 mm dia

Earth work in excavation for pipe trenches of required width including excavation for sockets, dressing of sides, ramming of bottoms, including shoring, dewatering, disposal of the excavated material, refilling the soil as required in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil within site as directed by Project Manager. Soft/Hard Soil depth upto 1.5m

Earth work in excavation for pipe trenches of required width including excavation for sockets, dressing of sides, ramming of bottoms, including shoring, dewatering, disposal of the excavated material, refilling the soil as required in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil within site as directed by Project Manager. Extra for depth above 1.5 mtr but not exceeding 3mtrs.

Providing, laying and jointing non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement :2 fine sand) including testing of joints etc. complete.150 mm dia

Providing, laying and jointing non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement :2 fine sand) including testing of joints etc. complete.200 mm dia

Providing, laying and jointing non-pressure NP3 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement :2 fine sand) including testing of joints etc. complete.150 mm dia

Providing, laying and jointing non-pressure NP3 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement :2 fine sand) including testing of joints etc. complete.200 mm dia

Providing and laying cement concrete 1:3:6 (1 cement :3 coarse cement :6 graded stone aggregate 40mm nominal size) upto haunches for pipes including bed concrete 15 cms thick as per standard design. 150 mm dia

Providing and laying cement concrete 1:3:6 (1 cement :3 coarse cement :6 graded stone aggregate 40mm nominal size) upto haunches for pipes including bed concrete 15 cms thick as per standard design. 200 mm dia

Earth work in excavation in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth; consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5m.

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5m, but not exceeding 3m (Rate is over coresponding basic item for depth upto 1.5 metre).

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 3m, but not exceeding 4.5m (Rate is over coresponding basic item for depth upto 1.5 metre).

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level. 1:4:8 (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size).

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level. 1:1:2 (1 cement :1 coarse sand :2 graded stone aggregate 20mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for:Foundations, footings, bases of columns etc. for mass concrete.

Extra for shuttering in circular work (20% of respective centring and shuttering items).

Reinforcement of R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Mild steel and medium tensile steel bars.

Brick work with bricks of class designation 75 in foundation and plinth in: Cement mortar 1:6 (1 cement :6 fine sand).

Providing and fixing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12 mm dia. steel bar conforming to IS: 1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specification mark to be visible even after fixing, including fixing in manholes with 30 x 20 x 15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Supplying and fixing C.I. Cover with frame for manholes:560mm diameter C.I. Cover & frame (heavy duty) the weight of the cover to be not less than 108 Kg.

Supplying and filling in plinth with coarsesand 1.5 to 2.0mm sand under floors including, watering, ramming consolidating and dressing complete.

Supplying and filling of stone boulders 15 - 20mm and down gauge.

300mm dia boring well - All kinds of soil.

300mm dia boring well - Oridinary Rock.

Providing and fixing 200mm nominal dia PVC ribbed screen Finolex pipe for recharged well with fittings complete conforming to DIN-4925.

Providing and laying gravels 5-10mm and down gauge.

Providing Geo Textile cloth below coarse sand layer.

Supplying, installing, testing and commissioning of centrifugal submersible sump pumps, suitable for 415 ± 10% Volts, 3 phase/230 ±10% volts 50 Hz A.C. power supply. Each pump shall be suitable for automatic/manual operation and shall be complete with control panel as per detailed specification. HEAT PUMP FOR HOT WATER SUPPLY. MAKE:- AO SMITH MODEL NO :- HPA-80C1.5A, Flow rate =4000 LTS PER DAYS . hot water tank , pump,

BOOSTER PUMP, Basement Drainage, (2 Nos. 1working+1stand By) Flow rate =50 LPS (each pump) Head = 30 Mtrs.

Sump Pit / BOOSTER PUMP, Basement Drainage, (2 Nos. 1working+1stand By) Flow rate =2 LPS (each pump) Head = 8 Mtrs. Solid Handling = 28 mm

Providing and fixing single sheet with metal structure and 12mm thick basion board, as per satisfaction of engineer incharge

Providing and fixing stone cladding façade work, as per satisfaction of engineer incharge

Providing and fixing CNC JALLI façade work, as per satisfaction of engineer incharge

Construction of UGT TANK, under ground water tank having capacity of 30000 lit cost includes tiling work also, as per satisfaction of engineer incharge

Construction of STP/ETP 50 KLD, as per satisfaction of engineer incharge

Providing and fixing , boom barriers, as per satisfaction of engineer incharge

Construction of Water bodies including civil works, as per satisfaction of engineer incharge

Supply, fixing, testing and Commissioning of bore well, 5"ODEX\DTH boring with Casing pipe(Jindal) 5" Casing Shoe 3 hp Submersible Pump set (Kirloskar) 3 hp Control Panel Board (Bch,Sadhna) 2.5 sqmm Submersible cable (Ashirwaad,BCH) 1.1/4" coloumn pipe (Ashirwaad) Tubewell Capset & Fitting Motor Installation, as per satisfaction of engineer incharge

HVAC WORKS Chillers: Lifting, shifting & Installation, of water cooled screw type chilled water machines on Terrace above 6th Floor. 220TR Capacity with star delta starter

Chillers: Lifting, shifting & Installation, of water cooled screw type chilled water machines on Terrace above 6th Floor. 110 TR Capacity with star delta starter

Condenser Pumps, Supply, erection, testing and commissioning of condenser water pump set capable of delivering 880 GPM of water against 24 mtr head each comprising of the following and complete as per specifications and as required.1 No. - Vertical Inline type pump with impellar, Shaft, epoxy Coated CI body and mechanical seal. 1 No. Suitable HP, TEFC squirrel cage induction motor with class 'F' insulation, 1450 RPM synch0nous speed, operating on 415 Volts ± 10 %, 3 phase, 50 Hz A.C. supply. Pump as above (3W+1S)

Chilled Water Primary Pumps, Supplying, erection, testing and commissioning of primary chilled/hot water pump set capable of delivering 528 GPM of water against a head 12 Mtr. each pump shall comprise the following as required as per specifications. 1 No. - Vertical Inline type pump with impellar, Shaft, epoxy Coated CI body and mechanical seal. 1 No.- Suitable HP, TEFC squirrel cage induction motor with class 'F' insulation,IP -55 P0tection, 1450 RPM synch0nous speed, operating on 415 volts ± 10%, 3 phase, 50 Hz A.C. supply. Pump as above (3W+1S)

Chilled/Hot Water Secondary Pumps (variable pumping system), Supplying, erection, testing and commissioning of package type vertical Inline type secondary chilled/hot water pumping system with VFD and all pump system cont0ller, comprising of:Pumping set withepoxy Coated cast I0n casing, impellers with shaft, connected to suitable capacity TEFC ventilated induction motor with class 'F' insulation, 3 Phase, 1450 RPM, suitable for 415 volts ± 10%, 3 phase, 50 Hz A.C. supply. Variable secondary Panel should have a dedicated p0grammable logic cont0ller with drive for each pump and with required no. of sensors and the entire unit has to be p0cured f0m the Pump manufacturer to ensure the smooth operation of the system. The P0grammable logic cont0ller shall be able to cont0l minimum 1 Pump and maximum of 4/6 Pumps, Automatic cascade cont0l of pumps, automatic sequence change, Friction loss compensation, pump status shall be there. Display shall be graphical type with backlight.Drive should have rated input frequency 50 Hz and output frequency range of 0.5 to 132 Hz. An IP54/IP55 Nema Standard powder coated steel enclosure for Basement/0of top, with sufficient capacity of cooling fan shall house all the electrical cont0l components. Mic0p0cessor based cont0l panel shall have suitable hardware & software so that it can be integrated directly to IBMS with standard communication open p0tocol using backnet / Modbus as well as open IP. (All the Pump set will have their cont0l panel with respect to the motor rating).All pumps to be p0vided with separate variable frequency drives. Cont0l panel should also consist of cooling fan. One panel for each job will be p0vided (for a set of two/three pumps) and the panels should be installed adjacent to each other.The pumps should be suitable for heating as well as chilled water circulation.Lot-Mounting frame work with anti vibration pads.Differential Pressure Transmitters as required.suitable flanged suction and delivery headers in C-Class MS.Complete set system to be mounted on a common MS base frame and shall follow following duty with following no. of pumps:Secondary chilled water pump sets, Flow Rate : 528 GPM Head : 35 Metre WC Pump as above (3W+1S)

Cooling Towers : Supply, installation, testing and commissioning of Induced draft FRP Cooling tower suitable for 300 TR , 9.1 lac Kcal/hr heat rejection capacity with PVC fillings with intergal louvers and drift eliminators open pan sutaible for water distribution complete with hot FRP water basin either fitted with spray nozzles or having self 0tating sprinklers, statically and dynamically balanced two nos. axial flow type fan-direct driven or driven th0ugh special bevelled reduction gear box with TEFC induction motor with IP-55 p0tection,Eff-1,suction screen, make up and quick fill arrangement, overflow and drain connections and suitable inspection ladder, access arrangement for cooling tower interior, anti vibration mountings etc complete as per specifications and as required.Water Leaving Temperature : 32.2 Deg C, Water Entering Temperature : 36.4 Deg C, Water Flow Rate : 1000 GPM, Ambient Wet Bulb Temperature : 28.3 Deg C, Cooling Tower as Above

Hot water pump (Monsoon Re-Heating) for OTsSupply,erection, testing and commissioning of monoblock chilled water centrifugal pump for Chilled water recirculation, pump set capable of delivering 50 GPM of water against 24 mtr head each comprising of the following and complete as required 1 No. - monoblock type pump with bronze impellar and mechanical seal. 1 No. Suitable HP, TEFC squirrel cage induction motor with class 'B' insulation, 3000 RPM synchronous speed, operating on 415 Volts ± 10 % , 3 phase , 50 Hz A.C. supply. Pump as above (1 working + 1stand by)

Hot Water Generators, Supply,installation, testing & Commissioning of electrically operated Hot Water Generator of 250 KW actual capacity made of 8mm M.S. sheet and dish end made of 10mm M.S. having 16 gauge stainless steel lining with heaters arranged in banks and Controller and Thermostat so that 190 GPM hot water is generated at 50°C with nominal variation, including 75mm thick resin bonded fibre glass insulation of 24 Kg / CUM density finished with 1.25mm thick aluminium sheet cladding including necessary Electrical panel with BMS compatible having suitable Incoming and outgoing Switchgears for Boiler, automatic Cont0ls including inlet and outlet connections for water complete with pressure release valve, low level cut-out, Autovent sight-glass as per specification complete as required. (Degree of protection IP52 with IS 2147) Hot Water Generator (HWG)(Winter Heating) Heating capacity : 250 KW, Water in temp. : 45 deg C, Water out temp : 50 deg C, HWG as Above

Hot Water Generator (HWG) (Monsoon Re-heat), Heating capacity : 50 KW, Water in temp. : 45 deg C, Water out temp : 50 deg C, HWG as Above

TREATED FRESH AIR UNITS, Supplying, installing, testing and commissioning of factory built Floor mounted double skin type air handling units made of 63 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.8 mm outside layer and 0.8 mm plane inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW forward curved centrifugal fan of 60 mm WC static pressure,8 Row deep cooling and 2 Row deep heating coil, section with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type Pre filters having efficiency 90% down to 10 mic0n, belt drive package with TEFC drive motor suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete with mixing box, drain connections with drain valve, stainless steel drain pan.3000 CFM: 40 MMSP, 8 Row deep

HRV Units S.I.T.C of Factory built Heat Reclaim Ventilation units of following capacities. 2000 CMH

Supplying, installing, testing and commissioning of factory built Ceiling Suspended double skin type air handling units made of 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.6 mm outside layer and plane GI of 0.6mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW forward curved centrifugal fan of required static pressure, 6/4 Row deep cooling/heating coil with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type pre filter , belt drive package with TEFC drive motor suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete, drain connections with stainless steel drain pan. 1600 CFM, 30 mmSP, 4 Row deep

Supplying, installing, testing and commissioning of factory built Ceiling Suspended double skin type air handling units made of 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.6 mm outside layer and plane GI of 0.6mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW forward curved centrifugal fan of required static pressure, 6/4 Row deep cooling/heating coil with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type pre filter , belt drive package with TEFC drive motor suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete, drain connections with stainless steel drain pan. 2000 CFM, 30 mmSP, 4 Row deep

Supplying, installing, testing and commissioning of factory built Ceiling Suspended double skin type air handling units made of 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.6 mm outside layer and plane GI of 0.6mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW forward curved centrifugal fan of required static pressure, 6/4 Row deep cooling/heating coil with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type pre filter , belt drive package with TEFC drive motor suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete, drain connections with stainless steel drain pan. 1600 CFM, 30 mmSP, 4 Row deep

Supplying, installing, testing and commissioning of factory built Ceiling Suspended double skin type air handling units made of 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.6 mm outside layer and plane GI of 0.6mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW forward curved centrifugal fan of required static pressure, 6/4 Row deep cooling/heating coil with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type pre filter , belt drive package with TEFC drive motor suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete, drain connections with stainless steel drain pan. 2500 CFM, 30 mmSP, 4 Row deep

Supplying, installing, testing and commissioning of factory built Ceiling Suspended double skin type air handling units made of 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.6 mm outside layer and plane GI of 0.6mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW forward curved centrifugal fan of required static pressure, 6/4 Row deep cooling/heating coil with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type pre filter , belt drive package with TEFC drive motor suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete, drain connections with stainless steel drain pan.3000 CFM, 30 mmSP, 4 Row deep

Supplying, installing, testing and commissioning of factory built Ceiling Suspended double skin type air handling units made of 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.6 mm outside layer and plane GI of 0.6mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW forward curved centrifugal fan of required static pressure, 6/4 Row deep cooling/heating coil with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type pre filter , belt drive package with TEFC drive motor suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete, drain connections with stainless steel drain pan. 3500 CFM, 30 mmSP, 4 Row deep

Supplying, installing, testing and commissioning of factory built Ceiling Suspended double skin type air handling units made of 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.6 mm outside layer and plane GI of 0.6mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW forward curved centrifugal fan of required static pressure, 6/4 Row deep cooling/heating coil with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type pre filter , belt drive package with TEFC drive motor suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete, drain connections with stainless steel drain pan.4000 CFM, 30 mmSP, 4 Row deep

Supplying, installing, testing and commissioning of factory built Ceiling Suspended double skin type air handling units made of 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.6 mm outside layer and plane GI of 0.6mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW forward curved centrifugal fan of required static pressure, 6/4 Row deep cooling/heating coil with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type pre filter , belt drive package with TEFC drive motor suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete, drain connections with stainless steel drain pan. 5000 CFM, 30 mmSP, 4 Row deep

Supplying, installing, testing and commissioning of factory built Ceiling Suspended double skin type air handling units made of 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.6 mm outside layer and plane GI of 0.6mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW forward curved centrifugal fan of required static pressure, 6/4 Row deep cooling/heating coil with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type pre filter , belt drive package with TEFC drive motor suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete, drain connections with stainless steel drain pan. 5500 CFM, 30 mmSP, 4 Row deep

Supplying, installing, testing and commissioning of factory built Ceiling Suspended double skin type air handling units made of 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.6 mm outside layer and plane GI of 0.6mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW forward curved centrifugal fan of required static pressure, 6/4 Row deep cooling/heating coil with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type pre filter , belt drive package with TEFC drive motor suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete, drain connections with stainless steel drain pan. 6000 CFM, 30 mmSP, 4 Row deep

Supplying, installing, testing and commissioning of factory built Ceiling Suspended double skin type air handling units made of 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.6 mm outside layer and plane GI of 0.6mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW forward curved centrifugal fan of required static pressure, 6/4 Row deep cooling/heating coil with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type pre filter , belt drive package with TEFC drive motor suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete, drain connections with stainless steel drain pan. 6500 CFM, 30 mmSP, 4 Row deep

AHU with Pre & Fine filters, Supplying, installing, testing and commissioning of factory built Ceiling Suspended double skin type air handling units made of 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.6 mm outside layer and plane GI of 0.6mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW backward curved centrifugal fan of 60 mm WC static pressure, 6 row deep cooling coil section with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type pre filter having efficiency 90% down to 10 micron and Fine filters having efficiency 99% down to 5 micron, belt drive package with TEFC drive motor suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete with stainless steel drain pan, complete as per specifications of following capacities:1600 CFM, 60 mmSP, 6 Row Deep

AHU with Pre & Fine filters, Supplying, installing, testing and commissioning of factory built Ceiling Suspended double skin type air handling units made of 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.6 mm outside layer and plane GI of 0.6mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW backward curved centrifugal fan of 60 mm WC static pressure, 6 row deep cooling coil section with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type pre filter having efficiency 90% down to 10 micron and Fine filters having efficiency 99% down to 5 micron, belt drive package with TEFC drive motor suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete with stainless steel drain pan, complete as per specifications of following capacities:3000 CFM, 60 mmSP, 6 Row Deep

AHU with Pre & Fine filters, Supplying, installing, testing and commissioning of factory built Ceiling Suspended double skin type air handling units made of 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.6 mm outside layer and plane GI of 0.6mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW backward curved centrifugal fan of 60 mm WC static pressure, 6 row deep cooling coil section with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type pre filter having efficiency 90% down to 10 micron and Fine filters having efficiency 99% down to 5 micron, belt drive package with TEFC drive motor suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, complete with stainless steel drain pan, complete as per specifications of following capacities:4000 CFM, 60 mmSP, 6 Row (CC) + 2 Row (HC) for minor OT

Floor mounted AHUs for Normal strelize Ots (@5 acph F.A . Supplying, installing, testing and commissioning of factory built Floor mounted double skin type air handling units with thermal break profile made of minimum 40 mm thick panels consisting of pre plasticized G.I casing made of thickness 0.6 mm outside layer and Aluminium sheet of thickness 0.8mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW backward curved centrifugal fan of 125 mm WC static pressure, 6 row deep cooling coil & 2 row deep heating coil section with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type pre filter having efficiency 90% down to 10 micron, Fine filters having efficiency 99% down to 5 micron , belt drive package with TEFC drive suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply,mixing box with suitable openings for fresh air and return air , stainless steel drain pan, necessary vibration isolation arrangement, etc, complete as per specifications of following capacities:The above AHU shall have provision of space for installation of steam type humidifier package & have remote controlled provision in the OTs for temp. & RH adjustment. (HEPA filters to be installed at terminals of laminar Flow Diffusers inside Ots) 6000 CFM, 125 mmSP, 6 row + 2 row deep

Floor mounted AHUs for Highly strelize Ots with HRW (@100% F.A) Supplying, installing, testing and commissioning of Double decker factory built Floor mounted double skin type air handling units with thermal break profile made of minimum 40 mm thick panels consisting of pre plasticized G.I casing made of thickness 0.6 mm outside layer and Aluminium sheet of thickness 0.8mm inside layer with polyurethene foam (PUF) insulation of density 32 kg/m3 factory injected between them by injection moulding machine, complete with blower section with blower DIDW backward curved centrifugal fan of 6000 CFM, 85 mm WC static pressure in supply stream and 5500 CFM, 40 mm WC static pressure in Exhaust stream with a heat recovery wheel , 8 row deep cooling coil & 2 row deep heating coil section with aluminium finned copper tubes (tube thickness not less than 0.5mm), filter sections with 50 mm thick washable synthetic type pre filter having efficiency 90% down to 10 micron, Fine filters having efficiency 99% down to 5 micron , belt drive package with TEFC drive suitable for 415 ± 10% volts, 50 Hz, 3 phase, A.C supply,mixing box , stainless steel drain pan, necessary vibration isolation arrangement, etc, complete as per specifications of following capacities:The above AHU shall have provision of space for installation of steam type humidifier package & have remote controlled provision in the OTs for temp. & RH adjustment. (HEPA filters to be installed at terminals of laminar Flow Diffusers inside Ots) 6000 CFM, 125 mmSP, 8 row + 2 row deep

PAN type Humidifier, Supply, install, test and commission wall / floor mounted Pan Type Humidifier package of following capacities.

Temperature and RH sensor and adjuster package. Supply,install,test and commission micro-processor based Room temperature , humidity sensor and remote adjuster package within a housing -wall ,suitable for mounting, .The package shall have a temperature and humidity display for operation rooms , and other critical areas. Sensor, adjuster (Snap acting humidistat/Proportional thermostat- Microprocessor based) and displayer package, as described above.

FAN COIL UNITS - Supply, installation, testing and commissioning of ceiling suspended High static type FCU's each complete with 3 Row deep cooling/heating coil of copper tubes aluminium fins construction, centrifugal fan, 3 speed motor, filters insulated drain fan, coil piping connections, condensate drain connection, as required as per specification & drawings with the following capacities:- 1.0 TR, 400CFM

FAN COIL UNITS - Supply, installation, testing and commissioning of ceiling suspended High static type FCU's each complete with 3 Row deep cooling/heating coil of copper tubes aluminium fins construction, centrifugal fan, 3 speed motor, filters insulated drain fan, coil piping connections, condensate drain connection, as required as per specification & drawings with the following capacities:- 1.5TR, 600CFM

FAN COIL UNITS - Supply, installation, testing and commissioning of ceiling suspended High static type FCU's each complete with 3 Row deep cooling/heating coil of copper tubes aluminium fins construction, centrifugal fan, 3 speed motor, filters insulated drain fan, coil piping connections, condensate drain connection, as required as per specification & drawings with the following capacities:- 2.0 TR,800CFM

FAN COIL UNITS - Supply, installation, testing and commissioning of ceiling suspended High static type FCU's each complete with 3 Row deep cooling/heating coil of copper tubes aluminium fins construction, centrifugal fan, 3 speed motor, filters insulated drain fan, coil piping connections, condensate drain connection, as required as per specification & drawings with the following capacities:- 2.5 TR, 1000CFM

FAN COIL UNITS - Supply, installation, testing and commissioning of ceiling suspended High static type FCU's each complete with 3 Row deep cooling/heating coil of copper tubes aluminium fins construction, centrifugal fan, 3 speed motor, filters insulated drain fan, coil piping connections, condensate drain connection, as required as per specification & drawings with the following capacities:- 3.0 TR, 1200CFM

HYDRONIC CASSETTE UNITS Supply, installation, testing and commissioning of ceiling suspended High static type casette's each complete with 3 row deep cooling/heating coil of copper tubes aluminium fins construction, centrifugal fan, 3 speed motor, filters insulated drain fan, coil piping connections, condensate drain connection, complete as required complete with bronze ball valve with and without strainer, PID valves, thermostats and electrical wiring, manual air vent valve etc. as required as per specification & drawings with the following capacities:-2.0 TR

Split Units : Supplying, fixing, testing and commissioning of 1.5 TR Hi Wall type split air-conditioning with inverter type cooling techonology, unit suitable to operate from 230±10% volt, 50 Hz, 1 phase power supply, with air-cooled evaporator with coil, fan, and fan motor, air-cooled condenser with hermetically sealed rotery / scroll compressor condenser coil, propeller fans controls, control panel, voltage stabilizer, Including control wiring, necessary power cable, M.S. frame duly painted to locate Outdoor Unit etc. The Refrigerant pipe size and gas quantity should suit to the copper pipe length at actual.

Supply, installation and testing of Refrigerant piping (total circuit including liquid & suction) with interconnecting cabling between indoor / outdoor units as per site incharge, 13 mm thick XLPE/EPDM insulation on pipes, gas charging, support complete in all respects for 1.5 TR HI Wall Split AC.

INSULATED CHILLED WATER PIPING: Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled/hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with close linked closed cell Nitrile Rubber with fire resistant (UL-723) having a low stable K-value of 0.027- 0.029 K.cal/hr.moC with min. density of 32 Kg/cum complete with type3, grade 1 0ofing feltstrip (as per IS: 1322 as amended upto date) at the joints repairing of damage to building etc. as per specifications and as required.The Pipes size 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, f0m minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia.. 250mm dia.(32mm insulation)

INSULATED CHILLED WATER PIPING: Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled/hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with close linked closed cell Nitrile Rubber with fire resistant (UL-723) having a low stable K-value of 0.027- 0.029 K.cal/hr.moC with min. density of 32 Kg/cum complete with type3, grade 1 0ofing feltstrip (as per IS: 1322 as amended upto date) at the joints repairing of damage to building etc. as per specifications and as required.The Pipes size 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, f0m minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia.. 200mm dia.(32mm insulation)

INSULATED CHILLED WATER PIPING: Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled/hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with close linked closed cell Nitrile Rubber with fire resistant (UL-723) having a low stable K-value of 0.027- 0.029 K.cal/hr.moC with min. density of 32 Kg/cum complete with type3, grade 1 0ofing feltstrip (as per IS: 1322 as amended upto date) at the joints repairing of damage to building etc. as per specifications and as required.The Pipes size 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, f0m minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia.. 150mm dia.(32mm insulation)150mm dia. (32mm insulation)

INSULATED CHILLED WATER PIPING: Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled/hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with close linked closed cell Nitrile Rubber with fire resistant (UL-723) having a low stable K-value of 0.027- 0.029 K.cal/hr.moC with min. density of 32 Kg/cum complete with type3, grade 1 0ofing feltstrip (as per IS: 1322 as amended upto date) at the joints repairing of damage to building etc. as per specifications and as required.The Pipes size 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, f0m minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia.. 125mm dia.(32mm insulation)

INSULATED CHILLED WATER PIPING: Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled/hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with close linked closed cell Nitrile Rubber with fire resistant (UL-723) having a low stable K-value of 0.027- 0.029 K.cal/hr.moC with min. density of 32 Kg/cum complete with type3, grade 1 0ofing feltstrip (as per IS: 1322 as amended upto date) at the joints repairing of damage to building etc. as per specifications and as required.The Pipes size 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, f0m minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia.. 100mm dia.(32mm insulation)

INSULATED CHILLED WATER PIPING: Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled/hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with close linked closed cell Nitrile Rubber with fire resistant (UL-723) having a low stable K-value of 0.027- 0.029 K.cal/hr.moC with min. density of 32 Kg/cum complete with type3, grade 1 0ofing feltstrip (as per IS: 1322 as amended upto date) at the joints repairing of damage to building etc. as per specifications and as required.The Pipes size 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, f0m minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia.. 80mm dia.(32mm insulation)

INSULATED CHILLED WATER PIPING: Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled/hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with close linked closed cell Nitrile Rubber with fire resistant (UL-723) having a low stable K-value of 0.027- 0.029 K.cal/hr.moC with min. density of 32 Kg/cum complete with type3, grade 1 0ofing feltstrip (as per IS: 1322 as amended upto date) at the joints repairing of damage to building etc. as per specifications and as required.The Pipes size 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, f0m minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia..65mm dia.(32mm insulation)

INSULATED CHILLED WATER PIPING: Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled/hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with close linked closed cell Nitrile Rubber with fire resistant (UL-723) having a low stable K-value of 0.027- 0.029 K.cal/hr.moC with min. density of 32 Kg/cum complete with type3, grade 1 0ofing feltstrip (as per IS: 1322 as amended upto date) at the joints repairing of damage to building etc. as per specifications and as required.The Pipes size 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, f0m minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia..50mm dia.(32mm insulation)

INSULATED CHILLED WATER PIPING: Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled/hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with close linked closed cell Nitrile Rubber with fire resistant (UL-723) having a low stable K-value of 0.027- 0.029 K.cal/hr.moC with min. density of 32 Kg/cum complete with type3, grade 1 0ofing feltstrip (as per IS: 1322 as amended upto date) at the joints repairing of damage to building etc. as per specifications and as required.The Pipes size 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, f0m minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia..40mm dia.(32mm insulation)

INSULATED CHILLED WATER PIPING: Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled/hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with close linked closed cell Nitrile Rubber with fire resistant (UL-723) having a low stable K-value of 0.027- 0.029 K.cal/hr.moC with min. density of 32 Kg/cum complete with type3, grade 1 0ofing feltstrip (as per IS: 1322 as amended upto date) at the joints repairing of damage to building etc. as per specifications and as required.The Pipes size 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, f0m minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia..32mm dia.(32mm insulation)

INSULATED CHILLED WATER PIPING: Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled/hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with close linked closed cell Nitrile Rubber with fire resistant (UL-723) having a low stable K-value of 0.027- 0.029 K.cal/hr.moC with min. density of 32 Kg/cum complete with type3, grade 1 0ofing feltstrip (as per IS: 1322 as amended upto date) at the joints repairing of damage to building etc. as per specifications and as required.The Pipes size 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, f0m minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia..25mm dia.(32mm insulation)

Aluminium Cladding :Supply & installation of 26 ga Aluminium Cladding on Exposed chilled water pipe & valves.

BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 300mm dia.

BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 200mm dia.

BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 150mm dia.

BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 125mm dia.

BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 100mm dia.

BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 50mm dia.

BALL VALVE : 40mm dia.

BALL VALVE : 32mm dia.

BALL VALVE : 25mm dia.

NON - RETURN VALVE 200mm dia.

NON - RETURN VALVE 125mm dia.

Y - STRAINER, 125mm dia.

Y - STRAINER, 50mm dia.

Y - STRAINER, 40mm dia.

Y - STRAINER, 32mm dia.

BALL VALVE SET WITH & WITHOUT STRAINER 25 mm dia

Providing, fixing, testing & commissioning of 2-way modulating valve with snap acting thermostat, including wiring etc. complete as per specification and drawing. 25 mm dia

PRESSURE INDEPENDENT BALANCING CUM CONTOL VALVE WITH THERMOSTAT Pressure Independent Balancing cum Cont0l Valve (PIBCV) which shall be 2 way combined valve of PN 10 rating for flow limitation, cont0lling flow & cont0lling Delta P. Valve body upto 32mm shall be brass and cast i0n above 32mm.Valve should be equipped with elect0nic modulating actuator for AHU which can accept either "4(0)-20 mA / 2(0)-10 V DC signals. Operating voltage for actuator shall be 24 V AC. The actuator should be connected to p0portionate thermostat. Delta p cont0ller should ensure 100% cont0l valve authority always at all load conditions (part load and full load).Stepless balancing adjustments shall be in valve and cont0l adjustments in actuator. The differential pressure function shall be a diaphragm and shall be out of the main flow to avoid valve blockages and other services issue. Valve along with actuator and cold thermostat shall offer logarithmic cont0l characteristics complete as per specification. The flow rates of chilled water are as below :64.6 - 102 LPM- 40 mm

PRESSURE INDEPENDENT BALANCING CUM CONTOL VALVE WITH THERMOSTAT Pressure Independent Balancing cum Cont0l Valve (PIBCV) which shall be 2 way combined valve of PN 10 rating for flow limitation, cont0lling flow & cont0lling Delta P. Valve body upto 32mm shall be brass and cast i0n above 32mm.Valve should be equipped with elect0nic modulating actuator for AHU which can accept either "4(0)-20 mA / 2(0)-10 V DC signals. Operating voltage for actuator shall be 24 V AC. The actuator should be connected to p0portionate thermostat. Delta p cont0ller should ensure 100% cont0l valve authority always at all load conditions (part load and full load).Stepless balancing adjustments shall be in valve and cont0l adjustments in actuator. The differential pressure function shall be a diaphragm and shall be out of the main flow to avoid valve blockages and other services issue. Valve along with actuator and cold thermostat shall offer logarithmic cont0l characteristics complete as per specification. The flow rates of chilled water are as below :102.4 - 189 LPM - 50 mm

FLOW SWITCH

Auto Air - purge valve of 15mm dia (Air Vent will be fitted with an isolating ball valve )

Manual Air - purge valve of 15mm dia

THERMOMETER

PRESSURE GAUGE

EXPANSION TANK : Supply, installation, testing of CLOSE type expansion tank of MS Construction. Outlets for system connection over flow and drain 40 mm dia. Make up connection with float valve drain valve and incoming line valves, vent connections, valves and fittings as required.1000 Litre

AIR SEPARATOR : Supply,installation,testing and commissioning of Centrifugal type air seperator complete with flanged connection and as per the specifications and duly insulated with 32 mm thick nitrile rubber and cladded with 26G aluminum sheet. 300 mm Dia Air Separator , duly insulated.

Supply, installation, testing and commisisoning of insulated GI Medium condensate drain water piping with bends reducers tees, supports etc. The insulation shall be with pipe sections of nitrile rubber of 9mm thick as per specifications and drawings.50mm dia.

Supply, installation, testing and commisisoning of insulated GI Medium condensate drain water piping with bends reducers tees, supports etc. The insulation shall be with pipe sections of nitrile rubber of 9mm thick as per specifications and drawings.40mm dia.

Supply, installation, testing and commisisoning of insulated GI Medium condensate drain water piping with bends reducers tees, supports etc. The insulation shall be with pipe sections of nitrile rubber of 9mm thick as per specifications and drawings.32mm dia.

Supply, installation, testing and commisisoning of insulated GI Medium condensate drain water piping with bends reducers tees, supports etc. The insulation shall be with pipe sections of nitrile rubber of 9mm thick as per specifications and drawings.25mm dia.

CONDENSER WATER PIPE: Supplying, fixing, testing and commissioning of condenser water pipes of following sizes and materials along with necessary clamps, vibration-isolators and fittings such as bends, tees etc but excluding strainer and gauges etc adequately supported on rigid supports/ including painting media vavels including minor holes & works making of good the damage dove welded black steel pipe as IS:3589 walls etc as per specifications and required.F0m minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia & f0m minimum 7mm thick M.S. sheet for pipes of 400 mm dia & above.300mm dia.

CONDENSER WATER PIPE: Supplying, fixing, testing and commissioning of condenser water pipes of following sizes and materials along with necessary clamps, vibration-isolators and fittings such as bends, tees etc but excluding strainer and gauges etc adequately supported on rigid supports/ including painting media vavels including minor holes & works making of good the damage dove welded black steel pipe as IS:3589 walls etc as per specifications and required.F0m minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia & f0m minimum 7mm thick M.S. sheet for pipes of 400 mm dia & above.300mm dia.

CONDENSER WATER PIPE: Supplying, fixing, testing and commissioning of condenser water pipes of following sizes and materials along with necessary clamps, vibration-isolators and fittings such as bends, tees etc but excluding strainer and gauges etc adequately supported on rigid supports/ including painting media vavels including minor holes & works making of good the damage dove welded black steel pipe as IS:3589 walls etc as per specifications and required.F0m minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia & f0m minimum 7mm thick M.S. sheet for pipes of 400 mm dia & above.200mm dia.

CONDENSER WATER PIPE: Supplying, fixing, testing and commissioning of condenser water pipes of following sizes and materials along with necessary clamps, vibration-isolators and fittings such as bends, tees etc but excluding strainer and gauges etc adequately supported on rigid supports/ including painting media vavels including minor holes & works making of good the damage dove welded black steel pipe as IS:3589 walls etc as per specifications and required.F0m minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia & f0m minimum 7mm thick M.S. sheet for pipes of 400 mm dia & above.150mm dia.

CONDENSER WATER PIPE: Supplying, fixing, testing and commissioning of condenser water pipes of following sizes and materials along with necessary clamps, vibration-isolators and fittings such as bends, tees etc but excluding strainer and gauges etc adequately supported on rigid supports/ including painting media vavels including minor holes & works making of good the damage dove welded black steel pipe as IS:3589 walls etc as per specifications and required.F0m minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia & f0m minimum 7mm thick M.S. sheet for pipes of 400 mm dia & above.100mm dia.

BUTTERFLY VALVE WITH ON/OFF TYPE MOTORIZED ACTUATOR 200mm dia.

BALANCING VALVE with built in measuring facility with C I body flanged construction with EPDM Coated disc with long pitch with potded out pipe insulation & PN 10 pressure rating as specified. 200mm dia.

BALANCING VALVE with built in measuring facility with C I body flanged construction with EPDM Coated disc with long pitch with potded out pipe insulation & PN 10 pressure rating as specified. 150mm dia.

BALANCING VALVE with built in measuring facility with C I body flanged construction with EPDM Coated disc with long pitch with potded out pipe insulation & PN 10 pressure rating as specified. 125mm dia.

BALANCING VALVE with built in measuring facility with C I body flanged construction with EPDM Coated disc with long pitch with potded out pipe insulation & PN 10 pressure rating as specified. 50mm dia.

BALANCING VALVE with built in measuring facility with C I body flanged construction with EPDM Coated disc with long pitch with potded out pipe insulation & PN 10 pressure rating as specified. 40mm dia.

BALANCING VALVE with built in measuring facility with C I body flanged construction with EPDM Coated disc with long pitch with potded out pipe insulation & PN 10 pressure rating as specified. 32mm dia.

Pot strainer having MS body, bolted cover, flanged ends, basket of stainless steel screen with 1.5 mm perforations and a permanent magnet for condenser water application complete with flanges, nuts-bolts, gaskets etc. as per specifications. 300 mm dia.

Supply, fabrication, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per app0ved drawings of following gauges as per SMACNA standard:-Thickness 26 G sheet

Supply, fabrication, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per app0ved drawings of following gauges as per SMACNA standard:-Thickness 24 G sheet

Supply, fabrication, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per app0ved drawings of following gauges as per SMACNA standard:-Thickness 22 G sheet

Supply, fabrication, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per app0ved drawings of following gauges as per SMACNA standard:-Thickness 20 G sheet

Supply, fabrication, installation, balancing and commissioning of Site fabricated GSS sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per app0ved drawings of following gauges :- ONLY FOR PIECES WHICH COULD NOT HAVE BEEN FACTORY FABRICATED.Thickness 26 G sheet

Supply, fabrication, installation, balancing and commissioning of Site fabricated GSS sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per app0ved drawings of following gauges :- ONLY FOR PIECES WHICH COULD NOT HAVE BEEN FACTORY FABRICATED.Thickness 24 G sheet

Supply, fabrication, installation, balancing and commissioning of Site fabricated GSS sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per app0ved drawings of following gauges :- ONLY FOR PIECES WHICH COULD NOT HAVE BEEN FACTORY FABRICATED.Thickness 22 G sheet

Supply, fabrication, installation, balancing and commissioning of Site fabricated GSS sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per app0ved drawings of following gauges :- ONLY FOR PIECES WHICH COULD NOT HAVE BEEN FACTORY FABRICATED.Thickness 20 G sheet

Supply, installation, balancing and commissioning of Factory fabricated Aluminium sheet metal (conforming to IS:737-1955) rectangular ducting as per BIS (IS : 655 ) standard, silicon sealed complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following gauges:- (FOR ALL OT, AHU AND MRI)Thickness 24 G sheet

Supply, installation, balancing and commissioning of Factory fabricated Aluminium sheet metal (conforming to IS:737-1955) rectangular ducting as per BIS (IS : 655 ) standard, silicon sealed complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following gauges:- (FOR ALL OT, AHU AND MRI)Thickness 22 G sheet

Supply, installation, balancing and commissioning of Factory fabricated Aluminium sheet metal (conforming to IS:737-1955) rectangular ducting as per BIS (IS : 655 ) standard, silicon sealed complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following gauges:- (FOR ALL OT, AHU AND MRI)Thickness 20 G sheet

Supplying and fixing of laminated aluminium foil of mat finish closed cell Nitrile rubber (class "O") insulation on existing duct after applying two coats of cold sitting adhesive (CPRX compound). The joints shall sealed with 50mm. wide and 3mm.thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.Supply and installation of 13mm thick, nitrile rubber insulation for supply air duct, complete with mechanical and duct supports as per specifications.

Supplying and fixing of laminated aluminium foil of mat finish closed cell Nitrile rubber (class "O") insulation on existing duct after applying two coats of cold sitting adhesive (CPRX compound). The joints shall sealed with 50mm. wide and 3mm.thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. Supply and installation of 9 mm thick, nitrile rubber insulation for Return air duct, complete with mechanical and duct supports as per specifications..

Supplying and fixing of open cell Nitrile rubber (class "O") insulation on existing duct after applying two coats of cold sitting adhesive (CPRX compound).Supplying, installing & testing of acoustic lining within supply and return air ducts with 10mm thick open cell nitrile rubber insulation material as per the specifications. All ducts shown cross hatched on the approved shop drawings shall be provided with acoustic lining as per the specifications.

Supply, installation, testing & Commissioning of opposed blade 20 Gauge G.I volume control dampers (manual cont0l) within ducts to be p0vided with suitable links, louvers, and quadrants for manual cont0l of volume of air flow and for p0per balancing of the air distribution system.

Supplying, installation, testing and commissioning of fire dampers, the blades and frame shall be min. 1.6 mm thick GI and factory fitted in a sleeve made out of 1.6 mm thick GI of min. 400 mm long, as & where required, of required sizes including control wiring. The damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal. CBRI tested and certified for 90 minute fire rating etcFire damper. complete as required and as per specifications. (Total assembly should be UL listed)

Motorized Actuator with control and temperature sensor complete with all respects.

Supply, installation, testing and commissioning of anodised aluminium fresh air louvers with bird screen and volume control damper with lever mounting arrangement etc. as per specifications and drawings.

Supply, installation, testing and commissioning of anodised aluminium exhaust air louvers with bird screen, as per specifications and drawings.

Supply, installation, testing and commissioning of anodised/power coating aluminium fresh air louvers with bird screen and volume cont0l damper with lever mounting arrangement etc. as per specifications and drawings.

Supply, fixing and commissioning of powder coated extruded aluminum grilles / diffuser complete with nuts, bolts, screws etc. as per app0ved drawings and specfications.Supply air grilles with volume control damper

Supply, fixing and commissioning of powder coated extruded aluminum grilles / diffuser complete with nuts, bolts, screws etc. as per app0ved drawings and specfications.Return air grilles without volume control damper

Supply, fixing and commissioning of powder coated extruded aluminum grilles / diffuser complete with nuts, bolts, screws etc. as per app0ved drawings and specfications.Supply air diffuser with volume control damper

Supply, fixing and commissioning of powder coated extruded aluminum grilles / diffuser complete with nuts, bolts, screws etc. as per app0ved drawings and specfications.Return air diffuser without volume control damper

Supply, fixing and commissioning of powder coated extruded aluminum Linear Slot type Grilles with dampers 150 mm wide complete with nuts, bolts, screws etc. as per approved drawings and specifications.

Supply, laying testing and commissioning of following sizes of XLPE insulated PVC sheathed armoured aluminium conductor cable of 1.1 KV grade on existing cable tray / surface including clamps, ties etc. as required. 4 Core 6 Sqmm.

Supply, laying testing and commissioning of following sizes of XLPE insulated PVC sheathed armoured aluminium conductor cable of 1.1 KV grade on existing cable tray / surface including clamps, ties etc. as required. 3.5 Core 300 Sqmm.

Supply, laying testing and commissioning of following sizes of XLPE insulated PVC sheathed armoured aluminium conductor cable of 1.1 KV grade on existing cable tray / surface including clamps, ties etc. as required. 3 Core 35Sqmm.

Supply, laying testing and commissioning of following sizes of XLPE insulated PVC sheathed armoured aluminium conductor cable of 1.1 KV grade on existing cable tray / surface including clamps, ties etc. as required. 4 Core 16 Sqmm.

Supplying and making end termination with brass compression glands and Al. lugs for following size of PVC insulated and PVC sheathed / XLPE Al. conductor cable of 1.1 KV grade as required. 2 Core 6 Sqmm.

Supplying and making end termination with brass compression glands and Al. lugs for following size of PVC insulated and PVC sheathed / XLPE Al. conductor cable of 1.1 KV grade as required. 3 Core 6 Sqmm.

Supplying and making end termination with brass compression glands and Al. lugs for following size of PVC insulated and PVC sheathed / XLPE Al. conductor cable of 1.1 KV grade as required. 3 Core 10 Sqmm.

Supplying and making end termination with brass compression glands and Al. lugs for following size of PVC insulated and PVC sheathed / XLPE Al. conductor cable of 1.1 KV grade as required. 4 Core 10 Sqmm.

Supplying and making end termination with brass compression glands and Al. lugs for following size of PVC insulated and PVC sheathed / XLPE Al. conductor cable of 1.1 KV grade as required. 4 Core 6 Sqmm.

Supplying and making end termination with brass compression glands and Al. lugs for following size of PVC insulated and PVC sheathed / XLPE Al. conductor cable of 1.1 KV grade as required. 3.5 Core 35 Sqmm.

Supplying and making end termination with brass compression glands and Al. lugs for following size of PVC insulated and PVC sheathed / XLPE Al. conductor cable of 1.1 KV grade as required. 3.5 Core 70 Sqmm.

Supplying and making end termination with brass compression glands and Al. lugs for following size of PVC insulated and PVC sheathed / XLPE Al. conductor cable of 1.1 KV grade as required. 3.5 Core 120 Sqmm.

Supplying and making end termination with brass compression glands and Al. lugs for following size of PVC insulated and PVC sheathed / XLPE Al. conductor cable of 1.1 KV grade as required. 3.5 Core 300 Sqmm.

Supplying and making end termination with brass compression glands and Al. lugs for following size of PVC insulated and PVC sheathed / XLPE Al. conductor cable of 1.1 KV grade as required. 3 Core 35 Sqmm.

Supplying and making end termination with brass compression glands and Al. lugs for following size of PVC insulated and PVC sheathed / XLPE Al. conductor cable of 1.1 KV grade as required. 3 Core 16 Sqmm.

Supplying and making end termination with brass compression glands and Al. lugs for following size of PVC insulated and PVC sheathed / XLPE Al. conductor cable of 1.1 KV grade as required. 4 Core 16 Sqmm.

P0viding & fixing of control wiring/power cabling with following sizes of copper conductor armoured cable between indoor and outdoor units directly on surface of wall/ existing channel i/c making connection etc. as reqd.6 x 1.5 sq.mm

Supply & Fixing of following Sizes of G.I. perforated type cables trays including suspending f0m ceiling with MS angle, 0ds connection pieces, G.I. nut bolts, G.I. washers, fasteners etc. as required.150 mm. Width x 50mm. Depth x 1.6mm. Thickness.

Supply & Fixing of following Sizes of G.I. perforated type cables trays including suspending f0m ceiling with MS angle, 0ds connection pieces, G.I. nut bolts, G.I. washers, fasteners etc. as required.300 mm. Width x 50mm. Depth x 1.6mm. Thickness.

Supply & Fixing of following Sizes of G.I. perforated type cables trays including suspending f0m ceiling with MS angle, 0ds connection pieces, G.I. nut bolts, G.I. washers, fasteners etc. as required.900 mm. Width x 75mm. Depth x 2.0mm. Thickness.

FIRE FIGHTING WORKS Supply installation, testing and commissioning) of electrically driven fire pump, suitable for automatic operation consisting of the following:

Supply, installation, testing and commissioning of jockey pump comprising of the following:

Supply, installation, testing and commissioning of Diesel Engine driven fire pump suitable for automatic operation comprising of the following..) AMF Panel for Diesel Pump.

Control Panel for fire fighting equipments in Plant Room :-Control Panel as described above.

Providing and fixing Chrome finish quartzoid bulb sprinklers(UL/FM listed/approved) of size 15mm dia to be Operated at 68 Deg C. Including two piece of adjustable C.P. Rosset complete as required.b) Side Wall Type

Providing, laying, jointing and testing of following sizes of CLASS C HEAVY DUTY MS pipes conforming to IS-3589/1239.200 mm dia

Providing, laying, jointing and testing of following sizes of CLASS C HEAVY DUTY MS pipes conforming to IS-3589/1239.150 mm dia

Providing, laying, jointing and testing of following sizes of CLASS C HEAVY DUTY MS pipes conforming to IS-3589/1239.100 mm dia

Providing, laying, jointing and testing of following sizes of CLASS C HEAVY DUTY MS pipes conforming to IS-3589/1239.80 mm dia

Providing, laying, jointing and testing of following sizes of CLASS C HEAVY DUTY MS pipes conforming to IS-3589/1239.65 mm dia

Providing, laying, jointing and testing of following sizes of CLASS C HEAVY DUTY MS pipes conforming to IS-3589/1239.50 mm dia

Providing, laying, jointing and testing of following sizes of CLASS C HEAVY DUTY MS pipes conforming to IS-3589/1239.40 mm dia

Providing, laying, jointing and testing of following sizes of CLASS C HEAVY DUTY MS pipes conforming to IS-3589/1239.32 mm dia

Providing, laying, jointing and testing of following sizes of CLASS C HEAVY DUTY MS pipes conforming to IS-3589/1239.25 mm dia

Supplying and fixing single headed internal hydrant valve.

Supplying and fixing single headed external yard hydrant valve.

Supply, installation, testing & commissioning of Butterfly Valve PN 1.6.a) 200 mm dia

Supply, installation, testing & commissioning of Butterfly Valve PN 1.6.a) 150 mm dia

Supply, installation, testing & commissioning of Butterfly Valve PN 1.6.a) 80 mm dia

Supplying and fixing orifice plate.

Providing, installation, testing & commissioning of dual plate Non-Return valve.a) 200 mm dia

Providing, installation, testing & commissioning of dual plate Non-Return valve.a) 100 mm dia

Providing, installation, testing and commissioning stainless steel strainera) 100 mm dia.

Providing, installation, testing and commissioning of gun metal valves of following sizes as required.a) 50 mm dia

Providing, installation, testing and commissioning of gun metal valves of following sizes as required.a) 25 mm dia

Supplying and fixing 63mm dia, 15 mtr long RRL hose pipe.

Supplying and fixing first -Aid hose reel.

Supplying and fixing hose cabinet of size 900mmx600mmx500mm made of 2 mm thick MS sheet with 6 mm thick glazed glass doors.

Supplying and fixing 63mm branch pipe.

Supplying and fixing 4 way fire brigade connection of cast iron body.

Supplying and fixing 2 way FBC of CI body.

Supplying and fixing air vessel made of 250 mm dia.

Providing fixing testing and commissioning of 15 mm size quartzoid bulb type sprinklers.

Providing, jointing and testing of sprinklers through flexible connections.

Providing and fixing Pressure switch in the MS pipe Line including connection etc. as required.

Providing and fixing flow switches in 100/150mm dia MS pipe.

Providing and fixing pressure transducer in MS pipe line (pressure range 0-10 kg/cm) suitable for 12 volts /24 DC. Including connection etc. as required.

Providing and fixing angle iron (40mmx40mm x5mm) door frame and MS sheet (2mm thick) cum glass shutter of size 2.1 mtr. X l.2mtr.

Providing and fixing of carbon-di-oxide type fire extinguishers.a) Capacity 4.5 Kg.

Providing and fixing of ABC Powder type fire extinguishers.a) Capacity 5 Kg.

FURNITURE WORKS Baldeo Furniture Double Bed opening Form Top 1830 x 1830 x125 Baldeo Furniture for ground floor as per satisfaction of engineer incharge.

Durian wooden DOUBLE BED without storage box 1830x1830x40 FOR FIRST FLOOR as per satisfaction of engineer incharge.

Harlison wooden DOUBLE BED storage box 1905x1525x100 FOR SECOND FLOOR as per satisfaction of engineer incharge.

Panam work smart metal beds (without mattress) with frame of MS Pipe SINGLE BED FOR SEVENT/DRIVER OUTHOUSE as per satisfaction of engineer incharge.

Durian spring MATRESS dimensions 1905 X1829mm FOR GROUND FLOOR as per satisfaction of engineer incharge.

Purerest spring Matress dimensions 1829 X1829mm FOR FIRST FLOOR,as per satisfaction of engineer incharge.

Repose spring mattress dimensions 1905 X1829mm for second floor, as per satisfaction of engineer incharge.

Cocofoam spring mattress dimensions 1981 X914mm for servant/driver outhouse, as per satisfaction of engineer incharge.

Harlison commercial board bed side table (BST -2(4369694) for ground floor, as per satisfaction of engineer incharge.

Graphic commercial board bed side table (BST-1034) FOR FIRST FLOOR, as per satisfaction of engineer incharge.

NGFC-New Golden Furnishers Co plywood bed side table (NGFC-S714E) FOR SECOND FLOOR, as per satisfaction of engineer incharge.

Bed side Lamp for ground floor as per satisfaction of engineer incharge.

Bed side Lamp FOR FIRST FLOOR as per satisfaction of engineer incharge.

Bed side Lamp FOR SECOND FLOOR as per satisfaction of engineer incharge.

Unbranded other cuptype hanging light (Long Lamp Floor Light) floor lamp for ground floor, as per satisfaction of engineer incharge.

Beverly Studio Iron and fiver pedestral lamp, 100 watt beverly studio floor lamp for first floor ,as per satisfaction of engineer incharge.

floor lamp for second floor, as per satisfaction of engineer incharge.

GS MART MEDI - GS mart exports centre table with marble top of 762mm (Dia) cofee table for ground floor, as per satisfaction of engineer incharge.

Furncasa round centre table with marble top of 914mm X 609mm cofee table for first floor, as per satisfaction of engineer incharge.

Furnestry round centre table with marble top of 914mm X 914mm cofee table for second floor, as per satisfaction of engineer incharge.

Shreevkg 1 seater sofa with fabric cover (1006) lounge chair for ground floor, as per satisfaction of engineer incharge.

Vassio 1 seater sofa with fabric cover lounge chairfor first floor, as per satisfaction of engineer incharge.

Vassio 1 seater sofa with fabric cover lounge chairfor second floor, as per satisfaction of engineer incharge.

Devent collection 1675X760mm Executive computer table devent collection (DK-111) study tablefor ground floor, as per satisfaction of engineer incharge.

DNR Systems 915 X610MM Executive computer table for first floor, as per satisfaction of engineer incharge.

Shree Hariom alumunium 915 x460mm Executive computer table shree hariom alumunium (NE-EX.C.T-3032) for second floor, as per satisfaction of engineer incharge.

Harlison restaurant/ cafeteria Chair with frame of other wood and wood seat (RC-6(3782444) /study chair for ground floor ,as per satisfaction of engineer incharge.

DNR Restaurant / cafeteria chair with frame of MS power coated and ply seat / study chair for first floor,as per satisfaction of engineer incharge.

DNR Restaurant / cafeteria chair with frame of MS power coated and ply seat / study chair for second floor, as per satisfaction of engineer incharge.

Sony type / category / class of TV set smart TV (2) actual screen size sony LED TV 32" (KD -32W830K) as per satisfaction of engineer incharge.

Sony type / category / class of TV set smart TV (2) actual screen size sony LED TV 50" (KD-50X75L) as per satisfaction of engineer incharge.

Total system, Tata sky per room required as per satisfaction of engineer incharge.

Unbranded TV & Entertainment units, Number of panels 2 NA LCD TV panel unit as per satisfaction of engineer incharge.

Urbangrey Bar counter Front bar and under bar mini baar (BAR COUNTER) as per satisfaction of engineer incharge.

Bajaj 1.5 L 1.5 KW Stainless steel Electric kettle as per satsfaction of as per satsfaction of engineer incharge.

Turkeen ABS plastics hair dryer number of speed in hair dryer 2 Turkeen (THR003) as per satisfaction of engineer incharge.

HIMACHAL WOODCRAFTS 900X450X750mm (with one shelf) Modular side storage unit Himachal woodcrafts (Modular side storage 001) aas per satisfaction of engineer incharge.

Madhubhani-painting GeM madhubani painting of actual length (in cm) 55 and actual width (in cm) 55 with framing madhubhani- Wall Paintings as per satisfaction of engineer incharge.

Devent collection wooden almirah, height 2250 wardrobe as per satisfaction of engineer incharge.

Godrej security solutions deposite safe ( non tool resistant) An individually secured container for paper / cash / documents (Godrej home locker 25 Ltr Digitalivory) Electrornic safe as per satisfaction of engineer incharge.

KAIRO-KAIRO Furniture interior polyster plain door curtain ( blackout double layer beige color & black lining) as per satisfaction of engineer incharge.

ZED Hanging system rectangular mirror (ZED-BTM-007) as per satisfaction of engineer incharge.

Abhishek enterprises - square matt tress name plate 16 inch 12 inch (tress name plate 12X16") Room no. Plateas per satisfaction of engineer incharge.

TECH24 Access controlled handle door lock only RFID card based access control (HL200) intelligent door lock as per satisfaction of engineer incharge.

Unbranded toughened (tempered safety glass of 12 mm. thickness,( Safety Glasses with Clear Lenses) Length (ft) 0.1-1.0, Breadth (ft) 0.1-1.0 as per satisfaction of engineer incharge.

vanity including hand towel as per satsfaction of site engineer.

Priti teak wood 6 seater restaurant dinning Table 6x3 ft. (Teak Wood 6 Seater Restaurant Table) rectangular, Product id: 5116877-68985431559, Material of top finish-Teak laminate/ply with polish, Length of table ±10mm (Diameter in case of Round) 1800 mm, Depth of table ±10mm 900 mm Thickness of top in mm (+/- 5%) 25 mm as per satisfaction of engineer incharge.

SSF SS-202 4 seater restaurant dinning Table 3x3 (CAFETERIA TABLE) ft. Product id: 5116877-68101493129, Shape of Table Square, Seating Capacity-4, Material of top-Teak Wood, Material of understructure, SS-202, Material of top finish, Melamine Polish Length of table ±10mm (Diameter in case of Round), 900 mm Depth of table ±10mm, 900 mm, Thickness of top in mm (+/- 5%) 25 mm, as per satisfaction of engineer incharge.r.

VAIBHAVI Restaurant / Cafeteria Chair with frame of Other wood and wood seat, (V-RC-030), Product id: 5116877-47626858600, Chair Armrest Without, Type of seat-wood, Seat Cushion With Back Rest Cushion, Without Upholstery, Polyester fabric, Material of frame Other wood, Chair height (overall) ±10mm, 1050mm, Backrest width ±10mm, 450 as per satisfaction of engineer incharge..

Angular 3 Seater Sofa With Leather Fabric Cover (ANG_SV_438) Product id: 5116877-27781596386 Total Number of Seats in the Sofa Set-3, Number of Single Seater Units (Nos), No Single Seater Unit, Number of Two Seater Units (Nos) No Two Seater Unit, Number of Three Seater Units (Nos)-1, Number of Four Seater Units (Nos) N Four Seater Unit, Frame Covering, Fully Upholstered, Backrest Cushion Material, Foam, Density of Cushion of Backrest Material (Kg/Cubic M)- 70, Covering Material for Seat and Backrest Leather Fabric, Frame Structure Material and size (±1 mm) Any other wood of minimum 25 mm thickness, Seat Cushion Material, Foam, Density of Cushion of Seat Material ±3 (Kg/Cubic M) 20, Type of Spring in the Base / Seating Eight way hand tied spring Length of Three Seater Units in mm (±10 mm)- 1750 Depth of Sofa Units in mm (±10 mm)- 700 Sofa Height (Without Back Cushion) ±5 (mm)- 430 millimeter Sofa Height (With Back Cushion) ±5 mm-775 millimeter Seat Cushion Length ±5 (mm)- 545, Seat Cushion Width ±5 (mm)-520, Seat Cushion Thickness ±3 (mm)- 65, Backrest Cushion Length ±5 (mm)-895, Backrest Cushion Width ±5 (mm)-508 as per satisfaction of engineer incharge.

TWF 2 Seater Sofa With Leatherite Cover, Frame Covering Fully Upholstered, Sofa Set is Foldable to use as bed-No, Backrest Cushion Material, Foam, Density of Cushion of Backrest Material (Kg/Cubic M)- 40, Covering Material for Seat and Backrest Leatherite, Frame Structure Material and size (±1 mm), Any other wood of minimum 25 mm thickness, Seat Cushion Material Foam,Density of Cushion of Seat Material ±3 (Kg/Cubic M) 40, Type of Spring in the Base / Seating Zig Zag spring, Length of Single Seater Units in mm (±5 mm) N.A, Length of Two Seater Units in mm (±10 mm) 1500, Length of Three Seater Units in mm (±10 mm) N.A, Length of Four Seater Units in mm (±10 mm) N.A, Depth of Sofa Units in mm (±10 mm)-950, Sofa Height (Without Back Cushion) ±5 (mm)- 600 millimeter, Sofa Height (With Back Cushion) ±5 mm, 850 millimeter, Seat Cushion Length ±5 (mm)-1050 Seat Cushion Width ±5 (mm)- 520, Seat Cushion Thickness ±3 (mm) 175, Backrest Cushion Length ±5 (mm)- 1050, Backrest Cushion Width ±5 (mm)- 508, as per satisfaction of engineer incharge.

HARLISON 1 Seater Sofa With Fabric Cover, Frame Covering Fully Upholstered, Sofa Set is Foldable to use as bed Backrest Cushion Material, Foam, Density of Cushion of Backrest Material (Kg/Cubic M)- 32, Covering Material for Seat and Backrest Fabric, Frame Structure Material and size (±1 mm), 19 mm thick Commercial board, Seat Cushion Material-Foam Density of Cushion of Seat Material ±3 (Kg/Cubic M)-30 Type of Spring in the Base / Seating- Zig Zag spring Length of Single Seater Units in mm (±5 mm)-800 Length of Two Seater Units in mm (±10 mm)-1370 Length of Three Seater Units in mm (±10 mm)-1850 Length of Four Seater Units in mm (±10 mm) -2640 Depth of Sofa Units in mm (±10 mm)-760 Sofa Height (Without Back Cushion) ±5 (mm)-550 millimeter Sofa Height (With Back Cushion) ±5 mm=650 millimeter Seat Cushion Length ±5 (mm)-640 Seat Cushion Width ±5 (mm)-510 Seat Cushion Thickness ±3 (mm)-100 Backrest Cushion Length ±5 (mm)-740 Backrest Cushion Width ±5 (mm)-508, as per satsas per satisfaction of engineer incharge.

SSFW Stainless Steel 304 Hot Display Counter, Capacity 40-50 Liter, (Hot Food Display Counter-40Ltr) Visibility in Hot display counter, Front cum Top, Counter Front Panel Shape, Flat No of Shelves- 4, Opening Door Position, Top- Opening Door Type Hinged, Features in Hot display counter-On/Off Switch, Material of Body, Stainless Steel 304, Material of Shelves,Stainless Steel 304 Material of Top Shelf, Stainless Steel 304, Material of Visibility Glass Toughen Glass, Capacity of Display Volume (in liter)- 40-50, Top Shelf width ( in MM )- 300, Minimum Thickness of Stainless steel Sheet(in mm),0.7, Minimum Thickness of Pre-coated GI Sheet(in mm), 0.7, Metal Surface Finish- Polish, as per satisfaction of engineer incharge.

Unbranded Die cast Aluminium Modern chandeliers 16 Watt, Wattage 16 Watt, Type- Modern chandeliers, Number of Light souce- 2, Lighting source life- 5000 hour, Material-Die cast Aluminium, Size(length)- 27 millimeter, Size(Width)-25 millimeter, as per satisfaction of engineer incharge.

HARLISON Executive Table with One side pedestal unit and E.R.U, (ET-1(3971514))Tabletop Material, Prelaminated particle board(Wood Product) of grade II type II of IS 12823/Lates, Thickness of table top, material (± 1 mm)- 25 mm, Gable end material, Prelaminated particles board(wood product) of grade II type III of IS 12823/Latest, The thickness of the gable end- 19 mm, Modesty panel material Three Layer Prelaminated particles board(wood product) of grade II type III of IS 12823/Latest, The thickness of the modesty panel material- 18 mm, - Width of tabletop ±10 mm 2100 mm Depth of table ±10 mm-1100 mm Height of table ±10 mm- 750 mm ERU unit consists of- 3 drawers ,2 storage units with shutter Total Number of drawers /storage in Pedestal units Three drawers, Table top finish Laminate in color with swede finish 0.6-0.8mm thickness of type S, F or P having index no.3.2.3 conforming to IS 2046/Latest with having balancing laminate of 0.5mm thick on another side Tabletop shade- Dark walnut Table /ERU /Pedestal Panel Plain Side All exposed edges sealed with 2 mm PVC edge banding tape and all unexposed edges sealed with 0.6mm edge banding tape pressed at 200 degrees C with hot melt glue, as per satisfaction of engineer incharge.

ZED Rectangular CENTRE TABLE with Other wood Top of 1200mmX600mm, (ZFCT-017), Top material Other wood- Frame material- Teak wood Dimension of Top (Length X Breadth, or Diameter) ±20mm- 1200mmX600mm, Height of centre table ±10 mm- 460 millimeter, Thickness of top material (+/-2 mm)- 25 millimeter Thickness of frame material (+/- 1 mm)- 25 millimeter, as per satisfaction of engineer incharge.

HARLISON N.A Credenzas (CREDENZAS-2(4464567)) Product id:5116877-90561779023, Mode of supply Knocked Down to be assembled at consignee site by the seller Design of credenza unit- Compartments(With Shelves) only Number of compartments with shelves, One Nos Number of shelves in each compartment- One Nos Number of partition for compartment- One Nos Type of doors for compartments- Sliding shutter Number of doors- Two Nos Material specification- Flat single layer prelaminated MDF board conforming to designation PLMDF-203 of IS 14587/Latest having balancing laminated of 0.5mm thick on other side Material thickness of complete body,Fascia and drawer/compartment 25 millimeter, Material thickness for back, partition and drawer bottom/compartment shelves ±2mm- 25 millimeter Skirting Thickness- 12 millimeter, All plain panels edge to be banded With 0.8-1.0 mm thick PVC tape with the help of hot melt glue, Width of credenza unit ± 20mm- 1600 mm Height of credenza unit ±20 mm- 750 mm Depth of credenza unit ±20mm- 510 mm Locking System provided- YES Warranty period in number of years-1 Test reports to be furnished to buyer on demand- YES OEM of offered product is ISO 9001:2015 certified- YES OEM of offered product is ISO 14001:2015 certified- YES OEM of offered product is ISO 18001:2007/45001:2018 certified- YES, as per satisfaction of engineer incharge.

V J Interior Plastic Moulded Chair With Arms With Cushion Single Piece Plastic Moulded (KWEPL-B239-B1) Product id: 5116877-37108939391, Type of Chair Single Piece Plastic Moulded- Seat Cushion, With, Back Cushion With, Plastic Material, Polypropylene, Arms, With Arms, Seat Width in mm (+/- 5 mm), 415, Seat Depth in mm (+/- 5 mm) 410, Thickness of Polyurethane Foam Used in Seat in mm (+/- 2 mm), 40, Density of PU Foam in KG per Cum 40 GSM/Thickness of Fabric (Gram per Sq Meter) 240 gsm, Thickness of Polyurethane Foam Used in Backrest in mm (+/- 2 mm) 40, Support/Under Structure Single Moulded Piece No Support Structure, Support Structure Finishing, Sigle Moulded Piece No Support Structure as per satisfaction of engineer incharge.

geeken MODULAR TABLE L X D & H 2400 millimeter X 750 millimeter 800 millimeter (Geeken RECEPTION 1 W2400 X D820 X H1000) Product id: 5116877-56413630709, Mode of Supply of modular table, Knocked Down to be assembled at consignee site by the Seller Storage Provided- No Storage Number of storage unit- No Storage Table Top material and thickness ±3mm 43mm thickness three layer pre-laminated Particle boards (Wood Product) of grade II Type II of IS 12823 Latest Gable end and modesty panel material and thickness 18 mm thickness three layers pre-laminated Particle boards (Wood Product) of grade II Type III of IS 12823 Latest Length of Table Top ±10(mm), 2400 millimeter, Depth of Table Top±10(mm)- 750 millimeter Height of Table Top±10(mm)- 800 millimeter, as per satisfaction of engineer incharge.

geeken REVOLVING Counter Chair, (COUNTER CHAIR) Product id:- 5116877-27335615700, Height Adjustment With Hydraulic, Frame and support made of, SS 304, Chair Type REVOLVING, TYPE OF SEATING, SEAT WITH SEPERATE BACKREST, Padestal Base- Stainless Steel Foot Rest, With Padestal Base Type With minimum 5 Nos ABS/Nylon Twin Caster wheels Arms WithoutMAX LOAD BEARING CAPACITY IN KG 90, as per satisfaction of engineer incharge.

geeken 1 Seater Sofa With Leatherite Cover, (FLAMINGO 1 SINGLE SEATER SOFA) Product id:- 5116877-71935410565, Total Number of Seats in the Sofa Set- 1 Number of Single Seater Units (Nos)- 1 Number of Two Seater Units (Nos)- No Two Seater Unit Number of Three Seater Units (Nos) No Three Seater Unit Number of Four Seater Units (Nos) No Four Seater Unit Frame Covering Fully Upholstered Sofa Set is Foldable to use as bed No Backrest Cushion Material Foam Density of Cushion of Backrest Material (Kg/Cubic M) 32 Covering Material for Seat and Backrest Leatherite Frame Structure Material and size (±1 mm) Any other wood of minimum 25 mm thickness Seat Cushion Material FoamDensity of Cushion of Seat Material ±3 (Kg/Cubic M) 35 Type of Spring in the Base / Seating Web suspension Length of Single Seater Units in mm (±5 mm) 850 Length of Three Seater Units in mm (±10 mm) Depth of Sofa Units in mm (±10 mm)- 800 Sofa Height (Without Back Cushion) ±5 (mm) 700 millimeter Sofa Height (With Back Cushion) ±5 mm 600 millimeter, Seat Cushion Length ±5 (mm)- 525, Seat Cushion Width ±5 (mm)- 710 Seat Cushion Thickness ±3 (mm) 125, Backrest Cushion Length ±5 (mm)- 710, Backrest Cushion Width ±5 (mm)- 710,as per satisfaction of engineer incharge.

geeken 2 Seater Sofa With Leatherite Cover, (Geeken (Lider-2) 1720 (L) X 900 (D) X 820 (H)mm), Product id: 5116877-14809014215, Total Number of Seats in the Sofa Set- 2 Number of Single Seater Units (Nos) No Single Seater Unit Number of Two Seater Units (Nos)- 1 Number of Three Seater Units (Nos) No Three Seater Unit Number of Four Seater Units (Nos) No Four Seater Unit Frame Covering, Fully Upholstered Backrest Cushion Material, Foam- Density of Cushion of Backrest Material (Kg/Cubic M)- 32 Covering Material for Seat and Backrest- Leatherite Frame Structure Material and size (±1 mm)- 19 mm thick Commercial board Seat Cushion Material- Foam Density of Cushion of Seat Material ±3 (Kg/Cubic M)- 40 Type of Spring in the Base / Seating- Zig Zag spring Length of Two Seater Units in mm (±10 mm)- 1600 Depth of Sofa Units in mm (±10 mm)- 900 Sofa Height (Without Back Cushion) ±5 (mm)- 430 millimeter Sofa Height (With Back Cushion) ±5 mm- 800 millimeter Seat Cushion Length ±5 (mm)- 350 Seat Cushion Width ±5 (mm)- 380 Seat Cushion Thickness ±3 (mm)- 65 Backrest Cushion Length ±5 (mm)- 530 Backrest Cushion Width ±5 (mm)- 335, as per satisfaction of engineer incharge.

geeken 3 Seater Sofa With Leatherite Cover, (Geeken (Lider-3) 2310 (L) X 900 (D) X 820 (H)mm), Product id: 5116877-69711659282, Total Number of Seats in the Sofa Set- 3 Two Seater Unit, umber of Three Seater Units (Nos)-1, Number of Four Seater Units (Nos), Four Seater Unit, Frame Covering, Fully Upholstered, Backrest Cushion Material Foam- Density of Cushion of Backrest Material (Kg/Cubic M)- 32, Covering Material for Seat and Backrest Leatherite, Frame Structure Material and size (±1 mm), 19 mm thick Commercial board, Seat Cushion Material Foam- Density of Cushion of Seat Material ±3 (Kg/Cubic M)- 40 Type of Spring in the Base / Seating- Zig Zag spring .Length of Three Seater Units in mm (±10 mm)- 2230 Depth of Sofa Units in mm (±10 mm)- 900 Sofa Height (Without Back Cushion) ±5 (mm)- 430 millimeter Sofa Height (With Back Cushion) ±5 mm- 800 millimeter Seat Cushion Length ±5 (mm)- 350 Seat Cushion Width ±5 (mm)- 380 Seat Cushion Thickness ±3 (mm)- 65 Backrest Cushion Length ±5 (mm)- 530 Backrest Cushion Width ±5 (mm)- 335, as per satisfaction of engineer incharge.

geeken Rectangular CENTRE TABLE with Medium Density Fiberboard Top of 1194mmX584mm, (ZAP CENTRE TABLE), Product id: 5116877-39686003717, Top material Medium Density Fiberboard, Frame material, MILD STEEL, Dimension of Top (Length X Breadth, or Diameter) ±20mm 1194mmX584mm, Height of centre table ±10 mm- 410 millimeter, Thickness of top material (+/-2 mm)- 12 millimeter, as per satisfaction of engineer incharge.

geeken Rectangular CENTRE TABLE with Commercial Block Board BWP grade Conforming to IS 1659 Top of 609mm(Dia)(ZAP CENTER TABLE 600*600 )Product id: 5116877-58757901277, Number of storage under top Double storage (one at upper portion and one at bottom portion) Top material- Commercial Block Board BWP grade Conforming to IS 1659, Frame material- MILD STEEL Dimension of Top (Length X Breadth, or Diameter) ±20mm- 609mm(Dia), Height of centre table ±10 mm- 460 millimeter Thickness of top material (+/-2 mm)- 18 millimeter Thickness of frame material (+/- 1 mm)- 8 millimeter, as per satisfaction of engineer incharge.

geeken Rectangular CENTRE TABLE with Toughened glass Top of 1200mmX600mm, (Alice Centre table), Product id: 5116877-28702046086, Number of storage under top Single storage in bottom portion, Top material, Toughened glass, Frame material, Stainless steel SS 304, Dimension of Top (Length X Breadth, or Diameter) ±20mm- 1200mmX600mm Height of centre table ±10 mm- 485 millimeter Thickness of top material (+/-2 mm)- 12 millimeter, Thickness of frame material (+/- 1 mm)- 36 millimeter, as per satisfaction of engineer incharge.

geeken Rectangular CENTRE TABLE with Commercial Block Board BWP grade Conforming to IS 1659 Top of 609mm(Dia)(ZAP CENTER TABLE 600*600 )Product id: 5116877-58757901277, Number of storage under top Double storage (one at upper portion and one at bottom portion) Top material- Commercial Block Board BWP grade Conforming to IS 1659, Frame material- MILD STEEL Dimension of Top (Length X Breadth, or Diameter) ±20mm- 609mm(Dia), Height of centre table ±10 mm- 460 millimeter Thickness of top material (+/-2 mm)- 18 millimeter Thickness of frame material (+/- 1 mm)- 8 millimeter, as per satisfaction of engineer incharge.

geeken 1 Seater Sofa With Leatherite Cover, (FLAMINGO 1 SINGLE SEATER SOFA) Product id: 5116877-71935410565, Total Number of Seats in the Sofa Set-1 Number of Single Seater Units (Nos)- 1,Four Seater Unit Frame Covering, Fully Upholstered Backrest Cushion Material, Foam Density of Cushion of Backrest Material (Kg/Cubic M)-32 Covering Material for Seat and Backrest, Leatherite Frame Structure Material and size (±1 mm) Any other wood of minimum 25 mm thickness Seat Cushion Material, Foam, Density of Cushion of Seat Material ±3 (Kg/Cubic M)-35 Type of Spring in the Base / Seating- Web suspension Length of Single Seater Units in mm (±5 mm)-850 Depth of Sofa Units in mm (±10 mm)-800 Sofa Height (Without Back Cushion) ±5 (mm)- 700 millimeter Sofa Height (With Back Cushion) ±5 mm- 600 millimeter Seat Cushion Length ±5 (mm)- 525 Seat Cushion Width ±5 (mm)- 710 Seat Cushion Thickness ±3 (mm)- 125 Backrest Cushion Length ±5 (mm)- 710 Backrest Cushion Width ±5 (mm)- 710, as per satisfaction of engineer incharge.

geeken 3 Seater Sofa With Leatherite Cover, (Geeken (Lider-3) 2310 (L) X 900 (D) X 820 (H)mm),Product id: 5116877-69711659282, Total Number of Seats in the Sofa Set 3, Single Seater Unit, Number of Two Seater Units (Nos) No Two Seater Unit, Number of Three Seater Units (Nos) 1 , Four Seater Unit, Frame Covering Backrest Cushion Material, Foam, Density of Cushion of Backrest Material (Kg/Cubic M)- 32 Covering Material for Seat and Backrest, Leatherite Frame Structure Material and size (±1 mm) 19 mm thick Commercial board Seat Cushion Material, Foam, Density of Cushion of Seat Material ±3 (Kg/Cubic M)- 40 Type of Spring in the Base / Seating- Zig Zag spring Length of Three Seater Units in mm (±10 mm)- 2230 Depth of Sofa Units in mm (±10 mm)- 900 Sofa Height (Without Back Cushion) ±5 (mm)- 430 millimeter Sofa Height (With Back Cushion) ±5 mm- 800 millimeter Seat Cushion Length ±5 (mm)- 350 Seat Cushion Width ±5 (mm)- 380 Seat Cushion Thickness ±3 (mm)- 65 Backrest Cushion Length ±5 (mm)- 530 Backrest Cushion Width ±5 (mm)- 335, as per satisfaction of engineer incharge.

GODREJ INTERIO Revolving Chair with Swivel tilt mechanism, (GODREJ INTERIO PREMIER HIGH BACK CHAIR) Product id: 5116877-41778146759 Tilt mechanism, Swivel tilt mechanism Locking mechanism, Upright locking, Armrest type and arm movement Hint: The buyer may indicate the number of ‘Up’ and ‘Down’ arm movements at the time of bid creation, Fixed Backrest type, Tilting type, Pedestal Base, Mild Steel Armrest Material, MS Arms with ABS arm top, Minimum density of, foam used in seat- 30 kg per cubic meter Minimum thickness of PU foam used in seat- 30 mm Seat upholstery material 100 % Polyester fabric Backrest base frame material- Hot pressed plywood Padding at backrest, PU foam The minimum density of foam used in the backrest, 30 kg per cubic meter- Minimum thickness of PU foam used in backrest- 30 mm, Backrest upholstery material, 100 % Polyester fabric Upholstery material thickness /fabric substance used in seat /backrest, Minimum 200 GSM (for Woven fabric) Minimum width of seat, 450 mm, Minimum depth of seat 400 mm, Minimum width of backrest- 450 mm, Backrest height, High back (551 and above) Minimum thickness of MS Plate Joining the understructure with- Seat, 2 mm, Minimum pedestal size (diameter)- 650 mm Upholstered material seat color- Grey, Upholstered material backrest color- Grey, as per satisfaction of engineer incharge.

GODREJ INTERIO Non-Revolving and Non-Tilting chair with Armrest, (GODREJ INTERIO VERSA CANVAS VISITOR CHAIR) Product id:- 5116877-5484716932, Chair Type Non-Revolving and Non-Tilting chair with Armrest Chair frame type, Cantilever, Armrest type, Continuous armrest Seat type, Padded, Backrest type, Padded, Frame Material Configuration, One piece, Frame material Steel tube (ERW quality) conforming to IS: 1161 (with latest, Amendment), Seat material, Moulded Plywood ,Seat material thickness- 40 mm, Density of Polyurethane foam used in seat (±2 Kg/Cub Meter)- 45 Seat upholstered with, Fabric GSM of seat cover (± 3 GSM) 220 GSM Backrest material, Single piece of Cold Reduced Carbon Steel Sheet Confmg. to grade CR0 of IS:513 part 1 (with Latest amendment), ensity of Polyurethane foam used in Backrest ( ±2 Kg/Cub Meter)- 45 Backrest upholstered with Fabric Seat Depth (± 5 mm)- 480 mm Seat Width (± 5 mm)- 460 mm, Seat height from floor surface (± 5 mm)- 435 mm Backrest width (± 5 mm)- 450 mm Backrest height from seat (± 5 mm)- 480 mm, Paint Type- Epoxy Colour of Paint, Black, Availability of Test Report from Central Govt/NABL/ILAC accredited lab to prove the conformity of product to the Specification- Yes, Test reports to be furnished to buyer on demand- Yes, as per satisfaction of engineer incharge.

conference table Product id: 5116877-35964492694 SELLING UNIT SELLING UNIT IS PER SEAT. SELLER TO OFEER PRICES IN TREMS OF PRICE PER SEAT. WHILE ORDERING, BUYER TO ORDER FOR QUANTITY OF SEATS REQUIRED IN CONFERENCE TABLE. Type of Seating Offered Dual Seating Top Fixing With gable end and modesty panel using Mini Fix And Wooden Dowel By Using (Knock Down) System For Interconnecting Number of single seater N.A Number of dual seater 6 Number of corners for work top 1 Mode of Supply of modular table Knocked Down To Be Assembled At Consignee Site By The SellerMaterial of work top ± 3 mm 36 Mm Thick Flat Single Layer MDF Board Of Grade SBG-II Of IS:12406/Latest Table top plain side Edge banded with PVC tape of 2 mm thick with help of hot melt glue Material of Gable end and modesty panel ±3 mm 18 Mm Thick Three Layers Prelaminated Particle Boards Of Grade-II Type-III Of IS:12823/Latest Both Sides Particle Boards Matching With Top Shade In Grade-II Type-III Length of Each Seat of Work Top ± 20 mm 675 mm for single AND 1350 mm For dual Depth of Work Top ± 20 mm 750 mm Table top finish Laminate In Colour With matt Finish 0.6-0.8 Mm Thickness Of Type S,F Or P Having Index Number 3.2.3 Conforming To IS:2046/Latest With Having Balancing Laminate Of 0.5 Mm Thick On Other Side Colour of top finish As per buyer's choice Warranty period in number of years 1 Test reports to be furnished to buyer on demand YES OEM of offered product is ISO 9001:2015 certified YES OEM of offered product is ISO 14001:2015 certified YES OEM of offered product isISO18001:2007/45001:2018 certifiedYES Product having BIFMA certificationNO as per satisfaction of engineer incharge

sofa conference table Product id: 5116877-88897139534 Total Number of Seats in the Sofa Set 3 Number of Single Seater Units (Nos) No Single Seater Unit Number of Two Seater Units (Nos) No Two Seater Unit Number of Three Seater Units (Nos) 1 Number of Four Seater Units (Nos) No Four Seater Unit Frame Covering Fully Upholstered Sofa Set is Foldable to use as bed No Backrest Cushion Material Foam Density of Cushion of Backrest Material (Kg/Cubic M) 32 Covering Material for Seat and Backrest Leather Fabric Frame Structure Material and size (±1 mm) 19 mm thick Commercial board Seat Cushion Material Foam Density of Cushion of Seat Material ±3 (Kg/Cubic M) 35Type of Spring in the Base / Seating Web suspension Length of Single Seater Units in mm (±5 mm) N.A Length of Two Seater Units in mm (±10 mm) N.A Length of Three Seater Units in mm (±10 mm) 1750 Length of Four Seater Units in mm (±10 mm) N.A Depth of Sofa Units in mm (±10 mm) 900 Sofa Height (Without Back Cushion) ±5 (mm) 450 millimeter Sofa Height (With Back Cushion) ±5 mm850 millimeter Seat Cushion Length ±5 (mm) 1200Seat Cushion Width ±5 (mm)510Seat Cushion Thickness ±3(mm)100Backrest Cushion Length ±5 (mm)1450Backrest Cushion Width ±5 (mm) 508Warranty1 - Year as per satisfaction of engineer incharge

side table 600x600 Product id: 5116877-88640301237 Number of storage under top Single storage in bottom portion Top material Medium Density Fiberboard Frame material MILD STEEL Dimension of Top (Length X Breadth, or Diameter) ±20mm 914mmX609mm Height of centre table ±10 mm 460 millimeter Thickness of top material (+/-2 mm) 18 millimeter Thickness of frame material (+/- 1 mm) 19 millimeter Warranty period in number of years 1 as per satisfaction of engineer incharge

CM Equivalent office table geeken 2400 mm 1110 mm 730 mm, Product id: 5116877-36398625432 Warranty periods 1 – Year Design / Shape Rectangular Under structure of main table Gable end modesty panel Table top material 2 MDF batons with natural veneer Gable end material MDF board as per IS: 12406 with pigmented PU coating on both sides Modesty panel material MDF board as per IS: 12406 with pigmented PU coating on both sides Leg material MS Clad with strips of MDF Number of buffer provided Four numbers at bottom Length of table top ± 20 mm 2400 mm Depth of table top ±10 mm 1110 mm Height of table top ± 10 mm 730 mm Dimension of leg ± 2 mm NAThickness of table top ± 2 mm 40 mm Thickness of gable end ± 2 mm 18 mm Thickness of modesty panel ± 1 mm 18 mm Material of keyboard tray and right angle L-Type supporting bracket N.A Finish of exposed edges of keyboard tray N.A Number of storage unit 1 number Storage with shutter N.A Number of drawers 1 number Size of small drawers ± 5 mm 150 mm (H) X 465 mm(W) X 470 mm(D) Size of medium drawers ± 5 mm 300 mm(H) X 465 mm(W) X 470 mm(D) Number of lockable castors at bottom 4 numbers Size of lockable castors ± 2 mm Diameter 30 mm and height 50 mm Provision of storage lock system Central locking system Material of top 2 MDF batons with natural veneer Material of modesty panel MDF board as per IS: 12406 with pigmented PU coating on both sides Material of side panel MDF board as per IS: 12406 with pigmented PU coating on both sides Thickness of top panel ± 2 mm 40 mm Thickness of other panel ± 2 mm 18 mm Thickness of drawer base ± 1 mm 10 mm Width of unit ± 20 mm 1400 mm Depth of unit ± 5 mm 580 mm Height of unit ± 5 mm 690 mm Overall height of storage unit ± 5 mm 690 mm Type of unit Three drawers Size of drawers ± 2 mm 162 mm (H) x 640 mm (D) x 480 mm (W) Each drawers fixed with On telescopic channel of 250 mm length with average weight of 0.5 Kg per set having average thickness of 1 mm steel member of channel Provision of lock system Central locking system Material of top panel MDF board as per IS: 12406 with pigmented PU coating on both sides Material of other panel MDF board as per IS: 12406 with pigmented PU coating on both sides Thickness of top panel ± 1 mm 19 mm Thickness of other panel ± 1 mm 18 mm Number of lockable castors at bottom pedestal storage unit 4 numbers Size of lockable castors for pedestal storage unit ± 2 mm Diameter 30 mm and height 50 mm Width of pedestal unit ± 5 mm 440 mm Depth of pedestal unit ± 5 mm 510 mm Height of pedestal unit ± 5 mm 580 mm Total Number of shelf 5 numbers Top panel material MDF board, pigmented black & coated with melamine Side panel material MDF board, pigmented black & coated with melamine Shelf material MDF board, pigmented black & coated with melamine Full Door panel material N.A Upper door panel made up of N.A Lower door panel made up of MD batons with veneer coating Thickness of top panel material ± 1 mm 18 mm Thickness of side panel material ± 1 mm 18 mm Thickness of shelf panel material ± 1 mm 18 mm Thickness of door panel (full size) material ± 1 mm N.A Thickness of upper door panel made up of ± 1 mm N.A Thickness of lower panel made up of ± 1 mm 18 mm Material for buffer N.A Width of book case ± 10 mm 1850 mm Depth of book case ± 5 mm 580 mm Height of book case ± 20 mm 1880 mm Size of medium shelf 1 number Product having BIFMA certification No OEM of offered product is ISO 9001:2015 certified Yes OEM of offered product is ISO 14001:2015 certified Yes OEM of offered product is ISO 18001:2007/45001:2018 certified Yes as per satisfaction of engineer incharge

cm office Main chair Product id: 5116877-34172896892 Tilt mechanism Synchronic tilt mechanism Locking mechanism Tilt limiter Armrest type and arm movement Hint: The buyer may indicate the number of ‘Up’ and ‘Down’ arm movements at the time of bid creation Adjustable (up and down) Backrest typeTilting type Pedestal BaseAluminium die Cast Armrest MaterialPU molded over metal insert Minimum density of foam used in seat 30 kg per cubic meter Minimum thickness of PU foam used in seat 30 mmSeat upholstery material Leather Backrest base frame materialHot pressed plywoodPadding at backrest PU foam The minimum density of foam used in the backrest 30 kg per cubic meter Minimum thickness of PU foam used in backrest 30 mm Backrest upholstery material Leather Upholstery material thickness /fabric substance used in seat /backrest 0.7 to 1.5 mm (for leather /leatherette) Minimum width of seat 500 mm Minimum depth of seat 450 mm Minimum width of backrest 450 mm Backrest height High back (551 and above) Minimum thickness of MS Plate Joining the understructure with Seat 2 mm Minimum pedestal size (diameter) 650 mm Upholstered material seat color Brown Upholstered material backrest color Brown VIEW LESS as per satisfaction of engineer incharge

CM office 5 seater sofa Product id: 5116877-71660418263 Total Number of Seats in the Sofa Set 5 Number of Single Seater Units (Nos) No Single Seater Unit Number of Two Seater Units (Nos) 2 Number of Three Seater Units (Nos) 1 Number of Four Seater Units (Nos) No Four Seater Unit Frame Covering Fully Upholstered Sofa Set is Foldable to use as bed No Backrest Cushion Material Foam Density of Cushion of Backrest Material (Kg/Cubic M) 32 Covering Material for Seat and BackrestLeatherite Frame Structure Material and size (±1 mm)19 mm thick Commercial board Seat Cushion Material Foam Density of Cushion of Seat Material ±3 (Kg/Cubic M) 35 Type of Spring in the Base / SeatingZig Zag spring Length of Single Seater Units in mm (±5 mm) 400 Length of Two Seater Units in mm (±10 mm) 800 Length of Three Seater Units in mm (±10 mm) 1200 Length of Four Seater Units in mm (±10 mm) N.A Depth of Sofa Units in mm (±10 mm) 400 Sofa Height (Without Back Cushion) ±5 (mm) 400 millimeter Sofa Height (With Back Cushion) ±5 mm 600 millimeter Seat Cushion Length ±5 (mm) 350 Seat Cushion Width ±5 (mm) 380 Seat Cushion Thickness ±3 (mm) 65 Backrest Cushion Length ±5 (mm) 530 Backrest Cushion Width ±5 (mm) 335 Warranty 1 - Year as per satisfaction of engineer incharge

CM Equivalent Back unit Product id: 5116877-32916515574 Mode of supply Knocked Down to be assembled at consignee site by the seller Design of credenza unit Compartments(With Shelves) only Number of drawers N.A Number of compartments with shelves Three Nos Number of shelves in each compartmentOne Nos Number of compartment without shelves N.A Number of partition for compartment Two Nos Number of compartment in each partition N.A Type of doors for compartments Shutter hung on side Number of doors Three Nos Material specification Flat single layer prelaminated MDF board conforming to designation PLMDF-203 of IS 14587/Latest having balancing laminated of 0.5mm thick on other side Material thickness of complete body,Fascia and drawer/compartment 19 millimeter Material thickness for back, partition and drawer bottom/compartment shelves ±2mm 19 millimeter Skirting Thickness 19 millimeter All plain panels edge to be banded With 0.8-1.0 mm thick PVC tape with the help of hot melt glue Width of credenza unit ± 20mm 1200 mm Height of credenza unit ±20 mm 1800 mm Depth of credenza unit ±20mm 510 mm Locking System provided YES Warranty period in number of years 1 Test reports to be furnished to buyer on demand YES Product having BIFMA certification NO OEM of offered product is ISO 9001:2015 certified YES OEM of offered product is ISO 14001:2015 certified YES OEM of offered product is ISO 18001:2007/45001:2018 certified YES as per satisfaction of engineer incharge

cm office Main chair Product id: 5116877-34172896892 Tilt mechanism Synchronic tilt mechanism Locking mechanism Tilt limiter Armrest type and arm movement Hint: The buyer may indicate the number of ‘Up’ and ‘Down’ arm movements at the time of bid creation Adjustable (up and down) Backrest typeTilting type Pedestal BaseAluminium die Cast Armrest MaterialPU molded over metal insert Minimum density of foam used in seat 30 kg per cubic meter Minimum thickness of PU foam used in seat 30 mmSeat upholstery material Leather Backrest base frame materialHot pressed plywoodPadding at backrest PU foam The minimum density of foam used in the backrest 30 kg per cubic meter Minimum thickness of PU foam used in backrest 30 mm Backrest upholstery material Leather Upholstery material thickness /fabric substance used in seat /backrest 0.7 to 1.5 mm (for leather /leatherette) Minimum width of seat 500 mm Minimum depth of seat 450 mm Minimum width of backrest 450 mm Backrest height High back (551 and above) Minimum thickness of MS Plate Joining the understructure with Seat 2 mm Minimum pedestal size (diameter) 650 mm Upholstered material seat color Brown Upholstered material backrest color Brown VIEW LESS as per satisfaction of engineer incharge

CM office 5 seater sofa Product id: 5116877-71660418263 Total Number of Seats in the Sofa Set 5 Number of Single Seater Units (Nos) No Single Seater Unit Number of Two Seater Units (Nos) 2 Number of Three Seater Units (Nos) 1 Number of Four Seater Units (Nos) No Four Seater Unit Frame Covering Fully Upholstered Sofa Set is Foldable to use as bed No Backrest Cushion Material Foam Density of Cushion of Backrest Material (Kg/Cubic M) 32 Covering Material for Seat and BackrestLeatherite Frame Structure Material and size (±1 mm)19 mm thick Commercial board Seat Cushion Material Foam Density of Cushion of Seat Material ±3 (Kg/Cubic M) 35 Type of Spring in the Base / SeatingZig Zag spring Length of Single Seater Units in mm (±5 mm) 400 Length of Two Seater Units in mm (±10 mm) 800 Length of Three Seater Units in mm (±10 mm) 1200 Length of Four Seater Units in mm (±10 mm) N.A Depth of Sofa Units in mm (±10 mm) 400 Sofa Height (Without Back Cushion) ±5 (mm) 400 millimeter Sofa Height (With Back Cushion) ±5 mm 600 millimeter Seat Cushion Length ±5 (mm) 350 Seat Cushion Width ±5 (mm) 380 Seat Cushion Thickness ±3 (mm) 65 Backrest Cushion Length ±5 (mm) 530 Backrest Cushion Width ±5 (mm) 335 Warranty 1 - Year as per satisfaction of engineer incharge

WALL PAPER , as per satisfaction of engineer incharge.

UTTAM--M/S UTTAM UDYOG Handloom Cotton Bed Sheets as per IS 745 Variety No - 12 (140 g) of Size 229 x 140 cm, Unregistered Brand, Manufactured by: M/S UTTAM UDYOG (Handloom Cotton Bed Sheets) Technical Specification of the Product- Handloom Cotton Bed Sheets as per BIS Specification No. IS 745:2021 (Latest) Variety as per BIS specification (Mass in gram per square meter) Variety No - 12 (140 g), Size (Length x Width) (cm x cm) 229 x 140, Logo/ Totem Marking Size, Design, Type and Location of Logo(s) as per buyer's requirement, Screen Printed Identification Marking (longitudinal Running Strips), As per buyer's requirement Handloom Mark- Yes, as per satisfaction of engineer incharge.

Flat Bedsheet Premium 800 TC 100% Egyptian Cotton Flat Bedsheet for Single Size Bed | 1 Bedsheets with 2 Pillow Covers | Bed Sheet | Chadar Bed | Chadar - Single Bed_White Solid with 800 TC, Size Single Size, Material Cotton, Colour White Solid, Pattern Solid, Brand KEDARA CLOTH, Included Components 1 Flat Sheet And 2 Pillowcases, Thread Count 800, Age Range (Description) Adult, Occasion Housewarming, Product Care Instructions Machine Wash, Fill Material ‎पॉलिएसटर Colour ‎White, Size ‎Standard Brand ‎JDX, Shape ‎Square, Special Feature ‎Washable Cover Material ‎Microfiber, Pattern ‎Striped Age Range (Description) ‎Adult, Number of Items ‎5, Product Dimensions ‎40L x 40W Centimeters, Style ‎Modern, Item Firmness Description ‎Soft, Theme ‎Striped, Thread Count ‎190 Item Weight ‎900 Grams, Net Quantity ‎5 count, Color ‎White tem Model Number ‎JPCUSHIONJDX66_71003-5-16x16 Inches_BD Item Part Number ‎JPCUSHIONJDX66_71003-5-16x16 Inches_BD Primary material ‎Synthetic, Upholstery material ‎Microfiber Capacity ‎Standard, Number of Pieces ‎5, What is in the box? ‎Micro fibre silknise cushion filler, 40x40cms, set of 5, Manufacturer ‎JDX online sales, as per satisfaction of engineer incharge.

GODREJ INTERIO Pillow - Synthetic, (GODREJ INTERIO APOLLO PILLOW) Product id: 5116877-80626987231, as per satisfaction of engineer incharge.

JDX Micro Fibre Silknise Cushion Filler (40X40cms, White), Fill Material पॉलिएसटर, Colour White, Size Standard Brand JDX, Shape Square, Special Feature Washable Cover Material Microfiber, Pattern Striped, Age Range (Description) Adult, as per satisfaction of engineer incharge.

Trendy Retail Thicken double Lamb Velvet Blanket Luxurious Velvet Lamb Wool for Bedroom Nursery Gray Brown, Material plush Colour Gray, Brand Trendy Retail Special Feature Skin Friendly, Breathable Style Modern, Age Range (Description) Kid Product Dimensions 152L x 127W Centimeters ,Pattern Solid, as per satisfaction of engineer incharge.

Trendy Retail Thicken Lamb Velvet Blanket Luxurious Velvet Lamb single size blanket Wool for Bedroom Nursery Gray Brown, Material plush Brand Trendy Retail Special Feature Skin Friendly, Breathable Style Modern, Age Range (Description) Kid Pattern Solid, as per satisfaction of engineer incharge.

Wooden Bookshelf for Living Room Solid Wood 1 Door Book Case Shelf with Storage with Home,Office & Study Room,Teak Finish (Brown) (Brown Netural), with glass, Brand ALATERRE HOME FURNITURE Colour Brown Netural Material Sheesham Wood Recommended Uses For Product Crockery Product Dimensions 55D x 35W x 180H Centimeters pecial Feature Heavy Duty Mounting Type Floor Mount Room Type Living Room Home & Officeoor Style Open Frame Included Components Wooden Book Shelf For Living Room Cebinetas per satisfaction of engineer incharge.

AALMIN CARPET Microfiber Super Soft Handwoven Plain shag Size 8X10 Feet. Brand AALMIN CARPET, Size 8 x 10 Feet, Material MICOR FIBER, Weave Type Knotted, Item Weight 30 Kilograms, Pile Height 2 INCH, Construction Type Handmade Back Material Type Cotton, Colour SILVER, Indoor/Outdoor Usage Indoor, as per satisfaction of engineer incharge.

SITC of Digital signal processor with min. 08 AEC enabled Mic/Line inputs, 08 Line outputs or better , Input channel processing should include Pre amplifier, Signal generator, Expander, Compressor, 10 band Parametric EQ or better, Output Channel processing should include 31 band Graphic equilizer, Delay, Crossover, limiter or better, Other features should include Automatic mixing console, Ducker, Feedback elimination, Noise elimination, echo elimination or better, Should have built-in Bi directional USB for Software based VC as well as for playing digital audio, Should have built in Camera tracking Module, 8 Port Freely Configurable GPIO or better with Analog/Digital dynamic range of 114dB or better, Sampling rate of 48Khz or better, Frequency response of 20Hz – 20Khz or better, per channel phantom power module or better. Should be configurable thru software.as per satisfaction of engineer incharge.

WORKPRO SITC of 2 way passive Ceiling Speaker with 6.5” Woofer coaxial with 0.5" tweeter with Sensitivity 88db at 1 watt at 1 mtr. Frequency Response from 90Hz to 20KHz. Maximum Power 30 Watt at 70/100 Volt Power Taps. Coverage angle of Speaker will be 155º x 155º @ 1 KHz; 75º x 75º @ 4 KHz. Max SPL will be 102 db. Material will be Metal; Grille: ABS plastic and Colour is White (RAL9016), as per satisfaction of engineer incharge.

WORKPRO SITC of Dual Channel class D amplifier with 230 watt @2 ohm .20 Hz - 20 KHz, SUB mode: cut-off frequency between 50 Hz and 250 Hz . Amplifier signal to noise ration will be greater than 94 db . Gain to signal will be 28 db with input sensitivity will be 2.2dbu Input Power Supply will be 100-250 Volt AC at 50/60 Hz, as per satisfaction of engineer incharge.

Chairman Unit - Desktop base discussion microphone, Engineered in high-quality copper-zinc alloys die cast. The chairman microphone connects to the central control unit via network category 5 cable. Shotgun Gooseneck microphone with cardioid unidirectional pickup capsule. Speaking status indicator: red when mute, green when speaking. Chairman unit has the priority to override all delegate units. Cardioid Condenser Microphone with Freq response of 50Hz - 20 Khz, Sensitivity of -20db+/-3db, Max SPL of 110dB, Chairman unit having Mute/Unmute button with Priority switch for Muting all the delegates. Power supply - 24 VDC supplied by the receiver, as per satisfaction of engineer incharge.

EARTHPOT Delegate Unit - Desktop base discussion microphone. A desktop discussion microphone unit engineered in high-quality copper-zinc alloys die cast. The Delegate microphone connects to the central control unit via network category 5 cable. Shotgun Gooseneck microphone with cardioid unidirectional pickup capsule. The microphone with illuminating ring indicates the active status. The Delegate unit has a mute switch button . Cardioid Condenser Microphone with Freq response of 50Hz - 20 Khz, Sensitivity of -20db+/-3db,Max SPL of 110dB Delegate unit having Mute/Unmute button. Power supply - 24 VDC supplied by the receiver, as per satisfaction of engineer incharge.

ATEN 4x2 Matrix Switcher for HDMI Output as per satisfaction of engineer incharge.

LOGIC CABLE Cubby for HDMi Output, as per satisfaction of engineer incharge.

LOGIC HDMI Extender,as per satisfaction of engineer incharge.

LOGITECH Really PLUS PTZ Camera, as per satisfaction of engineer incharge.

PROJECTION Screen ALR 4K 150" Fixed ,as per satisfaction of engineer incharge.

OPTOMA ZH507 5500 Lumens Projector,as per satisfaction of engineer incharge.

CONFERENCE Room Table 24x16x2.5 Sqft, as per satisfaction of engineer incharge.

MOTORISED Wooden Finish BLINDS with Remote 4200x3 Sqft, as per satisfaction of engineer incharge.

Wooden Ceiling Work with Acoustics, Veener Finsh 1280Sqft, as per satisfaction of engineer incharge.

CARPET Tiles 1x1 with Hitlon Foam 6mm,as per satisfaction of engineer incharge.

Wall ACOUSTICS Wooden Work And Acoustic Panelling 636Sqft, as per satisfaction of engineer incharge.

SUSPENDED LEANER LED Lights 4Ft, as per satisfaction of engineer incharge.

PHILIPS LED DOWNLIGHTS 15Watt, as per satisfaction of engineer incharge.

Electrical works :- WGSTLPT Point wiring in PVC conduit, with modular type switch. Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. Group A.

LPACCMOD S/F Light plug point modular type accesorries : each supplying and fixing suitable size GI box with modular plae and cover in front on surface and recess , including providing and fixing 3 pin 5/6 amps modular sockets outlet and 5/6 amps modular socket outlet and 5/6 amps modular switch, connecton ,painting etc. as required .(for light plugs to be used in non residentials buildings)

PPACCMOD S/F power plug point modular type accessories : each supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular sockets outlet and 15/16 amps modular switch, connecton, painting etc. as required

WGSTLSB Circuit/ submain wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2x2.5 sq. mm + 1x2.5 sq.mm earth wire.

WGSTLSB Circuit/ submain wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 4 X 6 sq. mm + 2 X 6 sq. mm earth wire.

WGSTLSB Circuit/ submain wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 4x10 sq. mm + 2x10 sq.mm earth wire.

PVCCON S/F PVC conduit: Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25mm.

PTSWEB S/F modular type switch/ socket: Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet.

MODFREB S/F modular type electronic fan regulator: Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

PPACCPT S/F power plug point modular type accessories: Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

CREB S/F ceilling rose: Supplying and fixing 3 pin, 5 amp. ceilling rose on the existing junction box/ wooden block including connection etc. as required.

BRHOLD S/F brass holder: Supplying and flxing brass batten/angle holder including connection etc. as required.

ITCFFSUR ITC fluorescent fitting directly on surface: Installation, testing and commissioning of pre-wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling / wall, including connection with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

ITCCFFC ITC ceiling fan: Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

ITCEF450 ITC exhaust fan upto 450 mm sweep: Installation of exhaust fan upto 450 mm sweep in the existingopening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as required.

LOUSHEF Fixing louvers/shutters for exhaust fan: Extra for fixing louvers/shutters complete with frame for a exhaust fan of all sizes.

PWTPMCBDB S/F prewired TP MCB DB: Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator) 6 way (4 + 18), Double door.

MCBC S/F 'C' Curve, SP MCB Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole.

MCBTPIS S/F TP MCB isolator: Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissoning etc. as required. 63 amps.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. Each

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering.

Supplying and fixing of Decorative LED tube light fitting 18W, 4 feet complete with making connection and complete with all respect directed/approved by E/I.Havells make

S/F of Decorative mirror Linght / LED Batten polycarbonate housing& intregrated electronic driver & making connection complete in all respect. 9W 830 Including GST, Cartage, Labour Charges etc.

S/F of Exhast fan 230/300 mm as approved by E/I complete with making connection---- complete in all respect.Including GST, Cartage, Labour Charges etc.

S/F of singler hight wall breakt / celing light made of brass or as approved by e/I on mataking base complete with making conneti complete in all respect

S/I of Hot water heater (Geyser) 25 Ltr.capacaty as aproved by E/I complete with making conneti complete in all respect

Supply of PVC insulated Aluminium Armoured served XLPE power cable 10 sqmm. 4 core 650/1100 V grade confirming to IS 7098 (Part-1) 1988 complete in all respect.

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc 4 * 1.5 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc 3 * 2.5 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc 3 * 4 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc 2 * 6 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc 4 * 2.5 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc 4 * 4 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc 4 * 6 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc 4 * 10 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc 4 * 16 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc 10 * 2.5 sq.mm control cable

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc 19 * 2.5 sq.mm control cable

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc: 4 * 6 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc: 4 * 10 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc: 4 * 16 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc: 4 * 25 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc: 3.5 * 35 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc: 3.5 * 50 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc: 3.5 * 70 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc: 3.5 * 95 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc: 3.5 * 120 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc: 3.5 * 150 sq.mm

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc: 3.5 * 185 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated using double compression glands and copper lugs: 4 * 1.5 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated using double compression glands and copper lugs: 3 * 2.5 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated using double compression glands and copper lugs: 3 * 4 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated using double compression glands and copper lugs: 2 * 6 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated using double compression glands and copper lugs: 4 * 2.5 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated using double compression glands and copper lugs: 4 * 4 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated using double compression glands and copper lugs: 4 * 6 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated using double compression glands and copper lugs: 4 * 10 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated using double compression glands and copper lugs: 4 * 16 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated using double compression glands and copper lugs: 10*2.5sq.mm Control Cable

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Copper cables , PVC sheathed , armored, PVC insulated using double compression glands and copper lugs: 19*2.5sq.mm Control Cable

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated using double compression glands and Al lugs: 4 * 6 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated using double compression glands and Al lugs: 4 * 10 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated using double compression glands and Al lugs: 4 * 16 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated using double compression glands and Al lugs: 4 * 25 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated using double compression glands and Al lugs: 3.5 * 35 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated using double compression glands and Al lugs: 3.5 * 50 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated using double compression glands and Al lugs: 3.5 * 70 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated using double compression glands and Al lugs: 3.5 * 95 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated using double compression glands and Al lugs: 3.5 * 120 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated using double compression glands and Al lugs: 3.5 * 150 sq.mm

Supplying all materials required for termination and terminating the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated using double compression glands and Al lugs: 3.5 * 185 sq.mm

Supply & installation of overhead cable trays, Including horizontal & vertical bends, reducers, tees, cross members and other accessories as required. This will include all material required for installation including GI suspenders etc. when suspended from ceiling or Angle irons etc. when grouted in wall or as per site conditions and requirements. Width of the cable tray shall be of following sizes:MS CABLE TRAY RICO 30 * 150 * 30 mm

Supply & installation of overhead cable trays, Including horizontal & vertical bends, reducers, tees, cross members and other accessories as required. This will include all material required for installation including GI suspenders etc. when suspended from ceiling or Angle irons etc. when grouted in wall or as per site conditions and requirements. Width of the cable tray shall be of following sizes:MS CABLE TRAY RICO 50 * 300 * 50 mm

Supply & installation of overhead cable trays, Including horizontal & vertical bends, reducers, tees, cross members and other accessories as required. This will include all material required for installation including GI suspenders etc. when suspended from ceiling or Angle irons etc. when grouted in wall or as per site conditions and requirements. Width of the cable tray shall be of following sizes:MS CABLE TRAY RICO 50 * 450 * 50 mm

Supply & installation of overhead cable trays, Including horizontal & vertical bends, reducers, tees, cross members and other accessories as required. This will include all material required for installation including GI suspenders etc. when suspended from ceiling or Angle irons etc. when grouted in wall or as per site conditions and requirements. Width of the cable tray shall be of following sizes:MS CABLE TRAY RICO 50 * 600 * 50 mm

Supply & installation of overhead cable trays, Including horizontal & vertical bends, reducers, tees, cross members and other accessories as required. This will include all material required for installation including GI suspenders etc. when suspended from ceiling or Angle irons etc. when grouted in wall or as per site conditions and requirements. Width of the cable tray shall be of following sizes:MS CABLE TRAY RICO 25 * 50 * 25 mm

Supply & installation of overhead cable trays, Including horizontal & vertical bends, reducers, tees, cross members and other accessories as required. This will include all material required for installation including GI suspenders etc. when suspended from ceiling or Angle irons etc. when grouted in wall or as per site conditions and requirements. Width of the cable tray shall be of following sizes:MS CABLE TRAY RICO 25 * 100 * 25 mm

Supply & Laying of heavy duty hume pipe under the ground for HT/LT cable and of following dia:.200 mm dia

Supply & Laying of heavy duty hume pipe under the ground for HT/LT cable and of following dia:.300 mm dia

50 * 5 mm copper strip in 80 mm GI Class B pipe as required.

50 * 5 mm copper strip as required.

40 * 5 mm copper strip in 50 mm GI Class B pipe as required.

40 * 5 mm copper strip as required.

50 * 5 mm GI strip in 50 mm GI Class B pipe as required.

50 * 6 mm GI strip as required.

25 * 6 mm copper strip in 40 mm GI Class B pipe as required.

25 * 6 mm copper strip as required.

32 * 6 mm GI strip as required.

8 SWG Copper wire as required

8 SWG GI wire as required

16 sq.mm PVC insulated Cu conductor

70 sq.mm PVC insulated Cu conductor

MAIN LT PANEL : fixing, testing & commissioning of Main LT Panel as described below

erection& commissioning of following distribution panels made of 2 mm thick CRCA steel sheets, Floor mounted, fully enclosed, compartmentalized, dust & vermin proof with hinged & lockable doors, & complete with earthing, painting as required and mounted with the following : ( for detail specs refer technical specifications). FLOOR panel

Supply , installation, testing and commissioning of the following rating 1000 KVA outdoor type transformer (oil cooled) as specified, in the Technical specifications, complete with the following standard, mountings, fittings, accessories, etc as required. the Transformer must confirm to IS 1180 standards .

ITC 600 kva ‘Silent’ DG set (CPCB-II Approved) comprising of suitable Engine coupled to Alternator rated at 380 kva, 415 V mounted on a common base frame, complete with: Genset SpecificationGenset Rating (kVAJ* 400 Power Rating (KW 320 No. of Phase 3Output Voltage (V) 415 Power Factor (lagging) 0.8 Current (AJ(1 Phase/3Phase) 556 Frequency [Hz) RPM 50/1500 Governing Class G2 Starting System 24 V DC Electri Fuel Tank Capacity (lit) 700 Genset dimensions 5000 x 1900 x 2303 [Lx Wx H) (mm) approx. Genset Weight (kg) approx. 5200 Engine Specification Make/ Series Perkins Engine Model 2206D-E13TAG3 Power Output # (Kw) 367 453 Aspiration TCA No. of Cylinders 6 Bore x Stroke (mm) 130 X 157 Displacement (lit) 12.5 Fuel Consumption @ 75% 65.5 78.6 load (lit/hr) ^ Fuel Consumption @ 100% 90.5 load [lit/hr) Total lubrication system capacity (|lit) 40 Lube Oil Consumption @ Full Load 0.1% of Fuel Consur Lube Oil Change Period (hrs.) 500 Radiator Coolant Capacity (lit) 51.4 Alternator Specification Make CG/LS/Stamford/Equivalent Enclosure Type IP23 Voltage Regulation +1% Class of Insulation HMaximum Unbalanced Load across Phases 25%

Providing and fixing 6m pole with 70w led light with foundation civil work

Supply, Laying, testing and Commissioning of the following sizes of 1100 V grade Al cables , PVC sheathed , armored, PVC insulated, on existing cable trays/ cable pits/ walls including the cost of saddles, gut ties, clamps, etc: 10 sqmx4 core

Supply, fixing, testing and Commissioning of electrical panel

Supply, fixing, testing and Commissioning of solar system, Modules/Watt 100 KWP Mono PERC HALF CUT DCR (145"550W), Make Inter Solar MNRE specification, Inverter - Sofar 100 KW 3 Phase or 2*50KW Make Sofar-String inverters IEC certified, M.S/G.I Structure for SPV Panels MNRE specification Surge Protection Device Panel (SPD) Suitable Size Make-Inter solar MNRE, uabie Dize Make-Inter solar specification, D.C Wire/Meter 4mm? Polycab/Finolex/ Havells/Inter Solar, 4mm 2 as required at site

SITC of 8 passenger lift with power operated, Elevator Type Passenger elevator PWI08/10-19 Product IMonospace No of Units 1 Load & Capacity 544 kg or 8 persons Speed 1m/s Stops & Openings 3 stops & 3 openings single entrance car Total no of opening 1 emtrances Travel height 9 m Elevator Grouping Simplex - full collective control Well Dimension 1650 mm width and 1650 mm depth (required) Head Room height 3800mm (required) Pit Height 1650mm (required) MAP Floor Position Top most floor (Top) Car dimensions 1100mm wide x 1300mm deep x 2200mm high Door dimensions 700mm wide x 2000mm internal height Door type Two panel centre opening plain panel as per satisfaction of engineer incharge.

SITC of 16 passenger lift with power operated, Elevator Type Passenger elevator PWI08/10-19 Product IMonospace No of Units 1 Load & Capacity 544 kg or 8 persons Speed 1m/s Stops & Openings 3 stops & 3 openings single entrance car Total no of opening 1 emtrances Travel height 9 m Elevator Grouping Simplex - full collective control Well Dimension 1650 mm width and 1650 mm depth (required) Head Room height 3800mm (required) Pit Height 1650mm (required) MAP Floor Position Top most floor (Top) Car dimensions 1100mm wide x 1300mm deep x 2200mm high Door dimensions 700mm wide x 2000mm internal height Door type Two panel centre opening plain panel ,as per satisfaction of engineer incharge.

C.C.TV. 3 MP Dome Camera , ONVIF profile s ,UL , CE , FCC Certified , 1/2.8" CMOS sensor ,3.6 mm fixed focal , Min Illumination :0.01 Lux @ (F1.2, AGC ON), 0.028 Lux @(F2.0, AGC ON), 0 Lux with IR , Shutter Time : 1/5s ~ 1/20,000 s , Video Compression : H.265 / H.264 / MJPEG , frame rate 30 fps @ 2 MP , Inbuilt IR LED , IR distance upto 30 mtrs ,IP 66 , POE .(supply only )

3 MP Bullet Camera , ONVIF profile s ,UL , CE , FCC Certified , 1/2.8" CMOS sensor ,3.6 mm fixed focal , Min Illumination :0.05 Lux @ (F1.2, AGC ON), 0 Lux with IR , Shutter Time : 1/5s ~ 1/20,000 s , Video Compression : H.265 , H.264 , frame rate 30 fps @ 2MP , Inbuilt IR LED , IR distance upto 30 mtrs ,IP 66 , POE .

3 MP Dome Camera , ONVIF profile s ,UL , CE , FCC Certified , 1/2.8" CMOS sensor ,2.8mm to 12 mm motorized varifocal , Min Illumination :0.05 Lux @ (F1.2,AGC ON), 0 lux with IR , Shutter Time : 1/5s ~ 1/20,000 s , auto switch IR cut filter ,Video Compression : H.265 , H.264 ,frame rate 30 fps @ 2MP , Inbuilt IR LED , IR distance upto 30 mtrs ,IP 66 , POE .

3 MP Bullet Camera , ONVIF profile s ,UL , CE , FCC Certified , 1/2.8" CMOS sensor ,2.8mm to 12 mm varifocal , Min Illumination :0.01Lux @ (F1.2, AGC ON), 0.001 Lux @ (F1.2, AGC ON), 0 Lux with IR , Shutter Time : 1/5s ~ 1/20,000 s ,Audio 1 Input / 1 output , SD Card Support , Video Compression :H.265 , H.264 ,frame rate 30 fps @ 3MP , Inbuilt IR LED , IR distance upto 60 mtrs ,IP 66 , POE .

4 MP PTZ Camera , UL,CE,FCC Certified , ONVIF profile s , triple stream or more,4.3 to 129mm focal length , 30 X Optical Zoom , 10 X digital Zoom ,Frame rate : 25 fps @ 3MP ,Shutter Speed : 1/3 - 1/10,000 s inbuilt IR LED for night vision ,triple stream or more, IR distance upto 100 mtr or more , 2D / 3D noise reduction ,120 dB WDR , 360 deg endess pan , tilt -15 to 90 deg , auto flip support ,256 presets ,Auto pan ,SD Card support , Auto white balance, Auto iris , 1 X BNC , Alarm : 2 IN , 1 Out , IP 66 weather proof , Power : 24V AC/ POE+ / POE.

ONVIF profile s ,UL certified 2U Rack Mountable 32 Channel NVR , 8 SATA ports , each SATA capacity of upto 8 TB , Recording Bandwidth 320 Mbps , e-SATA Support , 1 X HDMI , 1 X VGA , Alarm : 16ch in / 4ch out , 1 X RJ45 port ( 1 GPBS) , 1x3.0 USB for backup / upgrade, 2x 2.0 USB for mouse , Smart Phone support : iOS, Android

8 TB Surveillance Hard Disk Drive

Supply & Laying Of Cat-6 Cable Compliant to TIA / EIA 568-C.2 & ISO/IEC A1801 Class E , AWG 23 , Operating Temperature 0° C to 70° C , Insulation Resistance 500 MὨ minimum , low smock zero halogen (LSZH)with idetification and numbring on cable on both ends

Supply, laying & testing of 6 Core INDOOR FIBER OM3 MM cable. OM3 low smock zero halogen (LSZH)

Supplying and installation of wall mounted 19'' minimum 6U Rack with glass front door, steel rear door, PDU with MCB 6 socket , cable manager, Cooling Fan Tray 4 Fans, drawer shelves and wiring channels to accommodate CCTV systems equipment and accessories as mentioned in the BOQ above and including all connections and terminations as required

Supply, installation, testing and commissioning of 24 port Cat 6 Patch panel Fully loded duct assembly, screws, washers and an instruction sheet for termination of incoming pairs.

24 x 10/100/1000BaseT PoE+ (RJ-45) ports 4 x 100/1000BASE-X (SFP) unpopulated ports 15 Watt per PoE port ( 7 install +2 supply only)

24-port Gigabit Managed SFP+ Switch

Cat-6 Patch Cord 2 Mtr LSZH CMR ( 100 install + 60 supply)

SC to LC Multimode Duplex Fiber Optic Patch Cable

Gigabit SX Mini-GBIC Multimode SFP Transceiver

Moduler plug terminated link (MTPL) direct connect solution for cctv and wifi through RJ45 Plug with 25 years warreny & 100 watt PoE certified

PVC conduit with required accessories like Screws,Glanding,Clamping,Trays etc. Make:

P/FIXING FLEXIBLE PIPE

LISHA ENGINEERS PRIVATE LIMITED

KBPL INFRASTRCUTURE PVT.LTD.