CA NO CWE / HILLS / EWS/70 OF 2020-2021 CONSTRUCTION OF TRAINING SHED AT JOSHIMATH UNDER GE 871 EWS

Amount

Excavating in trenchs, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and getting out in hard/ dense soil complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exc. 25 cm. complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for hard core of broken stone or boulders of gauge not exc 63mm deposited, spread & levelled in layers not exc 15cm thick, including watering and ramming to a true surface complete all as specified and directed.

M&L for pre construction anti termite treatment of the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for pre construction anti termite treatment of the soil alongwith external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

M&L for Cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregates) as in foundations filling and mass concrete complete all as specifed and directed.

M&L for 75 mm thick PCC 1:3:6, type C-1 (using 20mm graded stone aggregates) as in plinth protection complete all as specified and directed.

M&L for 50mm thick PCC 1 :2:4 type B-0 (using 12.5mm graded stone aggregates) as in damp proof course to horizontal or vertical surfaces including necessary form work complete all as specified and directed.

M&L for RCC (design mix) M-25 as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc, basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L for RCC (design mix) M-25 as in beams, cantilevers, bressumers, lintels over 1.5m span complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to better flat and rough finished surfaces of concrete complete all as specified and directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns, and stanchions square, rectangular or polygonal and rough finished surfaces of concrete complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape requred, including cranking, binding spirally for hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars in reinforcement 5mm dia and over up to 10mm dia in stirups cut to length bent to shape required including cranking binding spirally, hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.

M&L for walling of random rubble masonry un coursed, well bonded and solidly hearted built in CM 1:6 complete all as specified and directed.

M&L for precast cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in solid building blocks, exc. 10cm in width and setting in CM 1:6 complete all as specified and directed.

M&L for 40 mm thick cement concrete 1:2:4, type B-1 (Using 20 mm graded stone aggregate) as in floor, finishing cement concrete surface even and smooth with out using extra cement complete all as specified and directed.

M & L for 15 mm thick rendering in two layers on fair faces of brick work or concrete surfaces first layers 10 mm thick with cement mortar 1:6 and second layers 5 mm thick with cement mortar 1:4, finished even and smooth without using extra cement complete all as specified and directed.

S&F pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

S&F anodised aluminum frame for doors, windows, partition wall, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F for anodised aluminium door shutters, aluminium section weighting not less than 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc complete all as specified and directed.

M&L for 12 mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination, fixed with screws to timber/aluminium frame work complete all as specified and directed.

S&F for steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specifed and directed.

S&F for 0.63mm Galvanised mild steel wire cloth, nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S&F for 4 mm thick sheet glass ordinary qauality and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and directed.

S&F for 200 mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F for 150 mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F for 150mm anodised extruded aluminium alloy handles, fabricated type complete all as specified and directed.

S&F for 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 100 mm long, butt hinges medium weight cold rolled complete all as specified and directed

S&F for 150mm length floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specifed and directed.

S&F for door closer aluminium (die cast) body hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified and directed.

S&F for brass mortice lock (4 lever), vertical type of size 100 mm complete all as specifed and directed.

M&L for preparation of new steel surfaces any description, over 10cm in width or girth,not otherwise applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F for 15mm thick unique sports Interlocking PP Tiles of including all material, labour and T&P etc as in all floors complete all as specified and directed.

M&L for point wiring for one light/fan/bell point controlled by one ,one way switch in PVC conceled of required size confirming to IS 2079-1973 medium grade on surface with PVC insulated unsheathed multistranded copper conductor cable (FR) 1.5 sqmm nominal cross sectional area 1100 volts grade complete with all fittings such as Elbow, bends, junction boxes, saddles incl PVC board (ISI Mark) and screws and rawalplug etc including 1.5 sqmm PVC insulated & unsheathed copper conductor cable as earth wire and connected to light/fan & common earth dolly with necessary copper thimbels all as specified and directed.

All as per item No 41 above but one socket outlet 5 pin 5/6 Amps on same board with other one, one way modular switch.

All as per item No 41 above but for socket out let modular type, 15/16 Amps on independent board with 4 Sqmm size cable and 2.5 Sqmm for continuty earth wire connected to common earth dolly complete all as specified and directed.

S&F 15/16 Amps, modular switch, single pole, one way complete all as specified and directed.

S&F 5/6 Amps, modular switch, single pole, one way complete all as specified and directed.

S&F modular socket out let, 5 pin, 5/6 Amps complete all as specified and directed.

S&F modular socket out let, 5 pin, 15/16 Amps complete all as specified and directed.

S&F modular white cover with frame, 4 module suitable for 15 Amps switch socket complete all as specified and directed.

S&F modular white cover with frame, 12 module suitable for 5 Amps switch socket complete all as specified and directed.

M&L for ceiling rose 2/3 terminals 65x25 mm dia poly carbonate isolated complete all as specified and directed.

S&F lamp holder, PVC/ polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F 9 Watt LED bulb cool day light, 230/240V AC supply complete all as specified and directed.

S&F LED tube light fitting bright 18 watt, slim elegant design and including connected with 3 core 23/0.0076 insulated copper wire from ceiling rose to fittting connector complete all as specified and directed.

S&F security light fitting complete with 25 watt LED type pressure die cast aluminium housing and heat resistant toughned glass with frame protection and better optics for uniform distribution etc complete fixed bracket made out by GI pipe (light grade) of suitable size and MS clamp and nut bolts washers etc complete and connected with twin core cable 1.5 sqmm from ceiling rose to fitting connector all as specified and directed.

S&F sheet metal enclosure for MCB's distribution board TPN double door 4 way 415 V, incoming and outgoing MCBs double pole/ single pole complete all as specified and directed.

S&F 6 to 32 Amps MCB, single pole with thermal over load as well as magnetic short circuit tripping device with quick, break trip free mechanism, robust design and terminals having heat resistance moulding suitable for single phase circuit complete all as specified and directed.

S&F 100 Amps MCB, TPN with thermal over load as well as magnetic short circuit tripping device with quick, break trip free mechanism, robust design and terminals having heat resistance moulding suitable for single phase circuit complete all as specified and directed.

S&F 32/40 Amps MCB, DP with thermal over load as well as magnetic short circuit tripping device with quick, break trip free mechanism, robust design and terminals having heat resistance moulding suitable for single phase circuit complete all as specified and directed.

S&F heavy duty, exhaust fan, 450 mm sweep, metal body, sound proof with louver shutters of 750 RPM complete all as specified and directed.

M&L for sub main wiring in PVC casing and caping of required size, 2 x 6.0 Sqmm PVC insulated multistrand copper conductor with 01x 4 Sqmm PVC insulated multistrand copper conductor as earth continuity wire complete all as specified and directed.

M&L for earthing complete with galvanished steel earth plate electrode size 600X600X6mm thick burried directly in ground vertically to a depth not less than 2.25m below normal ground level with top edge of earth plate not less than 1.5m below normal ground level connected to and incl GI earth lead wire 4mm dia by means of bolts ,nuts, check nuts & washers of galvanised iron and connected to test point all as shown in electrical plate No 3 of SSR part I-2009 and as specified or indicated and testing on completion incl excavation and earth work in any type of strata available at site ,PCC (1:3:6)type C-1 earthing chamber ,pre cast RCC slab 50 mm thick in cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate reinforced with welded steel wire fabric (XPM) weight not less than 4 kg/sqm funnel with GI watering pipe of 20 mm bore medium grade ,wire mesh and lugs ,GI protection pipe of 15 mm bore light grade up to 7.5 mtr long ,etc complete all as specified and directed.

S&F 30 watt, flood light for hanger complete all as specified and directed.

S&F of aluminium strip 25 x 3.15mm with saddles and fixing screws, insulators rawal plugs etc for conductor for roof and fixed on wall upto test point complete all as specified and directed.

S&F of wooden block heavy weight of size 30x30x30 cm with hole of 20 cm for fixing of air termination rod of any size including dismantling and taking down old existing unserviceable wooden block complete all as specified and directed.

S&F of GI tubes light grade, galvanised, 20mm bore including necessary GI fittings, laid in trenches or under floor or fixed with poles/walls for fixing of air termination including dismantling and taking down old existing unserviceable GI tubes light grade complete all as specified and directed.

S&F of five pointed air termination aluminium rod 12mm dia, 300 mm long complete all as specified and directed.

S&F test point terminal block made of gun metal or phosphorous bronge 75 x 75 x 25mm of 6mm thickness drilled and screwed including 3 Nos, 8mm dia, 25mm long hexagonal head brass screws including box of size 90 x 90 x 90mm made of 1.6mm plain sheet and screwed to wall for protection of test point complete all as specified and directed.

M&L for earthing complete with GI earth plate electrode 60x60cmx6mm thick burried directly in ground in earth pit not less than 2.25 mtr depth below normal ground level with top edge of the plate vertically to depth of not less than 1.5 mtr below ground level connected to & including 32 x 6 mm as earthing strip connecting to equipment by means of GI bolts & nuts etc with provision of charcoal and salt etc all as per electrical plate No-3 of SSR part-I 2009 including RCC cover and MS angle iron frame, watering with GI pipe 20 mm dia (medium grade) & MS funnel, concrete pit including excavation and earthwork in any strata and testing on completion etc. complete all as specified and directed including all excavation, concreting, refilling and removal of material.

M&L for sand cushioning for protection of PVC cable with approved sand of uniform thickness, laid dry, by filling in trenches and punning to proper required cover complete all as specified and directed.

M&L for old size brick sub class 'B' for protection of cable complete all as specified and directed.

M&L for 40 mm dia steel tubes (light grade) galvanised with fittings, laid in trenches/wall/pole for protection of underground cable when crossing the road/fixing complete all as specified and directed.

Supply and lay in trenches, fixed to wall/pole UG cable XLPE insulated screened PVC beded galvanised steel strip or wire armed heavy duty electric cable with multi stranded aluminium conductor, 1100V grade of size 35 sqmm 3.5 core complete all as specified and directed.

airstack india

RAKESH CHANDRA PANT