Construction of Work shop and Seminar hall at I.T.I. Santrampur Dist. Mahisagar

No. Figure Amount

1 Excavation for foundation upto 1.50 mt depth including sorting out and 434.20 Cum 278.06

stacking of useful materials and disposing the excavated stuff within all lead

and lift for soft rock not requiring blasting.

2 Excavation for foundation from 1.50 mt to 3.00 mt. depth including sorting out 212.50 Cum 651.26

and stacking of useful materials and disposing the excavated stuff within all

lead and lift for Hard rock.

3 Filling in foundation and plinth with sand in layers of 20 cm thickness 189.20 Cum 479.80

including watering, ramming and consolidating etc. complete.

thickness including watering, ramming and consolidation etc. complete.

5 Anti Termite System : P/L of Permanent piping technology Anti Termite 779.80 Sq.m. 63.63

treatment before flooring work by installing LLDP (Low linear density

Polyethylene) tube of 8 mm O.D.& 6.4 mm I.D. with in Built Pressure

Compensation chip every 30 cm interval in the tube, having working pressure

of 2 kg/cm 2 and release rate of 1.9 ltr/Hour fixed by P-Clip and nails. The

LLDP pipe shall be installed at the entire periphery of the building and at

internal network of building depth of 20 to 200 mm under floor every 2 to

mtr. c/c distance (adjustable as per building layout) & ends of loop pass

through a PVC Elbow of minimum 32 mm ID at junction box of wall and floor

level, entering into a steel reinforced grooved flexible pipe mini. 22 mm LD

leading into junction box and during injecting chemicals for termite control

treatment.

The anti-termite chemical Lmidcloprid 30.5% SC mix as per IS 6313 (part-III)

shall be injected by the pressure pump diluted with water @ 10.5 ml/5ltr of

water at the rate of 2 kg/sq.cm. @ 5 ltr /Smt. the contractor shall submit

approved line plan for piping system and junction boxes dully approved by

Engineer-in-charge with bond of 5 years warranty. (II) Anti Termite chemical

injected area (Chemical injecting including labour cost)

6 Providing and laying controlled cement concrete M-150 and curing complete 29.10 Cum 4022.72

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Foundations and plinth for PCC.

7 Providing and laying controlled cement concrete M-250 and curing complete 85.20 Cum 4734.10

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Foundations, footings & mass concrete.

8 Providing and laying controlled cement concrete M-250 and curing complete 14.00 Cum 7848.80

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Columns upto plinth level.

9 Providing and laying cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 78.20 Cum 3092.22

machine cut stone aggregate 40 mm nominal size) and curing complete

including cost of form work in foundation and plinth.

10 Providing and laying controlled cement concrete M-200 and curing complete 33.40 Cum 7831.36

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Columns for Ground floor.

11 Providing and laying controlled cement concrete M-200 and curing complete 9.90 Cum 7914.44

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Columns for Terrace floor.

12 Providing and laying controlled cement concrete M-250 and curing complete 58.30 Cum 6398.17

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Ground beam and plinth beam.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

13 Providing and laying controlled cement concrete M-150 and curing complete 78.40 Cum 4662.62

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Plinth Slab.

14 Providing and laying controlled cement concrete M-200 and curing complete 52.20 Cum 6364.82

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Beam for Ground floor.

15 Providing and laying controlled cement concrete M-200 and curing complete 6.00 Cum 6934.10

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Chhajja for Ground floor.

16 Providing and laying controlled cement concrete M-200 and curing complete 3.70 Cum 9021.71

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Lintel for Ground floor.

17 Providing and laying controlled cement concrete M-200 and curing complete 115.80 Cum 6776.77

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Ground floor slab.

18 Providing and fixing 90 cm high Stainless steel railing made from anti 6.00 Rmt. 3719.83

corrosive 304 grade S.S. pipe of 50 mm dia. (16 gauge) as hand rail with S.S.

304 grade baluster of 38 mm dia. (16 gauge) as a vertical support fixed in

RCC slab at 1.2m c/c including three horizontal S.S. pipes of 25 mm dia. (16

gauge) at equal distance fixed by 18.75 mm dia (16 gauge) S.S. pipe with

baluster including accessories as per detailed drawing as directed etc.

19 Providing I.S.I. Mark T.M.T. bar Fe-500D reinforcement with fusion bonded 46363.00 Kg. 77.29

epoxy coating not less than 175 micron thickness and upto 300 micron to

reinforcement bars as per IS-13620-1993/ASTM-775M (including testing of

coating at plant and all taxes) for R.C.C. work including bending, binding and

placing in position complete upto floor two level for Ground floor.

20 Providing I.S.I. Mark T.M.T. bar Fe-500D reinforcement with fusion bonded 2722.50 Kg. 79.39

epoxy coating not less than 175 micron thickness and upto 300 micron to

reinforcement bars as per IS-13620-1993/ASTM-775M (including testing of

coating at plant and all taxes) for R.C.C. work including bending, binding and

placing in position complete upto floor two level for Terrace floor level.

21 Providing and laying brick work using common burnt clay building 65.70 Cum 4214.33

conventional type bricks having crushing strength not less than

Kg./Sq.cm. in foundation and plinth in cement mortar 1:6 (1 cement : 6 fine

sand) including the cost of all materials and labour charges etc. complete.

22 Providing and laying brick work using common burnt clay building 147.90 Cum 4496.05

conventional type bricks having crushing strength not less than 35 Kg/sq.cm.

in super structure above plinth level upto floor two level in cement mortar 1:6

(1 cement : 6 fine sand) for Ground Floor including the cost of all materials

and labour charges etc. complete.

23 Providing and laying brick work using common burnt clay building 66.70 Cum 4538.16

conventional type bricks having crushing strength not less than 35 Kg/sq.cm.

in super structure above plinth level upto floor two level in cement mortar 1:6

(1 cement : 6 fine sand) for First Floor including the cost of all materials and

labour charges etc. complete.

24 Providing and laying half brick work using common burnt clay building 12.50 Sq.m. 684.26

conventional type bricks having crushing strength not less than 35 Kg/Sq.cm

in cement mortar 1:4 (1 cement : 4 coarse sand) in cement mortar in super

structure for Ground floor including the cost of all materials and labour

charges etc. complete.

25 Providing and fixing 150 mm wide, approved quality chicken wire mesh at 370.40 Sq.m. 6.00

junction of brick work and RCC work or two dissimilar surfaces, at all heights

fixed by nails, rowal plugs or tag by cement mortar 1:3 before applying the

plaster, including curing etc. complete

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

26 Providing 15mm thick cement plaster in single coat on rough (similar) side of 716.30 Sq.m. 226.01

single or half brick walls / concrete wall for interior plastering and finished

even and smooth along with floating coat of neat cement slurry etc. complete

in Cement mortar 1:4 (1-cement : 4 sand) at Ground floor.

27 Providing 15mm thick cement plaster in single coat on rough (similar) side of 174.00 Sq.m. 273.80

single or half brick walls / concrete wall for interior plastering and finished

even and smooth along with floating coat of neat cement slurry etc. complete

in Cement mortar 1:4 (1-cement : 4 sand) at Terrace floor.

28 Providing 10 mm. thick smooth cement plaster in single coat for plastering on 500.70 Sq.m. 208.97

ceiling and soffits of stairs and finished even and smooth along floating coat

of neat cement slurry in cement mortar 1:4 (1 cement : 4 sand) (1) Plaster at

Ground floor.

29 Providing 20mm thick double coat sand faced cement gutka plaster on walls 628.90 Sq.m. 345.75

with 1 x 1 cm grooves consisting of 12 mm thick backing coat of C.M. 1:3 (1

cement : 3 sand) and 8 mm thick finishing coat of C.M. 1:1 (1 cement :

sand) including 1 cm x 1 cm grooves etc. complete as directed by Engineer-

in-charge.

30 Providing throating or plaster drip and moulding to R.C.C. Chhajja. 79.80 Rmt. 43.05

31 Applying two coats of acrylic lappy - putty & two coats of primer of approved 1391.00 Sq.m. 40.59

brand and manufacture on new wall surface to give an even shade including

thoroughly brushing the surface free from mortar dropping and other foreign

matter and sand papered smooth for all floors.

32 Wall painting (two coats) with plastic emulsion paint of approved brand and 890.30 Sq.m. 82.85

manufacture on undecorated wall surfaces to give an even shade including

thoroughly brushing the surface free from mortar droppings and other foreign

matter and sand papered smooth for all floors.

33 Wall painting (two coats) with plastic emulsion paint of approved brand and 500.70 Sq.m. 88.38

manufacture on undecorated ceiling surface to give an even shade including

thoroughly brushing the surface free from mortar droppings and other foreign

matter and sand papered smooth for all floors.

34 Finishing wall with weather proof exterior 100% acrylic emulsion paint with 628.90 Sq.m. 120.26

one coat of primer on wall surface to give an required shape even shade

after thoroughly brushing the surface to remove all dirt, dust and remains of

loose powdered materials etc. complete for all floors.

35 Providing and filling with good quality sinder (steam coal) as directed by 6.60 Cum 572.06

engineer in charge in sunks in layers of 15 cm thick including watering,

placing, ramming well etc. as directed for all floors.

36 Providing and laying controlled cement concrete M-200 for R.C.C. work and 0.10 Cum 5970.26

curing complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in coping on Ground floor.

37 Providing and fixing 35mm thick solid core wooden flush double shutter 16.00 Sq.m. 3681.81

confirming to IS:2202 & ISI approved manufacturer, finished with 1mm thick

laminates on both sides of shutter, machine glued PVC beading on

periphery, S. S. handles and S. S. fixtures & locking arrangement of standard

make of kich or equivalent, on each shutter, fixed with minimum 4 Nos.

150mm high S.S. hinges. Sample & shade to be approved by the Architect.

Door: D1, D3 & D4

38 Providing and fixing 35mm thick solid core wooden flush shutter confirming to 17.70 Sq.m. 4848.84

IS:2202 & ISI approved manufacturer, finished with 1mm thick laminates on

both sides of shutter, machine glued PVC beading on periphery, S. S.

handles and S. S. fixtures & locking arrangement of standard make of kich or

equivalent, on each shutter, fixed with minimum 4 Nos. 150mm high S.S.

hinges. Sample & shade to be approved by the Architect. Door: D2 & D5.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

39 Providing and fixing window having two shutter glass section and one shutter 36.90 Sq.m. 2597.98

mosquito net extruded colour anodized aluminum section equivalent to Jindal

series E(30 mm) with sections numbered : frame bottom with weep holes-

20737, frame top & side - 20738; shutter top & bottom- 20993, shutter-inter

lock - 20550, shutter side (handle) - 20549, with 5 mm thick transparent

tinted float glass, with rubber gasket, air lock strip and finishing joints with

transparent silicon sealant, with standard extruded colour anodized aluminum

fittings. Window W1, W2 & W3.

40 Providing and fixing standard extruded colour anodized aluminum sections, 32.30 Sq.m. 683.12

with 5mm thick transparent tinted float glass, with rubber gasket, finishing

joints with transparent silicon sealant on both sides. For Fixed Glass.

41 Providing & fixing in position standard extruded approved colour anodized 19.90 Sq.m. 3944.65

Alluminum Ventilator with 3mm thick Bajari figure adjustable tinted louvers

glass fixed to alluminium strip blade including fixtures, fastening, labours and

equipments as per detailed drawing as directed. For Ventilators V1, V2.

42 Providing and laying 24" x 24" Vitrified 8 mm thick tiles flooring over 20mm 532.00 Sq.m. 1467.72

(average) base of cement mortar 1:6 (1 cement : 6 coarse sand) on new

surface or fixing on existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color cement slurry including

finished with flush pointing & cleaning the surface etc. complete for Anti skid.

43 Providing and laying Vitrified tiles 8 to 10 mm thick, 24'' x 24'' in skirting, 32.50 Sq.m. 1592.40

risers of steps and dedo on 10mm thick cement plaster 1:3 (1-cement : 3-

coarse sand) and jointed with white cement slurry.

44 Providing and laying polished Kota stone slab flooring over 20mm (average) 285.20 Sq.m. 1019.39

thick base of cement mortar 1:6 (1-cement : 6 coarse sand) or L.M. 1.1.5 (1-

Lime putty :1.5 - coarse sand) laid over and jointed with grey cement slurry

mixed with pigment to match the shade of slab including rubbing and

polishing etc. complete. (A) 25mm thick.

45 Providing and laying polished kota stone slab 25mm thick in risers of steps, 10.30 Sq.m. 1177.56

skirting, dedo and pillars laid on 10mm thick cement mortar 1:3 (1-Cement :

coarse sand) and jointed with gray cement slurry mixed with pigment to

match the shade of slab including rubbing and polishing etc. complete.

46 Providing and laying Anti skid Ceramic tiles 8mm to 10mm thick, 30cm x 40.80 Sq.m. 1195.54

30cm in flooring treads of steps and landing laid on a bed of 12 mm thick

cement mortar 1:3 (1 cement : 3 coarse sand) finishing with flush pointing in

white cement. Pattern, Colour & Shade approved by Architect or Engineer in

47 Providing and laying Ceramic tiles 6mm thick in flooring treads of steps and 286.30 Sq.m. 1045.60

landing laid on a bed of 12 mm thick cement mortar 1:3 (1 cement : 3 coarse

sand) finishing with flush pointing in white cement.

48 Providing Plinth Protection to building including excavation and laying cement 196.80 Sq.m. 2520.98

concrete 1:3:6 using stone aggregates of 40mm nominal size in foundation

layer 150 mm thick+ 125mm thick sand layer below pre-cast rubber dye inter

locking concrete block 60mm thick with grade of concrete M-300 pneumatic

compressed by mechanically pressed and as per approved design including

75mm sand layer for levelling and filling the joint with sand in proper line and

level etc. complete including providing and fixing precast concrete kerb stone

of grey cement based concrete block 30cm length, 30cm height and 15cm

thick made of M-250 grade concrete as per approved design and including

excavation for fixing in proper line and level, filling the joint with C:M 1:3 (1

cement : 3 fine sand) etc. complete.

49 Providing and laying broken china mosaic flooring for terrace using 12 mm to 823.30 Sq.m. 779.70

20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to

plain or slope and to be tempered to bring mortar creme out upto surface

using white cement including rounding off junctions and extending them upto

15 cm along the wall, clearing with water and oxalic acid etc. as directed.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

50 Providing and laying cement concrete flooring 1:2:4 (1 cement : 2 coarse 823.30 Sq.m. 347.42

sand : 4 graded stone aggregate 20mm nominal size) laid in one layer and

finished with a floating coat of neat cement. (B) 50 mm thick.

51 Providing and fixing mirror polished 18mm thick Granite with full round edge 113.70 Sq.m. 2553.90

and polished of approved quality in cladding on sill and around the doors /

windows / ventilation with 20 mm thick cement plaster CM (1:4) and fixing

with cement slurry & adhesive including moulding of exposed edges as

directed by engineering in charge etc. complete.

52 Providing and fixing M.S. Grills of required pattern to frames of windows etc. 102.80 Sq.m. 3095.77

with M. S. flats at required spacings and frame alround having min. weight of

grill 25 kg/sq.m, square or round bars with round headed bolts and nuts or by

screws including priming coat of approved quality and two coats of enamel

paint, as directed by engineer in charge (A) Plain grill.

53 Providing, erecting and fixing double coated I.S.I. Mark P.V.C. water tank of 4000.00 Litre 3.95

required capacity each with all necessary fittings and connection etc.

complete on terrace as directed.

54 Providing, laying and jointing in true line and level I.S.I. mark 160mm dia. 40.00 Rmt. 834.38

U.P.V.C. pipe (Type B) confirming to IS 13592-1992 with one end plain and

other end socketed with rubbering & fitting conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of

the size 160 mm diameter x 210 mm length x 196 mm height at every

mm center to center or shall be concealed in walls as directed including

necessary fittings such as bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement including cost of all materials.

55 Providing, laying and jointing in true line and level I.S.I. mark 110mm dia. 50.00 Rmt. 876.90

U.P.V.C. pipe (Type B) confirming to IS 13592-1992 with one end plain and

other end socketed with rubbering & fitting conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of

the size 110 mm diameter x 149 mm length x 145 mm height at every

mm center to center or shall be concealed in walls as directed including

necessary fittings such as bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement including cost of all materials.

56 Providing, laying and jointing in true line and level I.S.I. mark 40mm dia. 40.00 Rmt. 148.12

U.P.V.C (Sch-40) for cold water including fitting as approved by Engineer in

charge. Pipe shall be fixed on the wall with held of clamp at every two meter

c/c shall be concealed or open as directed including necessary fitting etc.

including testing of pipe and joints and fixing the same with adhesive solvent

including cost of all materials.

57 Providing, laying and jointing in true line and level I.S.I. mark 25mm dia. 32.00 Rmt. 91.84

U.P.V.C (Sch-40) for cold water including fitting as approved by Engineer in

charge. Pipe shall be fixed on the wall with held of clamp at every two meter

c/c shall be concealed or open as directed including necessary fitting etc.

including testing of pipe and joints and fixing the same with adhesive solvent

including cost of all materials.

58 Providing, laying and jointing in true line and level I.S.I. mark 15mm dia. 60.00 Rmt. 72.65

U.P.V.C (Sch-40) for cold water including fitting as approved by Engineer in

charge. Pipe shall be fixed on the wall with held of clamp at every two meter

c/c shall be concealed or open as directed including necessary fitting etc.

including testing of pipe and joints and fixing the same with adhesive solvent

including cost of all materials.

59 Providing and fixing concealed center point to wall ceiling & floor I.S.I. mark 50.00 Rmt. 447.72

C.P.V.C. (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal

for potable water of following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc. complete. (E) 40mm dia.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

60 Providing and fixing concealed center point to wall ceiling & floor I.S.I. mark 40.00 Rmt. 253.82

C.P.V.C. (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal

for potable water of following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc. complete. (C) 25mm dia.

61 Providing and fixing concealed center point to wall ceiling & floor I.S.I. mark 30.00 Rmt. 170.36

C.P.V.C. (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal

for potable water of following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc. complete. (A) 15mm dia.

62 Providing and laying (to level or slopes) and jointing reinforced concrete light 100.00 Rmt. 678.02

duty non pressure pipes I.S. Class NP-2 of the following internal diameter

with collars and butt ends prepared for collar joints including testing of joints

complete. (D) 300mm dia.

63 Providing, laying and jointing in true line and level I.S.I. mark 75mm dia. 80.00 Rmt. 756.22

U.P.V.C. SWR Type B pipe confirming to IS 13592-1992 with one end plain

and other end socketed with rubbering and fitting conforming to ISI 14735-

1999 of approved make for drainage system pipe line, pipe shall be jointed

with each other with rubber lubricant, pipe shall be fixed on wall using of PVC

clamp at every 2000 mm c/c or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent cement including cost of all

materials.

64 Providing and fixing cast iron spigot and socket soil, waste and ventilating 2.00 No. 741.01

pipes of the following nominal size. (B) 75mm dia.

65 Providing and fixing cast iron spigot and socket soil, waste and ventilating 2.00 No. 892.39

pipes of the following nominal size. (C) 100mm dia.

66 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm 10.00 No. 586.27

diameter with jali of the following nominal diameter of self cleaning design

with C.I. screwed down or hinged grating including the cost of cutting and

making good the walls.

67 Providing and fixing wash down water closet (European type W.C. pan) with 2.00 No. 3631.34

integral P and trap including jointing the trap with soil pipe in cement mortar

1:1 (1 cement : 1 fine sand) including providing and fixing plastic seat cover

for wash down WC with C.P. brass hinges and rubber buffers back plastic

seat and including providing and fixing PVC flushing tank with a pair of C.I. or

M.S. bracket with complete fitting such as lead valve siphon 15 mm dia.

brass ball valve with polythene float C.P. brass handle unions and couplings

for connection with inlet out let and over flow pipes 40 mm dia. porcelain

enameled flush bend including cutting holes in walls and making good the

same connection the flush bend with cistern and closet vitreous china etc.

completed.

68 Provision, supplying and fixing white vitreous china W.C. squatting pan 4.00 No. 1638.03

Orrisa type 580 x 400 size with 100mm P or S trap, 25mm dia. C.P. Brass

flush valve and G.I. inlet connection etc. complete. (A) Vitreous china long

pattern white or color.

69 Providing and fixing brass screw down stop tap. (A) 15mm dia. as approved 4.00 Each 205.83

by Engineer in charge.

70 Providing and fixing ball cock of approved quality as directed. (A) Copper 2.00 Each 189.84

Metal (iv) 50mm dia.

71 Providing and fixing wash basin with single hole for pillar tap with C.I. or M.S. 5.00 Each 1451.48

brackets painted white including sutting holes and making good the same but

excluding fittings. (A) Vitreous China (ii) Flat Back washbasin 550 mm x

400mm size. (i) In white colour.

72 Providing and fixing C. P. brass waste for wash basin or sink. (A) 32mm dia. 5.00 Each 67.91

73 Providing and fixing M.I. fisher union for washbasin or sink. (A) 32mm dia. 5.00 Each 78.75

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

74 Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass 2.00 Each 859.41

mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden

plug with C.P. brass screws and washers.

75 Providing and fixing screw down bib taps of following size.(A) Brass screw 5.00 Each 214.81

down bib tap polished bright. (ii) 20mm dia. as approved by Engineer in

76 Providing and fixing pillar tap, capstan head, screw down high pressure with 5.00 Each 308.73

screws, shanks and back nuts. (i) 15mm dia. as approved by Engineer in

77 Providing and fixing in position 300 mm high, 300 mm wide English / Gujarati 12.00 Each 707.00

letters made from 1.0 mm thick stainless sheet as directed by Engineer-in-

charge with all necessary tools & plants etc. complete.

78 Providing and fixing Urinal of approved quality including connection with trap 4.00 Each 1635.22

and with integral longitudinal flush pipe. (A) Squatting plate pattern white

earthenware 550mm x 300mm.

79 Providing and fixing Rubber plug for sink or wash basin. 5.00 Each 17.15

80 Providing and fixing chromium plated brass half turn flush cock of approved 2.00 Each 263.77

quality including fixing in pipe line etc. complete (ii) 25mm dia.

81 Providing and fixing S.W. Gully trap with C.I. grating brick masonry chamber 10.00 Each 1246.92

and water tight C.I. cover with frame of 300 x 300 mm size (inside) with

standard weight (i) square mouth traps (B) 150 mm x 100 mm size P or R

82 Constructing brick masonry chamber for underground C.I. Inspection 4.00 Each 2932.93

chamber and bends with bricks having crushing strength not less than

Kg/cm2 in C.M. 1:5 C.I. cover with frame (light duty) 455mm x 610mm

internal dimensions total weight of cover with frame to be not less than 38Kg.

(Wt. of cover 23 Kg.) and Wt. of frame 15Kg.) (R.C.C. top slab with 1:2:4 mix

(1-cement : 2 coarse sand : 4 graded stone aggregate 20mm size)

foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3

finished smooth with a floating coat of neat cement on walls and bed

concrete etc. complete. (i) Inside dimensions 455mmx 610mm and 450mm

deep for single pipe line.

83 Constructing brick masonry chamber for underground C.I. Inspection 2.00 Each 3660.76

chamber and bends with bricks having crushing strength not less than

35Kg/Cm2 in C.M. 1:5 C.I. cover with frame (light duty) 455mm x 610mm

internal dimensions total weight of cover with frame to be not less than 38Kg.

(Wt. of cover 23 Kg.) and Wt. of frame 15Kg.) (R.C.C. top slab with 1:2:4 mix

(1-cement : 2 coarse sand : 4 graded stone aggregate 20mm size)

foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3

finished smooth with a floating coat of neat cement on walls and bed

concrete etc. complete. (ii) Inside dimensions 500mm x 700 mm and 450mm

deep for pipe line with one or two inlets.

84 Providing cement vata (10cm x 10cm size) quarter round in cement mortar 145.00 Rmt. 24.28

1:1 including neat cement finishing watering etc. complete.

85 Providing and fixing in position 150 mm high, English letters made from 1.0 30.00 Each 404.00

mm thick stainless steel sheet as directed by Engineer in charge with all

necessary tools & plants etc. complete.

86 Providing and fixing polished 18 mm thick black granite with full round edge 2.20 Sq.m. 2719.93

and double side polished of approved quality in between urinal and fixing with

cement slurry & adhesive including moulding of both exposed edges as

directed by engineering in charge etc. complete.

87 Providing and fixing 0.45 meter wide Drinking platform including supplying 0.90 Sq.m. 3038.08

and fixing granite stone of black or equivalent quality 18 mm thick mirror

polished on top and side position and vertical strip at front with cement slurry

& adhesive including moulding of both exposed edges over 25 mm thick

kotah stone platform fixing in top and sides and intermediates supports fixing

with cement mortar and adhesive and finishing all material and labour and

accessories with necessary fitting complete etc.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

Electrical Items

88 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm 120.00 Pt 485.81

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length, in below type of pipe erected with 6A

Modular type switch / bell push & accessories and earth continuity of

following type, erected on PVC / Metallic / Wooden box, single mounting

base frame covered with textured / metallic / white front plate modules

erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder

/ ceiling rose / H.D. Connector as directed.(f) with medium class rigid PVC

pipe and accessories erected concealed in wall/ceiling complete Cat. III

89 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) 60.00 Pt 674.68

both are of ISI marked 1.1 KV Grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type of pipe erected with 6A

Modular type switch and hum free EME step type electronic fan regulator

mounted and accessories with earth continuity of following type erected on

PVC / Metallic / Wooden box, single mounting base frame covered with

textured / metallic / white front plate modules erected on / in wall / ceiling as

per pipe erected. with necessary ceiling rose / H.D. Connector as directed. (f)

with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete Cat. III

90 Point wiring for Tissino / Modular secondary light point with 2-1.5 sq.mm & 6.00 Pt 167.66

earth wire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multi strand copper wires, in below type of pipe to be erected

complete with earth continuity and necessary connection with primary light

with accessories erected on Metal / PVC / wooden box covered with 3 mm

thick PC (Polycarbonate) / Acrylic sheet for open / concealed wiring. with

necessary Lamp holder / ceiling rose / H.D. Connector as directed. (f) with

medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete.

91 Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both 2.00 Pt 510.05

are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper

wires up to 10 mtr length, in below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on PVC / Metallic / Wooden box

covered with appropriate front plate modules erected on / in wall / ceiling as

per pipe erected with following type of accessories. [I] For 6A Plug and 6 a

switch with 2-1.5 sq.mm Cu. Wire from nearby switchboard / mcb db board

(f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete Cat. III

92 Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin 41.00 Pt 257.55

socket erected on PVC / Metallic / Wooden box, single mounting base frame

covered with textured / metallic / white front plate modules erected on / in wall

/ ceiling with following type accessories Cat. III

93 Providing following type of Modular Type Accessories mounted with PVC / 2.00 Ea 151.50

metallic / Wooden box, single mounting base frame covered with textured /

metallic / white front plate, modules erected with necessary connections as

per site situation directed by Engineer In charge. (1) One No. SP 6 Amp. Cat.

(2) One No 5 pin plug Cat. III 2.00 Ea 151.50

(7) Blank Plate Single Cat. III 64.00 Ea 25.25

(8) Computer RJ-45 socket Cat. III 10.00 Ea 160.59

(9) 16 Amp. SP one way switch Cat. III 16.00 Ea 180.79

(10) 6/16Amp. Universal socket Cat. III 16.00 Ea 199.98

94 Providing & erecting following type of Modular Type Accessories with 10.00 Ea 36.36

necessary connection as desired by Engineer in charge (5) LAN cable

connector with ferule

95 Providing and erecting ISI mark Medium class RIGID PVC PIPES of following 120.00 Mtr. 24.24

size complete to be erected on/in wall or ceiling erected with necessary PVC

fittings & Junction boxes fixed with adhesive solution & clamps with following

dia of pipes, in approved manner as directed (a) 20 mm

(b) 25 mm 30.00 Mtr. 33.33

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

96 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 874.00 Mtr. 82.82

marked stranded Copper conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth

continuity of following size (A) With medium class Rigid PVC pipe and

accessories (b) 2 wire 2.5 sq.mm

97 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 240.00 Mtr. 112.11

marked stranded Copper conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq.mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity of following size

(A) with medium class Rigid PVC pipe and accessories (a) 2 wire 4 sq.mm

(b) 2 wire 6 sq. mm 10.00 Mtr. 147.46

(h) 4 wire 6 sq. mm 285.00 Mtr. 260.58

(i) 4 wire 10 sq.mm (use earth wire of 4 sq.mm) 72.00 Mtr. 425.21

98 Providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi 3.00 Mtr. 37.37

stranded, annealed copper conductor with heat resistant PVC insulated

conforms to IS 694, IEC - 227 erected in existing pipe of following size

(Specifically for control panel, relays, power switchgears, motor starters &

control wiring) with required size of copper lugs, nuts and bolts if required.(d)

One wire 4.00 sq. mm

(e) One wire 6.00 sq. mm 41.00 Mtr. 56.56

(f) One wire 10.00 sq. mm 6.00 Mtr. 91.91

(i) One wire 35.00 sq. mm 4.00 Mtr. 300.98

(k) One wire 70.00 sq. mm 1.00 Mtr. 669.63

99 Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv 22.00 Mtr. 46.46

grade ISI marked copper wires of following size to be erected as directed. (e)

1.50 Sq.mm 3 core round PVC sheathed

100 Supplying & erecting approved make LAN cable of following size in existing 150.00 Mtr. 47.47

pipe as per direction [C] CAT -

101 Providing & erecting Switch board for Computer or electric apparatus 24.00 Ea 1133.22

consisting of following modular type accessories mounted with PVC /

Metallic concealed / open box with single mounting base frame covered with

textured / metallic / white front plate, modules erected with necessary

connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories Cat. III

102 Bakelite adopter for Holder to be erected. 68.00 Ea 9.09

103 Decorative call bell Ting-tong box type 250 volts complete erected 1.00 Ea 71.71

104 Providing & erecting insulated socket 3P+N+E with Plug 32A rating which is 18.00 Ea 2190.69

comprised of Four pole MCB slot and insulated socket. IP40 cat-III

105 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 68.00 Ea 373.70

0.5 Watt assembled on single MCPCB, with housing used as a heat sink

shall be made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium

die cast powder coated and high U.V. & corrosion resistance with diffuser

with company mark/name 160V to 270V, Power Factor more than 0.95, THD

< 15%, CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt, LED LED

driver efficiency > 85% (fitting required LM-79 & LM-80 Certificates) (NOTE:

Below description have shown ranges of Wattage capacity of LED fittings.

shown) (A) Tube Light with integral driver (iv) 22-24 Watts, Surge - 2KV, IP-

20, conventional 4 feet Cat-lll

106 Supplying and erecting led lamps with following wattage capacity of 220 to 7.00 Ea 188.87

240 voltage, minimum 15000 burning hours life, 500 V in built-surge

protection, Polycarbonate diffuser, mounting suitable for E14 / E27 / B22

lamp holders, pf >= 0.5 (A) LED Lamps integral type, with PC diffuser

suitable LAMP holder (iii) 10 to 15 watts Cat-lll

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

107 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 14.00 Ea 427.23

0.5 Watt assembled on single MCPCB, with housing used as a heat sink

shall be made of thick sheet Steel conforming to IS: 513/CRCA / aluminium

pressure die cast powder coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with company mark/name 160V to

270V, Power Factor more than 0.95, THD < 15 %, CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens / watt, LED driver efficiency > 85% (fitting

required LM-79 & LM-80 Certificates) (NOTE: Below description have shown

ranges of Wattage capacity of LED fittings. The Engineer incharge may

shaped Surface / Recessed Mount Downlight with provision for spring loaded

mounting clips complete. IP20 (ii) 11-15 watts, Surge-2 KV Cat-lll

(iv) 22-24 watts, Surge-2 KV Cat-lll 30.00 Ea 758.51

(B) LED Panel Light with provision for Plane front frame with translucent 2.00 Ea 724.17

cover fixed to housing complete.IP20 (v) 24 watts, 12" x 12", Surge-2 KV Cat-

108 Supplying and erecting LED street light / Flood light fittings with High power 11.00 Ea 5599.44

White LEDs wattage of 3 Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or embossed 160 to 270 V, Power

Factor more than 0.95, THD < 10%, CCT 3000 K to 5700K, Uniformity ratio

>0.45, Luminaire efficacy> 100 lumens/watt. LED driver efficiency > 85%.

(fittings required LM-79 & LM-80 certificates) (NOTE: Below description have

shown ranges of Wattage capacity of LED fittings. The Engineer incharge

(IP-65), Surge protection -4KV integral and Light must have 440VAC line

supply with over-voltage protection. (ii) above 48 to 60 Watts Cat-lll

109 Providing and erecting Approved make Four pole moulded case circuit 4.00 Ea 8055.76

breaker having breaking capacity ICU of 35 KA. at 415 V. having normal

current rating 125A. with Fixed thermal & magnetic release suitable to work

on A.C.supply 50 c/s. with all internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing. ICS=100% of ICU only. Cat

110 Providing and erecting Approved make Four pole moulded case circuit 2.00 Ea 16221.61

breaker having breaking capacity ICU of 35 KA. at 415 V. having Normal

current rating 200A.with variable Thermal & magnetic release suitable to

work on A.C. supply 50 c/s. with all internal connections, spreader tinned

copper & complete erected in existing 16 G.M.S.housing ICS=100% of ICU

only. Cat III

111 Providing and erecting Approved make Earth fault Relay suitable to mount 3.00 Ea 4983.34

with inter connection suitable to following size of moulded case circuit

breaker having CT ratio & MCCB rating as following along with shunt trip

220V AC. with all internal connections & complete erected in existing

M.S.housing. (2) 125 A -200 A CT Ratio 1/200

112 Supplying and erecting triple pole & neutral 440V / 500V panel mounting 0.80 Rn. 1961.42

Copper Busbars with four equal Nos. of electrolyte bus having current density Mtr.

not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence of following current

carrying capacity, erected with necessary bus bar supports / insulators, main

cable socket to each bar, erected in existing cubical panel with necessary

connections. (A) Suitable for 100 Amp. capacity

(B) Suitable for 200 Amp. capacity 0.50 Rn. 3202.71

113 Providing and erecting Miniature circuit breaker single pole 0.5A to 2A 11.00 Ea. 270.68

system and having breaking capacity 10 KA to be erected in existing box

confirming to IS 8828/1996 with ISI Mark Cat III

114 Providing and erecting Miniature circuit breaker single pole 6A to 25A 60.00 Ea. 112.11

suitable to operate on 240 V A.C. system and having breaking capacity

KA to be erected in existing box confirming to IS 8828/1996 with ISI Mark Cat

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

115 Providing & erecting 240 V MCB double pole switch for motor & inductive 15.00 Ea. 330.27

load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in

existing box having following capacity (B) 40 Amp. Cat III

116 Providing & erecting 240 V MCB double pole switch for lighting Load (B 3.00 Ea. 278.76

Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box

having following capacity (A) 6 to 32 Amp.Cat III

117 Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve) 6.00 Ea. 578.73

having 10KA breaking capacity & confirms to IS :8828 in existing box having

following capacity (A) 6 to 32 Amp.Cat III

(B) 40 Amp. Cat III 5.00 Ea. 638.32

118 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C 17.00 Ea. 595.90

Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box

having following capacity (a) 6 to 32 Amp. Cat III

(b) 40 Amp.Cat III 19.00 Ea. 668.62

(c) 63 Amp..Cat III 11.00 Ea. 737.30

119 Sheets steel powder coated enclosure suitable for incorporating One/Two 1.00 Ea. 176.75

120 Providing and erecting Sheet Steel powder coated MCB distribution board - 1.00 Ea. 1152.41

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs. (The DBs should be used of same company of

MCB to be used) suitable for (A) single phase incoming and horizontal single

phase outgoing (b) sheet steel double door (IP-43) (iii) 8 way

(B) three phase incoming and single phase horizontal type outgoing Per 3.00 Ea. 2339.16

phase isolation type (PPI) (b) sheet steel double door (i) 4 way

(ii) 6 way 1.00 Ea. 2913.85

121 Providing and erecting Approved make RCCBs conforming to IS:12640 and 7.00 Ea. 1969.50

having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V, 50Hz. having characteristic of

quick action & tripping with all advance feature & do not incorporate any

electronic component for following Max. rating erected as directed (i)

Amps. DP Cat III

(ii) 40 Amps. DP Cat III 6.00 Ea. 2235.13

122 Providing and erecting metallic vitrified danger notice board as per language 2.00 Ea. 69.69

suggested by engineer incharge for MEDIUM VOLTAGE installation to be

erected as per IS-2551.

123 Providing & erecting Medium Voltage Danger Notice Board sticker as per 6.00 Ea. 26.26

language suggested by engineer incharge of standard size as per IS-2551

124 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. 6.00 Kg. 794.87

125 Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms. 2.00 Ea. 368.65

dia. galvanised iron pipe with coupling and buch buried in specially prepared

earth pit complete with necessary 8 SWG earth wire.

126 For using salt and charcoal / coke as required for pipe type earthing. 2.00 Ea. 171.70

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

127 Supplying & erecting earth pit of minimum bore dia.150mm size approved 1.00 Ea. 4591.46

make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I. pipes having Outer pipe dia of

50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-

250 Micron galvanising, connection terminal dia of 12mm with constant

ohmic value surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber and heavy

duty cover. (A) (approved make OEM has to submit test certificate including

value of earth resistance of installation duly stamped and signed by agency

and officer Incharge has to ensure the value of earthing resistane mentioned

in test Certificate) & having back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017,

Voltage drop :- < 1 volt at no load & dry form, Sulphar content:- <2% (C) Back

fill Compound :- Earthing compound should be capable to retain moisture for

long time necessary test report must be submitted by Agency.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

128 Providing & erecting weather proof, dust & vermin proof, floor mounted front 2.60 Sq. 16323.62

operated outdoor type double door cubical panel board necessary IP-54 and Mtr.

above protection as per approval from engineer incharge made from

SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC

M.S.sheet for internal partitions with necessary accesories, supporting

angles/ flats channel including cutting, bending, drilling, welding, riveting with

internal partitions & cable alley as per requirements & instruction of engineer-

in-charge with erection of supplied switch gears, BUSBARS, suitable size of

inter connecting PVC copper wire / copper-aluminium strips, rubber

grommets, rib, bakelite control fuses/MCB for measuring instruments, earth

bus & earth bolts, foundation flange - bolts-base Plates, sufficient nos. of

hinged doors, handles with locking arrangement and rubber gasket, heavy

duty end terminal connection, danger notice board, necessary ventilation,

earthing strip complete.

The Panel shall be painted with epoxy powder coating. (The rates excludes

the cost of switchgears, bus bars, inter connecting mains & Copper

Aluminium strips, meters, Fuses etc. The dimension shall be measured

excluding base beams) The panel shall be supplied with following approved

manufacturers with following size. (B) The standard companies switch gear

shall be used and only manufacturers at CPRI approved factory (i) with

350mm depth

129 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand 154.00 Mtr 284.82

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or

in existing trench / pipe of following size of cables (C) 3 1/2 core 50 Sq.mm

(25 Sq.mm 1/2 core)

(E) 3 1/2 core 95 Sq.mm (50 Sq.mm 1/2 core) 51.00 Mtr 490.86

130 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / 148.00 Mtr 126.25

Solid Aluminium conductor for 1.1 KV. to be laid on wall with necessary

clamps or in existing trench / pipe of following size of cables (B) 4 core

131 Making trench in soft soil of suitable width of 90 cm deep for laying cable or 164.00 Mtr 55.55

locating the fault all over the run and back filling the same and making the

surface as normal ground.

132 Providing & laying.R.C.C. Hume pipe for cable to be laid 90 cm. below 5.00 Mtr 226.24

ground across the road crossing or on floor with necessary material in an

approved manner and making the ground as per original.(F) 100 mm dia.

133 Providing & laying approved make Double walled corrugated pipes (DWC) of 143.00 Mtr 62.62

polyethylene (conforming to IS 14930 II) with necessary connecting

accessories of same material at required depth in existing trench for laying

of cable below ground / road surface for enclosing cable (A) 50 mm outer dia.

(C) 90 mm outer dia. 42.00 Mtr 95.95

134 Providing and fixing heavy duty flange type brass cable gland with rubber ring 22.00 Ea 38.38

for PVC insulated armoured cable complete with out going tails, insulating

tape etc. for following size of cables. (B) 2 to 4 core 6 Sq. mm

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

135 Providing and fixing heavy duty flange type brass double compression type 4.00 Ea 75.75

cable gland with rubber ring for PVC insulated armoured cable complete with

out going tails, insulating tape etc. for following size of cables.(B) 3 & 1/2

core 35/50 Sq.mm

(D) 3 & 1/2 core 95 Sq. mm 4.00 Ea 131.30

136 Solder less crimping type Aluminium lugs conforming to IS suitable for cable 88.00 Ea 6.06

of following size evenly crimped with high pressure tool & connected to

switchgear terminals with brass/cadmium plated nut bolts in an approved

manner. (A) 1.5 / 2.5 / 4 / 6 Sq.mm

137 Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with 55.00 Ea 1948.29

double ball bearing ISI mark with Condenser 230 volt A.C. 50 Hz 1200 mm

sweep complete having 3 blades with aluminium blades with, canopy &

cm. down rod erected with earthing. (Make shall be approved by Engineer in

138 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe 55.00 Mtr 108.07

down rod erected duly painted for fan complete with proper insulation without

leakage and earthing.

139 Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the 71.00 Ea 108.07

RCC bars up to 50mm length each side and pierced through a 16 Gauge

M.S. box / Heavy Duty PVC box complete erected concealed in Ceiling with

necessary finishing.

140 Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan 71.00 Ea 18.18

141 Supplying & erecting approved make low noise decorative exhaust fan 4.00 Ea 1703.87

having square frame ABS body with inbuilt lowers & square frame.200mm

with 1350 RPM Cat.II

142 Supplying & erecting approved make SMC press moulded composite FRP 1.00 Ea 898.90

loop-in, loop-out approx. 2mm thick box complete with Bakelite connector

strip 5way (3P+N+E), DIN rail for mounting mob & hinged doors as per

requirement having locking arrangements with mounting clamp with nuts,

bolts & washers suitable for erection on pole with cable clamps& earth bolt of

following size of box. (A) 300mm x 200mm x 100mm [deep]

(C) 150mm x 125mm x 100mm [deep] 11.00 Ea 476.72

142 Supplying & erecting approved make Digital time switch having lithium cell 6 1.00 Ea 3168.37

years operative and operate battery backup 1 channel day clock with

memory programme, suitable to operate on 240V + 5%, 16A with, floating

contacts Minimum switching setup time 1 minimum & LCD display. Also

comprised permanent ON/OFF switching. Programming switches & housed

in fire proof thermoplastic enclosure & transparent cover erected as required

with necessary connection erected as directed.

143 Supplying & erecting power contactor, AC3 duty for time switch complete 1.00 Ea 857.49

erected as per direction Cat III (C) 4 pole 440V 16 Amp.

144 Supplying and erecting approved make panel mounting type Digital Voltmeter 1.00 Ea 1275.63

having 3 digits LED display, 0 to 750 AC Volts range erected on existing

panel board with all connection, wiring etc. with manufacturers calibration

certificate.

145 Supplying and erecting approved make panel mounting type Digital Ammeter 1.00 Ea 1558.43

having 3 digits LED display, external CT operated, calibrated for 0 to

Amps suitable to operate on 500 Volt AC, erected on existing panel board

with all connection, wiring etc. with manufacturers calibration certificate.

Supply 500 V on existing panel board with necessary connections.

147 Providing & erecting L.T. Current Transformer with bar primary 50/5 to 3.00 Ea 274.72

1000/5 ratio 15 VA burden erected in existing CRCA box duly secured with

insulating materials connected to the meter

148 Supplying and erecting approved make suitable panel indicator LED type 9.00 Ea 43.43

lamp, lens cover, complete erected with necessary connections.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

149 Providing & erecting open well horizontal mono block pump set with cast iron 1.00 Ea 15707.52

body, complete for three phase submersible motor having [C] For 3 HP

phase open well horizontal mono block pump set suitable for 85 LPM to

LPM @ 11 mtr to 33 mtr head suitable for 50/65 mm dia delivery pipe Cat.II

150 Supplying & erecting approved make motor control cubical panel (Direct - on - 1.00 Ea 7722.46

line) made from 16 G. CRCA sheet duly epoxy powder painted inside and

outside with hinged doors and locking, arrangement consisting of suitable

size of ON- OFF isolator (AC - 3/23duty) main fuses, single phasing

preventer, indicating lamps for R- Y - B phases, overload relay, Automatic

incoming, wires duly socket crimped, main contactor & overload relay, start -

stop push buttons, to be erected on angle iron frame grouted on wall as

directed. The isolator, overload relay & contactors will be of L & T, Siemens

or BCH make only. (A) DOL up to 5.0 H.P.

151 Lowering of submersible motor pump set at the depth of following, complete 1.00 Per 856.48

with required. Nos. and size of casing pipes erected by means of proper Job

chain pulley block & pipe wrenches after checking of threads of each pipe

with coupling to take the load of the pump set and pipe assembly filled up

with water (D) For Open well Horizontal submersible pump set for sump well

152 Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible 4.00 Mtr. 104.03

Submersible copper cable approved make of following size. (B) 3 Core x

Total Rs.

i.e. Rs. One Crore Fourty Eight lacs Eighty Five thousand Four hundred Thirty Three and Ninety paisa only.

I/We am/are willing to carry out the work @ ______________ % above/below percent (Should be written

in figures and words) of the estimated rate mentioned above. Amount of my /our tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

Net Rs. ___________________________ Total Rs. ________________________

In words ____________________ In words ____________________

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-

Charge for which no extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills.

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C, Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is

a change as per actual mix design the cost of difference of cement consumption have been deducted from the rate

of original item at the rate of input rate mentioned in all the tender.

5. The Contractor will have to submit the all required mix design at his own cost before execution as directed

and to be approved from the Engineer in charge.

Above all items of "Schedule-B" with Item Description, Unit, Rate & Amount have verified by me and found

Deputy Executive Engineer Sr. Divisional Account Officer Executive Engineer

Lunawada (R & B) Sub Division, Mahisagar (R & B) Division, Mahisagar (R & B) Division,

Lunawada Lunawada Lunawada