SPECIAL REPAIRS TO SERVANT QUARTERS OF HOUSE NO 13 KB,121 KB, 333 KB,501 KB AND 532 KB AND PROVISION OF BASKET BALL COURT AT KV NO 2 AT NAVAL BASE, KOCHI

Amount

Taking down cement plastered on Brick/Concrete wall and ceiling including racking out joints, hacking for key, scrubbing down with water complete all as specified and as directed .

M& L for rendering 8 mm thick CM 1:4 with approved water proofing compound over backing coat of 12 mm thick in CM 1:6 using liquid WPC fair surfaces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid seperately.

M & L for 5 mm thick rendering in cement mortar 1:3 on fair faces of of ceiling surfaces finished even and smooth complete all as specified and as directed .

M&L for rendering 10mm thick on brick or concret wall surfaces with cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and as directed .

Demolition of Brick/block or stone masonry in cement mortar or lime mortar complete all as specified and directed . Note:- The rate quoted rate shall be deemed to be inclusive of disposal of material to outside MD land as directed by Engineer in Charge

M& L for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar 1:6, Type C1, 1:3:6 (using 20mm graded stone aggregate), complete all as specified and as directed.

Demolition of reinforced cement concrete any description any position not otherwise specifically provided for complete all as specified and as directed. Note:- The rate quoted rate shall be deemed to be inclusive of disposal of material to outside MD land as directed by Engineer in Charge

M&L for RCC Type B1, 1:2:4 using 20mm graded aggregate for foundations incl rafts,footings, foundation beams, plinth beams, bases for columns etc basement slabs complete all as specified and as directed .

M&L for RCC Type B1, 1:2:4 using 20mm graded aggregate for Columns, piers, pillars and struts all as specified

M&L for RCC Type B1, 1:2:4 using 20mm graded aggregate for beams, cantlivers, lintels etc all as specified

M&L for RCC Type B1, 1:2:4 using 20mm graded aggregate for roof slab all as specified.

Use and waste of form work to flat rough finished surfaces sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter all as specified

Use and waste of Formwork flat rough finished surfaces to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. all as specified

Use and waste of Formwork square, rectangular, or polygonal rough finished surfaces to sides of pillars, posts, struts, piers, columns and stanchions all as specified

Use and waste formwork flat rough finished surfaces to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick for rough finished surfaces of concrete (Horizontal or sloping) complete all as specified and as directed .

M&L for TMT bars in reinforcement 10mm dia and over including cut to length , bend to required shape , cranking/hooking ends if necessary and binding with 0.9mm dia MS wire annealed or welding so as to secure the bar firmly in position/required shape complete all as specified and as directed.

M&L for TMT bars 5mm dia and over and including 10mm dia in stirrups, spacers and binders etc , cut to length, bent to shape required, including cranking bending spirally for hooping for coloumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for TMT bars in reinforcement 6 to 8mm dia and over including cut to length , bend to required shape , cranking/hooking ends if necessary and binding with 0.9mm dia MS wire annealed or welding so as to secure the bar firmly in position/required shape complete all as specified and as directed .

M&L for Liquid water proofing compound complete all as specified and as directed .

M&L for preparation of new decorated surfaces of ceiling and applying three coat of white wash complete all as specified and as directed .

M&L for preparation of new decorated surfaces of new wall surface and applying three coat of white wash complete all as specified and as directed .

M&L for preparation of old decorated surfaces of walls including cornices (plastered or unplastered) and applying two coat of white wash complete all as specified and as directed .

M&L for writing letters of figures (BLOCK, ROMAN, ITALIAN OR INDIAN) n exc 30cm high all as specified and directed by Engr in Charge. Note : Writing shall be done with thick paint so that they stand out boldly.

M&L preperation of new decorated surfaces of walls (plastered or unplastered) including cornices and applying two coat of cement base paint over a coat of priming with alkaliresistant priming paint complete all as specified and as directed .

M/L preperation of old decorated surfaces of walls (plastered or unplastered) including cornices and applying one coat of cement base paint complete all as specified and as directed .

Taking down chowkats with shutters (without taking off shutters from the frame) exceeding 1.5 Sqm but not exceeding 4 Sqm complete all as specified and as directed ..

Taking down chowkats with shutters (without taking off shutters from the frame) not exceeding 1.5 Sqm complete all as specified and as directed .

Cutting holes in brick wall built in cement mortar, depth of embedded exceeding half brick and not exceeding one brick and making goof dismantled portion in cement concrete 1:2:4 type B1 for inserting hold fast complete all as specified and as directed .

Supply and fix mild steel hold fast, clamps plain angle cleats and similar small articles confirming Fe-400 complete all as specified and as directed .

Supply and fix 2nd class hard wood plain, solid, straight chowkat and frames, wrought framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed .

S&F 2nd class hard wood 30mm thick glazed,gauged and skelton window/ventilator shutters open rebated and prepared to receive glass gauze etc(without sash bars) edges of framing plain,chamfered or rounded fitted with cut and mitred beads for securing glass,gauze etc size of members of shutters as specified in SSR part I section 8 clause 8.24(b).

Supply and fix 2nd class hard wood 35mm thick glaze/gauged skeleton door shutters open rebated and panelled to receive glaze/gauge (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mittered beads for securing glass etc sizes of members of shutters and specified in SSR part 1 section clause 8.24(a) complete all as specified and directed..

Supply and Fix 2nd class hard wood 35mm thick factory made Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete complete all as specified and as directed .

Supply and fix aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified and as directed .

All as per item No 34 here-in-before but fixed in repair complete all as specified and as directed ..

Hacking out old broken glass (any thickness size, quality or description) from wooden frames glazed with putty or fitted with beads not exceeding 1.50 Sqm complete all as specified and as directed .

S&F Sheet glass ordinary quality 4.00 mm thick and glazing with oil putty / beads in squares not exceeding 0.5 Sqm in each pane complete all as specified and as directed .

Supply and fix 4.00mm thick frosted glass pin head type and glazing with oil putty / beads in squares not exceeding 0.5 Sqm in each pane complete all as specified and as directed .

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with .S. Square tube, suppling & fixing in opening complete all as specified and as directed .

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

Supply and fix aluminium anodised barrel tower bolt extruded section of 150 mm long complete all as specified and as directed .

Supply and fix aluminium anodised barrel tower bolt extruded section of 125 mm long complete all as specified and as directed ..

Supply and fix 300mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed .

Supply and fix butt hinges 100mm size stainless steel complete all as specified and as directed .

Supply and fix butt hinges 75 mm size stainless steel complete all as specified and as directed .

Supply and fix extruded aluminium alloy handles fabricated type anodised 150 mm size complete all as specified and as directed .

All as per item No 46 here-in-before but 100mm size complete all as specified and as directed .

Dismantling of floor hearth or wall tilling tiles including CM bedding (but not backing) and disposing the rubbish off the premises out of MD land complete all as specified and as directed .

Material and labour for non skid coloured ceramic tiles 7 to 8 mm thick square/rectangular area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles including provision of CM screed 15 mm thick in CM (1:6) complete all as specified and as directed .

M&L in Glazed ceramic tiles in vertical surfaces Glazed ceramic tiles in vertical surface 300x200x 7 mm thick as dado's/skirting including provision of backing coat 10 mm thick in CM (1:4) complete all as specified and as directed ..

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and as directed . Note:- Rate quoted shall be deemed to be inclusive of disposal of rubbish out of MD land premises

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite over 10mm thick screed bed in cement mortar 1:3 complete all as specified and as directed.

Rounding to edges of stone slabs one edge, of any situations complete all as specified and as directed .

Demolition of cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed. Note:- Rate quoted shall be deemed to be inclusive of disposal of rubbish out of MD land premises

Dismantling of MP tiles or similar tiles in roof covering complete all as specified and as directed .

Dismantling timber scantlings 40 Sq cm over in section for unframed work in fillets, rails, posts, rafters, purlins etc, in unframed works complete all as specified and as directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based corrugated tile profile steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GIbased Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as inroof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed .

S&F Roof trusses (framed) confirming to Fe 410W, trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and as directed .

M&L for Preparation of new steel surfaces and applying two coats of anti corrosive paint over a coat of appropriate primer complete all as specified and as directed .

M&L for rendeing 10 mm thick on concrete/ brick surfaces as in roof in CM 1:3 including WPC as per manufacturer's instrs finished even and smooth complete all as specified and as directed . Note: WPC shall be measured and paid seperately

Supply and fix in repair anodised aluminium alloy curtain rod 25 mm dia with fixing brackets, stops, rollers etc complete all as specified and as directed . Note:- One pair of end brackets of same colour as that of curtain rod shall be provided .

S & F in repair vitreous china squatting pan “ORISSA PATERN” of size 580 mm x 440 mm, white, with integral foot rest (excluding flushing cistern and flush pipe) including single trap spun casted 60 cm long fix in asian eposy mortar connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete all as specified and as directed .

Supply only PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including MS brackets 10 Ltrs capacity including flush pipe PVC connections etc complete all as specified and as directed .

Supply and fix in repairs vitreous China wash hand basin of size 580 x 450 mm white, flat back with and including waste fittings brass chromium plated 32 mm with long and fly nut screwed shank excluding taps, waste chain and plug and porcelain stopper but including cast iron brackets complete all as specified and as directed .

Supply only pillar taps, brass, with capston heads, fancy type chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, E85bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed .

S&F in repair 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed .

All as per item No.69 above but for 75 mm bore complete all as specified and as directed .

M&L 110 mm bore PVC (SWR) bends any radius complete all as specified and as directed .

All as per item No. 71 above but for 75 mm bore complete all as specified and as directed .

M&L 75 mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed .

Supply and fix tubular towel rail 20mm dia brass chromium plated with brackets fixed in repairs 60cm long complete all as specified and as directed .

Supply and fix in repairs SS gratings circular centre part Square body fixed with white cement alround, 100 mm dia with minimum weight 25 gms complete all as specified and as directed .

Supply and fix in repair door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in repair in floor, 140mm over length of cover plats complete all as specified and as directed .

S&F in repair stainless steel sink with drainage board made out of 1mm thick sheet kitchen or laboratory with plugs, washers including beding lime cement mortar to dwarf wall or including fixing cantilever brackets fixed to wall and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm including waste coupling 40 mm and waste pipe complete all as specified and directed.

M&L for 75mm thick cement concrete type D2, 1:4:8 (40 mm graded aggregate) as in sub base complete all as specified and as directed .

M & L for chequred cement concrete tile 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry as in floor with grey cement and filling joints with colour pigment over and including 20 mm thick screed bed in cement mortar 1:6 including dismantling of old tiles complete all as specified and as directed .

M&L for 75mm thick cement concrete type C1 (1:3:6) using 20 mm graded stone aggregate as in plinth Protection complete all as specified and as directed .

M&L for ATT Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed .

M&L for anti termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed .

M&L for ATT At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed .

INTERNAL ELECTRIC SUPPLY Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and as directed .

Material and labour for point wiring for one light/fan point with 1.5 sqmm PVC insulated (FRLSH) unsheathed copper conductor multistranded 1100 volts grade controlled by one way switch including 1.5 sqmm PVC (FRLSH) insulated unsheathed copper cable multistrand conductor 1100 volts grade for continuity conductor including connected to common earth dolly drawn through and including rigid PVC conduit medium grade ISI marked concealed of suitable size with all accessories and sunken box of 1.0 mm thick and 60 mm depth pressed steel box factory made for mounting of switch, socket and fan regulator with Hylem sheet including chase cutting and making good to the disturbed surface and matching to the existing finishes specifications complete all as specified and as directed .

All as per item No. 85 here in before but for one bell point controlled by one 5 Amp bell push on independent board complete all as specified and directed.

All as per item No. 85 here in before but for one 5 pin 5 Amp socket outlet point on independent board complete all as specified and directed.

All as per item No.85 here in before but for one 5 pin 5 Amp socket outlet point on same board complete all as specified and directed.

Supply and fix ceiling rose surface bakelite 65 x 50 mm 3 terminals 240 volt 50 Hz complete all as specified and directed.

S & F bell push flush type 5 Amps single pole complete all as specified and as directed by engr in charge .

S & F electric bell, AC 230 Volt single pole complete all as specified and as directed .

S & F switch piano flush type single pole one way 5 Amp one way complete all as specified and as directed.b

S & F , socket outlet 5 Amps, 5 pin, 2 in 1 complete all as specified and directed .

Supply and fixing in LED lights fitting 1x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceilingrose complete.all as specified and directed .

Supply and fixing in LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed .

S&F in Sheet metal enclosure for MCB DB, SPN, 8 ways, double door, with 200 amps rated bus bar, having IP-43 protection including taking down old DB complete all as specified and directed .

S&F in Sheet metal enclosure for MCB DB, SPN, 4 ways, double door, with 200 amps rated bus bar, having IP-43 protection including taking down old DB complete all as specified and directed .

Supply and fixing 20 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of two poles and current carrying capacity in the MCB SPN 20 amp complete with connection testing and commissioning complete all as specified and directed .

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed .

Supply and fixing LED flood light 100W 230V AC outdoor type with thermal management in multiple optics and equipped with IP 66 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and as directed.

M&L for submain wiring with 2 single core 1.5 Sqmm PVC insulated unsheathed multistranded copper conductor cable 1100V grade drawn through and including PVC rigid conduit concealed wiring including necessary PVC conduit specials including chases cutting complete except beam and RCC roof and one run of 1.5Sqmm PVC insulated unsheathed single core 1100V grade multistranded copper conductor cable as earth continuity conductor and connecting with suitable size thimble complete all as specified and directed . Note:- Two run of 1.5Sqmm size PVC cable,one run of 1.5Sqmm size PVC cable as earth wire and one run of PVC conduit shall be measured as one unit length( For Bell point)

Supply and fix MS ERW pipe 50mm dia for the support of flood lights to bend to shape as require complete all as specified and as directed .

Supplying and laying reinforced precast concrete cable cover class LV type I flat size 250mmX150mmX40mm complete all as specified and as directed.

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate cement concrete in foundations filling and mass concrete complete all as specified and as directed.

M&L for PCC 1:2:4 type B2 using 40mm graded stone aggregate cement concrete as in coping complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 using 40mm graded aggregate cement concrete in foundations,filling and mass concrete complete all as specified and as directed.

S&F framed brackets of angles or tees with web and flanges cut to shape drilled and countersunk for screw including bending and welding angles as necessary gusset plates,riveting etc n exc 10 Kg each brackets conforming to Fe 290-E 165( Brackets over 10Kg each to be measured under structural steel) complete all as specified and as directed.

S&F of polycarbonate weather proof box of size 150mmX75mmX40mm including MCB SP 20A complete all as specified and as directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) all as directed and specified .

S & F in repair fan regulator electronic step type 100 W, 250 Volts complete all as specified and as directed.

Supply & Laying LT cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6 Sqmm 3 core complete all as specified and as directed .

Excavation in trenches not exceeding 1.5 mtrs wide and not exceeding 1.5 mtrs in depth for laying of cables /shafts/well/manholes/pier holes including getting out in soft/loose soil complete all as specified and directed.

Returning filling in including spreading, leveling ,and well ramming, in layers not exceeding 25 cm each layer of soil complete all as specified and as directed .

Removing surplus excavated material from site not exceeding 50 mtrs from starting point and depositing where directed at level not exceeding 1.5 mtr above the starting point complete all as specified and as directed .

Riddle sand cushioning for cables 15cm above the cable and 18cm below the cable complete all as specified and as directed . (Note:- punned thickness shall be measured and paid )

Material and labour for well burnt brick laid flat, for cable protection complete all as specified and directed.

M & L for GI tubing light grade 40 mm bore complete with all fittings like bends, sockets, elbows and fixing clamp of suitable size for passing through cables under the floor, along the wall or along the pole complete all as specified and directed.

INTERNAL WATER SUPPLY Supply and fix on wall/concealed on wall high pressure CPVC pipes SDR-13.5 & plain CPVC SDR 11 fittings including all necessay fittings, solvents of size 25 mm dia. complete all as specified and directed.

All as per item No 118 here -in-before but of size 20 mm dia complete all as specified and directed.

Taking up or down steel tubing and connections,including cleaning for refixing or removal to store for schedule of credit 25 mm dia any type complete all as specified and directed.

Taking up or down steel tubing and connections,including cleaning for refixing or removal to store for schedule of credit 20 mm dia any type complete all as specified and directed.

Supply and fixing in repair of Bip cock, CP quarter turn with flange , long nose with wall flange cast copper alloy with crutch or butterfly handle screwed for GI/ CPVC pipe of size 15 mm complete all as specified and as directed ..Make No - Cera or Prayag/Hindware/Jaguar)

Supply and fix concealed stop cock regular body,Quarter turn with adjustable wall flange chromium plated with CP cup fancy type of size 20mm and taking down old unserviceble one, complete all as specified and as directed. Make: Cera/hindware/Jaguar

Supply and fixing of swivel overhead shower (minimum weight 40 grams) of PTMT any colour with shower arm (minimum weight 40 grams) 15 mm size, 195 mm long with bend of 45 degree ,dia 70 mm with flange for fixing with CPVC pipe and taking down old one,complete and all as specified and as directed .Make : Cera/hindware/Jaguar

M/L for cutting chasses on walls floor etc not exceeding 10 cm girth and making good the disturbed surface to match with the existing after removing the existing concealed pipe/laying new pipe, complete all as specified and directed .

Material and labour for cement concrete in foundations, filling and mass concrete type 1:3:6(40mm graded aggregate) complete all as specified and directed.

M & L for CPVC Ball Valve of size 25 mm dia suitable for CPVC pipe incl necessary fittings and taking down old unserviceble vall valve complete all specified and directed. Make: Supreme/Eurotech /Astral/SFMC

All as per item No. 127 above but of size 20 mm dia complete all as specified and directed..

Supply and fixing in replacement of Rotational mouldede polyethylene water storage tanks (cylinderical vertical with closed top) hoisted & fixed in position of capacity 500 ltrs incl taking out u/s old one. Make : Sintex (ISI)/ Aquatech

S/F float valve synthetic(PVC) of size 25 mm dia high pressure with polythene ball of size 6" dia and flynut including taking down old one complete all as specified and directed.

Provision of Basket Ball court with following specifications:- a.Excavating over areas, n exc 1.5 m deep and getting out soft/loose soil b.M&L for treating the bottom and sides of excavation entire area at the rate of 5 litres of emulsion per square metre of surface area. c.M&L for 150 mm thick soling(or subbase)with broken boulders or quaried stone size range 100 mm to 50 mm, interstices filled, surface formed and rolled and consolidated to required gradient and camber complete. d.M&L for WBM 150 mm thick (compacted thickness) in two layer(75mm thick in each layer) with course aggregates grading 2(63 to 40 mm size) spread , rolled and consolidated to gradient and camber required with powered steel wheel tandem rollercomplete. Note: Removal of excavated soil at a distance of exc 1.5km but not exc 5 Km from starting point and where directed by Eng: in charge 2.Asphalting Leveling a.M&L for Preparing surfaces by brushing with wire brushes for removing caked mud etc. Sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. complete all as specified and as directed. b. M&L for appying evently a priming / tack coat with bituminous primer with cold emulsion @ 10 Kg/10 Sqm using paving bitumen over bituminous macadam all as specified and as directed. c.M&L for pre-mixed bituminous macadum laid/rolled with power roller 8 to 12 Ton roller complete to required gradient and camber (consolidated thickness 75 mm) and binder content 4% by wight of total mix complete all as specified and directed. d.M&L for appying evently a priming / tack coat with bituminous primer with cold emulsion @ 5 Kg/10 Sqm using paving bitumen all as specified and as directed. e.M&L for Bituminous premix asphaltic dense concrete 40mm consolidated thickness with 5.50% binder content by weight of total mix, (with 7% bitumen replaced by sheedded waste plastic as per RC SP 98-2013) rolled and compacted to required camber and gradient complete all as specified and as directed. f. M&L for Premixed sand seal coat with 0.06 cu.m. of sand mixed with 6.8 kg of bitumen, applied and rolled to a uniform smooth surface.

Removing excavated material exc 1.5Km n.exc 5Km and depositing where directed at a level n.exc 1.5m above starting point complete all as specifed and as directed.

M&L PCC 1:3:6 type 'C-1' (using 20mm graded stone aggregate) in foundation filling and mass concrete complete all as specified and as directed.

Material and labour for rendering 15 mm thick on fair faces of brick work in CM 1:4 finished even and smooth without using extra cement.

M&L for PCC type B-1, 1:2:4 (20 mm graded aggregate) as in coping complete all as specified and as directed.

M&L for Cement concrete 1:2:4 Type B1 (using 20 mm graded stone aggregate )in surface channels and drains

5 Layers Acrylic system: SUPPLY AND APPLY OF ALL WEATHER PROOF ACRYLIC SYNRTHETIC FIVE LAYERS FLOORING SYSTEM FOR BASKET BALL COURT. (BRAND-UNICA MADE IN EUROPE OR EQUIVALENT AND APPROVED BY INTERNATIONAL TENNIS FEDERATION) : 1.Filler Course:- Providing and laying one layer of acrylic resurface blended with silica sand. 2.Cushion Course :- Providing and laying two layer of smooh cushioned finish in preparation for the texture and finish courses. 3.Texture Color Course:- Providing and laying one coat of color provides a uniform surface texture. 4.Finish Color Course :- Providing and laying one coat of color will create durable finish highly resistant to weather and ultraviolet degradation. 5.Game Line Marking :- Providing and laying of game line marking per standard.

Basket ball Pole M&L for providing Basket ball poles 02 Nos with following specification:- (i) Excavation in post holes of size 1.00X1.00X1.00 m and removal of surplus soil (ii) PCC 1:3:6 type C1 using 20mm graded stone aggregate as in foundation filling (iii) 200mm nominal bore of MS pipe of medium weight and 10mm thick base plate of size 0.6X0.6 m and 100mm dia stay pipe for extra support to the post at swan neck portion of the pipe. (iv) 180cmX105cm transparent acrylic board 20mm thick and fixing arrangement to MS pipe including dunking ring and nylon net complete all as specified and as directed. (v) PU spray paint on MS posts complete all a specified and as directed.

JKM CONSTRUCTIONS

K THOMAS AND COMPANY