Loading…
Loading…
Tender Value
₹5.3 Cr
EMD Value
₹10.7 L
Closing Date
15 Sept 2026, 3:00 pm
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
WORKS
17 conditions · 6 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments'' in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited,the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The tenderer shall submit along with the tender document, documents in support of his/their claim to fulfill the eligibility criteria as mentioned in the tender document. Each page of the copy of documents/Certificates in support of credentials, submitted by the tenderer, shall be self- attested/digitally signed by the tenderer or authorized representative of the tendering firm. Self- attestation shall included signature, stamp and date ( on Each page).
The tenderer must have successfully completed or substantiallycompleted any one of the following categories of work(s) during last 07(seven) years, ending last day of month previous to the one in whichtender is invited: Three similar works each costing not less than theamount equal to 30% of advertised value of the tender, or Two similarworks each costing not less than the amount equal to 40% of advertisedvalue of the tender, or One similar work each costing not less than theamount equal to 60% of advertised value of the tender. NOTE-(i) SimilarWork means " (i) Indoor work involving supply, installation, testing &commissioning of Electronic Interlocking/RRI/PI (OR) (ii) Both Indoor andOutdoor works involving supply, installation, testing & commissioning ofElectronic Interlocking/RRI/PI ( O R ) (iii) Intermediate BlockSignaling/Automatic Block Signaling/Provision or replacement of any typeof block instruments/LC Gate Interlocking work/ Yard Remodeling workinvolving installation or alteration to Electronic Interlocking/RRI/PI (OR)(iv) MACLS outdoor signaling work which includes one or more works likecable trenching & laying/location erection and wiring/point machineinstallation or replacement (including power operated siding points)/signal foundation and erection/track circuiting /double distant/BPACinstallation/Axle Counter installation.NOTE : If the works involves installation and/or alteration of El System then following conditions shall be satisfied : (i) The successful bidder shall submit an undertaking from same RDSO approved El OEM before the supply of material to confirm compliance with extant RDSO guidelines and to meet contract specific requirements" (ii)Certificate as mentioned videabove eligibility criteria issued by Private firm/ company/individual willnot be accepted. NOTE :- Work experience certificate from privateindividual shall not be considered. However, in addition to workexperience certificates issued by any Govt. Organisation, workexperience certificate issued by Public listed company having averageannual turnover of Rs 500 crore and above in last 3 financial yearsexcluding the current financial year, listed on National Stock Exchange orBombay Stock Exchange, incorporated/registered at least 5 years prior tothe date of opening of tender, shall also be considered provided the workexperience certificate has been issued by a person authorized by thePublic listed company to issue such certificates. In case tenderer submitswork experience certificate issued by public listed company, the tenderershall also submit along with work experience certificate, the relevantcopy of work order, bill of quantities, bill wise details of payment receivedduly certified by Chartered Accountant, TDS certificates for all paymentsreceived and copy of final/last bill paid by company in support of abovework experience certificate.
The tenderer shall submit along with the tender document, documents in support of his/their claim to fulfill the eligibility criteria as mentioned in the tender document. Each page of the copy of documents/Certificates in support of credentials, submitted by the tenderer, shall be self- attested/digitally signed by the tenderer or authorized representative of the tendering firm. Self- attestation shall included signature, stamp and date ( on Each page).
The tenderer shall submit a certificate stating that they are not liable to be disqualified and all their statements/documents submitted along with bid are true and factual. Standard format of the certificate to be submitted by the bidder is enclosed as annexure-V and VA. Non submission of an certificate by the bidder shall result in rejection of his/their bid. And it shall be mandatorily incumbent upon the tenderer to identify, state and submit the supporting documents duly self attested by which they/he is qualifying the qualifying criteria mentioned in the tender document. It will not be obligatory on the part of Tender committee to scrutinize beyond the submitted document of tenderer as far as his qualification for the tender is concerned . In case of partnership firm the Annexure VA shall be submitted by by each partner separately/individually failing which the offer will be summarily rejected.
The Tenderer should submit all the relevant documents required as per GCC-2022 to ascertain the eligibility status of the firm as per Para 10 to 19 of Annexure-I GCC-2022.
100 conditions · 2 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The rates are inclusive of Tax (GST)/all charges and all the taxes/duties leviable by the Central Government / State Government/Local Authorities etc. as applicable.
Tenders containing erasures and/or alterations of the tender documents are liable to be rejected. Any corrections made by the Tenderer (S) in his/their entries must be attested by him/them.
Rights of the Railway to deal with tender: The authority for the acceptance of the tender will rest with the Railway. It shall not be obligatory on the said authority to accept the lowest tender or any other tender and no tender(s) shall demand any explanation for the cause of rejection of his/their tender nor the Railway undertake to assign reasons for declining to consider or reject any particular tender or tenders.
If the tenderer(s) deliberately gives / give wrong information in his/their tender or creates/create circumstances for the acceptance of his/their tender, the Railway reserves the right to reject such tender at any stage.
If the tenderer(s) expires after the submission of his/their tender or after the acceptance of his/their tender, the Railway shall deem such tender cancelled. If a partner of a firm expires after the submission of their tender or after acceptance of their tender, the Railway shall deem such tender as cancelled, unless the firm retains its character.
All general and detailed drawing's pertaining to this work, which will be issued by the Engineer or his representatives (from time to time) with all changes and modifications.
Drawings for the work: - The drawings for the work can be seen in the office of the Senior Divisional/Divisional/District/Deputy Chief / Executive Engineer and / or Chief Engineer/Chief administrative officer (Construction) Railway at any time during the office hours. The drawings are only for the guidance of tenderer(s). Detailed working drawings (If required) based generally on the drawing mentioned above will be given by the Engineer or his representative from time to time.
Tenderer s Credentials: - Documents testifying tenderer s previous experience and financial status should be produced along with the tender or when desired by the competent authority of the South East Central Railway. Tenderer(s) who has / have not carried out any work so far on this Railway and who is/are not borne on the approved list of the contractors of South East Central Railway should submit along with his/their tender credentials to establish. i. His capacity to carryout the works satisfactorily. ii. His financial status supported by Bank reference and other documents. iii. Certificates duly attested and testimonials regarding contracting experience for the type of job for which tender is invited with list of works carried out in the past.
Non compliance with any of the conditions set forth there in above is liable to result in the tender being rejected.
Execution of contract documents:- The successful tenderer(s) shall be required to execute an agreement with the president of India acting through the South East Central Railway for carrying out the work according to Standard General condition of contract, Special conditions/specifications. annexed to the tender and specifications for work and materials of Railway as amended/corrected upto latest correction slips, mentioned in tender form (first sheet).
Partnership deeds, power of attorney etc.:-The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm /Company / Joint Venture (JV) / Registered Society /Registered Trust / HUF etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm,company, association, trust or society, as the case may be as item No.14 Part 01 of GCC-2022.
The tenderer whether sole proprietor, a company or a partnership firm/Joint venture (JV)/registered Society/registered trust etc. if they want to act through agent or individual partner (s) should submit along with the tender, apower of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person specifically authorizing him/them to submit the tender, sign the agreement, receive money, witness measurements, sign measurement books, compromise, settle, relinquish any claim(s) preferred by the firm and sign No claim Certificate and refer all or any disputes to arbitration
Should a tenderer or contractor being an individual on the list of approved contractors, have a relative(s) or in the case of partnership firm / company/ joint venture(JV)/registered society/registered trust etc. one or more of his shareholder(s)or a relative(s) of the shareholders employed in Gazettedcapacity in the Engineering or any other Department of the South East Central Railway, the authority inviting tenders shall be informed of the fact, at the time of submission of tender,failing which the tender may be disqualified/ rejected or if such fact subsequently comes to light, the contract may be rescinded in accordance with the provision of clause 62 of the Standard General Conditions of Contract.
The contactor shall also employ qualified Graduate Engineer or qualified Diploma Engineer, based on value of contract, as may be prescribed by the Minister of Railways through separate instructions from time to time. As per GCC Clause 26A.
Railway reserves the right to draft the vehicles and equipment of contractor in case of accidents/natural calamities involving human lives. For this, separate payment shall be admissible through introduction of NS item as per of GCC, and the rates decided by the railway of this purpose shall be final and binding on the contractor and shall be an excepted mater and hence shall remain excluded from the preview of the arbitration clause of the agreement.
While executing the work along the Railway track/any other location in the vicinity of under ground signaling/Electrical/Telecom/OFC cables, the contractor s shall take all precautions to safe guard the cables. A penalty will be imposed as below, if the contractor damages any of these cables even after being advised in writing before start of the work to take adequate precaution to protect these cables. (In terms of Railway Board s letter No.2003/Tele/RCIL/1/Pt. IX dtd:24.06.2013) Cable damaged Penalty per location Only Quad cable or Signalling Cable Rs.1.0 Lakh Only OFC Rs.1.25 Lakh Both OFC & Quad Rs.1.5 Lakh Electrical Cable Rs.1.0 Lakh
Joint Procedure Order No.SECR/S&T/Policy/889, dated 05.07.2012 for undertaking earh work in the vicinity of cables issued by CSE/SECR/BSP vide letter No.SECR/S&T/Policy/959, dated 16.07.2012 , C.E s cirlular No.16 for safety precautions at work-site in proximity of running lines issued by C.E./SECR/BSP vide letter No.ENGG/TC-2/C.E.Circular/442, dated 16.06.2006 and C.E s cirlular No.31 for quality control at work sites and maintenance of registers issued by C.E./SECR/BSP vide letter No.Engg/Plg./76/CE s Circular@47"44@ dated 18.08.2011 will be applicable and binding to the contractor.
Price Variation Clause (PVC):Price variation clause is not applicable for this tender.
Earnest money:-
(a)The tender must be accompanied by desired sum (as mentioned in NIT) as earnest money in favour of F.A.& C.A.O.S.E.C.Railway Bilaspur , deposited through internet banking,Credit /debit card failing which the tender will not beconsidered. Any firm recognized by Department of Industrial Policy and Promotion (DIPP) as 'Startups' shall be exempted from payment of Earnest Money on submission of Registration Certificate issued by appropriate authority.
(b) The Tenderer(s) shall keep the offer open for a minimum period of 60 days (in case of two packet system of tendering 90 days) from the date of opening of the Tender. It is understood that the tender documents have been issued to the Tenderer(s) and the Tenderer(s), is / are permitted to tender in consideration of the stipulation on his / their part that after submitting his / their tender subject to the period being extended further, if required by mutual agreement from time to time, he will not resile from his offer or modify the terms and conditions thereof in a manner not acceptable to South East Central Railway. Should the tenderer fail to observe or comply with the foregoing stipulation, the amount deposited as Earnest Money for the due performance of the above stipulation, shall be forfeited to the Railway.
(c) If his tender is accepted the earnest money mentioned in sub clause (a) above will be retained as part security for the due and faithful fulfillment of the contract in terms of Clause 16 (1) of the Standard General Conditions of Contract. The Earnest Money of other Tenderers shall, save as herein before provided, be returned to them, but the Railway shall not be responsible for any loss or depreciation to the Earnest Money that may happen thereto while in their possession, nor be liable to pay interest thereon.
The earnest money of the unsuccessful tenderer(s) will, save as herein- before provided be returned to the unsuccessful tenderer(s) within a reasonable time but the Railway shall not be responsible for any loss or depreciation that may happen to the security for the due performance of the stipulation to keep the offer open for the period specified in the tender documents or to the Earnest money while in their possession nor be liable to pay interest thereon.
The successful bidder shall have to submit a Performance Guarantee (PG) within 21 (Twenty one) days from the date of issue of Letter of Acceptance(LOA). Extension of time for submission of PG beyond 21 (Twenty one) days and upto 60days from the date of issue of LOA may be given by the Authority who is competent to sign the contract agreement. However, a penal interest of 12% per annum shall be charged for the delay beyond21(Twenty one) days, i.e. from 22nd day after the date of issue of LOA. Further, if the 60th day happens to be a declared holiday in the concerned office of the Railway, submission of PG can be accepted on the next working day. In all other cases, if the contractor fails to submit the requisite PG even after 60 days from the date of issue of LOA, the contract is liable to be terminated. In case contract is terminated railway shall be entitled to forfeit Earnest Money Deposit and other dues payable against that contract. Incase a tenderer has not submitted Earnest Money Deposit on the strength of their registration as a Startup recognized by Department of Industrial Policy and Promotion (DIPP) under Ministry of Commerce and Industry, DIPP shall be informed to this effect. The failed Contractor shall be debarred from participating in re-tender for that work.Performance guarantee shall be initially valid upto the stipulated date of completion plus 60 days beyond that. In case, the time for completion of work gets extended, the contractor shall get the validity of PG extended to cover such extended time for completion of work plus 60 days. The value of PG to be submitted by the contractor will not change for variation upto 25% (either increase or decrease) In case during the course of execution, value of the contract increases by more than 25% of the original contract value, an additional Performance Guarantee amounting as per GCC for the excess value over the original contract value shall be deposited by the contractor. Performance Guarantee shall be released after the physical completion of the work based on the completion certificate issued by the competent authority stating that the contractor has completed the work in all respect satisfactorily. As per Advance Correction Slip No. 11 of GCC-2022, If the tender is accepted on the quoted rates of bidder which is more than 5% below the advertised tender value, an additional performance security shall be submitted by the bidder equal to 5% of the accepted value of the tender. The total performance guarantee in this case will be 10% of the accepted value of the tender.
Tenderer must submit the following documentary evidence in proof of their: -
List of Personnel Organization available on hand and proposed to be engaged for the subject work.
List of Plants and Machinery available on hand (own) and proposed to be inducted (own and hire, to be given separately for the subject work).
List of works completed Governemtn/Semi-Government (fully owned by Govt.) departments in the last Seven financial years giving description of work. Organization for whom executed, approximate value of contract at the time of award, date of award and date of schedule completion and final value of contract should also be given.
List of work on hand indicating description of work, contract value, approximate value of balance work yet to be done.
Deed of Partnership special power of attorney, if any for the work.
Joint venture/MOU/Consortium shall not be accepted.
All the payment will be made through electronic funds transfer only through any of the nationalized/scheduled bank. For this the proforma collect from this office before made first bill and is to be essentially filled up by the tenderer and submit the same to accounts department for releasing the payment.
As per Indian Railways Standard General Conditions Of Contract para 6 (a), proper survey must be done by the tenderer before submission of tender.
In case any contradiction between general condition of contract & special conditions of contract, special conditions of contract will prevail over general conditions of contract.
The Railway reserve the right to verify all statements, information and documents submitted by the bidder in his tender offer, and the bidder shall, when so required by the Railway, make available all such information, evidence and documents as may be necessary for such verification. Any such verification or lack of such verification, by the railway shall not relieve the bidder of its obligations or liabilities hereunder not will it affect any rights of the railway thereunder.
In case of any wrong information submitted by tenderer, the contract shall be terminated, Earnest money Deposit ( EMD), Performance Guarantee ( PG and Security Deposit ( SD) of contract forfeited and agency barred for doing business on entire Indian Railways for 5 ( five) years.
Tenderers will examine the various provisions of the Central Goods and Services Tax Act, 2017 (CGST)/Integrated Goods and Services Tax Act, 2017 (IGST) Union Territory Goods and Services Tax Act, 2017 (UTGST)/respective states State Goods and Services Tax Act (SGST) also, as notified by Central/State Govt. & as amended from time to time and applicable taxes before bidding Tenderers will ensures that full benefit of Input Tax Credit (ITC) likely to be availed by them is duly considered while quoting rates.
The successful tenderer who is liable to be registered under CGST/IGST/UTGST/SGST Act shall submit GSTIN along with other details required under CGST/IGST/UTGST/SGST Act torailway immediately after the award of contract, without which no payment shall be released to the contractor. The contractor shall be responsible for deposition of applicable GST to the concerned authority.
In case the successful tenderer is not liable to be registered under CGST/IGST/UTGST/SGST Act, the railway shall deduct the applicable GST from his/their bills under reverse charge mechanism (RCM) and deposit the same to the concerned authority.
S&T Work in connection with:(1) Construction of long haul loop in Up grid by extending DE of ORL of Up loop L/No.-1 at KTE end with dispatch facility and connecting banking engine siding to Up loop L/No.-1 at BSP end at KGS station of Bilaspur Division.(2) Chhulha: Construction of Long Loop Line (CAL-750m, DS- PT) with bi-directional 03rd line by extending DE of loop line No.-5 at APR end.
15-ST-Tender-2026~SECR
15-ST-Tender-2026
Open
Works - General
9 Months
Bilaspur, Chhattisgarh
₹0
₹10.7 L
19 Aug 2026
19 Aug 2026
1 Sept 2026
234 items across 8 schedules · ₹5,34,12,835.29 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Excavation of trench and clearing of roots of trees, bushes, ballast and reconditioning etc., including bailing out water and disposal of extra soil.(i) all soils including soft rocky area. Depth 1.0 Mtr. & width 0.3 Mtr. | Kilometre | 12.00 | 76,590 | 9,19,080 |
| 2 | Laying of Signalling Cable/Power/Quad cable / PIJF cable in the excavated trench to Drg.No:CON/SK/T/5.Transportation, supply of 'U' clamps and anchoring of cable at every 10 Mtrs with 'U' clamp to Drg.No:CSTE/C/Cable/81 including back filling with excavated earth and ramming of trenches after cable laying. Inspection by the Rep. of Sr.DSTE/Co./BSP. | Kilometre | 121.00 | 16,740 | 20,25,540 |
| 3 | Excavation of trench and clearing of roots of trees, bushes, ballast and reconditioning etc., including bailing out water and disposal of extra soil. Hard rocky area including concreting. Chase cutting and smoothening of inside surface of sizes 0.08 m deep and 0.17 m width at platform and cemented floor area. | Metre | 500.00 | 115 | 57,500 |
| 4 | Trenching in hard rocky area using chiselling up to a depth of 0.7mtr & 0.3mtr. Wide at bottom & concreting. | Metre | 550.00 | 152 | 83,600 |
| 5 | Excavation of trench and clearing of roots of trees, bushes, ballast and reconditioning etc., including bailing out water and disposal of extra soil. Hard rocky area including concreting. Cutting the masonary wall to the depth of 0.25m to 0.75m at the entry of room placing of flexible HDPE pipe or G.I.Pipe (including supply) of suitable size as per drawing No. RE/S&T/ALD/SK/161/81. | Numbers | 8.00 | 582 | 4,656 |
| 6 | Laying of second class bricks including supply of required quantity at site on single/multiple cable laid in the trench (Approx 9 bricks per mtr). Inspection by the Rep. of Sr.DSTE/Co./BSP | Kilometre | 2.00 | 32,603 | 65,206 |
| 7 | Laying of half round RCC hume pipe with 150 mm dia & 1 mtr long including supply at site on single/multiple cable laid in the trench. Inspection by the Rep. of Sr.DSTE/Co./BSP. | Metre | 600.00 | 254 | 1,52,400 |
| 8 | Laying of RCC pipe including supply of required quantity at site with collars (for jointing pipe) 150 mm nominal dia to Spec.No:IS-458 in excavated trench and laying of Signalling/ Power cable/PIJF cable/ Quad cables/HDPE pipe through RCC pipe. Power cable shall be laid in the same trench alongwith signalling/Quad cables but in a separate pipe RCC pipe at track/pucca road/ Platform crossing/ level crossing gate etc. The work is to executed as per the instruction of Railway site Engineer. | Metre | 230.00 | 775 | 1,78,250 |
| 9 | Transportation, loading/unloading of OFC from the stores of railway to the work site with care, pushing/pulling OFC through the HDPE pipes, sealing of the duct by sealling /caps plugs. The cable is to be laid by mechanised means. At inaccessible places where mechanised laying is not possible, the cable is to be laid manually by pulling through pre inserted rope. This also includes testing of cable drums in the store premises before transportation and submissions of results thereof. Empty cable drums to be returned by the contractor. The cable drums with unused cable at site to be returned by the contractor to the stores depot of consignee. | Kilometre | 2.50 | 18,672 | 46,680 |
| 10 | Transportation including loading/unloading of HDPE pipe from the stores of railway to the work site, laying of the same (with 4 mm nylon rope pre-inserted inside the HDPE pipe) in excavated trench/already laid GI/RCC pipes/tubes, jointing, levelling and end sealing the pipes. | Kilometre | 2.00 | 7,762 | 15,524 |
| 11 | Transportation/Shifting of cables in roll with or without wooden drums from other than nominated consignee depot and meggering before loading and after laying, and recording the values in cable insulation register along with representative of Railways. | Numbers | 150.00 | 1,282 | 1,92,300 |
| 12 | Transportation, installation of optical fibre joint closure and splicing of Optical fibre cable (2 x 24 fibres) and testing, Optical fibre cable splicing shall be done in the presence of Railway's representative. Only joint closure shall issued by the Railway. All other tools/test equipments required shall be arranged by the Contractor. This also includes excavation of earth for construction of masonary pit of bricks (inside complete plastered), the inner size of pit 1.2m x 1.2m (depth 0.75m) in all types of soils for keeping cable coils at the location of OFC joints, filling the pit with sand after jointing of cables, ramming and covering with RCC slab as per Drg. and instructions of site incharge of Railway. | Numbers | 6.00 | 19,019.96 | 1,14,119.76 |
| 13 | Transportation, Charging and installation of secondary cell 2 V (lead acid type), and preparation of electrolyte for lead acid cells. If power is not available at site of work, charging may be done at nearby location as per convenience of the Railway. Initial Charging to be done in presence of Rlys representative from executive agency as well as maintenance org, with uninterrupted supply. 80AH | Numbers | 48.00 | 310 | 14,880 |
| 14 | Transportation & Execution of following kinds of joints on Quad Cable using thermo shrink jointing kit. This also includes excavation of cable joint pit of size 1.2m x 1.2m x 1.0m in all types of soil for jointing of copper cables, back filling and ramming after jointing. straight through joint on Quad cable/10-20- 50 pairs PIJF Cable | Numbers | 10.00 | 1,385 | 13,850 |
| 15 | Track crossing, Road Crossing by pushing method (HDD method) at culverts/ track / pucca road crossing at a depth not less than 1 meter with reference to bottom of rail/road surface including supply of GI pipe . GI pipe with 76 mm dia, Spec. No. -1239 medium grade (for the length of pushing more than 05 meters).inspection by the Rep. of Sr.DSTE/Co./BSP. | Metre | 550.00 | 2,246 | 12,35,300 |
| 16 | Cement Concrete of proportion 1:3:6 with graded aggregate of size 25mm. and below. | cum | 40.00 | 2,943 | 1,17,720 |
| 17 | Laying and Fixing of galvanised iron pipe (GI Pipe) with threaded collars (for jointing pipe) of 80 mm nominal dia Spec.No.IS-1239 medium grade, on bridges, culverts, drains including supply and transportation of GI pipes and all other materials required for fixing the pipe to Drg.No.Con/SK/T/2 and drawing of Signal/Power/Quad cables inside the pipe with masonary works over the entire length of the bridge and at entry and exit of the culvert and curing for 72 hrs, drilling of holes on the pipe at 10 cm apart to be clamped 2 Mtrs apart on culvert, for the Signalling, quad, power cable. inspection by the Rep. of Sr.DSTE/Co./BSP. | Metre | 340.00 | 761 | 2,58,740 |
| 18 | The excavation of pit, casting of concrete foundation including surrounding earthwork along the foundation, erection, installation and wiring of steel apparatus case, fixing of terminals, fuse blocks, signal transformer, current transformer, filament switching unit, track battery chargers, adjustable/fixed resistances, choke coils, Fuses, Relays, E type locks, termination of cables, cable insertion, wiring to draw 110V AC therefore in the new apparatus case as required, testing, commissioning including subsequent alterations (if required), bunching of cables, earthing of cable, armours etc. Painting of the apparatus case inside and outside after clearing the surface thoroughly and first coating of anti -corrosive paint and subsequent two coatings of Alluminium paint outside and Red Oxide inside and lettering. 18 mm Hylum sheet for location box shelf and 12 mm for cable termination in location box. Steel appartus case (Large) to Drg.No. CON/SK/T/8 with 4 Nos. of foundation bolts 20mm x 460mm to Drg.No. SA-112 A/M or latest. | Numbers | 32.00 | 17,067 | 5,46,144 |
| 19 | Excavation of earth pit, transportation, placing and fixing of earth electrode with construction of cement encloser to Drg.No.CON/SK/T/9 and CON/SK/T/9A and drawal of GI wire wrapped on MS strip (35 x 6 mm) from earth electrode to all signalling equipments, including fixing and soldering of lugs at both end of the wire. | Numbers | 25.00 | 1,941 | 48,525 |
| 20 | Installation, testing and commissioning of Permanent and Maintenance Free Earth pits. Installation charges : Earth pit (1 Set) It includes, Civil works related to earth pit digging, PMF earth pit installation, backfilling and chamber making. Materials for chamber including Chamber Cover | Numbers | 25.00 | 5,882 | 1,47,050 |
| 21 | Fixing of concrete cable route marker at 50 meter (approx) and at diversion pointincluding supply & transportation of cable route marker at site. Detail size & fixing ofcable route marker should be followed as per drawing no. SDO/Cable laying/020. Marker should be written as "RLY SIG" (both side).inspection by the Rep. of Sr.DSTE/Co./BSP. | Numbers | 400.00 | 408 | 1,63,200 |
| 22 | Alteration/ Modifications in the existing location boxes, fixing of equipments, cable insertion, termination, wiring, testing & commissioning, two coat painting, lettering to suit the circuits as per approved wiring diagrams. This includes filling with sand and plastering the same. | Numbers | 15.00 | 2,548 | 38,220 |
| 23 | Alteration of existing Q-series/Composite Relay Racks and cable termination racks. | Numbers | 10.00 | 19,785 | 1,97,850 |
| 24 | Wiring of Q-series/Composite Relay Racks and cable termination racks (New). | Numbers | 8.00 | 48,363 | 3,86,904 |
| 25 | Installation, wiring, testing and commissioning of Digital Input 1024, Analog Input 64 datalogger system as per RDSO specification no. IRS:S-99/2006 (ammedent - 3) or latest including networking and central monitoring along with installation of remote monitoring software and hardware. The contractor is also required to list out the no. of analog & digital inputs for wiring & operation of the datalogger by taking approval of the Rly. for those inputs. This includes training to 4 staff at site. | Numbers | 1.00 | 46,786 | 46,786 |
| 26 | Modification/Alteration of Data Logger/RTU Digital Input, validatory & yard simulation in both end station of IBS as per directive of Railway Representative . | Numbers | 4.00 | 43,453 | 1,73,812 |
| 27 | Fixing, cable drawing and termination, wiring, painting, lettering, testing and commissioning of Junction type Route indicator complete along with lamp/LED unit. 3/4 Way | Numbers | 2.00 | 3,086 | 6,172 |
| 28 | Transportation, Installation, Testing & Commissioning of fuse indication cum monitoring and automatic changeover system. | Numbers | 12.00 | 9,469 | 1,13,628 |
| 29 | Installation, Testing and Commissioning of Track Circuits (Straight portion of track circuit) as per Drg.No:SK/DRG/OL/27 and track bonding plan including drilling of 9/32" holes on rails, provision of bonding, block joints (90R/52Kg/60 Kg) with machined fish plate or Glued Joints, fixing and painting of track lead junction boxes, fixing of 25 mm nominal dia GI pipe of required length with 9/32" holes at 10 cm. apart for protection of tail cables, insulation of lead wires from rails using heat shrinkable tape, insulation of traction bonds below rails with 3mm thick heat shrinkable tapes, fixing of lead wire suitably with sleepers. Provision of tail cable termination, fixing of double track lead wires, jumper wires, terminals, track charger, adjustable/fixed resistance, choke coil, fuses, battery, track relay etc., and also lettering/numbering of track lead junction boxes, block joints and track circuits. | Numbers | 8.00 | 3,832 | 30,656 |
| 30 | Installation, Testing and Commissioning of Track Circuits (Point and crossing portion of track circuit) as per Drg.No:SK/DRG/OL/27 and track bonding plan including drilling of 9/32" holes on rails, provision of bonding, block joints (90R/52Kg/60 Kg) with machined fish plate or Glued Joints, fixing and painting of track lead junction boxes, fixing of 25 mm nominal dia GI pipe of required length with 9/32" holes at 10 cm. apart for protection of tail cables, insulation of lead wires from rails using heat shrinkable tape, insulation of traction bonds below rails with 3mm thick heat shrinkable tapes, fixing of lead wire suitably with sleepers. Provision of tail cable termination, fixing of double track lead wires, jumper wires, terminals, track charger, adjustable/fixed resistance, choke coil, fuses, battery, track relay etc., and also lettering/numbering of track lead junction boxes, block joints and track circuits. | Numbers | 8.00 | 4,209 | 33,672 |
| 31 | Installation of signal posts for Multiple Aspect Colour Light Signals complete with signal units, bases, LED unit, fixing and wiring of current transformers of LED units, ladders & other fittings, excavation of pit, casting of cement concrete foundations with necessary water outlets, erection and fixing of complete fittings of the signal/signal post with necessary earthed screen protection arrangement, including drawing of cable through signal posts, termination of cables, wiring, testing and commissioning, two coat painting and lettering, supply and fixing of speed boards if required for the following:- NOTE:- The foundation for Multiple Aspect Colour Light Signal Post drg. No. Con/SK/T/12 and and the foundation bolts shall be of sizes 24 mm x 915 mm to Drg. No. SA- 116A/M and bolts for each foundation for above shall be of size 20 mm x 305 mm to Drg. No. SA- 110A/M ( 4 nos. for each) with two nuts and two washers each per bolt. 3 ASPECT/4 ASPECT | Numbers | 6.00 | 19,551 | 1,17,306 |
| 32 | Installation of signal posts for Multiple Aspect Colour Light Signals complete (2 ASPECT) with signal units, bases, LED unit, fixing and wiring of current transformers of LED units, ladders & other fittings, excavation of pit, casting of cement concrete foundations with necessary water outlets, erection and fixing of complete fittings of the signal/signal post with necessary earthed screen protection arrangement, including drawing of cable through signal posts, termination of cables, wiring, testing and commissioning, two coat painting and lettering, supply and fixing of speed boards if required for the following:- NOTE:- The foundation for Multiple Aspect Colour Light Signal Post drg. No. Con/SK/T/12 and and the foundation bolts shall be of sizes 24 mm x 915 mm to Drg. No. SA- 116A/M and bolts for each foundation for above shall be of size 20 mm x 305 mm to Drg. No. SA- 110A/M ( 4 nos. for each) with two nuts and two washers each per bolt. | Numbers | 3.00 | 17,378 | 52,134 |
| 33 | Fixing of dependent shunt signals with enameled markers including drawing of cable through the signal post, termination of cables, wiring, fixing of calling- on/dependent shunt signal legend board, LED, two coat painting and lettering, testing and commissioning as required. | Numbers | 4.00 | 4,629 | 18,516 |
| 34 | Installation, testing and commissioning of Position Light shunt signal (Independent), posts complete with lamps/LED lamps, LED units, Bases and other fittings, excavation of pit, casting of cement concrete foundation, fixing of complete fittings of signal, LED lamps, current regulator including foundation bolts, washers, nuts, termination of cables, wiring, painting and lettering as required. NOTE:- The foundation for position light shunt signal Drg. No. Con/SK/T/13 and bolts for each foundation for above shall be of size 20 mm x 305 mm to Drg. No. SA-110A/M ( 4 nos. for each) with two nuts and two washers each per bolt. | Numbers | 4.00 | 3,856 | 15,424 |
| 35 | Fixing of calling-on signals with enameled markers including drawing of cable through the signal post, termination of cables, wiring, fixing of calling- on/dependent shunt signal legend board, LED, two coat painting and lettering, testing and commissioning as required. | Numbers | 4.00 | 4,629 | 18,516 |
| 36 | Track crossing, Road Crossing by pushing method (HDD method) at culverts/ track / pucca road crossing at a depth not less than 1 meter with reference to bottom of rail/road surface including supply of GI/HDPE pipe . HDPE pipe/DWC pipe(4 inch dia). Inspection by the Rep. of Sr.DSTE/Co./BSP. | Metre | 300.00 | 1,080 | 3,24,000 |
| 37 | Installation of retro reflective signal/shunt signal enameled number legend board . | Each | 22.00 | 77 | 1,694 |
| 38 | Installation (including over hauling) of Electric point machines on MS plate fixed on wooden/PSC sleepers complete with crank handle key Interlocking arrangement as per the drawing approved by Railways, junction boxes (as suggested by the railway) with 1 ½'' dia G.I.pipe/HDPE pipe of required length up to point machine, ground connections, including smithy works involved, insulation of MS plate on which the point machine is to be fixed from the gauge tie plate involving revetting/welding of angle, cleats, termination of cables, wiring, preliminary adjustment for operation of point by crank handle and subsequent final adjustment, painting and lettering as required, testing and commissioning of the same. | Numbers | 9.00 | 12,859 | 1,15,731 |
| 39 | Installation and wiring of Rotary key transmitters/KLCR on teak wood board enclosed inside a suitable box with front transparent check cover with locking arrangement. This includes 3/4" thick teak wood boards, transparent sheet for box, locking arrangement. 2 nos.of locks for box and 1 No. lock for front transparent sheet. | Numbers | 12.00 | 507 | 6,084 |
| 40 | Laying of Power cable in the same excavated trench to Drg.No:CON/SK/T/5.Transportation, supply of 'U' clamps and anchoring of cable at every 10 Mtrs with 'U' clamp to Drg.No:CSTE/C/Cable/81. Transportation, supply and placement of 2nd class bricks in the trench length wise between power cable & other signalling/quad cable in the same trench all along the trench (4.5 bricks approx per Mtr.) including back filling with excavated earth and ramming of trenches after cable laying. Inspection by the Rep. of Sr.DSTE/Co./BSP. | Kilometre | 6.00 | 25,526 | 1,53,156 |
| 41 | Installation, cable termination, testing and commissioning of 10/20/50 Pair CT Boxes. | Numbers | 6.00 | 786 | 4,716 |
| 42 | Supply, Installation Testing and Commissioning of All-In-One PC with latest configuration. It should be as per Technical specification on Annexure "I". Make: HP, Dell or Lenovo. Remarks: Before supply of the material, consent from Rep. of Sr.DSTE/Co./BSP is to be obtained. Inspection by Rep. of Sr.DSTE/Co./BSP. | Set | 2.00 | 56,299 | 1,12,598 |
| 43 | Installation and wiring of protocol converter to suit with the dataloggers of the station . | Numbers | 2.00 | 3,208 | 6,416 |
| 44 | Transportation, Installation, Testing & Commissioning of Earth Leakage Detector. | Numbers | 1.00 | 32,894 | 32,894 |
| 45 | Installation, Testing and Commissioning of (Fire Alarm System) as per requirement at site. The work will execute as per instruction of Rep. of Sr.DSTE/Co./BSP. | Numbers | 1.00 | 14,750 | 14,750 |
| 46 | Wiring of door detection Proximity switch to the tag block of dataloggers/RTU (This includes provision of casing and capping and other wiring accessories, excluding 16/0.2 wire which will be supplied by Railways). This includes incorporation of this contact in datalogger simulation & datalogger report. | Station | 2.00 | 1,242 | 2,484 |
| 47 | Installation, Testing of door contacts and validation and proximity switch data through Dataloggers/RTU. This includes incorporation of this contact in datalogger simulation & datalogger report. | Station | 2.00 | 1,242 | 2,484 |
| 48 | Development of door 'close and open' software logics module & its implementation. | Station | 1.00 | 1,242 | 1,242 |
| 49 | Transportation, Wiring and Installation of magneto telephone at L.C.Gate/pump houseor the places as advised by the site incharge. This includes supply and fixing of Telephone rack of approved design by the contractor. | Numbers | 15.00 | 990 | 14,850 |
| 50 | Installation and Fixing of "E" type lock along with Welding Work . | Numbers | 12.00 | 704 | 8,448 |
| 51 | The excavation of pit, casting of concrete foundation including surrounding earthwork along the foundation, erection, installation and wiring of steel appartus case, fixing of terninals, fuse blocks, signal transformer, current transformer, filament switching unit, track battery chargers, adjustable/fixed resistances, choke coils, Fuses, Relays, E type locks , termination of cables, cable insertion, wiring to draw 110V AC therefore in the new apparatus case as required, testing, commissioning including subsequent alterations (if required), bunching of cables, earthing of cable, armours etc. Painting of the apparatus case inside and outside after clearing the surface thoroughly and first coating of anti -corrosive paint and subsequent two coatings of Alluminium paint outside and Red Oxide inside and lettering. 18 mm Hylum sheet for location box shelf and 12 mm for cable termination in location box. Steel appartus case (half) with 4 Nos. of SS foundation bolts 20mm x 460mm to Drg.No. SA-112 A/M or latest. | Numbers | 2.00 | 8,534 | 17,068 |
| 52 | Shifting of existing location boxes to facilitate earthwork of Engg./Con. This includes filling with sand and plastering inside location boxes. | Numbers | 7.00 | 3,580 | 25,060 |
| 53 | Supply and Installation of Surge Protection Device for Track Circuits as per Annexure "II" item no. 1. The supplied SPDs shall have certification (CERTIFICATE ATTACHED) of IEC Standard-- National/International Labs like CE/KEMA/EAC/UL/NABL or any other accredited test lab. Insp.by Rep. of Sr.DSTE/Co./BSP. | Numbers | 14.00 | 3,514.53 | 49,203.42 |
| 54 | Supply and Installation of Surge Protection Device for Track Circuits as per Annexure "II" item no.2. The supplied SPDs shall have certification (CERTIFICATE ATTACHED) of IEC Standard-- National/International Labs like CE/KEMA/EAC/UL/NABL or any other accredited test lab. Insp. by Rep. of Sr.DSTE/Co./BSP. | Numbers | 14.00 | 3,514.53 | 49,203.42 |
| 55 | Supply and installation of 'AXLE COUNTER section ' Board on steel rectangular board of size 600mmX1000mm, 3mmthick legend on coloured retroreflective tape engineering grade( yellow background, lettering AXLE COUNTER section in black)as per GR and rectangular board fitted on rail post through 2 nos. of suitable clamps. Inspection by Rep. of Sr.DSTE/Co./BSP. | Numbers | 4.00 | 8,796 | 35,184 |
| 56 | Horizontal direction drilling (HDD)/Trenchless digging/machine drilling without damage to surface road track for laying/insertion of HDPE/GI/DWC pipe. The bore shall be done of min. diameter of 120 mm & at a depth of a minimum 1400 mm from the ground level. The ground level shall be considered ignoring the bank height of the bank of the road. Note:-DWC/HDPE/GI Pipe supply is not covered under this item. Contractor shall provide all material required for the work and adequate nos, of labours for propper laying of cables into the bore. Cable shall be laid catiously so that it should not get damaged due to rough handling & pressure on cable. Payment of boring shall be made only after two nos. of DWC/HDPE (40 mm dia.)/GI pipe is laid in the bore. | Metre | 300.00 | 376.68 | 1,13,004 |
| 57 | Supply, Installation, Testing & Commissioning of Earthing arrangement for EI system as per the latest RDSO drawing Circulated vide letter no. RDSO-SIG0SPD(PROJ)/1/2020 date08.01.2025 STS/E/TAN/3006 ver 3.0for earthing & Bonding scheme. Here1 job unit stands for location. Inspection by the RDSO. | Numbers | 3.00 | 5,01,800 | 15,05,400 |
| 58 | Earthing of EI eqipment, relay rack and power equipment etc to be done along with the supply of all requisite materials, earthing shall be in the form of Ring Earth conforming to RDSO spec RDSO/SPN/197/2008 (with a minimum 6 maintenance free earth electrodes) using copper rings with earth resistance less than 1 ohm. The earthing shall be maintenance free. The ring earth shall be connected to copper flat of size 25x3 mm in the relay room and IPS room. The copper flat fixed on the wall to the entire breadth of Relay room and IPS room as an earth bus bar and all earth connections shall be taken from it. A, B ,C & D class protection shall be provided for all EI equipment. Inspection by the RDSO. | Job | 1.00 | 1,45,808 | 1,45,808 |
| 59 | Supply, Installation and commissioning of Surge & Lightning protection arrangement in the cable huts for all the equipments including all the circuits derived from MUX at the stations and Ring Earth (Six Earth pits). Each earth shall be as per RDSO Specification No.RDSO/SPN/197/2008. Inspection by the RDSO. | Station | 1.00 | 49,643 | 49,643 |
| 60 | Dismantling of the following:- Steel apparatus case with fittings. | Numbers | 22.00 | 232 | 5,104 |
| 61 | Dismantling of the following:- Relay racks with all fittings, battery racks complete, Equipment rack complete, SM's slide. | Numbers | 5.00 | 360 | 1,800 |
| 62 | Dismantling of the following:- Battery charger, Battery set etc.TLBI, DLBI and other Misc. equipments. | Numbers | 10.00 | 229 | 2,290 |
| 63 | Dismantling of the following:- Electric Point Machine | Numbers | 3.00 | 603 | 1,809 |
| 64 | Dismantling of the following:- Signal posts/BSLB/SLB/Stop Board. | Numbers | 1.00 | 232 | 232 |
| 65 | Dismantling of the following:- Operating cum indication Panel. | Station | 1.00 | 2,415 | 2,415 |
| 66 | Collecting, Stacking with deployment of Man power, Hydra etc for Loading/ Unloading and Transportation of Materials (Fresh/Released/Unused) from (i) work site to GSD/Raipur, (ii) work site to the stotre of the consignee, (iii) any store depot to any other store depot over Indian railways as decided by Railway Administation by suitable Trucks and stacking properly. | MT-Km | 3800.00 | 38 | 1,44,400 |
| 67 | Provision of simulation arrangement(Track and Point simulation board as well as signal lamp simulation board) and its complete wirinig; arrangement of free home, advance starters, IBS etc as may be required with block working with required temporary relay wiring for controlling the train movement in NI - period with the provision of temporary miniature operation cum indication panel board; deputation of fitter round the clock in NI - period for assisting simulation testing for all the routes as per approved RCC by the Railway officials ; mobilization of additional man power for attending to the Pre - NI block and commissioning of the station within prescribed time limit of NI - period as decided by Railway officials; deputation of staff (one fitter & one helper) at the station for attending to the packing and reallignment of point and crossing etc, in connection with P. Way block for a period of 30 days beyond the commissioning date. (a) Station upto 6 lines | Numbers | 2.00 | 3,72,446.5 | 7,44,893 |
| 68 | Supply of Unskilled labour for immediate restoration of normal traffic by jointing Signalling/Telecom/Power cables of damaged during excavation of earth work of engineering department or for shifting, stacking of stores materials. Unskilled staff will remain available in working hours. | Man- Days | 50.00 | 266 | 13,300 |
| 69 | Physical tracing and opening/locating of existing working cables by precession digging for diversion of cables in connection with cable clearance for engineering earth work without interfering the circuits as per the advice of Rep. of Sr.DSTE/Co./BSP. | Metre | 150.00 | 241 | 36,150 |
| 70 | Deployment of Prokline/ Hydra operation at site for exposing the burried cables or relocation the Location Box/ Signal Post with foundation as per the advice of Rep. of Sr.DSTE/Co./BSP. | Hour | 70.00 | 603 | 42,210 |
| 71 | Arrangement for commissioning of station for the work of Non-Interlocking period at site such as provision of 2 Tent, 4 Table Chair (08 No. in each Tent) in general, Drinking water & other amenity, cap, Umbrella Torch for 30 staff, Hand Glovesfor 06 to 08 staff and arrangement of one vehicle at each work for the work of NI period for required commissioning of station for the work of Non- Interlockingperiod at site. Lighting arrangements in Tents, in the Yard over point zone for proper working in the evening and night as required. If necessary, DG has to be arranged by the contractor on his own cost including Diesel, lubricant oil etc. Necessary arrangements should be done as advices by the Railway site Engineer. | Day | 6.00 | 35,400 | 2,12,400 |
| Schedule total | ₹1,16,47,984.6 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
15-AllAnnexures.pdf
ATTACHMENT
Annexure-A-MSDAC.pdf
ATTACHMENT
FRPPointJBDrawing.pdf
ATTACHMENT
TypicalforSteelAppratusCaseLarge.pdf Typical for Steel Apparatus Case
ATTACHMENT
IRSEMBasedDrawings.pdf
ATTACHMENT
Annexure-VIB-TurnoverData.pdf
ATTACHMENT
Annexure-VandVA.pdf
ATTACHMENT
Annexure For Retired Railway
ATTACHMENT
CLFproposedMini16.05.26.pdf
ATTACHMENT
KGSLONGHAULLOOPLINE_1.pdf
ATTACHMENT
SOR.pdf
ATTACHMENT
Annexure-J-RetiredRailwayEngineerFormat.pdf
ATTACHMENT
TypicalforSteelAppratusCaseLarge.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].