ROVN OF DEFICIENT SAILORS SINGLE LIVING ACCOMMODATION APPROX 179 SAILORS AT INS VALSURA JAMNAGAR

Amount

Total amount of Sch 'A' part-I ( Building/Structure)

Total amount of Sch 'A' part-II (Excavation, earthwork & site clearance)

Total amount of Sch 'A' part-III (Internal water supply)

Total amount of Sch 'A' part-IV (Internal Electric Supply)

Total amount of Sch 'A' part- V(External Water Supply)

Total amount of Sch 'A' part-VI (External Electric Supply)

Total amount of Sch 'A' part-VII (Area Drainage )

Total amount of Sch 'A' part-VIII (Sewage Disposal)

Total amount of Sch 'A' part-IX ( Road/ Path )

Total amount of Sch 'A' part-X (Retaining wall)

Total amount of Sch 'A' part-XI (Fencing and Gate)

Total amount of Sch 'A' part-XII (Hot water supply)

Total amount of Sch 'A' part-XIII (Arboriculture)

SCH. 'A' PART -XIV (Miscellaneous B/R & E/M Items ) Note :- This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Internal Electric Supply

Point wiring using approved colour coding as per IS with multi-stranded copper conductor 1.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI marked including heavy duty PVC concealed conduit and conduit accessories concealed in wall/roof/floor etc, ISI marked including modular GI flush box of suitable size with inner and outer white plastic plate (Same make of approved switch and socket) including PVC insulated multi-stranded copper conductor 1.5 Sqmm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for One light/Ceiling Fan/exhaust fan point controlled by one 5/6 amps one way switch. (NOTE: Switch and socket shall be measured and paid for separately)

All as per item No 16 here-in-before but for One Socket outlet, three/five pin, 5 Amp, independent controlled by one 5/6 amps one way switch or switch/socket combination 5 amps, 5 pin.

All as per item No 16 here-in-before but for One light point controlled by 2 Nos, 2 Way switches 5/6 Amps

Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor 2.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI marked including heavy duty, PVC concealed conduit and conduit accessories concealed in wall/roof/floor etc, ISI marked including modular GI flush box of suitable size with inner and outer white plastic plate (Same make of approved switch and socket) , including PVC insulated multi-stranded copper conductor 2.5 Sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the one 3/5 pin 15/16 amps socket outlet independent. (NOTE: Switch and socket to be measured and paid for separately)

TV socket coaxial, I Module with GI flush box, inner and outer plate complete

Telephone socket coaxial, I Module with GI flush box, inner and outer plate complete

Angular lamp holder, PVC/ Polycarbonate type with back plate, 230V (ISI marked) surface complete with LED lamp 5 Watt all as specified

Ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) including fixing of down rod and connecting up complete with and including three core flexible PVC insulated multi stranded copper conductor cable of size 0.5 Sqmm from ceiling rose connector to fan complete all as specified

Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, copper winding of sweep 250mm, 900 RPM including connecting up from ceiling rose with 3 core flexible copper cable, PVC sheathed of size 1.5 Sqmm complete all specified

Exhaust fan, steel body AC single phase, 230V of size 300mm sweep with blades and frame and louvers including connecting up from ceiling rose with 3 core flexible copper cable, PVC sheathed of size 1.5 Sqmm complete all as specified

LED Light fitting 4 feet, 1 x 20W, 220V, AC decorative aluminium box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified

LED luminaire 600mm x 600 mm, 35/36 Watt, 220V, AC surface mounted type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper concudctor cases of suitable size complete all as specified

LED street light/ building security light fitting 35 Watt 230V, AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete with suitable GI pipe bracket bent to shape and fixed with suitable clamps on wall mounting

VTPN DB 4 way, double door IP 54 protection, with 200A rated busbar, suitable for MCCB incomer, earth termination complete all as specified

MCCB TPN 63 Amps, breaking capacity 36 KA, Frame 1, suitable for mounting on DB complete

Submain wiring with 4 runs of 6 sqmm(for phases and neutral) multistranded copper conductor PVC FRLS insulated unsheathed with and 01 run of 6 sqmm multistranded PVC insulated unsheathed copper conductor (as earth continuity conductor) connected to common earth dolly drawn through and incuding concealed PVC conduit 32mm medium grade ISI marked with accessories. Note : 05 Runs of 6 Sqmm multistranded copper conductor PVC FRLS insulated unsheathed and one run of PVC conduit 32mm medium grade shall be measured as one unit.

Submain wiring with 2 runs of 4 sqmm(for phases and neutral) multistranded copper conductor PVC FRLS insulated unsheathed with and one run of 4 sqmm multistranded PVC insulated unsheathed copper conductor (as earth continuity conductor) connected to common earth dolly drawn through and incuding concealed PVC conduit 25mm medium grade ISI marked with accessories. Note : 03 Runs of 4 Sqmm multistranded copper conductor PVC FRLS insulated unsheathed and one run of PVC conduit 25mm medium grade shall be measured as one unit.

Submain wiring with 02 runs of 4 sqmm(for phases and neutral) multistranded copper conductor PVC FRLS insulated unsheathed with and one run of 4 sqmm multistranded PVC insulated unsheathed copper conductor (as earth continuity conductor) connected to common earth dolly drawn through and incuding PVC conduit 25mm on surface medium grade ISI marked with accessories. Note : 03 Runs of 4 Sqmm multistranded copper conductor PVC FRLS insulated unsheathed and one run of PVC conduit 25mm medium grade shall be measured as one unit.

Earthling complete with galvanized GI earth plate electrode of size 600x600x6.00 mm, buried directly in ground (earth pit not less than 2.25 mtr below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to galvanized earth lead wire 4.0 mm dia by means of volts, nuts, check nut and galvanized iron or steel including earth work in any type of soil, charcoal salt 15 cm around the earth plate as shown in electrical plate No 3 of SSR part1991,20 mm dia watering pipe medium grade 1.50 mtr long GI protection pipe light grade 15 mm dia from earth pit to main board (NOTE:- maximum length of GI protection pipe with each earth shall not be less than 7.5 mtrs) including necessary pit with cover , including testing on completion

Installation, testing and commisioning Open well Horizantal Submersible pumpset ,electric driven, 415 V,Three Phase, Discharge 860-400 LPM at Head 20-30 Mtr, stainless steel shaft for no corrosion, strainer, chrome steel impeller and cutter etc of suitable capacity complete all as specified

Supply, installation, testing and commissioning outdoor type LT junction box made out of 3.15 mm thick MS sheet of size as per relevant IS duly painted of entire steel surface with two coats of first quality synthetic enamel paint over a coat of zinc chromate primer having proper locking arrangement in front, mounted on 40mm x40mm x5mm thick MS angle iron minimum height 1 mtr from ground level. Out of 1 mtr, 50 cm length of angle portion shall be embeded in PCC 1:3:6 type C1 foundation (using 20 mm graded granite stone aggregate) over sub base 100 mm thick PCC 1:4:8 D2 (using 40 mm graded granite stone aggregate) comprising the following accessories all as specified and directed complete. (a) MCB TPN 40 Amps 16 KA - 01 No for incoming (b) MCB TP 16 Amps 10 KA - 02 Nos (c) Submersible pump starter DOL Model No. BE1-SPSSDX204.316X-B suitable for open well submersible pumpset 3 HP 3 phase 415 volt,50 - 02 Nos (d) Single phase preventer, AC, 415 Volts - 02 Nos Note: (i) Quoted rate shall deemed to be inclusive necessary internal wiring, excavation, foundation concrete etc.

Earthing with galvanized steel earth plate 60cm X 60cm X 6 mm thick, buried directly in ground(earth pit not less than 2.25 mtr deep below ground level) with the top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanized earth strip 25 mm x 4 mm thick by means of bolts, nuts, check nuts and washers of galvanized iron or steel and earth plate surrounded by packed layers of coal dust and common salt 15 cm thick all around top and bottom all as shown in electrical plate No 3 connected to panel/equipment all as directed including PCC (1: 3:6) type C1 earth pit, cast iron pit cover, funnel with wire mesh,watering pipe 20mm dia light grade grade,1.5mtr long and 40mm bore light grade from earth plate to pole upto the height of 3mtr as protection pipe fixed with 40x3mm flat iron clamps and GI strip connected to on panel and testing on completion including excavation earth work and disposal of surplus soils all as directed by Engineer-in-charge.

PVC insulated, sheathed cable with multistrand copper conductor of size 3 core 6 sqmm complete all as specified

Construction of brick masonnary with full brick valve chamber size of 900x900x900mm internal diemension with earth work on any type of soil , PCC M-10 type C-2 as in foundation , brick work in CM1:4, 15mm thick plaster in CM1:4 internaly and externally , flush pointed in same mortar as work proceeds , 75mm thick PCC coping all around (M-15 with 20mm aggregate ) , flooring shall 40mm thick PCC M-15 (Nominal Mix ) laid over 75mm thick hard core. Top cover shall be made out of 5mm thick MS Plate fixed in MS angle iron frame made out of angle iron size 40x40x6mm with two numbers of hinges on one side and locking arrangement at other side complete including painting with two coats of synthetic enamel paint over a coat of redoxide primer complete all as specified and directed including demolation of old existing Abandoned valve pits

M&L for cutting of existing CI/DI pipe line of 150 mm bore for insertion of 150x150x80 mm Tee in potion with and including Tee, joint, excavation and earth work complete all as specified and directed. Note: (i) Quoted rate shall deemed to be inclusive Tee, excavation & earth work etc.

Cutting of existing road for removing / laying pipe line, depth of cutting not exceeding 60 cm and width 45 cm and filling the of trench of road i.e. excluding top 15cms with existing aggregate obtained from cutting , watered and properly rammed to satisfaction of EIC and finally provide 150 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate to entire width of trench & finally match the top surface to road & disposal of debris to a distance not exceeding 50 Mts and depositing here directed complete all as directed. (Note: Quoted rate is deemed to be inclusive of 150 m thick PCC 1:3:6, cutting any type of road and removal of debris).

EXTERNAL ELECTRIC SUPPLY

Supply, install, testing and commissioning of transformer step down HT 11KV/433V, plinth/platform mounted out door type copper wound with necessary standard fitting of capacity 100KVA , three phase, 4 wire 50 cycles, oil immersed, naturally cooled with external cooling tubes, core type, delta connected on primary (HV) side in accordance with vector symbol DYN-11 (vector group-4) with neutral brought on secondary (LV) side & having tapping's in equal steps of 2.5% from (+/-)2.5% to (+/-) 5% on primary side by means of hand operated off load tap changing gear, so as to vary LT voltage on secondary side including provision of all necessary/ standard fittings all as per IS-1180:2014 with energy efficient level-2 complete including PCC block work masonary foundation of size 1.5m x 1.5m x 1.2m above ground level over 1.9x1.9x0.2m PCC footing using 1:2:4 using 40mm stone aggregate duly rendered and pcc coping 10cm thick of 1:2:4 using 20mm stone aggregate on top of foundation suitable for mounting transformer complete as specified and directed and mainly comprising of :-.

Item No 43 (Contd...) (a) One Cable box on HV side with one set of 11KV HT bushing with brass/gun metal bushing rods complete with nuts and washers. (b) One cable box on secondary (LV) side consisting of 4 Nos porcelain bushings with GM bushing rods complete with GM nuts and washers with one Nos cable gland suitable for reception of outgoing LT XLPE cable of 120 sqmm , 3.5 core. (c ) Oil conservator with filter type, drain valve and oil level gauge. (d) Silica gel dehydrating breather with first fill of silica gel. (e) Explosion vents. (f) Thermometer pocket on tank cover. (g) One No 100mm dia dial type thermometer vapour pressure type having range 0-120 degree centigrade with temp reading pointer, max temp indicator and resetting devices.

Item No 43 (Contd...) (h) Rating plate with terminal markings. (j) Two earthing terminals on tank/tank cover to facilitate fixing of 32 x 6mm GI earth strip. (k) Oil level gauge. (l) Oil drain and filter valves. (m) Oil filler hole with cap/plug . (n) Lifting lugs/hooks fitted with body. (o) Air relief valve plug. (p) Four plain solid cast steel detachable rollers. (q) First fill of fresh oil conforming to relevant IS and tested upto 50 KV dielectric strength. (r) Extra bushing for neutral outside the LT cable box for providing independent earthing for neutral.

Supply, installation ,commissioning and testing of LT fedder pillar 415 Volts, 3 Phase ,50 Hz Outdoor type factory made, hinged double door ,with door open upto 150 degree when swung and doors should automatically come to closed position if not kept open with effort , aldrop bolt locking arrangemnets of size suitable to accommodate the following accessories, however the depth of panel board shall not be less than 500 mm, outer frame made out of 3.15 mm thick MS sheet , inner compartments made out of CRCA sheet 2 mm thick total modular type fabrication with 7 tanks process, IP-54 with coloured insulation sleeve, rubber, insulator outdoor type totally enclosed weather dust and vermin proof as per IS with front opening suitable arrangement having aluminium bus bar of 300 amps capacity for RYB and half for neutral and insulated with insulators, including connecting incoming and outgoing cables necessary PCC 1:3:6 in foundation and made out of 65 x 65 x 6 mm angle iron grouted at ground above 30 cm from ground level. Comprising complete all as specified with the following accessories. Note:1). Cost including necessary internal connection from bus bar to MCCB/MCB connections. 2) GD Drawing for LT feeder pillar should be get approved from Engineer in charge before fabrication. (a) MCCB 160 Amp 4 pole 35 kA - 01 No. as incoming Make: Legrand/ABB/Schneider (b) MCCB 160 Amp 3 pole 35 kA - 01 Nos. as outgoing Make: Legrand/ABB/ Schneider ( c) MCCB 63 Amp 3 pole 35 kA - 01 Nos. as outgoing Make: Legrand/ABB/ Schneider (d) Multification Meter Make L&T/ Legrand/Schneider (e) Phase indication lamps 01 Set (f) Bus bar min 300 Amp Aluminium with R/Y/B coulored for three phases and 150 Amp for Neutral Black colour insulation sleeves - 01 Set. Location: Near Transformer.

Supply, installation ,commissioning and testing of LT fedder pillar 415 Volts, 3 Phase ,50 Hz Outdoor type factory made, hinged double door ,with door open upto 150 degree when swung and doors should automatically come to closed position if not kept open with effort , aldrop bolt locking arrangemnets of size suitable to accommodate the following accessories, however the depth of panel board shall not be less than 500 mm, outer frame made out of 3.15 mm thick MS sheet , inner compartments made out of CRCA sheet 2 mm thick total modular type fabrication with 7 tanks process, IP-54 with coloured insulation sleeve, rubber, insulator outdoor type totally enclosed weather dust and vermin proof as per IS with front opening suitable arrangement having aluminium bus bar of 300 amps capacity for RYB and half for neutral and insulated with insulators, including connecting incoming and outgoing cables necessary PCC 1:3:6 in foundation and made out of 65 x 65 x 6 mm angle iron grouted at ground above 30 cm from ground level. Comprising complete all as specified with the following accessories. Note:1). Cost including necessary internal connection from bus bar to MCCB/MCB connections. 2) GD Drawing for LT feeder pillar should be get approved from Engineer in charge before fabrication. (a) MCCB 160 Amp 4 pole 35 kA - 01 No.as incomingMake: Legrand/ABB/Schneider (b) MCCB 63 Amp 3 pole 35 kA - 03 Nos.as outgoing(InLiving,Dining hall )Make: Legrand/ABB/ Schneider (c) MCCB 40 Amp 3pole 25KA - 01 Nos. as outgoing (Water supply) Make: Legrand/ABB / Schneider (d) MCCB 32 Amp 3pole 25KA - 02 Nos. as outgoing(Street light ) Make: Legrand/ABB/ Schneider (e) Multification Meter Make L&T/ Legrand/Schneider (f) Phase indication lamps 01 Set (g) Bus bar min 300 Amp Aluminium with R/Y/B colored for three phases and 150 Amp for Neutral Black colour insulation sleeves - 01 Set. Location: Near Living accn

Supplying, laying and commissioning of HT XLPE cables, insulated, screened, PVC bedded, galvanized steel strip armoured, earthed, electric power cable with Aluminium conductor, 11 KV grade, 3 Core, 95 Sq.mm cross sectional area laid in trenches / fixed on poles complete all as specified and as directed by the Engineer - in - Charge. Note: Earth work,excavation,cable covers and sand cushioning shall be measured and paid separately.

Supply, laying, jointing, testing 3 1/2 core, cross-sectional area 120 Sq.mm XLPE, insulated outersheathed and innersheathed, galvanised steel armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, conforming to IS: 7098 (Part-I) of 1988 and laid in trenches, pipe, ducts complete all as specified including suitable lugs and glands

All as per item No 50 here-in-before but of size 95 Sqmm 3.5 Core. (Main incoming)

All as per item No 50 here-in-befor but of size 35 Sqmm 3.5 Core. (Bldg 2 sides)

All as per item No 50 here-in-befor but of size 16 Sqmm 4 Core. (Pump house)

All as per item No 50 here-in-befor but of size 10 Sqmm 4 Core. (Street light)

Material and labour for heat shrinkable HT, 11 KV , outdoor type, cable end joint suitable for 11 KV, 3 Phase, AC, 50 Hz, 3 Core, 95/120 Sq.mm, XLPE Cable including jointing materials complete including taking down old end joints all as specified and as directed by EIC

Supply and fix Dropout fuse assembly triple pole mounted on insulator and steel frame with barrel fuse and HT fuse element of 10 Amps of 11 KV working pressure all as directed.

PVC conduit cable 3 core PVC insulated unsheathed multistranded copper conductor of 2.5 sqmm from junction box to fittings including PVC rigid conduit pipe 20mm size all as specified and as directed.

Junction box made out of FRP /SMC sheet ready made of size 300x200x100mm with one MCB DP 32 Amps and with one MCB SP 2.5 Amps 10 KA with 4 way connector fixed to pole by MS clamps 25mmX5mm FI all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 600X600X6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5metres below normal ground level, connected to galvanised earth lead 32x6 mm GI strip means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected or indicated including testing on completion. Incl necessary excavation, earth work, PCC pit,RCC cover ,funnel with watering pipe 20mm bore light grade,GI protection pipe 40 mm bore light grade complete all as specified and as directed by the Engineer - in - Charge

HOT WATER SUPPLY

Supply, install , testing and commissioning of Solar Hot Water System based on direct transfer of heat of capacity 200 LPD with inner GI hot water tank with PUF insulation and outer cover made out of pre-coated GI sheet including ISI marked electric heater back up with adjustable thermostat. The working pressure not less than 0.4 Kgs/Sqcm. The solar collector is high quality vaccum tubes made out of borosilicate, all complete with GI support duly painted

All as per item No 61 here-in-before but of 300 LPD capacity

COOLING APPLIANCES

Supply, install and commisioning of water cooler storage capacity 120 litres and cooling capacity 80 litres with 02 Nos faucets, SS 304 body, R-134a refrigerant electric driven, single phase Single phase, 50 Hz, operating voltage 180-250 Volt complete all as specified . .

Supply and fix voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input voltage variation between 170 V to 250 V with out pout voltage stabilized at 230V with accuracy of +2.5% and capacity 1 KVA complete all as specified

RE-TRANSPLANTATION OF TREES

Labour, Transport & plant tree retranslation of any girth , any type and lead upto 1.0 Km including necessary excavation, refilling and applying fertilizer complete.

ARBORICULTURE

TREES : Digging of pits of size 1x1x1 mtr, removal of debris, weed roots etc.. refilling with good soil and cattle manure in 4:1 ratio, provn of antitermite treatment at plantation time including supply and planting of approved saplings (Coconut, Bottle palm, Manilkara Zapota, Ashoka,Mango,guvava,Red palm etc..) Sapling should be healthy, grown up with good root system and minimum 4 feet ht from ground level after plantation. Maint: including watering loosening of soil fortnightly manuring with fertilizer, trimming, pruning, stacking and spraying of insecticide and fungisides as and when required. Clearing of any type of vegetation in and around the plantation area for a period of 03 years.

Lawn:- Loosening of soil, removing of weed roots and refilling with agricultural soil and cattle manure in the ratio 4:1. Provn of ATT, mixing, leveling and planting of deep mexican grass and maintenance for a period of 03 years.

SHURBS: Digging of pits of size 0.60x0.60x0.60 mtr ,and refilling with good soil and cattle manure in 4:1 ratio, supply and planting of approved species of healthy grown up sapling with good root system minimum 2 feet from ground level (Bougain villa, Song of India,drackenia,Ixora,Ticoma,Nirivim Red etc..) Rest of the activities as per item No 69 here-in-before for a period for 03 years.

Ishan Constructions

Hariom Projects Pvt Ltd