Renovation of existing Principal bungalow and Extension of administrative office

Amount

Sub Head - A :- Civil Works Earth work

2.34.1 Supplying chemical emulsion in sealed containers including delivery as specified. 2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

2.35.3.1 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor : Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor : 2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

2.6 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. 2.6.1 All kinds of soil

2.10 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 2.10.1.3 Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Concrete

4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 4.1.8 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

5.9 Centering and shuttering including strutting, propping etc. and removal of form for : 5.9.3 Suspended floors, roofs, landings, balconies and access platform

5.9.4 Shelves (Cast in situ)

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers.

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.7 Stairs, (excluding landings) except spiral-staircases.

5.9.16 Edges of slabs and breaks in floors and walls

5.9.19 Weather shades, chajjas, corbels, etc, including edges

5.11 Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. , including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). 5.11.1 Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

5.22A Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto floor V level 5.22A.6 Thermo-Mechanically Treated bars.

5.30 Add or deduct for plaster drip course /groove in plastered surface or moulding to R.C.C. projections.

5.33 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). 5.33.2 All works above plinth level upto floor V level

Brick work

6.4 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand)

6.13 Half brick masonry with F.P.S. bricks of class designation 75 in superstructure above plinth level up to floor V level. 6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand)

6.15 Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry (with F.P.S. bricks).

Stone work

8.2 Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for flooring, staircase treads , riers and landings, kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels. Granite of any colour and shade 8.2.2.1 Area of slab upto 0.50 sqm

8.3 Extra for providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 8.3.2 Granite of any colour and shade

8.4 Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete.

8.6 Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.

8.8 Providing and fixing expansion hold fasterners on C.C./R.C.C. surface backing including drilling necessary holes and the cost of bolt etc complete. 8.8.1.2 Fastener with threaded dia 10 mm.

9.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position : 9.1.1 Second class teak wood

9.21 Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I)non- decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.21.3 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws.

9.46 Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete : 9.46.3 25 mm dia.

9.84 Providing and fixing IS:3564 marked having brand logo with ISI embossed on the plate door weight 36 KG to 80 KG and door width from 701 mm to 1000 mm aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc.complete

9.97 Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 9.97.2 250x10 mm

9.100 Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 9.100.1 125 mm

9.101 Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. 9.101.2 Twin rubber stopper

9.102 Providing and fixing aluminium casement stays ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

9.113 Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles for aluminium door with necessary screws etc. complete ( best make of approved quality)

9.135 Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. 9.135.2 With 12 mm mild steel U beading

9.147D Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealant shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. 9.147D.2 Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

10.1 Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

10.2 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

10.25 Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

10.28 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

11.26 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 11.26.1 25 mm Thick

11.27 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

11.32 Extra for Kota stone/ sand stone in treads of steps and risers using single length up to 1.05 metre .

11.36 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

11.40 Providing and laying rectified ceramic glazed tiles 300 x300 mm or more (thickness to be specified by the manufacture) of 1st quality conforming to IS :15622 of approved make and all colour and shades except white, Ivory, Grey, Fume, Red brown laid on 20mm thick cement morter 1:4 (1cement : 4coarse sand) including pointing the joint with white cement and matching pigments etc. complete

11.41.4 Providing and laying Vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less then 8% and conforming to IS :15622 of approved make and colour and shades laid on 20mm thick cement morter 1:4 (1cement : 4coarse sand) including grouting the joint with white cement and matching pigments etc. complete size of Tile 1000 mmx1000 mm

11.42 Deduct for not using 20 mm thick cement mortar 1:4 ( 1 cement :4 coarse sand) bedding in laying of floor tiles

11.43 Fixing glazed/ ceramic / vitrified floor tiles with cement based high polymer modified quick set tile adhesive ( water based) conforming to IS :15477 using 5 kg adhesive per sqm of tile area in average 3mm thickness

12.41 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 12.41.2 110 mm diameter

12.42 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 12.42.1 Coupler 12.42.1.2 110 mm

12.42.4 Single tee without door 12.42.4.2 110x110x110 mm

12.42.6 Shoe (Plain) 12.42.6.2 110 mm Shoe

12.46 Providing and fixing to the inlet mouth of rain water pipe PTMT (an Engineering Thermoplastic) grating square (Slit) 150 mm square with a height of 8 mm and weighing not less than 100 gms.

12.50 Providing and fixing precoated galvanised iron profile sheets (size, shapeand pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05 %) total coated thickness with zinc coating 120 grams per sqm asper IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12.51 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : 12.51.6 Gutter .(600 mm over all girth)

13.2 15 mm cement plaster on the rough side of single or half brick wall of mix : 13.2.1 1:4 (1 cement: 6 fine sand)

13.16.1 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

13.41 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade 13.41.1 New work (Two or more coats) over and including priming coat with cement primer.

13.44 Finishing walls with water proofing cement paint of required shade : 13.44.1 New work (Two or more coats applied @ 3.84 kg/10 sqm).

13.48 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : 13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr / 10 sqm

13.62 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: 13.62.1 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

13.78 Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete.

15.7 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 15.7.4 In cement mortar

15.17 Dismantling steel work in single sections including dismembering and stacking within 50 metres lead in: 15.17.1 R.S. Joists

15.17.2 Channels, angles, tees and flats

15.18 Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

15.28 Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: 15.28.1 G.S. Sheet

15.58 Demolishing R.C.C. work by mechanical means and stockpiling at designated locations and disposal of dismantled materials up to a lead of 1 kilometre, stacking serviceable and unserviceable material separately including cutting reinforcement bars.

15.60 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

SANITARY INSTALLATIONS

17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 17.28.2 Flexible pipe 17.28.2.1 32 mm dia

17.33 Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40mm long screws, rawl plugs etc. complete.

WATER SUPPLY

18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc., 18.8.2 20 mm nominal outer dia .Pipes.

18.8.3 25 mm nominal outer dia .Pipes.

18.9 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. 18.9.1 15 mm nominal outer dia .Pipes.

18.9.2 20 mm nominal outer dia .Pipes.

18.9.3 25 mm nominal outer dia .Pipes.

18.9.4 32 mm nominal outer dia .Pipes.

18.65 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

18.76 Cutting holes upto 30x30 cm in walls including making good the same : 18.76.1 With common burnt clay F.P.S. (non modular) bricks.

Aluminium work

21.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately) : 21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separately). 21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.2 Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. 21.2.2 Pre-laminated particle board with decorative lamination on both sides .

21.3 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) : 21.3.2 With float glass panes of 5.50 mm thickness

21.13 Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and makinggood etc. complete.

21.15 Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary screws etc. complete 21.15.2 Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.16 Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-charge 21.16.2 Powder coated aluminium (minimum thickness of powder coating 50 micron)

22.5 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry

22.7 Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineerin-Charge : 22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

NS All primary members (Columns & Rafters) would be fabricated from Plates having minimum yield strength of 240/345Mpa. And will conform to ASTM-A-572 Standard. The primary members would be fabricated by continuous shop automated welding using submerged arc welding. Primary members fabricated from plate will have flanges and webs jointed one side alternate on either side of the web by a continuous welding process. All primary members shall have one coat of primer. including all fittings directions of engineer-in-charge

NS The secondary members consist of Z-Purlins and eave struts coated with one coat of primer would be of Cold formed steel having minimum yield strength of 250/320 Mpa and would conform to IS 2062. including all fittings directions of engineer-in-charge

NS Providing and fixing CPVC non- return valve of approved quality 40 mm nominal bore Horizontal

Vertical NS Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length

25mm nominal bore

32 mm nominal bore

NS Providing & Fixing Towel Rack 600 mm long without lower hangers but with three hooks as per direction of Engineer-in-Charge Code : ACN-1181FHN Jaquar

NS Providing & Fixing Soap Dispenser with glass bottel as per direction of Engineer-in-Charge Code: AKP-35735P Jaquar

NS Providing & Fixing Towel Ring Round as per direction of Engineer-in-Charge Code: AQN-7721 Jaquar

NS Providing and fixing CP grating of approved quality as per direction of Engineer-in-Charge.Circular type.100 mm nominal dia.

NS Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes for soil, waste and vent & rain water, Type-B as per IS13592 : suitable for rubber ring joints, including all neccessary specials and fittings (confirming to IS:) i.e. bends, tees, junctions (with or without doors), reducers, couplers, cowls, clamps, rubber rings, clean outs etc. fixing at wall/ ceiling/ floor level supported by clamp & hangers etc. in concealed / inside duct / under floor & basement ceiling / external work etc. including chase cutting,cutting of RCC slab as required, excavation and back filling in all kind of soils, suspended from floor under false ceiling including cost of shuttering for proper completion of the work, breaking and making good the walls and floors etc. after pipes have been duly laid and tested. The Pipes will be supported with threaded G I rods & clamps on 50x50x5 mm slotted angle. The cost will include all support arrangements. The work includes commissioning of all pipes lines as per drawings and specifications and as directed by engg-in-charge at site.-Supreme/Prince make. 110 mm outer dia

NS Providing & fixing Long body Bib Cock with wall flange (Make :- jaguar Con-107 KN )

NS Providing & fixing Angular Stop Cock with nuts, washer with C.P. brass flange complete, including cutting and making good the walls, wherever required. Regular body with adjustable wall flange (Make :- jaguar Con-059 KN )

NS Providing & fixing Concealed Stop Cock with nuts, washer with C.P. brass flange complete, including cutting and making good the walls, wherever required. Regular body with adjustable wall flange (Make :- jaguar Con-089 KN )

NS Providing & fixing Oval counter top Basin with provision also of all accessories required for installation and testing (Brand- Hindware Catalogue no 10017 Oval counter top Basin Star white )

NS Providing & fixing Pillar Cock Long neck With Aerator Hindware

NS Providing & fixing Urinal with provision also of all accessories required for installation and testing (Make :- Hindware catalogue no. 60002 FB- Large standard urinal star white )

NS Providing & fixing 10 Lit. Auto flush Urinal cistern with provision also of all accessories required for installation and testing

NS Providing & fixing Wall-hung European type water closet with provision also of all accessories required for installation and testing (Brand- Hindware Catalogue no 20061 Star white wall mounted closet)

NS Providing & fixing Concealed Cistern with Chrome Plate Brand Viega / Jaquar including testing and all accessories required for installation.

NS Providing and fixing 5.5 mm thk. Mirror mounted on S.S Stud

Sub head B:- Structural Strengthening

NS Scaffolding: Providing and lifting all the material of steel scaffolding and erecting the steel scaffolding on all floors, of the building to attend ceiling repair work, including bracing, cross supports, runner pipes etc., upto any height. Maintaining for period of repairs including dismantling the same and taking away from site plan. Measurement shall be done on basis: height X length (elevation area), for each set of row installed.

NS Micro-Concrete: Providing, mixing and pouring ready to use BASF Masteremaco S346 Micro-concrete mixed with 10mm and down aggregates up to 30% aggregate by weight as per the site requirement & as per specification complete.

NS Shuttering: Providing & fixing and removing water-tight shuttering for pouring micro- concrete in column

NS All charges for providing and applying NITO BOND -FPF on existing surface for all building elements and at all level as per manufacturer specification all complete as per the instruction of Engineer In charge.

134 Providing and applying curing compound FOSROC Concure to the surface on DE shuttering of the column

135 Re-baring: Supplying, Drilling/Cleaning hole and injecting Hilty HY 200 Chemical with the help of Hilti HDM 500 dispenser as per manufacturer/ Structural consultant's specification and fixing rebar of the required diameters subsequently. a 8mm dia - 100mm deep

b 8mm dia - 200mm deep

c 10mm dia - 100mm deep

d 10mm dia - 200mm deep

e 12mm dia - 120mm deep

f 12mm dia - 250mm deep

g 16mm dia - 160mm deep

h 16mm dia - 320mm deep

NS Epoxy Grouting a Drilling and fixing NRV nozzles in RCC members including, Drilling Holes: Drilling 14 mm dia., 50 to 75 mm deep holes in structural members at the intervals of 300 mm c/c horizontally and 200 mm c/c vertically in staggered manner as per the drawing. Cleaning of holes: Clean the holes by air blower prior to fixing nozzles. Fixing of Nozzles: Insert 12 mm dia. NRV nozzles in cleaned holes. Cutting of Nozzles: Cut the nozzles by cut of wheel after completion of grouting without damaging structural elements.

b Applying & filling of shrinkage free low viscous epoxy resin based injection grout. Product: BASF Master inject 1315 (Actual consumption to be recorded at site)

NS Micro Fine Cement Grouting a Supply and installation of G.I packer for injection grouting. Injection packer shall be grouted, and removed post grouting. cost of injection packer

b Additional cost of grouting material Micro fine Cement

NS Providing, mixing and applying polymer modified cement based non shrink pre-packed mortar BASF Master Emaco S 348 in layers of 15mm thickness on chipped concrete. Mortar will be mixed by mechanical stirrer and will be applied by trowel. Each layer to have bond coat which willbe paid separately and each layer of 15mm thick mortar too will be paid separately including curing as per manufacturer’s specification.

NS The damaged concrete patch shall be repaired with polymer modified mortar of structural grade having mix design as 50 kg cement: 200 kg coarse sand: 5 kg Sika Latex (Product Data Sheet enclosed), and water to have workable consistency. PMM shall be applied in multiple layers of not more than 15 mm thickness in one layer in the maximum of 40 mm.

NS Identifying loose hollow, cracked concrete. Chiseling off the same carefully by manual method, upto good non- carbonated concrete. Lowering, stacking the debris.A) Brushing cleaning the exposed reinforcement. Hacking loose, delaminated concrete, loose aggregates from the surface of tor steel bar. Providing and applying rust converter chemical Sika rust off 100 or equivalent. Washing cleaning and re- brushing the steel after 12 hours minimum. Surface area of steel reinforcement will be measured for payment.B) Providing and applying Zinc rich primer BASF Master Emaco p-130 / Sika Fria Zinc, of approved make to the exposed, cleaned reinforcement. Surface area of steel reinforcement shall be measured for payments.

NS Spray concrete with BASF-810 upto 50-60 mm thickness

NS Providing & applying 12mm to 15mm average thick Cement Sand Plaster with Polypropylene Fiber to internal walls in superstructure above plinth level up to any height & level in cement mortar 1:6 (1 cement: 6 coarse sand) including hacking the surfaces, scaffolding, curing, making grooves at desired locations & curing etc. all complete as per details, specifications, drawings and to the satisfaction of the Engineer.

NS Providing, fabricating and erecting Structural steel members in position at all levels and at all heights as specified in the drawings made out of standard MS sections solid/ hollow conforming to IS 226/2062/800. Cost to include fabricating necessary Gusset Plates, Stiffener plates, Brackets, Bolts, Cleats, seating angles etc., to the required size, shape, alignment etc., as per the drawings. Cost to include welding of members using structural steel welding electrodes as per IS 814 / 816 / 817, a coat of anti-corrosive primer (nonflammable) to the exposed surfaces, testing as per IS 7307 (PART 1), necessary equipment's, wastage, tools and tackles, staging, scaffolding required etc., complete including a coat of zinc chromate primer and two coats of Synthetic enamel painting.

NS Providing & applying Welded Wire Mesh to internal walls or RCC surfaces in superstructure above plinth level up to any height & level including scaffolding and Power driven Nails etc. all complete as per details, specifications, drawings and to the satisfaction of the Engineer.

NS Providing, fabricating, erecting MS frame work comprising of sections like angle and tube for sun shade.

NS Diamond sawing in brick work upto 230mm for creating openings/ creating slots for resting of reinforcement.

NS Diamond sawing in RCC member for creating cutouts/ breaches, pockets etc. for passing of service lines or complete removal of member. a For RCC slab

b For RCC column & beams

NS Supply and fixing anchors as per specification: a HILTI HST M-12 Mechanical Anchor

b HILTI HST M-16 Mechanical Anchor

c HILTI HVA M-12 Chemical Anchor

d HILTI HVA M-16 Chemical Anchor

e HRD M-10 X 100 Mechanical Anchor for Frame Fixing

f HLC M-10 X 80 Mechanical Anchor For Frame Fixing

NS Plinth protection: Providing & Laying of RCC around all periphery of building upto thickness of 75-125 with a widthof 1 meter to protect foundation from waterlogging

Carbon wrapping NS Chipping of bulged beams, columns etc. to required plane and making good the surface including removing of malba outsider depot.

NS Surface Preparation: Grinding of surface of columns to perfect level and rounding of edges by around 25 mm including filling of any honeycombing/patches in surface by high strength epoxy compound (Sikadur 31/ BASF- Master Brace 2200)

NS 430 GSM Single layer: Supply and Installation of unidirectional carbon fiber wrap of minimum 430 GSM (SIKAWRAP /BASF Master Brace GSM 430) bonded with special grade epoxy adhesive (BASF <Asterbrace4500 )applied @ consumption co- efficient of 0.8-1.2 Kg/sqm on 1st layer and there-after 0.7 kg/sqm for subsequently layer as per the manufacturer design and specification. The thickness of Carbon wrap shall be minimum 0.25 mm. The complete system shall consist of sprinkling of coarse sand over and above final top coat of epoxy adhesive for making suitable for plaster. Column surface area to be measured for payment

NS Providing and applying 40 mm thick cement sand plaster above the carbon wrapping of treatment in cement mortar 1:6 (1 cement : 6 fine and coarse sand I equal proportions) finished smooth including hacking the surfaces, scaffolding, curing, making grooves at desired location etc. complete as per drawing.

NS Providing and applying one coat of curing compound on finished surface

Sub head C:- Electrical works

1.1 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc. as required. 1.1.3 Group C

1.11 Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit, 2 way modular switch,modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required

1.17 Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required 1.17.3 3 x 1.5 sq.mm

1.17.6 6 x 1.5 sq.mm

1.17.9 9 x 1.5 sq.mm

1.17.12 3 x 2.5 sq.mm

1.17.15 6 x 2.5 sq.mm

1.17.21 3 x 4 sq.mm

1.17.24 6 x 4 sq.mm

1.17.30 3 x 6 sq.mm

1.18 Supplying and drawing following pair, 0.5 sq.mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface/ recessed steel/ PVC conduit as required 1.18.2 2 Pair

1.21 Supplying and fixing of following sizes of medium classPVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 1.21.1 20mm

1.24 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 1.24.5 6 pin 15/16 amp socket outlet

1.24.6 Telephone socket outlet

1.24.7 TV antenna socket outlet

1.24.8 Bell Push

1.25 Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required

1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

1.27 Supplying and fixing following size/ modules, GI box along with modular bases & cover plate for modular switches in recess etc as required 1.27.1 1 or 2 Module (75mm X 75mm)

1.27.4 6 Module (200mm X 75mm)

1.27.5 8 Module (125 mmX125 mm)

1.27.6 12 Module (200 mmX150 mm)

1.33 Supplying and fixng 3 pin, 5 amp. Ceiling rose on the existing junction box/ wooden bolock including connection etc. as required.

1.44 Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable etc. as required.

1.50.1 Installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as required.( Up to 450mm sweep)

1.51 Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

2.3 Supplying and fixing follwing way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). 2.3.8 2+12 way, Double door

2.8 Supplying and fixing following way, prewired, TP&N MCB distribution board, of steel sheet for 415 volts, on surface/ recess, complete with loose wire box, terminal connectors for all incoming and outgoing circuit, duly prewired with suitable size FR PVC insulated copper conductor up to terninal bocks, tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnection, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator). 2.8.8 12 Way (4+36) Double Door

2.1 Supplying and fixing 5 amps ot 32 amps rating, 240 volts, 'B' series, miniature circuit breaker suitable for lighting and other load of following poles in the exisiting MCB DB complete with connections, testing and commissioning etc. as required. 2.10.1 Single pole

2.12 Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.12.1 40 amps

2.13 Supplying and fixing following rating, four pole,415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.13.2 63 amps

4.1 Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 4.1.4 300 mm width X 50 mm depth X 1.6 mm thickness

4.1.7 600 mm width X 50 mm depth X 2.0 mm thickness

5.2 Earthing with G.I. earth pipe 4.5 mtr long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with without charcoal/coke and salt as required.

5.11 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.pipe from earth electrode including connection with G.I. nut, bolt,spring, washer excavation and re-filling etc. as required.

5.14 Providing and fixing 25 mm X 5 mm G.I. Strip on surface or in recess for connection etc at reqd.

5.16 Providing and and fixing 6 SWG dia G.I wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring / cable as required.

7.1 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. 7.1.1 Upto 35 sq. mm

7.7 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. 7.7.1 Upto 35 sq. mm (clamped with 1mm thick saddle)

9.1 Supply and making end termination with brass compression gland and aluminium/copper lugs for following size of PVC insulated and PVC sheated/XLPE aluminium/copper conductor cable of 1.1KV grade as required. 9.1.34 4C x 25 Sq.mm Aluminium armoured

9.1.35 4C x 35 Sq.mm Aluminium armoured

9.1.22 3.5C x 50 Sq.mm Aluminium armoured

9.1.23 3.5C x 70 Sq.mm Aluminium armoured

9.1.27 3.5C x 185 Sq.mm Aluminium armoured

NS Supplying of following sizes PVC insulated and PVC sheathed power cable of 1.1 KV grade armouret L.T cable as required conforming to IS:1554/IS-7098 ( Part-I ) 1998 as reqd at site. a) 4C x 25 Sq.mm Aluminium armoured

b) 4C x 35 Sq.mm Aluminium armoured

NS Supply and fixing modular type A/C box complete with 16amp socket outlet 6 to 32 amp SPMCB, cover plate,connection testing and fixing etc as reqd

NS Supply and fixing suitable size G.I. box with modular plate & connection in front on surface or in recess, including providing & fixing 3 nos. 6 pin, 15/16 amp. Socket outlet & 1 no. 15/16 Amp. Modular switches, 1 no. indicator, connection, painteing etc. complete as reqd.

NS Fabrication,Supplying,testing, installation and commissioning of well/ floor mounted cubical panel board/feeder piller duly made out of 2 mm thick (M.S) fully compartmentalized having 200 amps.4 strip aluminium bus bar,interconnection earthing etc. complete as reqd.(Up to 350mm deep)

NS Supply and fixing of 18 W LED surface panel MOD light with 18 W LED bulb ( Brand Halonix)

NS Supply and fixing Havells brand LED PRIDE PLUS NEO BATTEN 20 W 3000 K Warm Daylight LHEXACP5IN1W020 Decorative Slim Linear LED Batten Length : 1.15 m (1150 mm) Polycarbonate Body, SquareProfile

NS SUPPLY AND FIXING REGAL BATTEN LED Upto 2x22 W LED Tube (Single Side Connection), General purpose industrial compact batten suitable for single or twin Endura Tube Light with 1m. drop from ceiling

NS Supply of BULKHEAD Luminaire with toughened frosted glass suitable for 1 no 9 watt CFL lamp complete as required. ( Philips make ) cat no FXC 101

NS Supply of following size of A.C. exhaust fan Size of 300 mm,900RPM single phase heavy duty complete with motor, blade fan and cover complete accessories in all respect.(Make:- Khaitan/Bajaj/Usha)

NS Supply of 1200mm sweep A.C electric ceiling fan,capicitor type double ball bearing complete with 300mm down rod. Canopies,shackles,blades,but without regulator suitable for operation on 230/240 volts,50Hz,single phase,A.C.supply etc as reqd. (Make-:Bajaj/Usha/Khaitan)

NS Supply and fixing of Single port British Style faceplate white (with box) complete in all respect at site.

NS Supply and fixing of Giga,24 port Jack Panel (Cat-6) complete in all respect at site.

NS Supply and fixing of Mounting Cord 7 ft Cat 6 complete in all respect at site.

NS Supply and fixing of Mounting Cord 4 ft Cat 6 complete in all respect at site.

NS Supply and fixing of 48 port managed switch gigabit SG300 complete in all respect at site.

NS Supply and fixing of 42U floor standing rack with 230 volt AC fan-4d cable manager-9 12 port PDU,HW-5Pkt,Castor Set complete in all respect at site.

SUB-HEAD D:AIR CONDITIONER WORK.

NS Supplying, installation, testing & commissioning of Aircooled Split Air-conditioners each comprising an outdoor unit consisting of Rotary Compressor, Condensor fan,etc. with outer casing and indoor Hi-wall Type 1.5 TR unit consisting of blower, filter, motoretc. having specified CFM 230+/_10% ,1-50 Hz alongwith cordless remote, (R-22) 1.5 TR with BEE 4 star rating.

NS Supplying, installation, testing & commissioning of Aircooled ceiling concealed Air-conditioners each comprising an outdoor unit consisting of Rotary Compressor, Condensor fan,etc. with outer casing and indoor ceiling concealed type 2.0 TR unit consisting of blower, filter, motoretc. having specified CFM 630+/_10% ,1-50 Hz alongwith cordless remote, (R-22 refrigerant) 2.0 TR with BEE 4 star rating.

NS Installation charges for 1.5 TR Hi-wall type Airconditioner

NS installation charges for 2.0 TR Ceiling concealed type Airconditioner

NS Soft Copper Pipe 1/2"& 1/4" having thickness of .8 mm for 1.5 TR AC units

MR Soft Copper Pipe 1/2"& 3/4" having thickness of 1.0 mm for 2.0 TR AC units

NS 4 c (1.5mm) electrical wiring from indoor to outdoor unit (BIS)

NS 3 c (2.5 sqmm) Electrical wiring from MCB to outdoor units (BIS)

NS 6 sq mm Electrical wiring from MCB to outdoor units as / BIS

NS 25 mm Dia. Hard PVC drain pipe

NS Voltage stabilizers 4 KVA for A/C

NS M.S. angle stand for outdoor units

Sub Head E:-FIRE FIGHTING SYSTEM

Fire Extinguishers a) ABC type multipurpose fire extinguishers cap-4kg ISI marked 15683 along with certificates

b) CO2 type fire extinguishers cap 4.5 kg use on B&C class

NS Providing and fixing signages printed on photoluminescent U1000 aluminium sheet of 1.0 mm (+ -10%) containing lumigen II as base chemical, covered under UV stablized coating and of appropriate size (Glo-lite or eq. Make) including fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats anchor fasteners etc. complete in all respacts as diercted by Engineer-in-charge.

Any item not covered in BOQ

Any item not covered in BOQ and needs to be executed as per actual site condition, shall be paid as per DSR 2016 . ( please quote percentage above or below DSR 2016)

Baljeet Builders and Interior Decorators

NORTH STAR CONSTRUCTIONS