"1) MAS Division- Casual Renewal of Switches, Crossings, Rails, Plain track sleepers and P&C sleepers. 2) MAS-AJJ section- Conversion of FP track to LWR at ADEN/ Central subdivision. "

Schedule of Rates 2021 (Formation, Br & Pway works) for Chennai Division.

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

Item- 1 C.MAS - AJJ Section : CASUAL RENEWAL OF CURVED SWITCHES 60kg 1 in 8.5 at MAS & VLK

S No. Item Description of Item Unit Qty Rate Amount

Lubrication of Plate/Rail screws of Points and

crossings, SEJs, Bridges, Curves etc., with greases

graphite, including removal of screws carefully

without damaging sleepers, cleaning with wire

brush etc., both screws and dowel hole, applying

grease graphite, refixing the screw and sealing

the top and sides of screw with grease graphite to

prevent ingress of moisture and corrosion with

contractors labour, tools, consumables under

traffic condition all lead and lift complete.

1 063122 By using Contractor's Grease Graphite Each 348.00 42.74 14873.52

2 063140 Renewal of seized Plate/Rail screws on PSC Each 30.00 275.98 8279.40

Sleepers by using gas or any approved methods,

duly drilling holes in broken screw and removing

existing screw pieces from the holes along with

existing dowels and fixing new contractor's

dowels (procured from RDSO approved sources)

and grouting around dowel with Epoxy materials

of approved specification and refixing new

Railway's rail/Plate screws duly greasing the

screw with specified grease with all contractor's

materials, consumables, tools & plants, labour

with all lead, lift. Note: 1.Seized screws shall be

identified and marked by JE/P.Way and verified at

minimum SSE/P.Way In charge) level. 2. Due care

shall be taken to avoid any damage to the

sleeper 3.A penalty of 50% of the basic cost of

new sleeper in nearest sleeper factory shall be

levied on each, if sleeper gets damaged in the

Renewal of Switch Rails (Tongue rails, Stock rails

and fittings) of all rail sections, under line block

conditions ensuring proper housing & changing of

stretcher bars and fittings as required. Work also

includes drilling of hole, if any, and leading of

rails laying anywhere in station yard to site of

work. Released switch rails shall be stacked at

indicated place in a countable manner within the

lead of 250m & all lift, clear of infringements,

crossing of track, if any complete, as directed.

with contractor's vehicles, consumables, stores,

labour etc. complete, as directed by engineer in-

charge. Note: 1).One set means Two Tongue rails

and Two Stock rails (2) One tongue & stock rail

shall be considered as 1/2 set. (3) One tongue rail

or one Stock rail shall be considered as 1/4 Set.

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

4 092030 25mm gap 'in-situ' welding during traffic block Each 3.00 1806.57 5419.71

using Railway's welding portion & Welder and

finishing of weld to meet the prescribed

tolerances and pass all stipulated tests with all

required labour, materials, consumables, tools,

equipments etc. to complete the work in all

respect as per IR's "Manual for Fusion Welding of

Rails by Alumino - Thermic Process" with latest

correction slips, including marking of welded

joint, painting weld collar with anticorrosive paint,

restoration of track near weld joint to original

position and fixing of joggled fish plate at new

weld, to be removed after passing of weld in

USFD test as directed by Engineer in charge.

Note: 1. Only welding portion and related

accessories as per Annexure - I and Welder shall

be supplied by Railways. 2. Hydraulic Weld

trimmer shall be used for chipping and profile

Grinder for finishing. 3. Required nos. of Joggled

fish plates shall be supplied by Railway at

nearest P. Way Stores and the same shall be

returned at nearest P. Way Store or at other

location as per direction of Engineer-in-Charge

after release from track.

5 157020 Carrying out ancillary works required for UTV Shift 4.00 2553.45 10213.80

working under line block i.e., turning of rails/

Sleepers and keeping in position for fixing of UTV

clamps to rail, keeping rails/PSC Sleepers in

position while loading into BFR, removal of

clamps on BFR for releasing loaded rail/Sleepers,

adjusting of rails/Sleepers on BFR etc. by

providing minimum of three men in a shift of 8

hours, with all contractor's tools, all lead, lift,

crossing of tracks etc., complete and as directed

by the engineer - in - charge. Note: In case,

contractor provides less no. of Labour, payment

will be deducted for each such person @ 2/3 rd of

the accepted item rate.

Quick cutting with abrasive rail cutter of all types

of rail sections including wear resistant, head

hardened rails up to 110 UTS, with contractors

tools & plants, equipment, consumable with all

lead & lift etc. complete as directed by Engineer

in-charge. Abrasive Rail Cutter will be as per

RDSO Specification No. TM/SM/1 (Rev. 01 of

2012) with latest status of RDSO; Rail Cutting

Wheel Abrasive Disc will be as per RDSO

Specification No.TM/SM/2 (Rev. 01 of 2020)

Drilling holes of 16 mm to 32 mm dia. with Rail

Drilling machine including chamfering with

appropriate chamfering tools in all types of rail

section with contractor's tools & plants,

equipment, consumable with all lead & lift etc.

complete, as directed by Engineer in-charge. Rail

Drilling Machine will be as per RDSO Specification

No. TM/SM/3, dated 24.04.1991.

Loading of rails of any section and length up to

1 3 metres in Wagons / Truck / trailer including

lead up to 50 metres and lift up to 5 metres.

8 171014 In Wagon where mechanical handling is possible MT 7.05 165.78 1168.75

and traffic block is not required or in Truck/trailer.

Loading, leading and unloading of 52Kg / 60Kg

rail up to 13 metre length by Railway's Rail Dolly /

Dip Lorry to the nominated location under traffic

with line protection in case road carriage is not

possible with different lead with a lift up to 5

metre during block period.

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

Transportation of Rails, sleepers, switches,

crossings, SEJs and Glued Joints by road vehicles

for different leads. Note: 1 . Lead shall be the

shortest motorable road length between the

points of loading and unloading. 2. Loading and

unloading shall be paid extra under relevant

12 172058 Extra for every Km per MT beyond 150 Km over MT-Km 1410.00 3.30 4653.00

item no. 172057

Unloading of Switches / Crossings / SEJ Rails /

Glued Joints of any rail section and length with or

w itho ut P.Way fittings & fastenings in neat

manner for Railway usage from departmental

material train (DMT) or contractor's / Railway's

Truck/Trailer with lead up to 250 metre & lift up

Collection, segregation and stacking of various

scattered P.Way materials at nominated stacking

location with serviceable and un-serviceable ones

separately within a lead up to 500 metre and lift

up to 5 metre including crossing of track(s)

wherever necessary as directed by Engineer-in-

14 173031 Rails, switches, crossings, SEJ, Glued Joints, MT 7.05 500.78 3530.50

Check Rails etc.

15 173033 P.Way fittings of all types and other similar loose MT 2.61 430.26 1122.98

Hiring of machinery for minor miscellaneous

works for short duration including operator/driver,

fuel, lubricants and consumable. The contractor

shall arrange all statutory permits as required by

rules and regulations prevailing in the area of

work. Payment shall be made for actual working

16 211202 Hydra or similar tyre mounted Pick-n-Carry crane Hour 50.00 1459.19 72959.50

of 12T capacity for misc. works of handling of

a.MAS - AJJ Section : CASUAL RENEWAL OF CURVED SWITCHES 52 kg 1 in 8.5 at BBQ coaching yd &

S No. Item Description of Item Unit Qty Rate Amount

Lubrication of Plate/Rail screws of Points and

crossings, SEJs, Bridges, Curves etc., with greases

graphite, including removal of screws carefully

without damaging sleepers, cleaning with wire

brush etc., both screws and dowel hole, applying

grease graphite, refixing the screw and sealing

the top and sides of screw with grease graphite to

prevent ingress of moisture and corrosion with

contractors labour, tools, consumables under

traffic condition all lead and lift complete.

1 063122 By using Contractor's Grease Graphite Each 928.00 42.74 39662.72

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

2 063140 Renewal of seized Plate/Rail screws on PSC Each 80.00 275.98 22078.40

Sleepers by using gas or any approved methods,

duly drilling holes in broken screw and removing

existing screw pieces from the holes along with

existing dowels and fixing new contractor's

dowels (procured from RDSO approved sources)

and grouting around dowel with Epoxy materials

of approved specification and refixing new

Railway's rail/Plate screws duly greasing the

screw with specified grease with all contractor's

materials, consumables, tools & plants, labour

with all lead, lift. Note: 1.Seized screws shall be

identified and marked by JE/P.Way and verified at

minimum SSE/P.Way In charge) level. 2. Due care

shall be taken to avoid any damage to the

sleeper 3.A penalty of 50% of the basic cost of

new sleeper in nearest sleeper factory shall be

levied on each, if sleeper gets damaged in the

Renewal of Switch Rails (Tongue rails, Stock rails

and fittings) of all rail sections, under line block

conditions ensuring proper housing & changing of

stretcher bars and fittings as required. Work also

includes drilling of hole, if any, and leading of

rails laying anywhere in station yard to site of

work. Released switch rails shall be stacked at

indicated place in a countable manner within the

lead of 250m & all lift, clear of infringements,

crossing of track, if any complete, as directed.

with contractor's vehicles, consumables, stores,

labour etc. complete, as directed by engineer in-

charge. Note: 1).One set means Two Tongue rails

and Two Stock rails (2) One tongue & stock rail

shall be considered as 1/2 set. (3) One tongue rail

or one Stock rail shall be considered as 1/4 Set.

4 092030 25mm gap 'in-situ' welding during traffic block Each 48.00 1806.57 86715.36

using Railway's welding portion & Welder and

finishing of weld to meet the prescribed

tolerances and pass all stipulated tests with all

required labour, materials, consumables, tools,

equipments etc. to complete the work in all

respect as per IR's "Manual for Fusion Welding of

Rails by Alumino - Thermic Process" with latest

correction slips, including marking of welded

joint, painting weld collar with anticorrosive paint,

restoration of track near weld joint to original

position and fixing of joggled fish plate at new

weld, to be removed after passing of weld in

USFD test as directed by Engineer in charge.

Note: 1. Only welding portion and related

accessories as per Annexure - I and Welder shall

be supplied by Railways. 2. Hydraulic Weld

trimmer shall be used for chipping and profile

Grinder for finishing. 3. Required nos. of Joggled

fish plates shall be supplied by Railway at

nearest P. Way Stores and the same shall be

returned at nearest P. Way Store or at other

location as per direction of Engineer-in-Charge

after release from track.

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

5 157020 Carrying out ancillary works required for UTV Shift 4.00 2553.45 10213.80

working under line block i.e., turning of rails/

Sleepers and keeping in position for fixing of UTV

clamps to rail, keeping rails/PSC Sleepers in

position while loading into BFR, removal of

clamps on BFR for releasing loaded rail/Sleepers,

adjusting of rails/Sleepers on BFR etc. by

providing minimum of three men in a shift of 8

hours, with all contractor's tools, all lead, lift,

crossing of tracks etc., complete and as directed

by the engineer - in - charge. Note: In case,

contractor provides less no. of Labour, payment

will be deducted for each such person @ 2/3 rd of

the accepted item rate.

Quick cutting with abrasive rail cutter of all types

of rail sections including wear resistant, head

hardened rails up to 110 UTS, with contractors

tools & plants, equipment, consumable with all

lead & lift etc. complete as directed by Engineer

in-charge. Abrasive Rail Cutter will be as per

RDSO Specification No. TM/SM/1 (Rev. 01 of

2012) with latest status of RDSO; Rail Cutting

Wheel Abrasive Disc will be as per RDSO

Specification No.TM/SM/2 (Rev. 01 of 2020)

Drilling holes of 16 mm to 32 mm dia. with Rail

Drilling machine including chamfering with

appropriate chamfering tools in all types of rail

section with contractor's tools & plants,

equipment, consumable with all lead & lift etc.

complete, as directed by Engineer in-charge. Rail

Drilling Machine will be as per RDSO Specification

No. TM/SM/3, dated 24.04.1991.

Loading of rails of any section and length up to

1 3 metres in Wagons / Truck / trailer including

lead up to 50 metres and lift up to 5 metres.

8 171014 In Wagon where mechanical handling is possible MT 18.80 165.78 3116.66

and traffic block is not required or in Truck/trailer.

Loading, leading and unloading of 52Kg / 60Kg

rail up to 13 metre length by Railway's Rail Dolly /

Dip Lorry to the nominated location under traffic

with line protection in case road carriage is not

possible with different lead with a lift up to 5

metre during block period.

Transportation of Rails, sleepers, switches,

crossings, SEJs and Glued Joints by road vehicles

for different leads. Note: 1 . Lead shall be the

shortest motorable road length between the

points of loading and unloading. 2. Loading and

unloading shall be paid extra under relevant

12 172058 Extra for every Km per MT beyond 150 Km over MT-Km 1880.00 3.30 6204.00

item no. 172057

Unloading of Switches / Crossings / SEJ Rails /

Glued Joints of any rail section and length with or

w itho ut P.Way fittings & fastenings in neat

manner for Railway usage from departmental

material train (DMT) or contractor's / Railway's

Truck/Trailer with lead up to 250 metre & lift up

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

Collection, segregation and stacking of various

scattered P.Way materials at nominated stacking

location with serviceable and un-serviceable ones

separately within a lead up to 500 metre and lift

up to 5 metre including crossing of track(s)

wherever necessary as directed by Engineer-in-

14 173031 Rails, switches, crossings, SEJ, Glued Joints, MT 18.80 500.78 9414.66

Check Rails etc.

15 173033 P.Way fittings of all types and other similar loose MT 6.96 430.26 2994.61

Hiring of machinery for minor miscellaneous

works for short duration including operator/driver,

fuel, lubricants and consumable. The contractor

shall arrange all statutory permits as required by

rules and regulations prevailing in the area of

work. Payment shall be made for actual working

16 211202 Hydra or similar tyre mounted Pick-n-Carry crane Hour 35.00 1459.19 51071.65

of 12T capacity for misc. works of handling of

Item- 1 b.MAS - AJJ Section : CASUAL RENEWAL OF CURVED SWITCHES 52 kg 1 in 12 at MAS

S No. Item Description of Item Unit Qty Rate Amount

Lubrication of Plate/Rail screws of Points and

crossings, SEJs, Bridges, Curves etc., with greases

graphite, including removal of screws carefully

without damaging sleepers, cleaning with wire

brush etc., both screws and dowel hole, applying

grease graphite, refixing the screw and sealing

the top and sides of screw with grease graphite to

prevent ingress of moisture and corrosion with

contractors labour, tools, consumables under

traffic condition all lead and lift complete.

1 063122 By using Contractor's Grease Graphite Each 406.00 42.74 17352.44

2 063140 Renewal of seized Plate/Rail screws on PSC Each 30.00 275.98 8279.40

Sleepers by using gas or any approved methods,

duly drilling holes in broken screw and removing

existing screw pieces from the holes along with

existing dowels and fixing new contractor's

dowels (procured from RDSO approved sources)

and grouting around dowel with Epoxy materials

of approved specification and refixing new

Railway's rail/Plate screws duly greasing the

screw with specified grease with all contractor's

materials, consumables, tools & plants, labour

with all lead, lift. Note: 1.Seized screws shall be

identified and marked by JE/P.Way and verified at

minimum SSE/P.Way In charge) level. 2. Due care

shall be taken to avoid any damage to the

sleeper 3.A penalty of 50% of the basic cost of

new sleeper in nearest sleeper factory shall be

levied on each, if sleeper gets damaged in the

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

Renewal of Switch Rails (Tongue rails, Stock rails

and fittings) of all rail sections, under line block

conditions ensuring proper housing & changing of

stretcher bars and fittings as required. Work also

includes drilling of hole, if any, and leading of

rails laying anywhere in station yard to site of

work. Released switch rails shall be stacked at

indicated place in a countable manner within the

lead of 250m & all lift, clear of infringements,

crossing of track, if any complete, as directed.

with contractor's vehicles, consumables, stores,

labour etc. complete, as directed by engineer in-

charge. Note: 1).One set means Two Tongue rails

and Two Stock rails (2) One tongue & stock rail

shall be considered as 1/2 set. (3) One tongue rail

or one Stock rail shall be considered as 1/4 Set.

4 092030 25mm gap 'in-situ' welding during traffic block Each 12.00 1806.57 21678.84

using Railway's welding portion & Welder and

finishing of weld to meet the prescribed

tolerances and pass all stipulated tests with all

required labour, materials, consumables, tools,

equipments etc. to complete the work in all

respect as per IR's "Manual for Fusion Welding of

Rails by Alumino - Thermic Process" with latest

correction slips, including marking of welded

joint, painting weld collar with anticorrosive paint,

restoration of track near weld joint to original

position and fixing of joggled fish plate at new

weld, to be removed after passing of weld in

USFD test as directed by Engineer in charge.

Note: 1. Only welding portion and related

accessories as per Annexure - I and Welder shall

be supplied by Railways. 2. Hydraulic Weld

trimmer shall be used for chipping and profile

Grinder for finishing. 3. Required nos. of Joggled

fish plates shall be supplied by Railway at

nearest P. Way Stores and the same shall be

returned at nearest P. Way Store or at other

location as per direction of Engineer-in-Charge

after release from track.

5 157020 Carrying out ancillary works required for UTV Shift 2.00 2553.45 5106.90

working under line block i.e., turning of rails/

Sleepers and keeping in position for fixing of UTV

clamps to rail, keeping rails/PSC Sleepers in

position while loading into BFR, removal of

clamps on BFR for releasing loaded rail/Sleepers,

adjusting of rails/Sleepers on BFR etc. by

providing minimum of three men in a shift of 8

hours, with all contractor's tools, all lead, lift,

crossing of tracks etc., complete and as directed

by the engineer - in - charge. Note: In case,

contractor provides less no. of Labour, payment

will be deducted for each such person @ 2/3 rd of

the accepted item rate.

Quick cutting with abrasive rail cutter of all types

of rail sections including wear resistant, head

hardened rails up to 110 UTS, with contractors

tools & plants, equipment, consumable with all

lead & lift etc. complete as directed by Engineer

in-charge. Abrasive Rail Cutter will be as per

RDSO Specification No. TM/SM/1 (Rev. 01 of

2012) with latest status of RDSO; Rail Cutting

Wheel Abrasive Disc will be as per RDSO

Specification No.TM/SM/2 (Rev. 01 of 2020)

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

Drilling holes of 16 mm to 32 mm dia. with Rail

Drilling machine including chamfering with

appropriate chamfering tools in all types of rail

section with contractor's tools & plants,

equipment, consumable with all lead & lift etc.

complete, as directed by Engineer in-charge. Rail

Drilling Machine will be as per RDSO Specification

No. TM/SM/3, dated 24.04.1991.

Loading of rails of any section and length up to

1 3 metres in Wagons / Truck / trailer including

lead up to 50 metres and lift up to 5 metres.

8 171014 In Wagon where mechanical handling is possible MT 4.70 165.78 779.17

and traffic block is not required or in Truck/trailer.

Loading, leading and unloading of 52Kg / 60Kg

rail up to 13 metre length by Railway's Rail Dolly /

Dip Lorry to the nominated location under traffic

with line protection in case road carriage is not

possible with different lead with a lift up to 5

metre during block period.

Transportation of Rails, sleepers, switches,

crossings, SEJs and Glued Joints by road vehicles

for different leads. Note: 1 . Lead shall be the

shortest motorable road length between the

points of loading and unloading. 2. Loading and

unloading shall be paid extra under relevant

12 172058 Extra for every Km per MT beyond 150 Km over MT-Km 940.00 3.30 3102.00

item no. 172057

Unloading of Switches / Crossings / SEJ Rails /

Glued Joints of any rail section and length with or

w itho ut P.Way fittings & fastenings in neat

manner for Railway usage from departmental

material train (DMT) or contractor's / Railway's

Truck/Trailer with lead up to 250 metre & lift up

Collection, segregation and stacking of various

scattered P.Way materials at nominated stacking

location with serviceable and un-serviceable ones

separately within a lead up to 500 metre and lift

up to 5 metre including crossing of track(s)

wherever necessary as directed by Engineer-in-

14 173031 Rails, switches, crossings, SEJ, Glued Joints, MT 4.70 500.78 2353.67

Check Rails etc.

15 173033 P.Way fittings of all types and other similar loose MT 1.74 430.26 748.65

Hiring of machinery for minor miscellaneous

works for short duration including operator/driver,

fuel, lubricants and consumable. The contractor

shall arrange all statutory permits as required by

rules and regulations prevailing in the area of

work. Payment shall be made for actual working

16 211202 Hydra or similar tyre mounted Pick-n-Carry crane Hour 50.00 1459.19 72959.50

of 12T capacity for misc. works of handling of

d.MAS - AJJ Section : CASUAL RENEWAL OF CURVED SWITCHES 60kg 1 in 12 at MAS, MCPK,MMC,

S No. Item Description of Item Unit Qty Rate Amount

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

Lubrication of Plate/Rail screws of Points and

crossings, SEJs, Bridges, Curves etc., with greases

graphite, including removal of screws carefully

without damaging sleepers, cleaning with wire

brush etc., both screws and dowel hole, applying

grease graphite, refixing the screw and sealing

the top and sides of screw with grease graphite to

prevent ingress of moisture and corrosion with

contractors labour, tools, consumables under

traffic condition all lead and lift complete.

1 063122 By using Contractor's Grease Graphite Each 2233.00 42.74 95438.42

2 063140 Renewal of seized Plate/Rail screws on PSC Each 165.00 275.98 45536.70

Sleepers by using gas or any approved methods,

duly drilling holes in broken screw and removing

existing screw pieces from the holes along with

existing dowels and fixing new contractor's

dowels (procured from RDSO approved sources)

and grouting around dowel with Epoxy materials

of approved specification and refixing new

Railway's rail/Plate screws duly greasing the

screw with specified grease with all contractor's

materials, consumables, tools & plants, labour

with all lead, lift. Note: 1.Seized screws shall be

identified and marked by JE/P.Way and verified at

minimum SSE/P.Way In charge) level. 2. Due care

shall be taken to avoid any damage to the

sleeper 3.A penalty of 50% of the basic cost of

new sleeper in nearest sleeper factory shall be

levied on each, if sleeper gets damaged in the

Renewal of Switch Rails (Tongue rails, Stock rails

and fittings) of all rail sections, under line block

conditions ensuring proper housing & changing of

stretcher bars and fittings as required. Work also

includes drilling of hole, if any, and leading of

rails laying anywhere in station yard to site of

work. Released switch rails shall be stacked at

indicated place in a countable manner within the

lead of 250m & all lift, clear of infringements,

crossing of track, if any complete, as directed.

with contractor's vehicles, consumables, stores,

labour etc. complete, as directed by engineer in-

charge. Note: 1).One set means Two Tongue rails

and Two Stock rails (2) One tongue & stock rail

shall be considered as 1/2 set. (3) One tongue rail

or one Stock rail shall be considered as 1/4 Set.

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

4 092030 25mm gap 'in-situ' welding during traffic block Each 66.00 1806.57 119233.62

using Railway's welding portion & Welder and

finishing of weld to meet the prescribed

tolerances and pass all stipulated tests with all

required labour, materials, consumables, tools,

equipments etc. to complete the work in all

respect as per IR's "Manual for Fusion Welding of

Rails by Alumino - Thermic Process" with latest

correction slips, including marking of welded

joint, painting weld collar with anticorrosive paint,

restoration of track near weld joint to original

position and fixing of joggled fish plate at new

weld, to be removed after passing of weld in

USFD test as directed by Engineer in charge.

Note: 1. Only welding portion and related

accessories as per Annexure - I and Welder shall

be supplied by Railways. 2. Hydraulic Weld

trimmer shall be used for chipping and profile

Grinder for finishing. 3. Required nos. of Joggled

fish plates shall be supplied by Railway at

nearest P. Way Stores and the same shall be

returned at nearest P. Way Store or at other

location as per direction of Engineer-in-Charge

after release from track.

5 157020 Carrying out ancillary works required for UTV Shift 12.00 2553.45 30641.40

working under line block i.e., turning of rails/

Sleepers and keeping in position for fixing of UTV

clamps to rail, keeping rails/PSC Sleepers in

position while loading into BFR, removal of

clamps on BFR for releasing loaded rail/Sleepers,

adjusting of rails/Sleepers on BFR etc. by

providing minimum of three men in a shift of 8

hours, with all contractor's tools, all lead, lift,

crossing of tracks etc., complete and as directed

by the engineer - in - charge. Note: In case,

contractor provides less no. of Labour, payment

will be deducted for each such person @ 2/3 rd of

the accepted item rate.

Quick cutting with abrasive rail cutter of all types

of rail sections including wear resistant, head

hardened rails up to 110 UTS, with contractors

tools & plants, equipment, consumable with all

lead & lift etc. complete as directed by Engineer

in-charge. Abrasive Rail Cutter will be as per

RDSO Specification No. TM/SM/1 (Rev. 01 of

2012) with latest status of RDSO; Rail Cutting

Wheel Abrasive Disc will be as per RDSO

Specification No.TM/SM/2 (Rev. 01 of 2020)

Loading of rails of any section and length up to

1 3 metres in Wagons / Truck / trailer including

lead up to 50 metres and lift up to 5 metres.

7 171014 In Wagon where mechanical handling is possible MT 25.85 165.78 4285.41

and traffic block is not required or in Truck/trailer.

Loading, leading and unloading of 52Kg / 60Kg

rail up to 13 metre length by Railway's Rail Dolly /

Dip Lorry to the nominated location under traffic

with line protection in case road carriage is not

possible with different lead with a lift up to 5

metre during block period.

Transportation of Rails, sleepers, switches,

crossings, SEJs and Glued Joints by road vehicles

for different leads. Note: 1 . Lead shall be the

shortest motorable road length between the

points of loading and unloading. 2. Loading and

unloading shall be paid extra under relevant

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

11 172058 Extra for every Km per MT beyond 150 Km over MT-Km 5170.00 3.30 17061.00

item no. 172057

Unloading of Switches / Crossings / SEJ Rails /

Glued Joints of any rail section and length with or

w itho ut P.Way fittings & fastenings in neat

manner for Railway usage from departmental

material train (DMT) or contractor's / Railway's

Truck/Trailer with lead up to 250 metre & lift up

Collection, segregation and stacking of various

scattered P.Way materials at nominated stacking

location with serviceable and un-serviceable ones

separately within a lead up to 500 metre and lift

up to 5 metre including crossing of track(s)

wherever necessary as directed by Engineer-in-

13 173031 Rails, switches, crossings, SEJ, Glued Joints, MT 25.85 500.78 12945.16

Check Rails etc.

14 173033 P.Way fittings of all types and other similar loose MT 9.57 430.26 4117.59

Hiring of machinery for minor miscellaneous

works for short duration including operator/driver,

fuel, lubricants and consumable. The contractor

shall arrange all statutory permits as required by

rules and regulations prevailing in the area of

work. Payment shall be made for actual working

15 211202 Hydra or similar tyre mounted Pick-n-Carry crane Hour 100.00 1459.19 145919.00

of 12T capacity for misc. works of handling of

e.MAS - AJJ Section : Casual Renewal of 60kg 1 in 12 CMS Crossings 35 Nos (CASUAL RENEWAL OF

60 Kg 1 in 12 CMS CROSSINGS-MAS- 132B, 130B; TRL-50A,51A,52A,53B,54A&B; TI-51A&B,

62A,65B,66A&B;MMC- 65A,56A,63,65B; BBQ- 51B, 50A; VPY- 59A,59B; VLK-

S No. Item Description of Item Unit Qty Rate Amount

Dismantling and removing rail of all section &

length from track, laid on any type & density of

sleeper by removing fish plates, fastenings & fish

bolts and other materials including stacking all

released materials within an average distance of

500 metres as directed by Engineer in-charge.

Note: 1.Cutting of rails shall be paid separately.

2.Work to be done under traffic block.

Insertion of rails of all types & length in track, laid

on any type & density of sleeper to the specified

gauge under traffic block. Rates include fastening

of rail with sleepers with standard set of

fastenings and fixing of fish plates and bolts or, if

required, providing gap for welding and stacking

of released material without infringement within

250m as directed by Engineer-in-Charge. Note:

Rail drilling and cutting to be paid separately.

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

Renewal of CMS Crossing of all rail sections with

CMS crossing or with WCMS crossing complete

w ith fastenings including replacement of worn-

out rubber pads, liners and ERC, as required. All

the released materials shall be stacked at

specified location in a countable manner within

the lead of 500m & all lift, clear of infringements,

crossing of track, if any complete, as directed.

with contractor's vehicles, consumables, stores,

labour etc. complete, as directed by engineer in-

charge. Note: Rail cutting and drilling shall be

paid separately under relevant item.

4 092030 25mm gap 'in-situ' welding during traffic block Each 140.00 1806.57 252919.80

using Railway's welding portion & Welder and

finishing of weld to meet the prescribed

tolerances and pass all stipulated tests with all

required labour, materials, consumables, tools,

equipments etc. to complete the work in all

respect as per IR's "Manual for Fusion Welding of

Rails by Alumino - Thermic Process" with latest

correction slips, including marking of welded

joint, painting weld collar with anticorrosive paint,

restoration of track near weld joint to original

position and fixing of joggled fish plate at new

weld, to be removed after passing of weld in

USFD test as directed by Engineer in charge.

Note: 1. Only welding portion and related

accessories as per Annexure - I and Welder shall

be supplied by Railways. 2. Hydraulic Weld

trimmer shall be used for chipping and profile

Grinder for finishing. 3. Required nos. of Joggled

fish plates shall be supplied by Railway at

nearest P. Way Stores and the same shall be

returned at nearest P. Way Store or at other

location as per direction of Engineer-in-Charge

after release from track.

Quick cutting with abrasive rail cutter of all types

of rail sections including wear resistant, head

hardened rails up to 110 UTS, with contractors

tools & plants, equipment, consumable with all

lead & lift etc. complete as directed by Engineer

in-charge. Abrasive Rail Cutter will be as per

RDSO Specification No. TM/SM/1 (Rev. 01 of

2012) with latest status of RDSO; Rail Cutting

Wheel Abrasive Disc will be as per RDSO

Specification No.TM/SM/2 (Rev. 01 of 2020)

Drilling holes of 16 mm to 32 mm dia. with Rail

Drilling machine including chamfering with

appropriate chamfering tools in all types of rail

section with contractor's tools & plants,

equipment, consumable with all lead & lift etc.

complete, as directed by Engineer in-charge. Rail

Drilling Machine will be as per RDSO Specification

No. TM/SM/3, dated 24.04.1991.

7 161050 Drilling holes of specified size for bond holes with Each 280.00 53.93 15100.40

7.2mm dia drill twist to correct spacing and

location on 60kg/52kg rails on cess or under

traffic block with contractor's tools and plant,

equipment, consumable, labour etc complete as

directed by the Engineer in charge at site.

Loading of tongue rail, stock rail, switch assembly

and crossings of any section and length, SEJ,

Glued joint etc. with / without P.Way fittings and

fastenings, in Wagon / Truck / trailer including

lead up to 250 metre and lift up to 5 metre.

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

8 171024 In Wagon where mechanical handling is possible MT 54.43 161.36 8782.82

and traffic block is not required or in Truck/trailer.

Loading, leading and unloading of 52Kg / 60Kg

rail up to 13 metre length by Railway's Rail Dolly /

Dip Lorry to the nominated location under traffic

with line protection in case road carriage is not

possible with different lead with a lift up to 5

metre during block period.

Transportation of Rails, sleepers, switches,

crossings, SEJs and Glued Joints by road vehicles

for different leads. Note: 1 . Lead shall be the

shortest motorable road length between the

points of loading and unloading. 2. Loading and

unloading shall be paid extra under relevant

11 172058 Extra for every Km per MT beyond 150 Km over MT-Km 2721.50 3.30 8980.95

item no. 172057

Unloading of Switches / Crossings / SEJ Rails /

Glued Joints of any rail section and length with or

w itho ut P.Way fittings & fastenings in neat

manner for Railway usage from departmental

material train (DMT) or contractor's / Railway's

Truck/Trailer with lead up to 250 metre & lift up

Collection, segregation and stacking of various

scattered P.Way materials at nominated stacking

location with serviceable and un-serviceable ones

separately within a lead up to 500 metre and lift

up to 5 metre including crossing of track(s)

wherever necessary as directed by Engineer-in-

13 173031 Rails, switches, crossings, SEJ, Glued Joints, MT 54.43 500.78 27257.46

Check Rails etc.

14 173033 P.Way fittings of all types and other similar loose MT 6.47 430.26 2783.78

f.MAS - AJJ Section : Casual Renewal of 60kg 1 in 8.5 CMS Crossings (CASUAL RENEWAL OF 60 Kg 1

in 8.5 CMS CROSSINGS-BBQ Coaching yd, MMC, BBQ, VPY,PEW &VLK.

S No. Item Description of Item Unit Qty Rate Amount

Dismantling and removing rail of all section &

length from track, laid on any type & density of

sleeper by removing fish plates, fastenings & fish

bolts and other materials including stacking all

released materials within an average distance of

500 metres as directed by Engineer in-charge.

Note: 1.Cutting of rails shall be paid separately.

2.Work to be done under traffic block.

Insertion of rails of all types & length in track, laid

on any type & density of sleeper to the specified

gauge under traffic block. Rates include fastening

of rail with sleepers with standard set of

fastenings and fixing of fish plates and bolts or, if

required, providing gap for welding and stacking

of released material without infringement within

250m as directed by Engineer-in-Charge. Note:

Rail drilling and cutting to be paid separately.

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

Renewal of CMS Crossing of all rail sections with

CMS crossing or with WCMS crossing complete

w ith fastenings including replacement of worn-

out rubber pads, liners and ERC, as required. All

the released materials shall be stacked at

specified location in a countable manner within

the lead of 500m & all lift, clear of infringements,

crossing of track, if any complete, as directed.

with contractor's vehicles, consumables, stores,

labour etc. complete, as directed by engineer in-

charge. Note: Rail cutting and drilling shall be

paid separately under relevant item.

4 092030 25mm gap 'in-situ' welding during traffic block Each 76.00 1806.57 137299.32

using Railway's welding portion & Welder and

finishing of weld to meet the prescribed

tolerances and pass all stipulated tests with all

required labour, materials, consumables, tools,

equipments etc. to complete the work in all

respect as per IR's "Manual for Fusion Welding of

Rails by Alumino - Thermic Process" with latest

correction slips, including marking of welded

joint, painting weld collar with anticorrosive paint,

restoration of track near weld joint to original

position and fixing of joggled fish plate at new

weld, to be removed after passing of weld in

USFD test as directed by Engineer in charge.

Note: 1. Only welding portion and related

accessories as per Annexure - I and Welder shall

be supplied by Railways. 2. Hydraulic Weld

trimmer shall be used for chipping and profile

Grinder for finishing. 3. Required nos. of Joggled

fish plates shall be supplied by Railway at

nearest P. Way Stores and the same shall be

returned at nearest P. Way Store or at other

location as per direction of Engineer-in-Charge

after release from track.

Quick cutting with abrasive rail cutter of all types

of rail sections including wear resistant, head

hardened rails up to 110 UTS, with contractors

tools & plants, equipment, consumable with all

lead & lift etc. complete as directed by Engineer

in-charge. Abrasive Rail Cutter will be as per

RDSO Specification No. TM/SM/1 (Rev. 01 of

2012) with latest status of RDSO; Rail Cutting

Wheel Abrasive Disc will be as per RDSO

Specification No.TM/SM/2 (Rev. 01 of 2020)

Drilling holes of 16 mm to 32 mm dia. with Rail

Drilling machine including chamfering with

appropriate chamfering tools in all types of rail

section with contractor's tools & plants,

equipment, consumable with all lead & lift etc.

complete, as directed by Engineer in-charge. Rail

Drilling Machine will be as per RDSO Specification

No. TM/SM/3, dated 24.04.1991.

7 161050 Drilling holes of specified size for bond holes with Each 76.00 53.93 4098.68

7.2mm dia drill twist to correct spacing and

location on 60kg/52kg rails on cess or under

traffic block with contractor's tools and plant,

equipment, consumable, labour etc complete as

directed by the Engineer in charge at site.

Loading of tongue rail, stock rail, switch assembly

and crossings of any section and length, SEJ,

Glued joint etc. with / without P.Way fittings and

fastenings, in Wagon / Truck / trailer including

lead up to 250 metre and lift up to 5 metre.

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

8 171024 In Wagon where mechanical handling is possible MT 15.58 161.36 2513.99

and traffic block is not required or in Truck/trailer.

Loading, leading and unloading of 52Kg / 60Kg

rail up to 13 metre length by Railway's Rail Dolly /

Dip Lorry to the nominated location under traffic

with line protection in case road carriage is not

possible with different lead with a lift up to 5

metre during block period.

Transportation of Rails, sleepers, switches,

crossings, SEJs and Glued Joints by road vehicles

for different leads. Note: 1 . Lead shall be the

shortest motorable road length between the

points of loading and unloading. 2. Loading and

unloading shall be paid extra under relevant

11 172058 Extra for every Km per MT beyond 150 Km over MT-Km 3116.00 3.30 10282.80

item no. 172057

Unloading of Switches / Crossings / SEJ Rails /

Glued Joints of any rail section and length with or

w itho ut P.Way fittings & fastenings in neat

manner for Railway usage from departmental

material train (DMT) or contractor's / Railway's

Truck/Trailer with lead up to 250 metre & lift up

Collection, segregation and stacking of various

scattered P.Way materials at nominated stacking

location with serviceable and un-serviceable ones

separately within a lead up to 500 metre and lift

up to 5 metre including crossing of track(s)

wherever necessary as directed by Engineer-in-

13 173031 Rails, switches, crossings, SEJ, Glued Joints, MT 15.58 500.78 7802.15

Check Rails etc.

14 173033 P.Way fittings of all types and other similar loose MT 3.51 430.26 1510.21

g.MAS - AJJ Section : Casual Renewal of 52kg 1 in 8.5 CMS Crossings (CASUAL RENEWAL OF 52 Kg 1

in 12 CMS CROSSINGS-BBQ & VPY

S No. Item Description of Item Unit Qty Rate Amount

Renewal of CMS Crossing of all rail sections with

CMS crossing or with WCMS crossing complete

w ith fastenings including replacement of worn-

out rubber pads, liners and ERC, as required. All

the released materials shall be stacked at

specified location in a countable manner within

the lead of 500m & all lift, clear of infringements,

crossing of track, if any complete, as directed.

with contractor's vehicles, consumables, stores,

labour etc. complete, as directed by engineer in-

charge. Note: Rail cutting and drilling shall be

paid separately under relevant item.

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

2 092030 25mm gap 'in-situ' welding during traffic block Each 24.00 1806.57 43357.68

using Railway's welding portion & Welder and

finishing of weld to meet the prescribed

tolerances and pass all stipulated tests with all

required labour, materials, consumables, tools,

equipments etc. to complete the work in all

respect as per IR's "Manual for Fusion Welding of

Rails by Alumino - Thermic Process" with latest

correction slips, including marking of welded

joint, painting weld collar with anticorrosive paint,

restoration of track near weld joint to original

position and fixing of joggled fish plate at new

weld, to be removed after passing of weld in

USFD test as directed by Engineer in charge.

Note: 1. Only welding portion and related

accessories as per Annexure - I and Welder shall

be supplied by Railways. 2. Hydraulic Weld

trimmer shall be used for chipping and profile

Grinder for finishing. 3. Required nos. of Joggled

fish plates shall be supplied by Railway at

nearest P. Way Stores and the same shall be

returned at nearest P. Way Store or at other

location as per direction of Engineer-in-Charge

after release from track.

Quick cutting with abrasive rail cutter of all types

of rail sections including wear resistant, head

hardened rails up to 110 UTS, with contractors

tools & plants, equipment, consumable with all

lead & lift etc. complete as directed by Engineer

in-charge. Abrasive Rail Cutter will be as per

RDSO Specification No. TM/SM/1 (Rev. 01 of

2012) with latest status of RDSO; Rail Cutting

Wheel Abrasive Disc will be as per RDSO

Specification No.TM/SM/2 (Rev. 01 of 2020)

Drilling holes of 16 mm to 32 mm dia. with Rail

Drilling machine including chamfering with

appropriate chamfering tools in all types of rail

section with contractor's tools & plants,

equipment, consumable with all lead & lift etc.

complete, as directed by Engineer in-charge. Rail

Drilling Machine will be as per RDSO Specification

No. TM/SM/3, dated 24.04.1991.

5 161050 Drilling holes of specified size for bond holes with Each 48.00 53.93 2588.64

7.2mm dia drill twist to correct spacing and

location on 60kg/52kg rails on cess or under

traffic block with contractor's tools and plant,

equipment, consumable, labour etc complete as

directed by the Engineer in charge at site.

Loading of tongue rail, stock rail, switch assembly

and crossings of any section and length, SEJ,

Glued joint etc. with / without P.Way fittings and

fastenings, in Wagon / Truck / trailer including

lead up to 250 metre and lift up to 5 metre.

6 171024 In Wagon where mechanical handling is possible MT 4.92 161.36 793.89

and traffic block is not required or in Truck/trailer.

Loading, leading and unloading of 52Kg / 60Kg

rail up to 13 metre length by Railway's Rail Dolly /

Dip Lorry to the nominated location under traffic

with line protection in case road carriage is not

possible with different lead with a lift up to 5

metre during block period.

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

Transportation of Rails, sleepers, switches,

crossings, SEJs and Glued Joints by road vehicles

for different leads. Note: 1 . Lead shall be the

shortest motorable road length between the

points of loading and unloading. 2. Loading and

unloading shall be paid extra under relevant

9 172058 Extra for every Km per MT beyond 150 Km over MT-Km 984.00 3.30 3247.20

item no. 172057

Unloading of Switches / Crossings / SEJ Rails /

Glued Joints of any rail section and length with or

w itho ut P.Way fittings & fastenings in neat

manner for Railway usage from departmental

material train (DMT) or contractor's / Railway's

Truck/Trailer with lead up to 250 metre & lift up

Collection, segregation and stacking of various

scattered P.Way materials at nominated stacking

location with serviceable and un-serviceable ones

separately within a lead up to 500 metre and lift

up to 5 metre including crossing of track(s)

wherever necessary as directed by Engineer-in-

11 173031 Rails, switches, crossings, SEJ, Glued Joints, MT 4.92 500.78 2463.84

Check Rails etc.

12 173033 P.Way fittings of all types and other similar loose MT 1.11 430.26 477.59