CA NO. CWE/HILLS/RKT/114 OF 2025-2026 SPECIAL REPAIR TO BLDG NO P-71 (ORs MD ACCN) AT MIL STN HALDWANI

Amount

Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B-0 (12.5mm graded stone aggregate) as in level course with finshining in cement concrete surface even and rough to receive screed bed complete all as specified and directed.

M&L 75mm thick Cement concrete type B- 2, 1:2:4 (40mm graded aggregate) complete as in level course with finishing in cement concrete surface even and rough to receive screed bed complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection incl finishing even and smooth without using extra cement complete all as specified and directed..

M&L for PCC 1:3:6 type C-1(using 20mm graded stone agg) for bed block for fixing hold fast complete all as specified and directed.

M&L for Roof tiles, Mangalore pattern, interlocking at side joints on chhajja top, laid on 15mm thick screed bed or bedding in cement mortar 1:4 complete all as specified and directed..

Demolition of cement concrete in but of any description and in any position not other wise specifically provided for complete all as specified and directed.

M&L for providing PCC 1:2:4 type B-0 as in roof kerbs or mud stops rouded or chamfered on edges (using 12.5mm graded stone aggregate) complete all as specifed and directed.

Dismantling of brick tilesor terracing tiles, single layer on roofs complete all as specified and directed.

M&L 50mm thick (laid in two equal layer of 25 mm thick) in PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) including finishing even and fair as in roof padding and prepare surface to receive treatment complete all as specified and directed.

S & F 1.4mm dia galvanised steel wire netting 20mm X 20mm mesh size , made up into matteresses or cages, lapped , wired and laid in position, including fixed with tinned tacks of wire staples complete all as specified and directed.

M&L 40 mm thick brick tiles laid over and including 15mm thick bedding layer in cement mortar 1:6 and jointed, grouted and pointed flush in cement mortar 1:3 including liquid water proofing admiture @ 200ml of per 50 kg of cement of make Sika/Pidilite/ Choksey Chemicals/Fosroc complete all as specified and directed.

M&L for APP based polymeric membrane minimum weighing 3.00Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (Wt not less than 150 gms /sqm) laid on bituminous surfaces by forced application over entire roof area, sunken portion with side lap not less 100mm and end lap not less than 150mm including apply a tack coat of industrial bitumen complete all specified and directed.

M&L for applying a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm including cleaning surfaces etc complete all as specified and directed by engr in charge.

Demolition and taking out cement mortar or lime concrete, brick bats from sunken floor portion complete all as specified and as directed.

M&L for lime conrete with lime mortar 1:5:10 mix using 40mm graded brick coarse aggregate in sunken Portion of WC/bath room complete all as specified and as directed.

M&L for 15mm thick cement plaster as in sunken portion of WC/Bath room using cement mortar (1:4) on fair faces of concrete surfaces including water proofing compound where ever required as per manufacturerer's instructions and finishing the surface even and smooth (using extra cement) etc. complete all as specified and directed. NOTE -WPC shall be measured and paid separetely.

M&L for cleaning surface of Sunken Portion of WC and applying a coat of bitumen primer @ 0.30 Kg/Sqm and thereafter applying a tack coat of industrial bitumen 85/25 grade @ 1.20 Kg/Sqm and provn of APP based polymeric membrane minimum weighing 3.00Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (Wt. not less than 150 gms/sqm) laid on bituminous surfaces by forced application over entire roof area, with side lap not less 100mm and end lap not less than 150mm complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 type B-0 as in Sunken Portion of WC/Bath room (using 12.5mm graded stone aggregate) complete all as specifed and directed.

S&F 40mm dia (Bore), spout pipe, fixed on sunken, complete as all specified and as directed.

Dismantling floor, hearth, wall tiling including taking down plastering in cement mortor removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Joint free Non - skid coloured ceramic tiles 7 to 10 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry over screed bed of 15 mm thick in cement mortar 1:6 and pointed in white or coloured cement to match complete all as specified and directed..

M&L Joint free Non - skid coloured ceramic tiles 7 to 10 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry over screed bed of 15 mm thick in cement mortar 1:6 and pointed in white or coloured cement to match complete all as specified and directed.

M&L Joint free Non - skid coloured ceramic tiles 7 to 10 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm in skirting/dado or verticle surfaces with back coat of screed bed or bedding layer of 10 mm thick in cement mortar 1:4 and pointed in white or coloured cement to match complete all as specified and directed.

M&L Glazed coloured ceramic tiles in verticle surfaces 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match with backcoat of screed bed or bedding layer 10mm thick in cement mortar 1:4 and pointed in white or coloured cement to match complete all as specified and directed.

M&L for Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade incl rounding off edges and bull noosing of all external edges over screed bed of 15 mm thick in cement mortar 1:6 and pointed in white or coloured cement to match complete all as specified and directed.

Demolition of brick work built in cement mortar complete all as specified and directed.

M&L for brick work with sub class `B’ bricks, straight on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for half brick work with sub class `B’ bricks, straight on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed..

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed..

M&L for Nominal mix RCC 1:2:4 type B-1, Slab supported on walls,beams and columns in floors,roof, landing, balconies,in type B1(20mm graded aggregate) complete all as specified and directed..

M&L for Formwork to soffits of suspended slabs such as roof slab, floor slabs landings and sgh finished surfaces of concrete flat complete all as specified and directed..

M&L precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mortar 1:4 including necessary form work complete all as specified and directed. Note :- Reinforcement shall be measured and paid separately under relevent item of this schedule.

M&L for providing Precast cement concrete type B0 1:2:4 (12.5mm graded aggregate) set in cement mortar 1:4 in louvers and jallies, 40mm thick (measured solid), including all mouldings and interlocking pillars complete all as specified and directed.

M & L for mild steel TMT bars,10mm dia and over, cut to length, bent to shspe required incl cranking , bending spirally for hooping for coloumns, hooking ends andbionding with (annealed) not less than 0.90 mm dia complete all as specified and directed.

S&F in repair 18/19mm thick Prelaminated board, interior grade, prelaminated both side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

M&L for stainless steel telescopic channel for drawers not less than 45 cm long complete all as specified and directed. Make Hettich or equivalent in godrej/ebco/kich

S&F Push to open Magnetic Catches for kitchen cabinet doors complete all as specified. Make Hettich or equivalent in godrej/ebco/kich as approved by Engr-in-charge

S&F Stainless sensys soft close 0 crank concealed slide on cabinet Hinge, a base of 12.5 (crank 0 degree) with mounting plate (shutter thickness 15-24mm) complete all as specified and directed. Make Hettich or equivalent in godrej/ebco/kich

S&F Contnuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps (when open) 30mm complete all as specified and directed. Make Hettich or equivalent in godrej/ebco/kich

S&F Stainless Steel Decorative Cabinet Handle 100 mm complete all as specified and directed. Make Hettich or equivalent in godrej/ebco/kich

S & F hasp and staple 150mm size of aluminium anodised complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10cm girth complete all as specified and directed..

Taking up or down GI Water Tubing 15mm dia (bore) including Connections and Fittings, complete all as specified and as directed.

All as per Item No. 44 here–in–before, but for 20mm dia (Bore).

All as per Item No. 44 here–in–before, but for 25mm dia (Bore).

Supply and Laying Steel Water Tubing 15mm dia (Bore), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, complete as all specified and as directed.

All as per Item No. 47 here–in–before, but for 20mm dia (Bore).

All as per Item No. 47 here–in–before, but for 25mm dia (Bore).

S&F in repair 15mm dia bib taps CP Brass with Capstanhead, screwed down, screwed for iron pipe of bore 15mm complete all as specified and directed.

S&F in repair Angle Cock,15mm fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repair Brass chromium plated shower rose 125mm size with 225 mm Flange, swivel joints, including fixing to steel pipe or union complete all as specified and directed.

S&F in repair Tubular towel Rail CP Brass, chromium plated D type with CP Brackets, 600 mm long between flanges complete all as specified and directed.

S&F in repair Soap Dish Stainless Steel complete all as specified & directed.

S&F in repair Peg Set of 6 Stainless Steel as approved by Engr-in-Charge

S & F in repair Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete all as specified and directed.

S&F in repair brass Chromium plated Basin Mixer/ Sink Mixer valve hot and cold screwed down for iron pipe of size 15mm bore complete all as specified and directed.

S&F in repair Brass CP Wall mixer for mixing hot & cold water (3 in 1) screwed down for iron pipe and fixed bore of pipe 15mm complete all as specified and directed.

S&F in repair Corner Glass Shelf 300mm (with ABS Brackets) 300 x 600mm as approved by Engr-in-Charge

S&F in repair 25mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Dismantling water tanks of capacity exc 250 but not exc 500 ltr capacity complete all as specified and directed.

S&F rotational moulded polythene water storage tanks tripple layer (cylindrical vertical with closed top) hoisted and fixed in postion 500 ltrs capacity with and including 25mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe minimum weight 210 gram complete all as specified and directed.

S&F in repair stainless steel plate rack of stain less steel 1.00 mm thick of size size 24" x 30" x 10" (inch) of best quality including necessary stain less steel screws, rawl plugs and washerscomplete all as specified and directed.

S&F in repair vitreous China squatting pan, Orissa pattern including CI spun trap, size 580 x 440 mm white, with integral foot rests squat pattern closet also includes setting the trap and pan in lime concrete (1 lime, 2 sand or surkhi and 5 aggretate), min. 150mm thick all round and finished just below level of rim of pan to receive the floor finishing (thickness as indicated) and making good floor complete all as specified incl cutting to the flush pipe and necessary repair to the floor complete all as specified and directed.

S&F in repair PVC Flushing Cistern 10 litre capacity, Low Level Valve Less, Symphonic Action type, White, with Inlet, Ball Valve, Float and Handle including 32mm dia PVC Flush Pipe, a Pair of MS Brackets,CP flush bend including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 including taking down unserviceable Flushing Cistern and connected Items of any description, complete all as specified and as directed.

S&F in repair Sinks with out drainage board made of stainless steel 0.75mm thick kitchen or laboratory, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed as approved by Engr-in-Charge

S&F in repair PVC Connections 15mm size with PTMT Nuts of length 600mm and fixed, complete all as specified and as directed.

Dismantling of CI/AC pipe 100mm dia jointed in cement mortar and taking out of trench or from wall for refixing complete all as specified.

M&L for cast iron spun pipe 100mm dia for soil, waste or vent pipe in any lengths with or without ears, jointed with and including cement joints fixed to walls including necessary clamps etc., complete all as specified and as directed.

M&L for cast iron spun pipe 100mm dia for soil, waste or vent pipe in any lengths with or without ears, jointed with and including cement joints laid in trenches or floor complete all as specified and as directed.

Dismantling of CI/AC pipe 75mm dia or less jointed in cement mortar and taking out of trench if required complete all as specified.

M&L for cast iron spun pipe 75mm dia for soil, waste or vent pipe in any lengths with or without ears, jointed with and including cement joints fixed to walls including necessary clamps etc., complete all as specified and as directed.

M&L for cast iron spun pipe 75mm dia for soil, waste or vent pipe in any lengths with or without ears, jointed with and including cement joints laid in trenches or floor complete all as specified and as directed.

M&L for cast iron spun pipe 50mm dia for soil, waste or vent pipe in any lengths with or without ears, jointed with and including cement joints fixed to walls including necessary clamps etc., complete all as specified and as directed.

S & F CI spun pipe bends with oval acess door 100mm bore of any radius, diminishing piece or tappers jointed with cement joint complete all as specified and as directed.

S & F CI spun pipe bends with oval access door 75mm bore of any radius, diminishing piece or tappers jointed with cement joint complete all as specified and as directed.

S&F CI spun pipe branch piece 100mm bore, double (equal or unequal) with parallel branches and fitted with over access door jointed with cement joint complete all as specified and directed

S & F CI floor tarp, with grating including jointing to waste pipe in cement joint, fixed in cement concrete type B-1 (1:2:4) of size 75mm, fixed in repair including making joint water tight, complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed including necessary fittings like socket, bend, elbow, single/double tee etc in any length with rubber ring joints fixed with clamps of flat iron and including bolts and nuts and securing ends of stays to wall or roof and making good with cement mortar 1:3 or with PCC 1:2:4 including two coats of cement base paint /colour wash complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc raking out joints hacking for key scrabbing down water etc complete all as specified and directed.

M&L for 15mm thick cement plaster in cement mortar (1:4) on fair faces of brick or concrete surfaces using WPC where ever required as per manufacturerer's instructions and finishing the surface even and smooth (without using extra cement) etc. including finishing even and fair complete all as specified and directed. NOTE -WPC shall be measured and paid separetely.

Supply only WPC complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work in cement mortar 1:6 finished even and fair without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick in cement mortar 1:3 on fair faces or concrete ceiling surfaces finished even and fair without using extra cement complete.

M&L for Preparation on new plastered surfaces of wall, and apply two coat of exteriar emulsion paint (Apex) over a coat of primer complete all as specified and directed.

M&L for Preparation, cleaning scraping of old treated surfaces of wall and apply two coat of Exerior emulsion paint (Apex) over a coat of primer complete all as specified and directed.

M&L for Preparing new plastered or unplastered surfaces of walls and applying 2mm thick (in 2 coat) wall care, putty and two coats of distemper oil emulsion, white or tinted over a coat of primer, complete all as specified and directed.

M&L for preparing old treated surfaces of walls and applying 2mm thick wall care, putty and two coats of distember oil emulsion, white or tinted over a coat of primer, complete all as specified and directed.

M&L preparing new plastered or unplasted surfaces of ceiling and applying two coats of white wash over a coat of chalk whiting, complete all as specified and directed.

M&L preparing, washing washing, rubbing down and painted surfces of old/untreated surfaces of plastered or unplastered surfaces of ceiling and applying two coats of white wash, complete all as specified and diretecd

M&L for applying two coats of synthetic enamel painting over a coat of pink primer on new wooden surfaces exc 10cm width or girth including preparation of surfaces complete all as specified and directed.

M&L for one coat of synthetic enamel paint to old decorated wooden surfaces of girth exc 10 cm including preparation of surface complete all as specified and directed.

M&L for two coats of synthetic enamel painting over a coat of red oxide zinc chrome primer on new steel surfaces over 10cm width or girth including preparation of surface complete all as specified and directed.

M&L for one coat of synthetic enamel paint to old decorated steel surfaces of girth exc 10cm including preparation of surfaces complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F framed work such as gate, grills,gratings, etc with ends of bars shouldered and / or riveted or forged into spikes; framed guard ; barred iron doors; ladders ; framed balusters; walk ways; railing and simillar work Con-forming to Fe 290 Gde E-165 complete all as specified and directed..

S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering /cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

Taking down chowkats or frames n.exc 1.50 sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats or frames exc 1.50 sqm but n.exc 4.00sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down shutters of any description exc 1 sqm but not exc 2 sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 sqm but not exc 2 sqm each and refixing in the same opening complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC Sheet rainforced with MS square tube all complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame work made out of MS tubes for top or bottom rail MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheets for trip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail, and bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to stiles and rail with suitable PVC sheets beading and jointed together with solvent cement supplying and fixing in the frame at site as specified in cluase No 8.2.1 B.of SSR Part-II all as specified and directed.

S&F aluminium three track powder coated of any color (thickness of powder coating not less than 50 micron) sliding window with three sliding shutter the size of outer frame three track 92x31.5x1.2mm (using two track for glazed window shutter and one track for wire gauged), the section shutter size 37x18x1.2mm) and glazing with 4.8mm thick glas (Plain/floated) incl allround suitable rubber gasket and MS wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed on aluminium flat and inserted in the frame of shutter with tracking arrangement each sliding window shall be provided with one number handle incl rocking arrangement & 2 numbers sliding rollers of nylon with incl all necessary fittings complete all as specified and directed.

S&F aluminium ventilator powder coated of any color (thickness of powder coating not less than 50 micron) top hung vetilator shutter the size of outer frame 92x31.5x1.2mm and glazing with 3mm thick figured and another shutter of wiremesh incl allround suitable rubber gasket and MS wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed on aluminium flat and inserted in the frame of shutter with shall be provided with one number handle incl locking arrangement with incl all necessary fittings complete all as specified and directed.

S&F powder coated Anodised aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Pressed steel frames for doors of size 125 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, all as specified and directed by engnieer in charge.

S&F factory made 35mm thick flush shutters, solid core construction, with block board core and plywood face panesls, commercial type on both sides, complete all as specified and as directed.

M&L 0.9mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

S&F 35 mm thick glazed and skelton shutter open rebated and prepared to receive glass, gauge etc,(with out sash bars) edges of framing plain chamfered or rounded fitted with cut or mitred beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Sec-8, clause 8.23(a) 2nd class hard wood (Shisham), complete all as specified and as directed

S&F Aluminium alloy, anodised, sliding door bolt with haps, staple (bolt type) and fixing clips with sheet, cast and extruded section and fixing bolt and sliding bolt of extuded sections or cast aluminium alloy and fixed 300 mm long complete all as specified and directed.

S&F 150 mm overall length floor stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed

S&F Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed

S & F aluminium handle, cast type anodized 150mm size complete all as specified and directed.

S & F 200 mm long aluminium anodized barrel tower bolts of extruded section lcomplete all as specified and as directed.

S&F Butt hinges medium weight cold rolled mild steel of 100mm long complete all as specified and directed.

S&F figured glass pin headed type and glazing with oil putty in square n. exc 0.5 sqm in each pane 3mm thick glass complete all as specified and directed.

S&F mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperature 1.4 mm and fixed with alluminium staple and around all beading complete all as specified and as directed

S&F in repair Decorative Stainless steel tubular curtain rail of 25mm dia incl six nos curtain ring per running mtr and one number of brackets on each end and one no of globe on each end of the rod per opening of door / window (make and materail approved by Engineer-in-charge) complete all as specified and directed.

Taking down carefully aluminium/ copper wiring of any size (for light, fan, socket or power etc complete) including fixture and fittings such as switches, sockets, ceiling roses, pendent holders regulators, tube lights etc and making good disturbed surfaces of wall, roof etc to match with existing surface complete all as specified and directed.

S&F point wiring for one light point/ fan (independent) point controlled by one, one way switch with 1.5sqmm size, PVC insulated and unsheathed 1100 volts grade, single core stranded (multistrand) copper conductor (FRLS) PVC cable drawn into and including medium grade PVC conduit (not less than 20mm dia) with all fittings and accessories fixed concealed (including chase cutting in brick/ stone masonry walls for fixing conduit and plastering and whitewash/ colouring the external surface and matching the same with existing surface) and sunk cast iron or pressed steel terminal boxes for mounting fittings like switches, sockets & fan regulators etc with 3mm thick plastic laminated sheet covers fixed with brass screws and cup washers including one continuous run of PVC insluated (green colour) 1.5Sqmm multistranded copper conductor cable earth wire and connected to earth dolly complete all as specified and directed. Note:- Wiring shall be done in colour coding as directed by Engineer in charge.

All as per item No. 123 herein before but one light point controlled by one two way switch complete all as specified and directed.

All as per item No. 123herein before but one socket outlet 5Amps on the same board complete all as specified and directed.

All as per item No. 123 herein before but one 3 pin socket outlet 5Amps independent complete all as specified and directed.

All as per item No. 123 herein before but one bell point controlled by one bell push switch complete all as specified and directed.

All as per item No. 123 above but with 2.5 Sqmm two single core and 2.5 Sqmm one single core as earth specified and directed.

S&F lamp holder PVC insulated body with back plate for angle/ battern fitting complete all as specified and directed.

S&F switch piano flush type single pole, onw way 5 Amp complete all as specified and directed.

S&F switch piano, flush tupe single pole 15Amp complete all as specified and directed.

S&F switch piano flush type single pole, two way 5 Amp complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin, 5 and 15 Amp flush type complete all as specified and directed.

Supply & Fixing socket outlet 2 in 1, 3 pin, 5 Amp flush type complete all as specified and directed.

Supply & Fixing Bell push, flush type , 5 Amp complete all as specified and directed.

Supply & Fixing steped type electronic fan regulator flush type on the existing phenolic laminatedsheet etc complete all as specified and directed.

Supply and fixing bell electric multi musical type AC 230 volts, 50 Hz complete all as specified and directed.

S&F ceiling rose surface bakelite 3 terminal with base plate complete all as specified and directed.

Material and labour for Sub main wiring with 2 run of 6 Sqmm (nominal area) FRLS, PVC Insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in to and including Rigid non metallic PVC conduit ( ISI marked) Heavy grade, 25 mm dia (external) inclusive of junction/terminal boxes, all fittings and accessories fixed concealed with and including 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB including cutting and chasing and making good surface as original by plastering and whitewash/ colour/ distemper etc including taking down existing old sub main wiring complete all as specified and directed. Note :- Two run of 6 sqmm, one run of 6 sqmm earth wire and one run of PVC conduit will be measured as one unit ie one running metre.

Supply and fixing LED lights fitting 1x 20W (warm/milky white as required on site), 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and life of tube light not less than 50,000 hours.complete all as specified and directed. Make Havells cat pat LUMILINEBS20WLED865SPCWH or equivalent of phillips/wipro/Bajaj/Surya complete Note:- LED tube light shall be purches to get minimum 2 year warrenty of material from manufracturer.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible opper conductor cable of suitable size complete all as specified and directed.

Supply & Fixing sheet metal enclosure for DBs(double door type) single pole and neutral 12 way including blanking plate as required with 200 Amps rated bus bar, 240 volts fixed complete all as specified and directed .

Supply & Fixing 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN 40 TO 63 Amp and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed .

Supply & Fixing 240V, 10KA 'B' curve miniature circuit breaker (MCB) of single pole 5 to 32 Amp and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed .

Supply and Fixing propeller type AC ventilating fans 230 volts, 50 C/S heavy duty 1400 RPM, 300 mm sweep (Exhaust fan) metal body and blades protected by metal guards,Bird guard for safetry,two sleeves bearings, with frame and louvers complete including the ragged bolts in wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated three core white 23/.0076 copper cable, rubber insulated from ceiling rose to exhaust fan motor with mosquito mesh in out side complete all as specified and directed.

S & F exhaust fan made of sturdy Engineering plastic type ISI Mark, copper winding of sweep 250 mm size complete with louvers including cutting opening through brick/stone /PCC block wall, making of holes and grouting of suitable size of nuts and bolts for 250 mm exhaust fan and making good dismantled portion and making connection with wire of suitable size and connecting accessories complete all as specified and directed.

S & F LED light fitting 1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. Make : Havells cat pat HEXAFT10WLED857SSYMBOPC or equivalent cat part in make phillips/wipro/Bajaj & C&S complete all as specified and directed. Note:- Contractor shall submit 2 year warrenty of material from manufracturer alongwith purchase voucher.

Supply and fix water heater storage type electric supplied and installed complete of capacity 25 ltrs heating element upto 2 KW, BEE 5 Star rate complete including making connection with industrical socket, ultra thick SS inner tank of superior 304 grade, Fire retardant ISI Mark supply cord, Rust & shock proof ABS body, Compact & easy to install and proper hanging on nut bolts washers grouted on wall and PVC pipe for connection of hot and cold water complete all as specified and directed by Engr-in-charge. Make - Bajaj/Crompton/Havells and equivalent make as specified in particular specifications.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories (including ceiling clamp/hook fixing in ceiling/roof with fashner/nut & bolts), 230 V, 1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed by Engineer-in-Charge.

aditya construction (BID ID -3516148)