SPL REPAIR TO BLDG NO T14 OF 4 DOGRA P14 TOILET OF 61 RR BN JAT T96 OF 899 AT COY PROVN OF DRAINAGE NEAR BLDG NO T53 T84 PROVN OF PATH DRAINAGE PROTECTIVE WK NEAR BLDG NO T04 OF STN HQ AND SPL REPAIR OF ELECTRICAL WIRING TO BLDG NO T88 T89 OF INF

Amount

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust all as specified.

M&L for rendering 15mm thick cement plaster with cement mortar(1:4) on fair finishes of brick work or concrete surface of roof slab all as specified.

Roof treatment : Water proofing treatment to RCC roof slab including of parapet as under:- (a) First Course : Apply a coat of biruminous primer conforming to IS - 3384 @ 0.40 Kg/Sqm on prepardd surfaces of plaster and After drying of primer apply a coat of hot blown 85/25 penetration grade blown bitumen conforming to (IS-702 @ 1.20 Kg/Sqm on plasterd surfaces. (b) 2nd Course : APP(Atactic Polypropylene) modified polymeric 5 layed 3 mm thick weight not less than 4.0 kg/Sqm with 160 Grams/Sqm non woven polyster made at centre core reinforced laid with 75mm side overlap and 150mm end overlap, membrane has to be laid with LPG torch and overlap sealed and finished neat, all joints and changes in direction should be covered with cement mortar 1:3 mixed with SBR latex @200ml/bag of cement and curved before laying of membrane. (c) 3rd Course: Apply a coat of ht blown 85/25 grade bitumen conforming to IS-702@ 1.20 Kg/sqm over membrane and dusted with dry sand @ 0.50 to 1 Kg/sqm. Note:- Roof treatment work shall be carried out through approved manufacture only (ii) If non accesible roof after providing (a) to (c) provide two coat of aluminium paint as per manufacture instructions (iii) Covered filled in PCC 1:2:4 type B0 using 12.5 graded crushed stone aggregate of required radius shall be provided at the junction of roof and vertical surface such as parapet wall/mumty around opening and treatment mentioned above shall be applied followed by a cement plaster 20mm thick in cement mortar (1:6)

Taking down cement plaster on brick or stone wall, including raking out joints, hacking for key scrubbing down with water etc.

Rendering 15 mm thick on other than fair faces of brick/concrete or stone masonary surfaces in CM 1:6 finished even & smooth without using extra cement

M&L for rendering 5mm thick cement plaster with cement mortar(1:3) on concrete surface as in ceiling finished even and smooth without using extra cement complete all as specified and directed

M&L for rendering 10 mm thick cement plaster with cement mortar(1:6)on other than fair faces of brick work or concrete surfaces and finished even and smooth without using extra cement.

M&L for GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste.

M & L Preparing new surfaces of walls and applying two coats of distemper oil emulsion over one coat of chalk whiting.

M&L for preparing of new plasterd surfaces of ceiling and apply two coats of white wash on ceilling.

M&L for preparation of new surfaces and apply two coats of cement based paint including primer complete all as specified and directed by Engineer -in-Charge. Make: Super Snowcem/Duracem/Berger

S &F Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete. Make : Sintex/Polycon/Rotex or Equivalent.

M&L for Mild steel galvanized steel tubing medium grade 20mm bore with all fittings and fixed complete to walls and ceiling or laid in floors complete including taking down of old pipe.

Mild steel galvanized steel tubing medium grade 15mm bore with all fittings and fixed complete to walls and ceiling or laid in floors complete including taking down of old pipe.

S&F in repairs stop valves cast copper alloy serwed down high pressure , 15 dia bore fixed.

S&F ball valve high pressure PTMT with epoxy coated aluminium rod & high density plastic ball 20mm dia bore.

Demolition of cement concrete any description and in any postion not otherwise all as specified & directed

Providing cement concrete type C-1, 1:3:6 ( using 20mm graded stone aggregate), 50 mm thick as in plinth protection laid in bays not exceeding 2 Sqm each and finishing even and fair on top without using extra cement with 6mm wide joints throughout the thickness of plinth protection in concrete bays and in between the walling and plinth protection, filling the joints with mastic filling comprising of one part of heated bitumen 85/25 or 95/10 grade and 3 parts of sand ( all by weight).

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 sqm, in floors etc /set and jointed in neat cement slurry and pointed in coloured cement to match including 15 mm thick screed bed in cement and sand mortar 1:4, complete all as specified and directed. Make : Kajaria/Somany/Orient Bell.

M&L Glazed ceramic tile 300 x 200 x 06-07mm thick (coloured) on vertical surfaces such as dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10 mm thick screed bed in cement and sand mortar 1:4, complete all as specified and directed. Make : Kajaria/Somany/Orient Bell.

Taking down chowkhat or frames of door/ window with shutters (Without taking off shutter from the frame) exc 1.00 m and n.exc 2.00 Sqm each.

Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia thresh old bar and filling hollow of frame of sizes of frame :-105x60mm.

PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate as in filling of pressed steel frame.and including 50 mm parapet coping all as specified etc.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top and bottom rails. M.S frame shall be covered with heat channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as a gap insert for top rail and bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S frame welded / sealed to the stiles and nails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at side as per specification and drawings. Make : Polycon/ Rajshri/Sintex or Equivalent

Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S square tube, supplying and fixing in opening as per specification and drawing. Make : Polycon/ Rajshri/Sintex or Equivalent

S & F Steel window/ventilator (Box type) factory made with double shutter (wire gauged shutter and glass/glazzed shutter including MS tower bolt 02 Nos each, wire cloth and glass paned shall be measured and paid separately of size 79mm x 39 mm, 16 guage rectangular tubular frame with side hung. fixed in repairs complete all as specified and directed. Make : A/S Sanjay Steel Works, Jammu or M/S Steelmen Industries Jalandhar. CEUZ/TD/1269/2008 Sheet 1/1 to 1/3.

S&F figured glass sheet, 4mm thick, ordinary quality and glazing with oil putty and glazing pins in squares not exceeding 0.5 Sqm in each pane.

S&F 100 mm butt hinges, meium weight cold rolled mild steel.

S&F Aluminium handles cast type anodised of size 150mm long ISI marked complete.

S&F Aluminium anodised barrel tower bolt 200 mm, extruded section.

S& F aluminium anodised sliding door bolts round nuckle with hasp and stapple extruded section or cast aluminium alloy 300 mm long complete all as specified.

S&F stop valves cast copper alloy serwed down high pressure with crutch or butterfly handle 20mm dia bore fixed in repairs.

M&L for PVC (Plastic polymer Cistern) valve less, Symphonic action type, flushing cistern of capacity 10 liters, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete, fixed in repairs.

S&F vitreous china squtting pan "Orissa Pattern" size 580 x 440 mm in any coloured with integral foot rest incl lime motor, 'S' trap and complete all as specified, fixed in repairs.including taking down all as specified.

S&F PVC connection 15 mm size with PTMT nuts 450 mm long.

S&F Aluminium anodised towel rail 20mm dia 'D' type 60 cm long between flanges .

S& F liquid soap container of PTMT fixed with and including chroumium plated brass screws and wooden/plastic cleats (mm weight 105gms) fixed in repairs complete all as specified and directed.

S&F CP Bib taps, cast copper alloy, fency type ISI marked with wall flange for iron pipe of 15 mm bore and if fixed in repairs complete all as specified and directed.

S&F CP Angle valve/concealed stop cock of cast copper alloy (ISI Marked) chromium plated facny type screwed down high pressure with capstain head screwed both ends for iron pipe of 15mm bore incl add if fixed in repairs complete all as specified and directed.

S&F vitreous china wash basin (white) flat back size 580x450 mm including all fitting accessories CP, waste coupling and PVC wate pipe fixed in repairs all as specified and directed.

S & F in repairs chromium plated fancy type pillar tap with lift type operating knob and base flange, 15mm bore dia all as specified and as directed.

Cast iron floor trap 75 mm dia, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified.

Salt glazed stoneware gully trap square or round mouthed type 'P' of size 150x150 complete all as specified.

M&L for providing pre-cast RCC 1:2:4 type B1 using 20 mm graded stone aggregate as in cover (for manholes and drains) including necessary form work set in CM 1:4 with and including demolition complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately).

S&F MS TMT bars 10 mm dia and above cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Demolition of brick work built in cement or cement lime mortar incl all quoins, arches, pillars etc, complete all as specified & directed.

M&L for brick work with sub class ‘B’ brick, straight curved on plan exc 6m mean radius built in cm (1:4) using old size bricks complete all as specified and directed.

M&L for providing PCC 1:2:4 type B1 using 20 mm graded stone aggregate as in coping, bands, plinth course, benching and other similar works including use and wast of necessary form work complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately).

Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete) set in cement mortar including concrete bedding and haunching complete all as specified and directed for 150mm bore of pipe.

M&L PCC 1:4:8 type D-2, using 40mm graded stone aggregate as in bed of drain pipe including packing under and haunching against the sides of pipes after they are laid and tested for the 150mm dia of pipe complete all as specified and directed.

Salt glazed stoneware (SGSW) grade 'A' drain pipes 150mm bore laid and jointed on concrete bed, complete including testing etc. all as specified.

S& F Cast iron cowls including stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof.

Cleaning and desludging of existing septic tanks / sump well/ deep man holes of up to 3 metre deep including taking out sludge in any form alongwith all other foreign materials by mechanical equipment or manually or by way of any other suitable means including removal of sludge and other foreign materials out side the MD land by any means complete (working in foul condition) all as specified & directed.

S&F Connecting pieces 100 mm dia one end flanged and other socket or spigot and bell mouth pieces one end flanged other end tapering as bell mouth all as specified and directed.

S & F cast iron 100 mm dia Single junctions laid and jointed, complete all as specified and directed.

S & F cast iron100 mm Bends (any radius) with duck's foot or heel rest all as specified and directed.

S & F 50 mm Cast iron pipes with flanged ends/ verticaliy cast, Class A, in any length, laid in trenches all as specified and directed.

M&L for 75mm thick PCC type C-2, 1:3:6 using (40mm graded aggregate) as in sub base.

M&L for screed bed in CM (1:6), 20 mm thick in floor.

M&L chequerred cement concrete tile with grey cement and pigment 30 cm x30cm x25mm thick set and jointed and pointed in neat cement slurry in floor all as specified.

M&L for excavating over area, n.exc 1.5m deep and getting out in any type of soil complete all as specified and directed.

M&L for cement concrete in foundation filling and mass concrete type D2 1:4:8 (using 40mm graded Agg) all as specified and directed.

M&L for walling of random rubble stone masonay, uncoursed, well bounded bedded and solid hearted, built in CM (1:6) all as specified.

M&L for raised pointing to random or polygonal rubble, uncoursed or brought upto courses in cement 1:4 all as specified.

M&L for precast cement concrete 1:2:4 B-1 using 20mm graded crushed stone agg) as in bounders for stone walling and similar articles with plain faces, and set in cm 1:6 all as specified.

M&L for extra overs stone walling for hammer dressing to faces stone and dressing of face beds and joints as specified of random rubble walling , uncoursed or brought upto course, hammer dressing with maximum depression on face from straight edge held against the dressed surface and exceeding 40 mm for lime or sand stone, all as specified.

S&F PVR SWR pipe (75mm dia) single socketed in any length with rubber ring joints,for weep holes

M&L for returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soil.

M&L for removing excavated material n exc 50 mtr and depoositing where directed at a level n exc 1.5 mtr above the starting point in soils.

Excavation in trenches in any type of soil n.exc 1.5m wide and n.exc 1.5m in depth and getting out.

M&L for old size brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6

M&L Rendering 10 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement incl forms, moulds mitred/stopped ends etc.

M&L for surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in any type of soil.

M&L for hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface.

M&L chequerred cement concrete tile with grey cement and pigment 20 cm x20cm x25mm thick set and jointed and pointed in neat cement slurry in floor all as specified.

Soakage wells excavation,in any tpye of soil,foundation in PCC 1:3:6,walls of honey combed masonry with top ring of M-25 concrete including intercepting chamber and screen chamber made of brick masonry in CM,RCC cover slab in M25/SFRC cover,interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.8m x 4.5m effective depth.

M&L for cement concrete (1:3:6) type C-2, using 20mm graded stone aggregate bed to drain pipe 150mm dia including packing under and completely surrounding the pipe with concrete after they are laid and tested including necessary formwork all as specified.

S&F PVC(SWR)bends of 75mm bore

S&F PVC(SWR) pipes double socketed,in any length with rubber ribg joints,laid in trenches of 110 mm bore

S&F reinforced concrete pipes,class NP2,laid and jointed complete with collars of bore 150mm

M&L plain cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate cast in citu as in coping /benching including necessary formwork all as specified.

M&L for precast reinforcement cement concret 1:2:4, type B1, using 20mm graded stone aggregated as in cover slab for manholes septic tank etc all as specified and directed by Engr -in- Charge.

Cutting in to existing manholes for connecting new drains pipe internal dia 150mm and making good to pipe and rendering, cutting out existing benching for and forming branch channel(1/2 round or 3/4 sec) in cement concrete 1:2:4 type B1, smooth finished,and reforming benching as required all as specified and directed by Engr -in- Charge.

M&L for mild steel TMT bars 6 to 8mm dia cut to length, bent to shape required including cranking bending and binding with and including mild steel (annealed) wire not less than 0.9mm dia as in stirrups complete all as specified and directed by Engr -in- Charge.

M&L for rendering 15mm thick on fair faces of brick/stone or concrete surfaces in CM 1:4 finishing even and smooth without using extra cement including mixing water proofing compound @ 3%by weight of cement, all as specified. (Note : Water proofing compound shall be measured and paid separately).

Supply only integral water proofing compound.

M&L coloured Chequered cement tiles 20cmx20cmx25mm thick' set and jointed and pointed in cement slurry in floor over 15mm thick screed bed in CM motar 1:6.

Formwork to for fair finished surfaces of walls, retaining walls, abutments, parapets and staircase railing and similar work including attached pillasters, buttresses, etc.; vertical or to better all as speciified and directed.

Reinforcement cement concrete M-25(Design Mix) in Walls, retaining walls, basement walls and the like; any thickness; above top of footings; including attached pilasters and buttresses all as specified.

Reinforced cement concrete M-25 (design mix) using 20mm graded crushed stone aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L for dismantling wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fille complete.

M&L for dismantling carefully of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness including cover fillets GI framework complete and fixed in same position repair all as specified and directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering.

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.with Hangers 6 mm dia. G.I. (upto1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws all as spd by engr in charge.

M&L for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws incl ridge all as specified and directed by Engr-in-Charge.

M&L for pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ ridge, fixed with self tapping screws incl ridge all as specified and directed by Engr-in-Charge.

Rolled mild steel section as in main and cross beams, hip and jack,rafters, purlins, where connected to common, rafters and running rails and guiders for sliding doors: fixed with angle cleats or other connecting plates conforming to grade Fe410-W (Gde E-250) quality 'A' all as specified

Taking down chowkhat or frames of door/ window / ventilators with shutter(Without taking off shutter from the frame) n.exc 1.50 sqm each.

Taking down chowkhat or frames of door/ window with shutters (Without taking off shutter from the frame) exc 1.50 m and n.exc 4.00 Sqm each.

25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in sub floor under tiles, all as specified and directed.

M&L for screed bed in CM (1:6), 15 mm thick in floor.

M&L vitrified ceramic any shade coloured tiles 10 mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match.

Ditto as per item Srl No 106 above but on vertical surface such as skirting, dado and riser to steps etc over complete all as specified.

M&L Rendering 10mm thick in CM 1:3 on brick/stone masonary wall surfaces, other than fair faces of brick work finished even and fair to receive tiles.

S & F 35mm thick Flush shutters, solid core with particle board exterior grade as per IS-2202 of 199 (Part-I). Flush door shutter shall be internally lipped as per clause 8.52.2 of SSR-2009 Part-I complete all as specified and directed by Engr-in-Charge.

S&F Galvanised steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed in repairs.

S&F Glazing with sheet, 4mm thick, ordinary quality and glazing with oil putty and glazing pins in squares not exceeding 0.5 Sqm in each pane.

M&L for complete removal of existing old treatment and apply one coat of oil bound distemper to walls.

M&L for preparation of old treated surfaces and apply one coat of cement base paint to walls.

M&L for preparation of new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide premier.

M&L for preparation of old steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and painting with one coat of synthetic enamel paint.

Dismantling of Wall panelling and similar work all as specified and directed.

S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe). (including flushing cistern & flush pipe) complete in all respect all as specified.

M&L for marble tile makrana Doogri Adanga Marble tiles 20mm thick machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing typeswith edges rounded off white cement sturry including cutting & polishing complete all as directed.

S&F PVC wall lining/panelling consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame including 5mm thick PVC sheet filet of width 35mm to make PVC frame as per manufacturers and drawings complete all as directed.

Machine cut kota stone slab flooring 18-20mm thick size 500 x 500 mm over 20 mm cement screed in CM 1:3 base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

Machine cut kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid over screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete, all as specified.

Marble work 16 to 18mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms and like in 20 mm thick screed bed cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types (screed bed shall be measured separately.

M& L Galvanised steel powder coated snap grid frame work of size 605x605 mm for false ceiling with 600x600x4mm fibre cement board alongwith applying three coats of white wash on board incl necessary notching and preparing holes porting hangers comprise of GI wire for securing frame work to ceiling and snap grid including taking down of existing old/broken false ceiling all as specified by Engr in charge.

M & L Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia thresh old bar and filling hollow of frame of sizes of frame :-125X60mm.

S & F Factory made Plain framed second class hard wood panelled shutter (Two panel), 35 mm thick with lock rail and panel of 12 thick veneered particle board with commercial veneering on both face. The size of rail and style as per IS-1003 (Part-I), Kiln seasoned and chemically pressure treated.

S&F Glazed and skelton shutters 35 mm thick second class hard wood, opened rebated and prepared to receive wire mesh etc, edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for sucuring witre mesh etc. Size of members of shutters as specified in SSR Part-I, Sec-8, clause 8.24(a).

Mild steel springs for doors, 150 mm, ordinary rat tail rod pattern springs including roller and roller plate complete.

S&F Floor door stopper 140mm overall length of cover plate of aluminium alloy body and tongue,nodised,with hard drawn steel spring,fixed in bottom body of door complete all as specified and directed.

M&L for preparation of new untreated wood and wood based surfaces of any description, not otherwise described over 10cm width or girth and painting with two coats of synthetic enamel paint over a coat of pink primer.

S&F curtain rail ,20 mm dia anodised aluminium alloy ,cromium plated fixed with bracket, phenyl corner etc including taking down of old rods , all as specified.

M&L for 60 mm thick machine presed coloured glazed precast interlocking paver block any shape and size with grey cement and pigment (glazed) confirming to IS-15658-2006 over including 25 mm thick sand cushion complete all as specified.

Dismantling plain or corrugated AC sheeting, any guage, thickness, roof covering

Providing cement concrete Type B-1, 1:2:4 (20mm graded aggregate in lintels upto 1..5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directing

Taking down carefully aluminium/copper point wiring (light, fan, bell, socket or power) complete, including fixtures and fitting such as switches, ceiling roses, holders, regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty and white cement at necessary holes for smooth finishing complete all as specified and removing from site.

Material and labour for point wiring complete with 1.5 sqmm PVC insulated, FRLS type, ISI marked,conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables drawn through PVC Conduit 20 mm dia medium grade including cutting, chasing work at any height and all accessories are concealed in walls / roofs / floors / ceiling etc. metal flush box with top,bottom,side/back wall knockout for conduit entry from any direction made out of 1.60mm thick suitable for fixing of modular top cover plate as per numbers of switch modules for modular switches,sockets,fan regulators,red colour indicator, blank plates etc as approved coloures including 1.5 Sqmm PVC insulated multistranded FRLS type unsheathed(Green colour),single core cable with copper conductor cable as earth continuity conductor and connecting to common earth dolly including making good the disturbed surfaces to match with existing surface and colour coat including providing putty and white cement for smooth finishing of existing surface complete all as specified and directed for the following:- (a) One light point/fan /bell point controlled by one switch. Make of Cables: Havells, KEI, Anchor (Note:- All necessary accessories such as modular steel box,top cover plate, blank plate, screws,washers and all modular electrical fixtures are to be used of same make/brand only and shall be deemed in to included in quoted rate only.)

All as per item no 135 above but for One 5 pin 6 amps socket point controlled by one 6 amps switch on independent board .

All as per item no 135 above but for One 5 pin 6 amps socket point controlled by one 6 amps switch on same board .

Material and labour for point wiring complete with 2.5 sqmm PVC insulated, FRLS type, ISI marked,conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables drawn through PVC Conduit 20 mm dia medium grade including cutting, chasing work at any height and all accessories are concealed in walls/roofs/floors / ceiling etc. metal flush box with top,bottom,side /back wall knockout for conduit entry from any direction made out of 1.60mm thick suitable for fixing of modular top cover plate as per numbers of switch modules for modular switches,sockets,fan regulators,red colour indicator, blank plates etc as approved coloures including 2.5 Sqmm PVC insulated multistranded FRLS type unsheathed(Green colour), single core cable with copper conductor cable as earth continuity conductor and connecting to common earth dolly including making good the disturbed surfaces to match with existing surface and colour coat including providing putty and white cement for smooth finishing of existing surface complete all as specified and directed for the following:-(a) One 15 amps power socket outlet point controlled by one 16 amps switch on independent board. Make of Cables Havells,KEI, Anchor Note All necessary accessories such as modular steel box,top cover plate, blank plate, screws,washers and all modular electrical fixtures are to be used of same make/brand only and shall be deemed in to included in quoted rate only.)

Supply & fixing modular type switch 6 Amps, single pole, 1way,1 module,240V, ISI Marked complete all as specified and directed. Make Indoasian Glint, Crabtree, Havells REO

Supply & fixing modular type switch 16 Amps, single pole,1 way,1 module, 240V, ISI Marked Complete all as specified and directed. Make Indoasian Glint, Crabtree, Anchor

Supply & fixing modular type socket shuttered type 6 Amps- 2/3 Pin combined 2 module, 240V, AC ISI Marked Complete all as specified and directed. Make Indoasian Glint, Crabtree, Anchor

Supply & fixing modular type socket 6 A/16 Amps -2/3 Pin combined shuttered socket 2 module 240V AC ISI Marked Complete all as specified and directed Make Indoasian Glint, Crabtree, Anchor

Supply & fix fan regulator modular type electronic, stepped type 100 Watts, 2 module 240Volts, AC ISI marked complete all as specified and directed. Make Indoasian Glint, Crabtree, Anchor

S&F in replacement Lamp holder, insulated body, PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified & directed.

S&F Energy saving LED lamps 7 Watts, 230 volts, 50 HZ, 0.95 PF. complete all as specified and directed. Make: Havells Cat Part No. LHLDERHEMD8X007 or equivalent in Philips/ Crompton/ Bajaj

S&F Energy saving 1x9W/ 1x10W LED bulk head luminaires, IP-65, oval shape, surface mounted with all other accessories prewired and making connections with copper flexible twisted twin cord of appropriate gauge and length, 230v, 50Hz complete all as specified & directed. Make. Havells, Cat Part No. RUGBYNEONFT10WLED760SSYMBOPC or equivalent in Philips/ Crompton/ Bajaj

S&F inverter based LED tube light fitting, 22/24 watt, indoor decorative high lumen batten and connecting up with twin core twisted flexible copper wire complete all as specified and directed.

M&L for LED street light/ fitting of capacity 24 watt with LED bulb having high pressure die cast aluminium housing with sealed toughened glass cover suitable for pole mounting, light source SMD LED array with lens of efficiency >120lm/w, operating voltage range 120-280 volt, power factor >0.95 weather protection IP66 including suitable size copper cable three core for connection all as specified and directed.

S&F LED light fitting 1x18W, 220V, AC decorative box type with driver, Holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S&F street light bracket for street light fittings made to shape as directed out of GI Pipe light grade 32mm bore 1.5 mtr long including fixing of light fittings and bracket with MS clamps, nuts and bolts of appropriate size complete all as specified and directed.

S&F ceiling rose surface bakelite 65x50mm, two or three terminal complete all as specified & directed.

Supply and fixing LED luminaire 600 mm X 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

S&F LED light fitting mirror type with high out put diffuser 2 feet 10W 220 Volt AC decorative type with driver, Holder & LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F LED light fitting 1x20W, 220V, AC decorative box type with driver, Holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing ceiling fans complete with blades. Down rods, electronic regulator and accessories, 230 volt, 1200mm sweep, min air delievery 210 CFM with service value 6 BEE five star rated with brushless direct current motor (BLDC) incl taking down existing and deposit with MES all as specified and directed.

Taking down old unserviceable Exhaust fan of any type/size from existing location and deposit in MES store yard and Supply and fix exhaust fan single phase metal body, AC 230 Volt, 50 Hz of size 300mm sweep with louvers shouter complete with all accessories including connecting up from ceiling rose to motor all as specified and directed. Make- HAVELLS/BAJAJ/ORIENT

Supply and fixing sheet metal enclosure double door type for DBs single pole and neutral 12 way 240 V with 200 Amp bus bar including blanking plates where required . Make : Indoasian, Legrand, Schiender, Havells etc.

Supply and fixing sheet metal enclosure double door type for DBs single pole and neutral 8 way 240 V with 200 Amp bus bar including blanking plates where required . Make : Indoasian, Legrand, Schiender, Havells etc.

Supply and fixing sheet metal enclosure single door type for DBs single pole and neutral 2 way 240 V with 200 Amp bus bar including blanking plates where required . Make : Indoasian, Legrand, Schiender, Havells etc.

M & L for of sub main wiring complete with 2 run of 6 sqmm single core copper conductor (ISI marked)cable 1100 volts grade,FRLS type, PVC insulated, unsheathed,flexible,multi stranded colour coded cables drawn through rigid PVC conduit of size 25 mm dia medium grade(MMS) with all connected accessories such as Bend,Tee,Elbow,Short peices etc concealed in wall/roofs/floors and including one run of 2.5 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade,FRLS type as earth continuity conductor connected to common earth dolly including making good the disturbed surfaces to match with existing surface including taking down of old existing submain cable complete all as specified and directed. Note : - Two run of 6 sqmm single core copper conductor cable and one run of 2.5 sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit. Make of Cable Havells, KEI, Anchor.

Supply & fix MCB SPN 50 to 63 Amps 10 KA,"C" series,AC,240Volts,50Hz, ISI marked complete all as specified and directed Make - Legrand, Schiender, Havells etc.

Supply, laying and testing XLPE insulated electric cable (heavy duty) with stranded aluminium conductor, 1100 volts grade, heavy duty cable, cross-sectional area 16 Sqmm 4 core connected with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed, laid in trenches or passing through pipes including taking down old existing unserviceable cable complete all as specified and directed. (Earth work, brick protection and sand cushioning shall be measured and paid for separately) Make POLYCAB, GLOSTER, GRANDLAY

S&F Earthing of galvanized steel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr depth below normal ground level) with top edge of earth not less than 1.5 metre below normal ground level, surrounded on all sides by 150mm thick charcoal & common salt starting from ground below earth plate upto 150mm above GI plate in alternate layers connected to and including earth lead wire 4.0mm (8SWG) by means of steel bolts, nuts, check nuts and washers, test point made of GI strip 40x8mm, 10cm long PCC 1:2:4, type B-1 in pit with precast RCC 1:2:4 type B-1 in cover reinforced with XPM not less than 4 Kg per Sqm with 15mm bore GI light grade protection pipe, 20mm bore GI medium grade watering pipe with funnel including charcoal, dust, salt, all as shown in electrical plate No 3 of SSR Part-I (2009) including taking down old existing earthing complete with necessary earth work in any type of soil, removal to a distance not exceeding 50 mtr, including testing on completion, complete all as specified & directed. Note : (a) The cost of earth work, PCC pit of size shown in electrical plate No.3, funnel, watering pipe, wire mesh, charcoal, dust, common salt, 20mm bore medium grade watering pipe & 15mm bore light grade GI pipe as protection to earth lead wire etc shall be deemed included in the unit rate for earthing. (b) After completion, during testing, if the earth resistance equal or less 2 ohms is not obtained, earthing will be regenerated at no extra cost till the desired earth resistance is obtained.

Supply and fix MCCB TPN 415 volts 16 KA, 63 Amp suitable for TPN vertical loadline DB complete all as specified Make : Indoasian, Legrand, Schiender, Havells etc.

Supply & fix MCB SP 5 to 32 Amps 10 KA,"C" series,AC,240 Volts,50Hz , ISI marked complete all as specified and directed (In accordance with IS/IEC 60898-1) 240 V/, 50 Hz, 10 kA Suitable) complete all as specified and directed. Make : Legrand, Schiender, Havells etc.

Supply & fix and in repair MCB SPN 20 Amps 10 KA,"C" series,AC, 240Volts, 50Hz, ISI marked complete all as specified and directed Make : Legrand, Schiender, Havells etc.

Supply & fix and in repair MCB SPN 40 Amps 10 KA,"C" series,AC, 240Volts, 50Hz, ISI marked complete all as specified and directed Make : Legrand, Schiender, Havells etc.