CWE/AF AMB/AMB-14/2023-24 SPECIAL REPAIR TO WATER DISTRIBUTION MAINS AT CERTAIN LOCATIONS AT AFS AMBALA UNDER GE (AF) AMBALA

Amount

Taking down chowkhats or frames not exceeding 1.5 sqm each with shutters (without taking off shutters from the frame) and removing from site, complete all as specified & directed.

Taking down chowkhats or frames exceeding 1.5 sqm but not exceeding 4 sqm each with shutters (without taking off shutters from the frame) and removing from site, complete all as specified & directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as per specification & drawing shown on page No. 176 of SSR Part-II, 2020 (Section - 8, Joinery)

S&F factory made, solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with mild steel square tube, complete all as per specification & drawing shown on page No. 180 of SSR Part-II, 2020 (Section - 8, Joinery)

S&F butt hinges, size 100mm long, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified & directed.

S&F 150mm long, aluminium, anodized, barrel tower bolt of extruded section complete all as specified & directed

S&F anodised aluminum handle, cast type ,150mm long complete all as specified & directed.

S&F factory made Box type steel window, double shutter, glazed and wire gauzed with side hung shutters including box type hinges, steel handles fabricated type for each leaf duly welded, mild steel barrel tower bolts 150mm size (02 Nos for each leaf) duly welded, complete with glazing bars dovetailed or welded including MS fillets and MS grill of 8mm square bar complete all as specified & directed. Notes: - (i) Windows shall be fabricated as per drawing No. TD-219 Sh 1/3 to 3/3 and these drgs may be referred from GE office or from the office of CWE (AF) Ambala. (ii) Glazing & Wire cloth shall be measured and paid separately . (iii) Painting to window shall be measured and paid separately however one shop coat primer included in quoted rates. (iv) Double shutter meant for providing glazed shutter as well as wire gauged shutter on outside & inside of the frame respectively. Both the shutters shall be measured as one unit. (v)Steel window shall comply with IS 1038-1983 &. Rolled steel sections for fabrication shall conform to IS 7452-1990

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or stainless steel wire staple etc. complete all as specified & directed.

M&L preparation of new steel and iron based surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over & including one coat of red oxide primer complete all as specified & directed.

S&F sheet glass 3mm thick, ordinary quality, glazing with oil putty in squares not exceeding 0.5 sqm in each pane fixed with oil putty or wooden beads including glazing pins/ spring clips wherever necessary etc. complete all as specified & directed.

S&F 3.0 mm thick figured glass, pin head type, glazing with oil putty in squares not exceeding 0.50 sqm in each pane fixed with oil putty or wooden beads including glazing pins/ spring clips wherever necessary etc. complete all as specified & directed

M&L in repair cast iron nahani trap 100mm dia outlet with grating including jointing to waste pipe fixed in cement concrete type B-1(1:2:4) complete all as specified & directed.

S&F in repair 15 mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified & directed.

S&F in repair bib tap 15 mm bore, chromium plated, long body, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & directed.

S&F in repair brass chromium plated tubular towel rail 20mm dia , 60cm long, superior quality , between flanges fixed to wall with brass CP screws complete all as specified & directed.

S&F in replacement PVC low level flushing cistern, white, valveless syphonic action type 10 litre capacity with inlet, ball valve, float and handle including PVC flush pipe 32 mm dia with bend and a pair of mild steel angle iron brackets of suitable size including making necessary connections to water supply pipe line and WC, complete all as specified & directed.

S&F in replacement vitreous china wash hand basin, oval type, white, size 550mm x 400mm including 32mm bore PVC waste pipe of suitable length, CP waste fitting & one pair of mild steel angle iron brackets of suitable size fixed as in counter slab complete all as specified & directed.

S&F in repairs soap dish, brass, chromium plated, size 160mm x 160mm x 90 mm fixed with and including plugs with brass CP screws complete all as specified & directed.

S&F in repair vitreous water closet china squatting pan, Orissa pattern, 580mm x 440mm, white, with and including PVC ‘P’ or ‘S’ trap front or back inlet with integral foot rests excluding flushing cistern and flush pipe including providing lime concrete bedding and making good to floor etc. complete all as specified & directed.

S&F in repair 15mm bore fancy type stop valve/angle valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes complete all as specified & directed.

S&F PVC connection 450mm long with 2 nos PTMT check nuts, suitable for 15mm bore complete all as specified & directed

Dismantling old unserviceable PVC water tank of capacity exceeding 250 ltrs but not exceeding 500 ltrs cpacity including S&F rotational moulded polyethylene(PVC) water storage tank, HDPE, triple layered , cylinderical type fixed and hoisted in position on roof, at any height, of capacity 500 litre and making connections with 20 mm GI pipe inlets & outlets complete including locking arrangements and 20 mm bore ball brass valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gram) complete all as specified & directed.

S&F in repair 20mm bore stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes complete all as specified & directed.

Dismantling of brick tiles or terracing tiles, single layers on roof and rubbish off the premises including stacking of servicable brick tiles(if any) complete all as specified & directed.

Demolition of mud phuska on roofs, any thickness including mud plastering & leeping (whether full thickness removed or only a part thereof) and rubbish off the premises to a distance not exceeding 500 mtr complete all as specified & directed.

M&L plain cement concrete(PCC) 1:2:4 type B-1 using 20mm graded mechanically crushed stone aggregates as in padding on roof slab to maintain the required slope / to make good the depressions and finished the surfaces even and fair complete all as specified & directed.

M&L plain cement concrete(PCC) 1:2:4 type B-0 using 12.5mm graded mechanically crushed stone aggregates as roof kerb(gola) complete all as specified & directed.

M&L water proofing treatment to roof slab complete all as specified here-in-below & as directed by Engineer-in-charge:- (i) Levelling of surface to give proper slope will be done as per site requirements with Bituminous Mortar & Cold Emulsion cum waterproofing Liquid of water based bituminous emulsion. (ii) Creating SSD condition on surface with water. Prime the surface with acrylic modified bitumen with potable water in the ratio of 1:1 and apply @400gm per Sqm (As per Surface Conditions). (iii) Apply first coat of acrylic modified bitumen having elongation 200% conforming to ASTM-C-412 & having crack bridging of 8mm confirming to ASTM-C-836 with tensile strength after 7 days 0.50mm conforming to ASTM-C-412 with no diluation of water on primed surface while the surface is still tacky with consumption of 700gm per Sqm. (iv) Laying Geotex of 45 GSM/ Fibre mesh simultaneously and paste it properly with overlap of 50mm. Allow the first coat to dry for 10 hrs to 12 hrs. (v) Apply second coat on cured first coat with consumption @ 700gm per Sqm in opposite direction of first coat by Brush or Roller. Allow it to dry for 10-12 hrs. (vi) Apply third coat with consumption @ 700gm per Sqm. Ensure final curing time of 36 hrs before allowing/ carrying out any further work.

Item No. 30 continued...../- (vii) Conduct ponding test for minimum 7 day after applying two coats of single component , UV Resistant Elastomeric Exterior Acrylic Weather resistant water proof coating having elongation of 300% after curing of 14 days confirming to ASTM D- 6083--for UV Protection of Bituminous Elastomeric Acrylic Emulsified Liquid Membrane to give long life and prevent its deterioration from sunlight. Notes:- (i) The water proofing treatment shall be got carried out by the manufacturer or their authorised applicators only duly approved by GE in writing. (ii) For guarantee & security deposit refer Particular specifications.

Dismantling of 100mm or 75mm internal dia cast iron pipe or reinforced concrete drain pipes, jointed in cement mortar and taking out from fixed on wall complete all as specified & directed.

S&F PVC Soil Waste & Rainwater(SWR) pipe 110mm bore single socketed in any length with rubber ring joints, fixed to wall complete all as specified & directed.

S&F PVC (SWR) bends any radius, for 110mm bore of pipe complete all as specified & directed.

Taking up or down steel water tubing and connections for refixing or removal from site,15 mm bore pipe complete all as specified & directed.

Taking up or down steel water tubing and connections for refixing or removal from site, 20 mm bore pipe complete all as specified & directed. Note for BOQ item 34 & 35: Cutting chasing wherever required at any location is deemed to be included in quoted rates.

S&F galvanised mild steel water tubes 15 mm bore, medium grade, with all fittings, fixed to wall and ceiling or laid in floor including cutting chasing for concealed wherever required & making good complete all as specified & directed.

S&F galvanised mild steel water tubes 20 mm bore, medium grade, with all fittings, fixed to wall and ceiling or laid in floor including cutting chasing for concealed wherever required & making good complete all as specified & directed.

Fixing only galvanised mild steel water tubes 15 mm bore with all fittings, fixed to wall and ceiling or laid in floor including cutting chasing for concealed wherever required & making good complete all as specified & directed.

Fixing only galvanised mild steel water tubes 20 mm bore with all fittings, fixed to wall and ceiling or laid in floor including cutting chasing for concealed wherever required & making good complete all as specified & directed. Note for BOQ item No. 38 & 39: The old serviceable tubing obtained from BOQ item No. 34 & 35 shall be used after proper cleaning.

M&L 75mm thick PCC 1:3:6, type C-2, using 40mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10mm wide, 30mm deep joints at the rate of 3.00 mtr centre to centre and at every turning & filling the joints with bitumen & sand mixture complete all as specified & directed. Notes :- (i) The unit rate quoted shall be deemed to include for providing the concrete in alternate bays not exceeding 3 Mtrs length. (ii) 30 mm deep joints between the bays shall be provided which shall be filled with mastic filling with hot bitumen 85/25 grade and 1:2 mix volume.

M&L 100mm thick plain cement concrete(PCC) 1:3:6 type C-2 using 40mm graded mechanically crushed stone aggregates as in hardstanding / path, surface finished even & fair complete all as specified & directed.

M&L chequered cement concrete tiles 20cm x 20cm, 25mm thick with grey cement and pigment , set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over & including 15mm thick screed bed or bedding layers in cement mortar 1:4 complete all as specified & directed.

M&L 60 mm thick, M-35 grade of concrete, machine pressed precast concrete interlocking paver block, any shape, design & size conforming to IS 15658-2006, with grey cement and pigment finished with coloured rubber finish on top over & including a layer of fine sand cushioning 25mm consolidated thickness complete all as specified & directed.

Demolition of Plain cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) including removal of debris to a distance not exceeding 500 mtr complete all as specified & directed

M&L cutting/chipping the spalling concrete surfaces of chajjas/roof protection etc. and trimming & cleaning the surface to recieve gunting and providing pressure gunnting average 20mm thick in PCC 1:2:4 type B-0 and finishing the concrete surface with 5mm thick plastering in cement mortar 1:4 even & smooth without using extra cement including welding the reinforcement to existing reinforcement complete all as specified & dirceted Note: (i) Reinforcement shall be measured seperately. (ii) Necessary formwork required for the work shall deemed to be included in quoted rates. (iii) Necessary scaffolding as required at site shall be provided by contrator without any extra cost and shall remove the same on completion of the work.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises to a distance not exceeding 500 mtr etc. complete all as specified & directed.

M&L coloured, non- skid joint free, edge cut, ceramic tiles, 1st quality, 7mm to 8mm thick, square/rectangular, area of each tile exceeding 0.11Sqm but not exceeding 0.18 Sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over & including 15mm thick screed bed or bedding layers in cement mortar 1:4 complete all as specified & directed.

M&L glazed ceramic designer coloured tiles of size 300mm x 450mm, 7mm to 8mm thick as in vertical surface (skirting/dado etc.) set and jointed in neat cement slurry & pointed in white or coloured cement to match the surface over & including 10mm thick rendering/backing coat in cement mortar 1:4 complete all as specified & directed.

M&L 25 mm thick plain cement concrete(PCC) 1:2:4 type B-1 using 20mm graded mechanically crushed stone aggregates as in floor, finishing the surface even & fair complete all as specified & directed.

M&L mild steel TMT bars 10mm dia and over, Fe500/Fe500D grade confirming to IS-1786, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed.

Taking down cement or cement lime plaster on brick or stone walls, soffits of slab/shajja/sunshade etc. including racking out joints, hacking for key, scrubbing down with water including removal of debries to distance not exceeding 500 mtr complete all as specified & directed.

M&L rendering 15 mm thick in cement mortar 1:6 on fair faces brick or concrete surfaces as in wall, finished even and smooth without using extra cement complete all as specified & directed.

M&L rendering 5 mm thick in cement mortar 1:3 on the soffit of slab/chajjas/ sunshade etc finished even and smooth without using extra cement complete all as specified & directed.

M&L rendering 15 mm thick in cement mortar 1:4 on other than fair faces brick surfaces as in wall, finished even and smooth without using extra cement complete all as specified & directed.

M&L rough cast plaster including 15 mm thick rendering in cement mortar 1:3 on brick work or concrete surface all as specified in SSR Part -1 clause 14.22 complete all as specified & directed. Note : Rough cast plaster finish shall be as follow :- After applying the under coat in cement mortar 1:3 and while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel aggreagte (Which is generally of size between 6mm to 12mm depanding on the texture required mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even. The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure the larger aggregate are throughly covered.

Demolition of brick work or stone/boulder masonary built in cement mortar including all quoins, pillars etc but excluding ashlar facings, dressed stone work and precast articles complete all as specified & directed.

M&L Brick work with sub class B, burnt clay bricks of old size, designation 75, straight or curved on plan exceeding 6 mtr mean radius, built in cement mortar 1:6 complete all as specified & directed.

M&L plain cement concrete(PCC) 1:2:4 type B-2 using 40mm graded mechanically crushed stone aggregate as in foundation, filling and mass concrete complete all as specified & directed.

M&L preperation of newly plastered surface of wall and applying three coats of white wash complete all as specified & directed.

Complete removal of existing treatment from old decorated plastered surfaces of ceiling/soffits and applying two coat of white wash complete all as specified & directed.

M&L preparation of newly plastered surfaces of wall and applying two coat of cement base paint of approved shade/tint over & including one coat of alkali resistant primer complete all as specified & directed.

Complete removal of existing treatment from old decorated plastered surfaces of wall and applying applying two coat of cement base paint of approved shade/tint over & including one coat of alkali resistant primer complete all as specified & directed.

M&L preparation of newly plastered surfaces of wall and applying two coat of exterior acrylic emulsion paint in camoflaging pattern of approved shade/tint over & including one coat of alkali resistant primer complete all as specified & directed.

Demolition of stone slabs and tiles of any description or thickness as in floors, aprons etc, laid, bedded & pointed in any mortar and rubbish off the premises to a distance not exceeding 500 mtr complete all as specified & directed.

M&L machine cut Kota stone slab 18mm to 20mm thick as in flooring, laid over & including 15 mm thick screed bed in cement mortar 1:6, and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified & directed.

S&F self-coiling (push pull or manual type) steel rolling shutters 1.25mm thick lath conforming to IS 6248-1979, with & including ball bearing & MS 04 levers saftey lever lock as specified in SSR Part - I including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position complete all as specified & directed. Note: Quoted rates are deemed to be included for requisite Nos. of ball bearing & saftey lever lock in one rolling shutter as specified.

M&L preparation of old or previously treated steel and iron based surface of any description over 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified & directed.

S&F mild steel plain black sheet 1.00mm thick as in hearths; covering to door shutters; covering to door chowkats (frames); chullah hoods; water tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified & directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified & directed.

M&L dewatering of existing water from under ground sump with help of pump or any by other means as directed by Engineer-in-charge and making suface dry complete all as specified & directed. Note: The volume of existing water in UG sump shall only be measured & paid.

M&L water proofing treatment to floor & wall of under ground Sump as described below complete all as specified & directed:- (i) Cleaning & preparation of old RCC / PCC / Brick surface of Sump, above or below ground level, removing grass/algae/fungus/loose concrete & plaster and making surface clean, dry & dust free. (ii) Repairing & strengthening, cutting of joints in 'U' & 'V' shape, applying SBR latex based onding agents, filling joint with high strength fiber reinforcement, M-50 grade ready to use mortar. (iii) Applying foure coat water proofing treatment, 1st coat of SBR latex, 2nd coat of component elastomeric flexible water tight, crack bridging water proofing coat, 3rd coat with same sandwich layer of 45 gsm glass fiber mesh and 4th coat of same. Notes: (i) The water proofing treatment shall be got carried out by the manufacturer or their authorised applicators duly approved by GE in writing. (ii) For guarantee & security deposit refer Particular specifications.

Excavation in trenches, not exceeding 1.5mtr wide and not exceeding 1.5mtr in depth; for foundation, laying/taking out pipes/cables etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10sqm on plan & not exceeding 1.5mtr in depth and getting out, in soft/loose soil complete all as specified & directed. Note: Wherever the work executed for pipe lines, the bottom surface shall formed to required level & slope without any extra cost to department.

Removal of excavated soil to a distance exceeding 250 mtr but not exceeding 500 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified & directed.

M&L plain cement concrete(PCC) 1:3:6 type C-2 using 40mm graded mechanically crushed stone aggregate as in foundation, filling and mass concrete complete all as specified & directed. Note: Necessary formwork wherever required at site deemed to be included in quoted rates.

M&L plain cement concrete(PCC) 1:2:4, type B-1 (using 20mm graded mechanically crushed stone aggregate) in surface channels & drains including necessary formwork complete all as specified & directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc. complete all as specified & directed.

Add or deduct in quoted rates of item 76 here-in-above for each 25 mm girth or part thereof over or under 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc. complete all as specified & directed.

M&L Brick work with sub class B, burnt clay bricks of old size, designation 75, straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified & directed.

M&L plain cement concrete(PCC) 1:2:4, type B-0, using 12.5 mm graded mechanically crushed stone aggregates as in lintels upto 1.5mtr clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork to complete all as specified & directed.

M&L flush pointing to brick wall in cement mortar 1:3 including racking out joints complete all as specified & directed

Returning, filling in including spreading leveling watering and well ramming in layers not exceeding 25 cm thick each in soft/loose soil complete all as specified & directed.

Removal of excavated soil to a distance not exceeding 50 mtr & depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified & directed.

Supply, laying, testing & commissioning centrifugally cast (spun) ductile iron pipes of 100 mm dia laid as in trenches, spigot & socket end, class 'K-7' conforming to IS:8329/2000 amended upto date, inlcuding push on tyton joint / rubber gasket jointing with inside cement mortar lining with portland slag cement as per IS 455 :1989 and external metallic zinc coating as per IS:8329 with finishing layer of bitumen coating, duly ISI marked in any length complete all as specified & directed.

Supply, fixing, testing & commissioning of Double flanged non-rising stem type cast iron sluice valve suitable for 100 mm dia/bore pipe with hand wheel and suitable for pressure rating of PN 1.6 duly drilled holes for fixing of nuts and bolts, stem made of high tensile brass ISI marked and conforming to IS 14846 - 2000 including rubber gasket, nuts, bolts and washers complete all as specified & directed.

Supply & jointing heavy duty (K-12) DI Bends upto 100mm bore (any type, radius and angle ), Tapers any type, (straight, bend, increasing, decreasing or double socket etc), Tee pieces single branch, Y junction, Double branch, Cross (all sockets or socket and spigot or all flanged or one end flanged and other ends spigot /socketed), Collars, Caps and Plugs, MJ collar coupling etc., conforming to IS 9523 - 2000 inlcuding it's push on tyton joint / rubber gasket jointing complete all as specified & directed.

M&L boring of holes under road, pavement, taxi track, hardstanding for passing/crossing pipes/cables upto size 150mm dia/bore at suitable depth (not below than 600mm) by trenchless technology using ultra sounding technique and using necessary machinery / equipments complete without damaging the surface and removing excavated soil /material to a distance not exceeding 50mtr complete all as specified & directed.

Excavation in post holes each not exceeding 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50mtr and making good surface complete all as specified & directed

S&F mild steel work such as angle iron in posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc., flat iron fillets (for securing wire mesh etc) including necessary welding where required as per site requirement and other similar works complete, conforming to Gde E-165 (Fe-290) including dismantling of old MS works complete all as specified & directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft and loose type of soil, complete all as specified & directed.

M&L plain cement concrete(PCC) 1:4:8 type D-2 using 40mm graded mechanically crushed stone aggregate as in foundation, filling and mass concrete complete all as specified & directed.

M&L Damp proof course 40mm thick in cement concrete 1:2:4 type B-0 (using 12.5mm graded mechanically crushed stone aggregate) mixed with water proofing compound to horizontal or vertical surface including necessary formwork complete all as specified & directed. Note: Supply & mixing of Water Proofing Compound(WPC) as per manufacturer's instructions included in quoted rates and nothing extra shall be paid for WPC.

M&L applying evenly a coat of blown type bitumen @ 1.50 kg per sqm and blinding with clean dry sand @ 0.05 cum per sqm complete all as specified & directed.

M&L polythene film, 50 micron thick laid over & including one coat of bitumen primer @ 0.30 to 0.50 Kg per sqm complete all as specified & directed.

M&L brick work with flyash burnt bricks (IS-13757), old size, Designation 75, straight or curved on plan exceeding 6mtr mean radius, built in cement mortar 1:4 complete all as specified & directed.

S&F mild steel screw bolts (machine made) with hexagonal head at one end and screwed the other end or screwed both ends, each screwed end to be fitted with one washers and with one hexagonal nut of exceeding 5cm but not exceeding 10cm length with dia of neck 11mm to 15mm including dismantling of old MS nut, blot, washer etc. complete all as specified & directed.

S&F galvanized iron chain link fencing 4mm dia, made of mild steel GI mesh 50mm x 50mm weight not less than 4Kg per Sqm, binding the same with binding wires including all necessary drilling , bolting or riveting etc including dismantling of old chain link fencing complete all as specified & directed. Notes: (i) Line wire 10mm dia, MS flat iron & Nut/bolts shall be measured & paid seperately. (ii) A BOO of officers shall be ordered by GE to as certiain the unit weight of chain link fencing and shall be measured accordingly.

S&F mild steel round bars as in tie bars of 10 mm dia, fixed to fencing posts including cut to length, bent to shape, welding of bar at spots as directed and other similar works, conforming to Fe 290 (Gde -E-165) including dismantling of old MS bar complete all as specified & directed. Note: Cost of cutting to length, bent to shape rquired & binding with MS wire is included in above

S&F Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. including dismantling of old barbed wires complete all as specified & directed.

M&L preparation of old plastered surfaces of wall and applying two coat of exterior acrylic emulsion paint in camoflaging pattern of approved shade/tint complete all as specified & directed.

M&L preperation of newly plastered surface of ceiling / soffits and applying three coats of white wash complete all as specified & directed.

For Credit Schedule refer tender documents. The amount of credit schedule shall be deducted in total quoted amount of BOQ to arrive contract sum.

ANIL CONSTRUCTION CO.

KULWANT SINGH