COMPREHENSIVE AND WELCOME MAINT IN OTM/ MD ACCN IN POCKET 3 AND 4 IN AGE B/R-I UNDER GE ROORKEE

M&L for cement concrete (type B2 1:2:4, 40 mm graded aggregate) as in foundations, filling and mass concrete including Demolition of cement concrete in ground floor & paving, n. exc 15 cm thick (below or above GL), unreinforced complete all as specified and directed and removing debris outside MD land complete all as specified and as directed by Engr-in-Charge

M&L for PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete and like etc including demolition of cement concrete in ground floor & paving, n. exc 15 cm thick (below or above GL), unreinforced complete all as specified and directed and removing debris outside MD land complete

M & L for 75mm thick cement concrete (1:2:4) type B-2, using 40mm graded stone aggregate as in plinth protection and finishing the surfaces even and smooth without using extra cement, including necessary expansion joints, filled solidly with a hot mixture of blown grade bitumen and sand 1:1 by weight including Demolition of cement concrete in ground floor & paving, n. exc 15 cm thick (below or above GL), unreinforced complete all as specified and directed and removing debris outside MD land complete

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and Old unserviceable of any height complete all as specified and as directed by Engr-in-Charge.

M & L for mild steel TMT bars 6 to 10 dia as in stirrups, spaces and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed by Engr-in-Charge.

M&L for providing reinforced cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in kitchen slab,landing, Chajja or in any position including Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for and including reinforcement required to facilitate demolition upto and including fourth story and on the roof top/mumty/parapet and removal of debris and rubbish out side MoD land complete all as specified and directed.

Providing and fixing special water tight centering and shuttering including bolting, strutting, propping etc. so as to withstand a pressure of 0.1 Mpa including removal of form from all locations including beams, columns, slabs, walls, foundations, footings, landings, stairs, balconies etc. complete all as specified and as directed by Engr-in-Charge.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles and removing debris out side MD land complete all as specified and directed by Engg-in-charge.

M & L for brick work in CM 1:4 using Sub class ‘B’ Bricks straight or curved on plan any radius in half brick thick wall complete all as specified and directed.

M & L for Except Brick work with sub class 'B' bricks, straight or curved on plan, exc 6 mtr mean radius, built in CM 1:6 complete all as specified and directed by Engg-in-charge.

M & L for Brick work with sub class 'B' bricks, straight or curved on plan, exc 6 mtr mean radius, built in CM 1:6 complete all as specified and directed by Engg-in-charge.

M&L for rendering 10 mm thick plastering in cement mortar 1:3 as in ceiling finished even and smooth without using extra cement to match with existing surface including taking down cement plaster including all necessary scafffoldingcomplete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair face of brick work/ concrete surfaces (either surfaces) of wall and finished even and smooth without using extra cement including Taking down cement plaster of any description from brick wall surfaces etc including racking out joints and hacking for key, scrubbing down with water etc including all necessary scaffolding arrangments of any height complete all as directed.

M&L for rendering 15mm thick rendering in cement mortar 1:4 on fair face of brick work/ concrete surfaces of wall with water proofing admixture finished even and smooth without using extra cement (WPC will be measured and paid separatly) including Taking down cement plaster of any description from brick wall surfaces etc including racking out joints and hacking for key, scrubbing down with water etc including all necessary scaffolding arrangments of any height complete all as directed.

Supply only liquid water proofing compound complete all as specified and directed.

Taking down Chowkhats or frames n.exc 1.50 sqm each (without taking off shutters from the frames) complete all as specified and as directed by Engr-in-Charge

Taking down Chowkhats or frames, exc 1.50 sqm but n exc 4.00 sqm each (without taking off shutters from the frames) complete all as specified and as directed by Engr-in-Charge.

Taking down shutters of any description n exc 1 sq. m each complete all as specified and directed.

Taking down shutters of any description exc 1 sq. m and n exc 2 sqm each complete all as specified and directed.

Supplying and fixing factory made single extruded WPC (Wood Polymer Composite) solid door Frames/Chowkhat comprising of 100 mm X 50 mm size, applying PVC solvent cement and screwed with full body threaded, star headed SS screws having minimum frame density of 750 kg/cum and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and as directed by Engr-in-Charge

S & F factory made single extruded WPC (Wood Polymer Composite) solid door Frames/Chowkhat comprising of 125 mm X 65 mm size applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and as directed by Engr-in-Charge

S & F factory made single extruded WPC (Wood Polymer Composite) solid door Frames/Chowkhat comprising of 45 x 70 mm size applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and as directed by Engr-in-Charge

S & F factory made 28-30 mm thick single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size, modulus of elasticity 850 N/mm” and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and as directed by Engr-in-Charge.

M & L for 2nd class 30 mm thick Plain, framed,panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats all as specified and directed by Engr in Charge.

S&F 35mm - 30 mm thick flush shutter, solid core construction with block board core and both side with different colours, matt finish of wooden colour solid panel, commercial type on both side complete all as specified and as directed by Engr-in-Charge.

S&F 2nd class hard wood plain,solid, straight chowkhat and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joint complete all as specified and directed.

S & F 35mm thick 2nd class hard wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc(without sash bars) edges of framing plain, chamfered or rounded, fittted with cut and mitred beads for securing gauge,etc sizes of member of shutter as specified SSR part-I Section 8 clause 8.24 (b) and fitted to chowkhats complete all as specified and as directed by Engr-in-Charge

S & F factory made 40 mm thick flush door shutter, solid core construction with block board core and ply wood face panels , both side covered with decorative face laminate incl 5mm thick teakwood lipping alround with centrally locking arrangement with Lock of make Godrej of Link, 7 lever and Self closing Device complete all as specified and as directed by Engr-in-Charge.

Providing and fixing factory made UPVC white/any colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+-0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+-0.2mm thick galvanised steel Frame (30mm x 18mm) 2 Nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm, including 5 mm thick glass and required including taking down of existing windows of any description or any size

Supply and fixing factory made UPVC white colour Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension (Area of window upto 0.75 sqm.) comprising of UPVC multi chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to UPVC profile), UPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass shall be paid separately) Note: For UPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made including taking down of existing windows of any description or any size

Supply and fixing factory made UPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of UPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to UPVC profile), UPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). Note: For UPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made including taking down of existing windows of any description or any size

M&L for powder coated Anodised aluminium frame for doors, windows, ventilators, partition walls etc with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S & F sheet glass, ordinary quality, 5.5 mm thick and glazed with oil putty or fixed with rubber beading, in square not exceeding 0.5 Sqm in each pane omplete all as specified by Engr-In- Charge.

S & F of aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples omplete all as specified by Engr-In- Charge.

S & F powder coated anodised aluminium grill of 50x50x5 mm size of approved design/pattern with approved section and fixed to the existing window with stainless steell screws @ 200 mm C/C including the grill for operatiing handles and fixing all as specified and as directed.

Supply & fix 150 mm length aluminium anodised barrel tower bolt extruded section complete all as specified and directed.

Supply & fix 150 mm long aluminium handles, cast type, anodised complete all as specified and directed.

Supply & fix 300mm long aluminium alloy, anodised sliding door bolt with haps, staple(bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S & F stainless steel butt hinges, heavy duty of 100mm size complete all as specified and as directed by Engr-in-Charge.

Supply & fix 150 mm length stainless steel anodised barrel tower bolt extruded section complete all as specified and directed.

Supply & fix 150 mm long stainless steel handles, cast type, anodised complete all as specified and directed.

Supply & fix 300mm long stainless steel sliding door bolt with haps, staple(bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S & F stainless steel hasps and staples, type -1, safety type, size 100 mm, anodized finish, not be less than Grade AC 10 of IS 1868 : 1996 including fixing with screws complete all as specified and directed by Engg-in-charge.

S & F aluminium alloy hasps and staples, type -1, safety type, size 100 mm, anodized finish, not be less than Grade AC 10 of IS 1868 : 1996 including fixing with screws complete all as specified and directed by Engg-in-charge.

S & F of 20 mm dia stainless steel fancy type curtain rod with and including stainless steel fancy type brackets/ Nobs and side fancy type caps, stops, in suitable size and necessary rings, side caps etc. complete all as specified and directed.

S&F Steel windows with side hung shutters incl box type hinges with steel handles and steel peg stay complete with glazing bars dovetailed or welded complete all as specified and directed.

S&F Steel windows with side hung shutters incl box type hinges with steel handles and steel peg stay complete without glazing bars dovetailed or welded complete all as specified and directed.

S&F in repair for providing factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick with particle board core (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face supplying & fixing in frame at site as per specification & drawing

S&F in repair for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification of drawing complete all as specified and directed.

S & F in repair for Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification of drawing complete all as specified and directed

S&F in repairs for factory made Pre-laminated/plain/PVC shutter of 9mm (+-0.7) thickness consisting of panel of 9 mm (+-0.7) thick celuka ply of density 600 Kg/Cbm manufactured by an ISO-9000 certified company using for back side shutter celuka ply 9 mm (+-0.7) thick cut in desired size of shutter and fixed with the frame of kitchen accessory etc complete as direction of GE, manufacturer's specification and drawing complete all as specified and directed.

S&F in repairs for factory made Pre laminated/plain/PVC shutter of 18 mm (+-0.7) thickness consisting of panel of 18 mm (+-0.7) thick celuka ply of density 600 Kg/Cbm manufactured by an ISO-9000 certified company using for shutter celuka ply 18 mm (+-0.7) thick cut in desired size of shutter and fixed with the frame of kitchen accessory at all four edges of shutter using 13/6 size self tapping steel. The thickness of the shutter is edge lipped by 18 mm width x 1 mm thick PVC sheet using solvent cement etc. including stainless steel handle, tower bolt, magnet etc complete as direction of GE, manufacturer's specification and drawing complete all as specified and directed.

M&L for fixing of magnet suitable for cupboard shutters, shelfs etc complete all as specified and directed.

S&F in repair stainless steel bascket cutlurry size-15"x20"x4" (width may be vary as per site contion from 15" to 21") incl powder coated drawer runner/channel and soft close as required complete all as specified as per manufaturer instruction (PVC shutter/board paid seperately).

S&F in repair stainless steel bascket plain size-15"x20"x6" (width may be vary as per site contion from 15" to 21") incl powder coated drawer runner/ channel as required complete all as specified as per manufaturer instruction.

S&F in repair stainless steel bascket for thali size-15"x20"x8" (width may be vary as per site contion from 15" to 21") incl powder coated drawer runner/channel as required complete all as specified as per manufaturer instruction.

S&F in repair stainless steel bascket for plate size-15"x20"x6" (width may be vary as per site contion from 15" to 21") incl powder coated drawer runner/ channel as required complete all as specified as per manufaturer instruction.

S & F 30 mm wide Continuous (piano) hinges,mild steel, bright finish or electrogalvanised all as specified and directed by Engr in charge

S& F Aluminium (extruded section body) Door closer hydraulically regulated,designation No. 3,universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed by Engr in charge

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed by Engr in Charge

S&F in repairs Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed by Engr in Charge

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed all as specified and directed by Engr in charge

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with bead for exc 1.5 m all as specified and directec by Engr in Charge

S &F 3 mm Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane all as specified and directed by Engr in Charge

S&F 3 mm Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane all as specified and directed by Engr in charge

Taking down wall/ceiling boards Asbestos plywood of any thickness including cover fillets complete all as specified and directed.

M&L for Providing and fixing tiled false ceiling of designer tiles (high pressure steam Cured) of 4mm thickness (as per IS:14862) of size 595x595mm and any one of the design in true horizontal level, suspended on inner locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grms, both side inclusive and black painted groove on all T webs) consisting of main “T” runner with suitably spaced joints to get required length and 15x32mm made from 0.3mm thick sheet, 1200mm long spaced between main “T” at 600mm C/C to form a grid of 1200x600mm and secondly cross “T” of length 600mm and size 15x32mm made of 0.30mm thick sheet to be interlocked at middle of 1200x600mm panel to form grids of 600x600mm and wall angle 15x20x0.36mm and laying false ceiling tiles in the grid including, required cutting / making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanized butterfly level clips, spaced at 1200mm c/c along main “T”, bottom exposed width of 15mm of all “T” sections shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5 mm width, all complete at all heights as per directions of EIC.

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of ted perforated 12mm Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 4 76 (Part 4) -1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of mainT runners of size 15x32 mm of length 3000mm, cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600x 600mm (having filled with black silicaon), suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in Charge.

M&L for providing and fixing 10 mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface with GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre with & incl Hangers 4mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long for any sunk or raised moulding complete all as specified & directed.

M & L for 8/10mm thick PVC ceiling (any colour OR pattern) with aluminium frame work for receiving ceiling boards, including all aceessoreis for fixing at variuos levels complete all as specified & directed.

S&F in repairs PVC tensile fabric structure with PVDF (polyvinyl-idene-fluoride) coating with all necessary fixtures, of any size and shape for making canopies, shed fixed with mild steel structural frame work, weight of the fabric is considered, with fabrics ranging from 900 gsm to 1200 gsm all as specified and directed. Note : (a) The shape/ design of the sheds will be as approved by GE. (b) Cost of structural steel used will be measured and paid separetly under relevant items in this schdule.

S&F in repair 12mm thick, toughened glass clear or frosted for door shutters, partitions, shelves etc including fitting and fixtures such as glass handles SS studs, fittings for door pivots etc complete all as specified and directed.

S&F in repair for 12 mm thick plywood, grade BWP type BB fixed with brass screws and cups to timber frame work complete all as specified and directed : sample as approved by GE

S&F in repair for 2 mm thick veneered designer natural wood grain sheet fixed with adhesive as per manufactrue instruction to plywood work complete all as specified and directed, sample as approved by GE

S&F in repair for Plain fillets of second class hard wood, square or rectangular in section, clean sawn, wrought, secured with nails or brads; sectional area exceeding 6 Sqcm but not exceeding 13 Sqcm complete all as specified and directed. sample as approved by GE

SS&F in repair PVC sheet wall panelling of thickness 5mm (+0.25) consisting of panels of desired size stuck on inner frame work of 50mm wide strip of 5mm (+0.25) thick prelam PVC sheet. The panel and strip shall be of 600kg per cum density manufactured by ISO 9000 certified company. The strip should have in their centre agrove of 6mm width and 1mm depth for sinking the head of the screw used to fix the strip to the wall vertically at an equal interval of 10 inch between to PVC strips complete all as specified and directed.

Dismantling old asbestos sheets of any description, any location complete all as specified and directed.

S&F Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc all as specified and directed by Engr in charge

S&F Pre-painted galvalume aluminium zinc coating GI based trapezoidal profile roofing sheets 0.50 mm thick of any colour / length having tensile strength of 550 MPA AZ-150 as in roof coverings/cladding having effective & overall width 1015 mm &1072 mm respectively, profile hieght 28.5 mm and centre to centre distance between ribs 203 mm fixed with self tapping screws as directed by manufacturer on wooden/steel members including steel scaffolding of any height complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheets 0.50 mm thick of any colour/length having tensile strength of 550 MPA AZ-150 as in roof coverings/cladding having effective & overall width 1015 mm &1072 mm respectively, profile hieght 28.5 mm and centre to centre distance between ribs 203 mm fixed with self tapping screws as directed by manufacturer on wooden/steel members including steel scaffolding of any height complete all as specified and directed.

Dismantling unframed timber scantlings 40 sq. cm and over in section, in any position

Dismantling structural steel work including doors, gates but excluding framed truss etc.

S&F joint, channel, angle, tee sections, & MS flats fixed independently, without connection plate, etc. (cut to ordinary lenghts i.e. within 20mm of the length indicated) for purlins fixed to wooden rafters and all other similar works conforming to Fe 410-W (Gde-E-250) quality-A including dismantling Old unserviceable existing wrought iron work complete all as specified and directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to FE.290.Gde-E-165 all as specified and directed by Engr in Charge

S &F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410-W (Gde E- 250) quality A all as specified and directed by Engr in Charge

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161 1979 grade St.-24 all as specified and directed by Engr in Charge

Welding in repairs exc 20 mm and n. exc 2.5 cm in length all as specified and directed

S&F in repairs 18/19 mm Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work all as specified and directed by Engr in charge

M&L for roof treatment with polymeric membrane (APP based) with non woven polyester mat as reinforcement with following:- (a) M&L for surface preparation by removal/taking down of existing treatment of tar felt/tiling/loose particle to ensure or clean smooth and dry surface and preparing the surface. (b) M&L for providing & laying a coat of cold applied bitumen 85/25 based primer on entire surface @ 0.30 Ltr/Sqm on dry and clean surface. (c) M&L for providing & laying APP based polymeric membrane of 3 mm thickness of weight of 3.0 Kg/Sqm with non woven polyster fiber as reinforcement on primed surface by torch application with side over laps & joints over laps etc as per manufacturers instruction. (d) M&L for finishing of top surface by two coat of aluminium paint over a coat of blown bitumen 85/25 grade @ 1.2 Kg/Sqm grouted all as specified and as per manufacturers instruction. (e) M&L for providing test with filling of water over roof slab continuously for 48 hours all as specified and directed. (f) M&L for providing template of size 450 x 450 mm to each bldg where roof treatment is carried out with marking CA No, date of roof treatment, expiry date, etc all as specified and directed.

M&L for providing, cement concrete type B0 1:2:4 (12.5 graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 mixed with WPC on roof surfaces finished even & smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured & paid separately.

Taking down cement plaster on brick or stone walls, including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by the Engr-in-Charge.

Material and labour for 5 mm thick plastering in CM With Nano fiiler 1: Cement 1: Sand 3 on concrete surfaces as in sides of column, lintel, beam, chajja, facia, railing, RCC wardrobe etc including finish the surface even and fair without using extra cement complete all as specified and as directed

Material and labour for 20mm thick plaster in cement mortar with Nano wall filler 1: cement 1: sand 4 in two layers, i.e 10mm thick in each layer, top layer mixed with integral water proofing liquid admixture as per manufacturers instruction on brick or concrete surfaces of wall finished the surface fair and even complete all as specified and as directed. Note :- WPC shall be measured and paid separately.

Material and labour for rendering 15mm thick in cement mortar with Nano wall filler 1: cement 1: sand 6 on fair faces of brickwork or concrete surfaces, finished the surface even and smooth without using extra cement complete all as specified and as directed.

Supply only Nanotechnology based Elastomeric Hydrophobic Powder/admixture (EHP) powder for cement plaster and concrete.

Material and labour for exposing cracks more than 1mm wide with tile cutter and foming V groves nex 10mm wide and 10 mm deep in INSIDE RCC roof and filling Nanotechnology based Anti- corrosive with high strength Carbon fiber based Shorter chain epoxy Coating Perocess: a) Clean the Surface and open the crack and apply nano base Bond coat b) Mix with Nano wall filler with Bond coat and Fill the crack c) Apply Final Bond coat in the cracked surface Note : 1. Rate shall include for making surface clean,dustfree, dry, and free of wax, grease, oil, loose or peeling particle, and other foreign materials. 2. During application ambient temperature is preferred. Frost, fog, or damp conditions should be avoided.

Material and labour for exposing cracks more than 1mm wide with tile cutter and forming V-grooves nexc 10mm wide and 10mm deep in RCC roof and filling with Nanotechnology based Anti-corrosive with high strength carbon Fiber based shorter chain Epoxy coating (Bond Coat) of finest quality, high strength, high penetration, durable, UV resistant, high scratch/ impact resistant, bacteria resistant and thermally stable, Semi transparent, mixed in proportion (4 Base : 1 Hardner) with Nano based Wall filler @ 1 Bond coat : 1.5 Wall filler in reqd consistency complete all as specified. Note : 1. Rate shall include for making surface clean,dustfree, dry, and free of wax, grease, oil, loose or peeling particle, and other foreign materials. 2. During application ambient temperature is preferred. Frost, fog, or damp conditions should be avoided.

Material and labour for providing plain cement concrete with Nano filler 1: cement 1; sand 2: agregate 4 type B1 using 20mm graded stone aggregate as in roof padding laid in slope as per requirement mixed with integral water proofing liquid admixture as per manufacturer's instructions complete all as specified and as directed. Note : (i) Minimum thickness of PCC shall be 30mm. (ii) Integral water proofing liquid admixture shall be measured and paid separately under appropriate item here in after (ii) PCC shall be laid to acheive true slope towards the drain/weep holes.

Material and labour for applying a coat of Nano technology based water proofing compound (1 part powder : 1 part liquid), of desired consistency with nylon brush @ 5 sqm/kg coverage over vertical/horizantal surface of RCC roof and parapet complete all as specified.

M&L Water Proofing: a) Surface Preparation - Mild Chipping of the surface, Clean the Surface with Nano Bio wash. b) If onlinr leackage found seal with Nano magic and apply nano Bond coat.Open the cracks by making ‘V’ groove, filling cracks with Nano Crack Filler. c) Aplly Nano carbon baesed shorter chain Nano Bond Coat d) Providing and applying Nano Water Base Water Proof compound one coats after surface preparation using brush, not containing toxic materials like Pb, Cr, Zn; having defect-free nano-particles with inhibiting characteristics having bacteria killing rate above 98% and anti-fungal properties, with super-hydrophobic properties with contact angle of water more than 75degree , permeable type with elongation (stretch ability) of more than 300%, in a nano-structured self assembled dispersion system with VOC level of less than 1% , 60 micron DFT. e) If ant crack found open and fill the crack with nano carbon base filler and bond coat.and use nano wall filler to reduce the undulation. f) Apply Nano high penetration Bond coat two coat. g) Providing and applying Nano Barrier Coat Paint/ Nano Water Base Water Proof Paints 2 coats over screed concrete using brush, not containing toxic materials like Pb, Cr, Zn; having defect-free nano-particles with inhibiting characteristics having bacteria killing and anti-fungal properties, with super-hydrophobic properties with contact angle of water more than 750 , with elongation (stretch ability) of more than 300%, in a nano-structured self assembled dispersion system with VOC level of less than 1% , 60 micron DFT per coat.

Demolition of Cement Concrete of any description and in any position not otherwise specifically provided complete all as specified.

M&L Water Proofing: a) Surface Preparation - Mild Chipping of the surface, Clean the Surface with Nano Bio wash. b) If onlinr leackage found seal with Nano magic and apply nano Bond coat.Open the cracks by making ‘V’ groove, filling cracks with Nano Crack Filler. c) Aplly Nano carbon baesed shorter chain Nano Bond Coat d) Providing and applying Nano Water Base Water Proof compound one coats after surface preparation using brush, not containing toxic materials like Pb, Cr, Zn; having defect-free nano-particles with inhibiting characteristics having bacteria killing rate above 98% and anti-fungal properties, with super-hydrophobic properties with contact angle of water more than 75degree , permeable type with elongation (stretch ability) of more than 300%, in a nano-structured self assembled dispersion system with VOC level of less than 1% , 60 micron DFT. e) If ant crack found open and fill the crack with nano carbon base filler and bond coat.and use nano wall filler to reduce the undulation. f) Apply Nano high penetration Bond coat two coat. g) Providing and applying Nano Barrier Coat Paint/ Nano Water Base Water Proof Paints 2 coats over screed concrete using brush, not containing toxic materials like Pb, Cr, Zn; having defect-free nano-particles with inhibiting characteristics having bacteria killing and anti-fungal properties, with super-hydrophobic properties with contact angle of water more than 750 , with elongation (stretch ability) of more than 300%, in a nano-structured self assembled dispersion system with VOC level of less than 1% , 60 micron DFT per coat.

M & L for PCC (1:5:10) type E2 using 40mm graded stone aggregate in foundations, filling and mass concrete, sunken floors complete all as specified and directed.

Material and labour for appplying NANO magic in sealing floor traps, waste pipes outlets from wall, etc

Material and labour for appplying NANO magic in sealing floor traps, waste pipes outlets from wall, etc

Preparation of new plastered surface or old treated surface of wall by applying 2mm thick wall care putty and making the surface smooth and applying two coat of oil emulsion distemper over one coat of primer using roller for painting complete all as specified & directed.

M&L for preparing plastered new surfaces of ceiling and applying three coats of white wash on ceiling surface

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new/old surfaces.

M&L for prepration of old decorated surfaces of walls inluding cornices etc by brooming down or steel wire brushing scrapping down smoke soot moulds moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash complete all as specified and direted

Material & Labour for complete removal of existing treatment of walls by washing down and smoothing old surface of walls, prerparation of surface and applying two coats of interior oil bound distemper with smooth roller finish over 2 mm thick putty and a coat of primer ,complete all as specified and directed.

M& forL finishing walls with textured interior paint with base and oil putty of any design/shade : old decorated surface of wall by removing existing treatment with mechanical sander (two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of interior primer applied @ 2.20 Kg/Sqm incl all material all as specified and directed

M&L for PVC 3D Decorative various pattern modern style 5-6 mm thick water proofing wall paper before complete removal of existing treatment by scrapping with mechanical wall sander having cart part Trucare series H-01 with variable speed control 1500-2700 RPM (having mechanical vacuum mechanism) sanding padof 180 mm having dia of 7"/9" to make the surface free from dust, loose paint etc by skilled labour fixing on wall using top guard glue adhesive fixed all as soecified 7 directed. Note : Wall paper shall be approved by GE

M&L for preparation of old decoraetd surfaces of walls incl cornices etc by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and sfflorescent salts and trading oil and greasy spots and applying two coat of cemen base paint complete all as specified and directed

M&L for preparation of old painted steel and iron surface of any description exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

M&L for preparation of old painted surface of wood and wood based surface by knotting, stopping etc of any description exc 10 cm width or gith and applying one coat of synthetic enamel paint complete all as specified and directed

M&L for preparation of old surfaces of wall by washing, rubbing down and stopping of distembered and applying one coat of oil bound distemper on wall including curing complete all as specified and directed.

Material and labour for preparation of old decorated surfaces of walls including brooming down or steel wire brushing, scrapping down smoke, soot, moulds, moss and efflorescent salts and trading oil, greasy spots and apply two coat distemper oil emulsion on walls complete by an authorised applicator complete all as specified and directed

Material and labour for preparation of old painted ceiling surfaces and applying two coat of white wash on ceiling complete all as specified and directed

Material and labour for preparation of new wooden surfaces of any description, not otherwise described,over 10 cm width or girth and applying two coats of synthetic enamel paint (ordinary paint tint) (each coat) over a coat of pink primer including scafoldings of any hieght complete all as specified and directed.

M & L for preparation of newly steel and iron surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

M&L for dark shade vitrified tiles, first quality, conforming to IS-13006/EN/176 group B1a, 8, to 10mm thick, (square/ rectangular) polished, area of each tiles exceeding 0.42 Sqm and not exc 1.00 Sqm, in flooring, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including 15mm thick screed bedding/plaster in cement mortar (1:6) including dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish out side MD land complete all as specified and as directed by Engr-in-Charge.

M&L for dark shade, vitrified tiles, first quality, conforming to IS-13006/EN/176 group B1a, 8, to 10mm thick, (square/ rectangular) polished, area of each tiles exceeding 0.42 Sqm and not exc 1.00 Sqm, in vertical set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including 15mm thick screed bedding /plaster in cement mortar (1:6) including dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish out side MD land complete all as specified and as directed by Engr-in-Charge.

M & L for dark shade, double/ultra charged vitrified tiles, first quality, conforming to IS-13006/EN/176 group B1a, 8, to 10mm thick, (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm , in flooring, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including 15mm thick screed bedding in cement mortar (1:6) including dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish out side MD land complete all as specified and as directed by Engr-in-Charge.

M & L for dark shade, double/ultra charged vitrified tiles, first quality, conforming to IS-13006/EN/176 group B1a, 8, to 10mm thick, (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm , in vertical set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including 15mm thick screed bedding /plaster in cement mortar (1:6) including dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish out side MD land complete all as specified and as directed by Engr-in-Charge.

M & L for non skid coloured ceramic tiles, joint free, conforming to IS-13755, group B II(b) , 1st & premium quality, Digital coloured ceramic tiles, 300mm x 300mm x 6-7 mm thick in floors, shelves etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed of 15mm thick in CM (1:6) including dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish out side MD land complete all as specified and as directed by Engr-in-Charge.

M & L for glazed coloured ceramic tiles conforming to IS-13755, group B III , 1st & premium quality, Digital coloured ceramic tiles, 600mm x 300mm or 450x300x 6-7mm thick in vertical surfaces (including designed borders ) such as skirting and dados, set and jointed in neat cement slurry pointed in coloured cement to match over rendering 10 mm thick on fair faces of brick work in CM (1:4) including dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish out side MD land complete all as specified and as directed by Engr-in-Charge.

M&L for HI-Gloss digital ceramic tiles tiles in vertical surface of size 600mm x 1200mm 8 to 10 thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including rendering 10 mm thick on fair faces of brick work in CM (1:4) including dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish out side MD land complete all as specified and as directed by Engr-in-Charge.

Demolition of cement concrete in paving, in any thickness and description, unreinforced in any position complete all as specified and directed and removing debris outside MD land complete all as specified and as directed by Engr-in-Charge

M&L for glazed/matt finish chequred cement concrete coloured tiles of area exc 0.09 Sqm but not exc 0.36 Sqm and 25 mm thick, set, jointed and pointed in neat cement slurry (with gray cement and pigment) after and including 20 mm thick in cement plaster in CM (1:6) for fixing tiles complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness laid in floors, aprons etc, laid, bedded and pointed in any mortar and and removing the rubbish outside MD land complete all as specified and as directed by Engr-in-Charge

M & L for machine cut kota stone slab flooring 16 to 18 mm mm thick, over cement screed base laid 15 mm thick in cm 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to mirror finish complete all as specified and as directed by Engr-in-Charge

M & L for machine cut Kota stone slab flooring,16 to 18 mm mm thick, in one piece as in vertical surfaces, skirting etc, set and jointed in neat cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and pointed in colour cement to match including backing coat 10 mm in CM (1:3) complete all as specified and as directed by Engr-in-Charge.

M & L for Granite (of any type and colour) , 16 to 18 mm thick machine cut, set, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete including screed bed in cement plaster 20 mm thick 1:4, as in kitchen platform, jamb/cill of window, ventilator, border, flooring and simillar work etc complete all as specified and as directed by Engineer-in-Charge.

S&F in repair for 3.2 to 3.3 mm Linoleum, plain coloured, laid dry in floors including stretching, cutting and fitting is sealed down with an approved adhesive all as specified and directed by Engr in Charge

S & F in repairs steel water tubing of size 15mm bore, medium grade, galvanised iron with all Fittings such as Tees, elbows, sockets, bends, unions, shortpieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239, fixed to wall and ceiling or laid in floors and making good disturbed surfaces to match the existing surfaces complete all as specified and as directed by Engr-in- Charge.

S & F in repairs steel water tubing of size 20 mm bore, medium grade, galvanised iron with all Fittings such as Tees, elbows, sockets, bends, unions, shortpieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239, fixed to wall and ceiling or laid in floors and making good disturbed surfaces to match the existing surfaces complete all as specified and as directed by Engr-in-Charge.

Cutting chases, pinning in making good to facing on brick walls where required and pointing in cement mortar (1:3) to ends for concealed water tubing and making good ,cutting n, exc. 10cm girth complete all as specified and as directed by Engr-in-Charge.

S & F in repairs vitreous china wash down, white, water closet pan (pedestal pattern) with 'P' of 'S' trap (of size 465mm x 355mm x 265mm), including plastic seat cover to match with colour of WC, closed pattern with flat bottom & cover and chromium plated mild steel or aluminium anodized hinging device including connecting to trap and flushing pipe, anti-syphonage pipe etc and screwed with brass screws to sheesham wood plugs embedded in floor complete all as specified and directed by Engineer-in-Charge.

S&F in repair wash hand basin table top of size Table Top Basin 565x425x140 vitrous China including , waste coupling & PVC waste pipe of 32 mm dia etc. complete all as specified and directed.

S&F in repair wash hand basin table top of size Table Top Basin18 x 13 x 5 inches vitrous China including , waste coupling & PVC waste pipe of 32 mm dia etc. complete all as specified and directed.

S & F in repairs 10 litres capacity, premium Push Button Type Flushing Cistern Dual 10 LTR Cistern low level slim, syphonic type, white, plastic flushing cistern as per IS 7231: 1994 with inlet, ball valve float vavle and other connected accesories including brackets and 40 mm nominal dia high density polyethylene pipes for flush pipe complete all as specified and as directed by Engr-in-Charge.

S & F in repair 15 mm bore, fancy type, angular valve, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed by Engr-in-Charge.

S & F in repair 15 mm bore, fancy type, concealed stop cock (regular body) cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed by Engr-in-Charge.

S & F in repair brass chromium plated ,15 mm bore, fancy type, sink cock( wall mounted) with 150mm long swell spout, wall flange and provision of WP connection, cast copper alloy with fancy type, chromium plated, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engr-in-Charge.

S & F in repair 15 mm bore, fancy type, bib taps, long body (two in one) cast copper alloy 15mm bore with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engr-in-Charge.

S & F in repair 15 mm bore, fancy type, bib taps, long body, cast copper alloy, 15mm bore with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engr-in-Charge.

S & F in repair for 15 mm bore, fancy type, wall mixer with 115 mm long bend pipe for connection to overhead shower (with bush and piston Divertor fittings) with aerator complete all as specified and as directed by Engr-in-Charge.

S & F in repair 15 mm bore, fancy type, health faucet with SS hose complete all as specified and as directed by Engr-in-Charge.

S & F in repair fancy type, CP, Towel Rail, 61 cm long complete all as specified and as directed by Engr-in-Charge.

S & F in repair CP Towel Ring complete all as specified and as directed by Engr-in-Charge.

S & F in repair CP, soap dish complete all as specified and as directed by Engr-in-Charge.

S & F in repairs sheet glass corner shelf assembly consisting of 5.5 mm thick sheet galss shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and as directed by Engr-in-Charge.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S & F 15 mm bore overhead shower 250 mm dia single flow (ABS body chrome plated with grey face plate) with rubit cleaning system including shower arm 381 mm long (cat part No-SA 106 /108 Of ESS ESS Croma) Square shape with wall flange complete all as specified and as directed by Engr-in-Charge.

S & F in repair 15 mm bore Single lever basin mixer extended body without pop-up waste system with 450 mm long flexible hose screwed down, fancy type high pressure, with or without lettered 'HOT or COld unserviceable' with long screwed sunk and fly nuts complete all as specified and as directed by Engr-in-Charge.

S&F in repairs for stainless steel Robe hook 2-way thick complete all as specifed.

S&F in repair in brass chromium plated towel rack with 3 hooks complete all as specified.

S&F in repairStainless Steel Double Bowl Kitchen Sink made of stainless steel 1 mm thick 304 grade kitchen or laboratory with plugs, washers and waste pipe including bedding in cement morter to dwarf wall or including fixing cantilever brackets and connecting union to pipe

S & F in repairs Stainless steel kitchen plate rack made out of 0.63mm thick stainless steel sheet of size 750x600mm including all fixing screws , rack hooks, etc and attachments, design of plate rack to be approved by the Engineer -In - Charge and as specified.

S & F of 18mm thick Marine Plywood as per IS 710, laminated of any colour with High glossy acrylic sheet of 3mm thick , grade I , for frame and shutter for kitchen cabinets complete all as specified and directed by Engr-in-charge and reuse as directed by Engr in Charge.

S & F of 200mm length Brass handles, cast type, polished brigh complete all as specified and directed by Engg-in-charge

S & F in repairs 110 mm dia PVC (SWR) pipes, type B, single socketed in any length with rubber ring joints, sealed with adhesive suitable for PVC pipes and fixed to walls including stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays upto 04 storeys including all steel scaffloding arrangments complete all as specified and directed by Engg-in-charge.

S & F in repairs 75 mm dia PVC (SWR) pipes, type B, single socketed in any length with rubber ring joints, sealed with adhesive suitable for PVC pipes and fixed to walls including stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays upto 04 storeys including all steel scaffloding arrangments complete all as specified and directed by Engg-in-charge.

S & F in repairs 75mm dia PVC (SWR) bends with access doors, any radius, at any height including steel scaffOld unserviceableing complete all as specified and directed by Engg-in-charge.

S & F in repairs 110mm dia PVC (SWR) bends with access doors, any radius, at any height including steel scaffOld unserviceableing complete all as specified and directed by Engg-in-charge.

S & F in repairs 75 mm dia PVC (SWR) junction single, (single T) equal or uequal, with access door at any height including steel scaffOld unserviceableing complete all as specified and directed by Engg-in-charge.

S & F in repairs 110 mm dia PVC (SWR) junction single, (single T) equal or uequal, with access door at any height including steel scaffOld unserviceableing complete all as specified and directed by Engg-in-charge.

S & F in repairs 75 mm dia PVC (SWR) vent cowl, at any height including steel scaffOld unserviceableing complete all as specified and directed by Engg-in-charge.

S & F in repairs 110 mm dia PVC (SWR) vent cowl, at any height including steel scaffOld unserviceableing complete all as specified and directed by Engg-in-charge.

S&F in repairs cover for HDPE water tank of capacity 500/1000 ltrs rotating type including frame including nut bolt complete all as specified and directed.

S&F in repairs CP grating any type 125 mm dia fixed over floor/nahani trap (with hole/without hole) complete all as specified.

Supply and fix in repair 500 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and directed.

Supply and fix in repair 1000 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and directed.

Cleaning of HDPE tank of capacity up to & including 500 Litres by Flushing out water cleaning & removing of sludge, scale mud etc from wall & floor by rubbing with brushes, cleaning with caustic soda etc complete & finally washing with fresh water, including writing date of cleaning with white synthetic enamel paint and removing sludge, scale mud etc to a distance not exceeding 50 metre and depositing complete all as directed.

All as per item No.183 here-in-before but capacity of tank exc 500 litre but not exc. 1000 litres

S&F in repair 15 mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed

S&F in repair 20/25 mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed

S&F in repairs 40 mm Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm 45gms/40mm-60 gms) all as specified and directed by Engr in Charge

S&F in repairs Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) all as specified and directed by Engr in Charge

S & F in repairs PVC connections 15mm size with PTMT nuts of length 300/450mm all as specified and directed by Engr in Charge

S&F Floor door stopper of aluminium alloy body and tongue, oveall length 150 mm anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed

S&F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed

M&L for taking down and resecuring or easing & adjusting, shutters of any description, exc 1.00 sqm but not exc 2.00 sqm complete all as specified and directed. Note :-Refixing' includes taking down, easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc.

S&F rubber door cill 40/50mm as required in door cill complete with required nails etc complete all as specified and directed.

M&L for any coloured digital ultra strong / heavy duty outdoor anti skid vitrified tiles 15 mm thick (Square / Rectangular) polished area of each tile exc 0.09 Sqm and not exc 0.36 sqm, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles and including 20 mm thick screed bed of cement mortar in CM (1:6) for fixing tiles complete all as specified.

Please Enable Macros to View BoQ information