Const. of Balance Works of MFSDSAI incl. Internal Electrical, HVAC, Firefighting, Fire Alarm, Lifts, etc. at IIT Roorkee Uttarakhand

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

A SUBHEAD-1 (EARTHWORK)

Carriage of material by mechanical transport including

loading, unloading and stacking

Total earth lead

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas

(exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and

disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over

areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting

out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc.

4 2.25 in layers not exceeding 20cm in depth, consolidated each deposited layer by ramming and 1880.87 cum 253.95 4,77,648.08 - 4,77,648.08

watering, lead up to 50m and lift upto 1.5m.

B SUBHEAD-2 (CONCRETE WORKS)

Providing and laying in position cement concrete of specified grade excluding the cost of

centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone

aggregate 20 mm nominal size derived from natural sources)

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone

aggregate 40 mm nominal size derived from natural sources)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness)

including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or

lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken

floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:

1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone

aggregate 20 mm nominal size derived from natural sources)

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2

7 4.11 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal 10.00 sqm 452.25 4,522.50 - 4,522.50

size derived from natural sources).

Extra for providing and mixing water proofing material in cement concrete work in doses by

weight of cement as per manufacturer’s specification

Digitally signed by ANUJ

Signature of Bidder Page 4 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Providing & Applying a coat of residual petroleum bitumen of grade of VG-10 of approved

9 4.13 quality using 1.7 kg per square metre on damp proof course after cleaning the surface with 10.00 sqm 113.85 1,138.50 - 1,138.50

brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-

III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from

10 4.17 natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed 204.47 Sqm 681.65 1,39,376.98 - 1,39,376.98

and consolidated and grouted with fine sand, including necessary excavation, levelling &

dressing & finishing the top smooth.

Providing and laying in position ready mixed or site batched design mix cement concrete for

plain cement concrete work; using coarse aggregate and fine aggregate derived from natural

sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in

11 4.2 recommended proportions as per IS:9103 to accelerate / retard setting of concrete, to improve

durability and workability without impairing strength; including pumping of concrete to site of

laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and

finishing as per direction of the engineer-in-charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be

payable separately. In case the cement content in design mix is more than 110% of the

minimum specified cement content, the contractor shall have discretion to either re-design the

mix or bear the cost of extra cement.

11.1.1 4.20.1 All works upto plinth level

11.1.1.1 4.20.1.1 Concrete of M10 grade with minimum cement content of 220 kg /cum. 204.29 Cum 8,033.20 16,41,077.17 - 16,41,077.17

C SUBHEAD-3 (REINFORCED CONCRETE WORKS)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15°

landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral

12 5.3 stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, 34.30 Cum 10,719.30 3,67,661.27 - 3,67,661.27

finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from

natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

12.1 5.9 Centering and shuttering including strutting, propping etc. and removal of form for

12.1.1 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete. 397.17 Sqm 307.95 1,22,308.50 - 1,22,308.50

12.1.2 5.9.2 Walls (any thickness) including attached plasters, butteresses, plinth and string courses etc. 1039.70 Sqm 669.55 6,96,131.80 - 6,96,131.80

12.1.3 5.9.3 Suspended floors, roofs, landings, balconies and access platform 184.28 Sqm 766.55 1,41,259.55 - 1,41,259.55

12.1.5 5.9.5 Lintels,beams,plinth beams, girders,bressumers and cantilevers. 20.69 Sqm 608.35 12,586.76 - 12,586.76

12.1.6 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. 1310.40 Sqm 804.25 10,53,889.20 - 10,53,889.20

12.1.7 5.9.7 Stairs, (excluding landings) except spiral-staircases. 54.94 Sqm 657.75 36,136.79 - 36,136.79

12.1.8 5.9.19 Weather shade, Chajjas, corbels etc., including edges. 5.00 Sqm 814.95 4,074.75 - 4,074.75

Extra for additional height in centering, shuttering where ever required with adequate bracing,

13 5.11 propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5

m, for every additional height of 1 metre or part thereof (Plan area to be measured)

13.1 5.11.1 Suspended floors, roofs, landing, beams and balconies (Plan area to be measured). 90.00 Sqm 319.25 28,732.50 - 28,732.50

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in

position and binding all complete upto plinth level.

14.1 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. 22000.00 Kg 89.65 19,72,300.00 - 19,72,300.00

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in

position and binding all complete above plinth level.

Digitally signed by ANUJ

Signature of Bidder Page 5 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

15.1 5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. 131000.00 Kg 89.65 1,17,44,150.00 - 1,17,44,150.00

16 5.30 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 50.00 meter 64.70 3,235.00 - 3,235.00

Providing and laying in position ready mixed or site batched design mix cement concrete for

reinforced cement concrete work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in

recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve

durability and workability without impairing strength; including pumping of concrete to site of

laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing

and reinforcement as per direction of the engineer-in-charge; for the following grades of

17.1 5.33.1 All works up to plinth level.

17.1.1 5.33.1.2 Concrete of M30 grade with minimum cement content of 350 kg /cum 250.00 cum 8,825.35 22,06,337.50 - 22,06,337.50

17.2 5.33.2 All works above plinth level upto floor V level

17.2.1 5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum 929.00 cum 10,306.20 95,74,459.80 - 95,74,459.80

17.2.2 5.33.2.4 Concrete of M40 grade with minimum cement content of 390 kg /cum 250.01 cum 10,730.90 26,82,779.73 - 26,82,779.73

DSR Item Extra For Concrete of M30 grade with minimum cement content of 350 kg /cum in place of

(5.33.2.2- Concrete of M30 grade with minimum cement content of 350 kg /cum

17.2.5 5.33.2.5 Concrete of M50 grade with minimum cement content of 410 kg /cum 500.00 cum 10,872.50 54,36,250.00 - 54,36,250.00

D SUBHEAD-4 (BRICK WORK)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

foundation and plinth in:

18.1 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 2.00 Cum 6,658.25 13,316.50 - 13,316.50

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of

half brick masonry

Brick work with clay fly ash F.P.S. (non modular) brick of class designation 7.5 in

superstructure above plinth level up to floor five level in :

20.1 6.32.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 1.00 Cum 8,190.90 8,190.90 - 8,190.90

Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS

:12894, in super structure above plinth and upto floor V level

21.1 6.45.2 Cement mortar 1:4 (1 cement :4 coarse sand) 2.00 Sqm 969.65 1,939.30 - 1,939.30

Providing and laying autoclaved aerated cement blocks masonry with 100mm thick AAC

blocks in super structure above plinth level up to floor First level in cement mortar 1:4 (1

cement : 4 coarse sand ) The rate includes providing and placing in position 2 Nos. 6 mm dia

M.S. bars at every third course of masonry work.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/ 230mm/300 mm

thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill

23 6.47 level and lintel level with approved block laying polymer modified adhesive mortar all complete 1078.23 Cum 6,994.15 75,41,324.39 - 75,41,324.39

as per direction of Engineer-in- Charge. (The payment of RCC band and reinforcement shall be

made for seperately).

E SUBHEAD-5 (STRUCTURAL STEEL WORK)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work,

24 10.2 including cutting, hoisting, fixing in position and applying a priming coat of approved steel 2834.32 kg 111.95 3,17,302.52 - 3,17,302.52

primer all complete.

Digitally signed by ANUJ

Signature of Bidder Page 6 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc.,

including cutting, hoisting, fixing in position and applying a priming coat of approved steel

primer, including welding and bolted with special shaped washers etc.

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in

26 10.25 position and applying a priming coat of approved steel primer using structural steel etc. as

26.1 10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. 13835.55 Kg 142.30 19,68,798.05 - 19,68,798.05

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of

10mm dia double threaded 6.8 grade (yield strength 480 N/mm2 ), counter sunk head,

comprising of 10m dia polyamide PA 6 grade sleeve, including drilling of hole in frame,

concrete/ masonry, etc.as per direction of Engineer-in-charge

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates

etc., including welding, grinding, buffing, polishing and making curvature (wherever required)

and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing

28 10.28 with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required 1734.48 Kg 612.25 10,61,933.11 - 10,61,933.11

size, on the top of the floor or the side of waist slab with suitable arrangement as per approval

of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be

considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

F SUBHEAD-5 (STONE WORK)

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished)

machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations

of required size of approved shade, colour and texture laid over 20mm thick base cement

mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with

matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to

edges to give high gloss finish etc. complete at all levels.

29.1 8.2.2 Granite stone slab of colour black, Cherry/Ruby red

Providing edge moulding to 18mm thick marble/Granite stone counters, Vanities etc. including

30 8.3 machine polishing to edge to give high gloss finish etc. complete as per design approved by

Engineer-in- Charge.

Extra for fixing marble /granite stone over and above corresponding basic item, in facia and

drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen

platform, vanity counters and similar location in marble/Granite/stone work including

necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc.

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement

: 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete.

33.1 8.9.1 8mm thick

Digitally signed by ANUJ

Signature of Bidder Page 7 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang

saw cut stone with machine cut edges of uniform colour and size upto 1m x 1m,

fixed to structural steel frame work and/ or with the help of cramps, pins etc. and

34 8.20 sealing the joints with approved weather sealant as per Architectural drawing

and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps

and pins etc. shall be paid for separately).

34.1 8.20.2 White sand stone - 30mm thick gang saw cut stone

Providing and fixing structural steel frame (for dry cladding with 30 mm thick gang saw cut

with machine cut edges sand stone) on walls at all heights using M.S. square/ rectangular tube

in the required pattern as per architectural drawing, including cost of cutting, bending, welding

etc. The frame work shall be fixed to the wall with the help of M.S. brackets/ lugs of angle iron/

flats etc. which shall be welded to the frame and embedded in brick wall with cement concrete

block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) of size

300x230x300 mm, including cost of necessary centring and shuttering and with approved

expansion hold fasteners on CC/RCC surface, including drilling necessary holes. Approved

cramps/ pins etc. shall be welded to the frame work to support stone cladding, the steel work

will be given a priming coat of Zinc primer as approved by Engineerin-charge and painted with

two or more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the

Engineer-in- charge for approval before execution). The frame work shall be fixed in true

horizontal & vertical lines/planes. (Only structural steel frame work shall be measured for the

purpose of payment, stainless steel cramps shall be paid for separately and nothing extra shall

Providing and fixing adjustable stainless steel cramps of approved quality, required shape and

size, adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms),

36 8.22 for dry stone cladding fixed on frame work at suitable location, including making necessary 3565.00 Each 365.65 13,03,542.25 - 13,03,542.25

recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium

37 8.32 Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the

building , for all heights and all levels etc. including:

Structural analysis & design and preparation of shop drawings for pressure equalisation or rain

(a) screen principle as required, proper drainage of water to make it watertight including checking

of all the structural and functional design.

Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding

in pan shape in metalic colour of approved shades made out of 4mm thick aluminium

composite panel material consisting of 3mm thick FR grade mineral core sandwiched between

two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet

shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating

of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as

specified using stainless steel screws, nuts, bolts, washers,

cleats, weather silicone sealant, backer rods etc.

Digitally signed by ANUJ

Signature of Bidder Page 8 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with

serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and

anchor bolts of approved make in SS 316, Nylon separators to prevent bi- metallic contacts all

complete required to perform as per specification and drawing The item includes cost of all

material & labour component, the cost of all mock ups at site, cost of all samples of the

individual components for testing in an approved laboratory, field tests on the assembled

working curtain wall with aluminium composite panel cladding, cleaning and protection of the

37.1 (c) curtain wall with aluminium composite panel cladding till the handing over of the building for 1171.68 Sqm 4,474.20 52,42,314.08 - 52,42,314.08

occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s

The Contractor shall provide curtain wall with aluminium composite panel cladding, having all

the performance characteristics all complete , as per the Architectural drawings, as per item

description, as specified, as per the approved shop drawings and as directed by the Engineer-in-

Charge. However, for the purpose of payment, only the actual area on the external face of the

curtain wall with Aluminum Composite Panel Cladding (including width of groove)

shall be measured in sqm. up to two decimal places.

G SUBHEAD-5 (FLOORING WORK)

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished

38 11.3 with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of

steps etc. complete.

38.1 11.3.1 40mm thick with 20mm nominal size stone aggregate. 313.86 Sqm 545.00 1,71,050.98 - 1,71,050.98

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey

cement slurry mixed with pigment to match the shade of the slab including rubbing and

polishing complete with base of

cement mortar 1 : 4 (1 cement : 4 coarse sand) :

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm

40 11.27 (average) thick cement mortar 1:3 (1 cement 3coarse sand) and jointed with grey cement slurry 30.18 Sqm 2,038.55 61,524.48 - 61,524.48

mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

40 mm thick rubbed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1

cement : 5 coarse sand) with joints 3 mm thick, side buttered with cement mortar 1:2 (1 cement

: 2 stone dust) admixed with pigment to match the shade of stone and pointing with same

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved

brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1

cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the

joints with white cement and matching pigments etc. The tiles must be cut with the zero

chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge,

clips of required thickness, leveling system and rubber mallet for placing the tiles gently and

42.1 11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size

Digitally signed by ANUJ

Signature of Bidder Page 9 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the

manufacturer), with water absorption less than 0.08%and conforming to IS: 15622, of approved

brand & manufacturer in all colours and shade in skirting, riser of steps, laid with cement based

high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in

average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made

Providing and fixing removable raised/false access flooring with system and its components of

approved make for different plenum height with possible height adjustment upto 50 mm,

44 11.54 comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame

work and G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as

directed by Engineer-in-charge consisting of:

Providing at required spacing to form modular framework, pedestals made out of GI tube of

thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of

size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size

75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI

Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the

pedestal head in position at the required level. The pedestals shall be fixed to the subfloor

(base) through base plate using epoxy based adhesive of approved make or the

machine screw with rawl plug.

Stringers system in all steel construction hot dipped galvanized of rectangular size

570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the

pedestal head using fully threaded screws ensuring maximum lateral stability in all directions,

the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system

shall provide adequate solid, rigid support for access floor panel, the system shall provide a

minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits

and wiring etc. all complete as per the architectural drawings, as specified and as

directed by the Engineer-in-charge.

Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti

static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel

welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical

cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot

welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel

should be Corroresist epoxy coated for lifetime rust protection and cavity formed by the top and

bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with

(c) lightweight foaming compound. The access floor shall be factory finished with Anti-static High

Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and

Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs

applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on

four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum

1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers

specification and as per the direction of Engineer-in- charge. All specification must be printed

on the side of the panel to ensure the quality of the product.

Digitally signed by ANUJ

Signature of Bidder Page 10 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Providing and laying flamed finish Granite stone flooring in required design and patterns, in

linear as well as curvilinear portions of the building all complete as per the architectural

drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4

(1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement

slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge :

45.1 11.55.1 Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. 373.60 Sqm 2,589.90 9,67,580.52 - 9,67,580.52

Providing and laying Polished Granite stone flooring in required design and patterns,in linear

as well as curvilinear portions of the building all complete as per the architectural drawings

with 18mm thick stone slab over 20mm (average) thick base of cement mortar 1:4 (1 cement:4

coarse sand) laid and jointed with cement slurry and pointing with white cement slurry

admixed with pigment of matching shade including rubbing , curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge.

46.1 11.56.1 Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. 3706.16 Sqm 3,908.80 1,44,86,641.60 - 1,44,86,641.60

H SUBHEAD-5 (FINISHING WORK)

47 13.1 12 mm cement plaster of mix :

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5

coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

49 13.16 6 mm cement plaster of mix :

50 13.37 White washing with lime to give an even shade :

Distempering with oil bound washable distemper of approved brand and manufacture to

give an even shade :

New work (two or more coats) over and including water thinnable priming coat with

52 13.50 Applying priming coat:

With ready mixed pink or Grey primer of approved brand and manufacture on wood work

(hard and soft wood)

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per

53 13.52 manufacturer's specifications including appropriate priming coat, preparation of surface, etc.

Providing and applying two coats of fire retardant paint on cleaned wood/ply surface @ 3.5

54 13.58 sqm per litre per coat including preparation of base surface as per recommendations of 52.80 Sqm 285.80 15,090.24 - 15,090.24

manufacturer to make the surface fire retardant.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to

give an even shade :

Two or more coats on new work over an under coat of suitable shade with ordinary paint of

approved brand and manufacture

Providing and applying white cement based putty of average thickness 1 mm, of approved

56 13.80 brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth 10756.00 Sqm 123.85 13,32,130.37 - 13,32,130.37

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile

57 13.83 Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture,

including applying additional coats wherever required to achieve even shade and colour.

Digitally signed by ANUJ

Signature of Bidder Page 11 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

I SUBHEAD-9 (ALUMINIUM WORK)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with

extruded built up standard tubular sections/appropriate Z sections and other sections of

approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia

and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with

required EPDM rubber/neoprene gasket etc.

Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically

wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P.

brass/ stainless steel screws, all complete as per architectural drawings and the directions of

Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for

58.1 21.1.1 For fixed portion

58.1.1 21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) 678.65 Kg 466.30 3,16,455.66 - 3,16,455.66

Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200mm length), fixed to

roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60 mm long and

stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per

direction of Engineer -in-charge.

Providing and fixing double glazed hermetically sealed glazing in aluminium windows,

ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air

gap, including providing EPDM gasket, perforated aluminium spacers, desiccants,

sealant (Both primary and secondary sealant) etc. as per specifications, drawings and

direction of Engineer-in-

charge complete.

Providing and fixing anodised aluminium grill /louver (anodised transparent or dyed to

required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of

approved design/pattern, with approved standard section and fixed to the existing window

frame with C.P brass/ stainless steel screws @ 200mm centre to centre, including cutting the

grill to proper opening size for fixing and operation of handles and fixing approved anodised

aluminium standard section around the opening, all complete as per requirement and direction

of Engineer-in-charge.

(Only weight of grill to be measured for payment).

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand

and manufacture, including providing and fixing top & bottom pivot & spring type fixing

arrangement and making necessary holes etc. for fixing required door fittings, all complete as

per direction of Engineer- incharge (Door handle, lock and stopper etc.to be paid separately).

Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/

Stone/wood/Ceramic/Gypsum work by providing weather/structural non sag elastomeric PU

sealant over backer rod of approved quality as per architectural drawings and direction of

Engineer-in- charge complete, complying to ASTM C920, DIN 18540-F & ISO 11600

J SUBHEAD-10 (STRUCTURAL GLAZING AND ALUMINIUM COMPOSITE PANEL)

Digitally signed by ANUJ

Signature of Bidder Page 12 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Providing and supplying aluminium extruded tubular and other aluminium sections as per the

architectural drawings and approved shop drawings , the aluminium quality as per grade 6063

T5 or T6 as per BS 1474,including super durable powder coating of 60- 80 microns

conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-

Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for

fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account).

The weight of aluminium extruded section shall be taken for purpose of

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized

65 25.2 system of structural glazing (with open joints) for linear as well as curvilinear portions of the

building for all heights and all levels, including:

Structural analysis & design and preparation of shop drawings for the specified design loads

conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind

pressure without any failure), including functional design of the aluminum sections for fixing

glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets,

screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire

stop (barrier)cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure

equalisation & drainage and protection against fire

hazard including:

Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5

brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement

for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/

masonry/structural steel framework of building structure using stainless steel anchor fasteners/

bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless

steel grade 316, of the required capacity and in required numbers.

Providing and filling, two part pump filled, structural silicone sealant and one part weather

silicone sealant compatible with the structural silicone sealant of required bite size in a clean

and controlled factory / work shop environment, including double sided spacer tape, setting

blocks and backer rod, all of approved grade, brand and manufacture, as per the approved

sealant design, within and all around the perimeter for

Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes,

(d) shapes and profiles, as required as per the site conditions, to seal the gap between the building

structure and all its interfaces with curtain glazing to make it watertight.

Digitally signed by ANUJ

Signature of Bidder Page 13 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Making provision for drainage of moisture/ water that

enters the curtain glazing system to make it watertight, by incorporating principles of pressure

equalization, providing suitable gutter profiles at bottom (if required), making necessary holes

of required sizes and of required numbers etc. complete. This item includes cost of all inputs

of designing, labour for fabricating and installation of aluminium grid, installation of glazed

units, T&P, scaffolding and other incidental charges including wastages etc., enabling

temporary structures and services, cranes or cradles etc. as described above and as specified.

The item includes the cost of getting all the structural and functional design including shop

drawings checked by a structural designer, dully approved by Engineer-in- charge. The item

also includes the cost of all mock ups at site, cost of all samples of the individual components

for testing in an approved laboratory, field tests on the assembled working structural glazing as

specified, cleaning and protection till the handing over of the building for occupation. In the

end, the Contractor shall provide a water tight structural glazing having all the performance

characteristics etc. all complete as required, as per the Architectural drawings, as per item

description, as specified, as per the approved shop drawings and as directed by the

Engineer- in-Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded

aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof

stainless steel wire mesh shall be paid for separately under relevant items under this sub- head.

However, for the purpose of payment, only the actual area of structural glazing (including

width of grooves) on the external face shall be measured in

sqm. up to two decimal places.

Note:-2. The following performance test are to be

conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from

the certified laboratories accreditated by NABL(National Accreditation Board for Testing and

Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is

payable separately.

The NIT approving authority will decide the necessity of testing on the basis of cost of the

work, cost of the test and importance of the work. Performance Testing of Structural glazing

system Tests to be conducted in the NABL accredited lab or any other accreditation body

which operates in accordance with ISO/ IEC

17011 and accredits labs as per ISO/IEC 17025

Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as

per ASTM E- 283-04 testing method for a range of testing limit 1 to 200 mVhr

Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a

range up to 2000 ml.

Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a

range upto 2000 ml

Structural Performance Deflection and deformation by static air pressure test (1.5 times design

4 wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50

Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative

test, Tests to be conducted on site.

65.1 6 Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml 1252.07 Sqm 3,111.35 38,95,615.55 - 38,95,615.55

Digitally signed by ANUJ

Signature of Bidder Page 14 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Extra for openable side / top hung vision glass panels (IGUs) including providing and

supplying at site all accessories and hardwares for the openable panels as specified and of the

approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking

sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/

fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the

approved shop drawings, as specified and as directed by the Engineer- inCharge.

Providing, fabricating and supplying shadow box of required size and shape, for fixing in the

spandrel portion of the structural glazing, in linear as well as curvilinear portions of the

building by providing semi - rigid, inorganic, non-combustible fibre glass wool insulation 50

mm thick, conforming to IS: 8183 and BS: 3958 Part 5. The insulation layer shall have facing

67 25.5 (factory bonded on surface # 1 of the fibre glass insulation layer), of black non-woven fibre 2.88 Sqm 1,954.30 5,628.38 - 5,628.38

glass tissue of nominal thickness 0.5 mm and nominal mass not less than 60 gm /sqm, made of

randomly oriented glass fibres distributed in a binder by a wet-lay process including fixing 1.5

mm thick solid aluminum sheet backing using, 6 mm thick cement board including SS rivets,

nuts, bolts, washers etc complete.

Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened

monolithic float glass of approved colour and shade with reflective soft coating on surface # 2

of approved colour and shade so as to match the colour and shade of the IGUs in the vision

panels etc. ,all complete for the required performances as specified, as per the Architectural

drawings, as per the approved shop drawings, as specified, and as directed by the Engineer-

For payment, only the actual area of glass on face # 1 of the glass panels (but excluding the area

of grooves and weather silicone sealant) provided and fixed in position, shall be measured in

sqm. (Payment for fixing of Spandrel Glass Panels in the curtain glazing is included in cost of

relevent Item*).“(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating

on face # 2, having properties as visible Light transmittance (VLT) of 25 to 35 %, Light

reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25-

0.28) and U value of 3.0 to 3.3 W/m2 K etc. . The properties of performance glass shall be

decided by technical sanctioning authority as per the site requirement.

K SUBHEAD-11 (WATER PROOFING WORKS)

Providing and Placing in position suitable PVC water stops conforming to IS:12200 for

69 22.4 construction/ expansion joints between two RCC members and fixed to the reinforcement with

binding wire before pouring concrete etc. complete :

69.1 22.4.2 Dumb bell with central bulb (180mm wide, 8mm thick). 30.00 Metre 232.05 6,961.50 - 6,961.50

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by

applying cement slurry mixed with water proofing cement compound consisting of applying :

First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound

@ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement

(b) compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with

water curing for 48 hours.

The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions

of pipes and masonry with polymer mixed slurry

Digitally signed by ANUJ

Signature of Bidder Page 15 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Providing and laying integral cement based water proofing treatment including preparation of

71 22.7 surface as required for treatment of roofs, balconies, terraces etc consisting of following

Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water

proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC

slab including adjoining walls upto 300 mm height including cleaning the surface before

Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50%

of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound

conforming to IS : 2645 and approved by Engineerin-charge over 20 mm thick layer of cement

(b) mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound

conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating

similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and

After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of

(c) cement admixed with water proofing compound conforming to IS : 2645 and approved by

Engineer-in-charge.

Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse

sand) admixed with water proofing compound conforming to IS : 2645 and approved by

(d) Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster

and finally finishing the surface with trowel with neat cement slurry and making pattern of

300x300 mm square 3 mm deep.

The whole terrace so finished shall be flooded with water for a minimum period of two weeks

(e) for curing and for final test.“All above operations to be done in order and as directed and

specified by the Engineer-in- Charge :

71.1 22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65 mm. 1117.01 Sqm 1,522.95 17,01,152.95 - 17,01,152.95

72 22.14 Grading roof for water proofing treatment with

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal

L SUBHEAD-12 (WOOD, PVC WORK & FIRE DOORS WORK)

Providing wood work in frames of doors, windows, clerestory windows and other frames,

73 9.1 wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia

& length ( hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed

shutters for doors, windows and clerestory windows (Area of opening for panel inserts

excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled

and glazed shutters 25 mm to 40 mm thick :

74.1 9.7.7 Float glass panes

74.1.1 9.7.7.1 4 mm thick glass pane (weight not less than 10kg/sqm). 0.68 Sqm 1,897.10 1,280.54 - 1,280.54

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-

decorative type, core of block board construction with frame of 1stclass hard wood and well

matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on

both faces of shutters :

75.1 9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 101.64 Sqm 2,015.75 2,04,875.79 - 2,04,875.79

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all

edges of flush door shutters (over all area of door shutter to be measured).

Digitally signed by ANUJ

Signature of Bidder Page 16 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass

excluded) (overall area of door shutter to be measured):

78 9.26 Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). 46.53 Sqm 93.65 4,357.53 - 4,357.53

Providing and fixing wooden moulded beading to door and window frames with iron screws,

plugs and priming coat on unexposed surface etc. complete :

79.1 9.40.1 2nd class teak wood

80 9.75 Providing and fixing bright finished brass door latch with necessary screws etc. complete :

Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair

of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door

closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to

80 kg and door width from 701 mm to 1000mm) with double speed adjustment with necessary

accessories and screws etc. complete.

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six

83 9.103 levers anda pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) 112.00 Each 739.80 82,857.60 - 82,857.60

aluminium lever handles of approved quality with necessary screws etc. complete.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss /

matt / suede finish with high density protective surface layer and reverse side of adhesive

bonding quality conforming to IS : 2046 Type Including cost of adhesive of approved

Providing and fixing factory made uPVC white colour sliding glazed door comprising of uPVC

multi- chambered frame with in-built roller track and sash extruded profiles duly reinforced

with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of

required length (shape & size according to uPVC profile), appropriate dimension uPVC

extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if

required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one

side of extreme panels along with zinc plated mild steel multi point locking having transmission

gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS

85 9.147F 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg),

G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel

screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners,

including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame

the gap between frame and adjacent finished wall shall be filled with weather proof silicon

sealent over backer rod of required size and of approved quality, all complete as per approved

drawing & direction of Engineer-in-Charge. (Single / double glass panes,wire mesh and silicon

sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted

but no extra payment on thisaccount shall be made.

Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in

depth & width of profile shall be acceptable.

Three track three panels sliding door made of (big series) frame 116 x 45 mm & sash 46 x 82

85.1 9.147F.3 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead 14.95 Sqm 6,940.45 1,03,759.73 - 1,03,759.73

of appropriate dimension. (Area of door above 5.00 sqm)

Digitally signed by ANUJ

Signature of Bidder Page 17 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate

made out of 16 SWG G.I.sheet (zinc coating not less than 120gm/sqm) duly filled with

vermuculite based concrete mix, suitable for mounting 120 minutes fire rated door shutters.

86 9.136 The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the 103.60 Metre 1,462.75 1,51,540.90 - 1,51,540.90

frame and fixing with dash fastener of approved size and make, including applying a coat of

approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash

fastener to be paid for separately).

Providing and fixing 50 mm thick glazed fire resistant door shutters of 120 minutes fire rating

conforming to IS:3614 (Part-II) tested and certified as per laboratory approved by Engineer-in-

charge with suitable mounting on doorframe, consisting of vertical styles, lock rail, top rail

87 9.137 100mm wide, bottom rail200mm wide, made out of 16 SWG G.I.sheet (zinc coating not less 69.23 Sqm 6,444.95 4,46,183.89 - 4,46,183.89

than 120 gm/sqm duly filled FR insulation material and fixing with necessary stainless steel ball

bearing hinges of approved make, including applying a coat of approved fire resistant primer

etc. all complete as per direction of Engineer-in charge(pannelling to be paid for separately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with

G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size

20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150

mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less

than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all

respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge

with glass of required thickness having 60 minutes of fire resistance both integrity & radiation

control (EW60) and minimum 20 minutes of insulation (EI20). The manufacturer have to give

test report/certification of fire glass and the glass should have the stamp showing the value ofE,

EW & EI. The glass shall be tested in approved NABL accredited lab or by any other

accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per

ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size

not be more than 1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing panic bar / latch (Double point)

89 9.139 fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand 15.00 Each 7,145.90 1,07,188.50 - 1,07,188.50

and manufacture to be approved by the Engineer- in- charge, all complete.

M SUBHEAD-13 (ROOFING)

Providing gola 75X75 mm in cement mortar 1:2:4 (1 cement : 2 Coarse sand : 4 stone

90 12.21 aggregates 10 mm down ) including finishing with cement mortar 1:3 (1 cement : 3 fine sand )

as per standard design :

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C.

91 12.22 sheet1mx1mx400micron, finished with 12mm cement plaster 1:3 (1 cement :3 coarse sand) and 8.00 Each 266.60 2,132.80 - 2,132.80

a coat of neat cement, rounding the

edges and making and finishing the outlet complete.

Digitally signed by ANUJ

Signature of Bidder Page 18 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium

silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level,

suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @

120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints

to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet,

spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm

(Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a

grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of

0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to

from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle

pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the

help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm

interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved

texture in the grid, including, cutting/ making opening for services like diffusers, grills, light

fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended

from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia

and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of

size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed

with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as

per specifications, drawings and as directed by Engineer-in-Charge.

Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No

deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30

sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection

> 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having

thermal conductivity <0.043w/mv

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI

(solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof

and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1

93 12.55 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in 1139.97 Sqm 1,444.90 16,47,145.09 - 16,47,145.09

ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including

providing skirting upto 150 mm height along the parapet walls in the same

Providing and laying roof insulation with 40 mm thick impervious sprayed, closed cell free

Rigid Polyurethane foam over deck insulation conforming to IS - 12432 Pt. III (density of foam

being 40-45 kg/ cum), over a coat of polyurethane primer applied @ 6- 8 sqm per litre, laying

94 12.56 400 G polythene sheet over PUF spray and providing a wearing course of 40 mm thick cement 1117.01 Sqm 1,363.95 15,23,548.09 - 15,23,548.09

screed 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) in chequered

rough finish, in panels of 2.5 m x 2.5 m and embedding with 24 G wire netting and sealing the

joints with polymerized mastic, all complete as per direction of Engineer-in-Charge.

N SUBHEAD-14 (MISCELLANEOUS NON SCHEDULED ITEMS - CIVIL WORK)

Digitally signed by ANUJ

Signature of Bidder Page 19 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Providing & applying intumescent fire retarding coating of approved make in minimum

thickness of required thickness as per design for fire nrating of 2 hour/120 minutes to exposed

steel work at any height in its finally eracted position as per manufacturer's recommendations

for surface treatment and application including primer cross beams sprayed in position & at site

including all scaffolding, primer, finish coat & ancillary tools machinery required all as per

manufacture's recommendation & certification, etc all completed to the entire satisfaction of

95 N.S Project Manager. Intumescent coating shall be very low VOC, single component, acrylic, 657.40 Sqm 2151.00 - 14,14,061.12 14,14,061.12

intumescent heat insulation paint providing excellent fireproof performance, good film

appearance and easy application providing very effective fire barrier due to high active solid

content of minimum 63% plus munus 4% char strength and nano fillers and shall have

minimum density of 1.30 kg/l intumescent coating shall be such which shall provide fast

development of stable, low heat transfer sa as to provide effective and long term pretection to

flammable and non-flammable substrates.

Providing and Applying passive fire protection complying to UL 263/ ASTM/ BS 476 for

composite steel strcuture by supplying & installing non-corrosive, Spray Applied Cementitious

Fireproofing Vermiculite, consisting of factory controlled premixed cement with a minimum

dry density of 350 kg/cum and installed by manufacturer/ supplier approved applicator. Spray

shall be done in one or more coats of approved make for a two-hour fire protection rating on

structural steel members/sections of different shapes and sizes at all locations. The coating

should be asbestos-free & non- gypsum-based (gypsum-based fireproofing material is not

acceptable). The thickness of fireproofing is to be dependent on Hp/A or W/D or A/P as the

case may be & as calculated by the manufacturer& approved by the Engineer In charge. The

minimum thickness of fire protection coating to be applied on structural steel of different

shapes and sizes shall be 17 mm and above irrespective of as calculated by the manufacturer to

achieve two-hour fire protection and to withstand thermal shocks up to 550 Degree Centigrade.

Structural steel surface members shall be manually cleaned by wire brush to ensure all it is free

of oil, grease, loose mill scale, dirt, dust, or other materials that would impair the bond of

coating to the surfacebefore the application of the fire protection coating. The fire protection

coating of specified thickness shall be achieved by applying the material to the structural steel

surface by spraying method after mixing the material in the recommended quantity of water to

achieve the targeted density. The material thickness should be calculated and shall conform to

fire protection requirements of either BS 276 or UL 263 or ASTM E119 or EN in unrestrained

assembly conditions. The contractor shall furnish test report from the International Test

Laboratory of material before execution of work. Item includes cost of all tools, tackles,

machinery; scaffolding, proper storage of material etc. required to complete activity & nothing

shall be paid extra. Actual surface area of structural steel members shall only be measured for

Digitally signed by ANUJ

Signature of Bidder Page 20 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Providing and fixing of Carpet tile with size of 500X500 mm as per Specification-

1) Yarn / Fibre 100%- Recycled Solution Dyed Nylon

2) Colour System-100% Solution Dyed & 100% Nylon

3) Soil/Stain Protection-Protekt²

4) Preservative Protection-Intersept

5) Tufted Pile Weight -12 - 18 oz/yd² ±5% || 475 - 610 g/m² ±5%

7) Pile Thickness -2 - 3 mm ± 0.5mm

8) Total Thickness - 5-6 mm ± 0.5mm

9)Size Description -25cm X 1m or 500 X 500mm

10) Backing Structure-GlasBac backing with Reinforced Galswwol backing.

11) Adhesive used- Water based Adhesive to be used.

All Complete as per direction of engineer-in charge

Providing and fixing unglazed, uncoated, metal pressed, full body homogeneous anti-algal, all

weather resistant ready to install step tile with built-in- bull nose and anti skid strip, smooth and

anti skid surface confirming to IS: 4457-2007 and having water absorption of <0.05% in 12mm

thickness with size of 2000mm x 300mm, 1520mm x 300mm, 1200mm x 300mm, 920mm x

300mm or in sizes as required as per site condition in treads of stairs. These anti skid tiles are

to be laid on 20mm thick cement mortar of mix 1:4 (1 cement: 4 coarse sand) and joints filled

with polymer based cement grout with all labour, material, cement, tile, sand, grout etc as a

Providing and fixing unglazed, uncoated, metal pressed, full body homogeneous anti-algal, all

weather resistant ready to install step tile with built-in- bull nose and anti skid strip, smooth and

anti skid surface confirming to IS: 4457-2007 and having water absorption of <0.05% in 12mm

thickness with size of 2000mm x 300mm, 1520mm x 310mm, 1200mm x 300mm, 920mm x

300mm or in sizes as required as per site condition in treads of stairs. These anti skid tiles are

to be laid on 20mm thick cement mortar of mix 1:4 (1 cement: 4 coarse sand) and joints filled

with polymer based cement grout with all labour, material,cement, tile, sand, grout etc as a

Providing and fixing unglazed, uncoated, metal pressed, full body homogeneous anti-algal, all

weather resistant ready to install step tile with built-in- bull nose and anti skid strip, smooth and

anti skid surface confirming to IS: 4457-2007 and having water absorption of <0.05% in 12mm

thickness with size of 2000mm, 1520mm, 1200mm, 920mm in length and 150mm-200mm

wide or in sizes as required as per site condition in riser and skirting of stairs. These anti skid

tiles are to be laid on 12mm thick cement mortar of mix 1:3 (1 cement: 3 coarse sand ) and

joints filled with polymer based cement grout with all labour, material, cement, tile, sand, grout

etc as a complete job

Providing and laying full body vitrified tile in floor of minimum thickness 15 mm with water

absorption less than 0.06% and conforming to IS:15622, of approved make, brand and

manufacturer, laid on 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand) jointing

with grey cement slurry @3.30 kg / sqm including grouting the joints with white cement and

100(A) N.S matching pigments etc. The slab must be cut with the zero chipping diamond cutter only. 308.12 Sq.m 3623.95 - 11,16,629.29 11,16,629.29

Laying of slab will be done with the help of notch trowel, wedge, clips of required thickness,

vacuum cups for lifting, leveling system and rubber mallet for placing the slab gently and

Size of tile 800x2400mm of all colours and shades

Digitally signed by ANUJ

Signature of Bidder Page 21 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the

manufacturer),with water absorption less than 0.08% and conforming to IS:15622, of approved

101 N.S brand & manufacturer in all colours and shade in wall cladding ,laid with cement based high

polymer modified quick set tile adhesive (water based) conforming to IS:15477 execution as

per Engineer_in_charge.

Providing and fixing in position Acoustical wall panelling with cladding of walls with fabric

cladded glass wool acoustical panels of 25 mm thickness above 7 feet from floor level and

102 N.S prelaminated MDF/HDF/particle board based perforated acoustic panels fixed on GI sections 114.71 Sq.m 4925.00 - 5,64,936.90 5,64,936.90

upto 7 feet from floor level including GI metal framing in hall and alike locations as per

direction of engineer_in_charge.

Supply and installation at site 35 mm thick GLASS FIBRE REINFORCED CONCRETE JALI,

produced in accordance with PRE CAST INSTITUTE(U.S.A) MANUAL 128 EDN

103 N.S 4,conforming to approved drawings. Product manufactured using compositions of Alkali 0.00 Sqm 3450.00 - - -

Resistant Glass Fibers, High Silica Sand and white cement as raw materials.( Conforming to

relevant Indian and ASTM standards)

Providing and Fixing UniStone CFP – Clay Façade Panelling system in approved shade, finish,

size and in thickness of 15mm. The clay panels shall have Flexural Strength /Modulus of

rupture ≥ 9 N /mm2 in accordance to ISO – 10545 -4 with breaking strength ≥ 550 N in

accordance to ISO 10545-4. The panels should have water absorption ≤ 4 % in accordance to

ISO – 10545-3. The surface scratch hardness value i.e., Moh’s scale should be Minimum 6 in

accordance to ISO -10545-2. The clay panels should have inherent properties of being resistant

to stains and chemicals. The material should be Class I material in terms of reaction to fire in

accordance to EN 13501-1 / ASTM E136. The entire system should be certified by an

approved third-party structural consultant for a minimum structural proof load test with positive

& negative wind pressure of 5kPA.The cladding panels shall be fixed on to existing cured

plastered surface substrate wall treated with one or two coats of primer with appropriate

Aluminium rectangular hollow section vertical members framework of 25mm X 50mm (2mm

thick) which shall be spaced out in accordance to the dimensions of the panel with minimum

104 N.S. spacing of 600mm. The framework shall be attached through L shaped aluminium connectors

of 25mm X 37mm (2mm thick) to the substrate walls. The manufactured panels shall have an

evenly controlled factory – made groove for resting on to a continuous aluminium rail profiles

throughout their length. The profiles are designed and manufactured for starter piece,

intermediate and an inverted starter profile for the top piece. Aluminium rail profile shall

ensure uniform and precision joints and shall be factory finished with Super Durable powered

coated colour in approved RAL shade. All fixtures, and screws shall be corrosion free i.e., all

rail profiles, cleats to be used should be made of 6063 T6 alloy grade and all screws used

should be of Stainless steel of M/s Hilti, Worth, Klimas, Patta or equivalent. The groove of the

width can be chosen i.e., 1.7mm, 3mm, 6.5mm, 12.6mm or 20mm. The corners junctions to be

neatly treated with adequate aluminium closed ‘L’ corner shaped pieces in required length in

similar shadecoated with factory finished Super Durable Powder, to the clay façade panel.

Alternatively, the corners junctions can be treated as regular corner fixing or Mitred corner

fixing. All fixing details and drawings to be provided by vendor and to be duly approved by

All fixing details and drawings to be provided by vendor and to be duly approved by Engineer

104.1 in charge at project.All fixing details and drawings to be provided by vendor and to be duly 1145.58 Sqm 7854.00 - 89,97,383.44 89,97,383.44

approved by Engineer in charge at project.

Digitally signed by ANUJ

Signature of Bidder Page 22 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

FACADE/WINDOW GLASS: Designing, Providing, assembling and supplying vision glass

panels (IGUs) comprising of hermetically-sealed 28mm thick D.G.U. consisting of outer 6mm

high performance toughened green tint glass having performance parameters as mentioned +

16 mm air gap + inner 6mm toughened clear Glass with low ppm level of less than 700 ppm

vision panel units of size and shape as required and specified, of approved colour and shade

with reflective soft coating on surface # 2 , spacer tube 12mm wide, including primary seal and

secondary seal (structural silicone sealant) etc. all complete for the required performances, as

per the Architectural drawings, as per the approved shop drawings, as specified and as directed

by the Engineer-in-Charge. The DGUs shall be assembled in the factory/ workshop of the glass

processor.“(Payment for fixing of DGU Panels in the curtain glazing is included in cost of

relevant item )“For payment, only the actual area of glass on face # 1 of the glass panels

(including the areas of the grooves and weather silicone sealant)provided and fixed in position,

measured in sqm.“.

Providing and applying One coat of natural shade with stone dust tinted trowel texture in

approved shade over a coat of base texture that is a natural shade texture with stone dust

without chips over a coat acrylic primer Mixed with wall sealer along with repair check with

exterior grade cement mixed with primer , one coat of siloxane protection coat to be applied

over this, as directed by Engineer-In-Charge.

EXTERNAL TEXTURE FINISHES : THICKNESS : 1.25 -1.5 MM

Providing & Fixing tegular edge and 15 mm thickness,easily demountable tile , visible surface

of each tile is 7 mm below the grid, manufactured from High density glass wool , visible

surface is a batch painted glass tissue in white, back of the tile covered with glass tissue. Size

Acoustics-Sound absorption(Alpha W) - 0.95 at 200 mm overall depth of system as per EN ISO

354 Acoustics-Sound absorption Class - Class A at 200 mm overall depth of system as per EN

ISO 11654 Acoustics-Articulation class - 180 as per ASTM E1111, ASTM E1110 NRC - 0.9

NRC as per ASTM C 423 Humidity Resistance -Permanent ambient RH up to 95% at 30*C

without sagging, warping and delaminating ( 13964:2014). Fire Safety - Tested and classified

as non combustible according to EN ISO 1182 with reaction to fire classification class A2 s1

d0 according to EN 13501-1 - European Standard. Light Reflectance - 83% light reflectance.

Indoor Health & Well-being - Complying with the French regulation on VOC emissions, A+

level. Certified by the Finnish Building Information Group (RTS) with the M1 label. Free from

107 N.S. substances ofvery high Concern (SVHC) above 100 ppm as defined by the European REACH 543.23 Sqm 1946.00 - 10,57,125.95 10,57,125.95

regulation(No1907/2006).Product Certified under GRIHA council of India for Green Ratings.

Environmental Product declaration (EPD) acc to international ISO 14025 & EN 15804 series

Circularity - Re-cycled content of more than 70%

CE marking - CE-marked according to the harmonised standard EN 13964:2014

Maintenance - Weekly dusting and vacuum cleaning. Framing system - Providing and fixing

Gypsteel pre coated (Exposed portion only) GI T Grid system in 1200/600x600mm module.

Dimensions:- Main Runner ‘T’ section of size 14x32x0.3mm hot dipped galvanized steel body

and capped with precoated of dipped galvanized steel and 3.0 meter long. Cross Runner ‘T’

section of size 14x32mm hot dipped galvanized steel body and capped with precoated of

dipped galvanized steel and 1.2/0.6 meter long.

Perimeter wall angle of hot dipped galvanized steel angle body of size 19x19mm and 3.0 meter

Digitally signed by ANUJ

Signature of Bidder Page 23 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

P/F ceiling Tile of Shapes/Sizes Square 1200x1200 mm; Rectangle 2400x1200 & 1800x1200

mm; Circle Dia. 1200 & 800 mm; Hexagon 1200x1040 mm with 40 mm thickness, Tiles are

demountable, Panel is manufactured from high density glass wool with Akutex FT surface on

both the sides. Edges are straight cut & painted.

Manufacturing- Manufactured in Sweden, production unit is ISO 14001 certified.

Sound Absorption (alpha w) – 1.0

Humidity Resistance -Permanent ambient RH upto 95% at 30 * C without sagging , warping or

delaminating (EN 13964:2014).

Fire Safety -Tested and classified as non combustible according to EN ISO 1182 with reaction

to fire classification class A2 s1 d0 according to EN 13501 -1

Light Reflectance - 85% light reflectance

Indoor Health & Well-being - Complying with the French regulation on VOC emissions, A+

level. Certified by the Finnish Building Information Group (RTS) with the M1 label. Free from

Substances of Very High Concern (SVHC) above 100 ppm as defined by the European

REACH regulation (No1907/2006). Product Certified under GRIHA Council of India for

Green ratings. Environmental Product declaration (EPD) acc to international ISO 14025 & EN

15804 series of standards.

Circularity - Re-cycled content of more than 70%

CE marking - CE-marked according to the harmonised standard EN 13964:2014 Maintenance -

Daily dusting & vacuum cleaning, weekly wet cleaning

Providing & Fixing Wall Paneling size of 1200 x 2700 mm thickness 40 mm natural square

edge. Size of wall panel should be customizable as per the drawings. Tiles are manufactured

from high density glass wool, demountable panels (with standard fabric approved by the

architect) & wrapped around in concealed system with grippers

Acoustics-Sound absorption(Alpha W) - 1 at minimum 50 mm overall depth of system as per

EN ISO 354 Acoustics-Sound absorption Class - Class A at 50 mm overall depth of system as

per EN ISO 11654

NRC – Minimum 0.9 at 50 mm overall depth of system Articulation Class - 230 as per ASTM

E1111, ASTM E1110

Humidity Resistance -Permanent ambient RH upto 95% at 30 * C without sagging , warping or

delaminating (EN 13964:2014).

Fire Safety- Tested and classified as non combustible according to EN ISO 1182 with reaction

to fire classification class A2 s1 d0 according to EN 13501 -1

-European Standard.

Indoor Health & Well-being - Complying with the French regulation on VOC emissions, A+

level.Certified by the Finnish Building Information Group (RTS) with the M1 label. Free

fromsubstances of very high concern (SVHC) above 100 ppm as defined by the European

REACH regulation (No1907/2006). Product Certified under GRIHA Council of India for

Green ratings. Environmental Product declaration (EPD) acc to international ISO 14025 & EN

15804 series of standards.

Circularity - Re-cycled content of more than 70% CE marking - CE-marked according to the

harmonised standard EN 13964:2014

Maintenance - Daily dusting & vacuum cleaning, weekly wet cleaning

Fabric – Fire Retardant Fabric to be applied on the wall panel as approved by architect. Base

fabric considered @ Rs. 700/RMT.

Digitally signed by ANUJ

Signature of Bidder Page 24 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Providing & Fixing of GI Open Cell Laying ceiling tile of size 600mm x 600mm and cell size

of 100mm x 100mm with 60 microns powder coating of polyster paint of dimension 15mm

wide, 38mm height and 0.3mm thick."T" runner with suitably spaced joints to get required

length and of size 15x32mm made from 0.30mm thick (minimum) sheet, spaced at 1200mm

centre to centre and cross "T" of size 15x32 mm made of 0.30 mm thick (minimum) sheet,

1200 mm long spaced between main "T" at 600mm centre to centre to form a grid of 1200 x

600 mm and secondary cross "T" of length 600 mm and size 15x32 mm made of 0.30 mm thick

(minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of

110 N.S. 600x600 mm and wall angle of size 22x22x0.4mm and laying false ceiling tiles of approved 300.61 Sqm 3148.00 - 9,46,319.26 9,46,319.26

texture in the grid including, required cutting/making, opening for services like diffusers,

grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from

ceiling using GI slotted cleats of size 30 x 25 x 1.6 mm fixed to ceiling with 12.5mm dia and

50mm long dash fasteners, 4mm GI adjustable rod with galvanized butterfly level clips of size

85x30x0.8mm spaced at 1200 mm center to center along main T, bottom exposed width of 24

mm of all T- sections shall be pre-painted with polyester paint, all complete for all heights as

per specifications, drawings and as directed by Engineer- in-charge. (supply & Installation of

Providing & Fixing of Aluminium clipin metal ceiling system consisiting of 300 x 1200mm

clipin tile of 60 microns powder coated Aluminium in 0.7mm thickness with beveled edge in

white colour with standard perforataion of 1.8mm dia. The back of the tile should have black

accoustical fleece. The NRC should be 0.70 and suitable for green building application,

Installation: to comprise 3000mm long C' channels spaced at 1200mm centre securely fixed to

the structural soffit by support clamp and approved hangers. The last hanger at the end of each

C channel should not be greater than 600mm from the adjacent wall. Use a C channel

connector for splicing two pcs of C Channel. Ceiling Profile of GI Clip in Metal Ceiling

System of 300x1200 mm module which includes providing and fixing wall angle of size 20x20

111 N.S mm made of 0.4 mm thick pre painted steel along the perimeter of the room with help of nylon 2172.92 Sqm 2603.00 - 56,56,112.74 56,56,112.74

sleeves and wooden screws at 300 mm centre to centre, suspending the main C carrier of size

10x50x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat

37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier

bracket at 1200 mm c/c. Clip in profile main runner having height of 40 mm and width of 19

mm made of GI steel 0.5 mm thick is then fixed to the main C carrier and in direction

perpendicular to it at 600 mm centres with help of suspension brackets & with L profile size of

24x24x0.40mm. Wherever the main C carrier and Clip in Profile have to join, C carrier and

Clip in Profile connectors have to be used, fixing with clip in tiles into Clip in Profile. (supply

& Installation of material)

Digitally signed by ANUJ

Signature of Bidder Page 25 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Supply and fixing of Linear Baffle Ceiling & Wall System:Vertical & horizontal baffle system,

exhibiting space-delineating characteristics as well as acoustic feature (Optional). The system

comprises baffles 50mm wide & 100mm Deep, installed at 100mm C/C distance. The carrier

rails run perpendicular to the baffles. Individual baffle lengths between 600 and 2400 mm can

be selected. Baffle ceiling are supplied with the end cap matching the similar finish of baffle.

Tolerances according to TAIM, DIN EN 13964 and quality controlled to ISO 9001:2015

approved by SIS. Substructure for durlum POLYLAM® Vertical baffle system consisting of U

shaped galvanized slotted carriers minimum 1.2mm Thick installed perpendicularly to baffles at

maximum 1200mm centres using cross connectors. The primary profiles must be connected to

one another with longitudinal splice connectors. The entire ceiling module shall be suspended

with 6mm diameter galvanized steel threaded rods from the true ceiling officially approved

anchor fasteners maximum at 1200mm Centres as per the requirements of DIN EN 13964 and

112 the statics of the system. Customised wall brackets for wall baffles. Ensure horizontal and flush 89.99 Sqm 11025.00 - 9,92,112.19 9,92,112.19

alignment during installation.

Baffle width: 50mm Baffle height: 100mm Individual baffle lengths: Min.600/Max.2400mm

Module: 100mm C/C. Material: Folded GMS .Minimum 0.50mm Thickness

Surface: Digitally printed woodgrain finish. Manufacturer shall have the fully automatic

powder coating system with power and free conveyorize 3mtr/minute capacity. Powder coating

plant shall be equipped with latest modern technology with fully automatic inline Pre-treatment

using nano technology, Inline automatic water Drying system after pretreatment. Finishes of

ceiling planks shall be powder coated base of minimum 60 microns coating thickness. No Pre-

Coated products shall be accepted. The spacing of the grid angles is according to the

requirements of DIN 18168 and DIN EN 13964 and quality controlled to ISO 9001:2015

approved by SIS & LEED certification by Indian Green Building council

Providing and fixing Stain finished Stainless Steel tower bolts Round (barrel type) with

necessary screws etc. complete :

Providing and fixing Stain finished Stainless Steel with Rubber hanging type floor door stopper

with necessary screws, etc. complete.

Extra for providing 5x3 mm Groove to 25 mm thick

Kota & Granite stone staircase Traed etc.

Providing and fixing Stain finished Stainless Steel 316 glass door Floor Lock with screws etc.

Providing and fixing Combi. finished Stainless Steel 316 glass door pull handles 450x25mm

(pair of handle) dia with screws etc. complete :

Supply & fixing Fresh Color Restroom(Toilet) Cubicle made out of Thickness of Compact

Laminate : 18 mm. Size of Cubicle : 1000mm (W) X 1550mm (D) X 2100mm (H),Door Size :

1995mm (H) x 610mm (W),Overall Height of Cubicle : 2100 mm (Including bottom Gap of

100mm) all Including Stainless Steel - 304 Grade accessories,Occupancy Indicator , Rubber

Lining for Groove. all complete as per direction of Engineer-in-charge. (using series floor

Digitally signed by ANUJ

Signature of Bidder Page 26 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Acoustical Door Specification: P/F acoustical doors for the Auditorium. The door to be

fabricated with 12 mm thick marine grade ply and finished with 3-4mm thk veneer (finish with

melamine polish of approved make shade and color and design both side. The door will have

insulation with one layer of 50mm th. 48 kg. Cu. M density fiberglass/rockwool with 8 mm

HDCF Panel having density 1250 kg/m3 . The fiberglass should be supported with wooden

batten of Kail wood frame work minimum 610mm X 610mm to avoid sagging. The door leaf

will be fabricated using 100mm x 74mm th. Teakwood frame. The fixed door frame

(Chowkhat) shall be 2nd class Teakwood of size 125mm x 79mm, the door frame shall be

provided on all four sides. The door will have hydraulic door closer, cross bar door handle and

relevant hardware for fabrication and fixing. The door seal "D" type of rubber seal to block

noise leakage from gap and acoustic door shutter Magnetic type of to be provided all around of

the door frame as shown in the drawing the door to be attached with the door frame by brass

metal hinges with adequate strength and numbers to avoid sagging. All joints to be sealed with

Dow corning 790 or equivalent mastic sealant. Panic bars to be provided on each leaf of the

doors. (Paid Seprately)The doors on the auditorium side to be finished using non light

reflective media like carpet of dull laminate/ veneer.(TWO HOUR FIRE RATED ACOUSTIC

DOOR WITH VISION PANEL , PANIC BAR & INCLUDING ALL NECESSARY

FIXTURES ETC. )

Manufacture, Supply, and Installation of polycarbonate multi-layered, Multicell Connectible

modular panel system, a complete assembly of coextruded UV protected polycarbonate panels

incorporated into a complete system. Standing seam polycarbonate panel system of minimum

25 mm thick (Min.) with min 1200mm (min.) width. Panels with bigger width will be preferred

for reducing number of joints in the roof.

Panels shall be with grip lock double tooth locking mechanism with interlocking connectible

connectors running lengthwise at both sides of the panel. Panels shall be fixed on Purlins of MS

structure (will be paid Separately) with 3 numbers of self-drilling screws and specials

Trapezoidal Heavy Duty Fastener to ensure a pull-out load of min. 7000N (7KN) tested as per

ISO 6892:1998 and IS 1608: 2005. Panels shall be solo opaque type in opaque and translucent

clear combination with seven layers for required lux level along with all fixing accessories to

ensure best performance for wind uplift, vibration, oil canning and visual appearance. Panels

120 N.S with more layers will be preferred for better insulation and improved shading

coefficient. U value shall not be more than 1.6 Watt/m2K as per EN ISO 1077-2:2018 and

respective third Party test certificate shall be produced before procurement. Panels must satisfy

Dart drop impact test as per IS 14443-97 shall show no sign of breakage on Polycarbonate

sheets which have been exposed to UV for a min. of 500 Hours as per ASTM G 155.Panels

shall not have Yellowness Index as per ASTM D 1925 of 15 units when tested on a sample

exposed to UV for 500 Hours as per ASTM G 155.

Panel shall be with additional End cap/Aluminium U/F profile/ Glazing Bar for ends as

required. Panel shall be fixed over MS structural steel/MS purlin (paid separately) conforming

to the detail technical specifications as per approved architectural drawings. Trained and

factory authorized labour with supervision to complete the entire panel installation as per

and direction of the engineering in charge.

Providing and fixing Roller blinds with pelmet/cover in shade and colour all complete as per

direction of Engineer-in-charge.

Digitally signed by ANUJ

Signature of Bidder Page 27 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Supply and fixing of V Shaped Half Elliptical Fin fixed louver comprising 165mm deep

manufactured out of 1mm thick corrosion resistance Aluminium Alloy AA3005 and formed

on a high precision CNC PNEUMATIC CONTROLLED AMADA BRAKE PRESS

MACHINE for smooth appearance. The fin profile is mechanically fixed between aluminium

extruded press plate and continuous assembly channel. The nylon end caps shall be provided on

both sides of the fins. The louver fins will be provided in the module of 300mm C/C. The

louver fin skin shall be Polyester Powder Coated RAL finish suitable for exterior applications

with minimum 80 micron coating thickness. Coating thickness shall be minimum 80 µm and

determined by TAIM standards.

No cracking/ flacking/blistering/chalking for minimum period of 5 Years shall be guaranteed.

Humidity Resistance as per ISO & Salt Spray Test shall be as per ASTM shall be provided. The

122 N.S. factory assembled louver fins of 165mm projection as per the length & 70mm width shall be 418.70 Sqm 3279.00 - 13,72,917.30 13,72,917.30

fixed mechanically to the installation frame of Aluminium/MS provided by others in a module

of 300mm C/C in varying length as per the site requirement to a maximum of 4mtrs.

For LEED certification by Indian Green Building

Council(IGBC) and ISO 9001: 2015 Quality Management System Certification from SIS , ISO

14001:2015, ISO 50001:2018, ROHS Certifications shall be provided. No Coil Coated roll

formed Products acceptable.

Additional framing for suspension shall be installed by others subject to system & wind load as

per the required standard. The erected installation frame shall be aligned within the tolerances

of ± span plumb line and level with a non-cumulative tolerance of a maximum of 2 mm. (Note -

Sub-structure will be paid

in separate item.)

Provinding & fixing Teak Wood CP Wood Step

123 N.S. 300X25X2250 mm wooden planking, tongued and grooved in flooring, including all

asscerioies all complete as per direction of engineer in charge

Extra for tile cutting with water jet all complete as per

direction of Engineer -in -charge

Providing and fixing 1.00 mm thick deck sheeting (including shear connectors/ stud of 19mm

dia. & 110mm height) for RCC slabs as per specifications including fixing the same. The

contractor shall take all precautions to prevent any bending in sheeting.(RCC & R/F shall be

paid seperately). Plan area shall be measured for payment. The vendor must be able to supply

2hr fire rating for deck sheet with concrete. The deck sheet must have minimum zinc coating of

275 g/m2 (Plan Area shall be measured for Payment)

Extra for providing & laying self compaction concrete

126 N.S. in Columns, pillars, piers, abutments, stub columns, posts and struts, offset and projection of 134.32 Cum 285.00 - 38,280.06 38,280.06

columns, lift walls & pits, shear walls etc.M40 grade concrete as per above specifications

Providing and fixing High Strength Friction Bolts (M8.8/10.9) of following grades for

connections, as per structural drawing and as instructed by Project Managers. Rate to include

cost of grouting, MS washer fastening screws/bolts, tightening with nuts and check nuts,

providing necessary holes in shearwalls (if Required), etc.,

Digitally signed by ANUJ

Signature of Bidder Page 28 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Supplying, fabricating, assembling, hoisting/ erecting and fixing in position at all heights and

with all leads, structural steel E350 (In tubes for column, struts, beams, etc.,) all as per

structural drawings and as per detailed specifications (for materials & workmanship) in the

situations described hereinafter including:

The tubes shall be allowed to be made of two rolled sections with maximum 2 side butt

weld i.e. tube made of two C shaped sections. The C sections should be completely rolled

or bent from plates. For smaller tubes, single size butt weld or completely rolled section is

preferred i.e tube made of one open box section which is closed by welding at one corner

only. Other sections like plates, angles, channels can be rolled/fabricated as per structural

drawings and as per detailed specifications (for materials & workmanship) in the

situations described hereinafter

i) Cutting of components to required lengths/ widths and shapes/ profiles.

ii) Smooth grinding/ machining of edges/ faces/ all welding joints.

iii) Preparing the surface to ensure complete removal of mill scale by grit & sand blasting to

achieve finish to grade SA 2.5.

iv) Necessary welding (electric arc welding) for required weld lengths and sizes.

v) Allow for surface preparation, derusting primer coat, three or more coats of synthetic

enamel paint etc. complete all as directed by the Owner.

vi) Providing & Fixing with Anchor Fastener of approved make & size as per drawing &

design wherever required by Project Manager.

Note: The contractor shall submit fabrication drawings for work involved based on

construction drawings (that may be issued during construction period) for approval by the

Owner. The fabrication work shall start only after approval of the fabrication drawings. Any

change required in the fabrication drawings shall be carried out at no extra cost.

128.1 Fabrication shall be in a perfect Architectural workmanship manner and as provided in Section 459000.00 Kg 154.00 - 7,06,86,000.00 7,06,86,000.00

Welding shall be carried out by qualified welders. Electrodes for welding, the procedure,

selection, test and inspection shall confirm to provisions in IS 816, IS 818, IS 822, & IS 833.

Erection/ hoisting shall commence only after passing of fabricated parts by the Owner.

O SUBHEAD-15 (ROAD WORK)

129 16.3 Supplying and stacking at site.

129.1 16.3.4 Over burnt (Jhama) brick aggregate 120 mm to 40 mm 183.72 Cum 974.25 1,78,989.21 - 1,78,989.21

Laying water bound macadam sub-base with brick aggregate and binding material, earth etc.

130 16.5 including screening, sorting and spreading to template and consolidation with light power road-

roller etc. complete.(payment for brick aggregate and moorum etc. to be made separately)

130.1 16.5.1 Over burnt (Jhama) brick aggregate 120 mm to 40 mm 183.72 Cum 725.60 1,33,307.23 - 1,33,307.23

Supplying, stacking and Spreading 6 mm thick red bajri, watering and rolling complete

including preparation of the surface and rolling.

131.1 16.6.1 With road roller/ hand roller 1837.20 Sqm 21.80 40,050.96 - 40,050.96

Digitally signed by ANUJ

Signature of Bidder Page 29 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Providing and laying design mix cement concrete of M- 30 grade, in roads/ taxi tracks/

runways, using cement content as per design mix, using coarse sand and graded stone

aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design

criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading

and compacting mechanically by using needle and surface vibrators, levelling to required slope/

camber, finishing with required texture, including steel form work with sturdy M.S. channel

sections, curing, making provision for contraction/expansion, construction & longitudinal joints

(10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with

approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of

joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately).

Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per

design mix is payable/ recoverable separately.

Cement concrete manufactured in automatic batching plant (RMC plant) i/c transportation to

site in transit mixer

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement

concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1

cement: 3 coarse sand) including making joints with or without grooves (thickness of joints

133 16.69 except at sharp curve shall not to more than 5mm), including making drainage opening 15.90 Cum 8,613.55 1,36,972.76 - 1,36,972.76

wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb

edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to

0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with

water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in

sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10

tonne capacity to achievethe desired density, complete as per specifications and directions of

Engineer-in-Charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path,

park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/

shape, made by table vibratory method using PU mould, laid in required colour & pattern over

50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter

locking paver blocks into the sand bedding layer through vibratory compaction by using plate

vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern,

finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction

of Engineer- in-Charge.

60mm thick Cement concrete paver block of M-35 grade with approved colour, design &

Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel dressed on top,

for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand)

with joints 10mm wide filled with same mortar including ruled pointing etc.

complete as per direction of engineer-in-charge.

P SUBHEAD-16 (PLUMBING WORKS)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan)

with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with

manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures

complete, including cutting and making good the walls and floors wherever required :

Digitally signed by ANUJ

Signature of Bidder Page 30 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

137.1 17.2.1 W.C. pan with ISI marked white solid plastic seat and lid 39 Each 5,540.55 2,16,081.45 - 2,16,081.45

Providing & fixing White colour vitreous china top counter Oval Wash Basin (Size 550

138 N.S. x 400 mm) with CP brass waste assembly complete including CI / MS brackets duly

painted, cutting and making good the walls floors wherever required.

17.11 Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain

with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass

unions complete, including painting of fittings and brackets, cutting and making good the wall

wherever required :

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and

as per the direction of Engineer-in-charge.

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm

with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe,

141 17.5 spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap

with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting

and making good the walls and floors wherever required :

141.1 17.5.2 Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern 29 Each 15,115.40 4,38,346.60 - 4,38,346.60

Providing and fixing 75 mm high, 50 mm deep and 18 mm thick stone slab table rubbed, edges

rounded and polished, fixed in urinal partitions by cutting a chase of appropriate width with

142 8.1 chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction

of Engineer-in-charge and finished smooth.

142.1 8.10.2 Granite Stone of approved shade 29 sqm 3,542.85 1,02,742.65 - 1,02,742.65

Providing and fixing 600 x 450mm beveled edge mirror of superior glass (of approved

143 17.31 quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. 33 Each 1,411.15 46,567.95 - 46,567.95

brass screws and washers complete.

Providing and fixing 450mm long braided hose with two 15mm nuts and rubber washers.

15 mm dia nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved

quality conforming to IS:8931

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S.

146 17.16A triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - 39 Each 299.35 11,674.65 - 11,674.65

Providing and fixing C.P. brass bib cock with wall flange of approved quality

conforming to IS standards.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112

148 17.71 mm distance from wall of standard shape with bracket of the same materials with snap 33 Each 146.30 4,827.90 - 4,827.90

fittings of approved quality and colour, weighing not less than 105 gms.

149 17.34 Providing and fixing toilet paper holder.

18.65 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm,

height of 75mm with concealed fitting arrangements, weighing not less than 106 gms

Providing and fixing of WB 46 x 36 with one pair mounting brackets, EWC & Cistern

151 N.S. complete with fittings & seat cover, one no. hinged rail 76 cm & 4 nos. 4 Each 28,302.00 - 1,13,208.00 1,13,208.00

of grab rails 60 cm.

Digitally signed by ANUJ

Signature of Bidder Page 31 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Supply, Installation, Testing and commissioning of wall hanging drinking online water cooler

(Including RO) with bottle filler facility, made by stainless steel top and heavy duty galvanized

steel frame. With cooling capacity, ADA Compliant, size 472 mm Depth X 447mm width,

flexible bubbler guard , operated between 50 to 120 PSI, Chiller unit Suitable to R134a

Refrigerant, Adjustable thermostat control, suitable for 220-230v/50-60 hz A/C Supply

152 N.S. Complete with all accessories which include MD-CU29, which is an EPA registered 4 Each 1,52,143.00 - 6,08,572.00 6,08,572.00

antimicrobial copper that fights off microorganisms which include MRSA and e-coli. The

water Fountain shall possess NSF-USA, GRIHA, TUV, and to be placed at different

location of building. Agency has to execute all civil work for installing the Water

Fountain/Online water cooler for proper functioning and aesthetic view as directed by the

engineer-in-charge without any extra cost. with 150 ltr Storage capacity.

Providing, fixing and jointing UV stabilized SWR (Type - B) pipes conforming to IS:13592

including all fittings such as bends, clamps, tees, cowls, clean out plugs, offsets, Y-tees,

tees, door fittings, clips, clamps, stays etc. conforming to IS-14735, including jointing with

rubber gasket fixing in sunk areas, Fixing at wall / ceiling level supported by steel clamps

& hangers etc. including Cutting, chases/ holes in floors / walls / slab and making good the

same after pipe have been duly laid and testing complete in all respects.

Providing and fixing in position uPVC SWR floor trap conforming to IS:13592

including providing necessary steel support and as per Specification. Making proper connection

154 cutting chase / hole in floors / slabs and bringing the same in proper condition and

shape after placing the trap in right position complete as required. The hopper and

trap shall be set in cement concrete mix 1:2:4 complete as required.

Providing & fixing PVC EXTENSION PIECE for 100 mm dia floor trap formed out of main

155 N.S. pipe(Type A) with multiple side inlets, suitable for various dia pipes, side connections, 55 Each 1,476.00 - 81,180.00 81,180.00

including all fixtures and fittings as per site conditions and as per standard

Providing and fixing Heavy Class SS grating with Cockroach proof SS strainer of approved

156 N.S. design including setting in floor with cement motor to match with floor finish as per architect 55 Each 1,146.00 - 63,030.00 63,030.00

requirement suitable for waster and FT. Size 100 mm X 100 mm

Providing and fixing Heavy Class SS grating with of approved design including setting in

floor with cement motor to match with floor finish as per architect requirement .

Providing & fixing and jointing UV stabilized uPVC pipes conforming to IS:4985 (working

pressure 6 kg/sqcm.) including all fittings such as bends, clamps, tees,, offsets, Y-tees,

tees, clips, clamps, stays etc. conforming to IS-14735, including jointing with rubber gasket

fixing in sunk areas, Fixing at wall / ceiling level supported by steel clamps & hangers etc.

including Cutting, chases/ holes in floors / walls / slab and making good the same after pipe

have been duly laid and testing complete in all respects.

Providing, fixing and jointing UV stabilized uPVC rain water pipes conforming to IS:4985

(working pressure 6 kg/sqcm.) including all fittings such as bends, clamps, tees, cowls,

159 N.S. clean out plugs etc including Fixing at wall / ceiling level supported by steel clamps &

hangers etc. including Cutting, chases/holes in floors / walls / slab and making good the

same after pipe have been duly laid and testing complete in all respects.

Digitally signed by ANUJ

Signature of Bidder Page 32 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

(I) Single socketed pipes

Providing & fixing P.V.C. WC connector (straight or bend type) with rubber lip ring.

160 N.S. Including 110 mm dia PVC pipe / bend of required length and proper connection with M 39 Metre 295.00 - 11,505.00 11,505.00

seal to C.I. pipe complete as required.

Providing and fixing clean out plug comprising of GI socket caulked to pipe and cast

brass plug with suitable inlet key for opening male threaded joint with GI class 'C' pipe &

socket. Including lead caulked to UPVC pipes complete as

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1

m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a

coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing UPVC floor drain including all fitting and accessories fixed in cement

mortar complete in all respect.

N.S Providing, fixing, testing and commissioning of UPVC inlet fittings with maximum

164 3 inlets 40, 50 & 63 mm OD size UPVC sockets, fixed to UPVC traps including solvent 84 Each 1,357.00 - 1,13,988.00 1,13,988.00

joint/rubber ring joint complete with all civil work.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c

fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings

with one step CPVC solvent cement and the cost of cutting chases and making good the

same including testing of joints complete as per direction of Engineer in Charge. Concealed

work, including cutting chases and making good the walls

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, including all CPVC plain & brass threaded fittings,

166 18.7 including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes &

fittings with one step CPVC solvent cement and testing of joints complete as per direction

of Engineer in Charge.

Internal work - Exposed on wall

167 N.S. Providing and fixing motorized valve of approved quality complete in all respect.

Providing & fixing full way lever operated forged brass ball valve of brass body with

168 N.S. forged brass hard chrome plated steel ball tested to a pressure not less than 10 Kg / sqcm with

threaded / flanged joints complete with nuts, bolts,gaskets, washers etc.

Digitally signed by ANUJ

Signature of Bidder Page 33 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Providing and fixing Butter fly valve with nitrile seat and stainless steel stem with lever

operation and cast iron body in powder coated finish, suitable for test pressure of

10Kg/sq.mm) with flanges, gaskets and necessary pad locking arrangement complete

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making

good the walls etc.

Internal work - Exposed on wall

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready

mixed priming coat, both of approved quality for new work :

Excavating trenches of required width for pipes, cables, etc including excavation for

sockets, and dressing of sides, ramming of bottoms, depth upto

172 2.10 1.5 m, including getting out the excavated soil, and then returning the soil as required, in

layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming,

watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :

172.1 2.10.1 All kinds of soil

172.1.1 2.10.1.2 Pipes, cables etc. exceeding 80mm dia. But not exceeding 300mm dia. 473 Metre 417.35 1,97,406.55 - 1,97,406.55

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of

173 19.1 cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of

joints etc. complete :

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded

174 19.2 stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per

standard design :

Digitally signed by ANUJ

Signature of Bidder Page 34 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Providing and fixing square-mouth S.W. gully trap grade ‘A’' complete with C.I. grating, brick

masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the

weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard

175.1 19.4.1 100x100 mm size P type

175.1.1 19.4.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 6 Each 2,453.55 14,721.30 - 14,721.30

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars

176 19.6 jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine

sand) including testing of joints etc. complete.

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement

177 19.27 mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating

with frame complete as per standard design :

177.1 19.27.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 8 Each 5,589.45 44,715.60 - 44,715.60

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded

178 19.3 stone aggregate 40 mm nominal size) up to haunches of S.W./ R.C.C pipes including bed

concrete as per standard design

Constructing brick masonry manhole cement mortar 1:4 (1 cement: 4 coarse sand) R.C.C.

top slab with 1:2:4 mix (1cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal

size), foundation concrete 1:4:8 mix (1cement: 4 coarse sand: 8 graded stone aggregate 40

mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3

coarse sand) finished with floating coat of neat cement and making necessary

channels in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate

20mm nominal size) finished with a floating coat of neat cement complete as per

standard design.

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm

179.1 19.7.1 internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover

23 kg and weight of frame 15 kg) :

179.1.1 19.7.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 10 Each 11,687.10 1,16,871.00 - 1,16,871.00

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty)

180 19.7.2 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of

cover 58 kg and weight of frame 58 kg) :

With common burnt clay F.P.S. (non modular)

bricks of class designation 7.5

181 19.8 Extra depth for manholes

181.1.1 19.8.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 4 Metre 8,127.45 32,509.80 - 32,509.80

182.1 19.8.2.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 4 Metre 9,744.25 38,977.00 - 38,977.00

Digitally signed by ANUJ

Signature of Bidder Page 35 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Providing orange colour safety foot rest of minimum 6 mm thick plastic

encapsulated as per IS: 10910 on 12 mm dia steel bar conforming to IS : 1786 having minimum

cross section as 23 mm x 25 mm and over all minimum length

263 mm and width as 165 mm with minimum 112 mm space between protruded

legs having 2 mm tread on top surface by ribbing or chequering besides necessary and

183 19.16 adequate anchoring projections on tail length on 138 mm as per standard drawing and 50 Each 487.10 24,355.00 - 24,355.00

suitable to with stand the bend test and chemical resistance test as per specification

and having manufacture's permanent identification mark to be visible even after fixing,

including fixing in manholes with 30 x 20 x 15 cm cement concrete block 1:3:6 (1

cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per

Material & labour for constructing Silt trap of size 1500mm x 3000mm x 2000mm deep

in brick masonry with bricks of class designation 7.5 in cement mortar 1:6 (1 cement: 6

coarse sand) including necessary excavation and foundation concrete 150mm thick in 1:3:6

(1 cement : 3 coarse sand : 6 graded stone aggregate of 40mm nominal size), inside plaster

184 N.S. 12mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) finished with a floating 1 Each 2,77,398.00 - 2,77,398.00 2,77,398.00

coat of neat cement, C.C. floor, RCC slab in mix 1:2:4 & RCC baffle wall including

reinforcement, centering & shuttering etc. and SFRC manhole cover and frame 610 x 455

mm heavy duty HD 10 conforming to IS: 12592 complete in all respects as shown on

Material and labour for Constructing Brick masonry percolation pit 3m dia and 5m deep with

bricks of class designation 7.5 in cement mortar 1:6, base concrete 1:3:6 below the brick

wall, including cost of necessary excavation in any type of soil, back filling as required in

20cm thick layers, dewatering if any, shuttering and shoring and disposal of surplus

excavated material within the plot. 2 nos. 300mm dia borings to a depth of 50 metre (to be

measured from the bottom of the percolation pit), provisioning and fixing 160 O.D. PVC pipes,

tested to 6kg/sqcm, in each bore and upto the height of 300mm above the RCC top

slab. The PVC pipe shall be slotted except 3.0 metres at the top and

3.0 metres below from the bottom of the percolation pit, which shall be blind. Top of the

PVC pipe shall be covered with PVC Socket & plug. Each bore around the PVC pipe

shall be filled with pea gravels. The percolation pit shall be filled with river stone/pebbles as

shown in drawings.

The top slab shall be 150mm thick with RCC (1:2:4) including nominal

reinforcement and 2 nos. heavy duty 560 dia SFRC manhole covers with frames as per

IS:12592 (weight not less than 182 kg) shall be provided in the top slab. PVC encased

185.1 12mm dia steel bar Footrests shall be provided 300 centre to centre. The above shall be 1 Each 4,42,657.00 - 4,42,657.00 4,42,657.00

provided all as specified and shown on drawings. 300mm dia RCC pipe for inlet and

overflow as shown on drawings

shall be measured separately.

Making connection of drain or sewer line with existing manhole including breaking into

and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand

186 19.21 : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with

cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat

cement and making necessary channels for the drain etc. complete :

Digitally signed by ANUJ

Signature of Bidder Page 36 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Excavating trenches of required width for pipes, cables, etc including excavation for

sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out

187 2.10 the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in

depth, including consolidating each deposited layer by ramming, watering, etc. and disposing

of surplus excavated soil as directed, within a lead of 50 m :

187.1 2.10.1 All kinds of soil

187.1.1 2.10.1.1 Pipes, cables etc, not exceeding 80 mm dia. 200 Metre 255.55 51,110.00 - 51,110.00

188 18.12 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.

18.4 Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1

cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with

hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone

190 18.32 aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1

cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering

with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of

neat cement complete as per standard design :

190.1 18.32.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 2 Each 1,712.15 3,424.30 - 3,424.30

Providing and filling sand of grading zone V or coarser grade alround the G.I.

pipes in external work.

Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested

192 18.60 by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required

will be paid separately) :

Making connection of G.I. distribution branch with G.I. main of following sizes by providing

193 18.13 and fixing tee, including cutting and threading the pipe etc.

Digitally signed by ANUJ

Signature of Bidder Page 37 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Design fabricate, deliver (to job site) and install side hung openable aluminium window system

with top and bottom fixed units as per the architectural view. Framing members shall bew 6060

T66 or 6063 16. Aluminium brackets to be 6061-T6 or approved equivalent. The vertical

member should not deflect more than L/175 or 19 mm. whichever is the least for a wind load

(to be calculated as per IS 875 Part 3). The horizontal member should not deflect more than 3

mm. due to dead load and 15 mm. due to wind load of (to be calculated as per IS 875: Part 3).

The system should accommodate DGU as specified in vision areas (refer glazing specification

mentioned as a seperate BOQ item). The basic depth shall be 48 mm., with a vent frame view

width of 19 mm. All gaskets to be EPDM. A secondary window system should also be provided

to holds an openable mesh shutter. The mesh should be of SS 304/316 grade. All exposed

profiles should be powder coated to a minimum of 60 microns. All anchor fasteners to be made

of SS 304 grade. All shims to be capable of transferring the load evenly and made of a suitable

material (GI, Teflon etc.). Capable of lasting the life span of the system. All miscellaneous

items such as peripherals, sealants, backer rods, flashing, fasteners, brackets etc. to be included

in the rate. Performance requirements - 1. The system should have been tested by an

independent internationally accredited third party testing laboratory. 2. The system should

comply to Air infiltration requirement of +/-600Pa when tested in accordance with EN 12207.

3. The system should comply to static water penetration of 600 Pa, when tested in accordance

with EN 1027/ EN 12208. 4. The system should be designed to meet a design wind load of 2.4

kPa and a proof load of 1.5 times the design load. 5. The system should be capable of passing a

repeat air infiltration of +/- 600 Pa. Static water of 600 Pa after wind load test for design load

(to be calculated as per IS 875 Part 3). System and typology detailing: 1. Architectural: The

side-hung windows will have two openable vents to the top and a fixed light at the bottom. 2.

Hardware: All hardware to be procured by system manufacturer to ensure performance. #.

Hardwares include but not limited to hinges, Opening limiters / limiting stays, Engagement

blocks, Locking bars and keeps.

Design Fabricate, deliver (to job site) and install Fixed aluminium system window. The system

to be pressure equalised, ventilated and drained. The outer frame and vent frame should be

made of Aluminium Alloy 6063 T6 with a depth of 40mm. The vertical member should not

deflect more than L/175 or 19mm whichever is the least for a wind load(to be calculated as per

IS 875 part 3). The horozontal member should not deflect more than 3mm due to dead load and

15mm due to wind load(to be calculated as per IS 875 Part 3). The system should accommodate

24mm DGU (6mm Toughened glass+ 12mm Air Space+ 6mm Heat strengthened galss)) in

vision areas (refer glazing specification mentined as a separate BOQ item). All gaskets to be

EPDM. All exposed profiles should be powder coated to a minimum of 60 microns. All anchor

fasteners to be made of SS 304 grade. All shims to be capable of transferring the load evenly

195 NS and made of a suitable material (GI, Teflon etc.) capable of lasting the life span of the system. 3.46 sqm 25,349.56 - 87,709.48 87,709.48

System should be able accommodate surface applied decorative Georgian bars fixing. All

miscellaneous such as peripherals sealants, backer rods, flashing, fasteners, brackets etc. to be

included in the rate. Performance requirements - 1. The system should have been tested by an

independent internationally accredited third party testing laboratory. 2. The system should

comply to Air infiltration requirement of +/-600Pa when tested in accordance with EN 12207.

3. The system should comply to static water penetration of 600 Pa, when tested in accordance

with EN 1027/ EN 12208. 4. The sysytem should be designed to meet a design windload of 2.4

kPa and a proofload of 1.5 times the design load. 5. The sysytem should be capable of passing a

repeat air infiltration of +/-600 Pa. Static water of 600 Pa after windload test for design load (to

be calculated as per IS 875 Part 3).

Digitally signed by ANUJ

Signature of Bidder Page 38 of 90 GULIA Signature of NBCC

BILL OF QUANTITIES (CIVIL WORKS & PLUMBING WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2021 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and

repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2

coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as

to make it leak proof.

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS :

10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23

mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112

mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering

197 19.16 besides necessary and adequate anchoring projections on tail length on 138 mm as per standard 8.00 Each 487.10 3,896.80 - 3,896.80

drawing and suitable to with stand the bend test and chemical resistance test as per

specifications and having manufacture's permanent identification mark to be visible even after

fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement

: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Digitally signed by ANUJ

Signature of Bidder Page 39 of 90 GULIA Signature of NBCC

NBCC (INDIA) LIMITED

(A Govt.of India Navratna CPSE)

NAME OF THE WORK :-CONSTRUCTION OF BALANCE WORKS OF MEHTA FAMILY SCHOOL OF DATA SCIENCE AND ARTIFICIAL

INTELLIGENCE (MFSDSAI) INCLUDING INTERNAL EL, HVAC, FIREFIGHTING, FIRE ALARM, LIFTS, AUDIO VISUAL SYSTEM, CCTV AND

BMS INSTALLATION AND DEVELOPMENT WORKS AT I IT ROORKEE, UTTARAKHAND

NAME OF CLIENT :- IIT ROORKEE

NAME OF THE BIDDER :-

SUMMARY SHEET- ELECTRICAL WORKS

SI. NO DESCRIPTION OF ITEM

DSR N.S.I. Total

1 Conference Room 28 PAX (SUBHEAD-1) ₹ 0.00 ₹ 16,77,516.07 ₹ 16,77,516.07

3 Conference Room 16 PAX (SUBHEAD-3) ₹ 0.00 ₹ 2,63,506.98 ₹ 2,63,506.98

4 BUILDING MANAGEMENT SYSTEM (SUBHEAD-4) ₹ 0.00 ₹ 25,75,747.45 ₹ 25,75,747.45

5 Video Surveillance System(IP CCTV) (SUBHEAD-5) ₹ 0.00 ₹ 29,91,674.54 ₹ 29,91,674.54

Signature of Bidder Page No 40 of 90 DigitallySignature

signed byof ANUJ

NBCC (INDIA) LIMITED

NAME OF THE WORK :-CONSTRUCTION OF BALANCE WORKS OF MEHTA FAMILY SCHOOL OF DATA SCIENCE AND ARTIFICIAL INTELLIGENCE (MFSDSAI) INCLUDING INTERNAL EL, HVAC,

FIREFIGHTING, FIRE ALARM, LIFTS, AUDIO VISUAL SYSTEM, CCTV AND BMS INSTALLATION AND DEVELOPMENT WORKS AT I IT ROORKEE, UTTARAKHAND

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

1 1 Conference Room 28 PAX - SUBHEAD-1

1.1 1.1 Video, Video Switiching and Control

Supply, Installation, testing & Commissioning of 75" android display with SCREEN SIZE 189.3 cm

diagonal, ASPECT RATIO 16:9 3840*216, RESOLUTION (UHD), DISPLAY AREA(H x V)

1649.664(H) × 927.936(V) PIXEL PITCH 0.4296(H) × 0.4296(V), VIEWING ANGLE (HORIZONTAL /

VERTICAL) 178°(H)/178°(V)(Typ.), DISPLAY COLOURS 1.07 G, RF IN 1*Side, AV IN miniAV

1*Side, USB INPUT (2.0 SUPPORT) 2*Side（USB2.0), HDMI INPUT 3*Side, SPDIF OUT YES, RJ-45

1*Side, USB DEVICE SUPPORT USB Supported HDD, SUPPORTED FORMATS PICTURE

FORMAT: GIF/PNG/BMP/JPEG, VIDEO FORMAT: MPEG1/MPEG2/MPEG4/,

H.263/H.264/H.265/MVC/WMV/VC1/VP9/AV1, AUDIO

FORMAT:MPEG1/2/MPEG4/AC3/EAC3/AAC WMA/FLACWMA/FLAC, AUDIO OUTPUT POWER

(RMS) 10 W+10 W(Typ.) etc all complete

Supply, Installation, Testing & Commissioning of table mount flip tops with 2x universal power sockets, 6

pass through holes for HDMI, VGA, audio, LAN etc all complete

1.2 Sound Reinforcement System

Supply Installation testing and commissioning of Full digital Tabletop Delegate Discussion Unit desktop

type pure discussion unit, using a special design to ensure the machine is stable, durable, Heart-shaped

directivity capacitance pickup has double color indicating light, Speaking as red, applying as green, Unit is

1.2.1 NSI a passive device, the power is supplied by system, the input voltage is 24V With howling suppression 14.00 Nos. 49,161.75 - 6,88,264.50 6,88,264.50

function, when microphone is turned on, the native speaker automatically shut down, microphone type

capacitive diapragm, signal noise ratio (S/N) >80dB, headphone output 8-32ohm, 3.5mm miniature socket ,

power of loudspeaker 2W, unit interface 8core aerial line speacial interface etc. all complete.

Supply Installation testing and commissioning of Full digital Tabletop Cairman Discussion Unit with

Priority Chairman unit has the priority function to close all speaking unit ,Capacitive touch buttons, no

buttons pressing sound, long operating life of the buttons, waterproof design, Capacitor heart type direction

microphone, with double color indicator, Power supply; controller power supply, frequency response 20Hz-

20KHz, signal noise ratio >80dB, channel crosstalk >80dB, unit interface 8 core aviation head, maximum

power consumption 1.1W etc. all complete

Supply, Installation, testing & Commissioning of Fully Digital Conference System Controller, Frequency

response 20Hz-20KHz, Signal noise ratio >80dB, Channel crosstalk >80dB, Static power 12W, the static

power consumption <0.05% ,Circular hand-in-hand connection function, Built-in with high performance

CPU, which sets translation, discussion, attendance, voting, electronic plate as a whole, Non compressed

1.2.3 NSI audio transmission, 48K sampling rate, 20Hz~20KHz bandwidth perfect sound, system can open 8 1.00 Nos. 1,83,537.20 - 1,83,537.20 1,83,537.20

microphones at the same time , 31+1 channel cable simultaneous interpretation ,Support PC management

software, TCP/IP control, provide reliable control and safety management, individually adjust line, remote

video conferencing input, 4 audio output interface, the conference unit volume size, the adjusting range is

mute, 40dB to 0dB etc. all complete

Supply, Installation, testing & Commissioning of Ceiling Speaker - 8" / 7.5&15W,

1.2.4 NSI Power(RMS):7.5W/15W, Impedance: 8 ohms , Line Voltage: 70V/100V AC, Frequency Response: 85Hz- 8.00 Nos. 7,746.70 - 61,973.60 61,973.60

17KHz, Sensitivity(1w/1m): 91dB, Speaker unit: 8" (203mm) all complete.

Digitally signed by ANUJ

Signature of Bidder Page 41 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Supply, Installation, testing & Commissioning of mixing Amplifier-250W, Built-in MP3 player and FM

tuner and remote control, MP3 Player with USB,SD port and fluorescent screen to display the sound

number., Four function buttons: previous, play/stop, next and mode, 70V,100V and low impedance 4-16

ohms speaker output, 5 zone and all zone speaker outputs, Three Mic input by phone jack type, AUX 1-3,

Mic 1-3 volume controls and bass/treble tone control, High temp, overload and short-circuit protection etc

1.3 Cables and Connectors

Supply, Installation, testing & Commissioning of 1.5 Sqmm x 2 core(12AWG) ATC copper Conductor,

1.3.1 NSI Insulated Cores,PVC Sheathed Speaker Cables .(as per actual) 100.00 Mtrs 119.18 - 11,918.00 11,918.00

Supply, Installation, testing & Commissioning of conferencing system cables and connectors complete etc

Supply, Installation, testing & Commissioning of Shielded twisted pair CAT6 Cable (STP) complete etc as

1.3.3 NSI required. (as per actual) 20.00 Mtrs 113.12 - 2,262.40 2,262.40

Supply, Installation, testing & Commissioning of 35' High–Speed HDMI Cable with Ethernet, resolution

1.3.5 NSI Supply, Installation, testing & Commissioning of 12U air cooled rack etc all complete . 1.00 Nos 22,644.20 - 22,644.20 22,644.20

Supply, Installation, testing & Commissioning of various cables and connectors including XLR, XLR

femarle, audio, STP, euro block etc all complete

2 2 Seminar Room 90 PAX

2.1 2.1 Video System

Supply, Installation, testing & Commissioning of 3,800 or more ANSI Lumens WXGA LED Projector,

Lamp free, Mercury free, Maintenance free, 2nd generation LED Technology with 30,000 hours lifespan,

Efficient instant power on/of, bright images in any environment, 360° projection and H/V keystone for easy

installation, Comprehensive LAN control for efficient management, Native Resolution: 1280x800, DMD

Type: DC3, Brightness: 3800 (ANSI Lumens), Contrast Ratio: 3000000:1, Display Color: 1.07 Billion

Colors, Light Source Type: LED Light Source Life (hours) with Normal Mode: up to 30000, Lamp Watt:

Optical Zoom: 1.2X, Digital Zoom: 0.8-2.0x, Image Size: 30"-300", Throw Distance: 0.86-10.60m,

(100"@2.95m), Keystone: H:+/-40° , V:+/-40°, Audible Noise (Normal): 31dB, Audible Noise (Eco):

25dB, Input Lag: 16ms, Resolution Support: VGA(640 x 480) to FullHD(1920 x 1080), HDTV

Compatibility: 480i, 480p, 576i, 576p, 720p, 1080i, 1080p, Video Compatibility: NTSC, PAL, SECAM,

Horizontal Frequency: 15K-102KHz, Vertical Scan Rate: 23-120Hz alonwith 120" Diagonal 16:10 Remote

Controlled Motorised Screen, Ceiling Kit & Standard Accessories

Supply, installation, testing and commissioning of 120” diagonal motorised projection screen with remote

control etc all complete..

Supply, Installation, testing & Commissioning of digital podium with the follwoing specifications or better

highly interactive touch monitor., screen type LE, 21" to 22", resolution full HD, aspect ratio 16:9,

brightness 250 nits, computer interface: USB (1), vga (1), HDMI (2), interactive resolution 4000 LPI, tilt

screen, sliding pad for keyboard and mouse, should be non wooden podium, Keyboard and mouse shall

2.1.3 NSI also be part of the solution, podium has number of input/output ports such as HDMI In/Out, VGA In/Out, 1.00 Nos 2,34,784.60 - 2,34,784.60 2,34,784.60

should have auto switcher, Audio In/Out, USBs, Ethernet etc. mount tilt facility, should be floor mount

with wheels, should have gooseneck microphone included, should have sliding provision for keepig laptop

and using touch monitor simultaneously, should be supplied with inbuilt video switcher to automatically

switch between PC or external laptop sources etc all complete..

Digitally signed by ANUJ

Signature of Bidder Page 42 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Supply, installation, testing & commissioning of high resolution camera, integrated with a 20x optical

zoom lens, AAC Audio Encoding Support AAC audio encoding, better sound quality and smaller

bandwidth, Low-light High SNR of CMOS sensor combined with 2D and 3D noise reduction algorithm,

effectively reduce the noise, even under low illumination conditions, picture can still keep clean and clear,

USB3.0 support USB 3.0 ultra-high speed interface, can transfer uncompressed original video, and

downward compatible with USB 2.0 . USB3.0 , HDMI Network can output at the same time. It also

2.1.4 NSI support CVBS interface, 1080p Full HD Apply Panasonic's 1/2.7 inch, 2.07 million effective pixels high 1.00 Nos 1,85,920.80 - 1,85,920.80 1,85,920.80

quality HD CMOS sensor, can reach maximum 1920 x 1080 high resolution and achieve quality image,

20x optical zoom & 32x Digital Zoom, Using high quality TAMRON Lens, Local Storage support local

storage module, directly recording to local USB flash disk without NVR, Ultra-high Frame Rate the output

frame rate up to 60fps in 1080p, Remote Control Using R232 and RS485 interface, all the parameters of

the camera can be controled remotely, H.265 Support Enabling full HD 1080p video stream by ultra-low

bandwidth, bidder to submit bid specific OEM authorization etc all complete .

Supply, installation, testing & commissioning of HDMI extension over catX trasnmitter and receiver pair

upto 40 meters etc all complete.

Supply, installation, testing and commissioning of ceiling mount for PTZ camera as per ceiling design etc

Supply, installation, testing & commissioning of AV bridging device, should support resolutions up to

18Gbps (600MHz) 4K UHD with HDR (via the bypass path) while simultaneously streaming the audio and

video signal at 1080p to a USB connected PC, Shall have video timing stabilization feature helps to ensure

that the USB capture stream won’t lock up or drop, Digital stereo audio from either HDMI (LPCM 2.0) or

the 3.5mm analog audio input will be captured with the HDMI video source and should be selectable

within the capture software., HDMI input and output with HDR, 3D & 4K@60Hz support, DVI 1.0

compatible HDCP 2.2 and, HDCP 1.x compliant Supports up to 4K UHD (18Gbps, 4K@50/60Hz 4:4:4, 8-

bit) video input and output, should supports Deep Color input and output up to 12-bit Supports 10-bit and

12-bit HDR (High Dynamic Range) input/output Supports CEC bypass, Automatically scales 4K sources to

1080p for USB capture Supportsm video timing stabilization to help ensure a reliable and stable USB

capture stream, Capturing over USB 3.0 allows uncompressed video and audio data capture (1080p, LPCM

Supply, installation, testing & commissioning of server with having i7 11th gen, 16GB RAM, 1TB SSD,

Windows 10 pro, Artificial Intelligence Based Performance improvement software goes by default with

Windows OS, and 4GB graphics card, Minimum 4 PCIe slots – 2 PCIe x 1, 1 PCIe x 4 , 1 PCIe x 16,

Power 300W or higher with 92% Power Efficiency,monitor, Keyboard, Mouse should be of the same make

as OEM and have OEM logo/ trademark embossed on them (No sticker), To be supplied with monitor and

keyboard, Bidder to sumbit bid specific OEM authorization etc all complete.

Digitally signed by ANUJ

Signature of Bidder Page 43 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Supply and commissioning of video conferencing and webinar license, should enable calling with a SIP

devices, suitable licenses should be considered. All of the video and audio should be integrated into the

conference room equipment and calendar systems, Gallery feature should have AI to take a single-camera

view of multiple people in a call, and send up to three unique video streams to better display the in-room

participants to remote attendees. Remote Attendees should get an improved face-to-face experience and

interaction with call participants, it should enable start, stop and control meetings from personal mobile

devices or in-room shared controller, should support Workspace Reservation,should have Digital Signage

to display announcements and live-stream select events across the organization, Upcoming events bulletin

2.1.9 NSI board, should enable scheduling Displays, See room availability and start a meeting with one touch, shoudl 1.00 Nos 1,85,920.80 - 1,85,920.80 1,85,920.80

have Voice Command to Start a meeting without touching the controller, shoudl have centralized

Management - Dashboard to view reporting and analytics for each room available to admins, platform

should give flexibility to the users to join the meeting from PC, laptop, desktop, android and iOS devices.,

Platform must provides a complete collaboration suite for users to create adhoc meetings, schedule

meetings, chat in-meetings / outside meetings and share content in a meeting, Platform should be delivered

from cloud in a secure manner with encryption standard of AES 256 GCM, Platform should be able to

allow cloud native room devices to participate into the meeting , Platform should also allow thrid party

participants to join the meetings from cloud native room devices,

Platform should provide IM&P platform which allows point to point and group chat capability, Host should

be able to add or remove participants from the meetings, lock meetings, invite participants create breakout

rooms, manage waiting rooms , Platform should provide one-to-one and Group chat with file sharing

capabilities. , Platform should have capability for the admins / users to create chat groups / channels,

Platform should have ability to schedule meetings and re-schedule them on demand, The meetings should

be joined from cloud native room devices without need for external gateways. Minimum 200 such

participants should be able to connect to the call, should interoperate with atleast any 5 SIP or H.323

endpoint - Enable SIP or H.323 room systems to communicate with desktop, tablet, mobile devices and

other SIP or H.323 endpoints, should Support in-session webninar chat, Answer and moderate Q&A

throughout the session, Allow attendees to raise hand and respond to polls, Promote attendees to panelists

who can share audio and video, Customize webinar registration page and reminder emails, Promote social

share buttons, Build post-webinar landing page, Brand the live streaming video watermark, Gather attendee

feedback with an automatic post-webinar survey, Report on webinar attendance, Measure audience

engagement, Analyze Q&A as well as results to audience polls and surveys, Easily export all data into a csv

file, Unlimited webinar sessions for up to 30 hours each, Ability to export registrant and attendee lists,

Integrate with CRM and marketing automation tools, Monetize your webinar through paid registration,

Ability to live stream your webinar to third-party platforms, Record your webinar to the cloud, Access to

post-session reporting, Upto 500 participants, license should be for 1 year from date of handover, bidder to

submit bid specific OEM authorization

2.2 Sound Reinforcement System

Supply, Installation, testing & Commissioning of 30Watt wall speaker, Impedance: 8 Ohms, Woofer:

2.2.1 NSI 5.25"(131mm), Tweeter: 0.5" (13mm) Mylar Dome, Sensitivity: 86+-2dB/M/W, Frequency: 70Hz-18KHz(- 12.00 Nos 10,368.66 - 1,24,423.92 1,24,423.92

10dB), Power(RMS): 30Wetc all complete.

Supply, Installation, testing & Commissioning of mixing Amplifier-250W, Built-in MP3 player and FM

tuner and remote control, MP3 Player with USB,SD port and fluorescent screen to display the sound

number., Four function buttons: previous, play/stop, next and mode, 70V,100V and low impedance 4-16

ohms speaker output, 5 zone and all zone speaker outputs, Three Mic input by phone jack type, AUX 1-3,

Mic 1-3 volume controls and bass/treble tone control, High temp, overload and short-circuit protection etc

Digitally signed by ANUJ

Signature of Bidder Page 44 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Supply, Installation, testing & Commissioning of dual microphone system with Receiver: Dual Channel

2.2.3 NSI Non-Diversity, Frequency Response, 50Hz-16KHz, Polar Pattern (Hand mic) Cardioid, Output, Individual 1.00 Nos 27,888.12 - 27,888.12 27,888.12

Channel: XLR, Mix out: ¼" Jack, Power Req. (Hand mic), 2 x 1.5V AA etc all complete.

2.2.4 NSI Supply, Installation, testing & Commissioning of wireless lapel microphone etc all complete. 1.00 Nos 17,877.00 - 17,877.00 17,877.00

Supply, installation, testing & commissioning of 6 input and 4 output digital mixer with automatic echo

cancellation, USB audio output etc all complete.

2.3 Cables and Connectors.

Supply, Installation, testing & Commissioning of 1.5 Sqmm x 2 core(12AWG) ATC copper Conductor,

Insulated Cores,PVC Sheathed Speaker Cables .(as per actual)

Supply, Installation, testing & Commissioning of 22 AWG 2 core ATC Copper Conductor,PVC Insulated,

2.3.2 NSI 90% ATC Copper Braid Shielded, PVC Sheathed Microphone Cable complete etc as required. (as per 20.00 Mtrs 107.06 - 2,141.20 2,141.20

Supply, Installation, testing & Commissioning of Shielded twisted pair CAT6 Cable (STP) complete etc as

required. (as per actual)

Supply, Installation, testing & Commissioning of 35' High–Speed HDMI Cable with Ethernet, resolution

support 4K@60Hz (4:2:0)

Supply, Installation, testing & Commissioning of 3' High–Speed HDMI Cable with Ethernet, resolution

support 4K@60Hz (4:2:0)

Supply, Installation, testing & Commissioning of various cables and connectors including XLR, XLR

femarle, audio, STP, euro block etc all complete

2.3.7 NSI Supply, Installation, testing & Commissioning of 9U air cooled rack etc all complete . 1.00 Nos 17,877.00 - 17,877.00 17,877.00

3 3 Conference Room 16 PAX

3.1 3.1 Vedio System

Supply, Installation, testing & Commissioning of 55" android display with SCREEN SIZE 139 cm

diagonal, ASPECT RATIO 16:9, RESOLUTION UHD(3840*2160), DISPLAY AREA(H x V) 120.96

(H)*68.04 (V) cm, PIXEL PITCH 0.0105 (H)*0.0315 (V) cm, DISPLAY COLOURS 1.07 Billion,

VIEWING ANGLE (HORIZONTAL / VERTICAL) 178 °/178 ° (H/V), RF IN 1*Side, DTV IN 1*Side, AV

IN 1mini *Side, USB INPUT (2.0 SUPPORT), 2*Side(USB2.0), HDMI INPUT 3*Side(HDMI 2.0),

HEADPHONE OUT 1*Side, SPDIF OUT YES,optical, RJ-45 1*Side, USB DEVICE SUPPORT USB

Supported HDD, SUPPORTED FORMATS PICTURE FORMAT:, PNG/BMP/JPEG, VIDEO

FORMAT: H.265 / H.264 / H.263 / MPEG1 / MPEG2 /MPEG4, AUDIO FORMAT: MPEG1 / 2 / MPEG4

/ AC3 / EAC3 / AAC / MP3/WMA/FLAC, HOTEL MODE Yes, Basic, CEC Yes, Basic, SOUND

OUT(ARC) Yes, DOLBY AUDIO/DOLBY MS12 Yes, HDR10/HDR10+/HLG Yes. BLUETOOTH Yes

(Ver. 4) etc all complete

Supply, Installation, Testing & Commissioning of table mount flip tops with 2x universal power sockets, 6

3.1.2 NSI pass through holes for HDMI, VGA, audio, LAN etc all complete 1.00 Nos 22,525.02 - 22,525.02 22,525.02

3.2 Cables and Connections

Supply, Installation, testing & Commissioning of 35' High–Speed HDMI Cable with Ethernet, resolution

support 4K@60Hz (4:2:0) .

4 4 BUILDING MANAGEMENT SYSTEM

4.1 4.1 WORKSTATION

Supply, installation, testing and commissioning of core i7 processor, Memory of 32 GB, Hard disk size (2x

800 GB Professional/Enterprise SSD with SATA or SAS), Giga speed Network card with 2 GB Graphic

card of Resolution 2.560 x 1600 with Onboard Intel 4600 HD Windows 8.1, 64 bit Edition or Windows

Server 2008 R2 and original anti virus software.

4.1.2 NSI Laserjet A4 Black and White printer 1.00 Nos 11,821.04 - 11,821.04 11,821.04

Digitally signed by ANUJ

Signature of Bidder Page 45 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Supply, installation, testing and commissioning of Layer 2 unmanaged switch with 16/24 ports (RJ-45) port

rack mountable, SMPS power supply. The switch to switch distance shall not exceed beyond 80 meters.

4.2 4.2 APPLICATION SOFTWARE

SITC of the following window based graphical software for IBMS system with 1No Client for Operator

workstation. The Software shall have 3D & HD vector dynamic graphics with Autocad import of plan with

Zoom In & Zoom Out facility, Native 64 Bit System , Multi-Monitor Support-( Max 4 Nos) , Multi-

language support , BTL ,UL , EN Certified System, BACnet Profile B-AWS (Advanced workstation) as per

the BTL Listing, dot net platform, Certified OPC DA Server by OPC Foundation, Web-Based Server

software shall permit use of Standard Web-Browsers such as Microsoft Internet Explorer, Netscape

Navigator, etc. The Software shall comply to international standards and strive to deliver products that

4.2.1 NSI meet security standards such as ISA/IEC 62443, UL2900, ISO/IEC 27001, ISO/IEC62443 and OWASP. 1.00 Nos 2,79,938.67 - 2,79,938.67 2,79,938.67

Cybersecurity audit trail , 4-eye principle , Seamless integration of certificates within customer IT

infrastructure, Microsoft’s active directory-based authentication, Use of network infrastructure that

supports physical network or VLAN segmentation, Placing the web server in a “demilitarized zone”

(DMZ), End-to-end encryption, from client to server, End-to-end encryption between servers, Certificate-

based data exchange, Encrypted backups. The software shall have the capability to integrate with Lighting.

The software license shall have 5000 points.

Supply, installation, testing and commissioning of High-quality CAPACTIVE touch 7.0'' panels for

technical on-site operation of plants as well as room operation. The Touch Panel shall have integrated web

4.2.2 NSI server and a BACnet/ IP web interface to connect a HTML5 browser to a device on the network. Generic 1.00 Nos 65,444.97 - 65,444.97 65,444.97

operation and monitoring of plant functions (alarms, schedulers, calendars, set point changes, display of

actual values, etc.)

Supply, installation, testing and commissioning of True IP Based DDC Standalone 32 Bit Intelligent,

inbuilt web browser, peer to peer communication, interoperable DDC as per the specification. The compact

controller shall have inbuilt 2-port Ethernet switch, WLAN interface and Cloud Connectivity. The

controller shall have min 12 inputs/outputs inbuilt and can be expandable upto max 40 points by

Input/Output Modules. The DDC shall have 300 Mhz processor with 128 MByte SDRAM (DDR3) and

512 MByte NAND Flash. The controller shall be freely programmable and have System functions

(alarming, scheduling, trending, access protection with individually definable user profiles and categories).

It should have one integration port inbuilt and port for POT for local interface.

The above shall be housed in vandal proof, lockable & secure MS Cabinets to be supplied along with all

necessary switchgear protections as required. Number of controllers shall have spare capacity of 15% for

future expansion.

4.2.3.1 NSI Controller for Common Area 1.00 Set 58,592.12 - 58,592.12 58,592.12

4.2.3.2 NSI Controller for AHU (2 AHU per DDC) 4.00 Set 58,592.12 - 2,34,368.48 2,34,368.48

4.2.3.3 NSI Controller for HRU (2 HRU per DDC) 1.00 Set 58,592.12 - 58,592.12 58,592.12

4.2.3.4 NSI Controller for Axial type Exhaust Fans ( Max 4 Fans per DDC) 4.00 Set 58,592.12 - 2,34,368.48 2,34,368.48

4.2.3.5 NSI Controller for Electrical System LT/HT/Transformer/DG 1.00 Set 2,64,451.33 - 2,64,451.33 2,64,451.33

4.2.3.6 NSI Controller for Lifts (2 Lifts in 1 DDC) 2.00 Set 58,592.12 - 1,17,184.24 1,17,184.24

4.2.3.7 NSI Controller for Fire Fighting system & fire suppression System 1.00 Set 58,592.12 - 58,592.12 58,592.12

Supply, installation, testing and commissioning of True IP Based BTL & UL Listed for third party

integration. The controller shall have 2-port Ethernet switch, WLAN interface and Cloud Connectivity. It

should have BTL label (BACnet communications passed the BTL test) and consisting of Dual

microprocessor with Storage capacity of 1 GByte RAM. It should support Real Time clock upto 7 Days. It

should Support of the major communication protocols: BACnet/IP, BACnet MS/TP, Modbus IP and

Modbus RTU upto 500 points. (Note - Integrator shall be of same DDC make only.)

Integration of VRV on BACnet/IP

Digitally signed by ANUJ

Signature of Bidder Page 46 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Integration of AHU VFD on Modbus over RS485

Integration of UPS on Modbus over RS485

Integration of DG Sets on Modbus over RS485 - 4 Nos

Integration of HT Power Meter on Modbus over RS485

Integration of FAS System on BACnet/IP

4.3 FIELD INSTRUMENTS

Supplying, installing, testing and commissioning of the following sensors / transducers / transmitters.

4.3.1 NSI Combined Ambient air temperature + humidity, CO2 sensors with Display. 1.00 Nos. 26,594.31 - 26,594.31 26,594.31

4.3.2 NSI Combined PM2.5, PM10 Sensor with Display 1.00 Nos. 17,741.66 - 17,741.66 17,741.66

4.3.3 NSI Differential pressure switch Air 16.00 Nos 2,912.84 - 46,605.44 46,605.44

4.3.4 NSI Temprature sensor 1.00 Nos 1,774.57 - 1,774.57 1,774.57

4.3.6 NSI Duct static Pressure sensor 9.00 Nos 10,676.71 - 96,090.39 96,090.39

4.3.9 NSI Flameproof Level Switch 1.00 Nos 18,427.45 - 18,427.45 18,427.45

4.4 Cabling and Conduiting

Supply and laying of 2 Core 1.0 Sqmm Annealed Tinned Copper, Twisted pair, Shielded unarmoured cable

for signal and power as per specifications

3 Core 1.5 Sqmm Annealed Tinned Copper, Twisted pair , Shielded armoured cable for signal and power

as per specifications

4.4.3 NSI Supply and laying of Cat-6 unarmoured cable with required jacks and points 1200.00 Rmt 35.35 - 42,420.00 42,420.00

4.4.4 NSI HOT DIP GALVANISED GALVANISED PERFORATED TYPE CABLE TRAY - - -

5 5 Video Surveillance System(IP CCTV)

Supplying, installation, testing and commissioning of 2 megapixels resolution Network Dome Camera for

true HD quality images,2.8 – 12 mm motorized lens varifocal lens, Quad video streaming, SD card support

upto 256 GB, True Day/Night (TDN) functionality for true color image ,Motion Detection 4 Zones, Multi- Level

Sensitivity Privacy Zones 4 Zones ( 8 Zones), Snapshoot Support JPEG format Password Protection Support

Character Display Support (Channel /Date), IR Illumination20-30M IR( 30 Mtrs illuminators for clear images in

low light conditions Wide Dynamic Range 3D noise reduction for sharper images and lower bandwidth use in

low light ONVIF compliant complete in all respect with NDAA compliant, MTBF upto 1,00,000 Hours@40

degree (Support Document should be provided) with complete accessories as required as per specifications

Digitally signed by ANUJ

Signature of Bidder Page 47 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Supply, installation, testing and commissioning of 2 megapixels resolution Network Bullet camera with

Quad video streaming, Imager 1/2.8”SONY 2.43 mega low illumination CMOS,Video Compression

H.264/MJPEG,Day/Night, Mechanical ICR, Minimum Illumination-0Lux/F1.4(IR ON), IR Illumination-40-50M/30

Mtrs, Electronic Shutter-Auto/Manual(1/25~1/10000), SD card support up 256 GB, Lens 2.8 – 12 mm

Motorized varifocal lens, Resolution Main stream :D1/Q1080P(960*540)/HD720P/ HD1080P 1-25/30fps, Digital

5.1.2 NSI Noise Reduction-3D, Wide Dynamic Range-Digital WDR Motion Detection -4 Zones, Multi level Sensitivity, 22.00 Each 31,248.39 - 6,87,464.58 6,87,464.58

Privacy Zones-4 Zones/8 Zones, Snapshoot-Support JPEG format, Password Protection-Support, Character

Display-Support (Channel /Date). Regulatory Emissions-FCC Part 15 CE: EN55022, Immunity -CE: EN50130-

4, IP Rating- IP66/IP67 & IK10 rated enclosure to protect against dust and water damage ONVIF compliant

with NDAA compliant, MTBF upto 1,00,000 Hours@40 degree (Support Document should be provided) with

complete accessories as required as per specifications

Supplying of 4U Rack mount single chassis Network Video Recorder with dual Gb NIC + HDMI + 1 Display

Port, max 2 simultaneous monitors, RS-232/485 serial port, DVD, Server Operating System - Windows 10 /

Ubuntu Linux 16.04, Gen 4 Intel Core i7, Local Client Display Rate (FPS) Windows – 700 FPS (HD) Linux –

900 FPS (HD), High Performance, High Reliability IP Recorder — Continuously records 400Mbps

(Windows) & 800 Mbps (Linux) of video while hosting a local client, multiple remote clients and the web server

on a single server,RAM-8 GB, 16 GB (Optional)solid-state operating system drive, 6 x USB 2.0, 2x USB 3.0

5.1.3 NSI high air flow cooling and hardware monitoring features ensure maximum uptime. keyboard and mouse, 1.00 Each 3,60,733.62 - 3,60,733.62 3,60,733.62

Professional Grade client and server software pre-installed and software updates. Access live and recorded

video on multiple client PCs with free Windows, Mac or Linux client application. web server application is pre-

installed on the server to access video through a web browser or free Mobile iPhone / iPad and Android apps.

Maximum Storage Capacity 240TB RAID 1/5/10 or 6, Maximum Hard Drive 20 Slot (Up to 12TB) Support Up

to 64 IP Camera with NDAA compliant , with Failover Support(Optional), Dual Redundant Power Supply with

complete accessories as required as per specifications

5.1.4 NSI Supply, installation, testing and commissioning of Enterprise Class 6TB HDD. 10.00 Each 26,561.99 - 2,65,619.90 2,65,619.90

Supply, installation, testing and commissioning of Video Management System (VMS) software shall be

used to view live and recorded video from capture cards and IP devices connected to local and wide area

networks. The VMS software shall have a client/server-based architecture that can be configured as a

standalone VMS system with the client software running on the server hardware and/or the client running on

any network-connected TCP/IP workstation. Multiple client workstations shall be capable of simultaneously

5.1.5 NSI viewing live and/or recorded video from one or more servers. Multiple servers shall also be able to 55.00 Each 6,446.83 - 3,54,575.65 3,54,575.65

simultaneously provide live and/or recorded video to one or more workstations. The VMS server software shall

also have the ability to be installed on an IP edge device—such as an IP camera or encoder that allows for 3rd

party applications—allowing the device to serve as both a server and IP video recording device.The VMS shall

not charge for the number of concurrent clients (min. 50 thick clients and 16 mobile clients to be provided

along with VMS). with complete accessories as required as per specifications

Supply, Installation, Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7-3770 Processor

(8M Cache, up to 3.90 GHz); RAM: 8GB Non-ECC DDR3 1600MHz SDRAM Memory; Keyboard: 12 function

5.1.6 NSI keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; 20" TFT Monitor; Dual Graphics 2.00 Each 99,571.86 - 1,99,143.72 1,99,143.72

Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk:

250GB, 7200 RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 10 Professional 64 Bit.

Digitally signed by ANUJ

Signature of Bidder Page 48 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Supplying, Installation,Testing & Commissioning of 55 " LED Full HD TV Resolution 1920 x 1080

,Contrast Ratio (Typical) 4000:1,Built-in Speaker (10W + 10W), Magic Clone (to USB), Auto Source

Switching & Recovery, Lamp Error Detection, Super Clear Coating, Temperature Sensor, Plug and Play

(DDC2B), Pivot Display, Clock Battery, PIP/PBP, Video Wall (10x10), Image Rotation, Button Lock,

HDCP Support, Smart Scheduling, Smart F/W update, Built-In MagicInfo Premium-Swith Mounting

Brackets as per Technical Specification complete in all respect.

6 6 ELECTRICAL WORKS

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate,

suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core

cable etc. as required. Group-C

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without

independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in

surface/ recessed steel onduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper

conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in

6.3 1.5 surface/ recessed steel conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core 9200.00 Metre 267.65 24,62,380.00 - 24,62,380.00

cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated

copper conductor, single core cable in surface/ recessed steel conduit as required

6.4.3 1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 265.63 - - -

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the

existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess,

6.6 1.31 including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, 560.00 Each 405.01 2,26,805.60 - 2,26,805.60

connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess,

6.7 1.32 including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular 330.00 Each 499.95 1,64,983.50 - 1,64,983.50

switch, connection etc. as required.

1.24.4 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess,

6.8 +1.24.3 + including providing and fixing 2 Nos. 3 pin 5/6 amps modular socket outlet and 1 No. 16 amps modular 185.00 Each 693.87 1,28,365.95 - 1,28,365.95

1.27.4 switch, connection etc. as required. ( UPS Points ).

Supplying and fixing 32 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed

plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with

chained metal cover for the socket out let and complete with connections, testing and commissioning etc.

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including

1.2 painting in case of surface conduit, or cutting the wall and making good the same in case of recessed

conduit as required. (For ckt wiring extra)

Digitally signed by ANUJ

Signature of Bidder Page 49 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Note;- Only Conduit for DATA,Wiring and Data Outlet in the scope of IIT Roorkee

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular

switches in recess etc as required.

Supplying and fixing modular type call bell/ buzzer with LED indication, suitable for single phase, 230

volts, complete as required.

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including

1.2 painting in case of surface conduit, or cutting the wall and making good the same in case of recessed

conduit as required. (For Data wiring)

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution

2.4 board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB

distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus

bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as

required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.

Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar,

neutral bus bar, earth bar, din bar, interconnections, powder painted including

earthing etc. as required.(But without MCB/RCCB/Isolator)

Supplying and fixing following rating, four pole, 415 V, MCB in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current

circuit breaker (RCCB), having a sensitivity current 100mA in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable

2.1 for inductive load of following poles in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

6.35 2.11 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. 25.00 Nos. 8.08 202.00 - 202.00

Supply, assembly and laying of under floor trunking made out of 1.6mm thick GI sheet complete with

jointing sleeve, horizontal bends, floor junction box, vertical bends, level adjustment components and

closer, vertical elbow, covers, access outlet. etc. complete with all other accessories under floor installation

including cutting and chasing the floor/ or on surface, making good the same, placing in position and

cleaning from inside complete etc. as required.

Digitally signed by ANUJ

Signature of Bidder Page 50 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Supply Installation, testing and commissioning of following fittings/ luminaires/ ceiling fans complete with

necessary starter/s & copper wound/ electronic ballasts, capacitors, lamps, louvers & all other accessories,

down rods of suitable length, connections with 1.5 sq.mm. PVC insulated FRLS, copper conductor, single

core cable including loop earthing with 1.5 sq mm FRLS PVC insulated copper conductor, single core

cable etc. complete as required.

SITC of surface mounted batten, 1200mm (apprx.), IP65 dust and waterproof LED minimum 4100lm,

equivalent to Make: Philips(Signify) model : WT150C LED40S-6500 PSU L120

SITC of Suspended / Recessed pure Slim LED 4 ft stand alone Light Fittng with minimum Lumen 2500

equivalent to make: Phillips (Signify) and Cat No. RC810B LED30S 4000 PSU W10L120 OD WH

SITC of LED Recessed Downlighter with spring clips and minimum lumen 1500 lumens equivalent to

Make: Philips (Signify) model Green Perform Sleek & Cat No. DN296B LED15S-6500 PSU WH

Supply of LED indoor surface Downlighter with minimum lumen output of 1500 lumens equivalent to

make: philips (Signify) model Sleek Surface SM251C LED20S- 6500 PSU WH

Supply of LED panel housing recessed Light Fitting with minimum lumen output of 3500 lumens

6.49 NSI equivalent to Make: Phillips (Signify) Full Glow G6, Cat. No.: RC380B LED36S-6500 G6 L60W60 PSU 301.00 Nos. 4,983.34 - 14,99,985.34 14,99,985.34

SITC of Surface mounted 600mm (apprx.) LED Light Fixture minimum System Lumen Output- 1200 lm

equivalent to Philips (Signify) Cat. No. Signify BN021C LED12S 6500 PSU G

SITC of LED Bulkhead Light housing: vandal resistant, self extinguishing, UV-stabilised anti yellowing

6.51 NSI polycarbonate. Diffuser: vandal resistant, Minimum System Lumen - 735lm, equivalent to Make: Phillips 18.00 Nos. 1,037.27 - 18,670.86 18,670.86

(Signify) Cat. No. WT 140W LED7S NW PSU S1 PC

SITC of Hanging LED Fixture made of die cat alluminium with clear polycarbonate diffuser alongwith

6.52 NSI suitable suspension kit, equivalent to Make: Phillips (Signify) Cat. No. SP 321 LED20S-5700 PSU NB 6.00 Nos. 6,229.68 - 37,378.08 37,378.08

SITC of Spot Light Housing: in die-cast aluminium; Minimum system wattage 27W, Minimum System

Lumen 2100lm, equivalent to Make: Phillips (Signify) Cat. No. Uniflood C Small (27-36W)

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all

6.54 1.41 types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 50.00 Nos. 169.68 8,484.00 - 8,484.00

1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required

Supply, Installation, Testing and Commissioning of 900-1200 mm sweep, BEE 5 star rated, ceiling fan

with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod,

6.55 NSI 2 nos. canopies, shackle kit, safety rope, copper winding, and all remaining accessories including safety 196.00 Nos. 3,933.95 - 7,71,054.20 7,71,054.20

pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega

ohm,suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supply, Installation, Testing and Commissioning of 1400 mm sweep, BEE 5 star rated, ceiling fan with

Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2

6.56 NSI nos. canopies, shackle kit, safety rope, copper winding, and all remaining accessories including safety pin, 5.00 Nos. 4,176.35 - 20,881.75 20,881.75

nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega

ohm,suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch

box including connections but excluding modular plate etc. as required

6.57.1 NSI SITC of wall mounting fan 400 mm sweep revolving type with speed regulator 5.00 Each 2,714.88 - 13,574.40 13,574.40

External Lighting -

Digitally signed by ANUJ

Signature of Bidder Page 51 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

SITC of LED Post Top diecast alluminuim housing, polycarbonate diffuser, impact resistnce and fixture

6.59 NSI protection level IP65/IK10 equivalent to Make: Phillips, Cat No. BGP 161 LED 2500/NW PSU 220-240V 6.00 Nos 20,764.59 - 1,24,587.54 1,24,587.54

SITC of 3.0-4.0 mtr Decorative street GI lighting pole of the following standard shall be used on work

Design& Construction: Decorative steel tubular GI, Pole should be hot dipped galvanised, Pole should be

PU painted (marine grade) with 4 nos of foundation nut & bolt (20mm dia & 600 mm long with templates)

with a base plate of 250mmx250mm, Base Plate thickness- 15 mm. GI Pole Thickness- 3.0mm. Pole shall

have GI coating thickness of 60 micron and paint coating thickness of 90 microns. Pole OD shall be 114

mm dia with inbuilt junction box up to 6.0mtr mtr. Pole shall have a din rail for MCB mounting provision

with Bakelite sheet and 32 mm Electrical Connector with foam sheet Packing. Pole sample and drawings to

be submitted before procurement and pole design shall be approved by EIC.

SITC of LED Bollard Light diecast alluminuim housing, polycarbonate diffuser, impact resistance and

6.61 NSI fixture protection level IP65/IK10 equivalent to Make: Phillips, Cat No. BCP 151 LED 150/NW PSU 220- 6.00 Nos 12,458.35 - 74,750.10 74,750.10

SITC of LED Inground uplighter compact and robust design with diecast alluminuim housing and stainless

6.62 NSI trim, IP68 waterproof connectors equivalent to Make: Phillips Cat No. BBP 341 LED 540/WW 6W 20D 6.00 Nos 7,475.01 - 44,850.06 44,850.06

SITC of Surface Mounted Linear Wallwasher Housing extruded aluminium housing, IP66 / IK06

protection equivalent to Make: Phillips Cat No. UniStrip G4 AC BCP384 20-80W

SITC of LED Inground Linelite compact and robust design with extruded alluminium housing, IP68

6.64 NSI waterproof connectors equivalent to Make: Phillips Cat No. Signify Cat No. BBP412 LED RGB 36W 24V 4.00 Nos. 18,168.89 - 72,675.56 72,675.56

SITC of Architecrural Spot Light Housing: in die-cast aluminium; Minimum system wattage 27W,

6.65 NSI Minimum System Lumen 2100lm, equivalent to Make: Phillips (Signify) Cat. No. Uniflood C Small (27- 12.00 Nos. 45,473.23 - 5,45,678.76 5,45,678.76

SITC of LED step light compact and robust design with diecast alluminuim housing and stainless trim,

frosted glass didffuser, IP67/IK08 waterproof connectors equivalent to Make: Phillips, cat no. BWG150

LED50/WW PSU 220-240V IP67 7043

SITC of LED spike light compact and robust design with diecast alluminuim housing and stainless trim,

6.67 NSI frosted glass didffuser, IP65/IK08 waterproof connectors equivalent to Signify Cat. No. BGP150 8.00 Nos. 4,879.31 - 39,034.48 39,034.48

LED580/WW 8W 20D GM

SITC of LED Inground uplighter compact and robust design with diecast alluminuim housing and stainless

6.68 NSI trim, IP68 waterproof connectors equivalent toSignify Cat. No. BBP 344 LED 3600/WW 36W 20D 100- 5.00 Nos. 15,054.05 - 75,270.25 75,270.25

SITC of Updownlighter Housing in die-cast aluminium IP65/IK08 waterproof equivalent to Philips

Decorative Lighting Cat. No. 31450

Supplying and drawing following sizes of PVC insulated PVC sheathed copper conductor unarmoured

multicore cable in the existing poles and bracket from cable termination connector to the fitting i/c

providing suitable copper lugs connections etc. complete in all respect as required.

Supply & laying of following size of 1.1KV grade multicore aluminium conductor XLPE insulated and

PVC sheathed armoured cable in existing trenches/ Hume pipe/in ground as per IS : 7098:1988 with upto

date amendments complete in all respect as required.

Supplying and making end termination with brass compression gland and copper lugs for following size of

PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Digitally signed by ANUJ

Signature of Bidder Page 52 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Providing, laying and fixing following dia RCC pipe NP 2 class (light duty) in ground complete with RCC

14.14 collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and

refilling etc. as required.

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings

SITC of following items for lightning protection AS PER IEC 62305 / IS IEC 62305

Air Termination Network:

SITC of single spike air terminals of 10 mm dia. & 1000 mm length as required and as per site conditions.

6.77 NSI The air terminal shall be manufactured with aluminium & shall be as per IEC 62561-2. The air terminal 5.00 Nos. 1,748.31 - 8,741.55 8,741.55

shall be fixed with necesarry clamping arrangement.

SITC of Roof Conductor for Parapet & Mesh : Supply of 8 mm dia aluminium round conductor for air

6.78 NSI termination network at parapet and for making mesh at terrace level and shall meet the requirement of IEC 386.00 RM 113.12 - 43,664.32 43,664.32

SITC of Parapet Conductor holder for holding of 8 mm dia. round conductor (for RCC roof). The

6.79 NSI conductor holder shall be mounted on plastic base support and shall meet the requirements of IEC 62561- 341.00 Nos. 169.68 - 57,860.88 57,860.88

4.It should be installed at every 1 mtr

SITC of Mesh Conductor holder for holding of 8 mm dia. round conductor (for RCC roof). The conductor

6.80 NSI holder shall be fixed on plastic support weighed by concrete block. It shall meet the requirements of IEC 45.00 Nos. 169.68 - 7,635.60 7,635.60

62561-4 and should be installed at every 1 mtr.

SITC of Bridging cable: Supply of 16sq.mm. copper cable along with lugs, having 500mm length & as per

IEC 62561-1 so as to connect air termination rod with any metallic structure on the roof

SITC of Straight - Connector for making straight joint of 8 mm Aluminium Conductor to 8 mm dia

Aluminium conductor on parapet wall, roof and vertical facade of masonery / glass / metallic work.

SITC of T - Connector for making Tee joint of 8 mm dia. Aluminium Conductor to 8 mm dia Aluminium

conductor on parapet wall, roof and vertical facade of masonery / glass / metalic work

DOWN CONDUCTOR AS PER IEC 62305

SITC of 8 mm dia aluminium round conductor for Down conductors to be installed on vertical wall, façade

of masonary / glass / metalic work. It shall meet the requirements of IEC 62561-2.

SITC of Wall Conductor holder for holding 8 mm dia. round conductor (for RCC wall). The conductor

6.85 NSI holder should be installed at every 1 mtr. The conductor holder shall be made with clamp mounted on 220.00 Nos. 169.68 - 37,329.60 37,329.60

plastic base support & as per IEC 62561-4.

SITC of Test Clamp to disconnect the down conductor from the earth termination network for regular

6.86 NSI checks of the earth termination resistance value. (with enclosure). It shall meet the requirements of IEC 7.00 Nos. 1,417.03 - 9,919.21 9,919.21

SITC of Expansion piece made of 8mm dia. Aluminium & as per IEC 62561-2 along with suitable

6.87 NSI connecting accessory. It shall be installed at every 20 mtr to maintain the flexibility to the conductor due to 20.00 Nos. 472.68 - 9,453.60 9,453.60

SITC of Lightning Strike counter Model: JMV 7D for counting the number of lightning strikes without any

6.88 NSI power supply. The Counter should be mounted on the Down Conductor. The Lightning Counter should be 1.00 Nos. 7,086.16 - 7,086.16 7,086.16

IP 65 rated enclosure suitable for external application.

Earth Termination Network:

SITC of Earthing termination made of copper-bonded rod of 10 feet length,14.2 mm dia. (Minimum

copper bonding shall be 0.25mm) as per IS 3043, IEEE-80, NBC 2016 along with Earth enhancement

material some with resistivity of 0.12 ohm-mtr, and complying IEC 62561-7 and Pit Cover complying IEC

62561-5 and other accessories as required and as per specification and other applicable codes

Digitally signed by ANUJ

Signature of Bidder Page 53 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

SITC of 8 mm CBS Conductor laid at 600mm below the ground, as Required and as per specification and

code of practice with Tee and Straight joint

Surge Protection Device:

SITC of Class B/Type I Single Phase Surge Protection Devices as per IEC 62305-4 and tested according to

IEC 61643 – 11, DIN Rail mountable with Maximum Continuous Operating Voltage of 320 V and Voltage

Protection Level of ≤ 2.5 kV. Response Time should be less than 100 ns. The maximum impulse test

current should be 50 kA (10/350 μs) per pole and 100 kA (10/350 μs) neutral to protective earth. The surge

protection devices shall be enclosed in polycarbonate enclosure of IP 65 rating

SITC of Class C/Type II Single Phase Surge Protection Devices as per IEC 62305-4 and tested according

to IEC 61643 – 11, DIN Rail mountable with Maximum Continuous Operating Voltage of 320 V and

6.92 NSI Voltage Protection Level of ≤ 1.5 kV. Response Time should be less than 25 ns. The maximum impulse 4.00 Nos. 4,723.77 - 18,895.08 18,895.08

discharge surge current should be 20 kA (8/20 μs) per pole and 40 kA (8/20 μs) neutral to protective earth.

The surge protection devices shall be enclosed in polycarbonate enclosure of IP 65 rating

MAIN LT PANEL (BUILDING MAIN PANEL)

MAIN LT PANEL & DISTRIBUTION PANEL

The rates for the distribution boards from the Breakers and instruments shall also include the following:

NOTE: The following provisions shall be required to be made in the switchboard detailed below:

The Switchboard shall have provision for entry of all PVC cables / bus duct from the top / bottom as

All live accessible parts shall be shrouded and all equipment shall be ginger touch proof. The busbar

insulation shall be with heat shrinkable sleeves SMC / DMC shrouds and busbar supports shall be used.

Suitable tinned copper extension links for incoming / outgoing cables shall be provided wherever required.

Control circuits includes breaker control switch, auto manual selector switch, anti pumping relay, spring

charging trip indication, TIMER, Control wiring, Auxiliary contactors MCB's as required at site.

All the incomers breaker shall be interlocked with micro PLC to avoid parallel operation . Stabilized

separate power supply to be provided for micro PLC hand wiring interlocking shall also be provided.

All the incomers breaker having microprocessor breaker shall have neutral CT

All fault level breaking capacity indicates shall be I.C.S. value at 415 volts. (ICS=ICU=ICW=100%) for 1

All MCCB above 250 Amp shall have variable overload and short circuit setting.

All ACB/MCCB shall have with Rotary Handles.

Space heater / light / air filter shall be provided for each vertical compartment.

Padlocking facility shall be provided on all outgoing feeders

All ACB's shall have all standard accessories such as CT,s Arc Chute, safety shutters etc.

All meter panel wiring from PLC to DG/TR/Bus coupler as required.

Link and drops from ACB / MCCB shall be designed for fall rated current of ACB / MCCB rating at same

amount of current density as of main busbar.

All panel should be on Ethernet with embedded web page to monitor ON/OFF/Trip status of the breaker.

Compliance to the technical specifications.

All MCCB in main panel should have O/L, S/C, E/F protection with S/C and E/F differtation.

Digitally signed by ANUJ

Signature of Bidder Page 54 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

All MFM shall have minimum sampling rate of 64 samples/cycle & feature of individual Harmonic

distortion upto 15th order.

MAIN LT PANEL (BUILDING MAIN PANEL)

Supplying, installation, testing & commissioning of cubical type LT panel suitable for 415V, 3 Phase,

4Wire 50 Hz AC supply system, fabricated in compartmentalized design from CRCA sheet steel of 2mm

thick for frame work and covers, 3mm thick for gland plates i/c cleaning & finishing complete with 7 tank

process for powder coating in approved shade, having 1250 Amp capacity extensible type FP Aluminium

Alloy bus bars of high conductivity, encapsulated with PVC sleeve, DMC/ SMC bus bar supports, with

short circuit withstand capacity of 50 MVA for 1 Sec., bottom base channel of MS section not less than

100mm x 50mm x 5mm thick, fabrication shall be done in transportable sections, entire panel shall have a

common copper earth bar of size 50mm x 6mm at the rear with 2 Nos. earth stud, 24V DC powerpack,

solid connections from main bus bar to switch gears with required size of Al. bus bars and control wiring

with 2.5sq.mm. PVC insulated copper conductor S/C cable, cable alleys, cable gland plates in two half, i/c

providing following switch gears:-

a) Air Circuit Breaker Horizontal drawout type LSIGUN protection and Data storage of last 20 trips and

80events.The ACB shal be of fault breaking capacity 50KA (Ics=lcu =Icw for 1 sec) upto 415V) Electrical

Draw Out Motorized operated, fitted with interlocked door, automatic safety shutters, mechanical ON/OFF

and service/ test/isolated position indicators and frame earthing contact, conforming to IS-13947-2 1993 as

amended up-to-date complete with following accessories for each ACB

b) Independent Electrical / manual spring closing mechanism - I No.

c) Microprocessor release(EMI & EMC certified) for over current, earth fault & short circuit protection -

d) calibrated Intelligent multifunction digital panel meters of class 0.5S accuracy with communication

interface port RS 485 for recording V ( Between Phases and between each phase and neutral ), A ( In each

Phase and neutral), KVA, KW, KWhr, KVAR, pf, 64 samples/cycle, Total harmonic distortion, with

suitable rating CTs etc. complete with wiring , connections etc.

e) 3 Nos. Phase indication LED lamps with 2Amp back up MCB, breaker 'ON/OFF' indicating light with

2A MCB, test terminal block set, circuits as per standard practice, auxiliary contacts for positive

interlocking of the breakers as required.

f) Shunt trip coil 220V A.C.

g) 27-Undervoltage with definite time relay - 1 No

h) 1 No. DC under voltage trip relay

1 No. 1000 A, 4P, 50 KA ( BY IIT ROORKEE )

1250A, 4P Aluminium bus bar

Following rated 415V, ACB's/MCCB's with overcurrent and short circuit releases Microprocessor based

with ON,Trip indications, front operating handle & door interlock with 1 Set of three phase R,Y,B

indicating lamps along with 2A SP MCB backup protection and control terminals & wiring as required.

etc. complete with dual source MFM in all respects as mentioned in specifications and as required For

each outgoing: ( All Outgoings of Icu=Ics= 50 KA Rating)

800 A 35 KA, 4P MCCB - 1 No.(for Essential Panel)

630 A 35 KA, 4P MCCB - 1 No.(for outdoor AC Panel + spare)

63 A 35 KA, 4P MCCB - 1 No.(for External Lighting Feeder Piller)

6.930 NSI LT Panel Described as above complete 1.00 Set 4,75,881.00 - 4,75,881.00 4,75,881.00

Digitally signed by ANUJ

Signature of Bidder Page 55 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

6.940 NSI ESSENTIAL PANEL

Supplying, installation, testing & commissioning of cubical type LT panel suitable for 415V, 3 Phase,

4Wire 50 Hz AC supply system, fabricated in compartmentalized design from CRCA sheet steel of 2mm

thick for frame work and covers, 3mm thick for gland plates i/c cleaning & finishing complete with 7 tank

process for powder coating in approved shade, having 1000 Amp capacity extensible type FP Aluminium

Alloy bus bars of high conductivity, encapsulated with PVC sleeve, DMC/ SMC bus bar supports, with

short circuit withstand capacity of 50 MVA for 1 Sec., bottom base channel of MS section not less than

100mm x 50mm x 5mm thick, fabrication shall be done in transportable sections, entire panel shall have a

common copper earth bar of size 50mm x 6mm at the rear with 2 Nos. earth stud, 24V DC powerpack,

solid connections from main bus bar to switch gears with required size of Al. bus bars and control wiring

with 2.5sq.mm. PVC insulated copper conductor S/C cable, cable alleys, cable gland plates in two half, i/c

providing following switch gears:-

1No. 630A 4P Automatic transfer switch with 630 Amps 4 Pole, 35 KA, MCCB with thermal & magnetic

releases.with 3 Nos. R,Y,B Indication Lamps with 2A back up SP MCB with ON indication.MCCB shall

be provided with spreader link and direct rotary handle.

Dual core calibrated digital Multifuctional meter of class 1.0 to record demand (KVA), energy (KWH &

KVAH), power factor, current (in each phase and the neutral), volatge (between phases and between each

phase and neutral), Total haramonic distoration (THD) as a percentage of total current,and 3 Nos. dual core

CT of 630 /5 A Class 1.0 accuracy and 30 VA burden.

Shunt trip coil 220V A.C.

Following indicating lamps and push buttons for each CB with back up 2A SP MCB .

3 No. Phase indicating Lamps .

800A, TPN Aluminium bus bar

Following rated 415V, ACB's/MCCB's with overcurrent and short circuit releases Microprocessor based

with ON,Trip indications, front operating handle & door interlock with 1 Set of three phase R,Y,B

indicating lamps along with 2A SP MCB backup protection and control terminals & wiring as required.

etc. complete with dual source MFM in all respects as mentioned in specifications and as required For

each outgoing: ( All Outgoings of Icu=Ics= 35 KA Rating)

400 A 4P 25 KA MCCB - 2 Nos.(1 No.for Power Rising Main + spare )

315 A 4P 25 KA MCCB - 1 No.(Data Center )

160 A 25 KA, 4P MCCB - 3 Nos.( Ventilation Panel + UPS I/P Panel + spare)

125 A 25 KA, 4P MCCB - 3 Nos.(1 No.for Light Rising Main + I/D AC Panel + Ventilation Panel )

63 A 25 KA, 4P MCCB - 4 Nos.(for 3 Nos. Lift + spare )

6.940 NSI Essential panel Described as above complete 1.00 Set. 5,68,643.00 - 5,68,643.00 5,68,643.00

6.950 NSI Feeder Pillar for External Lighting

Digitally signed by ANUJ

Signature of Bidder Page 56 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Supply, assembly, erection, connecting, testing & commissioning of LT weather proof dust and vermin

proof, outdoor feeder pillar, fabricated out of suitable sized angle iron and flats and covered with 3mm

thick CRCA sheet steel including canopy, duly stove enamel painted, both sides (front and rear) openable

with locking arrangement, rubber gasket cable glands, etc. Bakelite phase separators and bus bar supports

including PCC 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) foundation,

450 mm deep and 150 mm above the ground. The feeder pillars shall be complete with 3 phase and neutral

bus bars of capacities as described below and moulded case circuit breakers (MCCBs) with adjustable

overload relays for incomers and outgoing circuits ( including ON indication for each MCCB to be

provided) , complete in all respects as per specifications as required.

63A 4P MCB 10 kA - 1 No.

TPN bus bar of 100A rating

32A TPN MCB (10ka) - 4 nos.

40A TPN MCB (10ka) -1 nos.

40A, 4P Contactor - 1 No.

Astronomical Time Switch with daily dial - 1 No.

Auto Manual Selector Switch - 1 No.

63A DP MCB (10ka) - 6 nos.

6.950 NSI Feeder pilllar Described as above. 1.00 Set. 31,562.00 - 31,562.00 31,562.00

6.960 NSI DISTRIBUTION PANELS

Supplying, installation, testing & commissioning of cubical type wall mounted motor control Distribution

panel suitable for 415V, 3 Phase, 4Wire 50 Hz AC supply system fabricated in compartmentalized design

from CRCA sheet steel of 2mm thick for frame work and covers, 3 mm thick for gland plates i/c cleaning

& finishing complete with 7 tank process for powder coating in approved shade, having suitable capacity

extensible type FP Aluminium Alloy bus bars of high conductivity, DMC/ SMC bus bar supports, with

short circuit withstand capacity of 31 MV A for I Sec. with 2 Nos. earth stud, solid connections from main

bus bar to switch gears with required size of Al. bus bars and control wiring with 1.5 sq.mm. PVC

insulated FRLS copper conductor Single Core cable, cable alleys, cable gland plates in two half, i/c

additional NO/NC contacts in all outgoing starters for automatic operation through BMS and providing &

fixing following switch gears:-

1 No. - 100 Amps Four Pole, 35 KA (ICU=ICS), MCCB with adjustable thermal and adjustable magnetic

release, direct rotary handle.

Digital Multifuctional meter of class 0.5 or better accuracy to record demand (KVA), energy (KWH), Total

power factor, current (in each phase and the neutral), volatge (between phases and between each phase and

neutral), Total haramonic distoration (THD) as a percentage of total current, comprises of suitable

communication port for connection to IBMS.

TPN aluminium bus bars of minimum of 150 Amps capacity with heat shrinkable coloured sleeves and i/c

DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing

Digitally signed by ANUJ

Signature of Bidder Page 57 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

40 Amp 4P MCB '10 KA' - 4 Nos.

6.960 NSI Panel described as above 4.00 Set. 41,183.00 - 1,64,732.00 1,64,732.00

6.970 NSI POWER PANEL

1 No. -125 Amps Four Pole, 25 KA (ICU=ICS), MCCB with adjustable thermal and adjustable magnetic

release, direct rotary handle.

Digital Multifuctional meter of class 0.5 or better accuracy to record demand (KVA), energy (KWH), Total

power factor, current (in each phase and the neutral), volatge (between phases and between each phase and

neutral), Total haramonic distoration (THD) as a percentage of total current, comprises of suitable

communication port for connection to IBMS.

TPN aluminium bus bars of minimum of 150 Amps capacity with heat shrinkable coloured sleeves and i/c

DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing

63 Amp 4P MCB '10 KA' - 6 Nos.

6.970 NSI Panel described as above 4.00 Set 39,483.00 - 1,57,932.00 1,57,932.00

6.980 NSI UPS PANEL

1 No. -100 Amps Four Pole, 25 KA (ICU=ICS), MCCB with adjustable thermal and adjustable magnetic

release, direct rotary handle.

Digital Multifuctional meter of class 0.5 or better accuracy to record demand (KVA), energy (KWH), Total

power factor, current (in each phase and the neutral), volatge (between phases and between each phase and

neutral), Total haramonic distoration (THD) as a percentage of total current, comprises of suitable

communication port for connection to IBMS.

TPN aluminium bus bars of minimum of 150 Amps capacity with heat shrinkable coloured sleeves and i/c

DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing

63 Amp 4P MCB '10 KA' - 5 Nos.

6.980 NSI Panel described as above 4.00 Set 39,285.00 - 1,57,140.00 1,57,140.00

6.990 NSI UPS Panel

Supplying, installation, testing & commissioning of cubical type wall mounted motor control L T panel

suitable for 415V, 3 Phase, 4Wire 50 Hz AC supply system fabricated in compartmentalized design from

CRCA sheet steel of 2mm thick for frame work and covers, 3 mm thick for gland plates i/c cleaning &

finishing complete with 7 tank process for powder coating in approved shade, having Suitable capacity

extensible type FP Aluminium Alloy bus bars of high conductivity, DMC/ SMC bus bar supports, with

short circuit withstand capacity of 31 MV A for I Sec. with 2 Nos. earth stud, solid connections from main

bus bar to switch gears with required size of Al. bus bars and control wiring with 1.5 sq.mm. PVC

insulated FRLS copper conductor Single Core cable, cable alleys, cable gland plates in two half, i/c

additional NO/NC contacts in all outgoing starters for automatic operation through BMS and providing &

fixing following switch gears:-

Digitally signed by ANUJ

Signature of Bidder Page 58 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

UPS INPUT PANEL

1 No. - 160 Amps Four Pole, 25 KA MCCB (Icu=Ics) with micro processor based releases with 3 Nos.

R,Y,B Indication Lamps with 2A back up SP MCB with ON,Trip indication.MCCB shall be provided with

spreader link and direct rotary handle

FP CU. bus bars of minimum of 200A 35 kA capacity with heat shrinkable coloured sleeves and i/c

DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing

3 No. 100A 4P MCCB having breaking capacity 25 KA (Ics=Icu) with thermal magnetic releaase with

o/c,s/c protection release all indication,front operating handle & door interlock.

6.990 NSI panel described as above 1.00 Set 98,014.00 - 98,014.00 98,014.00

6.100 NSI UPS OUTPUT PANEL

3 Nos. - 100 Amps Four Pole, 25 KA (ICU=ICS), MCCB with adjustable thermal and adjustable magnetic

release, direct rotary handle. (necessary interlocking to be done of both incomers)

Digital Multifuctional meter of class 0.5 or better accuracy to record demand (KVA), energy (KWH), Total

power factor, current (in each phase and the neutral), volatge (between phases and between each phase and

neutral), Total haramonic distoration (THD) as a percentage of total current, comprises of suitable

communication port for connection to IBMS.

FP copper bus bars of minimum of 150 A capacity with heat shrinkable coloured sleeves and i/c

DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing

160 Amp. 4P MCCB 25KA with E/L protection- 25KA - 2 No.(UPS Rising Main + Spare)

63Amp TPN MCB '10 KA' - 4 Nos . (spare)

6.100 NSI Panel described as above 1.00 Set 1,99,675.00 - 1,99,675.00 1,99,675.00

6.101 NSI AC Panel for indoor units

Digitally signed by ANUJ

Signature of Bidder Page 59 of 90 GULIA Signature of NBCC

SCHEDULE OF QUANTITIES (ELECTRICAL WORKS)

CPWD Rate Rate Amount Amount Total Amount

CPWD Rate Rate Amount Amount Total Amount

S.No. Description of Item Quantity Unit

DSR 2018 DSR Non-DSR DSR Non-DSR DSR + Non-DSR

Supply, installation, testing and comissioning of dust, damp and vermin proof cubicle free floor, indoor

type factory built sheet steel enclosed modular bolted construction extendable Panel, suitable for operation

on 415 ±10% volts, 50 Hz AC 3 phase 4 wire supply system fabricated out of Form 3b compartmentalized

design and covered with CRCA sheet steel of 2mm thick for frame work and 1.6mm thick for doors/

covers, 3mm thick for gland plates i/c cleaning & finishing complete with 9 tank process for powder

coating in approved shade, having extensible type TPN Aluminium bus bars of high conductivity, SMC

bus bar supports, with short circuit with stand capacity of 35KA for 1 sec., bottom base channel of section

not less than ISMC 75mm, fabrication shall be done in transportable sections, entire panel shall have a

common copper earth bus bar to switch gears with required size of Alum. bus bars and inter-connection

with solid copper conductor wires/ aluminium strips, neutral links, including control wiring with 1.5sqmm.

PVC insulated FRLS copper conductor Single Core cable for voltage & 2.5sq.mm for current circuits, cable

alleys, cable gland plates in two half, danger notice plates, etc. necessary metering protections &

indications and mounted with the following switch gears as per drawing and technical specifications etc.

complete as required.

1No. 125 Amp 433V, 4P MCCB of 25 kA Breaking capacity with On Indica ting Lamp with 2A SP MCB

Metering incoming:

Each Incomer (Ics=lcu) with O/L, S/C & built-in earth fault protection