IISER-K/CIVIL/24-25/18

Amount

Providing and fixing partition upto ceiling height consisting of G.l. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.l. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture’s specification and direction of engineer in charge all complete. 1.66 mm overall thickness Partition with 8 mm thick double skin Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process with Compressive Strength 225 kg/sq.cm, Bending Strength 100 kg./sq.cm

Providing and fixing thermal insulation with Resin bonded rock wool conforming to IS: 8183, density 48 kg/m3, 50 mm thick, wrapped in 200 G virgin Polythene bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing Gl wire etc. complete as per directions of Engineer-in-Charge.

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc. Sal wood

Providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Marine plywood conforming to IS: 710

Providing & Fixing decorative wpc/ charcoal louvers (any texture) in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality, including cost of adhesive of approved quality.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for Glass doors including necessary cutting and making good etc. complete.

Providing and fixing S. S. (Grade 304) tubular handle bar 32 mm outer dia & 1000 mm long with SS screws etc .complete as per direction of Engineer-in-Charge.

Distempering with 1st quality acrylic Distemper(ready mixed), having VOC (Volatile OrganicCompound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying of water thinable cement primer and additional coats wherever required, to achieve even shade and colour.

Providing and fixing Colour anodised aluminium work for partition made up with aluminium tubular section 1.5"thick. 2.5" x 1.5" as frame, fixed with rawl plugs and screws etc. including cleat angle, aluminium snap beading for glazing/ panelling, panel to be covered with 11 mm thick both side laminated particle board/ 5mm glass including rubber gasket , aluminium snap bidding and taper clip etc. all complete.

Providing and fixing of colour anodised aluminium work for door shutter, frame made up with aluminium tubular section 1 3/4"x1 3/4" as vertical member, top and middle section - 2"x1 3/4", bottom section 4"x 1 3/4" and panel covered as per item no -1, with decorative aluminium handle, hydraulic door closer,neoprene gasket including locking arrangement, stainless steel hinge, screw etc all complete. i) Door shutter (sliding/hinged).

Providing and fixing of frosted films of approved quality on the glass pannels at required position as per direction of Engineer-in-Charge.