PROVN OF KOTA STONE FLOORING IN LIEU OF PCC FLOORING IN PAINT STORE LOGISTICS COMPLEX AND CERTAIN SANCTIONED WORKS UNDER GE NW KOCHI AT NAVAL BASE KOCHI

Amount

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water any description, etc.

Dismantling floor hearth or wall tiling including cement mortar bedding removing serviceable tiles to store & rubbish off the premises complete all as specified.

Demolition of plain cement Concrete of any description and in any position not otherwise specifically provided for

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required

M&L for providing PCC 1:3:6, type C1 (using 20 mm graded stone aggregate) as in cills, steps, parapets and railings, copings, bed plates etc including necessary form work complete all as specified

M&L for pre-cast cement concrete block masonry in Type C1, 1:3:6 (20mm graded aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified

Taking down chowkats or frames with shutters (without taking off shutters from frames) n exc 1.50 sq. m each all as specified and directed

S&F stainless steel wire cloth, 0.36mm nominal dia or wire and average width or aperature 1.40mm, fixed with stainless steel wire staples complete.

M & L framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified

M&L framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-410-W

M&L mild steel angle iron posts and wind ties including welding to raise the height of existing posts, securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified

M&L mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exc 10cm but not exc 15cm long and dia of neck 11 to 15mm complete all as specified

S&F galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

S&F for anodised aluminium frame work for doors, windows, ventilators, partitions and cubicals with one or more rebates including joining cleat for fixing etc.complete all as specified.

S&F for powder coated aluminium frame work for doors, windows, ventilators and partitions with one or more rebates including joining cleat for fixing etc.complete all as specified (minimum thickness of powder coating 50 micron).

S&F anodised aluminium door shutters, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleat, glazing with clips, rubber neoprene packing, anodised aluminium snap beading, 02 Nos handle in each door, hinges, screws etc including necessary locking arrangement complete all as specified. Note : Glazing/wire mesh/panels shall be measured and paid separately.

S&F anodised aluminium window and ventilator shutters, fixed/ sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21, 100mm long (2 No.) suitable handle (1 No.) complete all as specified (minimum thickness of powder coating 50 micron).

Supply only chain link MS galvanised fencing, any mesh, size or type all as specified

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed

S&F powder coated aluminium DECO grill 10mm thick,DG 104 fixed with necessery U/F/H channel etc complete all as specified and directed (Note : Deco grill shall be fixed with windows with all fittings as directed by Engineer-in-Charge)

S&F aluminium anodised DECO grill 10mm thick,DG 104 fixed with necessery U/F/H channel etc complete all as specified and directed

S&F Anodised aluminium snap grid frame work for false ceiling, wall panelling etc, size of grid 605 x 605 mm using wall angle 25x25x2mm, main Tee 38x25x1.5mm and cross Tee 25x25x1.4mm complete all as specified and directed

S&F 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework fixed flat in ceiling as per manufacturer's instruction all as specified

M&L for Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

M&L for 75 mm thick Cement concrete type C-2, 1:3:6 (40mm graded aggregate) as in sub base of flooring complete all as specified

M&L for 40mm thick Cement concrete type B- 1, 1:2:4 (20mm graded aggregate) laid in floor as sub base complete all as specified

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M&L for Makrana white/green marble 20 to 25mm thick (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms, and the like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble complete all as specified and directed

M&L for heavy duty vitrified out door tiles 10 mm thick (square / rectangular) area of each tile n exc 0.36 sqm, in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match all as specified

M&L for joint free non skid ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm, in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match all as specified

All as per item No 31 here-in-before but cutting to required size and fixed on vertical surfaces such as skirting, dado etc complete all as specified

M&L for light shade vitrified ceramic tiles, 10 mm thick (square / rectangular), polished, area of each tile not exc 0.36 sqm, laid in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match all as specified

All as per item No 33 here-in-before but cutting to required size and fixed on vertical surfaces such as skirting, dado etc complete all as specified

M&L for rendering 15mm thick on brick work or concrete surfaces in 1:6 cement mortar finished even & smooth (without using extra cement.) all as specified and directed .

M&L for rendering 15mm thick on brick work or concrete surfaces in 1:4 cement mortar finished even & smooth (without using extra cement.) all as specified and directed .

M&L for Screed bed or bedding layer or mortar in CM (1:6), 15 mm thick for laying in floor finishes all as specified and directed .

M&L for Screed bed or bedding layer or mortar in CM (1:4), 15 mm thick for laying in floor finishes all as specified and directed .

M&L for 10 mm thick backing on brick work or concrete surfaces in 1:4 all as specified and directed .

Supply and fixing on walls/ceiling or laying in floors of CPVC pipe SDR 13.5 and plain CPVC SDR 11 fittings of size 20 mm outer dia all as specified

Supply and fixing on walls/ceiling or laying in floors of CPVC pipe SDR 13.5 and plain CPVC SDR 11 fittings of size 16mm outer dia all as specified

M&L for 4 mm thick sheet glass, ordinary quality fixed with glazing clips/aluminium cleats in square not exc 0.50 sqm in each pane all as specified

M&L for 4 mm thick sheet glass, ordinary quality fixed with glazing clips/aluminium cleats in square exc 0.50 sqm in each pane all as specified

S&F 4mm thick figured glass, pin head type and glazing with glazing clips/aluminium cleats in square not exc 0.50 sqm in each pane all as specified

S&F 4.8mm thick figured glass, pin head type and glazing with glazing clips/aluminium cleats in square exc 0.50 sqm in each pane all as specified

M & L two coats of oil bound distemper over a coat of alkali resistant primer on newly plastered wall surfaces including preparation of surfaces

M & L for preparation of new ceiling surfaces of non asbestos fibre cement building boards and application of two coats of oil bound distemper complete all as specified

M & L complete removal of existing treatment and application of two coats of oil bound distemper over a coat of primer on wall surfaces complete all as specified and directed

M&L for preparation of newly plastered surfaces of external walls and applying two coats of Apex Ultima Protek System of Asian paints or equivalent of Berger/Nerolac/Dulux over a coat of antifungal primer duly applied through company authorised applicator or under company supervision using modern tools and techniques. Manufacturer and contractor shall submit performance guarantee for a period of five years from the date of completion of work complete all as specified

M&L for preparation of new steel surfaces exceeding 10 cm width or girth and applying two coats of anti corrosive paint over a coat of metal primer at any height complete all as specified and as directed

M&L preparation of old painted wooden surface of any description over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and as directed .

S & F 9 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed in aluminium frame work complete all as specified

S&F CP angle cock screwed down high pressure or butterfly handle screwed down, screwed for iron pipe of brass ferrule and fixed 15 mm bore all as specified

S&F in repairs vitreous china wash down water closet (EWC), any colour, pedestal pattern complete all as specified

S&F in repair PVC Low Level Flushing Cistern 10 Litre capacity, White, valveless, symphonic action type, with Inlet, Ball Valve, Float and Handle, fixing brackets and connections to pipes complete all as specified and as directed.

S&F PVC Conncetion 15mm size with PTMT Nuts of length 450mm and fixed, complete all as specified and as directed.

S&F Vitreous China Urinal of size 465x355x265 mm (minimum), White, Bowl type, Flat back including providing and Fixing Plugs, bedding Urinal against Wall in Cement Mortar 1:2, securing Urinal to Plugs with and including 60mm long Brass Screws, pointing around Urinal back in Cement complete all as specified and as directed.

S&F in reapair plastic seat cover, any color closed pattern with flat bottom & cover and mild steel chromium plated or aluminium hinges, etc including fixing bolts complete

S&F brass chromium plated bottle trap for wash basins with inlet or outlet screwed for pipe for connection including necessary packing, union and cap (32 mm bore) complete all as specified

S&F CP health faucet including flexible tube of size 15mm and wall hook complete of make : Parryware, Cat No. T9941A1 or equivalent in other makes as specified

S & F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls 75mm bore all as specified

S & F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls 110mm bore all as specified

S & F PVC (SWR) bends, any radius, 110mm bore all as specified

S & F PVC (SWR) bends, any radius, 75mm bore all as specified

PVC (SWR) junction single, (Single 'T') equal or unequal 75mm with access door all as specified

PVC (SWR) junction single, (Single 'T') equal or unequal 110mm with access door all as specified

S&F PVC (SWR) 110 mm dia vent cowl

S&F PVC (SWR) branch piece, single (single Y) equal or unequal with access doors, 75mm bore complete all as specified

S&F PVC (SWR) branch piece, single (single Y) equal or unequal with access doors, 110mm bore complete all as specified

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

M&L point wiring with 1.5 Sqmm PVC insulated unsheathed FRLS multistranded single core copper conductor cable in PVC concealed conduit rigid non metallic except beam, colum and RCC roof and chases cutting incl white cover plate with frame ,metal flush boxes suitable for modular switches incl 1.5 Sqmm PVC insulated copper conductor earth continuity wire for one light/fan/bell point controlled by one switch

S&F Modular switch 1 way 6A, 1 module complete all as specified

S&F Fan step regulator, 120W - 2 module complete all as specified

S&F ceiling rose surface bakelite 65 x 50mm 3 terminals complete all as specified

Taking down Ceiling fan/exhaust fan, painting,of ceiling fans complete with sinthetic enamel paint by spraying including filling cavities with filler one coat after cleaning all dust etc ang hanging in original position and connecting up including provision of cable from ceiling rose or connection to fan all as specified and directed

S&F LED recessed mounted light of 16 watt ,minimam lumen output of 100 lumen/watt,including all connection all as specified and as directed.Cat part no LD74-151-XXX-65-X of Wipro or equivalent in other makes as specified

S&F LED recessed mounted light of 33 watt ,minimam lumen output of 100 lumen/watt,including all connection all as specified and as directed.Cat part no LM17-401-XXX-57-XX of Wipro or equivalent in other makes as specified

M&L for taking down existing ceiling fan from existing position and refixing by suitable length fan rod including all connection all as specified and as directed.

M&L for taking down old unserviceable tube light from existing position including all connection all as specified and as directed,

T L ALOSIOUS

Albert Rebello and Company

Aarjay Tech Engineering

M/s Antony Kallarakkal

M.J.JOY AND COMPANY

M/s ANTONY THOMAS AND CO

Liju Engineering Works

SREENARAYANA ENTERPRISES

ANIE JOHN CONTRACTORS

M/S Babil Industries