CA NO GE(N)AMB-81/2025-26 SPECIAL REPAIR OF BLDG. NO. P-388 (OR TOILET), 192 (OR TOILET) 1,177 (JCO LIVING), 354 (OFFICE COMPLEX) OF EME BN UNDER AGE B/R-I OF GE (NORTH) AMBALA CANTT

Schedule 'A' Part-I (B/R itmes) Dismantling asbestos cement (corrugated, semi corrugated, etc.) plain sheets in roof coverings including ridges ,complete all as specified and as directed.

Supply and Fixing pre–painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick, having zinc coating 150 gm per sqm (Az–150) of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws ,complete all as specified and as directed.

Supply and Fixing pre–painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, having zinc coating 150 gm per sqm (Az–150) as in roof covering/ cladding to wall, fixed with self tapping screws ,complete all as specified and as directed.

Dismantling of boarding of any description and in any position (ceiling/wall panelling) of any size ,complete all as specified and as directed.

Supply and fixing of GI Metal Suspended ceiling of approved materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm centre to centre and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm centre to centre along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, and as directed by Engineer-in-charge. GI Metal Ceiling laying perforated Tengular edge global white colour tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fibre acoustical fleece. Note- Ceiling tiles and ceiling grid shall be of the same make.

Taking down roof trusses, coupled rafters or trussed beams etc., for renewal of any defective members (timber renewed to be measured separately) and reassembling of clear span above 4 metres & upto 8 metres,complete all as specified and directed.

Dismantling of timber scantlings 40 sq cm and over in section, in any position, unframed work complete all as specified and directed.

Supply and Fixing mild steel work as in tubular trusses including special shaped washer etc, complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St-240, complete all as specified and as directed.

Material and labour for preparation of new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer ,complete all as specified and as directed.

Dismantling of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar, etc. but excluding ashlar facing, dressed stone work and precast concrete articles ,complete all as specified and as directed.

Material and labour for brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 ,complete all as specified and as directed.

All as per serial item No. 11 here in befor but except bricks (old serviceable bricks obtained from serial item No 10 above including removing motar, cleaning the bricks with water,shall be used ) ,complete all as specified and as directed.

Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including racking out joints, hacking for key scrubbing down with water, etc. ,complete all as specified and as directed.

Material and labour for rendering 15mm thick on any faces of brick work or concrete wall surfaces in cement mortar (1:6) and finished even and smooth without using extra cement, complete, all as specified and as directed.

Material and labour for rough cast plaster complete as specified in SSR Part-I, clause 14.22 shall consisting of following:- firstly apply under coat in cement mortar 1:4 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine stone aggregate of size between 6 to 12 mm as per the texture required mixed with coarse sand and cement in the ratio 1:1:1 shall be applied, ,complete all as specified and as directed.

Supply only integral water proofing compound,complete all as specified and as directed.

Material and labour for rendering 05 mm thick on fair faces of brick work or concrete ceiling surfaces, chajjas, etc. in cement mortar 1:3 and finished even and smooth without using extra cement ,complete all as specified and as directed.

Material and labour for preparation of new plastered/unplastered surfaces of walls, chajjas, roof projection, etc. and applying two coats of cement base paint over and including 1 to 2 mm thick wall care putty white cement based in one or two coats to achieve smooth surfaces ,complete all as specified and as directed.

Material and labour for preparation of newly plastered/ unplastered surfaces of walls and applying two coats of acrylic distemper with painting roller over and including 1 to 2 mm thick wall care putty white cement based in one or two coats to achieve smooth surfaces, ,complete all as specified and as directed.

Material and labour for preparation of new plastered/unplastered surfaces and applying three coats of white lime wash on surfaces of ceiling, chajjas, roof projection etc., ,complete all as specified and as directed.

Material and labour complete removal of existing treatment on walls, pillars, cornices etc (any number of layers) by scrapping with steel scrappers or any other means, wasing down with water to remove loose particles etc and applying two coats of cement base paint over a coat of alkali resistant primer , complete, all as specified and as directed.

Material and labour complete removal of existing treatment on walls, pillars, cornices etc (any number of layers) by scrapping with steel scrappers or any other means, washing down with water to remove loose particles etc and applying two coats of oil bound distemper/acrylic distemper over a coat of alkali resistant primer , complete, all as specified and as directed.

Material and labour complete removal of existing treatment on ceiling (any number of layers) by scrapping with steel scrappers or any other means, wasing down with water to remove loose particles etc and applying two coats of white lime wash,complete all as specified and as directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises ,complete all as specified and as directed.

Material and labour for Non Skid coloured ceramic tiles joint free premium/1st quality 7 to 8 mm thick, (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 ,complete all as specified and as directed.

Material and labour for glazed ceramic coloured tiles joint free premium/1st quality in vertical surfaces/skirtings/dados of size 300x 600x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on faces of brick / concrete surfaces in cement mortar (1:4) ,complete all as specified and as directed.

Material and labour for vitrified ceramic tiles light shade,1st quality,(square/ rectangular), 10mm thick, area of each tile exceeding 0.36 sqm and not exc 1.00 sqm as in floor, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes ,complete all as specified and as directed.

Material and labour for vitrified ceramic double charged light shade tiles, 1st quality, of same description as of floor tiles in serial item No. 27 above but 100mm to 200mm height as in skirting, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including rendering 10 mm thick in cement mortar 1:4 ,complete all as specified and as directed.

Demolition of cement concrete (un–reinforced) in ground floors and pavings not exe 15 cm thickness (below or above ground level) ,complete all as specified and as directed.

Material and labour for 25 mm thick PCC 1:2:4, type B0 as in sub base of floor (using 12.50mm graded crushed stone aggregate), finished even & fair without using extra cement ,complete all as specified and as directed. Note- This item shall not be executed in the location, where dismantling of tiles only have been done.

Material and labour providing 50 mm thick cement concrete 1:3:6 type C–1 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (not exc 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight including form work complete, all as specified and as directed.

Taking down chowkats or frames with shutter area exceeding 1.50 Square meter and not exceeding 4.00 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish ,complete all as specified and as directed.

Taking down chowkats or frames with shutter area not exceeding 1.50 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish ,complete all as specified and as directed.

Supply and Fixing for mild steel of angle /tee /beam /hollow MS section for door /window frames /chowkhat, window guard bars, hold fasts etc., and similar articles conforming to Fe–410–0 or Fe–310–0 complete all as specified and directed.

Material and labour for factory made 35 mm thick 2nd class hard wood glazed and skeleton shutters,open rebated and prepared to receive glass , gauze etc. (without sash bars) ,edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I, Section-8, clause 8.24 (a) (wood shall be kiln seasoned and chemically pressure treated) ,complete all as specified and as directed.

Material and labour for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer ,complete all as specified and as directed.

Supply and Fixing for powder coated (50mic min thickness) aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete shall as specified.

Supply and fixing powder coated aluminium section (minimum thickness of powder coating 50 micron) for frame and shutters of doors, windows (fixed, sliding, hangung) & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws , complete, all as specified and as directed. Note : (a). Glazing shall be measured and paid separately. (b). Weight of aluminium sections shall be as per IS or actual weight which ever less shall be measured. (c). The rates quoted shall be inclusive of neoprene beading, glazing clips, jointing clips, screws, etc as required and the same shall not be measured for arriving the weight. (d). The rates shall be inclusive of locking arrangement including complete packing with silicon gel alround contacting surface of aluminium framework and including matching the existing surface area complete all as specified and directed.

Supply and fixing of solid PVC door frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet on single side used instead of plain colour PVC sheet reinforced with MS square tube, edges will be painted to match with prelaminated sheet and fixed in opening ,complete all as specified and as directed.

Supply and fixing of factory made solid PVC moulded door shutters with particle board core 28 to 30 mm thick (styles) with 2, 4, or 6 raised panel design with 2 mm thick prelaminated moulded PVC sheet on the front face and 2mm thick plain colour PVC sheet on back face fixing in frame at site as per specification and drawing ,complete all as specified and as directed.

Supply and Fixing double shutter steel window box type ERW hollow P section comprising of glazed/gauged skeleton shutter fabricated from following sections :- (a) ERW hollow P section frame of size 60 mm x25 mm made from 1.25 mm thick MS sheet (02 Nos i.e. 01 for glazed shutter and 01 for gauzed shutter ). Both P section shall be welded with flat iron 25x03 mm thick all around of frame on both inner and outer faces . (b) Style and rails of window shutters shall be fabricated with ERW hollow P section of size 50 mm x25 mm made from 1.00 mm thick MS sheet and comprising of 02 Nos sash bars for glazed window leaf of T – section 20 x 03 mm thick and one No sash bar of 20 mm x 3 mm thick section for gauzed winodw leaf . (c) Vertical mullion shall be ERW hollow T -section of size 60 x 25 mm made from 1.25 mm thick MS sheet (d) The above steel window shall be deemed to include the following accessories/ fittings : i) Hold fast 150mm long mild steel flat iron 12x3 mm thick made to shape- 04 Nos per window ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt stove enamelled 150mm long- 2 Nos per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 No per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 No per leaf vi) Pintal hinges 12 x 75 mm - 2 Nos each leaf vii) 10mm square Guard bar @ 10 cm c/c welded to frame . (viii) Two coat of Synthetic enamel paint over one coat of red oxide primer. (ix) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in gauzed skelton shutter of window with flat iron 15 x 03 mm with steel screws . (x) 3mm thick sheet glass, ordinary quality and with oil putty in square n. exc 0.5 sqm in each pane fixed in glass shutter of window. (xi) Fabrication and fixing arrangements as per specification including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed. Notes : (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery, grill and other accessoriries as mentioned above. (iii) The window upto 1.00 metre width shall consists of two leaves both for gauzed shutter and glazed shutter and all the shutters are openable. The window more than 1.00 metre width shall have two openable leaves on both outer side for gauzed shutter and glazed shutter and middle leaf/shutter shall be fixed type.

Supply and fixing box type using ERW hollow 'P' section ventilators fixed type with glazing bar including MS grills of square bar 10mm dia @ 100 c/c complete with glazing bars dovetailed or welded, including two coat of synthetic enamel ordinary tint paint over a coat of red oxide primer , complete, all as specified and as directed.

Supply and fixing of double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty as in repair ,complete all as specified and as directed.

Supply and fixing for 200mm long aluminium, anodised, barrel tower bolt of extruded section, complete all as specified and directed.

Supply and fixing for 200mm long aluminium handles, cast type, anodised complete, all as specified and directed.

Supply and fixing for 100mm MS Butt hinge medium weight cold rolled, complete all as specified and directed.

Supply and fixing 300 mm long aluminium sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12 mm dia with and including minimum of 6 bolts and nuts, four on bolt plate and two on staple and fixed , complete, all as specified and as directed.

Supply and Fixing in repair for mild steel mortice lock, vertical type, size 100mm including handle and fixing screws /arrangements complete in all respect as directed.

Supply and fixing 3mm thick frosted sheet glass ordinary type and glazing with aluminium beading, rubber packing or oil putty in square n exc 0.5 sqm each pane, complete all as specified and directed.

Supply and Fixing in repair for floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified.

Supply and Fixing stainless steel curtain rod 25mm dia having wall thickness 1.00mm fixed with and including stainless steel decorative brackets, two lotto for each rod length at both end etc as in repair ,complete all as specified and as directed.

Material and labour for sheet glass 3.0mm thick ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters,complete all as specified and as directed.

Supply and fixing of stainless steel wire cloths 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple ,complete all as specified and as directed.

M&L reinforced cement concrete (Nom mix) Type B–1, 1:2:4 (12.5mm graded crushed stone aggregate) aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span ,complete all as specified and as directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for flat rough finished concrete complete all as specified and directed.

Supply and Fixing mild steel TMT bar 10 mm dia and over cut to length bent to shape required including cranking bending spirally for hopping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0,.9mm dia or screwing with clip etc all as specified.

Material and labour TMT steel bars 5mm dia and over up to and including 10mm dia in stirrups, spacers etc, cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia ,complete all as specified and as directed.

Material and labour for providing PCC (1:4:8) Type D2 using 40mm graded crushed stone aggregate as in foundations, filling and mass concrete, ,complete all as specified and as directed.

Material and labour for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand with grey cement and no pigments complete, all as specified and as directed.

Material and labour for galvanised iron tubing 15mm bore, ISI marked, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, as in repair, complete all as specified and as directed.

Material and labour galvanised iron tubing 20 mm bore, ISI marked, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors as in repair ,complete all as specified and as directed.

Supply and fixing 15mm bore cast copper alloy fancy type, chromium plated stop valves with long shank and cup (concealed type), screwed down, high pressure with capstan head, screwed both ends for iron pipe or for unions as in repair, complete, all as specified and as directed.

Supply and fixing 15mm bore cast copper alloy chromium plated angular stop valves with capstan head, screwed down, high pressure screwed both ends for iron pipe or for unions as in repair , complete, all as specified and as directed.

Supply and fixing bib taps 15mm bore fancy type brass chromium plated with long body, wall flanges and capstan head, screwed down, screwed for iron pipe or for brass ferrule and fixed as in repair , complete, all as specified and as directed.

Supply and fixing fancy type pillar tap of 15mm bore, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe as in repair , complete, all as specified and as directed.

Supply and fixing as in repair brass chromium plated tubular towel rail, 20mm dia, 60cm long between flanges ,complete all as specified and as directed.

Supply and Fixing in repair 15mm bore brass chromium plated overhead shower 200mm x 200mm square shape single flow alongwith 15mm bore shower arm 600 mm long complete all as specified and directed.

Supply and fixing PVC connections 15 mm size and 450 mm of length with PTMT nuts and PVC washers on both ends as in repair ,complete all as specified and as directed.

Supply and fixing as in repair vitreous china squatting pan, Orissa pattern, 580 mm x 440 mm size, white colour with integral foot rest and PVC SWR 'P' or 'S' trap of pressure rating 6 Kg per square cm complete including provision of cement concrete bedding, connection to trap, outgoing flushing pipe, anti syphonage pipe, etc. ,complete all as specified and as directed.

Supply and fixing in replacement 10 litre PVC valveless syphonic action type flushing cistern with inlet ball valve float, handle, etc. with and including brackets, flush pipe, etc. and connections of flush pipes to WC ,complete all as specified and as directed.

S&F vitreous china wash hand basin white, flat back of size 550mm x400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of waste fitting etc as in repair , complete, all as specified and as directed.

Supply and fixing sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 mm wide with chromiun plated brackets guard and railing 60 cm long as in reapir ,complete all as specified and as directed.

Supply and fixing soap dish, brass chromium plated, approximate size 160x160x90mm, fixed to plugs with chromium plated brass screws as in repair, complete, all as specified and as directed.

Cutting chases to brick wall built in cement mortar, pinning in making good to facing where required and pointing in CM 1:3 to edges of landing , steps , cills , sunshades, shelves , lintel etc. and cutting chases for concealed water tubing etc and making good cutting not exc 10 cm girth ,complete all as specified and as directed.

Supply and fixing of 20 mm bore Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe as in repair, ,complete all as specified and as directed.

Supply and fixing , water storage tank, 500 ltr capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm dia high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore and including 20mm bore tank nipple & one 20mm GI union at outlet and including disconnecting and dismantling of existing water tanks and removing from site all as specified in SSR Part–I , ,complete all as specified and as directed. Note : - The colour of tanks shall be white colour .

Material and labour for 75mm bore PVC (SWR) multi-floor trap, plain with grating including jointing with solvent cement as in repair,complete all as specified and as directed.

Supply and Fixing glazed cermaic tiles white of size 150x75x5/6mm in repairs in neat cement slurry with required alphabet /numbe printed black on tilesfor the purpose of marking bldg no/Qtr no including hacking for key complete all as specified and directed

Taking down of 100 /75mm internal dia PVC /cast iron drain pipes /rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan–necks, etc., including cleaning or refixing or removal to store, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

Supply and fixing 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor or fixed to wall , complete, all as specified and as directed.

Supply and fixing 110mm bore PVC (SWR) bends of any radius , complete, all as specified and as directed.

Supply and Fixing in repair 110mm bore PVC (SWR) Tee and provided with access door complete all as specified

Supply and Fixing in repair 110 mm bore PVC cowls 110mm bore complete all as specified and directed

Supply and Fixing 75mm bore PVC (SWR) pipes single socketed incl all necessary fitting bend, tee, single Y etc. in any length with rubber ring joints, laid in floor /trenches ,complete all as specified and as directed.

Supply and fixing 75mm bore PVC (SWR) bends of any radius , complete, all as specified and as directed.

Dismantling Brick tiles or terracing tiles, single layer on roofs , complete, all as specified and as directed.

Demolition of mud in roofs, any thickness, including plastering and leeping (whethere full thickness removed or only a part thereof) including emoving old tar felt, all loose dirt, cement plaster, cleaning the concrete surface including removal & cleaning of vegetation, fungus, moss, small trees etc from the roof top with wire brush, removing the strips of lightening conductor including refixing the same after repair work , complete, all as specified and as directed.

Material and labour for providing cement concrete (1:2:4), Type B1, using 20mm graded crushed stone aggregate as in roof kerbs or mud stops, roof padding, etc., rounded or chamfered on edges including from work where ever required , complete, all as specified and as directed.

Material & Labour for providing and laying 3mm thick APP (atactic polypropylene polymer) modified prefabricated five layer weight not less than 3.60 kg /Sqm water proofing membrane black finish reinforced with non woven polyster matt and consisting of a coat bituminous primer @ 0.40 litre /Sqm by the same membrane manufactures of density 0.87 to 0.89 kg/ltr at 25 degree centegrate temperature and viscosity 70–160 cps over the primer coat with overlap of 100mm at the side and 150mm at the end, the layer membrane shall be laid using butane gas torch and sealing all joints etc. after preparing the surface complete as per standred practice as per manufacture's instructions. The vital physical and chemical parameters of the membrane shell be under :– (i) Joint strength in longitudinal and transverse direction at 23 degree centegrate at 650/ 450 N /5 cms (ii) Tear strength in longitudinal and transverse direction at 300/250N/5 cms. Softing point of membrane not less then 150 degree centegrate when tested in accordance with ASTM (d–5147) (iii) The laying of membrane shell be got down through the authorised applicator of manufactures of membrane only , complete, all as specified and as directed. (iv) The work shall be carriout at a height upto 12 metre.

Material and labour cement concrete tiles 30 cm x 30cm x 20 mm thick, machine pressed laid on screed bed and joints grouted and pointed flush in cement mortar (1:3) mixed with 5% crude oil by weight of cement including screed bed 15 mm thick in cement mortar (1:6) , complete, all as specified and as directed.

Schedule 'A' Part-II (E/M itmes) Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder, socket outlet, etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc., complete, all as specified and as directed.

Material and labour for point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling surfaces and including provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade, ISI marked with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes modular type of size/modules as required at site with earth dolly (boxes shall be galvanised or painted with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally) including provision of new covered plate over sunken box for housing the modular switches , modular socket outlets,modular fan regulators etc. for one light/fan/exhaust fan/bell point controlled by one way switch, complete all as specified and as directed by Engineer-in-Charge. Note :- a) All chases will be cut by chase cutter only b) Switch, socket outlet and fan regulators to be measured and paid for separately .

Description all as per serial item No.93 here-in-before but for One 3 pin, 6 Amps, socket outlet controlled by one switch on independent board, complete, all as specified and as directed.

Description all as per serial item No.93 here-in-before but for One 3 pin 6 Amps socket outlet controlled by one switch on same board, complete, all as specified and as directed.

Description all as per serial item No.93 here-in-before but for one socket outlet 16 Amp with 2.50 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 2.50 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade, ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly , complete, all as specified and as directed. Note : (i) Point wiring shall be done in a manner that not more than 02 socket point executed in one circuit. (ii) Each socket point will be measured and paid as per point.

Description all as per srl item No 93 here-in-before but for one socket outlet 16 Amp with 4.00 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 4.00 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly , complete, all as specified and as directed. Note : (i) Point wiring shall be done in a manner that not more than 01 socket point executed in one circuit. (ii) Each socket point will be measured and paid as per point.

Supply and fixing of modular switch 1 module, single pole, one way 6 Amps flush type, 230 volts, , complete, all as specified and as directed.

Supply and fixing of modular switch 1 module, single pole, one way 16 Amps flush type, 230 volts , complete, all as specified and as directed.

Supply and fixing of modular socket outlet multipin combined, 6 Amp, one way, two module, 230 volts , complete, all as specified and as directed.

Supply and fixing of modular socket outlet multipin combined, (6pin), 6/16 Amp, one way, two module, 230 volts , complete, all as specified and as directed.

Supply and fixing as in repair electronic Fan regulator, modular 100 watts, 1 module, 230 volts , 50 Hz, AC supply suitable for ceiling fan any type/make/sweep, complete, all as specified and as directed.

Supply and fixing ceiling rose surface type 2/3 terminal polycarbonate, isolated body , complete, all as specified and as directed.

Supply and fixing in repair LED batten fitting 20 watt, 4 feet, polycarbonate housing with electronic driver cool/warm type, connecting with copper conductor flexible cable from ceiling rose to connector of the light, ,complete all as specified and as directed. Cat part No. LBLN-20-C-SQ of make Orient or equivalent make given in Appx 'B'.

Supply and fixing in repair LED batten fitting 10 watt, 2 feet, polycarbonate housing with electronic driver cool/warm type, connecting with copper conductor flexible cable from ceiling rose to connector of the light, ,complete all as specified and as directed. Cat part No. LBLN-10-C-SQ of make Orient or equivalent make given in Appx 'B'.

Supply and fixing in repair, LED Bldg Security Light Fittings of capacity 40-45 watt made up of die cast aluminium housing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including electronic driver and making electrical connection, ,complete all as specified and as directed. Cat part No.LSFS-45-CF-PC of make Orient or HLSLD-14-40-CWDL-R01 of make Halonix or equivalent make given in Appx 'B'.

Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket 20 Amp complete with and including one single pole MCB.20 Amp, 10 KA 'B' curve including removing old unserviceable enclosure, ,complete all as specified and as directed. Cat part No. 811955 of make Indo Asian or equivalent in make given in Appx 'B'.

Supply and fixing sheet metal MCB DB SPN 8 way with 200 Amps rated bus bar single pole and neutral with double door IP-43 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old unserviceable enclosure , ,complete all as specified and as directed. Cat part No.811807 of make Indo Asian or equivalent in make given in Appx 'B'.

Supply and fixing MCB SP, 6-32 Amps, 240 volt,10 KA , 'B' curve as per site requirement including removing old unserviceable MCB , ,complete all as specified and as directed. Cat Part No 811008 of make Indo Asian or equivalent in make given in Appx 'B'.

Supply and fixing MCB SPN 32 Amps, 240 volt,10 KA , 'B' curve as per site requirement including removing old unserviceable MCB , ,complete all as specified and as directed. Cat Part No 811034 of make Indo Asian or equivalent in make given in Appx 'B'.

Taking down and Hanging only ceiling fan after cleaning in any model/size etc and making all connection using three core copper conductor flexible cable in size 1.5 sqmm including ceiling fan down rod of any size as per requirement drawn through PVC flexible conduit pipe from ceiling rose to fan connector complete all as specified and directed.

Supply and laying as in repair sub main wiring with two run of 6 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 6 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked multi stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium grade ISI marked of adequate size for housing the wires, ,complete all as specified and as directed. Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. (ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length.

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earth wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15mm bore(medium grade) and connected to earthing test point as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm c/c both ways with one handle for lifting made out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing as in repair, complete all as directed by Engineer-in-Charge and earth testing on completion .

Supply and Laying or fixing or passing through pipe or laid in trenches and testing cable XLPE insulated, armoured heavy duty electric cable with multistranded aluminium conductor 1100 volts grade, 2 core of size 25 Sq.mm, ,complete all as specified and as directed.

Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc. and getting out for soft/loose soil, complete all as specified and as directed by the Engineer-in-Charge

Supply and lay in repair, GI tubes light grade with connected fittings laid in trenches/wall/ pole for protection to UG cables of size 32 mm dia., ,complete all as specified and as directed.

Material and labour for cushioning for protection of cable using dry river sand, free from particles, ,complete all as specified and as directed.

Material and labour for Protection to cable with one layer of new bricks laid flat butting to each other in such a way that the length of the bricks is at right angle to the central axis of the cable using old size sub-class ‘B’ bricks, ,complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceedig 25cm for soft/loose soil, ,complete all as specified and as directed.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceedig 1.5 m above the starting point, ,complete all as specified and as directed.

Note:- Amount of credit of Rs. 58,918.50 for retrieved materials is mentioned in Schedule of Credit Page No. 123 & 124 of tender doCubic metre ents in pdf form which will be deducted offline while acceptance of tender.