Loading…
Loading…
Tender Value
₹10.7 L
EMD Value
₹10,800
Closing Date
25 Feb 2026, 6:00 pmClosed
Similar tender results from the same govt authority in the past 3 years.
Chief Officer, Veraval-Patan Joint Nagarpalika, Veraval
Installation of High Mast Tower at various Gardens of Veraval-Patan city.
277938
Muni./Streetlight/2774
Open
Electrical - Lighting and luminaries
Gir Somnath
3 documents required · 3 mandatory
₹900
Veraval Patan Joint Municipality Veraval
₹10,800
18 Feb 2026
18 Feb 2026
18 Feb 2026
25 Feb 2026
18 Feb 2026
Description Qty Unit Rate L.Cess Amount
Supplying, erecting, testing, commissioning
approved make M.S. Polygonal High Mast
Pole having following general Specification.
(a) Polygonal Section fabricated from M.S.
Plate confirms BSEN 10025 & Hot deep
galvanized minimum 65/86 micron (as per IS
2629 /1985) Lantern carriage with ring and
rubber lines for erection of luminaries of
(b) Maximum telescopic section not more
(c) Double drum gear pipe motorized winch
with 6mm dia S.S. Rod (For 16 mtr and
(d) Approved make L.E.D. aviation light =
No. Lightening arrestor = 1 No. with
necessary wiring of 2.5 sq.mm 5 core ISI
copper cable Unarmoured.
(e) Bottom most section suitable for
mounting reversible motor and switchgears
having door not more than 1400mm x
300mm with waterproof gasket & hinges &
locking arrangement.
(f) Pole structure comprises suitable size of
reversible motor, cable and necessary
switchgears with control panel.
(g) bottom section shall have suitable size of
thickness supports ribs foundation bolts nuts
(h) Item not comprises the cost of lanterns.
(i) Necessary Cement Concrete foundation
as per IS including testing & commissioning
of the entire structure for following size of
High Mast poles
[1] High Mast 12 Mtr. TOP A/F 105 mm,
BOTTOM A/F 360mm, No. of Sec. No. -
Bottom Thickness - 3 mm, Size of Base Plate -
Dia 520 mm x 20 mm thick, Foundation Bolt
Size M24 x 850 mm, Qty - 6 Nos., Suitable 3 No 140214.00 141616.14
for mounting Fitting of Light - 6 Nos.(6-8-1)
Supplying and erecting LED street light /
Flood light fittings with High power White
LEDs wattage of 3 Watt and above
assembled on single MCPCB, efficiency more
than 130 lm/w and corrosion free High
pressure die cast aluminum housing with
smooth finish powder coated and heat sink
extruded aluminium with diffuser and
Polycarbonate optics/ lenses, with
toughened glass with company mark/name
engraved or embossed 160 to 270 V,Power
Factor more than 0.95, THD < 10 %, CCT
3000 K to 5700K,Uniformity ratio >0.45,
2 Luminaire efficacy> 100 lumens/watt . LED
driver efficiency > 85 %.( fittings required
LM-79 & LM-80 certificates)(NOTE: Below
description have shown ranges of Wattage
capacity of LED fittings.The Engineer
incharge may select any wattage capacity
between the ranges shown.)
(B) Flood Light (IP-65), Surge protection -
4KV integral and ,Light must have 440VAC
line supply with over-voltage protection. (2-
(iv) above 90 to 120 watts Cat-lll 18 No 7,195.00 7266.95
Providing and erecting XLPE(IS:7098)(I)-88
ISI armoured cable multistrand / Solid
Copper conductor for 1.1 KV. to be laid on
wall with necessary clamps or in existing
trench / pipe at road crossing or floor of
following size of cables. (4-4-4)
Providing & laying approved make Double
walled corrugated pipes (DWC) of
polyethylene(conforming to IS 14930 II )with
necessary connecting accessories of same
material at required depth in existing trench
for laying of cable. below ground / road
surface for enclosing cable (4-5-8)
(C))90 mm outer dia 1000 Mtr 95.00 95.95
Making trench in Hard Murrum / Tar Road of
suitable width of 90 cm or required depth
for laying any size of cable or locating the
fault all over the run and back filling the
same and making the surface as normal
ground. (4-5-2)
(B) If additional machinery like hammer
driller or JCB use [Add]
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
RAW_HTML
DTP_01.pdf
Schedule B_01.pdf
Download all tender documents and submit your bid